mdb-1402 mar. 18, 2014 revisions date drawn by sheet title project

Transcription

PLUMBING GENERAL NOTES
I. GENERAL REQUIREMENTS:
IV. COORDINATION:
1.
PLUMBING CONTRACTOR IS TO FURNISH AND PAY FOR ALL LABOR, MATERIAL,
EQUIPMENT, PERMITS & FEES REQUIRED FOR THE COMPLETE INSTALLATION OF ALL
SYSTEMS IN THIS SECTION OF WORK.
1.
BEFORE BEGINNING WORK INVERT ELEVATIONS SHALL BE ESTABLISHED. PC IS TO
ENSURE PROPER SLOPES OF ALL WASTE AND STORM PIPING CAN BE MAINTAINED,
CONTACT ENGINEER IMMEDIATELY IF PROBLEM/ISSUE IS DISCOVERED.
2.
ALL WORK IS TO BE PERFORMED IN ACCORDANCE WITH NC PLUMBING CODE
AND ALL OTHER APPLICABLE CODES. PC IS TO COORDINATE W/ G.C. IN
REGARDS TO PROJECT TIMELINE, WORK HOURS, AS WELL AS ANY BONDING OR
INSURANCE REQUIREMENTS.
2.
P.C. TO COORDINATE LOCATION OF ALL ROOF PENETRATIONS W/ ROOFING
CONTRACTOR & MECHANICAL CONTRACTOR. P.C. & M.C. TO COORDINATE TO
ENSURE NO PLUMBING VENTS ARE LOCATED WITHIN 10' OF ANY OUTSIDE AIR
INTAKES.
ALL PLUMBING FIXTURES AND PLUMBING SYSTEM EQUIPMENT SHALL BE PROVIDED
COMPLETE WITH ALL ACCESSORIES, HANGERS, VALVES, STOPS, TAILPIECES, TRAPS,
FAUCETS, STRAINERS, ETC REGARDLESS OF PRESENCE ON PLANS. SEE FIXTURE
SCHEDULE.
3.
P.C. TO COORDINATE W/ G.C. AND ARCH PLANS TO ENSURE NECESSARY
BACKING/SUPPORTS ARE INSTALLED TO ALLOW INSTALLATION OF PLUMBING
FIXTURES.
4.
THE PLUMBING CONTRACTOR SHALL COORDINATE CLOSELY WITH ALL OTHER
TRADES TO AVOID CONFLICT AND ENSURE OTHER TRADES PROVIDE MEASURES TO
ACCOMMODATE PLUMBING WORK (I.E. ACCESS DOORS, SLAB/WALL/ROOF
OPENINGS, ELECTRICAL CONNECTIONS, ETC)
3.
4.
ALL EQUIPMENT, MATERIALS AND INSTALLATION SHALL BE GUARANTEED TO BE
FREE OF DEFECTS FOR A PERIOD OF ONE (1) YEAR AFTER FINAL ACCEPTANCE OF
WORK OR IN ACCORDANCE WITH THE MANUFACTURER'S STANDARD
GUARANTEE, IF LONGER. EXISTING EQUIPMENT IS EXCLUDED FROM WARRANTY
REQUIREMENT.
5.
THESE DRAWINGS ARE DIAGRAMMATIC AND SHOW GENERAL LOCATION AND
ARRANGEMENT OF ALL MATERIALS AND EQUIPMENT. THE DRAWINGS SHALL BE
FOLLOWED AS CLOSELY AS BUILDING CONSTRUCTION AND ALL OTHER WORK
WILL PERMIT.
6.
DO NO SCALE DRAWINGS FOR MEASUREMENT.
7.
INFORMATION GIVEN IN SCHEDULES INCLUDES BOTH DESCRIPTION OF PRODUCT
AND MANUFACTURER'S MODEL #. IF CONFLICT IS PRESENT BETWEEN DESCRIPTION
AND MODEL #, EQUIPMENT DESCRIPTION SHALL TAKE PRECEDENT. IN CASE OF
CONFLICT BETWEEN THE PLANS AND NOTES/SPECIFICATIONS OR CONFLICT
BETWEEN INFORMATION PRESENTED ON THE PLANS OR IN THE
NOTES/SPECIFICATIONS, THEN THE MOST RESTRICTIVE SHALL TAKE PRECEDENT.
5.
6.
PIPING SHOULD BE COORDINATED WITH ALL STRUCTURAL FOOTINGS AND
FOUNDATIONS. PIPE SHOULD BE OFFSET TO AVOID CONTACT WITH FOOTINGS
AND FOUNDATION WALLS. IF PIPING MUST RUN UNDERNEATH A FOOTING OR
THROUGH A FOUNDATION WALL, THE PIPE MUST BE INSTALLED WITH A RELIEVING
ARCH OR IN A PIPE SLEEVE.
P.C. TO REFER TO ARCHITECTURAL DRAWINGS FOR MOUNTING HEIGHTS OF
PLUMBING FIXTURES.
V. EXECUTION:
1.
P.C. TO FOLLOW MANUFACTURER'S INSTRUCTIONS WHEN INSTALLING PLUMBING
EQUIPMENT. ENSURE REQUIRED MAINTENANCE ACCESS AND CLEARANCES ARE
MAINTAINED. IF CONFLICT EXISTS BETWEEN THESE PLANS AND MFG INSTRUCTIONS
CONTACT ENGINEER.
8.
BEFORE BID PC IS RESPONSIBLE FOR CLARIFYING W/ G.C. ANY CONFUSION IN
REGARDS TO RESPONSIBILITY OF WORK TO BE PERFORMED OR MATERIALS TO BE
PROVIDED. THE SUBMITTAL OF THE BID BY THE CONTRACTOR WILL BE HELD AS
PROOF THAT THE CONTRACTOR UNDERSTANDS THOROUGHLY AND COMPLETELY
THE SCOPE OF THE WORK INVOLVED, AND HAS INCLUDED ON THE BID ALL THE
NECESSARY ITEMS TO CARRY OUT THIS SECTION OF WORK.
2.
P.C. RESPONSIBLE FOR EXECUTING ALL CODE REQUIRED TESTS AND INSPECTIONS,
INCLUDING BUT NOT LIMITED TO, LEAK & PRESSURE TESTING OF GAS, WASTE, VENT
& WATER PIPING AND SANITIZING OF WATER PIPING.
3.
ENSURE PIPING LOCATED ON EXTERIOR WALLS (OR OTHER WALLS EXPOSED TO
FREEZING CONDITIONS) IS INSTALLED ON WARM-SIDE OF WALL INSULATION.
9.
ALL EXISTING EQUIPMENT AND SYSTEMS ARE ASSUMED BY ENGINEER TO BE IN
GOOD WORKING ORDER. BEFORE BEGINNING WORK P.C. IS TO ENSURE ANY
EQUIPMENT & SYSTEMS TO REMAIN ARE PROPERLY FUNCTIONING. NOTIFY G.C.
IMMEDIATELY IF PROBLEMS ARE DISCOVERED.
4.
ANY NOTCHING, DRILLING, BORING OR OTHER ALTERATION TO BUILDING
STRUCTURE SHALL BE PERFORMED IN A CODE APPROVED METHOD AND NOT
THREATEN THE INTEGRITY OF THE BUILDING STRUCTURE.
5.
SUPPORT ALL PIPING IN ACCORDANCE W/ 2012 NC PLUMBING CODE. ANY
SUSPENDED MATERIALS SHALL BE DIRECTLY SUPPORTED BY THE BUILDING
STRUCTURE.
10.
11.
ALL QUESTIONS MUST BE SUBMITTED IN RFI FORMAT TO THE ARCHITECT AND MUST
BE ADDRESSED BY THE APPROPRIATE DESIGNER OF RECORD PROIR TO BECOMING
A PROPOSED CHANGE ORDER.
P.C. IS TO REVIEW COMPLETE DRAWING SET. P.C. IS RESPONSIBLE FOR WORK
EXPLICITLY SHOWN AND WORK IMPLIED. UNLESS OTHERWISE NOTED FINAL
PLUMBING CONNECTION TO ALL EQUIPMENT, FIXTURES, ETC IS THE RESPONSIBILITY
OF THE P.C..
II. DIVISION OF WORK:
1.
2.
3.
4.
5.
6.
ALL LOW VOLTAGE WIRING RELATED TO PLUMBING EQUIPMENT AND SYSTEMS IS
THE RESPONSIBILITY OF THE PLUMBING CONTRACTOR. ALL HIGH VOLTAGE
CONNECTIONS TO PLUMBING EQUIPMENT, INCLUDING DISCONNECTS TO BE
PROVIDED AND INSTALLED BY E.C.
G.C. TO BE RESPONSIBLE FOR PROVIDING AND INSTALLING ANY ACCESS DOORS
RELATED TO PLUMBING SYSTEM (W/ EXCEPTION OF CLEANOUT COVERS, BY P.C.).
P.C. RESPONSIBLE FOR COMMUNICATING TO G.C. SIZE AND LOCATION OF REQ'D
ACCESS DOOR(S).
PLUMBING CONTRACTOR IS TO EMPLOY THE SERVICES OF THE G.C. FOR CUTTING
AND PATCHING OF WALLS, FLOORS & CEILINGS RELATED TO THE INSTALLATION OF
PLUMBING EQUIPMENT & SYSTEMS.
ALL MATERIALS SHALL BE NEW UNLESS OTHERWISE SHOWN OR SPECIFIED.
2.
ALL MATERIALS INSTALLED IN RETURN PLENUM ARE TO BE PLENUM RATED.
4.
5.
PIPING MATERIALS AND FITTINGS SHALL BE AS FOLLOWS:
WASTE & VENT (ABOVE & BELOW SLAB):
PVC PIPE, PVC SOCKET FITTINGS, AND SOLVENT-CEMENTED
FITTINGS.
DOMESTIC WATER (BELOW SLAB):
TYPE 'K' COPPER.
DOMESTIC WATER (ABOVE SLAB):
TYPE 'L' COPPER WITH SWEATED SOCKET FITTINGS. THREADED
FITTINGS MAY BE USED AT VALVES, FIXTURES & SIMILAR.
OR
CPVC PIPING WITH SOLVENT-CEMENTED FITTINGS. THREADED
FITTINGS MAY BE USED AT VALVES, FIXTURES & SIMILAR
OR
PEX PIPING WITH FLARED OR MECHANICAL JOINTS/FITTINGS.
INSULATION IS REQUIRED ON THE FIRST 8 FEET OF HOT WATER PIPING FROM WATER
HEATERS ON NON-CIRCULATING SYSTEMS. INSULATION IS REQUIRED ON ALL HOT
WATER PIPING THAT IS PART OF A HOT WATER CIRCULATION LOOP & THE FIRST 8
FEET OF BRANCH LINES FROM CIRCULATION LOOP. INSULATION TO BE EQUAL TO
"ARMAFLEX" PIPE INSULATION W/ SEALED OR TAPED SEAMS. INSULATION TO BE
MIN. 12" THICK FOR NON CIRCULATING SYSTEMS AND MIN. 1" THICK FOR
CIRCULATING SYSTEMS. INSULATION TO HAVE A CONDUCTIVITY NOT EXCEEDING
0.27 (BTU-INCH)/(HR-FT^2-°F) OR IN ACCORDANCE W/ LOCAL CODES
WHICHEVER IS MORE STRINGENT.
PROVIDE HANGERS & SUPPORTS APPROVED FOR USE BY 2012 NC PLUMBING
CODE.
MANUFACTURER
MODEL NO.
MATERIAL
STYLE
MANUFACT.
MODEL NO.
SPOUT
DRAIN
HANDLES CENTERS
TYPE
SIZE
-
FLUSH
TANK
AMERICAN
STANDARD
2835.128
VITREOUS
CHINA
ADA
ELONGATED
-
-
-
-
-
WATTS
Q894AC12
FLOOR
PROVIDE OPEN FRONT SEAT
WITH NO LID.
AMERICAN
STANDARD
0355.012
VITREOUS
CHINA
ADA
D-SHAPE
CFG
407171H
CENTER
LEVER
4"
3-HOLE
GRID
WATTS
Q894AB20
WALL
W/ WALL BRACKET. 0.5 GPM.
MOUNT AT ADA HEIGHT.
P-3
LAVATORY
DROP
IN
AMERICAN
STANDARD
0467.028
VITREOUS
CHINA
ADA
COUNTER TOP
CFG
407171H
CENTER
LEVER
4"
3-HOLE
GRID
WATTS
Q894AB20
COUNTER
P-4
WASHER
BOX
METAL
OATEY
38980
STEEL
RECESSED
-
-
-
-
-
-
WALL
W/ QTR TURN VALVES & SHOCK
ARRESTORS. W/ FACEPLATE.
W/ TAIL PIECE. REVERSIBLE BOX.
-
-
FLOOR
PEDICURE CHAIR, SELECTED BY
OWNER. INSTALLED BY P.C.
W/ VACUUM BREAKER.
-
P-5
PEDICURE
CHAIR
FLOOR
-
-
-
-
-
-
-
AAV
AIR ADM.
VALVE
THREADED
STUDOR
20301
ABS,
PVC
MINI-VENT
-
-
-
-
-
-
-
BFP-1
BACK FLOW
PREVENTER
RED. PRESS.
ZONE
WATTS
009
CAST
BRONZE
HORIZONTAL
-
-
-
-
-
-
-
FCO
FLOOR
CLEANOUT
ADJUSTABLE
ZURN
CO-2450
PVC BODY,
NICKEL CVR.
FINISHED
FLOOR
-
-
-
-
-
-
-
WH-1
WATER
HEATER
ELECTRIC
STATE
WATER HEATERS
ES6 40 DOLNS
GLASS
LINED
LOWBOY
-
-
-
-
-
-
-
VALVE SCHEDULE
TAG
DESCRIPTION
AIR ADMITTANCE VALVE
ABOVE
AUTHORITY HAVING JURISDICTION
AFF
ABOVE FINISHED FLOOR
BFP
MFG & MODEL (OR EQUAL)
BACK FLOW PREVENTER
BV
BALL OR BALANCING VALVE (SEE SCHED)
CV
CHECK VALVE
CW
COLD WATER
DN
DOWN
E.C.
ELECTRICAL SUB-CONTRACTOR
FCO
FLOOR CLEAN OUT
FD
FLOOR DRAIN
FR
FROM
FS
FLOOR SINK
GBV
G.C.
GAS BALL VALVE
GENERAL CONTRACTOR
GSV
HB
GAS SOLENOID VALVE
HOSE BIBB
HD
HUB DRAIN
FLOOR DRAIN
HW
HOT WATER
M.C.
MECHANICAL SUB-CONTRACTOR
CLEANOUT
P.C.
PLUMBING SUB-CONTRACTOR
PRV
PRESSURE REDUCING VALVE
SS
SANITARY SEWER
TV
TEMPERING VALVE
V
VENT
W
WASTE
WF
WALL FAUCET
WH
WATER HEATER
WHD
WALL HYDRANT
WASTE (SANITARY SEWER)
IND. TEMP. VALVE
WATTS USG-B
CHECK VALVE
TV-2
MASTER TEMP. VALVE
N170-M3 CSUT
(SET TO 110°F DISCHARGE)
10.
VALVES NOT DIRECTLY AT EQUIPMENT SHALL BE LABELED INDICATING THE FIXTURE
OR AREA SERVED. (NCPC 606.4)
GBV-1
GAS BALL VALVE
APOLLO 80 SERIES
11.
WATER HEATER SHALL BE FILLED WITH WATER AND PURGED AS SOON AS INSTALLED
OR IN NO EVENT LATER THAN GAS/ELECTRIC HOOK-UP.
GSV-1
GAS SOLENOID VALVE
BY OTHERS
17.
18.
19.
THE PLUMBING CONTRACTOR SHALL PROVIDE WATER HAMMER PROTECTION ON
ALL WATER DISTRIBUTION PIPING SERVING EQUIPMENT W/ QUICK CLOSING
VALVES (ICE MAKERS, DISHWASHERS, FLUSH VALVES, WASHING MACHINES, WATER
COOLERS, ETC.) SEE SHOCK ARRESTOR SCHEDULE.
ACCESS DOORS TO BE PROVIDED FOR ALL VALVES AND DEVICES REQUIRING
ACCESS WHEN LOCATED IN WALLS OR ABOVE INACCESSIBLE CEILING
CONSTRUCTION. ACCESS DOORS TO BE RATED WHERE INSTALLED IN RATED
ASSEMBLIES.
WATTS LFB6081
G
BELL & GOSSETT CB
(CIRCUIT SETTER PLUS, W/ TEST PORTS)
WATTS SD-2-MF (<1/2"), WATTS 9D (1/2"+)
(ASSE 1022 APPROVED)
GAS PIPING
EXISTING PIPING/EQUIPMENT
DEMO PIPING/EQUIPMENT
VALVE
PIPE UP
PIPE DOWN
NOTES:
1. SEE PLAN FOR SIZE. VALVE SIZE TO EQUAL LINE SIZE.
2. BALL VALVES TO INCLUDE REMOVABLE HANDLES.
3. IF AVAILABLE, VALVES MAY BE THREADED OR SWEATED CONNECTIONS. USE EXTREME
CARE AND LOW TEMP SOLDER TO PROTECT VALVE SEATS IF SWEATED CONNECTIONS
ARE USED.
4. VERIFY SOLENOID VALVE DETAILS W/ E.C. & KITCHEN EQUIPMENT/HOOD MFG.
WHERE COPPER PIPING IS SLEEVED THROUGH MASONRY, SLEEVES SHALL BE
COPPER OR RED BRASS. WHERE COPPER MUST BE CONCEALED IN A MASONRY
PARTITION OR AGAINST MASONRY, CONTACT SHALL BE PREVENTED BY COATING
THE COPPER HEAVILY WITH ASPHALTIC ENAMEL AND PROVIDING 15# ASPHALT
SATURATED FELT BETWEEN THE PIPE AND MASONRY.
VACUUM BREAKERS SHALL BE PROVIDED FOR ALL FIXTURES TO WHICH HOSES MAY
BE ATTACHED. VACUUM BREAKERS SHALL BE PERMANENTLY ATTACHED.
CONNECT TO EXISTING POINT
DEMO TO POINT
SHOCK ARRESTOR SCHEDULE
FIXTURE UNITS
UNIT SIZE (CONN. SIZE)
PROVIDE PRESSURE REDUCING VALVE IF INCOMING WATER PRESSURE EXCEEDS 80
PSI.
21.
NO INSULATION PERMITTED ON BACKFLOW PREVENTOR ASSEMBLY.
REVISIONS
MFG & MODEL (OR EQUAL)
IND. FIXTURE
SEE FIXTURE SCHEDULE
SIOUX CHIEF "MINI-RESTER"
1-11
A (1/2")
SIOUX CHIEF "HYDRA-RESTER"
12 - 32
B (3/4")
33-60
C (1")
61-113
D (1")
114-154
E (1")
REMOTE READ SUB METER BY
OWNER OR INDEPENDENT
CONTRACTOR, COORDINATE
DIMENSIONS, EXACT LOCATION
AND ELECTRICAL REQ.
VACUUM
BREAKER
C.W. TO FIXTURES
CW SUPPLY
CHECK
VALVE
APPROVED TYPE
RELIEF VALVE, NEXT
LOWER RATING AS
VALVE
CONBRACO 78-RV SERIES
BRONZE SHUT-OFF VALVE
WITH THERMAL EXPANSION
CONTROL VALVE.
NOTES:
1. LOCATED SHOCK ARRESTORS IN ACCESSIBLE LOCATION OR PROVIDE SIOUX CHIEF
BRAND ARRESTORS ONLY.
2. SEE PLAN, RISERS, SCHEDULES FOR ARRESTER LOCATIONS. IF LOCATION NOT INDICATED
INSTALL IN ACCORDNCE W/ MFG GUIDELINES.
THE PLUMBING CONTRACTOR SHALL BE RESPONSIBLE FOR PROTECTING ALL
PLUMBING EQUIPMENT FROM FOREIGN MATERIAL DURING CONSTRUCTION
(PAINT, SPACKLE, ETC.). UPON COMPLETION OF WORK THE PLUMBING
CONTRACTOR SHALL CLEAN, WASH, ETC ALL ITEMS AND EQUIPMENT WITHIN HIS
SCOPE OF WORK AND LEAVE ALL ITEMS BRIGHT AND CLEAN.
20.
38 GALLON, 6.0KW, 208V/1Ø.
30GPH @ 80°F RISE.
SET TO 110°F. SEE DETAIL.
AHJ
TV-1
PROVIDE SHUT OFF VALVES ON THE FIXTURE SUPPLY TO EACH PLUMBING FIXTURE,
APPLIANCE, OR MECHANICAL EQUIPMENT.
PO Box 1852
Cary, NC 27512
Phone: (919) 291-6736
FLOOR
PLATFORM
ABV
SUPPLY BRANCH LINES SERVING MORE THAN (1) FIXTURE SHALL INCLUDE SHUT-OFF
VALVE. LABEL VALVE AND LOCATE AS CLOSE TO RISER/MAIN AS POSSIBLE. (NCPC
606.2.1)
16.
MARLIN DESIGN BUILD
FOLLOW MFG'S INSTRUCTIONS.
PROVIDE REQ'D CLEARANCE.
DISCHARGE TO DRAIN W/ AIR GAP.
AAV
VALVE
15.
SEE
PLAN
VENT PIPING
PRESS. RED. VALVE
ALL PIPE INSULATION SHALL RUN CONTINUOUSLY THROUGH FLOORS, WALLS, AND
PARTITIONS. PIPE INSULATION SHALL BE MITERED AT ELBOWS AND TEES TO ENSURE
COMPLETE COVERAGE OF PIPING.
W/ ACCESS COVER (IF REQ'D).
PIPE
WALL
DOMESTIC HOT WATER PIPING
PRV-1
14.
SEE
PLN
DOMESTIC COLD WATER PIPING
WATTS 223-S
(SET TO 40 PSI)
13.
0.5 GPM.
BARRIER FREE.
PLUMBING LEGEND
NOTE:
CONFIRM FIXTURE
SELECTIONS WITH OWNER
PRIOR TO BID.
WATTS CV
COPPER PIPING SHALL BE PROTECTED AGAINST CONTACT WITH MASONRY OR
DISSIMILAR METALS. ALL HANGERS, SUPPORTS, ANCHORS, AND CLIPS SHALL BE
COPPER OR COPPER PLATED. WHERE COPPER PIPING IS CARRIED ON IRON
TRAPEZE HANGERS WITH OTHER PIPING, SATISFACTORY AND PERMANENT
ELECTROLYTIC ISOLATION MATERIAL SHALL PROTECT THE COPPER AGAINST
CONTACT WITH OTHER METALS.
plumbing mechanical electrical
NOTES:
1. ALL FIXTURE COLORS & FINISHES TO BE APPROVED BY OWNER & ARCHITECT BEFORE PURCHASING.
2. PROVIDE P-TRAP AND SUPPLY LINE SAFETY COVERS FOR ALL ADA SINK AND LAVATORY INSTALLATIONS.
3. WATER CLOSET HANDLES TO BE LOCATED ON "WIDE SIDE" OF STALL FOR ADA FIXTURES.
4. SEE DETAIL SHEET FOR ADDITIONAL ITEMS TO BE PROVIDED/INSTALLED W/ FIXTURES LISTED ABOVE.
BRONZE CHECK VALVE
12.
1405 HILLSBOROUGH ST
RALEIGH, NC 27605
LIC.#: P-0990
P:919-341-4247
F:919-890-3797
3/18/14
-
CV-2
9.
REMARKS
WALL
MOUNT
DBL CHECK VALVE
CLEANOUT PLUGS SHALL BE INSTALLED IN ACCORDANCE WITH PLUMBING CODE
REQUIREMENTS. PROVIDE CLEANOUTS AS PLANS INDICATED AND AT THE BASE OF
ALL WASTE STACKS, AT EVERY FOUR 45 DEGREE TURNS, AT EVERY 100 FEET, AND AT
THE BASE OF ALL ROOF LEADERS. CLEANOUTS SHALL BE PLACED IN READILY
ACCESSIBLE LOCATIONS.
MOUNTING
WATER
CLOSET
CV-1
8.
HW
LAVATORY
BALANCING VALVE
PENETRATIONS OF ALL EXTERIOR WALLS, FLOORS AND CEILINGS SHALL BE SEALED
IN AN AIR TIGHT MANNER AND IN ACCORDANCE W/ 2012 NCECC APPENDIX 2
DETAILS.
WASTE VENT CW
P-2
BV-2
7.
ENGINEERING, pllc
PIPE SIZES
SUPPLIES
AND STOPS
P-1
FULL-PORT BALL VALVE
G.C. TO BE RESPONSIBLE FOR PROVIDING AND INSTALLING ANY WATER HEATER
PLATFORMS, EITHER FLOOR/WALL MOUNTED OR SUSPENDED. P.C. TO
COMMUNICATE REQ'S TO G.C.
ALL GAS PIPING IS BY MECHANICAL CONTRACTOR.
1.
PROVIDE A U.L. LISTED ASSEMBLY FOR ALL PENETRATIONS THRU FIRE RATED WALLS,
FLOORS & CEILINGS.
FAUCET/VALVE
TYPE
BV-1
ALL ROOF PENETRATIONS, FLASHING, ETC ARE TO BE PERFORMED BY ROOFING
CONTRACTOR.
III. MATERIALS:
3.
6.
maple
PLUMBING FIXTURE SPECIFICATIONS AND CONNECTION SCHEDULE
FIXTURE
MARK
EXPANSION TANK
TEMPERATURE AND
PRESSURE RELIEF VALVE
BALL
VALVE
FINISH FLOOR LEVEL
TOP SUITABLE FOR
FINISHED FLOOR,
TILE, CARPET, CONC., ETC.
DISCHARGE FULL SIZE
OF VALVE DISCHARGE.
SPILL INTO DRAIN PAN
WATER
HEATER
UNION
DATE
H.W. TO FIXTURES
1-1/2" DEEP GALV.
DRAIN PAN
HB
PLATFORM
WATER HEATER ON PLATFORM BY
G.C. SIZE PER LOCAL SIESMIC
REQUIREMTNS AND TOTAL WEIGHT
OF WATER HEATER FULL OF
WATER.
1" DRAIN LINE
TO EXTERIOR.
SOIL PIPE
NOTE:
1.
INSTALL WATER HEATER PER MANUFACTURER REQUIREMENTS
2.
PROVIDE HEAT TRAP ON CW AND HW LINES PER ENERGY CODE
3.
ELEVATE DRAIN PAN AS NECESSARY TO ALLOW PROPER FLOW TO HUB DRAIN
2
FLOOR CLEANOUT DETAIL
NO SCALE
1
WATER HEATER DETAIL (PLATFORM)
NO SCALE
MAR. 18, 2014
DRAWN BY
RDG
PROJECT NO.
MDB-1402
SHEET TITLE
PLUMBING
SCHEDULES
DETAILS
& NOTES
SHEET
P0.1
1 OF 2
FIRE RATING LEGEND
1-HR WALL
2-HR WALL
maple
ENGINEERING, pllc
RALEIGH, NC 27605
LIC.#: P-0990
P:919-341-4247
F:919-890-3797
1-1/2" AAV
WH-1
ABV CLG
1 1/2"
3/18/14
FINISH FLOOR
2" TO S.S.
2
P-2
FLEXIBLE CONNECTION
2" P-TRAP
4
P-4
CHAIR DETAIL
Restrm
Passage
P-2
P-1
NO SCALE
P-2
Office
Waxing
1
NOTE:
P.C. TO VERIFY EXISTING
LINES. P.C. TO TAKE ALL
MEASURES POSSIBLE TO
ENSURE GREASY WASTE
AND SANITARY SEWER
SYSTEMS DO NOT BECOME
INTERCONNECTED. P.C.
RESPONSIBLE FOR ANY
INTERCONNECTION THAT
OCCURS.
MARLIN DESIGN BUILD
PO Box 1852
Cary, NC 27512
Phone: (919) 291-6736
EXIST. S.S.
1
Waxing
4
BV-1
4
EXIST CW OVERHEAD
FR METER & BLDG RPZ
HW/CW
IN FURROUT
P-5
HW/CW
IN FURROUT
P-5
TAGGED NOTES - THIS SHEET
3
1
CLEARLY LABEL ALL PORTIONS OF CW LINE UPSTREAM
OF BFP "DO NOT TAP".
2
BACK FLOW PREVENTER BFP-1 LOCATED ON BACK
WALL. DRAIN TO EXTERIOR. ENSURE REQ'D
CLEARANCES CAN BE MAINTAINED. CONFIRM
LOCATION WITH OWNER & G.C.
3
HW/CW CONNECTIONS TO CHAIR W/ CV-1'S &
DOUBLE CHECK VALVES. CONFIRM EXACT CHAIR
LOCATION & CONNECTIONS WITH OWNER. TYPICAL.
4
HW/CW DN W/ VALVES & ACCESS PANEL.
Pedicure Area
P-5
P-5
COLUMN
P-5
FCO
WATER RISER
3
NO SCALE
GENERAL NOTES - THIS SHEET
1.
2.
3.
4.
FCO
3
HW/CW
IN FURROUT
P-5
ITEMS SHOWN IN FAINT & HATCHED ARE TO BE DEMO'D OR
RELOCATED. ITEMS SHOWN IN FAINT ARE EXISTING TO
REMAIN. NEW OR RELOCATED ITEMS ARE SHOWN IN BOLD.
SEE LEGEND.
P.C. TO VERIFY EXACT SIZE, LOCATION, INVERT & DIRECTION
OF EXISTING LINES BEFORE BEGINNING WORK.
P.C. TO VERIFY THAT NO FIXTURES ARE CONNECTED
UPSTREAM OF BACK FLOW PREVENTER.
P.C. TO CONFIRM EXACT LOCATION, SIZE & METHOD OF
PLUM. CONNECTIONS TO PEDICURE CHAIRS W/ OWNER
BEFORE BEGINNING WORK.
P-3
Manicure Area
4
REVISIONS
Reception
DATE
MAR. 18, 2014
DRAWN BY
RDG
PROJECT NO.
MDB-1402
SHEET TITLE
PLUMBING
PLAN
& RISERS
2
WASTE/VENT RISER
NO SCALE
1
PLUMBING PLAN
SCALE: 1/4" = 1'-0"
SHEET
P1.1
2 OF 2
PACKAGED DX COOLING/GAS-ELEC HEATING ROOF TOP UNIT SCHEDULE
HVAC GENERAL NOTES
EVAPORATOR FAN DATA
1.
MECHANICAL CONTRACTOR IS TO FURNISH AND PAY FOR ALL LABOR, MATERIAL,
EQUIPMENT, PERMITS & FEES REQUIRED FOR THE COMPLETE INSTALLATION OF ALL
SYSTEMS IN THIS SECTION OF WORK.
2.
ALL WORK IS TO BE PERFORMED IN ACCORDANCE WITH NC MECHANICAL CODES
AND ALL OTHER APPLICABLE CODES. MC IS TO COORDINATE W/ G.C. IN REGARDS
TO PROJECT TIMELINE, WORK HOURS, AS WELL AS ANY BONDING OR INSURANCE
REQUIREMENTS.
3.
ALL MECHANICAL EQUIPMENT SHALL BE PROVIDED COMPLETE WITH ALL
ACCESSORIES, HANGERS, SUPPORTS, CONTROLS, ETC FOR A FULLY FUNCTIONING
SYSTEM REGARDLESS OF PRESENCE ON PLANS.
4.
ALL EQUIPMENT, MATERIALS AND INSTALLATION SHALL BE GUARANTEED TO BE FREE
OF DEFECTS FOR A PERIOD OF ONE (1) YEAR AFTER FINAL ACCEPTANCE OF WORK
OR IN ACCORDANCE WITH THE MANUFACTURER'S STANDARD GUARANTEE, IF
LONGER. ALL COMPRESSORS ARE TO INCLUDE FIVE (5) YEAR WARRANTY. EXISTING
EQUIPMENT IS EXCLUDED FROM WARRANTY REQUIREMENT.
5.
THESE DRAWINGS ARE DIAGRAMMATIC AND SHOW GENERAL LOCATION AND
ARRANGEMENT OF ALL MATERIALS AND EQUIPMENT. THE DRAWINGS SHALL BE
FOLLOWED AS CLOSELY AS BUILDING CONSTRUCTION AND ALL OTHER WORK WILL
PERMIT.
6.
ALL DUCT DIMENSIONS SHOWN ARE INTERIOR DUCT DIMENSIONS.
7.
INFORMATION GIVEN IN SCHEDULES INCLUDES BOTH DESCRIPTION OF PRODUCT
AND MANUFACTURER'S MODEL #. IF CONFLICT IS PRESENT BETWEEN DESCRIPTION
AND MODEL #, EQUIPMENT DESCRIPTION SHALL TAKE PRECEDENT. IN CASE OF
CONFLICT BETWEEN THE PLANS AND NOTES/SPECIFICATIONS OR CONFLICT BETWEEN
INFORMATION PRESENTED ON THE PLANS OR IN THE NOTES/SPECIFICATIONS, THEN
THE MOST RESTRICTIVE SHALL TAKE PRECEDENT.
8.
9.
BEFORE BID MC IS RESPONSIBLE FOR CLARIFYING W/ G.C. ANY CONFUSION IN
REGARDS TO RESPONSIBILITY OF WORK TO BE PERFORMED OR MATERIALS TO BE
PROVIDED. THE SUBMITTAL OF THE BID BY THE CONTRACTOR WILL BE HELD AS
PROOF THAT THE CONTRACTOR UNDERSTANDS THOROUGHLY AND COMPLETELY
THE SCOPE OF THE WORK INVOLVED, AND HAS INCLUDED ON THE BID ALL THE
NECESSARY ITEMS TO CARRY OUT THIS SECTION OF WORK.
AS SOON AS POSSIBLE (AND NOT MORE THAN 30 DAYS) AFTER CONTRACT IS
SIGNED, THE MC SHALL PROVIDE SUBMITTALS OF MECHANICAL EQUIPMENT HE/SHE
INTENDS TO PURCHASE FOR REVIEW AND COMMENT BY THE ENGINEER. ENGINEER IS
TO APPROVE SUBMITTALS BEFORE EQUIPMENT IS ORDERED.
6.
7.
ALL MAIN DUCTWORK (INCLUDING EXHAUST) TO BE SEALED ACCORDING TO 2012
NCECC AND AT A MINIMUM INCLUDE SEALING OF ALL DUCT SEAMS W/
NON-HARDENING MASTIC. SEALING BY TAPE ALONE NOT ALLOWED.
8.
CONDENSATE DRAIN PIPING AND FITTINGS SHALL BE SCHEDULE 40 PVC.
9.
ALL DAMPERS TO INCLUDE SET SCREW OR SIMILAR FEATURE FOR LOCKING IN
POSITION.
10. ALL REFRIGERANT LINE MATERIAL AS PER MFG'S REQUIREMENTS. SIZE PER MFG
INSTRUCTIONS. SUCTION LINE TO BE INSULATED W/ MIN. 1-1/2" ARMAFLEX W/ TAPED
OR SEALED SEAMS.
11. ALL FIRE, SMOKE AND RADIATION DAMPERS TO BE U.L. LISTED AND APPROVED FOR
CORRECT PRESSURE CLASS, APPLICATION (STATIC, DYNAMIC), ORIENTATION
(HORIZONTAL/VERTICAL), AND INSTALLATION (WALL, FLOOR CEILING U.L.
ASSEMBLY). TO INCLUDE 165° FUSIBLE LINK UNLESS OTHERWISE NOTED.
12. M.C. IS TO PROVIDE TRAINING TO OWNER OR OWNER'S REPRESENTATIVE IN
REGARDS TO OPERATION, FUNCTION, AND MAINTENANCE OF ALL MECHANICAL
EQUIPMENT, CONTROLS, ETC.
13. M.C. IS TO REVIEW COMPLETE DRAWING SET. M.C. IS RESPONSIBLE FOR WORK
EXPLICITLY SHOWN AND WORK IMPLIED.
ALL ROOF WORK INCLUDING PENETRATIONS, OPENINGS, FLASHING, CURB INSTALLS,
ETC ARE TO BE PERFORMED BY ROOFING CONTRACTOR. M.C. RESPONSIBLE FOR
PROVIDING ANY ROOF CURBS, EQUIPMENT RAILS, VENTS, ETC AND
COMMUNICATING ALL REQ'S WITH G.C. & ROOFING CONTRACTOR.
ALL GAS PIPING IS BY MECHANICAL CONTRACTOR.
1.
ALL MATERIALS SHALL BE NEW UNLESS OTHERWISE SHOWN OR SPECIFIED.
2.
PROVIDE HANGERS & SUPPORTS APPROVED FOR USE BY 2012 NC MECHANICAL
CODE.
3.
ALL MAIN DUCTWORK (SUPPLY, RETURN, EXHAUST, OUTSIDE AIR) SHALL BE
GALVANIZED SHEET METAL CONSTRUCTED IN ACCORDANCE WITH SMACNA
STANDARDS. RUNOUTS FROM MAIN/BRANCH DUCTS MAY BE FLEXIBLE DUCT
CONFORMING TO THE REQUIREMENTS OF UL 181 FOR CLASS 1 FLEXIBLE AIR DUCTS.
MAX. LENGTH OF FLEX PER RUNOUT TO BE 6'-0" UNLESS SHOWN OTHERWISE.
4.
NO FLEXIBLE DUCT ALLOWED FOR NEGATIVE PRESSURE EXHAUST APPLICATIONS.
5.
ALL SUPPLY AND RETURN DUCTWORK AND PLENUMS SHALL BE INSULATED.
INSULATION OF DUCTWORK IN UNCONDITIONED SPACE SHALL BE MINIMUM R-5 PER
2012 NCECC. INSULATION OF DUCTWORK OUTSIDE BUILDING THERMAL ENVELOPE
(I.E. ROOF, ATTIC, CRAWLSPACE) SPACE SHALL BE MINIMUM R-8 PER 2012 NCECC.
COMPRESSOR CYCLE DELAY AND WINTER START TIME DELAY (IF AVAILABLE).
4.
PROVIDE 3 SETS OF NEW FILTERS FOR EACH UNIT. PROVIDE ONE AT INSTALLATION, ONE
PRIOR TO AIR BALANCE AND ONE AT TURNOVER TO OWNER.
5.
PROVIDE FACTORY ROOF CURB AND AIR SIDE DIFFERENTIAL ENTHALPY ECONOMIZER SECTION WITH BAROMETRIC
RELIEF DAMPER FOR EACH UNIT.
MANICURE
400
0.4"
MFG
DOWNBLAST
CENTRIFUGAL
MFG
DOWNBLAST
CENTRIFUGAL
EF-3
THE MECHANICAL CONTRACTOR SHALL COORDINATE CLOSELY WITH ALL OTHER
TRADES TO AVOID CONFLICT AND ENSURE OTHER TRADES PROVIDE MEASURES TO
ACCOMMODATE MECHANICAL WORK (I.E. ACCESS DOORS, SLAB/WALL/ROOF
OPENINGS, ELECTRICAL CONNECTIONS, ETC).
SEAL ALL PENETRATIONS OF RATED WALLS, CEILING, FLOORS IN ACCORDANCE W/
APPROPRIATE U.L. PENETRATION DETAIL.
4.
INSTALL ALL CONTROL DEVICES, INCLUDING THERMOSTATS AND SWITCHES, 4'-0"
ABOVE FINISHED FLOOR.
8.
SUPPORT ALL DUCTWORK AND PIPING IN ACCORDANCE W/ 2012 NC MECHANICAL
CODE. ANY SUSPENDED MATERIALS SHALL BE DIRECTLY SUPPORTED BY THE BUILDING
STRUCTURE.
9.
PENETRATIONS OF ALL EXTERIOR WALLS, FLOORS AND CEILINGS SHALL BE SEALED IN
AN AIR TIGHT MANNER AND IN ACCORDANCE W/ 2012 NCECC APPENDIX 2
DETAILS. ALL PENETRATIONS OF WALLS, FLOORS & CEILINGS IN RETURN OR EXHAUST
PLENUMS SHALL BE SEALED IN AN AIR TIGHT MANNER.
10. DUCT ACCESS DOORS TO BE PROVIDED AT ALL FIRE, RADIATION & SMOKE
DAMPERS, SMOKE DETECTORS, CLEANOUTS AND ANY OTHER CODE REQUIRED
LOCATIONS.
11. THE MECHANICAL CONTRACTOR SHALL BE RESPONSIBLE FOR PROTECTING ALL
MECHANICAL EQUIPMENT FROM FOREIGN MATERIAL DURING CONSTRUCTION
(PAINT, SPACKLE, ETC.). UPON COMPLETION OF WORK THE MECHANICAL
CONTRACTOR SHALL CLEAN, WASH, ETC ALL ITEMS AND EQUIPMENT WITHIN HIS
EXHAUST
PEDICURE
600
0.65"
MANUF.
MODEL
45
TRANE
YHC060
NOM. EER
TON. (SEER)
5.0
12.9
PROVIDE WITH THROUGH THE BASE ELECTRICAL CONNECTION.
7.
PROVIDE WITH FACTORY MOUNTED DISCONNECT AND FACTORY POWERED GFI RECEPTICAL.
WT.
(LBS)
841
NOTES
1,2,3,4,5,6,7
maple
ENGINEERING, pllc
RALEIGH, NC 27605
LIC.#: P-0990
P:919-341-4247
F:919-890-3797
MARLIN DESIGN BUILD
113 WATTS
120V/1Ø
1/6 HP
120V/1Ø
1/6 HP
120V/1Ø
MECHANICAL LEGEND
MANUFACTURER
& MODEL NO.
GREENHECK
SPA-190
GREENHECK
G-085
GREENHECK
G-095
DRIVE
CONTROL SCHEME
DIRECT
A
NOTES
1,2,3,4
DIRECT
B
1,2,3,4,5,6
DIRECT
B
1,2,3,4,5,6
18x14
RECTANGULAR DUCT
6Ø
ROUND METAL DUCT
6Ø
FLEX/RIGID ROUND DUCT
W/ SCREEN
BACKDRAFT DAMPER
5.
SPEED CONTROLLER
3.
COLOR BY ARCHITECT
6.
W/ INSULATED MFG. ROOF CURB
4.
INTEGRAL DISCONNECT SWITCH
PO Box 1852
Cary, NC 27512
Phone: (919) 291-6736
ELBOW WITH TURNING VANES
CONTROL OPTIONS:
1.
2.
VOLUME DAMPER
A. CONTROL W/ ROOM LIGHTS
B. CONTROL W/ SPEED CONTROLLER
SUPPLY TAP WITH VOLUME DAMPER
SUPPLY TAP
SUPPLY DIFFUSER/GRILLE OR RISER
CFM
NECK
SIZE
MODULE
SIZE
FRAME
TYPE
PATTERN
A
AS NOTED
AS NOTED
24x24
LAY-IN
PLAQUE
NO
B
AS NOTED
AS NOTED
12x24
LAY-IN
PERF.
NO
RETURN REGISTER/GRILLE OR RISER
SERVICE
FINISH
MANUFACTURER
& MODEL NO.
STEEL
SUPPLY
NOTE 2
TITUS OMNI
1,2,3
STEEL
SUPPLY
NOTE 2
TITUS PAS
1,2,3
DAMPER MATERIAL
EXHAUST REGISTER/GRILLE OR RISER
NOTES
SIDEWALL DIFFUSER/GRILLE
CEILING EXHAUST FAN
M.C. TO FOLLOW MANUFACTURER'S INSTRUCTIONS WHEN INSTALLING MECHANICAL
EQUIPMENT. ENSURE REQUIRED MAINTENANCE ACCESS AND CLEARANCES ARE
MAINTAINED. IF CONFLICT EXISTS BETWEEN THESE PLANS AND MFG INSTRUCTIONS
CONTACT ENGINEER.
3.
MOCP
(A)
30.0
3/18/14
TYPE &
MIN. MOTOR HP
ARRANGEMENT
& VOLTAGE
SYMBOL
LOCATE CEILING DIFFUSERS IN ACCORDANCE WITH ARCHITECTURAL REFLECTED
CEILING PLANS (IF PROVIDED).
ALL PENETRATIONS THROUGH EXTERIOR WALLS & ROOF SHALL BE FLASHED &
COUNTER-FLASHED IN A WATERPROOF MANNER.
MCA
(A)
208V/3Ø
1
DIFFUSER SCHEDULE
V. EXECUTION:
2.
GENERAL DATA
VOLTAGE
(V/PH)
N/A
48.0
6.
NOTES:
IV. COORDINATION:
1.
ELECTRICAL DATA
OUTPUT ELEC HEAT
# OF
(MBH)
(KW)
STAGES
FAN SCHEDULE
EXHAUST
4.
60.0
3.
EF-2
M.C. TO COORDINATE LOCATION OF ALL ROOF PENETRATIONS W/ ROOFING
CONTRACTOR. P.C. & M.C. TO COORDINATE TO ENSURE NO PLUMBING VENTS OR
ANY OTHER SOURCES OF BUILDING EXHAUST ARE LOCATED WITHIN 10' OF ANY
OUTSIDE AIR INTAKES.
INPUT
(MBH)
N/A
PROVIDE MANUFACTURER'S 7 DAY PROGRAMMABLE THERMOSTAT W/ MANUAL OVERRIDE & REMOTE
AVERAGING SENSOR. (T-STAT & SENSOR TO MEASURE TEMPERATURE IN (2) LOCATIONS)
14. GAS PIPING TO BE SCHEDULE 40 BLACK STEEL PIPE W/ THREADED FITTINGS.
APPROVED FLEXIBLE GAS PIPING MAY BE USED AT CONNECTION TO EQUIPMENT.
3.
REHEAT
(MBH)
1
COOLING CAPACITIES ARE RATED IN ACCORDANCE WITH AT LEAST ONE OF THE FOLLOWING ARI
STANDARDS;; 210-94, 270-95, OR 360-93 AT 95°F AMBIENT OUTDOOR AIR TEMP., 80°F DRY BULB, 67° WET BULB
ENTRANCE AIR TEMP., AND AIR QUANTITY LISTED BY MFG.
CEILING,
CENTRIFUGAL
MECHANICAL CONTRACTOR SHALL VERIFY LOCATION OF ALL PENETRATIONS FOR
RELIEF HOODS, OUTSIDE AIR HOODS, LOUVERS, AND WALL CAPS WITH ARCHITECT &
OWNER PRIOR TO INSTALLATION.
# OF
STAGES
48.1
2.
RPM
2.
SENS.
(MBH)
62.3
1.
MFG.
1.
HEATING SECTION
TOTAL
(MBH)
80/67
NOTES:
S.P.
PENETRATIONS OF NON-RATED WALLS, PARTITIONS AND FLOOR OF COMBUSTIBLE
CONSTRUCTION SHALL BE FIRESTOPPED WITH MATERIALS EQUIVALENT TO TWO
INCHES OF WOOD. FIRESTOPPING SHALL COMPLY WITH ASTM E-814.
8.
93/76
0.35"
7.
III. MATERIALS:
AMBIENT
ENT. AIR
DB/WB (°F) DB/WB (°F)
75
ALL REFRIGERANT PIPING SHALL BE INSTALLED PER MFG'S INSTRUCTIONS IN REGARDS
TO SUPPORTS, BENDS, FITTINGS, OIL TRAPS, ETC.
G.C. TO BE RESPONSIBLE FOR PROVIDING AND INSTALLING ANY WALL LOUVERS
BRICK VENTS OR SIMILAR. M.C. TO PROVIDE AND INSTALL ANY WALL CAPS.
FAN
RPM
MFG.
CFM
6.
7.
COOLING SECTION
1.0
AREA
SERVED
G.C. TO BE RESPONSIBLE FOR PROVIDING AND INSTALLING ANY ACCESS DOORS
(WALL, FLOOR, CEILING) RELATED TO MECHANICAL SYSTEM. M.C. RESPONSIBLE FOR
COMMUNICATING TO G.C. SIZE AND LOCATION OF REQ'D ACCESS DOOR(S).
G.C. TO BE RESPONSIBLE FOR PROVIDING AND INSTALLING ANY ACCESS
PLATFORMS, GUARD RAILS, LADDERS, CONCRETE PADS. M.C. TO COMMUNICATE
REQ'S TO G.C.
0.75
BATHROOM
3.
6.
500
SERVICE
INDEPENDENT CERTIFIED TEST AND BALANCE CONTRACTOR SHALL BALANCE SYSTEM
TO AIR QUANTITIES INDICATED ON PLANS AND IN ACCORDANCE W/ 2012 NCECC
SEC. 503.2.9. M.C. TO PROVIDE OWNER'S REPRESENTATIVE & ENGINEER WITH
COMPLETE BALANCE REPORT. MC RESPONSIBLE FOR PROVIDING ANY DAMPERS,
VALVES, PORTS, ETC. NECESSARY FOR A COMPLETE SYSTEM BALANCE.
G.C. RESPONSIBLE FOR PAINTING OF ANY EXPOSED DUCT, PIPING, GRILLES, ETC.
M.C. RESPONSIBLE FOR CLEANING AND PREPARING ITEMS FOR PAINT, COORDINATE
W/ G.C.
1990
EXHAUST
5.
5.
-
EF-1
ALL LOW VOLTAGE WIRING RELATED TO MECHANICAL EQUIPMENT AND SYSTEMS IS
THE RESPONSIBILITY OF THE MECHANICAL CONTRACTOR (ANY LOW VOLTAGE FIRE
ALARM WIRING TO BE BY E.C.). ALL HIGH VOLTAGE CONNECTIONS TO
MECHANICAL EQUIPMENT, TO BE PROVIDED AND INSTALLED BY E.C. (SEE
EQUIPMENT SCHEDULE FOR DISCONNECT RESPONSIBILITY).
MECHANICAL CONTRACTOR IS TO EMPLOY THE SERVICES OF THE G.C. FOR CUTTING
AND PATCHING OF WALLS, FLOORS & CEILINGS RELATED TO THE INSTALLATION OF
MECHANICAL EQUIPMENT & SYSTEMS.
SALON
OA, MAX OA, MIN
ESP
MOTOR
(CFM)
(CFM) (" OF WG) (HP)
UNIT
NO.
2.
4.
RTU-1
FAN
CFM
13. ALL PROGRAMMABLE THERMOSTATS TO INCLUDE BATTERY BACK-UP AND HAVE
CAPABILITY TO SETBACK TO 55°F (HEATING) & 85°F (COOLING).
AUTO-CHANGEOVER THERMOSTATS TO HAVE A MIN. 5°F DEADBAND.
1.
AREA
SERVED
12. ALL FIRE SEALANTS TO BE U.L. LISTED AND APPROVED FOR USE W/ APPROPRIATE U.L.
PENETRATION DETAIL.
10. ALL QUESTIONS MUST BE SUBMITTED IN RFI FORMAT TO THE ARCHITECT AND MUST BE
ADDRESSED BY THE APPROPRIATE DESIGNER OF RECORD PROIR TO BECOMING A
PROPOSED CHANGE ORDER.
11. UPON COMPLETION OF WORK M.C. IS TO PROVIDE OWNER W/ COMPLETE BOUND
SET OF ALL EQUIPMENT OPERATION & MAINTENANCE MANUALS. PACKAGE IS ALSO
TO INCLUDE AND WARRANTY & GUARANTEE INFORMATION.
UNIT
TAG
CONCEALED SHEET METAL SUPPLY & RETURN DUCT MAY BE EXTERNALLY INSULATED
WITH MINERAL FIBER BOARD OR BLANKET OR MAY BE INTERNALLY INSULATED WITH
ACOUSTICAL DUCT LINER. EXPOSED SPIRAL DUCTWORK DOES NOT REQUIRE
INSULATION UNLESS OTHERWISE NOTED (WHEN INSTALLED IN CONDITIONED SPACE).
C
AS NOTED
N/A
AS NOTED
SURFACE
SNG. DEFL.
NO
STEEL
SUPPLY
NOTE 2
TITUS 301FS
1,2,3,4
D
AS NOTED
N/A
AS NOTED
SURFACE
LOUVERED
NO
STEEL
EXHAUST
NOTE 2
TITUS 350RL
1,2
STEEL
FILTER
RETURN
NOTE 2
TITUS 8RF
E
AS NOTED
N/A
24x24
LAY-IN
PERF.
NO
T-STAT
S
REMOTE AVERAGING TEMP SENSOR
3/4" DOOR UNDER CUT
1,2,3
GENERAL - MC RESPONSIBLE FOR VERIFYING QTY, COLOR & FRAME TYPE
OF DIFFUSERS/GRILLES BEFORE ORDERING. PROVIDE SQR TO RND
TRANSTIONS & PLENUMS AS NECESSARY.
2.
FINISH TO MATCH / BE ABLE MATCH CEILING OR WALL OR DOOR.
3.
FACTORY INSULATION BACKING ON GRILLES EXPOSED TO NON-CONDITIONED AREAS.
ALTERNATELY, FIELD SUPPLY AND INSTALL.
1.
4.
SET BLADE ANGLE TO 0°.
DIFFUSER DESIGNATIONS ON PLANS AS FOLLOWS:
DIFFUSER OR
DIFFUSER TYPE
NECK SIZE.
8x4
AS NOTED ABOVE
A
75
AIR QUANTITY
T
ENERGY REQUIREMENTS:
MECHANICAL SYSTEMS, SERVICE SYSTEMS AND EQUIPMENT
METHOD OF COMPLIANCE
PRESCRIPTIVE
ENERGY COST BUDGET
THERMAL ZONE
4A
EXTERIOR DESIGN CONDITIONS
WINTER DRY BULB
SUMMER DRY BULB
14
93
INTERIOR DESIGN CONDITIONS
WINTER DRY BULB
SUMMER DRY BULB
RELATIVE HUMIDITY
70
75
50%
BUILDING HEATING LOAD (MBH)
53.8 MBH
BUILDING COOLING LOAD (MBH)
43.2 MBH
MECHANICAL SPACING CONDITIONING SYSTEM
UNITARY
DESCRIPTION OF UNIT
HEATING EFFICIENCY
COOLING EFFICIENCY
HEAT OUTPUT OF UNIT
COOLING OUTPUT OF UNIT
BOILER
TOTAL BOILER OUTPUT
CHILLER
TOTAL CHILLER OUTPUT
LIST EQUIPMENT EFFICIENCIES
SEE SCHEDULES
SEE SCHEDULES
SEE SCHEDULES
SEE SCHEDULES
SEE SCHEDULES
NA
NA
SEE SCHEDULES
DESIGNER'S STATEMENT:
TO THE BEST OF MY KNOWLEDGE AND BELIEF, THE DESIGN OF THIS BUILDING
COMPLIES WITH THE MECHANICAL SYSTEMS, SERVICE SYSTEMS AND EQUIPMENT
REQUIREMENTS OF THE N.C.S. ENERGY CODE.
DATE
MAR. 18, 2014
DRAWN BY
BTM
PROJECT NO.
MDB-1402
SIGNED:
NAME: ZACK L. TOMLIN, PE
TITLE:
REVISIONS
MECHANICAL ENGINEER
SHEET TITLE
MECHANICAL
SCHEDULES
& NOTES
SHEET
M0.1
1 OF 3
FIRE RATING LEGEND
1-HR WALL
2-HR WALL
maple
ENGINEERING, pllc
RALEIGH, NC 27605
LIC.#: P-0990
P:919-341-4247
F:919-890-3797
3/18/14
Passage
7Ø
B 115
Restrm
B 5Ø
25
MARLIN DESIGN BUILD
1
3
EF-1
B 6Ø
75
PO Box 1852
Cary, NC 27512
Phone: (919) 291-6736
Office
DRYER VENT LENGTH
7Ø
2012 NCMC SEC 504.6
BREAK ROOM:
LENGTH = 15' (V) + 0' (H) = 15' < 35'
1.
6Ø
Waxing
INSTALLED DRYER MUST BE RATED BY MFG FOR VENT LENGTH OF
15' OR GREATER.
5Ø
6Ø
B 100
6Ø
B 6Ø
75
Waxing
6Ø
FLARED SHOULDER &
SPIN IN COLLAR W/
INTEGRAL SCOOP.
REDUCER OR
SQUARE TO ROUND
TRANSITION
(IF NECESSARY)
CIRCULAR CLAMP
TYP.
FINISHED
CEILING SURFACE
DIFFUSER/GRILLE
(COORD. FRAME TYPE)
5
4
SUPPLY GRILLE IN BULKHEAD. CENTER VERTICALLY IN
BULKHEAD.
5
PROVIDE 6Ø EXHAUST TAP W/ DAMPER OVER TO 9x3
EXHAUST DUCT IN STUD CAVITY. DUCT NOT TO BE IN
RATED WALL. PROVIDE 6x6 TYPE "D" GRILLE, BOTTOM
OF GRILLE TO BE 12" AFF. BALANCE TO 75 CFM
EXHAUST. COORDINATE INSTALLATION W/ G.C.
BEFORE BEGINNING WORK.
6x6 EXHAUST DUCT DOWN TO NAIL STATION TABLE.
G.C. TO PROVIDE CHASE.
6
NOTES:
1. PROVIDE INSULATED REGISTER BOOT/PLENUM BOX IF NECESSARY.
2. RETURN APPLICATION IS SIMILAR. ALL ELBOWS IN RETURN APPLICATION
TO BE INSULATED SHEET METAL (NO FLEX ELBOWS).
DIFFUSER DETAIL
NO SCALE
PROVIDE 4Ø DRYER VENT UP TO ROOF JACK W/ BDD.
INSTALL ABOVE EMERGENCY DRAIN LEVELS. MAINTAIN 10'
CLEARANCE FROM ALL BUILDING AIR INTAKES.
7
MAIN SUPPORT GIRDER. PROVIDE AND INSTALL
ROOFTOP UNIT AND CURB IN THIS LOCATION FOR
MAXIMUM SUPPORT. ROUTE SUPPLY/RETURN DUCT
DOWN INBETWEEN BAR JOISTS.
8
12X10 DOWN FROM EF ON ROOF.
9
8X8 DOWN FROM EF ON ROOF.
10
DUCT TO RUN BETWEEN NAIL STATION TABLE FRAMING.
COORDINATE W/ G.C.. PROVIDE EXHAUST GRILLE AS
SHOWN. INSTALL GRILLE AS HIGH AS POSSIBLE.
8Ø
A 175
8
Pedicure Area
5
5
8Ø
10Ø
EF-3
8Ø
10Ø
10Ø
8Ø
7
10Ø
8Ø
5
14Ø
2
RTU-1
5
8Ø
A 175
6Ø
3
8Ø
A 175
10Ø
12x12
PROVIDE AND INSTALL ROOFTOP UNIT AND CURB
MAINTAINING ALL MANUFACTURER'S CLEARANCES.
MAINTAIN 10' CLEARANCE FROM ALL BUILDING EXHAUST.
SEE DETAIL.
20x14
2
5
8Ø
14Ø
FLEX DUCT
DIAMETER "D"
8Ø
ROUND SHEET
METAL DUCT.
NOTE:
FLEX DUCT TURN INTO DIFFUSER TO BE REPLACED
BY INSULATED SHEET METAL ELBOW FOR (3)
FARTHEST CEILING DIFFUSERS FROM AIR
HANDLER. THERMAFLEX "FLEX FLOW ELBOW"
SUPPORT MAY BE USED IN LIEU OF SHEET METAL
ELBOW.
(RTU-1)
5
E 14Ø
745
6Ø
VOLUME DAMPER WITH
3/8" LOCKING QUADRANT
AND END BEARING.
(WHERE ACCESIBLE)
SUPPLY AIR DUCT.
4Ø EXHAUST DUCT UP TO MFG ROOF JACK WITH BDD
AND INSECT SCREEN. INSTALL ROOF JACK ABOVE
EMERGENCY ROOF DRAIN HEIGHT. MAINTAIN 10'
CLEARANCE FROM ALL BUILDING AIR INTAKES.
10x10
1
5
8Ø
A 175
14Ø E
745
6Ø
5
C 12x10
300
4
4
C 12x10
300
4
C 12x10
300
Manicure Area
REVISIONS
ECONOMIZER HOOD WITH
FILTER ACCESS PANEL.
ROOF TOP MOUNTED
AIR HANDLING UNIT.
HIGH DENSITY
GASKET 2" WIDE.
1" CONDENSATE
TO SPLASH BLOCK
G
FAN
SEAL ALL DUCTWORK
OPENINGS WITH NONHARDENING MASTIC.
EXHAUST FAN (CEILING) DETAIL
NO SCALE
GAS PIPING ON ROOF
6x10
EF-2
10
(RTU-1)
6
6x10
6x8
6x8
9
EXHAUST DUCT FLANGE
FASTENED TO NAILOR
Reception
DATE
MAR. 18, 2014
FLASHING
DRAWN BY
BTM
BACK DRAFT DAMPER
SEAL GAP BETWEEN
FAN HOUSING & CEILING
NOTES:
1. IF FAN IS EQUIPPED W/ INTERNAL BDD ENSURE BDD IS NOT
TAPED SHUT.
2. ENSURE NO PORTION OF TAPE, SEALING, ETC EXTENDS PAST
EDGE OF EXHAUST GRILLE.
3. INSTALLATION IN HARD-CEILING SIMILAR. FAN TO BE
FASTENED TO RAFTER/JOIST. SEE MFG INSTRUCTIONS.
4
FLEX CONN.
D 12x6
200
10
MFG. ROOF CURB
W/ 1" INSUL. & NAILOR
EXHAUST DUCT
EXHAUST GRILLE
6
EXHAUST FAN
6x8
FLASHING
GAS SHUT-OFF VALVE
BY MECHANICAL CONTR.
6x8
2" RIGID INSUL.
CEILING
D 12x6
200
FRESH AIR INLET
PREFABRICATED
ROOF CURB.
HANGER
PROJECT NO.
MDB-1402
PROVIDE ACOUSTIC
DUCT LINER FIRST 10' FROM
DISCHARGE AND INTAKE.
3
PROVIDE 3 ALT. LAYERS OF 5/8"
G.W.B. & 1" RIGID INSULATION.
SEAL AND STAGGER ALL SEAMS.
GAS/ELEC ROOFTOP UNIT
NO SCALE
SHEET TITLE
EXHAUST DUCT
2
EXH. FAN DETAIL (ROOF)
NO SCALE
MECHANICAL
PLAN
& DETAILS
1
MECHANICAL PLAN
SCALE: 1/4" = 1'-0"
SHEET
M1.1
2 OF 3
FIRE RATING LEGEND
1-HR WALL
2-HR WALL
maple
ENGINEERING, pllc
RALEIGH, NC 27605
LIC.#: P-0990
P:919-341-4247
F:919-890-3797
3/18/14
MARLIN DESIGN BUILD
PO Box 1852
Cary, NC 27512
Phone: (919) 291-6736
GAS LINE FROM BELOW
GRADE UP TO HEADER.
BY P.C.
PIPE CLAMPS: "UNISTRUT"
#P2600 WITH CUSHION
BETWEEN PIPING &
CLAMP. SIZE TO MATCH
PIPING SIZE
BY M.C.
NOTE:
PROVIDE REGULATOR AT EACH ROOF TOP UNIT
TO PROVIDE GAS PRESSURE AND CAPACITY AS
REQUIRED BY UNIT MANUFACTURER
ROOF TOP UNIT
SHUT-OFF VALVE
PITCH BACK TO SOURCE
12" MAX.
~28FT
NATURAL GAS CALCULATIONS
TABLE 402.4(2)
PIPE SIZE (IN.)
ROOF
4
RTU-1
(60 MBH)
GAS PIPING DETAIL
MAX CAPACITY OF PIPE IN MBH
?? FT
?? FT
1/2"
40 MBH
?? MBH
?? MBH
3/4"
83 MBH
?? MBH
?? MBH
1"
157 MBH
?? MBH
?? MBH
GAS PIPE SUPPORT
EQUIV. LENGTH = 150 FT
BASED UPON CHAPTER 4 OF THE 2012 NORTH CAROLINA FUEL GAS CODE,
LESS THAN 2.0 PSI INLET PRESSURE, 0.5 IN. W.C. PRESSURE DROP.
NO SCALE
1.
2.
3.
4.
VERIFY EXISTING CONDITIONS BEFORE BEGINNING WORK.
M.C. IS TO PROVIDE REGULATOR, FLEX CONNECTION &
SHUT-OFF VALVE AT EACH EQUIPMENT CONNECTION.
COORDINATE AND VERIFY EXACT SIZE AND LOCATION OF
EQUIPMENT GAS CONNECTION(S) BEFORE BEGINNING
WORK.
PROVIDE LABELING ON GAS PIPING AS REQUIRED BY 2012
NCFGC SEC. 401.5 & 401.7.
REVISIONS
GAS METER
LOCATION
AREA OF
WORK
DATE
MAR. 18, 2014
DRAWN BY
RSA
PROJECT NO.
MDB-1402
SHEET TITLE
MECHANICAL
GAS PLAN
H
RT
O
N
3
BUILDING PLAN
NO SCALE
2
GAS RISER
NO SCALE
1
MECHANICAL PLAN- GAS
SCALE: 1/4" = 1'-0"
SHEET
M1.2
3 OF 3
GENERAL ELECTRICAL NOTES
2.
ALL WORK IS TO BE PERFORMED IN ACCORDANCE WITH NEC AND
ALL OTHER APPLICABLE CODES. EC IS TO COORDINATE W/ G.C. IN
REGARDS TO PROJECT TIMELINE, WORK HOURS, AS WELL AS ANY
BONDING OR INSURANCE REQUIREMENTS.
8.
ALL ELECTRICAL & LIGHTING EQUIPMENT SHALL BE PROVIDED
COMPLETE WITH ALL ACCESSORIES, HANGERS, SUPPORTS,
CONTROLS, ETC FOR A FULLY FUNCTIONING SYSTEM REGARDLESS OF
PRESENCE ON PLANS.
9.
ALL EQUIPMENT, MATERIALS AND INSTALLATION SHALL BE
GUARANTEED TO BE FREE OF DEFECTS FOR A PERIOD OF ONE (1)
YEAR AFTER FINAL ACCEPTANCE OF WORK OR IN ACCORDANCE
WITH THE MANUFACTURER'S STANDARD GUARANTEE, IF LONGER.
EXISTING EQUIPMENT IS EXCLUDED FROM WARRANTY REQUIREMENT.
10.
DO NO SCALE DRAWINGS FOR MEASUREMENT.
7.
INFORMATION GIVEN IN SCHEDULES INCLUDES BOTH DESCRIPTION
OF PRODUCT AND MANUFACTURER'S MODEL #. IF CONFLICT IS
PRESENT BETWEEN DESCRIPTION AND MODEL #, EQUIPMENT
DESCRIPTION SHALL TAKE PRECEDENT. IN CASE OF CONFLICT
BETWEEN THE PLANS AND NOTES/SPECIFICATIONS OR CONFLICT
BETWEEN INFORMATION PRESENTED ON THE PLANS OR IN THE
NOTES/SPECIFICATIONS, THEN THE MOST RESTRICTIVE SHALL TAKE
PRECEDENT.
8.
9.
BEFORE BID EC IS RESPONSIBLE FOR CLARIFYING W/ G.C. ANY
CONFUSION IN REGARDS TO RESPONSIBILITY OF WORK TO BE
PERFORMED OR MATERIALS TO BE PROVIDED. THE SUBMITTAL OF THE
BID BY THE CONTRACTOR WILL BE HELD AS PROOF THAT THE
CONTRACTOR UNDERSTANDS THOROUGHLY AND COMPLETELY THE
SCOPE OF THE WORK INVOLVED, AND HAS INCLUDED ON THE BID
ALL THE NECESSARY ITEMS TO CARRY OUT THIS SECTION OF WORK.
ALL EXISTING EQUIPMENT AND SYSTEMS ARE ASSUMED BY ENGINEER
TO BE IN GOOD WORKING ORDER. BEFORE BEGINNING WORK E.C.
IS TO ENSURE ANY EQUIPMENT & SYSTEMS TO REMAIN ARE PROPERLY
FUNCTIONING. NOTIFY G.C. IMMEDIATELY IF PROBLEMS ARE
DISCOVERED.
10. ALL QUESTIONS MUST BE SUBMITTED IN RFI FORMAT TO THE
ARCHITECT AND MUST BE ADDRESSED BY THE APPROPRIATE
DESIGNER OF RECORD PRIOR TO BECOMING A PROPOSED CHANGE
ORDER.
11. E.C. IS TO REVIEW COMPLETE DRAWING SET. E.C. IS RESPONSIBLE FOR
WORK EXPLICITLY SHOWN AND WORK IMPLIED. UNLESS OTHERWISE
NOTED FINAL ELECTRICAL CONNECTION TO ALL EQUIPMENT,
FURNITURE (I.E. CUBICLES, WORKSTATIONS, ETC) IS THE RESPONSIBILITY
OF THE E.C..
12.
ALL EXTERIOR FIXTURES AND DEVICES SHALL BE RATED FOR
OPERATION AT 0° F AND SHALL BE DAMP OR WET LABELED AS
REQUIRED.
13.
ANY RECESSED LIGHT FIXTURES INSTALLED IN INSULATED CEILINGS
OR WALLS TO BE "IC RATED" AND MEET REQUIREMENTS OF ASTME
283 AND 2012 NCECC SEC. 502.4.8.
1.
2.
3.
4.
5.
6.
ALL ROOF WORK INCLUDING PENETRATIONS, OPENINGS, FLASHING,
CURB INSTALLS, ETC ARE TO BE PERFORMED BY ROOFING
CONTRACTOR. E.C. RESPONSIBLE FOR PROVIDING ANY ROOF
CURBS, EQUIPMENT RAILS, VENTS, ETC AND COMMUNICATING ALL
REQ'S WITH G.C. & ROOFING CONTRACTOR.
ALL LOW VOLTAGE WIRING RELATED TO MECHANICAL EQUIPMENT
AND SYSTEMS IS THE RESPONSIBILITY OF THE MECHANICAL
CONTRACTOR (ANY LOW VOLTAGE FIRE ALARM WIRING TO BE BY
E.C.). ALL HIGH VOLTAGE CONNECTIONS TO MECHANICAL
EQUIPMENT, TO BE PROVIDED AND INSTALLED BY E.C. (SEE
EQUIPMENT SCHEDULE FOR DISCONNECT RESPONSIBILITY).
2.
E.C. TO COORDINATE ELEVATION OF WALL MOUNTED LIGHTS
(INTERIOR & EXTERIOR) W/ ARCHITECT/ARCH PLANS.
3.
E.C. TO COORDINATE W/ P.C. & M.C. REGARDING POWER AND
FIRE ALARM CONNECTIONS TO MECHANICAL AND PLUMBING
EQUIPMENT.
4.
E.C. TO VERIFY ALL REQUIREMENTS AND COORDINATE EXACT
LOCATION OF INCOMING ELECTRICAL SERVICE WITH LOCAL
POWER COMPANY PRIOR TO PROJECT START-UP. NOTIFY
ENGINEER OF ANY CHANGES AS MAY BE REQUIRED.
V. EXECUTION:
1.
E.C. TO FOLLOW MANUFACTURER'S INSTRUCTIONS WHEN
INSTALLING ELECTRICAL EQUIPMENT. ENSURE REQUIRED
MAINTENANCE ACCESS AND CLEARANCES ARE MAINTAINED. IF
CONFLICT EXISTS BETWEEN THESE PLANS AND MFG INSTRUCTIONS
CONTACT ENGINEER.
2.
A COMPLETE GROUNDING SYSTEM SHALL BE PROVIDED AND
INSTALLED IN ACCORDANCE WITH ARTICLE 250 OF THE NEC,
AND AS SHOWN ON THE DRAWINGS.
PROVIDE A TYPED DIRECTORY IN ALL PANELBOARDS CLEARLY
DESCRIBING THE LOCATION OF AND TYPE OF LOAD BEING
SERVED FOR ALL CIRCUITS. PROVIDE ENGRAVED PHENOLIC
NAMEPLATES FOR ALL PANELBOARDS AND DISCONNECT
SWITCHES, WHITE LETTERS ON BLACK BACKGROUND.
5.
SEAL ALL PENETRATIONS OF SMOKE PARTITIONS OR FIRE RATED
WALLS, CEILING, FLOORS IN ACCORDANCE W/ APPROPRIATE
U.L. PENETRATION DETAIL AND NC BUILDING CODE.
ELECTRICAL CONTRACTOR IS TO EMPLOY THE SERVICES OF THE G.C.
FOR CUTTING AND PATCHING OF WALLS, FLOORS & CEILINGS
RELATED TO THE INSTALLATION OF ELECTRICAL EQUIPMENT &
SYSTEMS.
PENETRATIONS OF NON-RATED WALLS, PARTITIONS AND FLOOR
OF COMBUSTIBLE CONSTRUCTION SHALL BE FIRESTOPPED WITH
MATERIALS EQUIVALENT TO TWO INCHES OF WOOD.
FIRESTOPPING SHALL COMPLY WITH ASTM E-814.
8.
G.C. RESPONSIBLE FOR PAINTING OF ANY EXPOSED CONDUIT, WIRE,
BOXES ETC. E.C. RESPONSIBLE FOR CLEANING AND PREPARING
ITEMS FOR PAINT, COORDINATE W/ G.C.
ANY NOTCHING, DRILLING, BORING OR OTHER ALTERATION TO
BUILDING STRUCTURE SHALL BE PERFORMED IN A CODE
APPROVED METHOD AND NOT THREATEN THE INTEGRITY OF THE
BUILDING STRUCTURE.
9.
E.C. TO COORDINATE W/ G.C. PRIOR TO BID REGARDING HIRING OF
FIRE ALARM, DATA/TELE & SECURITY SUB-CONTRACTORS (IF
APPLICABLE).
SUPPORT ALL CONDUIT AND EQUIPMENT IN ACCORDANCE W/
NEC. ANY SUSPENDED MATERIALS SHALL BE DIRECTLY SUPPORTED
BY THE BUILDING STRUCTURE.
10.
PENETRATIONS OF ALL EXTERIOR WALLS, FLOORS AND CEILINGS
SHALL BE SEALED IN AN AIR TIGHT MANNER AND IN
ACCORDANCE W/ 2012 NCECC APPENDIX 2 DETAILS.
11.
THE ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE FOR
PROTECTING ALL ELECTRICAL EQUIPMENT FROM FOREIGN
MATERIAL DURING CONSTRUCTION (PAINT, SPACKLE, ETC.).
UPON COMPLETION OF WORK THE ELECTRICAL CONTRACTOR
SHALL CLEAN, WASH, ETC ALL ITEMS AND EQUIPMENT WITHIN HIS
ALL MATERIAL, DEVICES, APPLIANCES, AND EQUIPMENT SHALL BE
NEW UNLESS OTHERWISE NOTED AND SHALL CONFORM TO THE
STANDARDS OF THE UNDERWRITER'S LABORATORIES, INC., AND THE
NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION.
ALL MATERIALS INSTALLED IN RETURN PLENUM ARE TO BE PLENUM
RATED.
PROVIDE HANGERS & SUPPORTS APPROVED FOR USE BY NEC.
4.
ALL FIRE SEALANTS TO BE U.L. LISTED AND APPROVED FOR USE W/
APPROPRIATE U.L. PENETRATION DETAIL.
CONDUCTORS SHALL BE COPPER RATED AT NOT LESS THAN 600
VOLTS.MINIMUM SIZE SHALL BE #12 AWG UNLESS OTHERWISE NOTED
ON THE DRAWINGS. ALL WIRE #8 AWG AND LARGER SHALL BE
STRANDED. ALL CONDUCTORS #10 AND SMALLER MAY BE SOLID OR
STRANDED, UNLESS OTHERWISE NOTED. CONDUCTOR INSULATION
SHALL BE TYPE THHN UNLESS OTHERWISE NOTED. ALL EXTERIOR CABLE
OR OTHER WIRE EXPOSED TO SUNLIGHT SHALL BE RATED FOR
EXTERIOR USE & SUNLIGHT RESISTANT.
ALL WIRING SHALL BE INSTALLED IN GALVANIZED RIGID CONDUIT,
INTERMEDIATE METAL CONDUIT, OR EMT, EXCEPT AS ALLOWED
BELOW. EMT SHALL NOT BE USED IN OR UNDER CONCRETE SLABS,
OR IN MASONRY WALLS. USE SCHEDULE 40 PVC OUTDOORS WHERE
NOT SUBJECT TO PHYSICAL DAMAGE OR BELOW FLOOR SLAB.
MINIMUM CONDUIT SIZE TO BE 1/2". TYPE MC AND AC CABLE MAY
BE USED WHERE PERMISSIBLE BY NEC. FLEXIBLE CONDUIT SHALL BE
USED FOR CONNECTIONS TO VIBRATING EQUIPMENT AND
LUMINAIRES, BUT SHALL NOT EXCEED 6' IN LENGTH.
12.
13.
14.
INPUT
WATTS
TYPE
MOUNTING
DESCRIPTION
CIRCUIT CONDUCTORS CONCEALED IN FLOOR, WALL OR CEILING.
2x4 2-LAMP ACRYLIC LENSED LAY-IN RECESSED
TROFFER
LITHONIA
2SP8 G
2
32W T8
MVOLT
1
GEB10RS
64
LAY-IN
B
GOTHAM
AFV
1
13W TRT
MVOLT
1
ELECTRONIC
13W
RECESSED
4" RECESSED CAN/DOWNLIGHT. NO LENS
48" LED STRIP LIGHT. INSTALL IN COVE, COORD W/
ARCH. DIMMABLE.
ARROWHEAD INDICATES HOMERUN TO PANEL NOTED.
INDICATES HOT LEG OF CIRCUIT TO BE CARRIED OVER TO NEXT DEVICE. SEE PLANS FOR
CONTROL SCHEME.
IN REQUIRED FIRE RATED WALLS AND PARTITIONS, OPENINGS FOR
INSTALLATION OF BOXES THAT ARE GREATER THAN 16 SQUARE
INCHES SHALL BE PROTECTED AS REQUIRED BY U.L.
UNLESS OTHERWISE INDICATED THE ELECTRICAL CONTRACTOR AT
HIS/HER DISCRETION MAY COMBINE MULTIPLE CIRCUITS INTO A
SINGLE CONDUIT AND DE-RATE WIRE. COMBINING AND
DE-RATING IS TO BE DONE IN STRICT ACCORDANCE W/ NEC.
DEVICES INCLUDING GFCI PROTECTION MUST HAVE THEIR
TESTING MEANS READILY ACCESSIBLE. PROVIDE REMOTE TESTING
MEANS OR GFCI BREAKER FOR GFCI RECEPTACLES AND SIMILAR
DEVICES WHICH ARE NOT READILY ACCESSIBLE (I.E. BEHIND
EQUIPMENT, AT CEILING, ETC). (NEC 210.8).
15.
ALL EXIT & EMERGENCY LIGHTS ARE TO BE CIRCUITED TO
UN-SWITCHED LEG OF LOCAL NORMALLY ON LIGHTING CIRCUIT.
16.
RECEPTACLE, LIGHT SWITCHES AND OTHER CONTROL DEVICES
ARE TO BE INSTALLED IN ACCORDANCE W/ ANSI A117.1 AND
ADA REQ'S CONCERNING HEIGHT AND ACCESSIBILITY. FHA REQ'S
TO BE FOLLOWED FOR MULTI-FAMILY AND RESIDENTIAL
PROJECTS.
17.
E.C. IS TO CONFIRM EXACT ELECTRICAL NAMEPLATE DATA OF
ALL PLUMBING, MECHANICAL AND ELECTRICAL EQUIPMENT
INCLUDING, BUT NOT LIMITED TO, MCA, MOCP, VOLTAGE &
PHASE BEFORE BEGINNING WORK.
maple
ENGINEERING, pllc
RALEIGH, NC 27605
LIC.#: P-0990
P:919-341-4247
F:919-890-3797
JUNCTION BOX CEILING MOUNTED.
C
LITHONIA
ZL1
1
32W LED
MVOLT
1
DRIVER
32W
SURFACE
D
LITHONIA
ZL1
1
32W LED
MVOLT
1
DRIVER
32W
SURFACE
E
-
-
-
-
120
-
-
20W
MAX
WALL
F
-
-
-
-
120
-
-
30W/FT
MAX
TRACK
G
-
-
-
-
120
-
-
50W
MAX
CHANDELIER
E
EMG
J
LITHONIA
LHQM
2
5.4 W T-5
120,
277
-
-
3.3
CEILING
LITHONIA
LQC
1
LED
120,
277
-
-
1.2
CEILING
EXIT LIGHT W/ BATTERY BACK-UP. RED ILLUMINATED
EXIT SIGN. ALUM. FACE. HOUSING COLOR BY ARCH.
LITHONIA
ELAT QWP
2
1.5W LED
120,
277
-
-
-
SEE PLAN
REMOTE EXTERIOR EMERGENCY LIGHT. TWIN HEAD.
BATTERY BACK-UP (CAN BE WIRED TO EXIT UNIT).
WET LOCATION LISTED.
LITHONIA
ELM2
2
5.4 W
120,
277
-
-
1.2
SEE PLAN
GEN. PURPOSE EMERGENCY LIGHT. (2) ADJ. HEADS.
BATTERY BACK-UP.
-
-
-
-
120,
277
-
-
MFG
CONCEALED
SINGLE POLE SWITCH, 20A, 120/277 VOLT, 48" A.F.F. TO CENTER.
"3" INDICATES 3-WAY SWITCH.
"4" INDICATES 4-WAY SWITCH.
"D" INDICATES DIMMER SWITCH OF TYPE TO SUIT LOAD.
"M" INDICATES 120V, 20A MOTOR RATED TOGGLE SWITCH.
"DP" INDICATES DOUBLE POLE
INDICATES FLUORESCENT FIXTURES DUAL SWITCHED, INBOARD/OUTBOARD SWITCHED
SEPARATELY.
DUPLEX RECEPTACLE, 20 AMP (15 AMP RESIDENTIAL, UON), 120 VOLT, 18" A.F.F. TO CENTER.
"GFI" INDICATES GROUND FAULT CIRCUIT INTERRUPTER TYPE.
"WP" INDICATES WEATHERPROOF.
"EWC" INDICATES RECEPTACLE INSIDE ENCLOSURE OF ELECTRIC WATER COOLER PROVIDE
GFI BREAKER FOR CIRCUIT.
"ASW" INDICATES ABOVE SHOW WINDOW, PER NEC SHOW WINDOW REQ'S.
DUPLEX RECEPTACLE, AS ABOVE, SPLIT WIRED, TOP HALF SWITCHED, 18" A.F.F.
DUPLEX RECEPTACLE, AS ABOVE, MOUNTED 6" ABOVE COUNTER TOP OR 4" ABOVE
BACKSPLASH, AS APPROPRIATE, OR AT HEIGHT INDICATED.
DUPLEX RECEPTACLE, AS ABOVE, MOUNTED 6" ABOVE COUNTER TOP OR 4" ABOVE
BACKSPLASH, AS APPROPRIATE, OR AT HEIGHT INDICATED, WITH GFI PROTECTION.
RECESSED FLUSH FLOOR DUPLEX RECEPTACLE WITH BRASS COVERPLATE. COORDINATE
EXACT FINISH WITH ARCHITECT AND OWNER.
208V RECEPTACLE, SEE PLANS FOR NEMA CONFIGURATION.
TELEPHONE/DATA OUTLET, 18" A.F.F. TO CENTER OR ALIGN MOUNTING HEIGHT WITH
ADJACENT DEVICE, UNLESS OTHERWISE NOTED. COORDINATE EXACT DEVICE TYPE AND
REQUIRED FACEPLATE W/ OWNER/TENANT.
LIGHTING SYSTEMS
INTERIOR WATTAGE SPECIFIED VS. ALLOWED
1,683 VS. 1,692
EXTERIOR LIGHTING POWER DENSITY CALCULATION PER TABLE 505.6.2. SEE LIGHTING
FIXTURE SCHEDULE FOR FIXTURE INFORMATION.
TRADABLE EXTERIOR WATTAGE SPECIFIED VS. ALLOWED
NONTRADABLE EXTERIOR WATTAGE SPECIFIED VS. ALLOWED
30/3/FPN
DESIGNER STATEMENT:
TO THE BEST OF MY KNOWLEDGE AND BELIEF, THE DESIGN OF THIS BUILDING COMPLIES
WITH THE LIGHTING SYSTEMS REQUIREMENTS OF THE NORTH CAROLINA ENERGY
CONSERVATION CODE, SECTION 505 & 506 AND ANY LOCAL AMENDMENTS THEREOF.
INTERIOR LIGHTING POWER DENSITY CALCULATION PER TABLE 505.5.2. SEE LIGHTING
FIXTURE SCHEDULE FOR FIXTURE INFORMATION.
EXIST. VS. EXIST.
NA VS. NA
PO Box 1852
Cary, NC 27512
Phone: (919) 291-6736
QUADRUPLEX RECEPTACLE, AS ABOVE, 18" A.F.F.
EMERGENCY BATTERY PACK. COORDINATE W/
FIXTURE TYPE/MFG. PROVIDE TEST SWITCH/LIGHT.
NCECC SECTION 505 & 506
3/18/14
MARLIN DESIGN BUILD
SINGLE RECEPTACLE, 20 AMP, 120 VOLT, 18" A.F.F. TO CENTER.
NOTES:
1. UNLESS OTHERWISE NOTED COLOR & FINISH OF FIXTURE HOUSING, BAFFLE, OR SIMILAR EXPOSED ELEMENTS TO BE BY ARCHITECT.
2. WHERE MASTER SLAVE WIRING CONFIGURATIONS IS INDICATED THE CONTRACTOR SHALL VERIFY THE QUANTITY AND TYPE OF BALLASTS REQUIRED TO PERMIT BI-LEVEL SWITCHING. WHERE
BI-LEVEL LIGHTING IS INDICATED INBOARD AND OUTBOARD LAMPS SHALL BE SWITCHED SEPARATELY.
3. EXIT AND EMERGENCY LIGHTING FIXTURES SHALL BE CIRCUITED TO AN UNSWITCHED LEG OF A NORMALLY ON LOCAL LIGHTING CIRCUIT (UNLESS NOTED OTHERWISE),INCLUDE 90 MINUTE BATTERY
BACKUP & TESTING MEANS.
4. PROVIDE DISCONNECT FOR LUMINAIRES WITH LINEAR FLUORESCENT LAMPS AND/OR SERVICEABLE BALLASTS PER NEC 410.130(G).
5. FIXTURES WITH A STANDARD FACTORY INSTALLED EMERGENCY OPTION SHOULD USE THAT WHERE "EMC" IS SHOWN.
6. ALL LAMPS OF A SINGLE FIXTURE TYPE INSTALLED IN EACH AREA/ROOM/SPACE ARE TO BE OF SAME TEMPERATURE/COLOR.
LIGHTING POWER DENSITY CALCULATION COMPLIANCE
JUNCTION BOX FLOOR MOUNTED.
JUNCTION BOX WALL MOUNTED AT HEIGHT INDICATED ON DRAWINGS.
24" LED STRIP LIGHT. INSTALL IN COVE, COORD W/
ARCH. DIMMABLE.
WALL SCONCE LIGHT. SELECTED BY OTHERS.
PROVIDED & INSTALLED BY E.C.. INCLUDE
$100/FIXTURE MAT'L ALLOWANCE IN BID.
TRACK LIGHT. SELECTED BY OTHERS. PROVIDED &
INSTALLED BY E.C.. INCLUDE $75/TRACK HEAD MAT'L
ALLOWANCE IN BID.
CHANDELIER LIGHT. SELECTED BY OTHERS.
PROVIDED & INSTALLED BY E.C.. INCLUDE
$300/FIXTURE MAT'L ALLOWANCE IN BID.
EXIT-EMERGENCY LIGHT COMBO. (2) ADJ. HEADS.
BATTERY BACK-UP. RED ILLUMINATED EXIT SIGN.
HOUSING COLOR BY ARCH.
HEAVY DUTY FUSIBLE/NON-FUSIBLE DISCONNECT SWITCH, NUMBERS INDICATE FRAME SIZE,
NUMBER OF POLES AND FUSING. PROVIDE NEMA 1 ENCLOSURE INSIDE. PROVIDE NEMA 3
ENCLOSURE FOR ALL SWITCHES LOCATED OUTSIDE.
"FPN" INDICATES FUSE PER EQUIPMENT NAMEPLATE
"NF" INDICATES NON-FUSED.
"MS" INDICATES MOTOR STARTER OF TYPE TO SUIT LOAD.
208Y/120V PANEL, SURFACE OR RECESS MOUNTED, SEE SCHEDULE FOR DETAILS.
SIGNED:
NAME:
ZACK L. TOMLIN, PE
TITLE:
ELECTRICAL ENGINEER
480Y/277V PANEL, SURFACE OR RECESS MOUNTED, SEE SCHEDULE FOR DETAILS.
EF
FAN, PROVIDED AND INSTALLED BY MECHANICAL CONTRACTOR, WIRED BY ELECTRICAL
CONTRACTOR. PROVIDE DISCONNECTING MEANS AS REQUIRED.
RECESSED MOUNTED 2x4 FLUORESCENT TROFFER, SEE FIXTURE SCHEDULE FOR DETAILS.
ADDITIONAL PRESCRIPTIVE COMPLIANCE
NOT APPLICABLE (RENOVATION PROJECT)
506.2.1 MORE EFFICIENT MECHANICAL EQUIPMENT
506.2.2 REDUCED LIGHTING POWER DENSITY
506.2.3 ENERGY RECOVERY VENTILATION SYSTEM
506.2.4 HIGHER EFFICIENCY SERVICE WATER HEATING
506.2.5 ON-SITE SUPPLY OF RENEWABLE ENERGY
506.2.6 AUTOMATIC DAYLIGHTING CONTROL SYSTEMS
X
TRACK LIGHTING FIXTURE, SEE FIXTURE SCHEDULE FOR DETAILS.
SURFACE MOUNTED FLUORESCENT STRIP, SEE FIXTURE SCHEDULE FOR DETAILS.
WALL MOUNTED LIGHTING FIXTURE, SEE FIXTURE SCHEDULE FOR DETAILS.
ALL PENETRATIONS THROUGH EXTERIOR WALLS & ROOF SHALL BE
FLASHED & COUNTER-FLASHED IN A WATERPROOF MANNER.
6.
3.
6.
PROVIDE A PULLWIRE IN ALL EMPTY CONDUITS.
4.
7.
2.
5.
3.
G.C. TO BE RESPONSIBLE FOR PROVIDING AND INSTALLING ANY
ACCESS DOORS (WALL, FLOOR, CEILING) RELATED TO ELECTRICAL
SYSTEM. E.C. RESPONSIBLE FOR COMMUNICATING TO G.C. SIZE AND
LOCATION OF REQ'D ACCESS DOOR(S).
III. MATERIALS:
1.
THE ELECTRICAL CONTRACTOR SHALL COORDINATE CLOSELY
WITH ALL OTHER TRADES TO AVOID CONFLICT AND ENSURE
OTHER TRADES PROVIDE MEASURES TO ACCOMMODATE
ELECTRICAL WORK (I.E. ACCESS DOORS, SLAB/WALL/ROOF
OPENINGS, ETC).
BALLAST DATA
NO.
A
IV. COORDINATION:
1.
LIGHTING SWITCHES SHALL BE 20 AMP COMMERCIAL
SPECIFICATION GRADE EQUAL TO HUBBELL SERIES.
VOLTS
TYPE
SURFACE, RECESSED OR GROUND MOUNTED LIGHTING FIXTURE, SEE FIXTURE SCHEDULE FOR
DETAILS.
M
###
ELECTRIC UTILITY METER LOCATION.
KITCHEN EQUIPMENT TAG.
DEMO'D LIGHT FIXTURE OR SIMILAR.
DEMO'D RECEPTACLE OR SIMILAR.
TV
CABLE TV OUTLET, 18" A.F.F. TO CENTER, UNLESS OTHERWISE NOTED.
ELECTRICAL ABBREVIATIONS
18"
CEILING
FIRE ALARM HORN,
HORN/STROBE OR
STROBE.
AFF
NOTE:
DEVICE HEIGHTS ARE TO
BE AS INDICATED UNLESS
OTHERWISE NOTED.
FIRE
ALIGN DEVICES WHEN
MOUNTED CLOSE ON
SAME WALL
WALL
MOUNTED
TELEPHONE
RECEPTACLE
LIGHT SWITCH
OR DIMMER
TELE/DATA
SWITCH
FIRE ALARM
PULL STATION
RECEPTACLE
TELEPHONE OR
DATA JACK
TOP OF COUNTER
42"
6.
11.
NO.
80"
THESE DRAWINGS ARE DIAGRAMMATIC AND SHOW GENERAL
LOCATION AND ARRANGEMENT OF ALL MATERIALS AND
EQUIPMENT. THE DRAWINGS SHALL BE FOLLOWED AS CLOSELY AS
BUILDING CONSTRUCTION AND ALL OTHER WORK WILL PERMIT.
RECEPTACLES IN COMMERCIAL AREAS SHALL BE 20 AMP
COMMERCIAL SPECIFICATION GRADE EQUAL TO HUBBELL SERIES.
GROUND FAULT RECEPTACLES SHALL BE EQUAL TO COOPER VGF
SERIES.
LAMP DATA
CATALOG
NUMBER
48"
5.
ALL TERMINALS/LUGS SHALL BE 60/75° RATED. ALL TERMINALS,
SPLICING CONNECTORS, LUGS, ETC SHALL BE IDENTIFIED FOR USE
WITH THE MATERIAL (CU/AL) OF THE CONDUCTOR AND SHALL BE
PROPERLY INSTALLED.
MANUF.
46"
4.
FUSES 0 - 600 AMPS SHALL BE UL CLASS "RK-1" LOW PEAK DUAL
ELEMENT TIME DELAY WITH 200,000 AMPERE INTERRUPTING
RATING AS MANUFACTURED BY BUSSMANN, UNLESS NOTED
OTHERWISE.
ELECTRICAL SYMBOL LEGEND
LIGHTING FIXTURE SCHEDULE
MARK
46"
3.
METAL CONDUIT COUPLINGS TO BE COMPRESSION TYPE OR
THREADED WHEN ACCESSIBLE TO BUILDING OCCUPANTS. METAL
COUNDUIT COUPLINGS MAY BE SET-SCREW TYPE WHEN
CONCEALED IN BUILDING STRUCTURE OR LOCATED MORE
THAN 10' AFF. PLASTIC CONDUIT COUPLINGS TO BE SOCKET
GLUED TYPE.
36" MAX
7.
ELECTRICAL CONTRACTOR IS TO FURNISH AND PAY FOR ALL LABOR,
MATERIAL, EQUIPMENT, PERMITS & FEES REQUIRED FOR THE
COMPLETE INSTALLATION OF ALL SYSTEMS IN THIS SECTION OF
WORK.
MAX COUNTER
DEPTH = 24"
18"
1.
FLOOR
NOTE:
MOUNTING LOCATIONS OF RECEPTACLES, SWITCHES AND ALL
OTHER CONTROL DEVICES SHALL BE IN ACCORDANCE WITH
ANSI A117.1 AND ADA REQUIREMENTS (FHA REQ'S FOR
MULTI-FAMILY AND RESIDENTIAL PROJECTS)
1
TYPICAL DEVICE MOUNTING HEIGHTS
NO SCALE
ABOVE FINISHED FLOOR.
AFG
ABOVE FINISHED GRADE.
E.C.
ELECTRICAL CONTRACTOR.
FPN
FUSE PER EQUIPMENT NAMEPLATE REQUIREMENTS.
G.C.
GENERAL CONTRACTOR.
M.C.
MECHANICAL CONTRACTOR.
P.C.
PLUMBING CONTRACTOR.
WP
INDICATES DEVICE TO HAVE WEATHERPROOF COVER.
UON
UNLESS OTHERWISE NOTED.
FACP
FIRE ALARM CONTROL PANEL.
SMP
SPRINKLER MONITORING PANEL.
NL
NIGHT LIGHT, LIGHT NOT SWITCHED.
WP
WEATHER PROOF
MOTION SENSOR LEGEND
M0
REVISIONS
DIMENSION INDICATES HEIGHT ABOVE FINISHED FLOOR AT WHICH CENTER OF
DEVICE IS TO BE MOUNTED.
DATE
MAR. 18, 2014
DRAWN BY
MJL
PROJECT NO.
MDB-1402
SHEET TITLE
ELECTRICAL
SCHEDULES
DETAILS &
NOTES
WALL SWITCH MICROPHONIC OCCUPANCY SENSOR EQUAL TO SENSOR SWITCH MODEL WS
PDT. TIME DELAYS 10 MINUTES FOR ON/OFF.
NOTE:
THE CONTRACTOR IS TO PROVIDE AND INSTALL ALL RELAYS, CONTROLS, SWITCHES, ETC FOR
A FULLY FUNCTIONING SYSTEM REGARDLESS OF PRESENCE OR ABSENCE ON PLANS.
NOTE:
THE MOTION SENSOR LAYOUT SHALL BE REVIEWED AND ADJUSTED BY THE ACTUAL DEVICE
MANUFACTURER WHICH THE CONTRACTOR SELECTS. THE CONTRACTOR SHALL PROVIDE
SHOP DRAWINGS FOR THE SYSTEM TO THE ENGINEER FOR REVIEW, PRIOR TO PURCHASE AND
INSTALLATION.
SHEET
E0.1
1 OF 3
FIRE RATING LEGEND
1-HR WALL
2-HR WALL
maple
ENGINEERING, pllc
ALL PEDICURE CHAIRS TO BE U.L. LISTED.
RALEIGH, NC 27605
LIC.#: P-0990
P:919-341-4247
F:919-890-3797
PEDICURE CHAIR
=BONDING POINT
TO OTHER
CHAIRS
RECEPTACLE PROTECTED BY GFI
BREAKER. SEE PANEL SCHEDULE.
HW LINE
(IF METAL)
CW LINE
(IF METAL)
RECIRCULATING
WATER BASIN
M
E
FINISH FLOOR
1
Passage
RECIRCULATING
PUMP
WASTE LINE
(IF METAL)
4
NOTE: ANY OTHER GROUNDED
METAL COMPONENTS NOT
SHOWN THAT MAKE CONTACT
WITH RECIRCULATING WATER
MUST BE BONDED AS WELL.
A-9
EMG
+48"
A
B
3/18/14
ABV. CEIL.
Restrm
A
A-13,15
EF
WH-1
Passage
60/2/FPN
A
+48"
SOLID COPPER
MIN. 8 AWG
A-17
MARLIN DESIGN BUILD
A-33,35
Restrm
A-8
PEDICURE CHAIR BONDING DETAIL
Office
PO Box 1852
Cary, NC 27512
Phone: (919) 291-6736
A-12
NO SCALE
A
Office
A
B
A-12
M0
M0
A-8
Waxing
Waxing
A-10
DIMMER SWITCH
DIMMER SWITCH
DIMMER SWITCH
SINGLE SWITCH
DIMMER SWITCH
A
SINGLE SWITCH
A
M0
OFF
X
Waxing
C
N
O
P
R
S
FRNT TRACK
A-1
FRNT TRACK
A-3
FRNT TRACK
A-3
MANI. WALL
A-5
MANI. WALL
A-5
2
A-10
D
L
A-32
D
B
Z
U
A-7
5
A-20
EF
A-18
B
SINGLE SWITCH
DIMMER SWITCH
FAN SWITCH
FAN SWITCH
G
A-34
B
C
OFF
B
U
X
Y
Z
PEDI. CANS
A-7
LED STRIP LTS
A-7
EF-MANICURE
A-16
EF-PEDICURE
A-18
EMG
C
A-22
Pedicure Area
B
A-24
C
C
A-38
B
COORDINATE EXACT SWITCH TYPE W/ OWNER AND FIXTURES & BALLAST(S) BEING CONTROLLED.
2.
LABEL SWITCHES W/ DESIGNATION SHOWN (I.E. "A", "AN", "W", ETC) & CIRCUIT #.
3.
PROVIDE PLACARD AT EACH SWITCH INDICATING AREA CONTROLLED.
4.
DIMMER SWITCH TO INCLUDE ON-OFF SWITCH AT BOTTOM TO ALLOW FOR ONE-TIME ADJUSTMENT OF
B
B
A-26
C
C
EMG
1.
HIGHEST POSITION OF HIGHEST SWITCH TO BE NO GREATER THAN 48" AFF (ANSI A117.1)
SEE LEGEND.
ENSURE THAT ALL EXIT AND EMERGENCY LIGHTS ARE
CONNECTED TO LOCAL NORMALLY ON LIGHTING CIRCUIT
AND ARE WIRED UPSTREAM OF ALL SWITCHES,
CONTACTORS, AND SIMILAR.
"C" & "D" FIXTURES TO BE INSTALLED IN RECESSED CEILING
FIXTURE. COORDINATE EXACT LOCATION OF FIXTURES W/
ARCH. & OWNER.
B
D
C
D
SWITCH BANK DETAIL
A-40
EMG
G
B
LIGHT LEVELS.
3
A-36
Pedicure Area
B
EMG
SWITCH BANK NOTES:
1.
5.
A-8
A-37,39,41
B
OFF
FRNT TRACK
A-1
4
RTU-1
Waxing
EMG
2.
B
NO SCALE
3.
R
A-28
A-42
A-30
A-4
A-6
A-5
E
S
Manicure Area
E
F
F
A-3
G
F
F
E
P
E
1
PROPOSED SWITCH BANK LOCATION. CONFIRM W/
OWNER.
2
RECEPTACLE FOR PEDICURE CHAIR. CONFIRM
LOCATION OF RECEPTACLE W/ OWNER. SEE PEDICURE
CHAIR DETAIL.
3
COORDINATE EXACT LOCATION OF RECEPTACLE W/
OWNER & CASEWORK.
4
RTU TO INCLUDE FACTORY MOUNTED DISCONNECT.
AND FACTORY POWERED GFI CONVENIENCE OUTLET.
COORDINATE W/ M.C..
5
EXHAUST FAN LOCATED ON ROOF. CONTROLLED VIA
WALL SPEED CONTROLLER SWITCH PROVIDED BY
M.C.. SWITCH LOCATED IN SWITCH BANK.
6
COORDINATE EXACT LOCATION OF JUNCTION BOX
SIGN CIRCUIT W/ OWNER.
O
F
N
F
G
A-1
Reception
A-4
A-6
Manicure Area
REVISIONS
Y
EF
5
A-4
A-16
A-6
A-2
E
3
Reception
DATE
L
A-2
ASW
A-14
D
MAR. 18, 2014
DRAWN BY
MJL
PROJECT NO.
MDB-1402
E
SHEET TITLE
6
A-11
2
ELEC. LIGHTING PLAN
SCALE: 1/4" = 1'-0"
1
ELEC. POWER PLAN
ELECTRICAL
LIGHTING
& POWER
PLAN
SCALE: 1/4" = 1'-0"
SHEET
E1.1
2 OF 3
maple
ENGINEERING, pllc
RALEIGH, NC 27605
LIC.#: P-0990
P:919-341-4247
F:919-890-3797
PANEL "A" LOAD SUMMARY
LOAD TYPE
kVA
CONN.
LOADS ON 200AMP MCB @ METER
3.6
1.25
4.5
TRACK LIGHTS (28 FT)
2.1
1.25
2.6
1st 10 kVA
2.8
1.0
2.8
REMAINDER
0.0
0.5
0.0
SHOW-WINDOW (7 FT @ 125%)
0.2
8.75
1.8
HVAC & R
ELEC HEAT
0.0
1.0
0.0
LARGEST MOTOR
6.0
1.25
7.5
REMAINDER
WATER HEATER (ELECTRIC)
WASHERS
LAUNDRY EQUIPMENT
DRYERS
# OF ELECTRIC DRYERS: 1
2.5
1.0
2.5
6.0
1.25
7.5
1.0
1.0
1.0
5.0
1.0
5.0
PEDICURE CHAIR
18.0
1.0
18.0
SIGN
1.2
1.25
1.5
EF-1,EF-2
1.0
1.25
1.3
PANEL: A
VOLTAGE: 208Y/120V
kVA
DEM.
LIGHTS (1,200 SQ FT @ 3W/SQ FT > CONN. LOAD)
RECEPTACLES
AMPS: 200-MLO
WIRE
SIZE
BRK
SIZE
LTS: FRONT TRACKS
1
12
20
1
LTS: MANICURE TRACKS
1
12
20
3
LTS:CHANDLRS,WALL SCON.
1
12
20
5
LTS: PEDI. AREA
1
12
20
LTS: BACK OFF,WAX, HALL
1
12
20
1
12
20
TC SIGN
DRYER
GFI WASHER
SPARE
SPARE
SPARE
TOTAL AMPS @
208 V
49.4
3 PHASE
FLUSH MOUNTED
NEMA 1
LOAD PER PHASE
POLE
NOTES -DESCRIPTION-
CKT
#
7
10
30
1
12
20
17
1
-
20
19
1
-
20
21
1
-
20
23
1
-
-
25
1
-
-
27
-
29
1
-
1
-
-
2
8
40
3
8
31
45
1.0
0.6
2.5
0.2
0
1.5
0.8
0.6
0.6
1.2
0.4
0.4
2.5
0.5
0
1.5
0
1.5
3.0
1.5
0
0
0
1.5
0
1.5
3.0
1.5
1.5
35
2.8
0.5
1.5
1.5
39
2.8
1.5
41
2.9
14.7
55.9
0.6
1.0
33
37
RTU-1
1.5
15
SPACE
SPACE
C
0.6
9
SPACE
SPACE
1.0
B
11
13
2
WH-1
A
18.1
TOTAL CONNECTED kVA:
TOTALS
3 PHASE, 4 WIRE
NEXT TO BACK DOOR
DEM.
FACT.
1.5
CKT#
BRK
SIZE
WIRE
SIZE
POLE
1.
2.
3.
4.
NOTES
2
20
12
1
REC: RECEPT/WAITING
4
20
12
1
REC: MANI. AREA RIGHT
6
20
12
1
REC: MANI. AREA LEFT
8
20
12
1
REC: WAXING 103/RESTRM
10
20
12
1
3/18/14
MARLIN DESIGN BUILD
REC: WAXING 105
12
20
12
1
REC: OFFICE
14
20
12
1
REC: SHOW WINDOW
16
20
12
1
18
20
12
1
20
20
12
1
PEDICURE STATION CHAIR GFI
22
20
12
1
24
20
12
1
EF-1
EF-2
26
20
12
1
28
20
12
1
30
20
12
1
32
20
12
1
34
20
12
1
36
20
12
1
38
20
12
1
40
20
12
1
42
20
12
1
PO Box 1852
Cary, NC 27512
Phone: (919) 291-6736
16.2
49.0
DEMAND kVA: 55.9
PANEL RMS SYM. AMPS: SEE RISER
155.2
-DESCRIPTION-
DEMAND AMPS: 155.2
PANEL SHALL BE EQUAL TO SQUARE D NQ.
PROVIDE HACR BREAKERS FOR HVAC EQUIPMENT.
GFI - PROVIDE GFCI BREAKER FOR CIRCUIT. GFCI RECEPTACLES MAY BE USED IN LIEU OF GFCI
BREAKERS SO LONG AS THE DEVICE(S) CONFORM TO NEC CODE REQUIREMENTS FOR GFCI
PROTECTION & ACCESSIBILITY.
TC - CIRCUIT THROUGH 7-DAY PROGRAMMABLE TIME SWITCH WITH AUTO-DUSK, AUTO-DAWN
FEATURE. SWITCH TO INCLUDE MANUAL OVERRIDE.
METER CENTER MAIN BUS - LOAD SUMMARY
SUM OF EXISTING TENANT DISCONNECTS = 1,000A + 153.8A NEW
TENANT LOAD = 1,153.8A < 1,600A MLO.
MAIN SERVICE DISC. - LOAD SUMMARY
SUM OF EXISTING TENANT DISCONNECTS = 1,400A + 153.8A NEW
TENANT LOAD = 1,553.8A < 1,600A MCB.
NOTE 3
NOTE 7
M
M
200A
EXISTING ELECTRICAL SERVICE/METER CENTER. SEE. RISER.
100A
208Y/120V
3Ø/4W
NOTE 6
1,600A
MLO
M
200A
M
150A
M
PANEL
A
200A
200A MLO
208Y/120V
NOTE 10
208Y/120V
3Ø/4W
M
1,600A
MCB
AREA
OF
WORK
NOTE 5
150A
M
200A
M
UTILITY
XFMR
300 kVA
REVISIONS
400A
EXIST.
NOTE 6
MAIN SERVICE
DISCONNECT
GRADE
NAIL SALON
FROM UTILITY
DATE
NOTE 4
2
BUILDING PLAN
N
1
NO SCALE
SHORT CIRCUIT CALCULATION
TX %Z
VOLTAGE
PHASE
3
# COND.
WIRE SIZE
PER Ø
E.C. TO CONFIRM RISER BEFORE BEGINNING WORK. CONTACT ENGINEER IF SIGNIFICANT
3.
(4)#3/0 CU, #6 CU GND, 2" CONDUIT.
DISCREPANCIES ARE FOUND.
4.
E.C. TO CONFIRM PRESENCE OF GROUNDING/BONDING SYSTEM (NEC 250).
5.
EXISTING 1,600 AMP MAIN DISCONNECT. E.C. TO CONFIRM. CONTACT ENGINEER IF OF LESSER
30
26706
6.
2.5
208
MULT.
(ISC)
TX ISC
f
M
ISC (AMPS)
833
40.00
33309
0.1558
0.8652
28819
500 kcmil
ALL EXISTING ITEMS ARE SHOWN IN FAINT. NEW ITEMS ARE SHOWN IN BOLD.
2.
WIRE "C"
300
MAR. 18, 2014
DRAWN BY
MJL
PROJECT NO.
1.
WIRE L.
(FEET)
CURRENT
(L TO L)
2
NO SCALE
RISER DIAGRAM NOTES:
MAXIMUM AVAILABLE FAULT CURRENT IS BASED ON A THE TX KVA, IMPEDANCE (%Z),
WIRE SIZE & LENGTH SHOWN BELOW. CONTRACTOR SHALL NOTIFY ENGINEER
IMMEDIATELY IF TRANSFORMER CHARACTERISTIC INDICATE A HIGHER FAULT CURRENT
IS POSSIBLE (HIGHER KVA, LOWER IMPEDANCE, LARGER SECONDARY WIRE, SHORTER
SECONDARY LENGTH, ETC).
TX KVA
ELECTRICAL POWER RISER
MDB-1402
SHEET TITLE
PANEL
SCHEDULE
& RISER
AMPACITY.
7.
EXISTING EMPTY METER/DISCONNECT BASE.
EXISTING METER BASE. NEW METER BY UTILITY. E.C. TO VERIFY LOCATION OF METER/DISCONNECT
FRAME THAT SERVES CORRESPONDING TENANT SPACE.
8.
PROVIDE PLACARD AT PANEL(S)/DISCONNECT(S) INDICATING SUITE/TENANT & PANEL SERVED.
9.
PROVIDE PLACARD INDICATING AVAILABLE AIC FAULT CURRENT (NEC 110.24)
10. MAIN BREAKER, PANEL AND BRANCH CIRCUIT BREAKERS TO BE PAIRED TO ENSURE 42,000 AIC
RATING IS MAINTAINED THROUGHOUT. COORDINATE W/ EQUIPMENT MFG.
SHEET
E2.1
3 OF 3
ELECTRICAL POWER RISER

mdb-1402 mar. 18, 2014 revisions date drawn by sheet title project

Transcription

Similar documents

Blackman Plumbing Supply`s new Bay Shore, NY branch is now open!

May 2015 - Gulf Coast Plumbing, Heating, Cooling Contractors

Murray Feiss OL7411ASTB

American Society

1-888-EDS-ROTO (337-7686)

Since 1929 - Atlantic Plumbing Supply

HT-METAL QUICKSTART GUIDE

Home Solutions Team - Ohana Lawn Service

Noor Fadzli Yahaya UniKL MICET, 2006

- Hamilton Law Association