Manual-KBU Beverage-Carel.pages

Transcription

USER MANUAL
KBU-50 / 100 / 170 BEVERAGE REFRIGERATOR
—- CAREL CONTROLLER —-
KBU-50B-SS
KBU-100B-SS
KBU-170B-SS
PLEASE NOTE: EVERY TIME THE UNIT IS POWERED ON, THERE WILL BE A 6 MINUTE DELAY FOR THE COMPRESSOR TO START. COMPRESSOR BEVERAGE REFRIGERATORS
www.kingsbottle.com
!
CONTENTS
TABLE OF CONTENTS
Congratulations
Congratulations and thank you for
choosing our KingsBottle beverage
coolers . We are sure you will find your
new appliance a pleasure to use .
Before installing and operating the
beverage cooler, we recommend that
you read through this manual which
provides a description of your beverage
cooler and its functions .
To avoid the risks that are always
present when you use an electric
appliance, it is important that the
appliance is installed correctly and that
you read the safety instructions carefully
to avoid misuse and hazards .
We recommend that you keep this
instruction booklet for future reference
and pass it on to any future owners .
After unpacking the appliance, please
inspect it to verify it is not damaged. If
in doubt, do not use the appliance but
contact us or your local customer care
centre
Chapter
Contents
Page
Part I
Important Safety & Pre-Use Instructions
3
Part II
Diagram & Description of Refrigerator
4
Part III
Installation Instructions
5-6
Part IV
Temperature Setting and Refrigerator Operating
7-8
Part V
Layout & Storage
9
PART VI
Maintenance
10
Part VII
Troubleshooting Guide
11
Part VIII
Technical Data
12
Part IX
Warranty Information
12
COMPRESSOR BEVERAGE REFRIGERATORS
www.kingsbottle.com
2
+/2146#065#('6;+05647%6+105
+/2146#065#('6;+05647%6+105
+/2146#065#('6;+05647%6+105
+/2146#065#('6;+05647%6+105
PART
I IMPORTANT SAFETY INSTRUCTIONS
0LEASE¬READ¬THE¬USER¬MANUAL¬CAREFULLY¬AND¬STORE¬IN¬A¬HANDY¬
5#('6;
SAFETY
5#('6;
6.
WARNING
WARNING
WARNING
The
The refrigerator
refrigerator must
must be
be plugged
plugged into
into its
its own
own
Unplug
the cooler
before
cleaning
it, AC
or changing
theoutlet.
light
WARNING
dedicated
220-240V,
50Hz
electrical
The
refrigerator
must
be
plugged
into
its
own
dedicated 220-240V, 50Hz AC electrical
outlet.
bulb
to plug
avoid must
electric
shock
.
dedicated
220-240V,
ACinto
electrical
The
be
accessible
when
the
The
refrigerator
must
be50Hz
plugged
itsrefrigerator
ownoutlet. isis
Theclean
plugappliance
must
be
accessible
when
the
refrigerator
Never
parts
with flammable
fluids.
The
in
position.
The
plug
must
be
accessible
when
the
refrigerator
dedicated
220-240V,
50Hz
AC
electrical
outlet. is
in position.
fumes
can create a fire hazard or explosion.
inisposition.
ItThe
essential
the
power
point
is
properly
earthed
to
plug must
bepower
accessible
the refrigerator
It is unplug
essential
point the
iswhen
properly
earthed
Never
thethe
cooler
by pulling
electrical
cord as to is
ground.
Consult
a
qualified
electrician
if
you
are
It
is
essential
the
power
point
is
properly
earthed
to
position.
ground.
Consult
a qualified
electrician
if you
are unsure.
unsure.
thisin
may
damage
it. Grip
the plug firmly
and pull
straight
The symbols you will see in this booklet have these meanings:
ground.
Consult
a
qualified
electrician
if
you
are
unsure.
WARNING
Don’t
use
extension
cords
or
adapter
plugs
with
the power
pointorisadapter
properlyplugs
earthed
outItDon’t
.is essential
WARNING
use extension
cords
withtothis
this
WARNING
refrigerator.
Don’t
use
extension
cords
or
adapter
plugs
with
this
6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLAMLACPLGLEWMSPNCPQML?JQ?DCRW
ground.
Consult
a
qualified
electrician
if
you
are
unsure.
9.
Choose
a
location
for
your
cooler
that
isn’t
too
cold
.
The
refrigerator.
This
symbol
indicates information concerning your personal safety
Ifrefrigerator.
power
cord
damaged,
have
itplugs
by
ambient
temperature
should
above
. with this
WARNING
Don’t
use
extension
orbe
adapter
If the
the room
power
cord isis cords
damaged,
have 50°F
it replaced
replaced
by aa
If
the
power
cord
is
damaged,
have
it
replaced
by
a
qualified
service
technician.
10.
Stand
your
cooler
in
a
dry
place
–
avoid
areas
of
high
refrigerator.
qualified service technician.
CAUTION
qualified
service
technician.
moisture
or
humidity
.
Unplug
the
refrigerator
before
cleaning
it,
or
changing
CAUTION
IfUnplug
the power
cord is damaged,
have it replaced
by a
the
refrigerator
before
cleaning
it, or changing
CAUTION
6FGQQWK@MJGLBGA?RCQGLDMPK?RGMLMLFMURM?TMGBB?K?EGLERFC
11. Don’t
put
the
cooler
frosty electric
or
unprotected
areas
a
Unplug
the
refrigerator
before
cleaning
it, like
or changing
the
light
bulb
to inavoid
shock.
qualified
service
technician.
the
light
bulb
to
avoid
electric
shock.
?NNJG?LAC
garage
or on
the verandah
. electricby
CAUTION
the light
bulb
to
shock.
This
symbol
indicates information on how to avoid damaging the
Never
unplug
theavoid
refrigerator
pullingit,theorelectrical
?NNJG?LAC
Unplug
the
refrigerator
before by
cleaning
changing
Never
unplug
the
refrigerator
pulling the electrical
?NNJG?LAC
12. Keep
theas
cooler
out
ofdamage
direct
sunlight
. pulling
appliance
Never
unplug
the
refrigerator
by
thefirmly
electrical
cord
this
may
it.
Grip
the plug
and
the
light
bulb
to
avoid
electric
shock.
cord
as this
this
may damage
damage
it. Grip
Grip
the
plug .firmly
firmly and
and
13. Don’t
locate
the out.
cooler
near stoves,
fires orthe
heaters
cord
as
may
it.
plug
?NNJG?LAC
pull
straight
unplug
the
refrigerator
byappliance.
pulling the
TIPS
&
INFORMATION
pull
straight
out.
14. DoNever
not store
in the
vicinity
of any other
Doelectrical
not
pull
straight
out.
TIPS
&
INFORMATION
Choose
a location
for your refrigerator
that
too cold.
TIPS & INFORMATION
cord
asgasoline
this
may
it.
Grip the
plugisn’t
firmly
6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRSQCMDRFC?NNJG?LAC
store
near
or damage
any
vapors.
The
Choose
a location
location
forother
your flammable
refrigerator
that
isn’t
too and
cold.
Choose
a
for
your
refrigerator
that
isn’t
too
cold.
The
ambient
room
temperature
should
be
above
10°C.
pull
straight
out.
fumes
can
create
a
fire
hazard
or
explosion.
The
ambient
room
temperature
should
be
above
10°C.
TIPS
&
INFORMATION
The
ambient
room
temperature
should
be
above
10°C.
This symbol indicates tips and information about use of the
Stand
your
refrigerator
incooler
arefrigerator
dry
placethat
– avoid
areas
Choose
a location
for
your
isn’t too
cold.
installed
correctly,
your
should:
Stand
your
refrigerator
in a
a dry
dry
place –– avoid
avoid
areas
6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRSQCMDRFC?NNJG?LAC 15. When
Stand
your
refrigerator
in
place
areas
appliance
WARNING
of
high
moisture
or
humidity.
ENVIRONMENTAL TIPS
The
ambient
room
temperature
should
be
above
10°C.
Have
adequate
space
at
the
back
and
sides
for
air
•
of high
high moisture
moisture or
or humidity.
humidity.
ENVIRONMENTAL TIPS
TIPS
of
ENVIRONMENTAL
Don’t
put
refrigerator
in
or unprotected
areas
circulation.
(See
Page
6FGQQWK@MJGLBGA?RCQRGNQ?LBGLDMPK?RGML?@MSRCAMLMKGA?J?LB
Stand
yourthe
refrigerator
a frosty
dry place
– avoid
The
refrigerator
must5)beinplugged
its
own areas
Don’t
put
the
refrigerator
in
frosty into
or unprotected
unprotected
areas
Don’t
put
the
refrigerator
in
frosty
or
like
a
garage
or
on
the
verandah.
Be
aligned
to
the
surrounding
cupboards
.
CAMJMEGA?JSQCMDRFC?NNJG?LAC
•
of
high
moisture
or
humidity.
ENVIRONMENTAL TIPS
dedicated
220-240V,
50Hz
AC electrical outlet.areas
like
a
garage
or
on
the
verandah.
like
a
garage
or
on
the
verandah.
Have
doors
thatrefrigerator
will self-close
a partially
open
• Don’t
Keep
the must
refrigerator
out in
offrom
direct
sunlight.
put
the
frosty
or
unprotected
areas
The
be
accessible
when
the
refrigerator
is
Keepplug
the refrigerator
refrigerator
out of
of direct
direct
sunlight.
place
for indicates
later
reference.
Keep
the
out
sunlight.
This
symbol
tips and
information
about economical
and below:
position
Meanings
of
symbols
used
in
this
manual
are
shown
like
a
garage
or
on
the
verandah.
in position.
Don’t
locate
the
refrigerator
near
stoves,
fires
or
heaters.
Meanings
symbols
used
in this
manual
shown
below: 16. Please
The
symbols
will see
in this
booklet
haveare
these
meanings:
ecological
use of
ofyou
the
appliance
inspect
and
the filter near
in front
ventingfires
grill or heaters.
Don’t
locate
theclean
refrigerator
stoves,
Keep
the
refrigerator
out
of
direct
sunlight.
ItWhen
is essential
power
point
properly
earthed
to
installed
correctly,
your
refrigerator
should:
every month.
Failure
tothe
clean
will void
theiswarranty
and
6FGQQWK@MJGLBGA?RCQLCTCPRMBMRFGQ
When
installed
correctly,
your
refrigerator
should:
Meanings
of
symbols
used
in
this
manual
are
shown
below:
ground.
Consult
a
qualified
electrician
if
you
are
unsure.
–
Have
adequate
space
at
the
back
and
sides
Don’t
locate
the
refrigerator
near
stoves,
fires
or
heaters.
increase the running costs.
Please
read this user manual carefully and store in a handy
place
later
reference.
7.
placeforfor
forlater
later
reference.
place
reference
. The symbols you will see in this
The
symbols
you
will
see
in
this
booklet
have
these
meanings:
place
for
later
reference.
The
symbols
you
will
see
in
this
booklet
have
these
meanings:
booklet have these meanings:
The symbols
will see in this booklet have these meanings: 8.
place
for lateryou
reference.
5#('6;
+/2146#065#('6;+05647%6+105
5#('6;
Have
adequate
space
at page
the back
Don’t– use
extension
cords
or adapter
plugs
withsides
this
for
air
circulation
(refer
to
9). and
When
installed
correctly,
your
refrigerator
should:
for
air
circulation
(refer
to
page
9).
refrigerator.
–
Be
aligned
to
the
surrounding
cupboards.
–– Have
adequate
at the back
and sides
Be aligned
to thespace
surrounding
cupboards.
Have
will
self-close
a partially
If the–power
cord
isthat
damaged,
it9).
replaced
by a
air doors
circulation
(refer
to have
pagefrom
OR INJURY
WHEN USING YOUR APPLIANCE, FOLLOW
6FGQQWK@MJGLBGA?RCQ?JU?WQBMRFGQ
– for
Have
doors
that
will
self-close
from
a partially
open
position.
BEFORE
USING
YOUR
BEVERAGE
COOLER
qualified
service
technician.
–
Be
aligned
to
the
surrounding
cupboards.
THESE BASIC PRECAUTIONS:
open position.
CAUTION
WARNING
– Have
doors that will
self-close
from
Unplug
the refrigerator
before
cleaning
it, aorpartially
changing
1. Read
all instructions before using the beverage cooler.
WARNING
the
exterior
interior
packing.
1. Remove
open
position.
the light
bulb
to and
avoid
electric
shock.
s¬¬)F¬PRESSURISED¬AEROSOL¬CONTAINERS¬BEAR¬THE¬WORD¬
2.
DANGER or WARNING: Risk of child entrapment.
s¬¬‘flammable’
)F¬PRESSURISED¬AEROSOL¬CONTAINERS¬BEAR¬THE¬WORD¬
2. Before connecting the beverage cooler to the power
?NNJG?LAC
and/or
a smallareflame
symbol,
Child
entrapment
and suffocation
not only
problems of the
WARNING
Never
unplug the refrigerator by pulling the electrical
WARNING
‘flammable’
and/or
a
small
flame
symbol,
source,
let it stand upright for approximately 24 hours.
WARNING
do
not
store
them
inside
any
refrigerator
or
past.
Junked or abandoned appliances are still dangerous…
cord
as
this may damage it. Grip the plug firmly and
s¬¬)do
F¬PRESSURISED¬AEROSOL¬CONTAINERS¬BEAR¬THE¬WORD¬
4#4'(4+)'4#069#40+0)
not
them
inside
any
refrigerator
or
This will reduce the possibility of a malfunction in the
doif they
not store
store
them
inside
any
refrigerator
or
+/2146#065#('6;+05647%6+105
even
will
“just
sit so
in
the
garage
for
a few
freezer.
If you
do
you
mayflame
cause
andays”.
explosion.
4#4'(4+)'4#069#40+0)
pull
straight
out.
4#4'(4+)'4#069#40+0)
‘flammable’
and/or
a
small
symbol,
WARNING
This
appliance
a during
small quantity
of environmentally
TIPSyou
INFORMATION
freezer.
IfIf &
you
do
so
may
cause
an
explosion.
cooling
systemmay
fromcontain
handling
transportation.
freezer.
you
do away
so you
you
may
cause
ancooler:
explosion.
3.
Before
throw
your
oldrefrigerator
beverage
s¬¬do
7
HEN¬YOU¬DISPOSE¬OF¬YOUR¬OLD¬REFRIGERATORS¬AND¬FREEZERS¬
This
appliance
may
contain
a
quantity
of
environmentally
This
appliance
may
contain
a small
small
quantity
of
environmentally
not
store
them
inside
any
or
Choose
a
location
forwith
your
refrigerator
that
isn’t too cold.
friendly,
but
flammable,
non-synthetic
R600a
refrigerant:
s¬¬
7
Clean
the
interior
surface
lukewarm
water
using
4#4'(4+)'4#069#40+0)
3.
s¬¬remove
7
The
refrigerator
must
be
plugged
into
its
owna
Take
off
the
door.
any
doors.
Children
can
suffocate
if
they
get
friendly,
but
flammable,
non-synthetic
R600a
refrigerant:
•
friendly,
but
flammable,
non-synthetic
R600a
refrigerant:
freezer.
Ifany
youdoors.
do soChildren
you maycan
cause
an explosion.
The
ambient
room
temperature
should
be
above
10°C.
s¬¬
%
NSURE¬THAT¬THE¬TUBING¬OF¬THE¬REFRIGERANT¬CIRCUIT¬IS¬NOT¬
remove
suffocate
if
they
get
soft
cloth.
This
appliance
may
contain a50Hz
small quantity
of environmentally
remove
any
suffocate
they
dedicated
220-240V,
AC electrical
outlet.
Leave
thedoors.
ShelvesChildren
in pieces can
so that
children ifmay
notget
s¬¬
%%NSURE¬THAT¬THE¬TUBING¬OF¬THE¬REFRIGERANT¬CIRCUIT¬IS¬NOT¬
trapped
inside.
• HEN¬YOU¬DISPOSE¬OF¬YOUR¬OLD¬REFRIGERATORS¬AND¬FREEZERS¬
s¬¬damaged
s¬¬
7
during
transportation
and
installation.
Stand
your
refrigerator
in
a
dry
place
–
avoid
areas
trapped
inside.
friendly,
flammable,
non-synthetic
R600a
inside.
climb
inside
easily.
damaged
during
transportation
and
s¬¬remove
4trapped
HIS¬APPLIANCE¬CONTAINS¬INSULATION¬FORMED¬WITH¬mAMMABLE¬
Thebut
plug
must be
accessible
when
the refrigerant:
refrigerator is
damaged
during
transportation
and installation.
installation.
any
doors.
Children
can suffocate if they get
s¬4HE¬ROOM¬FOR¬INSTALLING¬APPLIANCE¬MUST¬BE¬AT¬LEAST¬M¬PER¬
of
high
moisture
or
humidity.
s¬¬
4
place
for
later
reference.
ENVIRONMENTAL
TIPS
s¬¬
%
s¬¬blowing
4HIS¬APPLIANCE¬CONTAINS¬INSULATION¬FORMED¬WITH¬mAMMABLE¬
4.
Never allow
children
to operate,
play with,by
or carefully
crawl inside
gases.
Avoid
safety hazards
trapped
inside.
8gin
ofposition.
refrigerant.
The
amount in
of frosty
refrigerant
charged in areas
the
blowing
gases.
Avoid
safety
hazards
by
carefully
The
symbols
you will
see in
this booklet
have
these meanings: s¬4HE¬ROOM¬FOR¬INSTALLING¬APPLIANCE¬MUST¬BE¬AT¬LEAST¬M¬PER¬
Don’t
putduring
the refrigerator
unprotected
damaged
transportation
and or
installation.
blowing
gases.
Avoid
safety
hazards
by
carefully
the
appliance.
8g
amount
of
refrigerant
charged
in
disposing
of
this
appliance.
It of
is refrigerant.
essential
theThe
power
point
is
properly
earthed
to the
s¬¬4disposing
8g
of
refrigerant.
The
amount
of
refrigerant
charged
in
the
appliance
can
be
found
on
the
rating
plate
on
the
appliance.
of
this
appliance.
like a garage
orfound
on the
verandah.
disposinggases.
of thisAvoid
appliance.
appliance
be
on
the
rating
plate
appliance.
ground. can
Consult
a qualified
electrician
ifon
youthe
are
unsure.
blowing
safety hazards by carefully
appliance
can
be
found
on
the
rating
plate
on
the
appliance.
s¬+EEP¬VENTILATION¬OPENINGS¬IN¬THE¬APPLIANCE¬ENCLOSURE¬OR¬
8gKeep
of refrigerant.
The amount
of direct
refrigerant
charged in the
the refrigerator
out of
sunlight.
disposing
of this appliance.
WARNING
use
orrating
adapter
this
in Don’t
the built-in
structure,
clear
obstruction.
appliance
canextension
be foundcords
on theof
plateplugs
on thewith
appliance.
Meanings of symbols used in this manual are shown below:
in Don’t
the built-in
structure,
clear
of
obstruction.
locatestructure,
the refrigerator
stoves, fires or heaters.
in refrigerator.
the built-in
clear ofnear
obstruction.
s¬$O¬NOT¬USE¬MECHANICAL¬DEVICES¬OR¬OTHER¬MEANS¬TO¬
1. The beverage cooler must be plugged into its own
When
installed
correctly,
your
refrigerator
should:
accelerate
the
defrosting
process,
other
those
If the
power
cord
is clear
damaged,
have
replaced
in
the
built-in
structure,
of obstruction.
accelerate
the
defrosting
process,
otheritthan
than
those by a
dedicated
110-115V, 50/60Hz AC electrical outlet .
accelerate
the
defrosting
process,
other
than
those
–
Have
adequate
space
at
the
back
and
sides
recommended
by
the
manufacturer.
qualified
service
technician.
2. The plug must be accessible when the cooler is in
recommended by the manufacturer.
3
CAUTION
recommended
by
the
manufacturer.
for
air
circulation
(refer
to
page
9).
s¬4HE¬ROOM¬FOR¬INSTALLING¬APPLIANCE¬MUST¬BE¬AT¬LEAST¬M
3
accelerate
the refrigerator
defrosting process,
other than
those
Unplug the
before cleaning
it, or
changing
position.
3
–
Be
aligned
to
the
surrounding
cupboards.
per
8g
of
refrigerant.
The
amount
of
refrigerant
charged
recommended
by
the
manufacturer.
the
light
bulb
to
avoid
electric
shock.
3. It is essential the power point is properly grounded .
per 8g of refrigerant. The amount of refrigerant charged
per
8g
of
refrigerant.
The
amount
of
refrigerant
charged
3
–
Have
doors
that
will
self-close
from
a
partially
in
the
appliance
can
be
found
on
the
rating
plate
on
?NNJG?LAC
Consult a qualified electrician if you are unsure .
in Never
the appliance
canrefrigerator
be found on
rating
on
unplug the
bythe
pulling
theplate
electrical
in the
appliance
can The
be found
onoftherefrigerant
rating plate
on
open position.
the
appliance.
per
8g
of
amount
charged
4. Don’t use extension cords or adapter plugs with this
the
appliance.
cord
as refrigerant.
this may damage
it. Grip
the plug firmly
and
the
appliance.
WARNING
in the
appliance
can be found on the rating plate on
cooler .
pull
straight
out.
TIPS & INFORMATION
theChoose
appliance.
If the power cord is damaged, have it replaced by a
5.
a location for your refrigerator that isn’t too cold.
qualified service
technician
. flame symbol,
‘flammable’
and/or
a small
TheWARNING
ambient room temperature should be above 10°C.
do not store them inside any refrigerator or
4#4'(4+)'4#069#40+0)
Stand your refrigerator in a dry place – avoid areas
freezer. If you do so you may cause an explosion.
This appliance
may contain
a small quantity of environmentally
of high moisture
or humidity.
ENVIRONMENTAL
TIPS
s¬¬7HEN¬YOU¬DISPOSE¬OF¬YOUR¬OLD¬REFRIGERATORS¬AND¬FREEZERS¬
friendly,
but
flammable,
non-synthetic
R600a
refrigerant:areas
Don’t put the refrigerator in frosty
or unprotected
remove any doors. Children can suffocate if they get
s¬¬
%
like
a
garage
or
on
the
verandah.
trapped inside.
!
damaged
transportation
and sunlight.
installation.
Keep theduring
refrigerator
out of direct
s¬¬4HIS¬APPLIANCE¬CONTAINS¬INSULATION¬FORMED¬WITH¬mAMMABLE¬
Meanings
symbols
used
in this
manualbyare
shown below:
blowing of
gases.
Avoid
safety
hazards
carefully
locate theThe
refrigerator
stoves,charged
fires or heaters.
8gDon’t
of refrigerant.
amount ofnear
refrigerant
in the
disposing of this appliance.
When
installed
correctly,
your
refrigerator
should:
appliance
can
be
found
on
the
rating
plate
on
the
appliance.
– Have adequate space at the back and sides
www.kingsbottle.com
3
for air
circulation
(refer
to page 9).
in the built-in
structure,
clear
of obstruction.
– Be aligned to the surrounding cupboards.
– Have
doors that process,
will self-close
partially
accelerate
the defrosting
otherfrom
thanathose
open position.
recommended
by the manufacturer.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK,
FEATURES
PART II
DIAGRAM & DESCRIPTION OF REFRIGERATOR
1 Control board
2 Housing
3 Ventilation DC Fan
4 Shelf
5 Front grill
6 Door hinge
7
8
9
Controller
Door
Adjustable stand feet
YOUR REFRIGERATOR ALSO INCLUDES TWO KEYS TO OPERATE THE ROUNDED LOCKING
MECHANISM WHICH IS SHOWN AT THE LOWER CENTRE POSITION OF THE DIAGRAM.
www.kingsbottle.com
4
INSTALLATION
PART III
INSTALLATION INSTRUCTIONS
CUTOUT DIMENSION ILLUSTRATED
KBU-170 SERIES
23.54”W x 26.97”D x 71.69”H
(598W x 685D x 1821H mm)
Included stand height 0.98”(25mm)
KBU-100 SERIES
23.54”W x 26.97”D x 55.43”H
(598W x 685D x 1408H mm)
Included stand height 0.98”(25mm)
MODEL
WIDTH
DEPTH
HEIGHT
INCLUDED STAND HEIGHT
KBU-50
23.42”
595mm
23.62”
600mm
33.86”
860mm
0.79”
20mm
KBU-100
23.54”
598mm
26.97”
685mm
55.43”
1408mm
0.98”
25mm
KBU-170
23.54”
598mm
26.97”
685mm
71.69”
1821mm
0.98”
25mm
KBU-50 SERIES
23.42”W x 23.62”D x 33.86”H ( 595W x 600D x 860H mm )
Included stand height 0.79” (20mm)
NOTE
These front-venting models can be built in to cabinetry.
Builders should allow an additional 1/2” either side of the
unit, plus 1” behind the unit and 1/2” on top. These
additional spaces allow units to be placed in position easily,
and without power cords being damaged. This also allow
hot air that is vented from the front to rise quickly and clear
the cool air intake manifold. These clearances help to keep
power consumption to a minimum and prolong the life of
your refrigerator
!
www.kingsbottle.com
5
INSTALLATION
PART III
INSTALLATION INSTRUCTIONS
INSTALLING YOUR BEVERAGE COOLER
1. Move the unit into its final position .
2. If the unit is not tilting back, minor adjustments can be made to the leveling legs.
3. Compare the alignment of the appliance to the surrounding cupboard . The top of the appliance should be level from side to side
(see diagram below) .
4. If the unit now rocks from one corner to the opposite rear corner, this means that the floor is uneven. You may need to put some
packing under the ridge to the rear of the appliance . You could use thin pieces of solid material such as thin board, vinyl floor tiles or
laminate .
5. You may now need to fine tune the installation by repeating steps 2, 3 and 4 .
6. Wipe off any dust that has accumulated during shipping and clean following the directions in Part VI ( Care & Maintenance)
7. Plug the appliance into the power point. Don’t use a double adaptor or extension cord .
8. It is recommended that you let the unit for rest an hour or two before you put any beverages in it . This will confirm that it is operating
correctly and make the conditions appropriate for beverage storage .
Congratulations! You have successfully installed your beverage cooler.
DOOR LOCK
This unit comes with an optional key lock. The keys are located inside the plastic bag that contains the user manual. To lock the door,
simply reverse the operation making sure the metal pin is engaged completely. Then remove the key and place it in a secure place for
safekeeping. To unlock the door, insert the key into the lock and turn counterclockwise.
www.kingsbottle.com
6
OPERATION
PART IV
OPERATING YOUR REFRIGERATOR
This KingsBottle Refrigerator series comes with the worlds best quality controller from CAREL. Before using your Refrigerator, please read these
instructions carefully .
ADJUST TEMPERATURE
1. Press the “SET / MUTE” button for more than 3 sec. ,the display shows the parameter
code “ST/VALUE/PS/0” , 0 is the PASSWORD.
2. Release the button when it shows ST/0.
3. Use the “UP” and “DOWN” buttons to adjust the temperature.
4. Press SET / MUTE button, or if no button is pressed for 5 seconds, the change of
setting is saved and the DISPLAY will show the actual temperature.
KEYBOARD:
UP/POWER
DISPLAY:
1. Increase the value;
2. Holding the button for at least 3
seconds, powers the unit ON or OFF.
1.Decrease the value;
2. Holding the button for half a second
turns the interior light ON or OFF.
DOWN/LIGHT
1. Use SET after selecting values with the
up and down arrows
2. alarm mute button.
SET/MUTE
1. COMPRESSOR
2. FAN
3. DEFROST
4. ALARM
5. FIGURE
!
www.kingsbottle.com
7
OPERATION
ON
Compressor
activation
request
TABLE OF ALARMS
OFF
ALARM CODE
DESCRIPTION
LO
low temperature alarm
HI
high temperature alarm
E0
probe 1 error=control
E1
probe 2 error=defrost
E3
enter defrost status d12 twice continuously
dF
defrost running
dor
open door alarm
EE
unit parameter error
EF
+/2146#065#('6;+05647%6+105
5#('6;
operating parameter erro
WARNING
The refrigerator must be plugged into its own
dedicated 220-240V, 50Hz AC electrical outlet.
NOTE: The desired temperatures may fluctuate depending on whether theThe
interior
is ON
or OFF, the ambient
temperature,
pluglight
must
be accessible
when the
refrigeratortheis
place
foroflater
location
unit reference.
and the orientation of the bottles. The display is just a guide,
guided by how cold your drinks are at consumption.
in be
position.
The
symbolsunits
you go
willinto
seedefrost
in thismode
booklet
these
meanings:
Remember
andhave
this will
show
a higher display, it’s only for short periods and doesn’t have time to effect drink
It is essential the power point is properly earthed to
temperature. In general once unit has settled it will keep products within 5°F ( 2°C ) of the set temp easily in temperatures up to and
ground. Consult a qualified electrician if you are unsure.
beyond 100°F ( 38°C ) . WARNING
Don’t use extension cords or adapter plugs with this
refrigerator.
CAUTION
Unplug the refrigerator before cleaning it, or changing
the light bulb to avoid electric shock.
?NNJG?LAC
be automatically
and eachby
compartment
return to the
1. In the event of a power interruption, all previous temperature settings willNever
unplug thesaved
refrigerator
pulling thewill
electrical
previous temperature setting.
cord as this may damage it. Grip the plug firmly and
6 minutes
2. If the unit is unplugged, loses power, or is turned off, you must wait overpull
straightbefore
out. restarting. Within this 6 minutes, compressor
TIPS itself
& INFORMATION
protect
and will not start even power ON again
Choose a location for your refrigerator that isn’t too cold.
3. When you use the beverage cooler. for the first time or restart the beverage cooler after having been shut off for a long time, there will be a
The ambient room temperature should be above 10°C.
few degrees variance between the temperature you select and the one indicated on the LED readout for the first few hours of operation.
Stand temperature.
your refrigerator in a dry place – avoid areas
After a few hours of operation, the temperature will normalize to the displayed
of high moisture or humidity.
ENVIRONMENTAL TIPS
Don’t put the refrigerator in frosty or unprotected areas
like a garage or on the verandah.
Keep the refrigerator out of direct sunlight.
Don’t locate the refrigerator near stoves, fires or heaters.
When installed correctly, your refrigerator should:
for air circulation (refer to page 9).
www.kingsbottle.com
8
– Have doors that will self-close from a partially
open position.
WARNING
STORAGE
cabinet’s original configuration in any way, be sure to ask your dealer fo
PART V
LAYOUT AND STORAGE
YOUR CABINET WAS DESIGNED TO STORE A MAXIMUM NUMBER OF BOTTLES SECURELY. WE RECOMMEND THAT YOU
shelving
OBSERVE THE TIPS BELOW TO OPTIMIZE LOADING.
1.
Disperse your bottles even so as not to concentrate weight in any one area. Also, be careful that your bottles do not touch either the
3.
4.
A cooler that is full and has nice allowance for air movement will work more efficiently.
Never try to adjust shelf with bottles still on it.
back
of thethe
cabinet shelving
or the step at the bottom.
eer bottles
on
any way you like, lay down or upright.
2. Also make sure that bottles are not all grouped together either at the top or bottom of the cabinet.
ht per shelf: 25kgs
How to use your shelving
helving, clips
can be moved, place ‘top’ part of clip in first then force botto
• You can put the beer bottles on the shelving any way you like, lay down or upright.
•
Max Weight per shelf: 55 lbs ( 25kgs )
• To adjust shelving,
m loose, remove
andclips‘expand
the
width
ofthenopening
on
this
allow
can be moved, place
‘top’ part
of clip in first
force bottom part up.
If clipsclip,
seem loose,
removewill
and
‘expand the width of opening on clip, this will allow it to fit better.
PLEASE NOTE
Before modifying your cabinet’s original configuration in any way, be sure to ask your dealer for advice.
7
www.kingsbottle.com
!
9
MAINTENANCE
+/2146#065#('6;+05647%6+105
5#('6;
WARNING
The refrigerator must be plugged into its own
dedicated 220-240V, 50Hz AC electrical outlet.
PART
VI
CARE AND MAINTENANCE
The plug must be accessible when the refrigerator is
place for later reference.
in position.
The symbols you will see in this booklet have these meanings:
CLEANING
YOUR BEVERAGE COOLER
It is essential the power point is properly earthed to
ground. Consult a qualified electrician if you are unsure.
WARNING
Don’t use extension cords or adapter plugs with this
refrigerator.
BEFORE CLEANING: Turn off the power, unplug the appliance, and remove all items including all shelves.
• Wash the inside surfaces with warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda with a
quart of
water.
CAUTION
Unplug the refrigerator before cleaning it, or changing
• Wash the shelves with a mild detergent solution.
the light
to avoid
electric shock.
or bulb
any electrical
parts.
• Wring excess water out of the sponge or cloth when cleaning area of the controls,
?NNJG?LAC
refrigerator
pulling the electrical
well andunplug
wipe drythe
with
a clean softby
cloth.
• Wash the outside cabinet with warm water and mild liquid detergent. Rinse Never
cord
as this
may damage
Grip the
plug firmly
and
Oil with
a clean
rag, to allit.
exposed
Stainless
Steel
• After installation, we recommend that owners apply a thin layer of Olive
areas. This should then be polished in and buffed off with another clean ragpull
to astraight
non-oily out.
finish. This process will aid protection against
TIPS & INFORMATION
dirt and other corrosive contaminants, by providing a temporary food-safe shield.
TheaOlive
Oil layer
also makes
later polishing
Choose
location
for your
refrigerator
that isn’t and
too cold.
removal of fingerprints easier. This process should be repeated frequently every
months
. ALLtemperature
stainless steel
can rust,
it is a myth
that
The 3-4
ambient
room
should
be above
10°C.
stainless steel doesn’t rust.
Stand your refrigerator in a dry place – avoid areas
of high moisture or humidity.
ENVIRONMENTAL TIPS
POWER
FAILURE
Don’t put the refrigerator in frosty or unprotected areas
Most
power failures are corrected within a few hours and should not affect thelike
temperature
of your
if you minimize the number of
a garage
or onappliance
the verandah.
times the door is opened. If the power is going to be off for a longer period of time,
to take the
stepssunlight.
to protect your
Keepyou
theneed
refrigerator
outproper
of direct
contents.
Don’t locate the refrigerator near stoves, fires or heaters.
When installed correctly, your refrigerator should:
VACATION
TIME
Short vacations: You may leave the beverage cooler operating during vacations of less than three weeks.
for air circulation (refer to page 9).
Long 6FGQQWK@MJGLBGA?RCQ?JU?WQBMRFGQ
vacations: If the appliance will not be used for several months, remove all items and turn off the appliance. Clean and dry the interior
thoroughly. To prevent mold growth, leave the door open slightly, blocking it open if necessary.
– Have doors that will self-close from a partially
open position.
MOVINGWARNING
YOUR BEVERAGE COOLER
1. Remove all items.
2. Securely tape down all loose items (shelves) inside your appliance.
‘flammable’ and/or a small flame symbol,
WARNING
3. Turn the adjustable leg up to the base to avoid damage.
notthe
store
them inside any refrigerator or
4. doTape
door shut.
4#4'(4+)'4#069#40+0)
youappliance
do so you
cause
anupright
explosion.
5. freezer.
Be sureIfthe
staysmay
secure
in the
position during transportation.
Alsomay
protect
the outside
the appliance
with a
This appliance
contain
a smallofquantity
of environmentally
s¬¬7blanket
or similar item.
friendly, but flammable, non-synthetic R600a refrigerant:
remove any doors. Children can suffocate if they get
s¬¬%NSURE¬THAT¬THE¬TUBING¬OF¬THE¬REFRIGERANT¬CIRCUIT¬IS¬NOT¬
damaged during transportation and installation.
s¬¬4HIS¬APPLIANCE¬CONTAINS¬INSULATION¬FORMED¬WITH¬mAMMABLE¬
1. The beverage cooler should be located in the coolest area of the room,
away from heat producing appliances, and away from direct
blowing gases. Avoid safety hazards by carefully
of refrigerant.
The amount
of refrigerant
charged
in the
sunlight. Ventilation at rear also helps a lot with energy usage, so create8g
a positive
air flow where
possible,
although with
this range
they
disposing of this appliance.
appliance can be found on the rating plate on the appliance.
are designed to be fully built in.
2. When you are not using fridge during weekdays etc. it is recommended
to set the temp at a higher level, so set at 46°F ( 8°C ) during
in thedrinks
built-in
periods of non usage, this will not only mean less run time, it also still keeps
at astructure,
temp thatclear
won’t of
be obstruction.
spoiled. It saves energy also
which these days is a growing concern for most households.
3. Keep the cooler stocked, an empty cooler will run longer, believe it or not.
accelerate the defrosting process, other than those
recommended by the manufacturer.
s¬4HE¬ROOM¬FOR¬INSTALLING¬APPLIANCE¬MUST¬BE¬AT¬LEAST¬M3
per 8g of refrigerant. The amount of refrigerant charged
in the appliance can be found on the rating plate on
the appliance.
trappedSAVING
inside. TIPS
ENERGY
www.kingsbottle.com
10
TROUBLESHOOTING GUIDE
PART VII
PROBLEM
Refrigerator does
not operate
Refrigerator is not
cold enough; can
not cool down to
the preset temp.
TROUBLESHOOTING GUIDE
POSSIBLE CAUSE
1. Not plugged in
2. The appliance is turned OFF at the control panel
3. The circuit breaker has tripped or a fuse has blown out
Solution
Press ON/OFF
Check and make sure the power plug is well connected
Ask an engineer for help
Compressor does not start
ask an engineer for help / check the connection of the compressor
Compressor self-protected and has stopped operating
The ambient temperature is too high ( over 38C degree Celsius)
The air venting is not smooth, check that the air duct is not blocked
Fan operates slowly or is faulty and has stopped operating.
The door is not closed completely, or the door opened too long
The compressor, or its components are faulty
Fans stop working or operate at low speed
Evaporator ices up
Door is not closed properly
Compressor starts
and stops
frequently
The light does not
work.
Ask an engineer for help. Power the refrigerator ON and OFF. Check the
fan and whether the voltage is normal. If the voltage is normal, then the
fan should be damaged
Turn OFF the refrigerator for one hour and open the door. The ice on the
evaporator will melt. Check the door seal for any air gaps.
Check the door lock, shelves, or other objects, make sure door is well
closed.
Check the rubber seal for any air gaps.
Check the door hinges, make sure they are not loose
Condenser is dusty
Wash and clean the condenser
Cooling system faulty (Gas leakage or blockage)
The door gasket does not seal properly.
Use low heat on a hair dryer to make the door seal take shape.
The sensor connection is wrong.
Read the wiring diagram to make the correct connection of sensor
The sensor is faulty.
Replace with a new sensor
The door is opened too often.
Reduce the times / frequency of door openings.
Not plugged in, or the light button is “OFF”.
Light itself faulty.
Check and make sure the light button is ON, or ask an engineer for help.
The stand feet is not leveling, vibrations lead to noise
Adjust the stand feet and ensure they are level.
Copper pipe hits other objects and makes noise
Gently adjust the position of the pipe.
The Refrigerator
When the compressor shuts down or starts, it is normal for
seems to make too noise from the vibrations generated by the internal moving
Take no action
much noise.
parts due to inertia.
A liquid plumbing noise may come from the flow of the
refrigerators gases, which is normal. As each cycle ends, you Take no action
may hear gurgling sounds
The door will not
close properly.
Door is blocked by the door lock, shelves, or other objects.
Remove the barrier
Door sealing rubber is deformed
Repair or replace the rubber seal
Door hinges are not loose.
Adjust and fasten the hinges.
Outlet / suction outlet blockage
Remove the barrier
Fans stop working or operate at low speed.
Ask an engineer for help. Power the refrigerator ON and OFF. Check the
fan and the voltage. If the voltage is normal, the fan may be damaged.
The door gasket does not seal properly;
or door is opened too often
Gas leakage or cooling system blockage
Ambient temperature is too high, or direct sunshine
Operating conditions need to be improved
Front grill outlet / suction outlet blockage
Remove the barrier
Fans stop working or low speed operating
Ask engineer for help, power on the refrigerator, check the fan whether
the voltage is normal or not. If the voltage is normal, the fan should be
damage
Ambient humidity is high
Use a soft cloth to clean the water
Door is opened too often
Reduce the times / frequency of door opening.
The door gasket does not seal properly
Ice up
External cabinet
seems too hot
Water drop on
glass door
www.kingsbottle.com
11
TECHNICAL DATA
PART X
TECHNICAL DATA
MODEL NO.
KBU-170B-SS
KBU-100B-SS
KBU-50B-SS
14.30 CF ( 405 Liter )
10.88 CF ( 308 Liter)
5.37 CF ( 152 Liter )
compressor with air-circulated fan
cooling
cooling
cooling
CLIMATE TYPE
N
N
N
ELECTRICITY PROTECTION
GRADE
I
I
I
110-115V/50-60HZ
110-115V/50-60HZ
110-115V/50-60HZ
200W
190W
140W
32 - 100 °F
32 - 100 °F
32 - 100 °F
34-46 °F
34-46 °F
34-46 °F
NET WEIGHT
286.60 lbs (130 KGS)
198.41 lbs (90 KGS)
112.43 lbs (51 KGS)
GROSS WEIGHT
310.85 lbs (141 KGS)
224.87 lbs (102 KGS)
121.25 lbs (55 KGS)
23.54”W x 26.97”D x 71.69”H
( 598W x 685D x 1821H mm )
23.54”W x 26.97”D x 55.43”H
( 598W x 685D x 1408H mm )
23.42”W x 23.62”D x 33.86”H;
595W x 600D x 860H mm )
VOLUME
TYPE OF COOLING
NOMINAL VOLTAGE/
FREQUENCY
RATED POWER(W)
AMBIENT TEMPERATURE
TEMPERATURE RANGE
DIMENSION
PART IX
WARRANTY INFORMATION
Please speak to your Retailer before calling BTO AMERICA LIMITED (also known as KingsBottle) if you did not purchase your beverage cooler directly
from BTO AMERICA LIMITED
Limited warranty – If your refrigerator is not operating, KingsBottle reserves the right to repair or replace the refrigerator. KingsBottle may request the
consumer to contact a local refrigeration company to service the refrigerator. All cost for labor and materials is covered for 1 year from the date of receipt. If
KingsBottle deems the unit not repairable, KingsBottle will use the value of your original order toward a replacement. For customer service, please contact
BTO AMERICA LIMITED by e-mail ( [email protected]) .
The limited warranty does not cover: Damage due to such things as accident, misuse, abuse, mishandling, neglect, unauthorized repair or any other
cause beyond the control of the seller whether similar or dissimilar to the foregoing. Purchaser understands and acknowledges that the goods sold here are
beverage coolers, which house beer and other beverages. Purchaser assumes all the risk of using these units, including risk of spoilage, humidity variations,
temperature variations, leaks, fires, water damage, mold, mildew, dryness and similar perils that may occur.
SPECIAL NOTE: Warranty is only honored for the unit which is purchased and used in United States of America. And, if your product was purchased at
any 3rd party retailer and not directly from KingsBottle, we do not offer an extended warranty policy. You MUST contact the retailer of purchase directly.
In the event your retailer does not offer an extended warranty plan, we recommend you contact a third party warranty provider. However, regardless of
point of purchase, all KingsBottle coolers are backed by a TWO YEAR manufacturer's warranty from date of sale.
COMPRESSOR BEVERAGE REFRIGERATOR
www.kingsbottle.com
!
12

Manual-KBU Beverage-Carel.pages

Transcription

Similar documents

Manual-KBU-55/56/328 Carel.pages

Manual-KBU650 Carel.pages

Manual-KBU Dual Wine.pages

Carel Controller

Replacing Norcold N300.3 with Dometic CR-110 Refrigerator

View PDF File - ConcessionStands.com

PSA News - Professional Service Association

Kegerator - RH Peterson Co.

12/01/09 RM2351 RM2354 RM2451 RM2454 RM2551

GXSF30H – GE SmartWater™ Water Softening System

rotating belgian waffle maker USER GUIDE