Thermofoil PRO

Transcription

Thermofoil PRO

!
PLEASE ENSURE YOU HAVE READ
AND FULLY UNDERSTOOD THIS
GUIDE BEFORE INSTALLATION!
Thermofoil PRO
Installation Guide
YOUR STEP-BY-STEP GUIDE TO
THE PERFECT INSTALLATION
TFPIG1
INSTALLATION GUIDE: THERMOFOIL PRO
Thank you for your purchase...
A message from customer care
Warranty, Terms & Conditions
Thank you for choosing a Thermogroup UK product. Our commitment to simple,
The Thermogroup UK 15 Year Warranty guarantees Thermofoil PRO Heating Mat
honest, on-time quality service ensures that we are here to help throughout every
to remain free from defects in workmanship and materials under normal use and
stage of your project from idea to installation and, most importantly, after sales
maintenance, and is guaranteed to remain in full working order subject to the
support.
conditions and limitations below:
This document will provide a step-by-step guide to a perfect installation as well
Thermofoil PRO Heating Mat are guaranteed for the lifetime of the floor covering
as details on your warranty and how to get Technical Support should you need it.
under which it is originally fitted subject to the following conditions. Please pay
attention to the exclusions listed at the end of this guarantee.
To ensure a safe, hassle-free installation to be proud of please take the time to read
this guide in full before you start. We’ve taken the time to highlight any potential
Thermogroup UK (TGUK) 15 Year Warranty applies:
pitfalls and common errors so you can avoid them and get the job done!
1. Only if the product is registered, and that the registration information is received
This product is covered by a 15 Year Warranty, subject to terms and conditions. Be
and documented by Thermogroup UK, within 60 Days after purchase. You can
sure to keep your receipt as proof of purchase, this will be required to validate your
register your product by completing the form online at www.thermogroupuk.com.
5 Year Warranty.
Proof of purchase must be presented to make a claim, so please ensure that you
keep a copy of both your invoice and purchase receipt in a safe place. Such invoice/
Please complete the Customer Handover section on page 11 in full so that your
receipt should clearly state the model that has been purchased and be in legible
customer has all the information they need to complete the online warranty form
condition so as to aid in identifying the system; and
and register their Thermofoil PRO Heating Mat 15 year Warranty.
2. Only if the Thermofoil PRO Heating Mat has been properly earthed and protected
by a Residual Current Device (RCD) at all times.
If you have any questions about your Thermofoil PRO Heating Mat or any of our
other products call our technical Support team on the freephone number below. We
This guarantee does not cover any thermostats as these are covered by a separate 3
will do our best to find a solution and will always give that little bit extra…
year warranty from the date of purchase, except as provided below.
Thanks again for choosing Thermogroup UK products.
All Thermogroup UK warranties become void if the floor covering under which the
Thermofoil PRO Heating Mat is originally fitted is damaged, lifted, replaced, repaired
or covered with additional layers of flooring, after a 15 year period from purchase.
You do not get this 15 year period with any other manufacturer guarantee. The
Thermogroup UK 15 Year Warranty does not cover accidental damage, including but
not limited to damage caused by lifting, replacing, repairing the original covering
laid after installation.
The guarantee period starts on the date of purchase but the registration is only
confirmed only when a letter or email of confirmation is sent by Thermogroup UK.
Should it be required, Thermogroup UK will arrange for the Thermofoil PRO Heating
Mat to be repaired or (at the discretion of TGUK) have parts replaced free of charge.
The cost of repair will only cover the cost of replacement TGUK parts and/or repair
to damaged TGUK parts and products. Any damage to floor coverings or floors, costs
of re-laying or repairing floors or floor coverings are not covered by the Thermogroup
UK 15 Year Warranty.
Please Note: Full Terms and Conditions are available on request.
Email [email protected] to request your copy or give us a call.
WWW.
CONTACT US ONLINE
CONTACT US BY PHONE
CONTACT US BY MAIL
WWW.
Browse our full product range, watch videos,
download product literature and get a quote,
all on the Thermogroup UK website.
WWW.THERMOGROUPUK.COM
2
Got a question or query? Call our UK support
line free from your land line.
Open 07:30 – 16:30 Mon - Fri
0800 019 5899
WWW.
Need to find us or want to write a letter to say
hello? Feel free to contact us at Bridge House.
Thermogroup UK, Bridge House,
Hop Pocket Lane, Paddock Wood,
Kent. TN12 6DQ.
If you have any questions or queries regarding this product, or any other products or services
Call our technical helpline for free on 0800 019 5899
W.
TFPIG1
Contents
The Do’s and Don’ts
Warning:
Regulations and guidelines
4
Warning:
Do’s and don’ts
4
Stage 1:
Preparation and Planning
Preparation:
Test procedure
5
Preparation:
How to cut, turn and position Thermofoil PRO mats
5
Planning:
Layout and calculations
6
Planning:
Floor finish option
7
Stage 2:
WWW.
64
-7
Warnings:
Installation
65-7
-7
68-10
-7
Step 1:
How to lay Thermofoil PRO mats
8
Step 2:
Lay laminate flooring & install thermostat
9
Step 3:
Carpet and vinyl floors - Heat Pak
Stage 3:
Testing & Customer Handover
Finalise:
Customer handover and trouble shooting
WWW. If you have any questions or queries regarding this product, or any other products or services
you can view our complete range online, WWW.THERMOGROUPUK.COM
10
6 11
-7
11
3
TFPIG1
! BEFORE YOU START !
ALL WIRING MUST CONFORM TO IEE 17TH EDITION PART P REGULATIONS
Thermofoil PRO™ is fully CE approved, certified and manufactured to the highest standards using state
of the art Fluropolymer coated cables. All our cables and mats are designed to be 17th Edition Part P
compliant and the instructions we supply with them include as much information as possible to ensure
that all installations comply with them. Please call our freephone customer care line if in any doubt on
0800 019 5899.
! IMPORTANT SAFETY REGULATIONS !
DO
DO NOT
CHECK WITH THE MANUFACTURER OF YOUR FLOORING, THAT
THEIR PRODUCTS ARE COMPATIBLE WITH ELECTRIC FLOOR
HEATING SYSTEMS
USE THE FOIL HEATING MATS WITH GLUED LOCKING SYSTEMS
OR LAMINATES THAT HAVE AN UNDERPAD OR CUSHION
MATERIAL PRE-ATTACHED TO THE UNDERSIDE
OPERATE THE HEATING MAT WITH A THERMOGROUP FLOOR
SENSOR THERMOSTAT TO ENSURE THE FLOOR DOES NOT
EXCEED THE MAXIMUM RECOMMENDED TEMPERATURE
(USUALLY 27°C)
INSTALL THE FOIL HEATER UP STEPS
ENSURE ALL EARTH LEADS ARE CONNECTED TO THE EARTH RING
CONNECT MULTIPLE COLD WIRE LEADS FROM THERMOFOIL
HEATING MATS IN PARALLEL, INSIDE AN ELECTRICAL JUNCTION
BOX
INSTALL OVER FLOORS THAT HAVE TRACES OF MOISTURE, ARE
UNEVEN OR OVER CARPETS OR PARQUET FLOOR
LEAVE INSULATING MATERIALS SUCH AS BEAN BAGS; LINEN OR
TOWELS ON THE FLOOR SURFACE
OVERLAP HEATING MATS, FOLD OR WRINKLE THE FOIL HEATING MATS
ZONE EACH HEATED ROOM WITH ITS OWN THERMOSTAT
CONTROLLER. THIS ALLOWS EACH ROOM TO BE CONTROLLED
INDIVIDUALLY SAVING YOU ENERGY BY ONLY HEATING THE ZONE
WHEN REQUIRED. EACH THERMOGROUP THERMOSTAT HAS A
MAXIMUM CAPACITY OF 16 AMPS
PLACE HEAVY/SHARP TOOLS (OR ANY OTHER POTENTIALLY
DAMAGING OBJECT) ON TOP OF THE HEATING MATS
ENSURE THAT NO SHARP EDGES (E.G. METAL-EDGED LAMINATE
LOCKING SYSTEMS) COME IN CONTACT WITH THE FOIL HEATING
INSTALL MATS WHEN THE ROOM TEMPERATURE IS BELOW -50C
INSTALL INSULATION / UNDERLAY BELOW THE HEATING MATS
TO PREVENT DAMAGE WHEN THE WEIGHT OF THE FLOOR
FURNITURE ETC IS ADDED. MAKE SURE UNAVOIDABLE WOODEN
FLOOR MOVEMENTS WILL NOT HARM THE FOIL MATS
INSTALL FOIL HEATING MATS ANYWHERE EXCEPT INSIDE BUILDINGS
ENSURE THAT A HEAT LOSS CALCULATION HAS BEEN CARRIED
OUT AND HEATING REQUIREMENTS HAVE BEEN MET IF YOU ARE
USING THE FOIL HEATING SYSTEM AS A PRIMARY SOURCE OF
HEATING
ENSURE THAT THE HEATERS ARE PROTECTED BY A SUITABLY
RATED RCD
ENSURE THAT THE CUSTOMER HANDOVER FORM (P11) IS
COMPLETED AND GIVEN TO THE CUSTOMER WITH ANY PLANS
AND TEST RESULTS IN ACCORDANCE WITH 17TH EDITION WIRING
REGULATIONS
USE THE FOIL TAPE PROVIDED TO BRIDGE ANY GAPS WHEN
CUTTING AND TURNING THE MATS. THIS IS IMPORTANT TO KEEP
THE EARTH INTACT
WALK UNNECESSARILY ON THE FOIL HEATING MATS
INSTALL FOIL MATS UNDER WALLS OR PARTITIONS, OR IN AREAS
UNDER HEAVY CABINETS, CLOSETS, OR FIXTURES (TOILETS,
SINKS, TUBS, ETC.)
INSTALL FOIL MATS WITHIN APPROXIMATELY 50MM OF ANY
HEAT CONDUCTIVE BUILDING PART, SUCH AS COLD WATER PIPES
INSTALL FOIL MATS WITHIN 20MM OF ONE ANOTHER, 50MM OF
ANY WALL OR 100MM OF A FIREPLACE OR HOT WATER PIPE
INSTALL FOIL HEATING MATS UNDER WOODEN FLOOR, IF THE
FLOOR IS THICKER THAN 18MM
PLACE ITEMS ON THE FLOOR SURFACE WHICH WILL STOP THE
AIR FLOW OR NOT ALLOW HEAT TO RISE INTO THE ROOM
INSTALL ELECTRICAL CABLES OR PIPES UNDER THE FLOOR WITH
THE FOIL HEATING MATS
FAILURE TO FOLLOW THESE INSTRUCTIONS WILL INVALIDATE THE WARRANTY. PLEASE TAKE CARE TO READ THIS GUIDE THOROUGHLY
Earth
UP
Earth
Earth
Plan your
installation
4
Position the
Conduit in the
correct area
Follow full test
procedure
Protect with an
RCD
Do not cut the
cable!
Do not leave
loose cable
exposed
Do not touch
electrics unless
fully qualified
Do not cross
Thermofoil
PRO cable
7
6
5
4
3
2
1
W.
TFPIG1
Planning: Performing a resistance test
Three test symbols
Be sure to check the electrical
resistance reading on the cable
three times; before, during and
after the installation process.
These test symbols throughout
this guide are a reminder:
A
B
C
Perform Test A
now and record
A the results on p11
Resistance test
Test Live and Neutral, conducting the
test in this way ensures total accuracy.
Record results
Write each resistance value on the
customer handover form (P11) to ensure
your customer can complete the warranty
form online.
B
Planning:
Thermofoil PRO™ cable formation options
Cable formation: Solutions for common and irregular areas
C below highlights some common cable formations to tackle irregular areas too small for a Thermofoil PRO mat. If you
The section
cannot see a solution to your installation here please call our customer help line (0800 019 5899).
A
Simple turns
Irregular areas
When you reach the end of a run, a simple turn can be achieved
by cutting across the silverfoil (not the cable!) with scissors or
a sharp blade. Turn the mat 180O and roll it out parallel to the
first run.
Thermofoil PRO will not always fit the spaces around irregular
shapes like a bath, toilet or sink pedestal.
B
C
1
Cut the silver foil, never cut the cable!
2
Turn through 180O
3
Continue rolling out cable side down (where possible)
More simple turns....
In this case simply remove the cable from the mesh and arrange
in loops to cover the area. Use a minimum cable spacing of
50mm and fix in place using the provided aluminium tape.
Do not place directly under permanent fixtures or furniture such
as under pedistals or vanity units.
Solutions for irregular areas...
! DO NOT CUT THE CABLE !
! DO NOT CUT THE CABLE !
! IMPORTANT SAFETY PRECAUTIONS !
Planning checklist:
TEST CIRCUIT RESISTANCE & RECORD RESULTS - TEST A
!
DO NOT CUT THE HEATING CABLE
!
IT IS VITAL TO APPLY ALUMINIUM FIXING TAPE TO ALL LOOSE
HEATING CABLES, T FOR HEAT DISTRIBUTION
TURN MAT USING SIMPLE GUIDE
FIX LOOSE CABLE USING TAPE PROVIDED
WWW.
5
TFPIG1
Planning: Layout
Items to plan for:
• Thermofoil PRO
• Thermostat
• Sensor and Conduit
• Heak Pak (If required)
Planning: Layout
Use the grid above to plan your installation. This will help you
to produce the safest, quickest and cleanest result with as little
wastage as possible.
Measure your room, if you don’t already know the dimensions,
and make a note of the available floor space excluding any
obstacles or fixtures you might have such as sanitary ware,
furniture or drainage. Use the grid to plan your installation
layout making sure to include thermostat and sensor positions.
Load calculations: Use the calculation below to work out the
overall current draw for your Thermofoil PRO system. If this
value is over 16A you will need to have a contactor/snubber
installed by a Part P qualified electrician. Call our technical help
line if you have any questions (0800 019 5899).
Example calculation:
Total Mat Wattage ÷ 230V = Amps (A)
Correct spacing is essential for an efficient system. Ensure
Thermofoil PRO is spaced evenly with at least 50mm gap
around the perimeter of the installation.
If your floor finish manufacturer requires, you will need to allow
for an edge insulation foam strip. Ask manufacturer if unsure.
Planning checklist
6
CALCULATE AVAILABLE FLOOR SPACE
!
SENSOR & CONDUIT MUST BE POSITIONED INBETWEEN 2
RUNS OF HEATING CABLE
SKETCH PLAN INCLUDING ALL REQUIRED PRODUCTS
!
DO NOT POSITION SENSOR & CONDUIT NEAR WATER PIPES OR
TEMPERATURE INFLUENCE
CONTACTOR/ SNUBBER IN PLACE IF REQUIRED
!
THE ELECTRICAL SUPPLY MUST ALWAYS BE PROTECTED BY AN
RCD. ENSURE THIS IS CATERED FOR BEFORE INSTALLATION
W.
TFPIG1
Planning: Substrate & Insulation Options
1
1
2
2
3
3
OR
4
5
4
5
!
1 Laminate Flooring
3 Thermofoil PRO
2 Vapour Barrier
4 Rigid Insulation
!
5 Concrete Substrate
1 Laminate Flooring
3 Thermofoil PRO
2 Vapour Barrier
4 Rigid Insulation
5 Timber Substrate
Option 1: Concrete Substrate
Option 2: Timber Substrate
The Thermofoil mat must not be installed in direct contact with
a cement or concrete slab. The heater must be installed on top
of a suitable rigid insulation board.
The Thermofoil mat must not be installed in direct contact with
timber floor boards or chip board flooring. The heater must be
installed on top of a suitable rigid insulation board.
Econoboard Insulation board may be used if additional levels
of insulation are required but a soft underlay will need to be
installed on top of the board.
Econoboard Insulation board may be used if additional levels
of insulation are required but a soft underlay will need to be
installed on top of the board.
A vapour barrier should be installed between the Thermofoil
PRO mat and floor finish. This helps to eliminate any possible
damage that could be caused by movement in the floating floor.
A vapour barrier should be installed between the Thermofoil
PRO mat and floor finish. This helps to eliminate any possible
damage that could be caused by movement in the floating floor.
Carpet or vinyl floor finish? See page 10 for details.
Checklist:
WWW.
FULLY UNDERSTAND THE DIFFERENCE BETWEEN THERMOFOIL
APPLICATIONS ON TIMBER AND CONCRETE SUBSTRATES
!
PLEASE READ MANUFACTURERS SPECIFICATIONS OF
FLOORING PRODUCTS USED IN CONJUNCTION WITH
THERMOFOIL PRO
ENSURE DESIRED FLOOR FINISH IS COMPATIBLE WITH
UNDERFLOOR HEATING
!
ENSURE HEAT PAK IS INSTALLED AT LEAST 24 HOURS BEFORE
VINYL GLUE IS USED
7
TFPIG1
Installation: Lay Thermofoil PRO mats
1
2
3
A
1
2
B
Step 1: Roll out the mat
Step 2: Simply cut and turn the mat
Make sure your substrate and insulation is clean and dust free
before installing your Thermofoil PRO heating mat.
When you reach the end of a run, a simple turn can be achieved
A
by cutting across the foil with scissors or a sharp blade, never
B
C
cut the heating cable. Turn the mat 180O and roll it out parallel
to the first run.
Lay Thermofoil PRO wire side up where possible. Place the
Thermofoil PRO in the starting position, and roll it out ensuring
the conduit position lines up in between two runs of heating
cable as planned.
Feed the cold tail up and into the channel in the wall, through
the cavity or pre installed conduit.
If you have not already done so now is a good time to chase a
shallow channel out of the insulation or substrate to recess the
cold tail into the floor slightly. This will make fitting your floor
finish easier.
1
Cut the foil, never cut the cable!
2
Turn through 180O
3
Continue rolling out the mat cable side down
C
For more information on mat turns see page 5.
Tape down exposed heating cable and join mats
All exposed cable must
be covered and cut mats
must be joined for earth
continuity and safety.
Tape over all exposed cable
and join any cut mats together
using the provided aluminium
fixing tape. Run an earth
continuity test if unsure.
PRO TIP
Allow a gap of between 50 - 100mm from the wall to the edge
of the Thermofoil PRO mat.
A
Perform Test B
now and record
B the results on p11
Step 1 & 2 checklist:
C
LAY THERMOFOIL PRO WIRE SIDE UP WHERE POSSIBLE
B
FEED COLD TAIL UP WALL TO BACK BOX
8
COVER ALL EXPOSED HEATING CABLE AND JOIN ANY CUT
MATS WITH ALUMINIUM TAPE TO ENSURE EARTH CONTINUITY
!
A
LEAVE GAP OF 50-100MM BETWEEN MAT & WALL
!
C
IF USING HEAT PAK DO NOT INSTALL SENSOR PROBE AT THIS
POINT. IT MUST BE INSTALLED WITHIN THE HEAT PAK LAYER
W.
TFPIG1
Installation: Lay flooring and connect thermostat
A
B
3
4
C
A
Step 3: Lay laminate flooring
Step 4: Thermostat installation
You can now lay a vapour barrier and then the final floor
covering. Please take care not to damage the mat in any way.
If you are not instantly laying your floor finish onto Thermofoil
PRO please cover with a protective material in the meantime.
Make electrical connections as show in your Thermostat
Installation Guide which comes in the Thermostat box.
B
Floating and laminate floors usually require an strip of
expansion foam around the edge of the room. Check your floor
finish manufacturer guidelines for more information.
C
The image above shows the correct wiring configuration for:
5259 Touchscreen Programmable Thermostat
5255 Chrome Touchscreen Programmable Thermostat
5257 Satin Black Touchscreen Programmable Thermostat
Your thermostat may require a different wiring diagram.
Please consult the relevant installation guide for full details.
A
B
Perform Test C
now and record
C the results on p11
WIRE THERMOSTAT TO AN RCD
CONNECT WIRING IN ACCORDANCE WITH RELEVANT
WIRING DIAGRAM
INSTALL THERMOSTAT SECURELY TO BACK BOX AND EARTH
WWW.
A
! IMPORTANT SAFETY PRECAUTIONS
!
B
ISOLATE ELECTRICS BEFORE DOING ANY ELECTRICAL WORKS
!
DO NOT LAY LAMINATE DIRECTLY ONTO THERMOFOIL USE A
VAPOUR BARRIER LAYER
C
!
9
TFPIG1
Installation: Carpet or vinyl flooring - Heat Pak
A
B
Step A: Heak Pak - Carpet and vinyl floors
Step B: Heat Pak continued & floor finish
If you are installing carpet, vinyl or another non-laminate
flooring you will need Heak Pak. You will need a vapour barrier
(200 microns) between Thermofoil and Heat Pak.
It is important to check that any trimming of the top board
is accurate and that the adhesive coating is free from dust
or fragments before removing the protective film from the
baseboards. The adhesive will allow minor adjustments to be
made for accurate positioning until pressure is applied.
The Heat Pak system consists of two self-adhesive boards,
baseboards and top boards, which bond to each other. Heat
Pak is a floating sub-floor. It is not fixed to the floor below. Each
layer is laid out with staggered joints and arranged so that the
top boards overlap the joints in the baseboards. Baseboards
are thinner and have a protective plastic film to keep the selfadhesive coating clean. This is laid facing upwards and the film
is left in place until cutting and fitting is completed.
The top boards are thicker and have no plastic film over the
adhesive coating. They are carefully positioned, adhesive side
down, so that they overlap all the baseboard joints.
Expansion gap
9
Wall
Skriting
Floor finish
Top board
Base board
Vapour barrier
Thermofoil PRO
Rigid insulation board
Substrate
10
8-10mm Expansion Gap
1
2
3
4
5
6
7
8
2
3
4
5
6
7 8
10
9
1
Tapping down with a rubber mallet will ensure close contact of
the adhesive coatings and produce a strong, permanent bond.
Take care to position boards accurately as it is very difficult
to separate them once bonded. The heating system must be
switched off before installing Heat Pak. If the floor finish is to be
glued to the Heat Pak , the system must not be switched back
on until the glue has set completely. Temperatures should then
be increased gradually.
Special attention should be made to the location of the floor
sensor. A 5mm wide groove should be formed in the top board
layer of the Heat Pak to take the tip of the sensor and allow the
cable to run to the 50mm gap at the edge of the room. If the
final floor finish is to be vinyl or similar the groove/sensor and
joins should be covered with flexible filler.
Floor finish
You are now ready to apply your floor adhesive (if necessary)
and floor finish. Please ensure you wait at least 24 hours before
applying any adhesives to Heat Pak.
VAPOUR BARRIER LAID BETWEEN HEAT MAT AND FLOOR
APPLICATION
!
ALLOW 8-10MM EXPANSION GAP UNDER SKIRTING
!
DO NOT LAY CARPET OR VINYL DIRECTLY ONTO THERMOFOIL
USE A HEAT PAK LAYER IN BETWEEN
LAY BASE BOARD
LAY THICKER TOP BOARD WITH STAGGERED JOINS
10
W.
TFPIG1
Finalise: Customer handover
This is the place to record the resistance test results which should be carried out when prompted
during the installation process. Please fill out the entire form in clear writing to ensure your customer
can register their system online or contact you with any queries that may arise after installation.
Thermofoil PRO
Installation Guarantee
THERMOFOIL PRO ON SITE RESISTANCE TEST RESULTS
0
ROOM
REFERENCE
STOCK
NUMBER
Example Room
121402
MAT
AREA (M2)
1.0
CONDUCTOR / CONDUCTOR
CONNECTION
WIRE
EXTENSION
15.7
YES / NO
1
YES / NO
2
YES / NO
3
YES / NO
4
YES / NO
5
YES / NO
6
YES / NO
7
YES / NO
8
YES / NO
9
YES / NO
10
YES / NO
KEY: Test A: After laying the Thermofoil PRO mat
A
B
15.3
CONDUCTOR / EARTHBRAID
C
15.9
A
0c
B
0c
C
0c
Test B: During floor finishing Test C: On completion of floor finishing
The Thermofoil PRO™ Under laminate Heating 15 year guarantee against manufacturers defects is a limited liability warranty and will only apply if the
product is registered online. Online warranty registration must be completed within 60 days of installation to apply. Your statutory rights are not affected. In
the event of a problem with your installation contact your Thermofoil PRO™ stockist. Alternatively telephone the Thermogroup advice line 0800 019 5899.
Take photographs of installation at all stages of installation.
Fill out and sign the boxes below to declare that all the information recorded on this form correlates to the installation.
CUSTOMER
INSTALLER
Name:
Name:
Email:
Email:
Website:
Website:
Address:
Address:
Postcode:
Part P number:
Postcode:
Telephone:
Telephone:
Signature:
Signature:
Customer handover checklist:
COMPLETED ALL 3 TESTS & RECORD RESULTS
TAKEN PHOTOGRAPHS AT ALL STAGES OF INSTALLATION
!
ENSURE YOU COMPLETE ALL 3 RESISTANCE TESTS AND
ACCURATELY RECORD THE RESULTS ON THIS PAGE
!
FAILURE TO COMPLETE THIS FORM IN FULL WILL INVALIDATE
THE WARRANTY
GIVEN CUSTOMER A COPY OF ORIGINAL PROOF OF PURCHASE
COMPLETED AND SIGNED CUSTOMER HANDOVER FORM
GIVEN CUSTOMER A COMPLETED COPY OF THIS FORM
WWW.
11
TFPIG1
Thermofoil PRO
Stock No.
Size (m)
Output (A)
Voltage (V)
Resistance (Ω)
Area(m2)
121402
2.0lm x 0.5m
140
230
377.9
1.00
121403
3.0lm x 0.5m
210
230
251.9
1.50
121404
4.0lm x 0.5m
280
230
188.9
2.00
121405
5.0lm x 0.5m
350
230
151.1
2.50
121406
6.0lm x 0.5m
420
230
126.0
3.00
121408
8.0lm x 0.5m
560
230
94.5
4.00
121410
10.0lm x 0.5m
700
230
75.6
5.00
121412
12.0lm x 0.5m
840
230
63.0
6.00
121416
16.0lm x 0.5m
1120
230
47.2
8.00
121420
20.0lm x 0.5m
1400
230
37.8
10.00
121424
24.0lm x 0.5m
1680
230
31.5
12.00
WWW.
CONTACT US ONLINE
CONTACT US BY PHONE
CONTACT US BY MAIL
TFPIG_A4_201113.PDF
WWW.
Browse our full product range, watch videos,
download product literature and get a quote,
all on the Thermogroup UK website.
WWW.THERMOGROUPUK.COM
Got a question or query? Call our UK support
line free from your land line.
Open 07:30 – 16:30 Mon - Fri
0800 019 5899
WWW.
Need to find us or want to write a letter to say
hello? Feel free to contact us at Bridge House.
Thermogroup UK, Bridge House,
Hop Pocket Lane, Paddock Wood,
Kent. TN12 6DQ.
Thermogroup UK
Bridge House
Hop Pocket Lane
Paddock Wood
Kent
TN12 6DQ
0800 019 5899
[email protected]
www.thermogroupuk.com
E&OE © Thermogroup UK 2012

Thermofoil PRO

Transcription

Similar documents

Thermofoil - Thermogroup UK

Equipment List Brochure PDF - Integrated Wood Components

Atlantis Energy Systems Inc.

thermofoil finishes

Regions CD Check Viewer Installation Guide

DOLLAMUR SPORt SURFACES PROUd tO bE thE OFFICIAL MAt

WHY THE YAKTRAX PRO WORKS

SCAG 12.cdr

QuadraTec™ - Auralex Acoustics

Products_files/6 (catalogo DECO PROJECTS.EN)

Warranty Info