Manual-KBU650 Carel.pages
Transcription
USER MANUAL KBU-650, KBU-1000 SERIES BEVERAGE COOLER Carel controller KBU-650 COMPRESSOR BEVERAGE COOLER www.kingsbottle.com KBU-1000 ! CONTENTS CONGRATULATIONS ! Congratulations and thank you for choosing our KingsBottle Beverage Coolers . We are sure you will find your new appliance a pleasure to use . Before you installing and operating the Beverage Cooler, we recommend that you read through the relevant sections of this manual, which provides a description of your Beverage Cooler and its functions . ! To avoid the risks that are always present when you use an electric appliance, it is important that the appliance is installed correctly and that you read the safety instructions carefully to avoid misuse and hazards . ! We recommend that you keep this instruction booklet for future reference and pass it on to any future owners . ! After unpacking the appliance, please check it is not damaged . If in doubt, do not use the appliance but contact us or your local customer care centre TABLE OF CONTENTS CHAPTER CONTENTS PAGE Part I Important Safety & Pre-Use Instructions 3 Part II Diagram & Description of Beverage Cooler 4 Part III Installation Instructions 5-6 Part IV Operating Your Beverage Cooler 7-10 Part V Replacement of Lamp 11 Part VI Care and Maintenance 12 Part VII Troubleshooting Guide 13 Part VIII Technical Data 14 Part IX Warranty Information 16 !! COMPRESSOR BEVERAGE COOLER www.kingsbottle.com 2 +/2146#065#('6;+05647%6+105 +/2146#065#('6;+05647%6+105 +/2146#065#('6;+05647%6+105 +/2146#065#('6;+05647%6+105 PART I IMPORTANT SAFETY INSTRUCTIONS 0LEASE¬READ¬THE¬USER¬MANUAL¬CAREFULLY¬AND¬STORE¬IN¬A¬HANDY¬ 5#('6; 5#('6; SAFETY 4. WARNING WARNING WARNING The The refrigerator refrigerator must must be be plugged plugged into into its its own own Don’t use extension cords or adapter plugs with this WARNING dedicated 220-240V, 50Hz AC electrical outlet. The refrigerator must be plugged into its own dedicated 220-240V, 50Hz AC electrical outlet. cooler . plug must dedicated 220-240V, ACinto electrical The be accessible when the The refrigerator must be50Hz plugged ownoutlet. isis The plugcord must accessible theitsrefrigerator refrigerator If the power is be damaged, have when it replaced by a in position. The plug must be accessible when the refrigerator dedicated 220-240V, 50Hz AC electrical outlet. is in position. qualified service technician . inisposition. ItThe essential the power point is properly earthed to plug mustthe bepower accessible the refrigerator It is essential pointit,iswhen properly earthed Unplug the cooler before cleaning or changing the lightto is ground. Consult a qualified electrician if you are It is essential the power point is properly earthed to in position. ground. qualified electrician if you are unsure. unsure. bulb to avoidConsult electric a shock . The symbols you will see in this booklet have these meanings: ground. Consult a qualified electrician if you are unsure. WARNING Don’t use extension cords or adapter plugs with ItDon’t is unplug essential the power pointorthe isadapter properly earthed 7. Never cooler by pulling electrical cord with as tothis WARNING use the extension cords plugs this WARNING refrigerator. Don’t use extension cords or adapter plugs withunsure. this 6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLAMLACPLGLEWMSPNCPQML?JQ?DCRW ground. Consult a qualified electrician if you are this may damage it. Grip the plug firmly and pull straight refrigerator. 6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLAMLACPLGLEWMSPNCPQML?JQ?DCRW This symbol indicates information concerning your personal safety 6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLAMLACPLGLEWMSPNCPQML?JQ?DCRW Ifrefrigerator. cord damaged, have by outDon’t WARNING use extension or adapter with this If. the the power power cord isis cords damaged, have itplugs it replaced replaced by aa If the power cord is damaged, have it replaced by a qualified service technician. 8. Choose a location for your cooler that isn’t too cold . The refrigerator. 6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLAMLACPLGLEWMSPNCPQML?JQ?DCRW qualified service technician. CAUTION qualified service technician. ambient room temperature should be above 50°F . Unplug the refrigerator before cleaning it, or changing CAUTION IfUnplug the power cord is damaged, have it replaced by a the refrigerator before cleaning it, or changing CAUTION 6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLMLFMURM?TMGBB?K?EGLERFC 9. Stand your in aavoid dry place – avoid areas of it, high Unplug the refrigerator before cleaning or changing the lightcooler bulb to electric shock. qualified service technician. 6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLMLFMURM?TMGBB?K?EGLERFC the light bulb to avoid electric shock. 6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLMLFMURM?TMGBB?K?EGLERFC ?NNJG?LAC moisture orunplug humidity .avoid CAUTION the light bulb to electric shock. This symbol indicates information on how to avoid damaging the Never the refrigerator pullingit,theorelectrical ?NNJG?LAC Unplug the refrigerator before by cleaning changing Never unplug the refrigerator by pulling the electrical ?NNJG?LAC 10. Don’t put the cooler in frosty or unprotected likeelectrical a appliance Never unplug the refrigerator by pulling the 6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLMLFMURM?TMGBB?K?EGLERFC cord as this may damage it. Grip theareas plug firmly and the light bulb to avoid electric shock. cord as this may damage it. Grip the plug firmly and garage or on the verandah . cord as this may damage it. Grip the plug firmly and ?NNJG?LAC pull straight out. Never unplug the refrigerator TIPS & INFORMATION pullthestraight straight out. 11. Keep cooler out of direct sunlightby . pulling the electrical pull out. TIPS & INFORMATION Choose athe location for your refrigerator that too cold. TIPS & INFORMATION cord as this may it. Grip the plugisn’t 12. Don’t locate coolerdamage near stoves, fires or heaters .firmly 6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRSQCMDRFC?NNJG?LAC Choose a location location for your your refrigerator that isn’t too and cold. Choose a for refrigerator that isn’t too cold. 6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRSQCMDRFC?NNJG?LAC The ambient room temperature should be above 10°C. pull straight out. 6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRSQCMDRFC?NNJG?LAC 13. When installed correctly, your cooler should: The ambient room temperature should be above 10°C. TIPS & INFORMATION The ambient room temperature should be above 10°C. This symbol indicates tips and information about use of the Standadequate your refrigerator in back arefrigerator dryand place –for avoid areas a location foratyour that isn’t cold. Have space the sides air too • Choose Stand your refrigerator in a a dry dry place place – avoid avoid areas 6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRSQCMDRFC?NNJG?LAC Stand your refrigerator in – areas WARNING appliance of high moisture or humidity. ENVIRONMENTAL TIPS The ambient room temperature should be above 10°C. circulation. of high high moisture moisture or or humidity. humidity. ENVIRONMENTAL TIPS TIPS of ENVIRONMENTAL Don’t put refrigerator in frosty or unprotected areas Be aligned torefrigerator the surrounding . its 6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRCAMLMKGA?J?LB • Stand yourthe acupboards dry place – avoid The refrigerator must beinplugged own areas Don’t put the refrigerator in frosty into or unprotected unprotected areas 6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRCAMLMKGA?J?LB Don’t put the refrigerator in frosty or 6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRCAMLMKGA?J?LB like a garage or on the verandah. Have doors that will self-close from a partially open CAMJMEGA?JSQCMDRFC?NNJG?LAC • of high moisture or humidity. ENVIRONMENTAL TIPS dedicated 220-240V, 50Hz AC electrical outlet.areas like a garage or on the verandah. CAMJMEGA?JSQCMDRFC?NNJG?LAC like a garage or on the verandah. CAMJMEGA?JSQCMDRFC?NNJG?LAC 0LEASE¬READ¬THE¬USER¬MANUAL¬CAREFULLY¬AND¬STORE¬IN¬A¬HANDY¬ position Keep the must refrigerator out in of frosty direct sunlight. Don’t put the refrigerator unprotected areas The plug be accessible whenor the refrigerator is 6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRCAMLMKGA?J?LB Keep the refrigerator refrigerator out of indirect direct sunlight. place for indicates later reference. Keep the out of sunlight. This symbol tips and information about economical and 14. Please inspect andor clean the filter front venting grill Meanings of symbols used in this manual are shown below: like a garage on the verandah. in position. CAMJMEGA?JSQCMDRFC?NNJG?LAC Don’t locate the refrigerator near stoves, fires or heaters. Meanings symbols used in this manual shown below: every month. The symbols will see in this booklet haveare these meanings: Failure tothe clean will void the warranty and ecological use of ofyou the appliance locate refrigerator stoves, fires or heaters. Keep the refrigerator out of near direct sunlight. ItDon’t is essential the power point is properly earthed to installed increaseWhen the running costs.correctly, your refrigerator should: 6FGQQWK@MJGLBGA?RCQLCTCPRMBMRFGQ 0LEASE¬READ¬THE¬USER¬MANUAL¬CAREFULLY¬AND¬STORE¬IN¬A¬HANDY¬ Please read the user manual carefully and store in a handy place later reference. 0LEASE¬READ¬THE¬USER¬MANUAL¬CAREFULLY¬AND¬STORE¬IN¬A¬HANDY¬ 5. placeforfor forlater later reference. place reference . The symbols you will see in this The symbols you will see in this booklet have these meanings: place for later reference. The symbols you will see in this booklet have these meanings: 0LEASE¬READ¬THE¬USER¬MANUAL¬CAREFULLY¬AND¬STORE¬IN¬A¬HANDY¬ booklet have these meanings: The symbols will see in this booklet have these meanings: 6. place for lateryou reference. !! ! !! ! !! ! +/2146#065#('6;+05647%6+105 !! ! !! WARNING ! 5#('6; ! When installed correctly, your should: ground. Consult a qualified electrician if fires you are unsure. –locate Have adequate space atrefrigerator the back and Don’t the refrigerator near stoves, or sides heaters. – Have adequate space at the back and sides Don’t use extension cords or adapter plugs with this for air circulation (refer to page 9). When for installed correctly,(refer your to refrigerator air circulation page 9). should: refrigerator. – Be aligned to the surrounding cupboards. –– Have adequate at the back and sides Be aligned to thespace surrounding cupboards. –power Have will self-close a partially If the cord isthat damaged, it9). replaced by a BEFORE USING YOUR BEVERAGE COOLER air doors circulation (refer to have pagefrom OR INJURY WHEN USING YOUR APPLIANCE, FOLLOW 6FGQQWK@MJGLBGA?RCQ?JU?WQBMRFGQ – for Have doors that will self-close from a partially open position. 1. Remove exterior and interior packing. cupboards. qualified service technician. –the Be aligned to the surrounding THESE BASIC PRECAUTIONS: open position. CAUTION WARNING 2. Before connecting the Beverage Cooler to the power – Have doors that will self-close from Unplug the refrigerator before cleaning it, aorpartially changing 1. Read all instructions before using the Beverage Cooler. WARNING source, letopen it bulb stand approximately 6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLMLFMURM?TMGBB?K?EGLERFC position. the light toupright avoidforelectric shock.24 hours. s¬¬)F¬PRESSURISED¬AEROSOL¬CONTAINERS¬BEAR¬THE¬WORD¬ 2. DANGER or WARNING: Risk of child entrapment. s¬¬‘flammable’ )F¬PRESSURISED¬AEROSOL¬CONTAINERS¬BEAR¬THE¬WORD¬ This will reduce the possibility of a malfunction in the ?NNJG?LAC and/or a smallareflame symbol, Child entrapment and suffocation not only problems of the WARNING Never unplug the refrigerator by pulling the electrical WARNING ‘flammable’ and/or aappliances small flame symbol, cooling system from handling during transportation. WARNING past. Junked or abandoned are still dangerous… do not store them inside any refrigerator or cord as this may damage it. Grip the plug firmly and s¬¬)do F¬PRESSURISED¬AEROSOL¬CONTAINERS¬BEAR¬THE¬WORD¬ not them inside any refrigerator or 3. 4#4'(4+)'4#069#40+0) Clean the interior surface with lukewarm water using a doif they not store store them inside any refrigerator or even will “just sit so in the garage for a few freezer. If you do you mayflame cause andays”. explosion. 4#4'(4+)'4#069#40+0) pull straight out.contain a small quantity of environmentally 4#4'(4+)'4#069#40+0) ‘flammable’ and/or a small symbol, This appliance may WARNING TIPSyou INFORMATION freezer. IfIf & you do so may cause an explosion. soft cloth. freezer. you do away so you you may cause anCooler: explosion. 3. Before throw your oldrefrigerator Beverage s¬¬do 7 HEN¬YOU¬DISPOSE¬OF¬YOUR¬OLD¬REFRIGERATORS¬AND¬FREEZERS¬ This appliance may contain a quantity of environmentally This appliance may contain a small small quantity of environmentally not store them inside any or Choose a location for your refrigerator isn’t too cold. friendly, but flammable, non-synthetic R600athat refrigerant: s¬¬ 7 4#4'(4+)'4#069#40+0) s¬¬remove 7HEN¬YOU¬DISPOSE¬OF¬YOUR¬OLD¬REFRIGERATORS¬AND¬FREEZERS¬ HEN¬YOU¬DISPOSE¬OF¬YOUR¬OLD¬REFRIGERATORS¬AND¬FREEZERS¬ 6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRSQCMDRFC?NNJG?LAC Take off the door. any doors. Children can suffocate if they get friendly, but flammable, non-synthetic R600a refrigerant: friendly, but flammable, non-synthetic R600a refrigerant: • freezer. Ifany youdoors. do soChildren you maycan cause an explosion. The ambient room temperature should be above 10°C. s¬¬ % NSURE¬THAT¬THE¬TUBING¬OF¬THE¬REFRIGERANT¬CIRCUIT¬IS¬NOT¬ remove suffocate if they get This appliance may contain a small quantity of environmentally remove any suffocate they Leave thedoors. ShelvesChildren in pieces can so that children ifmay notget s¬¬ %%NSURE¬THAT¬THE¬TUBING¬OF¬THE¬REFRIGERANT¬CIRCUIT¬IS¬NOT¬ trapped inside. s¬¬damaged NSURE¬THAT¬THE¬TUBING¬OF¬THE¬REFRIGERANT¬CIRCUIT¬IS¬NOT¬ • HEN¬YOU¬DISPOSE¬OF¬YOUR¬OLD¬REFRIGERATORS¬AND¬FREEZERS¬ s¬¬7 during transportation and installation. Stand your refrigerator in a dry place – avoid areas trapped inside. friendly, but flammable, non-syntheticand R600a refrigerant: inside. climb inside easily. damaged during s¬¬remove 4trapped HIS¬APPLIANCE¬CONTAINS¬INSULATION¬FORMED¬WITH¬mAMMABLE¬ damaged during transportation transportation and installation. installation. any doors. Children can suffocate if they get s¬4HE¬ROOM¬FOR¬INSTALLING¬APPLIANCE¬MUST¬BE¬AT¬LEAST¬M¬PER¬ of high moisture or humidity. s¬¬ 4 HIS¬APPLIANCE¬CONTAINS¬INSULATION¬FORMED¬WITH¬mAMMABLE¬ ENVIRONMENTAL TIPS s¬¬ % NSURE¬THAT¬THE¬TUBING¬OF¬THE¬REFRIGERANT¬CIRCUIT¬IS¬NOT¬ s¬¬blowing 4HIS¬APPLIANCE¬CONTAINS¬INSULATION¬FORMED¬WITH¬mAMMABLE¬ 4. Never allow children to operate, play with,by or carefully crawl inside s¬4HE¬ROOM¬FOR¬INSTALLING¬APPLIANCE¬MUST¬BE¬AT¬LEAST¬M¬PER¬ gases. Avoid safety hazards trapped inside. s¬4HE¬ROOM¬FOR¬INSTALLING¬APPLIANCE¬MUST¬BE¬AT¬LEAST¬M¬PER¬ +/2146#065#('6;+05647%6+105 8gDon’t ofWARNING refrigerant. The amount in of frosty refrigerant charged in areas the blowing gases. Avoid safety hazards by carefully putduring the refrigerator unprotected damaged transportation and or installation. 6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRCAMLMKGA?J?LB blowing gases. Avoid safety hazards by carefully the appliance. 8g of refrigerant. The amount of refrigerant charged in the disposing of this appliance. s¬¬4disposing HIS¬APPLIANCE¬CONTAINS¬INSULATION¬FORMED¬WITH¬mAMMABLE¬ 8g of refrigerant. The amount of refrigerant charged in the appliance can be found on the rating plate on the appliance. of this appliance. like a garage orfound on the verandah. s¬4HE¬ROOM¬FOR¬INSTALLING¬APPLIANCE¬MUST¬BE¬AT¬LEAST¬M¬PER¬ CAMJMEGA?JSQCMDRFC?NNJG?LAC disposing of appliance thisAvoid appliance. 5. Never clean parts with flammable fluids. The appliance can be on the rating plate on the appliance. blowing gases. safety hazards by carefully The refrigerator must be plugged into its own appliance can be found on the rating plate on the appliance. s¬+EEP¬VENTILATION¬OPENINGS¬IN¬THE¬APPLIANCE¬ENCLOSURE¬OR¬ 8gKeep of refrigerant. The amount of direct refrigerant charged in the the refrigerator out of sunlight. fumes can create a fire hazard or explosion. s¬+EEP¬VENTILATION¬OPENINGS¬IN¬THE¬APPLIANCE¬ENCLOSURE¬OR¬ disposing of this appliance. 220-240V, 50Hz AC electrical outlet. s¬+EEP¬VENTILATION¬OPENINGS¬IN¬THE¬APPLIANCE¬ENCLOSURE¬OR¬ in dedicated the built-in obstruction. appliance canstructure, be found clear on theof rating plate on the appliance. Meanings of symbols used of in any thisother manual are shown 6. Do not store in the vicinity appliance. Do notbelow: in Don’t the built-in structure, clear of obstruction. 0LEASE¬READ¬THE¬USER¬MANUAL¬CAREFULLY¬AND¬STORE¬IN¬A¬HANDY¬ locate the refrigerator near stoves, fires or heaters. in the built-in structure, clear of obstruction. The plug must be accessible when the refrigerator is s¬$O¬NOT¬USE¬MECHANICAL¬DEVICES¬OR¬OTHER¬MEANS¬TO¬ s¬+EEP¬VENTILATION¬OPENINGS¬IN¬THE¬APPLIANCE¬ENCLOSURE¬OR¬ store or any other flammable vapors. The s¬$O¬NOT¬USE¬MECHANICAL¬DEVICES¬OR¬OTHER¬MEANS¬TO¬ place fornear latergasoline reference. s¬$O¬NOT¬USE¬MECHANICAL¬DEVICES¬OR¬OTHER¬MEANS¬TO¬ in position. When installed correctly, your refrigerator should: accelerate the defrosting process, other than those in the built-inthe structure, clear of obstruction. 6FGQQWK@MJGLBGA?RCQLCTCPRMBMRFGQ canyou create fire hazard or explosion. accelerate defrosting process, other than those The fumes symbols willasee in this booklet have these meanings: accelerate the the defrosting process, other than those – Have adequate space the back and sides recommended by It is essential power point isatproperly earthed to s¬$O¬NOT¬USE¬MECHANICAL¬DEVICES¬OR¬OTHER¬MEANS¬TO¬ recommended by the the manufacturer. manufacturer. 3 recommended by the manufacturer. for air circulation (refer to page 9). s¬4HE¬ROOM¬FOR¬INSTALLING¬APPLIANCE¬MUST¬BE¬AT¬LEAST¬M 3 ground. Consult a qualified electrician if you are accelerate the defrosting process, other than thoseunsure. 6FGQQWK@MJGLBGA?RCQ?JU?WQBMRFGQ s¬4HE¬ROOM¬FOR¬INSTALLING¬APPLIANCE¬MUST¬BE¬AT¬LEAST¬M 3 s¬4HE¬ROOM¬FOR¬INSTALLING¬APPLIANCE¬MUST¬BE¬AT¬LEAST¬M – Be aligned to the surrounding cupboards. per 8g of refrigerant. The amount of refrigerant charged recommended by the manufacturer. WARNING userefrigerant. extension The cords or adapter plugs with this perDon’t 8g of amount of refrigerant charged per 8g of refrigerant. The amount of refrigerant charged 3 – Have doors that will self-close from a partially in the appliance can be found on the rating plate on s¬4HE¬ROOM¬FOR¬INSTALLING¬APPLIANCE¬MUST¬BE¬AT¬LEAST¬M 1. The cooler must be plugged into its own dedicated in refrigerator. the appliance can be found on the rating plate on 6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLAMLACPLGLEWMSPNCPQML?JQ?DCRW in the appliance can be found onoftherefrigerant rating plate on open position. the appliance. per refrigerant. amount charged 110-115V, 50/60Hz AC electrical outlet . the appliance. If 8g the of power cord isThe damaged, have it replaced by a the appliance. WARNING in the appliance cantechnician. be found on the rating plate on 2. The plug must be accessible when the cooler is in qualified service the appliance. CAUTION position. s¬¬)F¬PRESSURISED¬AEROSOL¬CONTAINERS¬BEAR¬THE¬WORD¬ Unplug the refrigerator before cleaning it, or changing 3. It is essential the power point is properly earthed to ‘flammable’ and/or a small flame symbol, 6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLMLFMURM?TMGBB?K?EGLERFC theWARNING light bulb to avoid electric shock. . Consult qualified electrician if you or are unsure . doground not store themainside any refrigerator ?NNJG?LAC 4#4'(4+)'4#069#40+0) Never unplug the refrigerator by pulling the electrical freezer. If you do so you may cause an explosion. This appliance may contain a small quantity environmentally cord as this may damage it. Grip the of plug firmly and s¬¬7HEN¬YOU¬DISPOSE¬OF¬YOUR¬OLD¬REFRIGERATORS¬AND¬FREEZERS¬ friendly, but flammable, non-synthetic R600a refrigerant: pull straight out. TIPSany & INFORMATION remove doors. Children can suffocate if they get s¬¬%NSURE¬THAT¬THE¬TUBING¬OF¬THE¬REFRIGERANT¬CIRCUIT¬IS¬NOT¬ Choose a location for your refrigerator that isn’t too cold. trapped inside. 6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRSQCMDRFC?NNJG?LAC damaged during transportation installation. The ambient room temperature and should be! above 10°C. s¬¬4HIS¬APPLIANCE¬CONTAINS¬INSULATION¬FORMED¬WITH¬mAMMABLE¬ s¬4HE¬ROOM¬FOR¬INSTALLING¬APPLIANCE¬MUST¬BE¬AT¬LEAST¬M¬PER¬ Stand your refrigerator in a dry place – avoid areas blowing gases. Avoid safety hazards by carefully 8gofofhigh refrigerant. Theoramount of refrigerant charged in the moisture humidity. ENVIRONMENTAL TIPS disposing of this appliance. appliance can be found on the rating plate on the appliance. Don’t put the refrigerator in frosty or unprotected areas 6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRCAMLMKGA?J?LB s¬+EEP¬VENTILATION¬OPENINGS¬IN¬THE¬APPLIANCE¬ENCLOSURE¬OR¬ a garage or on clear the verandah. CAMJMEGA?JSQCMDRFC?NNJG?LAC www.kingsbottle.com 3 in like the built-in structure, of obstruction. Keep the refrigerator out of direct sunlight. s¬$O¬NOT¬USE¬MECHANICAL¬DEVICES¬OR¬OTHER¬MEANS¬TO¬ Meanings of symbols used in this manual are shown below: accelerate the the defrosting process, Don’t locate refrigerator near other stoves,than firesthose or heaters. recommended by the manufacturer. Meanings of symbols used in this manual are shown below: 6FGQQWK@MJGLBGA?RCQLCTCPRMBMRFGQ 6FGQQWK@MJGLBGA?RCQ?JU?WQBMRFGQ 6FGQQWK@MJGLBGA?RCQLCTCPRMBMRFGQ 6FGQQWK@MJGLBGA?RCQ?JU?WQBMRFGQ 6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLAMLACPLGLEWMSPNCPQML?JQ?DCRW TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, !! 5#('6; !! ! FEATURES PART II DIAGRAM & DESCRIPTION OF BEVERAGE COOLER Lantern Box Glass Door Refrigeration Unit Handle Shelf Caster Wheel Frame COMPRESSOR BEVERAGE COOLER www.kingsbottle.com 4 INSTALLATION PART III INSTALLATION INSTRUCTIONS When moving your Beverage Cooler, please do not incline it more than 45 degrees 6” Locate the Beverage Cooler away from direct sunlight and sources of heat (stove, heater, radiator, etc.) 6” This free-standing model requires adequate ventilation around, minimum 6” ( 150mm ) on either side and the rear is requested. ! www.kingsbottle.com 5 INSTALLATION PART III INSTALLATION INSTRUCTIONS A. GENERAL INSTALLATION INSTRUCTIONS 1. This appliance is designed for free standing. 2. Place your Beverage Cooler on a flat, solid floor that is strong enough to support it when it is fully loaded. To level your Beverage Cooler, adjust the leveling leg at the bottom of the Beverage Cooler 3. When moving your Beverage Cooler, please do not incline it more than 45 degrees. 4. Locate the Beverage Cooler away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct sunlight and heat sources may increase electrical consumption. Extreme cold ambient temperatures may also cause the unit to perform improperly. 5. Avoid locating the unit in damp areas. 6. Plug the Beverage Cooler into an exclusive, properly installed and grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or electrical grounding should be directed to a certified electrician or authorized products service center. B. INSTALLING YOUR BEVERAGE COOLER 1. Move the appliance into its final position . 2. If the appliance is not tilting back as described earlier, minor adjustments can be made to the leveling legs. 3. Compare the alignment of the appliance to the surrounding cupboard . The top of the appliance should be level from side to side (see diagram below) . 4. If the appliance now rocks from one corner to the opposite rear corner, this means that the floor is uneven. You may need to put some packing under the ridge to the rear of the appliance . You could use thin pieces of solid material such as thin board, vinyl floor tiles or laminate . 5. You may now need to fine tune the installation by repeating steps 2, 3 and 4 . 6. Wipe off any dust that has accumulated during shipping and clean following the directions in Part VIII ( Care & Maintenance) 7. Plug the appliance into the power point. Don’t use a double adaptor or extension cord . 8. It is recommended that you let the appliance for an hour or two before you put any wine in it . This will confirm that it is operating correctly and make the conditions appropriate for wine storage . ! Congratulations! You have successfully installed your cooler/refrigerator/freezer COMPRESSOR BEVERAGE COOLER www.kingsbottle.com 6 OPERATION PART IV OPERATING YOUR BEVERAGE COOLER This KingsBottle Refrigerator series comes with the worlds best quality controller from CAREL Italy. Before using your Refrigerator, please read these instructions carefully . SET / Light Switch KEYBOARD : • UP/POWER: Increase the value / holding the button for at least 3 seconds, powers the unit ON or OFF. • DOWN/DEFROST: decrease the value / holding the button for more than 3 seconds start/stop defrost. • SET/MUTE: Use SET after selecting values withe the up and down arrows / alarm mute button. Display and functions During normal operation, the controller displays the value of the probe set using parameter /4 (=1 ambient probe, default, =2 second probe, 3= third probe). In addition, the display has LEDs that indicate the activation of the control functions (see Table 1), while the 3 buttons can be used to activate/deactivate some of the functions (see Table 2). Compressor LED signals icon function ON compressor status on normal operation OFF blink off ON request in progress start up ON Tab. 1 Functions activated using the buttons - PJEZS button normal operation pressing the button alone up ON/OFF down defrost more than 3 s: toggle ON/OFF set mute - 1 s.: display/set the set point - more than 3 s: access parameter setting menu (enter password ‘22’) more than 3 s: start/stop defrost start up pressed together Pressed together start/stop continuous cycle Pressed together start parameter reset procedure for 1 s display firmware vers. code for 1 s RESET current EZY set Tab. 2 ! www.kingsbottle.com 7 OPERATION SETTING THE SET POINT (DESIRED TEMPERATURE) • press SET for 1 s, the set value will start flashing after a few moments; • increase or decrease the value using UP or DOWN; • press SET to confirm the new value. ! SWITCHING THE DEVICE ON/OFF Press UP for more than 3 s. The control and defrost algorithms are now disabled and the instrument displays the message “OFF” alternating with the temperature read by the set probe. ! ! ! MANUAL DEFROST Press for DOWN more than 3 s (the defrost starts only the temperature conditions are valid). CONTINUOUS CYCLE Press UP and DOWN together for more than 3 s. ACCESSING AND SETTING THE FREQUENT PARAMETERS (TYPE F AND TYPE C) 1. press SET for 3 s (the display will show “PS”); • to access the type F and C parameter menu, enter the password “22” using UP/DOWN; • to access the F parameter menu only, press SET (without entering the password); 2. scroll inside the parameter menu using UP/DOWN; 3. to display/set the values of the parameter displayed, press SET, then UP/DOWN and finally SET to confirm the changes (returning to the parameter menu). To save all the new values and exit the parameter menu, press SET for 3 s; To exit the menu without saving the changed values (exit by timeout) do not press any button for at least 60 s. CIRCUIT DIAGRAM COMPRESSOR BEVERAGE COOLER www.kingsbottle.com 8 TABLE OF PARAMETERS CODE PS DESCRIPTION password MIN MAX DEFAULT UOM 0 99 22 - PROBE PARAMETERS /2 probe measurement stability 1 15 4 - /5 select °C/°F (0= °C; 1= °F ) 0 1 1 - /6 disable decimal point 0 1 0 - -50 50 0 (°C/°F) / 10 /C1 probe 1 offset CONTROL PARAMETERS St user set point r1 r2 39 °C/°F rd STANDARD differential 0 19 3 °C/°F r1 minimum set point allowed to the user -50 r2 32 °C/°F r2 maximum set point allowed r1 150 43 °C/°F COMPRESSOR PARAMETERS c0 Start delay when COMPRESSOR ON is required by the Regulation 0 200 6 Min c1 delay between 2 consecutive starts 0 100 0 Min c2 minimum compressor OFF time 0 100 6 Min c3 minimum compressor ON time 0 100 0 Min c4 compressor ON time with duty setting 0 100 0 Min cc Continuous cycle duration 0 15 4 Hours c6 Alarm bypass time after cont. cycle 0 15 2 Hours DEFROST PARAMETERS d0 Type of defrost (0 and 1=defrost by temperature; 2, 3 and 4=defrost by time) 0 4 0 - dI Start defrost condition : interval time 0 199 8 Hours dP End defrost condition : max time defrost duration 1 199 30 Min d4 if defrost when switching the instrument on ( 0=no ; 1=yes ) 0 1 0 - d5 Defrost delay on start-up or from digital input 0 199 0 Min d6 temperature displayed “frozen” during defrost ( when d6=0 “dF” is displayed); Freeze regulation probe temperature before defrost start (when d6=1) 0 1 1 - dd dripping time ( stop compressor after defrost ) 0 15 2 Min d8 LOW temperature alarm bypass time after defrost 0 15 0 Hours d9 defrost priority over compressor protectors ( if d9=1 c2, c3, c4 are bypassed ) 0 1 0 - d/ Evaporator probe reading (read only) - - - °C/°F A0 ALARM PARAMETERS alarm temperature differential -20 20 0 °C/°F AL absolute/relative temperature for low temperature alarm -50 150 -30.2 °C/°F AH absolute/relative temperature for high temperature alarm -50 150 82.4 °C/°F Ad temperature alarm delay 0 199 120 Min EVAPORATOR FAN PARAMETERS F0 Start delay when FAN ON is required by the Regulation 1 100 1 sec Fd0 Fan STANDARD Duty Cycle : ON time 1 100 1 Min FdF Fan STANDARD Duty Cycle : OFF time 1 100 1 Min OTHER PARAMETERS supervisor serial address Optional AUX output configuration 0= No function associated with the output 1= Alarm output usually energised; 2= Alarm output usually de-energised 3= Auxiliary output driven by dig. input [ A4=6/7/8 ] dig. input OPEN=AUX de-energised; dig. input CLOSED=AUX energised 0 207 1 H4 disable buzzer ( 1 = disable ) 0 1 0 H5 ID code (read-only) 0 199 1 H0 H1 - - ! www.kingsbottle.com 9 OPERATION TABLE OF ALARMS ALARM CODE DESCRIPTION E0 probe 1 error=control E1 probe 2 error=defrost LO low temperature alarm HI high temperature alarm EE unit parameter error EF operating parameter erro dF defrost running ! NOTE: The desired temperatures may fluctuate depending on whether the interior light is ON or OFF, the ambient temperature, the location of unit and the orientation of the bottles. The display is just a guide, be guided by how cold your drinks are at consumption. Remember units go into defrost mode and this will show a higher display, it’s only for small periods and doesn’t have time to effect drink temperature. In general once unit has settled it will keep products within 5°F ( 2°C ) of the set temp easily in temperatures up to and beyond 100°F ( 38°C ) . ! ! !! CAUTION: 1. In the event of a power interruption, all previous temperature settings will be automatically saved and each compartment will return to the previous temperature setting. 2. If the unit is unplugged, loses power, or is turned off, you must wait over 6 minutes before restarting. Within this 6 minutes, compressor protect itself and will not start even power ON again 3. When you use the Beverage Cooler. for the first time or restart the Beverage Cooler after having been shut off for a long time, there will be a few degrees variance between the temperature you select and the one indicated on the LED readout for the first few hours of operation. After a few hours of operation, the temperature will normalize to the displayed temperature. !! COMPRESSOR BEVERAGE COOLER www.kingsbottle.com 10 REPLACEMENT OF LAMP PART V REPLACEMENT OF LAMP A. LAMP OF LAMP CASE: 1. Unplug the power cord 2. Remove the lamp case 3. Remove screws at the both end of the lamp case. 4. Remove the decorative plated from the lamp case. 5. separate the lamp from the lamp holder 6. separate the lamp socket and replace the lamp 7. After replacement, ensure lamp case is replaced. B. INTERIOR LAMP: 1. Unplug the power cord 2. Open the glass door 3. Remove lampshade by taking out screws on the right side 4. Separate the lamp from the lamp holder 5. Separate the lamp socket and replace the lamp with care 6. After replacement, ensure lampshade is replaced. ! www.kingsbottle.com 11 5#('6; CARE AND MAINTENANCE +/2146#065#('6;+05647%6+105 WARNING The refrigerator must be plugged into its own dedicated 220-240V, 50Hz AC electrical outlet. PART VI CARE AND MAINTENANCE 0LEASE¬READ¬THE¬USER¬MANUAL¬CAREFULLY¬AND¬STORE¬IN¬A¬HANDY¬ The plug must be accessible when the refrigerator is place for later reference. in position. The symbols you will see in this booklet have these meanings: CLEANING YOUR BEVERAGE COOLER It is essential the power point is properly earthed to ground. Consult a qualified electrician if you are unsure. WARNING Don’t use extension cords or adapter plugs with this refrigerator. 6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLAMLACPLGLEWMSPNCPQML?JQ?DCRW BEFORE CLEANING: Turn off the power, unplug the appliance, and remove all items including all shelves. If the power cord is damaged, have it replaced by a • Wash the inside surfaces with warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda with a qualified service technician. quart of water. CAUTION Unplug the refrigerator before cleaning it, or changing • Wash the shelves with a mild detergent solution. 6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLMLFMURM?TMGBB?K?EGLERFC the light to avoid electric shock. Wring excess water out of the sponge or cloth when cleaning area of the controls, or bulb any electrical parts. • ?NNJG?LAC refrigerator pulling the electrical well andunplug wipe drythe with a clean softby cloth. • Wash the outside cabinet with warm water and mild liquid detergent. Rinse Never cord as this may damage Grip the plug firmly and Oil with a clean rag, to allit. exposed Stainless Steel • After installation, we recommend that owners apply a thin layer of Olive areas. This should then be polished in and buffed off with another clean ragpull to astraight non-oily out. finish. This process will aid protection against TIPS & INFORMATION dirt and other corrosive contaminants, by providing a temporary food-safe shield. TheaOlive Oil layer also makes later polishing Choose location for your refrigerator that isn’t and too cold. 6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRSQCMDRFC?NNJG?LAC The 3-4 ambient room should be above 10°C. removal of fingerprints easier. This process should be repeated frequently every months . ALLtemperature stainless steel can rust, it is a myth that stainless steel doesn’t rust. Stand your refrigerator in a dry place – avoid areas of high moisture or humidity. ENVIRONMENTAL TIPS POWER FAILURE Don’t put the refrigerator in frosty or unprotected areas 6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRCAMLMKGA?J?LB Most power failures are corrected within a few hours and should not affect thelike temperature of your if you minimize the number of a garage or onappliance the verandah. CAMJMEGA?JSQCMDRFC?NNJG?LAC times the door is opened. If the power is going to be off for a longer period of time, to take the stepssunlight. to protect your Keepyou theneed refrigerator outproper of direct contents. Meanings of symbols used in this manual are shown below: Don’t locate the refrigerator near stoves, fires or heaters. When installed correctly, your refrigerator should: FILTER CLEANING 6FGQQWK@MJGLBGA?RCQLCTCPRMBMRFGQ – Have adequate space at the back and sides PLEASE INSPECT & CLEAN FRONT GRILL FILTER EVERY MONTH for air circulation (refer to page 9). Failure6FGQQWK@MJGLBGA?RCQ?JU?WQBMRFGQ to clean will void the warranty and increase the running costs. – Be aligned to the surrounding cupboards. – Have doors that will self-close from a partially VACATION TIME open position. !! ! ! ! ! Short vacations: You may leave the Beverage Cooler operating during vacations of less than three weeks. WARNING Long vacations: If the appliance will not be used for several months, remove all items and turn off the appliance. Clean and dry the interior s¬¬)F¬PRESSURISED¬AEROSOL¬CONTAINERS¬BEAR¬THE¬WORD¬ thoroughly. To prevent mold growth, leave the door open slightly, blocking it open if necessary. !MOVING YOUR BEVERAGE COOLER ‘flammable’ and/or a small flame symbol, WARNING do not store them inside any refrigerator or 4#4'(4+)'4#069#40+0) freezer. If you do so you may cause an explosion. This appliance may contain a small quantity of environmentally 1. Remove all items. s¬¬7HEN¬YOU¬DISPOSE¬OF¬YOUR¬OLD¬REFRIGERATORS¬AND¬FREEZERS¬ 2. Securely tape down all loose items (shelves) inside your appliance. friendly, but flammable, non-synthetic R600a refrigerant: remove any doors. Children can suffocate if they get s¬¬%NSURE¬THAT¬THE¬TUBING¬OF¬THE¬REFRIGERANT¬CIRCUIT¬IS¬NOT¬ 3. Turn the adjustable leg up to the base to avoid damage. trapped inside. damaged during transportation and installation. 4. Tape the door shut. s¬¬4HIS¬APPLIANCE¬CONTAINS¬INSULATION¬FORMED¬WITH¬mAMMABLE¬ s¬4HE¬ROOM¬FOR¬INSTALLING¬APPLIANCE¬MUST¬BE¬AT¬LEAST¬M¬PER¬ 5. Be sure the appliance stays secure in the upright position during transportation. Also protect the outside of the appliance with a blowing gases. Avoid safety hazards by carefully 8g of refrigerant. The amount of refrigerant charged in the blanket or similar item. disposing of this appliance. appliance can be found on the rating plate on the appliance. s¬+EEP¬VENTILATION¬OPENINGS¬IN¬THE¬APPLIANCE¬ENCLOSURE¬OR¬ ENERGY SAVING TIPS the built-in structure, clear of obstruction. 1. The Beverage Cooler should be located in the coolest area of the room,inaway from heat producing appliances, and away from direct s¬$O¬NOT¬USE¬MECHANICAL¬DEVICES¬OR¬OTHER¬MEANS¬TO¬ sunlight. Ventilation at rear also helps a lot with energy usage, so create a positive air flow where possible, although with this range they accelerate the defrosting process, other than those are designed to be fully built in. bya the manufacturer. 2. When you are not using fridge during weekdays etc. it is recommendedrecommended to set the temp at higher level, so set at 47°F ( 8°C ) during 3 periods of non usage, this will not only mean less run time, it also stills¬4HE¬ROOM¬FOR¬INSTALLING¬APPLIANCE¬MUST¬BE¬AT¬LEAST¬M keeps drinks at a temp that won’t be spoiled. It saves energy also per 8g of refrigerant. The amount of refrigerant charged which these days is a growing concern for most households. in the appliance can be found on the rating plate on 3. Keep the cooler stocked, an empty cooler will run longer, believe it or not. the appliance. ! COMPRESSOR BEVERAGE COOLER www.kingsbottle.com 12 TROUBLESHOOTING GUIDE PART VII TROUBLESHOOTING GUIDE PROBLEM Cooler does not operate 1. 2. 3. POSSIBLE CAUSE Not plugged in The appliance is turned OFF at the control panel The circuit breaker tripped or a fuse has blown out Compressor does not start Compressor self-protected and stop operating Wine cooler is not cold Fans stop working or low speed operating enough; can not cooling down to preset Evaporator ice up temp. Door is not well closed Compressor start and stop frequently The light does not work. The Cooler seems to make too much noise. The door will not close properly. Ice up ask engineer for help, check the connection of compressor Ambient temperature is too high and over 38C degree Air venting is not smooth, check the air duct and make sure it is not blocked Fan operates slowly or faulty and stop operating. Door is not closed completely, or door open for long time Compressor or its components faulty Ask engineer for help, power on the cooler, check the fan whether the voltage is normal or not. If the voltage is normal, the fan should be damage Turn OFF the cooler for one hour, sometimes need also open the door, ice on evaporator will melt. Then turn ON and check again. Check the door lock, shelves, or other objects, make sure door is well closed. Check the sealing rubber, make sure door is well sealed. Check the door hinges, make sure they are not loose Condenser is dusty Wash and clean the condenser Cooling system faulty (Gas leakage or blockage) Ask engineer for help The door gasket does not seal properly. Use hair dryer to blow hot air and make the door seal smooth. The sensor connection is wrong. According to the wiring diagram and make the correct connection of sensor The sensor is faulty. Replace with new sensor The door is opened too often. Reduce the times / frequency of door opening. Not plugged in, or the light button is “OFF”. Light itself faulty. Check and make sure the light button is ON, or ask engineer for help. The stand feet is not leveling, vibrations lead to noise Adjust the stand feet and assure they are on level. Pipe hit other objects and lead to noise Adjust the position of pipe slightly At the moment of compressor shut down or start, it is normal for the noise from the vibration generated by the internal moving parts due to inertial motion. nothing is necessary The ratting noise may come from the flow of the refrigerator, which is normal. As each cycle ends, you may hear gurgling sounds nothing is necessary Door is blocked by the door lock, shelves, or other objects. Remove the barrier Door sealing rubber is deformed Repair or replace the rubber seal Door hinges are not loose. Adjust and fasten the hinges. Outlet / suction outlet blockage Remove the barrier Fans stop working or low speed operating Ask engineer for help, power on the cooler, check the fan whether the voltage is normal or not. If the voltage is normal, the fan should be damage The door gasket does not seal properly; or door is opened too often Use hair dryer to blow hot air and make the door seal smooth. Gas leakage or cooling system blockage Ask engineer for help Ambient temperature is too high, or direct sunshine Using conditions need to be improved External cabinet seems Front grill outlet / suction outlet blockage too hot Water drop on glass door Solution Press ON/OFF Check and make sure the power plug is well connected Ask engineer for help Remove the barrier Fans stop working or low speed operating Ask engineer for help, power on the cooler, check the fan whether the voltage is normal or not. If the voltage is normal, the fan should be damage Ambient humidity is high Use a soft cloth to clean the water Door is opened too often Reduce the times / frequency of door opening. The door gasket does not seal properly Use hair dryer to blow hot air and make the door seal smooth. Condensation is forming on outside of glass door Have you turned the ‘Heated Door Function’ ON? located next to the temperature controller. You shouldn’t have condensation on glass with these models if this function is ON. ! www.kingsbottle.com 13 TECHNICAL DATA PART VIII TECHNICAL DATA MODEL NO. KBU-650 KBU-1000 VOLUME 650 Liter 1000 Liter compressor with air-circulated fan cooling compressor with air-circulated fan cooling N / ST N / ST I I 110-115V/50-60HZ 110-115V/50-60HZ 380W 450W 41 - 100 °F 41 - 100 °F 34-43 °F 34-43 °F NET WEIGHT 260.2 Lbs ( 118 Kgs) 326.3 Lbs ( 148kgs ) GROSS WEIGHT 275.6 Lbs ( 125 Kgs) 370.4 Lbs ( 168 kgs) 29.2”W x 28.6”D x 86.5”H (740W x725D x2195H mm) 47.7”W x 31.7”D x 92.2”H ( 1210W x805D x2340H mm) TYPE OF COOLING CLIMATE TYPE ELECTRICITY PROTECTION GRADE NOMINAL VOLTAGE/FREQUENCY RATED POWER(W) AMBIENT TEMPERATURE TEMPERATURE RANGE DIMENSION COMPRESSOR BEVERAGE COOLER www.kingsbottle.com 14 NOTE ! www.kingsbottle.com 15 WARRANTY PART IX WARRANTY INFORMATION Please speak to your Retailer before calling BTO AMERICA LIMITED (also known as KingsBottle) if you did not purchase your Beverage Cooler directly from BTO AMERICA LIMITED ! Limited warranty – If your refrigerator is not operating, KingsBottle reserves the right to repair or replace the refrigerator. KingsBottle may request the consumer to contact a local refrigeration company to service the refrigerator. All cost for labor and materials is covered for 1 year from the date of receipt. If KingsBottle deems the unit not repairable, KingsBottle will use the value of your original order toward a replacement. For customer service, please contact BTO AMERICA LIMITED by e-mail ( [email protected]) . ! The limited warranty does not cover: Damage due to such things as accident, misuse, abuse, mishandling, neglect, unauthorized repair or any other cause beyond the control of the seller whether similar or dissimilar to the foregoing. Purchaser understands and acknowledges that the goods sold here are Beverage Coolers, which house wine. Purchaser assumes all the risk of using these units, including risk of spoilage, humidity variations, temperature variations, leaks, fires, water damage, mold, mildew, dryness and similar perils that may occur. ! SPECIAL NOTE: Warranty is only honored for the unit which is purchased and used in United States of America. And, if your product was purchased at any 3rd party retailer and not directly from KingsBottle, we do not offer an extended warranty policy. You MUST contact the retailer of purchase directly. In the event your retailer does not offer an extended warranty plan, we recommend you contact a third party warranty provider. However, regardless of point of purchase, all KingsBottle coolers are backed by a ONE YEAR manufacturer's warranty from date of sale. COMPRESSOR BEVERAGE COOLER www.kingsbottle.com ! 16
Similar documents
Manual-KBU-55/56/328 Carel.pages
it, aorpartially changing 1. Read all instructions before using the beverage cooler. WARNING connecting theavoid beverage cooler to the power 2. Before 6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLMLFMURM?...
More informationManual-KBU Dual Wine.pages
6FGQQWK@MJGLBGA?RCQ?JU?WQBMRFGQ – for Have doors that will self-close from a partially open position. BEFORE USING YOUR WINE COOLER qualified service technician.
More informationManual-KBU Beverage-Carel.pages
6FGQQWK@MJGLBGA?RCQ?JU?WQBMRFGQ – for Have doors that will self-close from a partially open position. BEFORE USING YOUR BEVERAGE COOLER qualified service technician.
More informationCarel Controller
position. do not store them inside any refrigerator or 1. Read CAUTION all instructions before using this refrigerator. WARNING – Have doors that will self-close from Unplug the refrigerator before...
More information