Storm Bottom Load Dispenser

Storm
Bottom Load
Dispenser
STORM – Bottom Load
What is the STORM?
  The first Bottom Load dispenser to be marketed in the HOD market
segment.
  Features the patented SmartFlo SF-1 replaceable reservoir system that
provides 100% sanitization.
  Plus many other unique features for differentiation from traditional coolers
and from other bottle load coolers.
d
STORM – Bottom Load
What is the SmartFlo SF-1 Water Cartridge?
 
A removable reservoir system that offers convenient sanitization of all water contact
components.
 
Rather than cleaning and sanitizing the waterways, the entire water contact components
are removed and replaced with a new system.
 
For the best quality and better tasting water, it is recommended that the SmartFlo SF-1 be
exchanged every 6 months.
d
STORM – Bottom Load Cooler
Features:
  Award winning contemporary design
  Appliance look with high gloss finish
  Unique space-saving, sliding front door
  Ergonomic design
  High dispense
  Large dispensing area
  Child resistant hot water handle
  Recessed water outlet
  SmartFlo SF-1 Water Cartridge
d
STORM – Bottom Load Cooler
Features
  100% Sanitization
  Air free reservoir
  Large drip tray
  Low water level indicator
  Replace SmartFlo indicator (optional)
  Reduced equipment handling
  Energy star certified
d
STORM – Initial Set Up
Installing the Water Bottle
①
②
③
 
Open Dispenser door (Figure 1). (slide door upward to allow access to bottle area).
 
Place fresh bottle outside of the cabinet and clean the bottle’s exterior with a clean cloth.
 
Remove bottle cap completely from the top of the bottle (Figure 2).
 
Un-package and assemble the Bottle Adaptor assembly (located in the bottle storage area)
 
Place the bottle adaptor probe into the bottle (Figure 3). It may be necessary to straighten the
tubing so that it reaches the bottom of the bottle. If nitrile gloves are not available, use the
inside of the bag which the adapter came in to straighten the tubing without touching with your
hand.
 
Slide the bottle adaptor over the neck of the bottle and push down to secure (Figure 4).
 
Push probe down until the tube hits the bottom of bottle, taking care that the tube does not get
lodged in the bottle handle, if applicable. (Figure 5).
 
Slide bottle into cabinet and close the door (slide door downward to close {Figure 6}). Place a
container under faucet and dispense water until a smooth stream of water is dispensed. Prime
the cold then the hot side. Once water is dispensed through both faucets, open the door and
turn on the hot tank switch located on the right side (Figure 7).
④
⑤
⑥
⑦
d
STORM – Bottle Change
A flashing red light above the cold water lever will alert you when your water bottle is getting low.
The bottle will need to be replaced shortly. Water may be dispensed normally until empty (no
water flows from water outlet when levers are depressed).
①
②
③
 
Open Dispenser door (Figure 1). (slide door upward to allow access to bottle area).
 
Place fresh bottle outside of the cabinet and clean the bottle’s exterior with a clean cloth.
 
Remove bottle cap completely from the top of the full bottle. (Figure 2)
 
Slide empty bottle out and place side by side with the new full bottle (Figure 3)
 
Remove bottle adaptor from the empty bottle and place directly into the top of the new, full
bottle (Figure 4).
 
Slide the bottle adaptor over the neck of the bottle and push down to secure (Figure 4).
 
Push probe down until the tube hits the bottom of bottle, taking care that the tube does not get
lodged in the bottle handle, if applicable. (Figure 5).
 
Slide bottle into cabinet and close the door (slide door downward to close {Figure 6}).
 
Place a container under faucets and dispense water until water is dispensed separately from
both the cold and hot faucets.
④
⑤
⑥
d