Technical information - TopTronic E online

Technical information
Installation instructions
TopTronic® E online
Hoval TopTronic® E remote connection
Subject to modifications
|
4 212 588 / 04 - 09/15
EN
TABLE OF CONTENTS
1.
Important notes........................................................................................................................................ 3
2.
LED lights................................................................................................................................................. 4
3.
Bus terminating resistors........................................................................................................................ 5
1.1
1.2
Intended use.........................................................................................................................................................................3
Explanation of the symbols.................................................................................................................................................3
4.Commissioning........................................................................................................................................ 6
4.1
4.1.1
Commissioning (via commissioning wizard)......................................................................................................................6
Procedure for setting parameters.......................................................................................................................................6
5.TopTronic® E online.................................................................................................................................. 9
2
4 212 588 / 04
IMPORTANT INFORMATION
1.
1.1
Important notes
1.2
Intended use
The TopTronic® E gateway is the connection point between the Internet and the Hoval heat generator.
The gateway must be installed according to the “Technical Information Assembly / TopTronic® E Online”, after
which registration of the plant at www.hovaldesk.com is
performed using this document.
The gateway enables users to access and operate their
Hoval heating system via smartphone and tablet PC from
home or while travelling.
Explanation of the symbols
Information:
Provides important information.
Description of an activity instruction.
Result of the activity instruction.
www
www.hovaldesk.com
Fig. 01
Access is by way of the Hoval server with a free app.
4 212 588 / 04
3
TECHNICAL INFORMATION
2.
LED lights
For commissioning it is important to know what status
the gateway is currently in. The LEDs indicate the current
status for this purpose.
The LED electrical power supply is green, all other LEDs
are dark.
-- Gateway is in boot status, i.e. the operating system is
starting up - can take up to 60 seconds
-- WLAN aerial (optional) is supplied with voltage (green
LED (4) on WLAN aerial lights up)
4
3
2
1
Fig. 02
1
LED left “power supply”
• Electrical power supply via CAN bus or external supply
2
LED middle “CAN bus”:
• Connection setup to CAN bus
• Connection to CAN bus established
• No connection to the CAN bus
3
LED right “Network”
• No connection to server
→ Occurs while establishing connection to the LAN network
→ Occurs during initialisation in the WLAN (green LED on
WLAN aerial flashes) - can take up to 60 seconds
→ Otherwise check the settings on the gateway
• Connection setup to the server - can take up to 30 seconds
• Connection to server established
• Data logging on USB active
4
Green
Flashing blue
Blue
Red
Red
Flashing red
Blue
Flashing cyan
4 212 588 / 04
Hardware-Systemübersicht
INSTALLATION
3.
Bus terminating resistors
Room control
module easy
The bus terminating resistors must be activated on the
devices that are furthest apart from one another.
It is best to activate the terminating resistor on
the heat generator and on each bus station
(usually room control module or gateway) that
is installed furthest away from it.
Room control
module comfort
Gateway
Control module
e
nc
ta
is h)
d
t
t g
es en
ng e l
Lo abl
(c
Hoval CAN bus
Busebene
Base module heat generator
ReglerModule
erweiterung
RS485
Terminating
resistor
Modul-
Basic
module
Modul
Erweiterung
Heating circuit
module
Modul
Erweiterung
Heizkreis
Fig. 03
© Hoval / Nov-14
Solar
Modul
Modul
Erweiterung
Universal
Modul
Erweiterung
Universal
Activate
Modul terminating Modul
Erweiterung
Erweiterung
resistors
Modul
Erweiterung
Universal
Universal
Funktionsautomaten
Buffer
module
Universal
Fig. 06
If the components of the bus system are
exclusively fitted in the heat generator, there
is no need to activate the bus terminating
Regelsystem TopTronic® E
resistors!
Room control module (RBM)
Terminating
resistor
Fig. 04
Gateway
Terminating
resistor
Fig. 05
4 212 588 / 04
5
COMMISSIONING
4.
Commissioning
1. Use “Edit” to edit the first function
The settings described below can be performed using the commissioning wizard on
the control module of the heat generator.
Setup - Gateway
TTE - GW4 / General gateway
4.1
Commissioning (via commissioning wizard)
The following section only describes the settings for commissioning the gateway (TopTronic® E online) on the
commissioning wizard.
The setting for the system is described in the commissioning instructions “TopTronic® E Basic Module Heat
Generator”.
4.1.1 Procedure for setting parameters
After the basic settings under “General”, all other function
groups (“heat generator”, “heating circuits”, “hot water”,
“buffer”, “setup gateway”, etc.) are accessed using the
arrow symbol (1, Fig. 07).
Buffer
1
Buffer
TTE - PS 15 / Buffer
2
Fig. 07
Using “Edit” (2, Fig. 07) it is possible to carry out the most
important specific parameter settings (sample screen
Fig. 08). The parameters are divided into the corresponding function group and function with the specification on
which module (address) the functions are located.
6
1.
Fig. 08
Set the following parameters here:
Internet access
-- Network – when the gateway is connected LAN
-- WLAN – when the WLAN aerial is connected to the
gateway
Threshold global radiation in W/m2
-- The global radiation to be expected is only sent after
registration on the server and the correct address has
been entered for the plant.
-- If the set threshold is exceeded, it is possible to respond to it in the individual circuits.
DHCP
-- Yes (factory setting) – the gateway automatically obtains an IP address in the network
-- No – additional settings stated below must be made
to integrate the gateway into the network
IP address
-- If DHCP is YES, no setting is required
Subnet mask
-- If DHCP is YES, no setting is required
Default gateway
-- If DHCP is YES, no setting is required
Use IP address
-- If changes have been made to the above settings, the
change must be activated using this parameter
Following that, the gateway is restarted automatically.
4 212 588 / 04
COMMISSIONING
2. Back to the starting screen (Fig. 07)
Setup - Gateway
4.
Connection status
-- Displays the status of the WLAN connection to the
server
Signal quality
-- Displays the quality of the WLAN connection
TTE - GW4 / General gateway
3.
WLAN
Available WLAN
TTE - GW4 / Available WLAN
Fig. 09
3. Scroll to next function until all functions have been
edited,
4. Scroll to next function group, for more information see
the “TopTronic® E Basic Module H-Gen” commissioning instructions
All functions of a function group must be edited before it is permitted to scroll to the next
function group!
1.
Fig. 12
Displays all available WLAN networks to which the gateway can be connected.
WLAN
Settings
TTE - GW4 / Settings
Status - Gateway
TTE - GW4 / General gateway
1.
1.
Fig. 10
GW version
-- Software status of the gateway
Connection to server
-- A functioning connection to the service indicates
whether the settings are correct.
Fig. 13
-- WLAN password
-- Use WLAN change → still enter password
Following that, the gateway is restarted automatically.
WLAN
WLAN - information
TTE - GW4 / Information
1.
Fig. 11
4 212 588 / 04
7
COMMISSIONING
5. Select Restart and confirm with “OK”.
The restart can take a few minutes.
6. Check lamps
Fig. 14
Both LED symbols light up blue if the TopTronic® E gateway is connected to the Internet.
8
4 212 588 / 04
COMMISSIONING
5.
TopTronic® E online
Registration of the plant is possible on a PC using a current browser system.
For registration, it is necessary to have the ID number of
the gateway and the corresponding password supplied
with the gateway.
Use an Internet browser to call up the
“www.hovaldesk.com” page.
Click on “Register”.
2
Choose “Plant owner” and click on the arrow >.
3
Enter the ID number (included in the scope of delivery of the TopTronic® E online).
Enter the password.
4
5
xxxxxxxxxxxxx
xxxxxxxxxxxxx
Click on the arrow >.
6
Enter your name and e-mail address in the next
window (User detail).
Click on the arrow >.
You receive a message to your e-mail address.
Open the link in your message and edit your user
account. Therefore, enter your e-mail address,
password and password repetition.
Click on the arrow >.
Enter your data in the following windows. Click
on “Completion of registration”. The registration is
complete now.
Now you have the possibility of logging in under
“www.hovaldesk.com” with your mobile phone using the Hoval “TopTronic App” or on a PC, tablet
PC or laptop using a browser and of monitoring
and controlling your heating system.
4 212 588 / 04
9
Conservation of Energy - Protection of the Environment