Product Catalog

The
Crowning Touch
Decorative &
Plain Cornices
Friezes
Panel
Mouldings
Accessories
Decorative
Corners
ts
Decorative
Drops
e
ck
ra
B
air
St
Decorative
Panel
Mouldings
Door/Window
Casings
Decorative
Medallions
Recessed
& Surface
Mounted
Niches
Value and Design come together to create a line of millwork designed
to give all your projects a distinctive finish...a designers finish
Suggested
Installation
Mouldings may be installed much the same way you would install wood mouldings. For a better fit, it is advised that a flat or “Butt Joint” is used to
join longer lengths of polyurethane mouldings. Cut all pieces 1/8th of an inch longer than the required measurement, fitting the ends in place first and
the middle sections last. Always place a continuous bead of premium polyurethane adhesive along all adjoining wall and ceiling surfaces before final
positioning of the moulding. Poly-glue is essential when attaching one length of moulding to the next. A pneumatic pin nailer works well for fastening
mouldings to wall and ceiling surfaces; alternatively, trim head drywall screws or finishing nails may be used.
RPS Note: • High Impact
• When cutting RPS mouldings, use a thin panel saw, recommended 10” blade, 80 or 120 teeth with face up and quick strokes.
Filling and Sanding
Once all of the mouldings are fixed in place, fill any joints or remaining
voids with a paintable siliconized latex caulking. This same caulking may
be applied sparingly along the top and bottom edges of the moulding
where it meets the ceiling and wall. A damp cloth or silicone coving
tool may be used to clear away any excess caulking to leave a clean
professional look.
Any remaining nail or screw holes may be filled with sandable, paintable
non-shrinking filler. Be careful not to over sand the surfaces of your
mouldings. Sanding past the protective barrier undercoating may
necessitate further filling and sanding to maintain a paintable surface.
Ceiling Medallions
Place a solid bead of premium adhesive around and about the backside
of the medallion. Pressing the medallion into place, it may then be
secured with 4 trim head dry wall screws. Be sure to place the screws
so that any holes created may be filled and sanded with minimal effort.
Finishing
2
Before installing moulding, lightly sand and wipe material to avoid any dirt
and impurities. This is important to obtain good adhesion and a smooth
finish. Comes primed white and ready to finish with a good quality oil or
latex based paint.
Polyurethane DEM Mouldings
DEM Mouldings and Millwork encompass a full decorative array of premium
quality polyurethane cornice and panel mouldings, medallions, niches, stair
brackets, pilasters and other ornamental products that are guaranteed
to satisfy all decorative requirements without compromise. DEM is
impervious to adverse climate and weather conditions, and, because of
its dimensional stability, will not alter over time. Produced in exclusive
molds that yield ornate and sharply defined details, perfect dimensions,
and extremely consistent quality, DEM is lightweight, impact resistant
and easy to install and finish using traditional woodworking techniques
and tools.
ADH1 10.6 oz tube
PL Premium Adhesive
Approximate adhesive yields *
Mouldings 2” + Under – 60’
Mouldings 2 - 5” – 45’
Mouldings 5” + Over – 30’
* Y ields are approximate and based on
average conditions and installation technique.
Polystyrene High Density RPS Mouldings
RPS 100% Recycled High Density Mouldings, which are impervious to
adverse climate and weather conditions, offer an economical decorative
and design medium that are manufactured from renewable polystyrene
resources. Introduced as a cost effective alternative to more costly
polymer mouldings and millwork, RPS Mouldings will aesthetically
satisfy all decorative requirements without having to compromise for
lesser quality mouldings. The polystyrene compound from which RPS
Mouldings are manufactured, not only produces a durable, impact
resistant surface, making them ideally suited for use in high traffic
areas, RPS Mouldings can be easily cut, nailed, glued, finished and
installed using the same woodworking techniques and tools as wood and
mdf mouldings & millwork.
The “Original” Hybrid Formula
MP-25-ADH is a high performance, one component, permanently flexible, easy
to use, multi-purpose fast cure modified polyurethane sealant. MP-25-ADH
cures rapidly when exposed to atmospheric moisture to form a durable bond.
• Use as adhesive or filler • Eco-friendly, low VOC’s
• Fast cure • Paintable • Non-yellowing
3
MP-25-ADH
Decorative Cornices
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
100% RECYCLED POLYSTYRENE
DEM-107
DEM-105
2”
1-1/4”
2”
94-1/2” Length
2-5/8”
2-7/8”
2-3/4”
94-1/2” Length
Design Repeat: 1/2”
Design Repeat: 2-1/2”
DEM-113
DEM-111
2-1/8”
2-1/8”
2-1/8”
2-3/8”
3”
94-1/4” Length
3-1/8”
Design Repeat: 1-7/8”
94-1/2” Length
Design Repeat: 3/8”
DEM-115
DEM-114
2”
2-5/8”
2-3/8”
94-1/2” Length
3-1/8”
3-5/8”
3-1/2”
Design Repeat: 3-15/16”
96” Length
DEM-120
Design Repeat: 1”
DEM-122
3”
3-1/8”
3”
2-3/4”
4-1/8”
94-1/2” Length
4-1/8”
Design Repeat: 3/4”
94-1/2” Length
CORNERS
INSIDE
DEM-120-A
Design Repeat: 1-1/2”
CORNERS
Pre-mitered corners
INSIDE
DEM-122-A
OUTSIDE
DEM-120-B
Pre-mitered corners
OUTSIDE
DEM-122-B
All dimensions are approximate. Cornice Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
4
Decorative Cornices
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
DEM-125
100% RECYCLED POLYSTYRENE
DEM-130
3-5/8”
3”
3-3/8”
3-1/8”
4-1/2”
96” Length
4-13/16”
Design Repeat: 1-15/16”
94-1/2” Length
Design Repeat: 4-1/2”
CORNERS
DEM-126
3-1/2”
3-1/8”
4-5/8”
94-1/2” Length
INSIDE
DEM-130-A
Design Repeat: 1”
OUTSIDE
DEM-130-B
Pre-mitered corners
DEM-132
DEM-131
2”
3-1/4”
4-3/4”
94-1/2” Length
3-1/2”
4-1/2”
5”
Design Repeat: 7” Corbel to Corbel
94-1/2” Length
Design Repeat: 31-1/2”
DEM-134
2-1/2”
5”
94-1/2” Length
4-1/2”
Design Repeat: 8”
All dimensions are approximate. Cornice Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
5
Decorative Cornices
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
100% RECYCLED POLYSTYRENE
DEM-142
DEM-136
3-7/8”
3-3/8”
3-3/8”
3-3/4”
5-1/8”
5”
94-1/2” Length
94-1/2” Length
Design Repeat: 1-1/2”
CORNERS
CORNERS
INSIDE
DEM-142-A
OUTSIDE
DEM-136-B
INSIDE
DEM-136-A
Design Repeat: 12”
OUTSIDE
DEM-142-B
Pre-mitered corners
DEM-147
Pre-mitered corners
4-3/4”
DEM-146
3-1/8”
4-1/2”
5-1/2”
94-1/2” Length
3-3/4”
6”
94-1/2” Length
Design Repeat: 3-1/2”
(Dot Repeat 3/8” wide x 3 dots per inch)
DEM-148
Design Repeat: 4-1/2”
3”
CORNERS
6”
OUTSIDE
DEM-146-B
INSIDE
DEM-146-A
Pre-mitered corners
94-1/2” Length
Design Repeat: 1-5/8”
DEM-149
4-1/8”
3-3/4”
5-1/2”
96” Length
Design Repeat: 6”
All dimensions are approximate. Cornice Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
6
5”
Decorative Cornices
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
DEM-150
100% RECYCLED POLYSTYRENE
DEM-151
4”
3-5/8”
96” Length
3-15/16”
4”
5-1/2”
5-3/8”
94-1/2” Length
Design Repeat: 1-5/8”
CORNERS
DEM-153
Design Repeat: 3-15/16”
3-15/16”
3-15/16”
5-5/8”
95-3/4” Length
INSIDE
DEM-151-A
OUTSIDE
DEM-151-B
Pre-mitered corners
Design Repeat: 5/8”
DEM-155
3-15/16”
4-1/2”
6”
96” Length
Design Repeat: 5-1/16”
DEM-156
2-3/8”
5-1/2”
6”
94-1/2” Length
Design Repeat: 6”
DEM-157
3-7/8”
4-5/8”
6”
96” Length
Design Repeat: 3-7/8”
All dimensions are approximate. Cornice Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
7
Decorative Cornices
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
DEM-158
100% RECYCLED POLYSTYRENE
DEM-159
2-1/2”
4-1/4”
5-7/8”
4-3/4”
6-7/16”
6-3/8”
94-1/2” Length
96” Length
Design Repeat: 3”
DEM-160
Design Repeat: 12”
DEM-161
4-3/8”
4-5/8”
5”
4-1/2”
6-1/2”
6-1/2”
94-1/2” Length
96” Length
Design Repeat: 19”
DEM-162
Design Repeat: 3-3/8”
CORNERS
3-3/4”
6-5/8”
94-1/2” Length
5-1/2”
OUTSIDE
DEM-162-B
INSIDE
DEM-162-A
Design Repeat: 11-3/4”
Pre-mitered corners
DEM-169 $34.93 per length ($4.37 per ft.)
2-1/2”
6-1/2”
7”
96” Length
Design Repeat: 3-3/4”
All dimensions are approximate. Cornice Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
8
Decorative Cornices
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
DEM-170
100% RECYCLED POLYSTYRENE
DEM-171
5-1/2”
4-1/2”
5-1/4”
7”
94-1/2” Length
7”
96” Length
Design Repeat: 2”
DEM-172
5-1/4”
Design Repeat: 1-1/4”
DEM-174
5-3/8”
5”
5-1/8”
7”
94-1/2” Length
5-1/4”
7-1/2”
94-1/2” Length
Design Repeat: 6”
Design Repeat: 2”
DEM-175
2-3/4”
CORNERS
6-7/8”
7-3/8”
INSIDE
DEM-174-A
96” Length
Design Repeat: 9-1/2”
OUTSIDE
DEM-174-B
Pre-mitered corners
DEM-177
6-1/4”
8”
94-1/2” Length
5-1/4”
Design Repeat:11-1/2”’
All dimensions are approximate. Cornice Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
9
Decorative Cornices
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
DEM-178
100% RECYCLED POLYSTYRENE
DEM-179
5-1/4”
5-1/8”
6-15/16”
6-7/8”
8-1/2”
94-1/2” Length
8-5/8”
Design Repeat: 4”’
96” Length
Design Repeat: 5-1/2”
DEM-183
DEM-182
5-1/2”
6-5/8”
7-7/8”
6-1/2”
9-5/8”
9-1/8”
94-1/2” Length
96” Length
Design Repeat: 6-1/4”
Design Repeat: 3-1/4”
DEM-184
8-7/8”
11-1/4”
7”
94-1/2” Length
Design Repeat:
4-1/8”
All dimensions are approximate. Cornice Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
10
Large Decorative Cornices
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
DEM-185
100% RECYCLED POLYSTYRENE
DEM-186
9”
6-5/16”
8-5/8”
10-1/16”
7-7/8”
12-1/2”
95-1/2” Length
94-1/2” Length
Design Repeat:
9-5/8”
Design Repeat:
7-7/8”
DEM-189
DEM-188
3-7/8”
10”
9”
96” Length
Design Repeat: 14”
11-1/8”
DEM-190
96” Length
Design Repeat: 9-1/2”
11-15/16”
16-5/16”
with
attached
corbel
MOULDING
WITHOUT
CORBEL
11-1/8”
96” Length
Design Repeat:
9-1/2”
DEM-190A
11-15/16”
16-5/16”
CORBELS
CAN ACCOMMODATE
10 CORBELS
DEM-190B
Corbels are
easily applied
with our adhesive
ADH1
10.6 oz tube
3-7/8” x
2-13/16” x
2-3/4”
4” x
2-3/4” x
2-5/8”
All dimensions are approximate. Cornice Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
11
Plain Cornices
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
100% RECYCLED POLYSTYRENE
RPS-2210
RPS-2205
2-1/2”
1-1/2”
1-1/2”
2-1/8”
96” Length
96” Length
DEM-220
RPS-2225
3”
3-1/8”
3”
4-1/8”
3-1/8”
4-1/2”
94-1/2”
Length
DEM-235
2-1/2”
3-1/2”
96” Length
DEM-230
3-1/2”
3-1/8”
3-3/8”
4-7/8”
3-1/2”
4-3/4”
94-1/2” Length
94-1/2” Length
DEM-240
5-3/8”
5-5/8”
2-1/8”
94-1/2” Length
•HIGH IMPACT
•Recommended blade 10” Blade, 200 Teeth
information can be found on page 3
All dimensions are approximate. Cornice Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
12
Plain Cornices
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
DEM-244
100% RECYCLED POLYSTYRENE
DEM-250
3-15/16”
4-3/4”
3-15/16”
4-3/8”
6-1/2”
5-1/2”
94-1/2” Length
94-1/2” Length
DEM-255
DEM-260
4-7/8”
5”
4-1/8”
6-7/8”
6-1/2”
94-1/2” Length
4-3/4”
96” Length
DEM-265
DEM-270
5”
6”
5”
7”
7-1/4”
4-1/8”
94-1/2” Length
94-1/2” Length
DEM-271
DEM-272
5-3/4”
5-3/4”
6-1/2”
8-5/8”
5-3/4”
94-1/2” Length
96” Length
Great for
indirect lighting
All dimensions are approximate. Cornice Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
13
Large Plain Cornices
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
100% RECYCLED POLYSTYRENE
DEM-273
7-7/8”
9-1/2”
5-5/16”
94-1/2” Length
CORNERS
OUTSIDE
DEM-273-B
INSIDE
DEM-273-A
Pre-mitered corners
DEM-280
DEM-275
7”
8-3/4”
6-3/4”
9-3/4”
12-3/8”
94-1/2” Length
8-3/4”
96” Length
DEM-283
9-13/16”
9-13/16”
14”
96” Length
All dimensions are approximate. Cornice Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
14
Combination Mouldings
Polyurethane DEM Mouldings
Two Sizes Available
6-13/16”
4-9/16”
DEM-260
DEM-260C
DEM-260V
6-1/2”
4-9/16”
9-9/16”
6-11/16”
DEM-275
DEM-275C
DEM-275V
Crown Moulding
DEM-260 length 96”
DEM-275 length 94-1/2”
Decorative Center Moulding
Close-up
DEM-260C length 96”
DEM-275C length 94-1/2”
Inside “V” Corner Moulding
Close-up
DEM-260V length 94”
DEM-275V length 94”
DEM-260V and DEM-275V can be mitered
to create 2 inside corners
CROWN
Combination Moulding Application
INSIDE “V”
MOULDING
All dimensions are approximate
15
DECORATIVE
CENTER
INSIDE “V”
MOULDING
Decorative Corners
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
DEM-10
DEM-11
OUTSIDE CORNER
CENTER
3” H 4-1/8” Proj.
3-1/8” W
3” H 3” Proj.
DEM-12
INSIDE CORNER
3” H 4-1/8” Proj.
Works with our DEM Mouldings:
DEM-105...page 4
DEM-111...page 4
100% RECYCLED POLYSTYRENE
DEM-113...page 4
DEM-114...page 4
DEM-116...page 4
Works with our RPS Mouldings:
RPS-2210...page 12
DEM-19
DEM-18
DEM-20
DEM-16
DEM-15
4-3/4” W
OUTSIDE CORNER
CENTER
4” W
INSIDE CORNER
4-3/4” H 6-3/4” Proj. 4-3/4” H 4-5/8” Proj. 4-3/4” H 6-3/4” Proj.
DEM-130...page 5
DEM-142...page 6
DEM-146...page 6
Works with our DEM Mouldings:
DEM-149...page 6
DEM-150...page 7
DEM-153...page 7
DEM-17
OUTSIDE CORNER
4” H
5-1/4 Proj.
DEM-115...page 4
DEM-120...page 4
DEM-122...page 4
DEM-155...page 7
DEM-244...page 13
CENTER
4” H
4” Proj.
INSIDE CORNER
4” H
5-1/4” Proj.
Works with our DEM Mouldings:
DEM-125...page 5
DEM-126...page 5
DEM-130...page 5
DEM-136...page 6
DEM-142...page 6
DEM-220...page 12
DEM-230...page 12
Works with our RPS Mouldings:
RPS-2210...page 12
DEM-21
DEM-22
OUTSIDE CORNER
4-3/4” H 6-1/2” Proj.
4-3/4” W
CENTER
DEM-23
DEM-13
INSIDE CORNER
4-3/4” H 4-3/4” Proj. 4-3/4” H 6-1/2” Proj.
Works with our DEM Mouldings:
DEM-130...page 5
DEM-136...page 6
DEM-142...page 6
DEM-146...page 6
DEM-147...page 6
DEM-150...page 7
DEM-153...page 7
RPS-2225...page 12
DEM-155...page 7
DEM-157...page 7
DEM-235...page 12
DEM-244...page 13
DEM-14
OUTSIDE CORNER
INSIDE CORNER
3-3/4” H 5” Proj.
DEM-120...page 4
DEM-122...page 4
3-3/4” H 5” Proj.
Works with our DEM Mouldings:
DEM-125...page 5
DEM-130...page 5
DEM-230...page 12
Works with our RPS Mouldings:
RPS-2210...page 12
All dimensions are approximate
16
RPS-2225...page 12
Large Decorative Drops
High Density Polyurethane
Our corner and center blocks allow you to install cornice
mouldings quickly and easily with no need for mitering.
Adding these architectural embellishments will highlight
the beauty and visual appeal that crown moulding offers.
• One piece pre-assembled, Corners & Centers.
No need to construct your own center and outside corner,
we’ve done the work for you, saving valuable time.
• Primed and ready for paint.
• Lightweight and easy to install, corners and centers can be
cut with a saw, nail and glue just like wood.
3-1/16”
3-1/16”
3-1/16”
3-1/16”
6-3/16”
3-7/8”
6-3/16”
3-1/16”
3-1/16”
6-3/16”
7-3/4”
3-7/8”
DEM-30
INSIDE
CORNER
DEM-32
OUTSIDE
CORNER
DEM-31
CENTER
Crown Moulding cannot exceed 3-3/16” height and 3” projection
Many great crown options can be found on pages 4-5
5-1/2”
5-1/2”
5-1/2”
5-1/2”
11-1/8”
11-1/8”
6-7/8”
11-1/8”
5-1/2”
5-1/2”
13-3/4”
6-7/8”
ADH1
10.6 oz tube
PL Premium Adhesive
Approximate adhesive yields*
Mouldings 2” + Under – 60’
Mouldings 2 - 5” – 45’
Mouldings 5” + Over – 30’
*Yields are approximate and
based on average conditions
and installation technique.
DEM-34
CENTER
DEM-33
INSIDE
CORNER
Crown Moulding cannot exceed 6-3/4” height and 5-1/2” projection
Many great crown options can be found on pages 8-9
All dimensions are approximate
17
DEM-35
OUTSIDE
CORNER
Decorative Panel Mouldings
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
DEM-303
DEM-303F - Flexible
5/8”
1”
Max Radius 8”
96” Length Design Repeat: 7/8”
RPS-3305
100% RECYCLED POLYSTYRENE
93” Length Design Repeat: 7/8”
RPS-3307
3/8”
7/8”
1-1/4”
1-3/8”
96” Length Design Repeat: 1”
DEM-311
Corner Available:
DEM-305A, See Page 23
96” Length Design Repeat: 2-1/4”
3/4”
1-5/8”
94-1/2” Length Design Repeat: 2-1/2”
DEM-313
1-1/8”
1-5/8”
94-1/2” Length Design Repeat: 10”
DEM-314
Corner Available:
DEM-313A, See Page 23
DEM-315
3/4”
1”
1-7/8”
96” Length
Design Repeat: 7”
1-7/8”
Over Corner Available:
DEM-314A & DEM-314-L/R, See Page 23
RPS-3319
94-1/2” Length Design Repeat: 2-3/8”
Corner Available:
DEM-315A, See Page 24
5/8”
2”
•HIGH IMPACT
blade 10” Blade, 200 Teeth
•Recommended
96” Length
information can be found on page 3
Design Repeat: 1-3/4”
All dimensions are approximate. Panel Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
18
Decorative Panel Mouldings
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
DEM-320
100% RECYCLED POLYSTYRENE
DEM-321
7/8”
3/4”
2”
2-3/8”
Corner Available:
DEM-320A, See Page 24
96” Length Design Repeat: 1-3/8”
DEM-322
94-1/2” Length Design Repeat: 1-3/8”
DEM-323
3/4”
3/8”
2”
2-1/2”
96” Length Design Repeat: 1-1/2”
94-1/2” Length
DEM-326
Corner Available:
DEM-321A, See Page 24
Design Repeat: 1-1/4”
DEM-327
1”
1/2”
2-3/4”
96” Length
3”
Design Repeat: 1/2”
Dots 24 per 12”
94-1/2” Length Design Repeat: 5-1/2”
DEM-328
1-1/8”
3”
96” Length Design Repeat: 7”
•HIGH IMPACT
blade 10” Blade, 200 Teeth
•Recommended
information can be found on page 3
All dimensions are approximate. Panel Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
19
Decorative Panel Mouldings
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
100% RECYCLED POLYSTYRENE
DEM-331
DEM-330
3/4”
1”
3-1/8”
3”
96” Length Design Repeat: 3/4”
DEM-332
94-1/2” Length Design Repeat: 1-3/4”
DEM-336
1”
Corner Available:
DEM-331A, See Page 24
1-1/4”
4”
3-1/2”
96” Length
Design Repeat: 5”
Corner
Available:
DEM-336A,
See Page 24
94-1/2” Length Design Repeat: 4”
Decorative Friezes
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
DEM-333
100% RECYCLED POLYSTYRENE
DEM-334
3/4”
5/8”
5”
4-3/8”
96” Length Design Repeat: 12”
94-1/2” Length Design Repeat: 6-1/4”
DEM-335
DEM-390
7/8”
1”
5-1/8”
7-1/16”
96” Length Design Repeat: 12”
94-1/2” Length Design Repeat: 19”
DEM-392
DEM-397
1”
1”
7-7/8”
7-1/16”
96” Length Design Repeat: 5-1/8”
96” Length Design Repeat: 1”
All dimensions are approximate. Panel Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
20
Plain Panel Mouldings
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
RPS-4400
100% RECYCLED POLYSTYRENE
RPS-4405
11/16”
5/8”
1-1/2”
1-5/8”
96” Length
Corner Available:
DEM-400A, See Page 25
96” Length
RPS-4410
DEM-415
Corners Available:
DEM-405B,C,D,E,F, See Page 25
5/8”
1/2”
2”
1-5/8”
96” Length
DEM-419
Corner Available:
DEM-410A, See Page 25
94-1/2” Length
DEM-420
13/16”
7/8”
2-9/16”
94-1/2” Length
DEM-425
Corners Available:
DEM-415A, DEM-415B
See Page 25
3-1/8”
Corner Available:
DEM-419A, See Page 25
94-1/2” Length
1”
3-3/8”
94-1/2” Length
•HIGH IMPACT
blade 10” Blade, 200 Teeth
•Recommended
information can be found on page 3
All dimensions are approximate. Panel Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
21
Panel Mouldings / Accessories
Polyurethane DEM Mouldings
100% Recycled Polystyrene RPS Mouldings
Mitreless Cover & Butt Joint Corner
The 90˚ Mitreless Corner Cover & 180˚ Mitreless Straight Cover
These products are decorative and designed to eliminate mitering and butt joints.
The covers will hide any imperfections on moulding edges and save time on installation.
Small 90º Mitreless
Corner Cover
Large 90 º Mitreless
Corner Cover
Our corners allow for miscuts up to 1/4”
180 º Mitreless
Straight
Cover
The 90º Butt Joint Corner & 180˚ Straight Butt Joint
When two ends of material are joined by butting them together using adhesive and caulk
or other type of filler. These items need to have a tight fit and may require sanding,
build up and caulking.
90 º Butt Joint Corner
180 º Straight Butt Joint
All dimensions are approximate. Panel Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
22
Panel Mouldings / Accessories
Polyurethane - DEM Mouldings
100% Recycled Polystyrene - RPS Mouldings
RPS-3305
1-1/4” x 3/8” x 96”
90º Butt Joint Corner
DEM-313
1-5/8” x 1-1/8” x 94-1/2”
90º Butt Joint Corner
DEM-305A
8-1/2” x 8-1/2”
DEM-314
1-7/8” x 3/4” x 96”
90º Mitreless Corner Covers
DEM-313A
8-7/8” x 8-7/8”
DEM-314A
14-1/4” x 14-1/4”
DEM-314-L/R
16” W x 18” H
Left and Right
Shown with DEM-314A
All dimensions are approximate. Panel Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
23
Panel Mouldings / Accessories
Polyurethane - DEM Mouldings
100% Recycled Polystyrene - RPS Mouldings
DEM-315
1-7/8” x 1” x 94-1/2”
90º Butt Joint Corners
DEM-320
2” x 7/8” x 96”
90º Mitreless Corner Cover
3-1/8” x 3/4” x 94-1/2”
90º Butt Joint Corner
16-1/8” x 16-1/8”
DEM-331B
10-1/2” x 11”
DEM-315A
9” x 9” x 1-1/4”
DEM-320A
DEM-321
2-3/8” x 3/4” x 94-1/2”
90º Butt Joint Corner
DEM-315F
12-3/4” x 12-3/4” x 7/8”
DEM-331
19-7/8” x 19-7/8”
DEM-331A
10-1/4” x 10-1/4”
DEM-321A
DEM-315E
10” x 10” x 15/16”
DEM-336
4” x 1-1/4” x 96”
90º Mitreless Corner Cover
DEM-315C
9-7/8” x 9-7/8” x 1-1/8”
Rosette
11-3/8” x 11-3/8”
2-1/2” Dia. x 1/2” Thick
DEM-336A
DEM-315D
All dimensions are approximate. Panel Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
24
Panel Mouldings / Accessories
Polyurethane - DEM Mouldings
100% Recycled Polystyrene - RPS Mouldings
RPS-4400
1-5/8” x 11/16” x 96”
RPS-4405
1-1/2” x 5/8” x 96”
90º Mitreless Corner Cover
90º Mitreless Corner Cover
3” x 3”
Hand
Carved
Wood
DEM-400-E
DEM-415
2” x 5/8” x 94-1/2”
90º Mitreless Corner Cover
9” x 9”
10” x 10”
DEM-415A
DEM-405D
180º Mitreless Corner Cover
Hand
Carved
Wood
3-1/4” x 2-3/4”
DEM-400-F
90º Butt Joint Corner
5-1/16” x 5-1/16”
DEM-400A
90º Mitreless Corner Cover
3-1/8” x 3-1/8”
DEM-405-E
Hand
Carved
Wood
180º Mitreless Straight Cover
180º Mitreless Straight Cover
3-1/4” x 2-3/4”
DEM-405-F
Hand
Carved
Wood
15” x 4”
DEM-415B
180º Butt Joint Corner
6-1/8” x 6-1/8”
DEM-405C
DEM-419
2-9/16” x 13/16” x 94-1/2”
7-3/8” x 7-3/8”
DEM-400B
180º Straight Butt Joint
90º Mitreless Corner Cover
Shown with DEM-400A
9-1/4” x 4-3/8”
RPS-4410
DEM-405B
1-5/8” x 1/2” x 96”
90º Butt Joint Corner
11-3/8” x 11-3/8”
DEM-419A
7-3/4” x 7-3/4”
DEM-410A
All dimensions are approximate. Panel Mouldings must be purchased in full length pieces. Sample Pieces are available in 6”-8” lengths.
25
Case Mouldings
Polyurethane DEM Mouldings
DEM-430
100% RECYCLED POLYSTYRENE
DEM-394
1-1/8”
1-3/8”
3-1/2”
7-3/4”
94-1/2” Length
96” Length Design Repeat: 1-1/2”
DEM-396
1-3/8”
7-3/4”
96” Length
Base Mouldings
Polyurethane DEM Mouldings
Polystyrene RPS Mouldings
RPS-4475
DEM-435
DEM-435-F - Flexible
100% RECYCLED POLYSTYRENE
1/2”
1/2”
5-5/8”
4”
94-1/2” Length
Matches WM163E
10” Max Radius on Flexible
Base Moulding
DEM-485
96” Length
9/16”
7-3/8”
1”
94-1/2” Length
Outside Corner
Inside Corner
DEM-485OC
DEM-485IC
7-3/8”
4-5/16” x 4-5/16” x 1”
7-3/8”
4-3/4” x 4-3/4” x 1”
•HIGH IMPACT
blade 10” Blade, 200 Teeth
•Recommended
information can be found on page 3
All dimensions are approximate
26
Decorative Medallions
Polyurethane Architectural Elements
DEM-510
DEM-513
12” Dia.
15” Dia.
Projection:
1-1/8”
Projection:
1-3/4”
DEM-514
DEM-519
18” Dia.
15-1/2” Dia.
Projection:
1-1/2”
ID: 3-5/8”
DEM-522
DEM-516
16-1/2” Dia.
Projection:
1-1/2”
18” Dia.
Projection:
1-1/2”
ID: 3-5/8”
DEM-528
DEM-525
18” Dia.
18” Dia.
Projection: 1-1/2”
ID: 3-5/8”
Projection: 1-1/2”
ID: 3-5/8”
DEM-531
18” Dia.
Projection: 1-7/8”
ID: 3-5/8”
All dimensions are approximate
27
Decorative Medallions
Polyurethane Architectural Elements
DEM-537
DEM-534
18” Dia.
18” x 18”
Projection:
1-3/8”
ID: 3-5/8”
Projection: 1-5/8”
ID: 3-5/8”
DEM-540
DEM-543
19” Dia.
20-1/2” Dia.
Projection: 1-1/2”
Projection:
1-5/8”
DEM-546
DEM-549
21” Dia.
Projection: 1-3/8”
22-5/8” Dia.
Projection:
1-3/4”
DEM-552
DEM-555
23-5/8” Dia.
Projection:
2-3/4”
23-5/8” Dia.
Projection:
3-1/2”
All dimensions are approximate
28
Decorative Medallions
Polyurethane Architectural Elements
DEM-561
DEM-558
24” Dia.
Projection: 3”
23-5/8” Dia.
Projection: 2-1/8”
ID: 3-5/8”
DEM-564
DEM-567
24-1/4” Dia.
Projection: 2”
27-1/8” Dia.
Projection: 2-1/2”
DEM-570
DEM-573
29-1/8” Dia.
Projection: 1-1/2”
28-1/8” Dia.
Projection: 1-7/8”
DEM-576
DEM-579
31-1/2” Dia.
Projection:
1-7/8”
30” Dia.
Projection:
2-3/8”
DEM-582
DEM-585
37-1/2” Dia.
Projection: 3-1/2”
32-5/8” Dia.
Projection: 2”
All dimensions are approximate
29
Decorative Medallions
Polyurethane Architectural Elements
DEM-590
DEM-592
Long Side: 17”
Short Side: 12”
Projection: 1-5/8”
Long Side: 18-1/2”
Short Side: 13-1/2”
Projection: 2”
DEM-594
DEM-596
Long Side: 30-1/2”
Short Side: 20”
Projection: 1-1/2
Long Side: 23-3/4”
Short Side: 12-1/4”
Projection: 1-3/4”
DEM-598
Long Side: 36”
Short Side: 26”
Projection: 1-5/8”
Stair Brackets
Polyurethane Architectural Elements
Note* All brackets shown are “Right” brackets
DEM-675R
DEM-675L
8-5/8” x 6-1/4” x 5/8”
DEM-678R
DEM-678L
11” x 7” x 5/8”
DEM-681R
DEM-681L
10-5/8” x 7” x 5/8”
All dimensions are approximate
30
DEM-684R .
DEM-684L
8” x 6” x 3/4”
Decorative Recessed
Ceiling Domes
Polyurethane Architectural Elements
DEM-911
DEM-912
10-7/16”
9-13/16”
10-7/8”
9-13/16”
3-9/16”
39-3/8”
40”Dia x 10”Deep x 3-1/2” Rim
39-3/8”
40”Dia x 10”Deep x 3-1/2” Rim
3-9/16”
Ceiling Dome Insert
Ceiling Dome Insert
DEM-900-1
13-3/8” x 1-3/4”
works with : DEM-911
DEM-912
DEM-900-3
12-13/16” x 1-1/2”
works with : DEM-911
DEM-912
DEM-900-2
20-1/2” x 2-9/16”
works with : DEM-918
DEM-919
used with DEM-918
DEM-900-4
18-1/8” x 1-3/4”
works with : DEM-918
DEM-919
DEM-919
DEM-918
53”Dia x 13”Deep x 3-3/4” Rim
14-9/16”
52-3/4”
13-3/16”
14-9/16”
13-3/16”
3-3/4”
3-3/4”
DEM-923
62”Dia x 14-1/2”Deep x 3/4”Lip
14-9/16”
62-3/16”
15-5/8”
13/16”
All dimensions are approximate
31
52-3/4”
53”Dia x 13”Deep x 3-3/4” Rim
Decorative Recessed
Ceiling Domes
Polyurethane Architectural Elements
DEM-908
36”Dia x 3”Deep x 4” Rim
26-15/16”
3-15/16”
3-1/8”
3-15/16”
3-1/8”
35-7/16”
DEM-905
27”Dia x 3”Deep x 1” Rim
3-15/16”
1”
DEM-922
60”Dia x 14”Deep x 5-1/2” Rim
3-15/16”
13-3/4”
44-1/2”
3-1/8”
15-9/16”
4-1/8”
60-1/4”
DEM-915
44”x 36”Elliptical x 3”Deep x 4” Rim
5-1/2”
DEM-929
DEM-926
80”Dia x 18”Deep x 5” Rim
71”Dia x 10”Deep x 3-1/2” Rim
28” *Medallion is Part of Mold
28” *Medallion is Part of Mold
18-1/8”
70-7/8”
10-1/4”
4-7/16”
3-9/16”
Surface Mounted Ceiling Dome
Polyurethane Architectural Elements
DEM-940
28-7/8”Dia x 4-5/16”Deep
Hole Dia: 4-3/8”
Hole Thickness: 1-3/4”
Inside Dia: 22-1/8”
All dimensions are approximate
32
80-5/16”
18-1/8”
14-3/16”
Recessed Niches
Polyurethane Architectural Elements
DEM-602
DEM-605
TRANSLUCENT
SHELF FOR
UPLIGHTING
26-1/2” W x 52” H
DEM-608
27-1/2” W x 48” H
16-3/4” W x 27-1/2” H
C
F
B
D
A
E
G
H
* DEM-611
I
PART #
DEM-602
DEM-605
DEM-608
DEM-611
Niche
shown
without
included
decorative
adjustable
trim pieces.
37-1/2” W x 69” H
A
B
C
D
E
F
G
H
15-1/4” 5-3/8” 23-3/8” 11-3/16” 3-1/2” 22-3/4” 16-3/4” 3-7/8”
23-1/2”
8”
43-1/4”
18”
6-1/8”
39”
26-3/8”
8”
23-1/2”
8”
43-1/4”
18”
6-1/8”
39”
28”
4”
35-1/4” 12” 63-5/8” 27-5/8” 11”
58”
37-1/2” 3-3/4”
DEM-611
shown
I
3-1/2”
9-1/4”
6-1/4”
5-3/8”
(Accent pieces included w/Niche)
* The 3 accent pieces
shown above can be placed on
the face of the frame of your
choosing, allowing you to
create your own unique look.
Niche shown
with center
decorative trim.
Please refrain from cutting the hole for your niche until you have actual niche for exact measurements.
Surface Mounted Niches
No Cutting!
If You Can Hang a Picture, You Can Hang a Niche!
•
•
•
•
PART #
Surface Mounted Niche Dimension Chart
No construction necessary.
As simple as hanging a picture.
Easily installed without having to cut a hole.
Pre-attached keyhole hangers.
A
B
C
D
E
F
G
H
I
DEM-635 21-1/8” 19-1/4” 13-3/4” 28-5/8” 34” 2-1/2” 5-7/8” 4-3/8” 23-1/2”
All dimensions are approximate
33
DEM-635
Decorative Corbels
These DECORATIVE high density smooth corbels are lightweight, primed and ready to paint.
A
D
C
B
E
G
F
I
H
A
B
C
D
E
F
G
H
I
J
PART #
DCOR-05-XS
DCOR-07-XS
DCOR-12-XS
DCOR-15-XS
DCOR-20-XS
DCOR-23-XS
DCOR-25-XS
DCOR-30-XS
DCOR-35-S
DCOR-38-S
HEIGHT
3-13/16”
4-1/2”
5-1/2”
5-3/4”
5-3/4”
6-1/2”
6-3/8”
7-7/8”
7-3/4”
8-1/4”
WIDTH
2-9/16”
3”
4”
4-1/8”
3-7/16”
4-5/16”
4-3/8”
3-1/4”
4-7/8”
5-3/16
DEPTH KEYHOLE
1-1/2”
No
1-3/4”
No
2”
No
2-1/4”
No
2-3/4”
No
2-1/4”
No
2-11/16”
Yes
2-1/2”
No
2-3/8”
Yes
3-1/4
Yes
D
H
All dimensions are approximate
34
W
J
Decorative Corbels
These DECORATIVE high density smooth corbels are lightweight, primed and ready to paint.
L
M
N
O
K
S
D
W
Q
P
R
H
K
L
M
N
O
P
Q
R
S
PART #
DCOR-40-S
DCOR-45-S
DCOR-55-S
DCOR-61-M
DCOR-65-M
DCOR-80-L
DCOR-86-L
DCOR-91-XL
DCOR-95-XL
HEIGHT WIDTH
8-1/8”
4-7/8”
9-3/8”
6-3/16”
9-1/2”
4-13/16”
11”
7-13/16”
12-1/8”
5-1/8”
14-5/8”
8-1/4”
17-3/8” 5-13/16”
26-7/8”
5”
41-1/2”
8-1/8”
DEPTH
3-7/16”
4-5/8”
2-1/2”
3-3/4”
5-5/16”
5”
4-1/8”
5”
7-1/4”
KEYHOLE
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
DCOR-95-XL
All dimensions are approximate
35
Window
Casings
Pilasters
Polyurethane Architectural Elements
Polyurethane Architectural Elements
DEM-820 Series
DEM-705 Series
DEM-820A
4-3/4” H x 4-3/4” W
3/4” Projection
DEM-705A
6-1/8” H x 10-1/2” W
3” Projection
DEM-705B
3” H x 9-3/8” W
2-1/4” Projection
CASINGS
CAPITALS
ROSETTES
DEM-705 Series
Pilaster Capitals
To Choose From:
DEM-705C
PILASTER
7-3/8” H x 8-1/4” W
2-1/4” Projection
DEM-820
PLINTH
PLINTHS
96” L x 4-1/2” W
3/4” Projection
DEM-705
78-3/4” L x 5-3/4” W
5/8” Projection
DEM-820C
7-3/4” H x 4-3/4” W
1” Projection
DEM-705F
12-1/8” H x 6-5/8” W
1” Projection
All dimensions are approximate
36
Massive Pilasters
Polyurethane Architectural Elements
DEM-710 Series
DEM-715 Series
DEM-720 Series
17” H x 21-5/8” W
7-1/2” Projection
25-1/4” H x 25-3/8” W
8-1/4” Projection
DEM-720A
DEM-715A
DEM-710A
CAPITALS
7-1/8” H x 17-1/2” W
2-5/8” Projection
DEM-710
78-3/4” L x 9-7/8” W
1-1/8” Projection
DEM-720
94-1/2” L x 17-3/4” W
1-1/2” Projection
DEM-715
78-3/4” L x 12-1/2” W
1-1/8” Projection
1-1/2”
17-3/4”
9-7/8”
1-1/8”
12-1/2”
PILASTERS
1-1/8”
DEM-715B
20-7/8” H x 15” W
2-1/8” Projection
PLINTHS
DEM-710B
6-1/4” H x 13-1/8” W
2-3/4” Projection
All dimensions are approximate
37
DEM-720B
31-5/8” H x 23-5/8” W
5-1/2” Projection
Door Surrounds & Accessories
Polyurethane Architectural Elements
• For Interior & Exterior Applications. • Will not split, decay, warp or rot. • Primed and ready to paint.
(When using as an exterior application, we recommend using a “UV” stabilized paint).
DEM-394
DEM-396
Must be purchased in full length pieces 1-3/8”
Must be purchased in full length pieces 1-3/8”
DEM-745
DEM-785-L
7-3/4”
7-3/4”
96” Length Design Repeat: 1-1/2”
DEM-733
96” Length
10-1/16”
9-3/4”
9-1/16”
8-1/4”
DEM-785-L (Left)
DEM-785-R (Right)
8-1/4”
8-1/4”
DEM-780-L (Left)
DEM-780-R (Right)
DEM-783-L (Left)
DEM-783-R (Right)
DEM-780-L
DEM-396
DEM-780-R
CAPITAL &
MOULDING
ASSEMBLY
86-5/8”
DEM-785-R
6-1/4”
1”
2-3/8”
8-5/8”
31-1/2”
7-3/4”
DEM-745
1-3/4” PROJECTION
21”
DEM-740
DEM-740
1-3/4” PROJECTION
DEM-783-L
DEM-733
6-7/8”
1-3/16” PROJECTION
FIELD SANDING REQUIRED
TO USE ACCESSORIES WITH
PANEL MOULDINGS
The examples shown
can be applied to most
entryways. Door opening
configurations may vary.
Please measure your
specific opening or
application.
All dimensions are approximate
38
DEM-783-R
ADJUSTABLE
7-3/4”
17-3/4”
DEM-394
Door Surrounds & Accessories
High Density Polyurethane Architectural Elements
• For Interior & Exterior Applications. • Will not split, decay, warp or rot. Primed and ready to paint.
(When using as an exterior application, we recommend using a “UV” stabilized paint).
6” & 9” CROSSHEADS
B
DEM-750
DEM-755
C
D
A
Can expand
up to
approximately
11’ using:
two DEM-755
+ one DEM-765
DEM-735
PILASTERS
DEM-730
CROSSHEADS _________________
PART #
A
B
DEM-750 59-15/16” 63-3/4”
DEM-755 67-3/4” 72-5/8”
C
3”
4”
D
6-1/8”
9”
B
C
A
KEYSTONES _______________________
WORKS WITH
A
B
C
CROSSHEAD
DEM-750
DEM-760 7-1/16” 5-3/4” 3-15/16”
6”
DEM-755
DEM-765 11-7/16” 8-1/4”
PART #
DEM-760
DEM-765
PILASTERS w/attached cap & adjustable plinth ______
PLINTH
DESCRIPTION
HEIGHT WIDTH PROJ. HEIGHT
Fluted Pilaster
85”
6-1/2” 2-3/4”
8-5/8”
DEM-730
87”
7”
2-1/8” 14-1/2”
DEM-735 Raised Panel Pilaster
PART #
DEM-765
DEM-755
85”
87”
ADJUSTABLE
ADJUSTABLE
14-1/2”
8-5/8”
6-1/2”
DEM-735
FIELD SANDING REQUIRED
TO USE ACCESSORIES WITH
PANEL MOULDINGS
All dimensions are approximate
39
7”
Polyurethane
Architectural
Elements
Give
All Your Projects
A Distinctive, Designers Finish.
#A960
CODE: DEM2013