technical changes possible

Transcription

www.winys-archery.com
Precision made in Germany
Product Overview
Winfried Schröppel
Friedrichstr. 133
DE-72800 Eningen u.A.
[email protected]
Tel.: +49 7121 88587
technical changes possible pictures may differ slightly to
the original parts. Shaft compatibility data without guarantee
date: 15.02.2016
About Winys Archery
Winfried Schröppel himself is a traditional and field archer since years
and nationwide successfull (German Champion 2013)
Over the years and with increasing score he was looking himself for
arrow points with much higher precision, easier to pull, much more
robust ballistic curve, tighter weight tolerance and much later slipping
of the edge of 3D-animals. This was the hour of birth of Winys
Archery. After developing of an own design and several improvements
the scope of supply increased steadily.
But the philosophy: “Your Problem is our Challange” never changes.
We still engineer and produce tailor-made solutions for high end
shooters and dealers.
Have fun and success with our products.
We are always very grateful over every feedback you may have.
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
Philosophy of the
point design:
Soft Cone Angle
reduces tendency
of welding together
with target material
Interface Diameter
accurately fitting for minimal
resistance in the target for
pullung the arrow
Slim Point
- reduces slipping of
- protects shaft against
hard impact (collapsible
zone)
Soft Cone Angle
reduces tendency
of welding together
with target material
Max. Diameter
protects following,
smaller shaft
Interface Diameter
accurately fitting for minimal
resistance in the target for
pullung the arrow
Slim Point
Max. Diameter
- reduces slipping of
protects following,
- protects shaft against
smaller shaft
hard impact (collapsible
zone)
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
O-Ring-Tech
prevents loosening
of the thread
Breakoffs
- easy to break
- tight weight tol.
long adherend
- best centering and connection
- scales vary glueing gap always
to optimum
Content:
Screw-in Points
Glue in Points
Points for:
Victory, Aurel, Easton, Goldtip
Easton A/C/E
Easton ACC
Easton X10
Carbon Express
Carbon Impact / Bearpaw
Fivics Mach3
balancing weight for bare bows
special hot melt glue
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
Page 1/2
Sure-Fire threaded Point
- robust balistic curve
- reliable score by low slipping tendency at
the edge of 3D-Targets
- collapsible zone protects shaft against severe impact
- Line-Breaking-Effect and shaft protection by IFAA-conform
oversize max. diameter
- easy pulling by reduced tendency to weld with target mat.
- tight weight tolerances
- O-Ring-Technology prevents loosening of the thread
- useable for all standard threaded inserts (RPS)
Properties:
9/32
19/64
5/16
21/64
11/32
23/64
30grain
60grain
80grain
100grain
125grain
145grain
190grain
Manufactured out of steel
High performance Aluminum
optional available in hardened carbon steel
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
NEW
Page 2/2
Sure-Fire Schraubspitze
Partnumbers:
9/32
19/64
5/16
21/64
11/32
23/64
30grain
SF9-32-O-30
SF5-16-O-30
60grain
SF9-32-O-60
SF5-16-O-60
80grain
SF9-32-O-80
SF19-64-O-80
SF5-16-O-80
SF21-64-O-80
SF11-32-O-80
100grain
SF9-32-O-100
SF19-64-O-100
SF5-16-O-100
SF21-64-O-100
SF11-32-O-100
SF23-64-O-100
125grain
SF9-32-O-125
SF19-64-O-125
SF5-16-O-125
SF21-64-O-125
SF11-32-O-125
SF23-64-O-125
145grain
SF9-32-O-145
SF5-16-O-145
SF21-64-O-145
SF11-32-O-145
SF5-16-O-190
SF21-64-O-190
190grain
SF23-64-O-190
NEW
Parts marked with the red triangle are optionally available as “Heavy-Duty”-version
manufactured out of hardened carbon stee! This material is almost 5 times harder
than conventionally used materials like steel or stainless.
Please add the suffix “HD” to the part number.
(SF5-16-O-80 e.g. would become SF5-16-O-80HD.
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
Historical threaded Point
(Bodkin)
Properties:
Weight:
Size:
Partnumber:
Remark:
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
- all edges rounded => no cutting of the target
- O-Ring-Technology prevents loosening of the thread
- made out of hardened carbon steel
- useable for all standard threaded inserts (RPS)
~130Grain
Made for connector OD 5/16” = 7,9mm
SF5-16-O-130hist
The point is designed for all usual target materials
Before shooting please make sure with the concerned
supervisors and owners that they agree using this points
Page 1/2
Sure-Fire Glue-in Points
Properties:
- long glueing area guarantees reliable conection to the
shaft and supports critical erea of the shaft right
behind the point
- outstanding concentric runout
Fitting into:
Easton
2
- Eclipse, Blues, Jazz, X 3, X7, XX75, Tribute, Platinum,
Magnum, HEXX
Carbon Express
- CXL Pro, X-Buster
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
Page 2/2
Sure-Fire Glue-in Points
For
1214
Picture
45 Grain
Partnumber
KSF 1214
1413
40 Grain
KSF 1413
1416
50 Grain
KSF 1416
1516
50 Grain
KSF 1516
1616
60 Grain
KSF 1616
1716
70 Grain
KSF 1716
1816
70 Grain
KSF 1816
1916
80 Grain
KSF 1916
80 Grain 100 Grain 125 Grain 145 Grain 190 Grain
2314
KSF 2314 …
… 145 … 190
2315
KSF 2315 …
… 145 … 190
KSF XB600 …
… 145 … 190
CXL-Pro150
X-Buster 350-500
KSF CXL …
X-Buster 600-700
KSF XB600 ...
HEXX
80-120 Grain
KSF-HEXX
Example:
Point for Platinum 1816 = KSF 1816
Point for CXL-Pro150 with 145Grain = KSF XB600 145
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
… 80 … 100 … 125
… 145 … 190
… 145 … 190
B r e a k o f f
High performance aluminum
Stainless steel
Page 1/4
Sure-Fire Breakoff Point
Properties:
oversize max. Diameter
- easy pulling and line breaking effect by oversize max. OD
- long glueing area guarantees reliable connection to the
behind the insert
- easy weight adjustment by 5 breakoffs with 10 Grain each
Fitting into:
- Victory VAP
- Easton A/C/E, Carbon One, A/C Pro Field, A/C/G, Apollo
Lightspeed, Flatline, Powerflight
- Aurel Agil, Uhyre, Oryx, Mako
- Goldtip Traditional, Falkon, Twister, Velocity,
Hunter, Ultralight
- Fivics Mach3
Remark:
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
- for Carbon Express Maxima, please go to page
CE Maxima
Page 2/4
For
Victory VAP 350-500(1000)
Pictures
Grain Partnumber
70-120 SF-VIC NANO F350
70-120 SF-VIC NANO F350HD
Victory VAP 600-1000
Victory VAP 600-1000
70-80
SF-VIC NANO F600-80
AUREL Uhyre 400-500
70-120 SF-AU-MOU 120
AUREL Uhyre 500-800
AUREL Uhyre 500-800
70-80
SF-VIC NANO F600-80
Aurel Oryx, Mako - 350-500
70-120 SF-AU-MOU 120
70-80
SF-VIC NANO F600-80
Aurel Agil
70-120 SF-AU-AGIL 120
Goldtip Ultralight, Pro, Entrada
70-120 SF-AU-AGIL 120
Goldtip Falkon, Twister
70-120 SF-AU-AGIL 120
Goldtip Hunter ab 400
70-120 SF-AU-AGIL 120
Goldtip Velocity ab 340
70-120 SF-AU-AGIL 120
Goldtip Traditional ab 400
70-120 SF-AU-AGIL 120
Manufactured out of stainless steel
hardened steel
high performance aluminum
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
Page 3/4
For
Easton A/C/E, A/C Pro Field
Pictures
Grain Partnumber
70-120 SF-BT-A-70/120
Easton A/C/G, Apollo
70-120 SF-BT-A-70/120
Easton Carbon One 900-1150
70-120 SF-BT-A-70/120
70-120 SF-BT-CO-70/120
70-120 SF-VIC NANO F350HD
Easton Carbon One 410
70-120 SF-AU-MOU 120
Easton Lightspeed
70-120 SF-AU-AGIL 120
Easton Flatline
70-120 SF-AU-AGIL 120
Easton Powerflight
70-120 SF-AU-AGIL 120
SkyArt Axiom 400-600
SkyArt Axiom 600-1300
SkyArt Stone Crusher 400-600
SkyArt Stone Crusher 600-700
Fivics Mach3
Fivics Mach3 ab 800
hardened steel
high performance aluminum
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
Page 4/4
adapted to Strawtargets
For
Pictures
Grain Partnumber
90-120 SF-VIC NANO F350HD STR
AUREL Oryx, Mako 600-1300
AUREL Uhyre 500-800
Easton A/C/E, A/C/G, Apollo
80-130 SF-BT-A-130STR
80-130 SF-BT-A-130STR
Hardened carbon steel
Properties:
Specifically designed for targets out of compressed straw
- much easier pulling
- reduces straw sticking to the shaft
- soft slow down of the arrow
- hardened steel prevents deformation of the point to a
5 times higher extend!!
Fitting into:
Victory VAP350-500(1000)
Easton:
- Carbon One 600-900(1150)
- A/C/E, A/C Pro Field, A/C/G, Apollo
Aurel:
- Uhyre, Oryx, Mako
(Nevertheless, straw is a very challanging target material.
The points are designed to cope as best as possible with
this hard material. An arrow is stopped from up to 300fps
within 2 inches!!!
This results in a very high stress by bending and wear)
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
Page 1/2
A/C/E-Points and Insert
Properties:
- easy arrow tuning by using the 4 available point weights
together with the outstanding Breakoff-Insert with
10 breakoffs with 5 grain each
- quick point change for 3D and Field archers
- cone effect secures point from loosening and provides
outstanding concentricitiy
behind the insert
- outstanding concentric runout of insert and point by
double centering fit
Fitting into:
- Easton:
A/C/E, ACC 00, Carbon One 600-900/900-1150,
A/C Pro Field, A/C/G, Apollo
- McKinney II
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
Page 2/2
A/C/E-points and Insert
For
A/C/E & Carbon One
A/C/E & Carbon One 900-1050
Carbon One 600-900
A/C/E & Carbon One 600-900
Picture
Grain Part Numbers
20
BT-A-20 auf Anfrage
30
BT-A-30
40
BT-A-40
50
BT-A-50
20-70
Insert A 10x5
70-120 SF-BT-A-70/120
20-70
Insert CO AB 10x5
Stainless steel
Brass zinc coated
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
Page 1 / 2
ACC-Spitzen mit Insert
Properties:
- very simple arrow tuning by quick interchangeable
point with 3 available weights together with a
break off insert for raw adjustment
- quick interchange of points for field archers
- O-Ring-Technology against loosening of the thread
- Line-Breaking-effect and shaft protection by slightly
oversize max diameter
- easier pulling and reduced tendency to welding
- long glueing area guarantees outstanding connection
to the shaft and stabilizes front end of the shaft
- extremely tight weight tolerances
- outstanding concentric run-out
Fitting into:
- Easton: ACC 04 und ACC 18
- Carbon Express:
Predator 700 and softer (ACC 18)
Medaillon XR (ACC 04)
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
Page 2 / 2
ACC-Points with Insert
For
ACC04 & ACC18
Picture
Grain Partnumber
45
BT-O-45
ACC04 & ACC18
55
BT-O-55
ACC04 & ACC18
65
BT-O-65
ACC04
15-55
Insert 8/32-470AB
ACC04
5
Insert 8/32-470
ACC18
20-60
Insert 8/32-510AB
ACC18
7
Insert 8/32-510
Made out of Stainless Steel
High Performance Aluminum
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
Sure-Fire X10 Glue-in Point
Properties:
Weight:
Dimension:
Partnumber:
Remark:
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
- robust balistic curve with low resistance profile
- very enduring and no distortion - made out of
hardened carbon steel
- outstanding weight tolerance and concentric runout
70-120 Grain
Designed for Easton X10 / X10 Pro-Tour
SF-X10-HD
Found superior to standard points by high end and
staff shooters!!
Page 1/2
Glue in Point for CE Maxima
Properties:
- cone effect secures weight from loosening and provides
outstanding concentricitiy
behind the insert
- outstanding concentric runout of point and weight by
double centering fit
- provides an outstanding weight range of 30 up to 120gn
Fitting into:
- Carbon Express:
Maxima Hunter
Maxima Red
Maxima Blue Streak Select
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
Page 2/2
Glue in Point for CE Maxima
For
Picture
Grain Part Numbers
Maxima Glue in Point
30
SF CE MX30
Maxima Glue in Point
70
SF CE MX70
10-50
SF CE W 5x10
selfcentering Breakoff-Weight
Manufactured out of
Stainless steel
High performance aluminum
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
Page 1/2
KUF Glue-in Points
Properties:
- long glueing area guarantees reliable conection to the
behind the point
- reliable score with 3D-animals - no sliding off
- simple weight adjustment by break off
Fitting into:
- Carbon Impact Ultra Fast, Super Club
- Bearpaw Penthalon
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
Page 2/2
KUF Glue-in Points
For
CI Ultra Fast 500-710
CI Super Club 3040/4050
Pictures
Grain
Productnumber
70-120 KUF500-710/120
BP Penthalon 300-600
CI Super Club 1020/1525/2030
50-90
KUF820-950SF
50-90
KUF950-1200SF
CI Super Club 1020/1525
out of stainless steel
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
Page 1/2
Balancing Weights for Bare Bows
Properties:
Weight:
- Connecting thread 5/16”UNF - fitting into Stabibushing
- prevents bouncing of the bow after shot
- calms the bow significantly
- reduces impact on the wrist
- also usable for training mounted on limb bolts
(straightens the bow and gives extra weight)
- IFAA compatible (12,2cm-Ring) with most risers
300, 400, 500, 600, 700 gram
Partnumbers:
GZ300
GZ400
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
GZ500
GZ600
GZ700
Page 2/2
Balancing Weights for Bare Bows black
Properties:
- Connecting thread 5/16”UNF - fitting into Stabibushing
- prevents bouncing of the bow after shot
- calms the bow significantly
- reduces impact on the wrist
- also usable for training mounted on limb bolts
(straightens the bow and gives extra weight)
- IFAA compatible (12,2cm-Ring) with most risers
300, 400, 500 gram
Weight:
GZ300S
GZ500S
Partnumbers:
GZ400S
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
Präzision made in Germany
Seite 1/1
Special
hot-meld adhesive
for carbon arrows
Properties:
Winfried Schröppel
Friedrichstr. 133
[email protected]
Tel.: +49 7121 88587
- extremly low melting point for maximum protection
of the resin in the shaft material
- extraordinary high adhesive forces
- optimised viscosity to bridge the gap between shaft and
point material
- remains ductile even with very low temperature
- easy to handle and process
- easy disassemling for replacement or repair
- bar approx. 11x200mm
- Colour: nature white
technische Änderungen
vorbehalten - Abweichungen
zu den Abbildungen sind
möglich. Angaben zu kompatiblen Schäften ohne Gewähr

technical changes possible

Transcription

Similar documents

GRAIN CART 30TN ASCANELLI.cdr

VIBCO REPAIR KIT INSTRUCTIONS for BBS

Clubmaker`s Belt Sander

HT-HTM Mixers_NOV.qxd

Zero Turn Hydrostatic Transaxle

SYC-300M - Leadermac USA

tools needed start - Global Industrial

Lil` Indian_NEW

SIMPLAN Shaft Seals for Water Lubricated Sterntubes

EASTON Archery Guide 00/01