parts manual - Alamo Industrial

Transcription

BOOM ARM MOWER
Published 4/04
Effective S/N 01108 - Current
PARTS MANUAL
ALAMO INDUSTRIAL
1502 E. Walnut
Seguin, Texas 78155
210-379-1480
© 2004 Alamo Group Inc.
Part No. 02968915P
TO THE OWNER/OPERATOR/DEALER
All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who
recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to
be used with all its safety equipment properly attached to minimize the chance of accidents.
BEFORE YOU START!! Read the safety messages on the implement and shown in your manual.
Observe the rules of safety and common sense!
WARRANTY INFORMATION:
Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form
in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card
and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic
failure with possible injury or death.
PARTS
SECTION
Parts Section - 1
PARTS ORDERING GUIDE
The following instructions are offered to help eliminate needless delay and error in processing
purchase orders for the equipment in this section.
1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the
basic machine featured in this manual. Part Numbers and Descriptions are given to help
locate the parts and quantities required.
2. The Purchase Order must include the name and address of the person or organization
ordering the parts, who should be charged, and if possible, the serial number of the machine
for which the parts are ordered.
3. The Purchase Order must clearly list the quantity of each part, the complete and correct part
number (be sure to include all periods), and the basic name of the part.
4. The Manufacturer reserves the right to substitute parts where applicable.
5. Some parts are unlisted items which are special production items not normally stocked and
are subject to special handling. Request a quotation for such parts before sending a
Purchase Order.
6. The Manufacturer reserves the right to change prices without prior notice.
NOTE:
Please refer to The Safety Section in the front of this Manual for the proper
Part Number when ordering Replacement Safety Decals.
For maximum safety and to guarantee optimum product reliability, always use
genuine Servis-Rhino Parts. The use of inferior replacement parts may cause
premature or catastrophic failure which could result in serious injury or death.
Direct any questions regarding parts to:
ALAMO INDUSTRIAL
1502 E. Walnut
Seguin, Texas 78155
830-379-1480
©2004 Alamo Group Inc.
Parts Section -2
PART NAME INDEX
BOOM ASY, 17 FOOT W/ ALLOY STEEL BOOM ............................................................................................................. 24
BOOM ASY, 17 FOOT W/ STD STEEL BOOM ................................................................................................................... 22
BOOM ASY, 21 FOOT W/ STD & ALLOY STEEL BOOM................................................................................................... 26
BOOM ASY, 24 FOOT W/ STD & ALLOY STEEL BOOM................................................................................................... 28
BUZZ BAR HEAD ASY - 48 INCH - S/N 01307 (11-01) & UP .......................................................................................... 106
BUZZ BAR HEAD ASY - 69 INCH - S/N 01307 (11-01) & UP .......................................................................................... 102
BUZZ BAR HEAD ASY - 90 INCH - S/N 01306 (10-01) & DOWN...................................................................................... 94
BUZZ BAR HEAD ASY - 90 INCH - S/N 01307 (11-01) & UP ........................................................................................... 98
BUZZ BAR SPINDLE ASY - S/N BB-01219....................................................................................................................... 110
CYL ASY, DIPPER - 17 FT - P/N 02979920 ....................................................................................................................... 44
CYL ASY, DIPPER - 21 & 24 FT. - P/N 02967174A ........................................................................................................... 45
CYL ASY, LIFT - P/N 02967173A ........................................................................................................................................ 43
CYL ASY, SWING - P/N 02967172A ................................................................................................................................... 46
CYL ASY, TILT - P/N 02967175A ........................................................................................................................................ 47
DITCHER BLADE CARRIER ASY. ...................................................................................................................................... 93
DITCHER HEAD ASY........................................................................................................................................................... 89
DITCHER HOUSING ASY.................................................................................................................................................... 91
DITCHER SPINDLE ASY. .................................................................................................................................................... 92
FILTER ASY. P/N 02976066 ................................................................................................................................................ 13
FLAIL AXE DOOR CYLINDER ASY. - P/N 02970710A ...................................................................................................... 82
FLAIL AXE HEAD ASY. (ITEM 1 THRU 40) ........................................................................................................................ 78
FLAIL AXE HEAD ASY. (ITEM 41 THRU 51) ...................................................................................................................... 80
FLAIL AXE HEAD HOSE CONNECTIONS .......................................................................................................................... 83
FML 100H FLAIL HEAD ASY - (ITEM 1 THRU 50)............................................................................................................ 84
FML 100H FLAIL HEAD ASY - (ITEM 51 THRU 91) ........................................................................................................... 86
FML 100H SPINDLE ASY. - P/N 02969661......................................................................................................................... 88
GRASS FLAIL ASY. ............................................................................................................................................................. 70
GRASS FLAIL CUTTERSHAFT ASY. .................................................................................................................................. 75
GRASS FLAIL CUTTERSHAFT BEARING ASY.................................................................................................................. 76
GRASS FLAIL PULLEY ASY ............................................................................................................................................... 74
GRASS FLAIL ROLLER ASY ............................................................................................................................................... 77
GRASS FLAIL SUB-ASY...................................................................................................................................................... 72
HIGH FRAME ASY, 2 WD & 4 WD ........................................................................................................................................ 5
HOSE SCHEMATIC, 17 FOOT BOOM ARM ....................................................................................................................... 30
HYDRAULIC TANK P/N 02966767 ...................................................................................................................................... 14
JOYSTICK CONSOLE ASY. P/N 02975446B (OLD STYLE) .............................................................................................. 17
JOYSTICK CONSOLE ASY. P/N 02975446C (NEW STYLE) ............................................................................................. 15
KING POST SUB-ASY ........................................................................................................................................................... 6
MOUNTING COMPONENTS / COMMON PARTS BOX........................................................................................................ 7
MOUNTING COMPONENTS / COMMON PARTS BOX (CONTINUED).............................................................................. 9
OIL RESERVOIR ASY.......................................................................................................................................................... 11
SERVO CNTRLD PISTON PUMP P/N 02969527A (ITEM 1 THRU 50) ............................................................................. 18
SERVO CNTRLD PISTON PUMP P/N 02969527A (ITEM 51 THRU 80) ........................................................................... 20
TIMBERCAT HEAD ASY (ITEMS 1 THRU 39).................................................................................................................. 111
TIMBERCAT HEAD ASY. (ITEMS 40 THRU 68)............................................................................................................... 113
VALVE ASY - 5 SPOOL FIXED DISPLACEMENT ............................................................................................................. 36
VALVE ASY - OPEN & CLOSED CENTER SYS................................................................................................................. 40
VALVE ASY - SOLENOID .................................................................................................................................................... 42
VALVE ASY - 5 SPOOL LOAD SENSE............................................................................................................................... 38
50 IN. ROTARY HEAD ASY................................................................................................................................................ 61
50 IN. DOOR CYL ASY - P/N 02961480A........................................................................................................................... 67
50 IN. ROTARY BLADE PAN ASY - P/N 02964457............................................................................................................ 68
50 IN. ROTARY MOTOR & SPINDLE ASY. ........................................................................................................................ 63
50 IN. ROTARY MOTOR ASY PARTS - P/N 02979881...................................................................................................... 65
50 IN. ROTARY SPINDLE ASY. P/N 02960553B................................................................................................................ 69
60 IN. DOOR CYL ASY - P/N 02961480A........................................................................................................................... 59
60 IN. ROTARY BLADE BAR ASY. P/N 02969230 ............................................................................................................ 60
60 IN. ROTARY HEAD ASY. S/N MR60-02050 & DOWN................................................................................................... 48
60 IN. ROTARY HEAD ASY. S/N MR60-02051 & UP ......................................................................................................... 50
60 IN. ROTARY HEAD SPINDLE ASY P/N 02968859A ..................................................................................................... 58
MACHETE - M/B 17,21,24 (APR-04)
Parts Section – 3
PART NAME INDEX
60 IN. ROTARY HEAD SUB-ASY. S/N MR60- 02050 & DOWN......................................................................................... 52
60 IN. ROTARY HEAD SUB-ASY. S/N MR60-02051 & UP ................................................................................................ 54
60 IN. ROTARY MOTOR ASY PARTS - P/N 02979881 S/N MR60-02051 & UP............................................................... 56
MACHETE - M/B 17,21,24 (APR-04)
Parts Section – 4
HIGH FRAME ASY, 2 WD & 4 WD
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PART NO.
QTY. 2 WD
QTY. 4 WD
DESCRIPTION
02978449
02978450
02978447
02978448
02978000
02978461
02975596
00013300
00002700
00001800
02960521
00037200
5312316
02968841
00725746
02742500
02962765
02965262
1
-1
-1
1
1
1
1
1
8
8
16
1
1
3
1
1
-1
-1
1
1
1
1
1
1
8
8
16
1
1
3
1
1
HIGH FRAME ASY, 2 WHL DRIVE
HIGH FRAME ASY, 4 WHL DRIVE
HIGH FRAME WLDMNT, 2 WHL DRIVE
HIGH FRAME WLDMNT, 4 WHL DRIVE
KING POST FRAME SUB-ASY
PIN WLDMNT
TUBE SPACER
BOLT
FLATWASHER
LOCKNUT
BOLT
LOCKNUT
FLATWASHER, HARDENED
CYLINDER ASY, LIFT CYL
DECAL, SPANISH TRANSLATION
ELBOW
DECAL. MULTI-HAZARD
DECAL, HOSE BURST
MACHETE - M/B 17,21,24 (APR-04)
Parts Section – 5
KING POST SUB-ASY
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
02978000
02975491
02978840
02975508
02975493
02968803
02978477
00748823
02975596
00002700
00001800
02966088
02978476
02968804
02956765
02963646
02023900
1
1
1
1
1
3
1
2
2
2
3
1
1
2
1
1
1
KING POST FRAME SUB-ASY
KING POST MOUNTING
CYLINDER ASY, SWING CYL.
PIN
KING POST, MACHINED
BUSHING, TEFLON
PIN WLDMNT
BOLT
TUBE SPACER
FLATWASHER
LOCKNUT
WASHER, THRUST
PIN WLDMNT
BUSHING, TEFLON
BOLT
BOLT
JAMNUT
MACHETE - M/B 17,21,24 (APR-04)
Parts Section – 6
MOUNTING COMPONENTS / COMMON PARTS BOX
MACHETE - M/B 17,21,24 (APR-04)
Parts Section – 7
MOUNTING COMPONENTS / COMMON PARTS BOX
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
*
35
36
*
*
*
*
*
*
*
*
*
*
*
*
PART NO.
QTY.
DESCRIPTION
02976759
02976766
00001800
00002700
00037200
00725336
00725337
02958488
00726119
00749130
02027400
02957039
02918600
02966634
02966639
02966641
02969032
02975446B
02975446C
02971381
002504
02976024
02976617
02974389
00011400
00011100
00015800
02961489
00059900
02970116
02968157
02968158
02968170
02961085
02753400
02976712
02976765
02968149
02968150
02968155
00012300
02968156
02973297*
00001300
00001800
00002700
00011100
00011400
00012101
00012200
00015800
00037200
00059900
002369
002508
--8
8
12
2
2
2
2
2
6
4
8
1
8
2
1
1
1
1
5
5
1
1
2
4
4
1
2
2
1
1
1
2
2
a/r
a/r
1
1
1
3
1
1
2
8
10
4
2
2
3
4
16
2
1
2
COMMON PARTS BOX, F/ OCFD VALVE
COMMON PARTS BOX, F/ CCLS VALVE
LOCKNUT
FLTWASHER
LOCKNUT
STRAP
PIN
COTTER PIN
BRASS WASHER F/ HINGE
BOLT
BOLT
BOLT
BOLT
BUMPER
MOUNT STRAP
MOUNT ANGLE
TANK & PUMP COVER
JOYSTICK CONSOLE ASY. (OLD STYLE)
JOYSTICK CONSOLE ASY. (NEW STYLE)
WIRING HARNESS (VALVE ON FRAME)
CONNECTOR
CONNECTOR
WIRE HARNESS (VALVE UNDER PUMP COVER)
ARM REST
BOLT
FLATWASHER
NUT
PIVOT PLATE
BOLT
FRAME TUBE
HOSE (W/ ORANGE TIE)
HOSE, (W/ RED TIE)
HOSE, (W/ BLUE TIE)
SLEEVING, F/ # 16 HOSES BOOM TO FRAME & FRAME TO PUMP
PLASTIC TIE ON
OCFD TANK & VALVE ASY.
CCLS TANK & VALVE ASY.
HOSE, LIFT CYL ROD (ORANGE TIE)
HOSE, LIFT CYL BASE (ORANGE W/ WHITE STRIPE TIE)
HOSE, SWING CYL ROD (GREEN TIE)
NUT, (IN ITEM 36)
HOSE, SWING CYL BASE (GREEN W/ WHITE STRIPE TIE)
HARDWARE KIT, (* INCLUDES ALL THE FOLLOWING ITEMS)
LOCKWASHER, (IN ITEM 36)
LOCKNUT, (IN ITEM 36)
FLATWASHER, (IN ITEM 36)
BOLT, (IN ITEM 36)
BOLT, (IN ITEM 36)
DECAL, MULTI-HAZARD (IN ITEM 36)
DECAL, ALAMO LOGO (IN ITEM 36)
Note: All items with * are included in hardware kit P/N 02973297 and are list as an inventory reference. These parts are
not shown in drawing of manual, for hardware location refer to instruction drawings that are included in hardware kit.
MACHETE - M/B 17,21,24 (APR-04)
Parts Section – 8
MOUNTING COMPONENTS / COMMON PARTS BOX (CONTINUED)
MACHETE - M/B 17,21,24 (APR-04)
Parts Section – 9
MOUNTING COMPONENTS / COMMON PARTS BOX (CONTINUED)
ITEM
PART NO.
QTY.
DESCRIPTION
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
00725336
00725337
00725338
00726119
00750227
02027400
02753400
02776600
02892000
02911900
02918600
02957039
02958241
02959010
02960766
02961085
02961306
02961489
02965093
02965262
02979473
02966639
02966641
02967827
02968157
02968158
02968170
02968808
02968915
02968954
02969525
02969559
02969560
02970117
02971123
02971569
02971788
02971791
02975446
02977046
03200285
5JRC1490
63096300
02975004
2
2
2
8
3
8
2
2
2
1
8
8
1
1
1
1
1
1
1
1
1
8
4
1
1
1
1
1
1
2
1
1
1
1
1
3
3
1
1
1
1
3
1
1
STRAP, (IN ITEM 36)
PIN, (IN ITEM 36)
COTTER PIN, (IN ITEM 36)
WASHER, BRASS SPECIAL, (IN ITEM 36)
BOLT, (IN ITEM 36)
PLASTIC TIE, (IN ITEM 36)
BOLT, (IN ITEM 36)
BOLT, (IN ITEM 36)
BOOM REST HOOK, (IN ITEM 36)
BOLT, (IN ITEM 36)
BOLT, (IN ITEM 36)
DECAL, TRACTOR OPERATOR, (IN ITEM 36)
PAMPLET, SAFETY MOUNT, (IN ITEM 36)
DECAL, ALAMO GROUP, (IN ITEM 36)
CORDURA SLEEVING, 54" LONG, (IN ITEM 36)
PIVOT PLATE WLDMNT, (IN ITEM 36)
DECAL, PROPER ENGINE SPEED, (IN ITEM 36)
DECAL, WARNING HOSE, (IN ITEM 36)
DECAL, AW ISO VG 100 TRAC, HYD FLUID, (IN ITEM 36)
BAR, MOUNT STRAP, (IN ITEM 36)
BAR, MOUNT ANGLE, (IN ITEM 36)
DECAL, MULTI-HAZZARD, (IN ITEM 36)
HOSE, #16 X 52" LONG W/ ORANGE TIE, (IN ITEM 36)
HOSE, # 16 X 52" LONG W/ RED TIE, (IN ITEM 36)
HOSE, # 16 X 52" LONG W/ BLUE TIE, (IN ITEM 36)
OPERATORS MANUAL, (IN ITEM 36)
DECAL, MACHETE, (IN ITEM 36)
DRAWING, INSTR. COUNTER WEIGHT, (IN ITEM 36)
BAR, BOOM STOP, (IN ITEM 36)
DRAWING, INSTR. BOOM STOP, (IN ITEM 36)
DRAWING, INSTR. FRAME RAIL, (IN ITEM 36)
DECAL, WARNING PRESSURE, (IN ITEM 36)
WASHER, WHEEL WEIGHT, (IN ITEM 36)
ROD, ALL THREAD, (IN ITEM 36)
DRAWING, INSTR. WHEEL WEIGHT, (IN ITEM 36)
JOYSTICK CONSOLE ASY. (IN ITEM 36)
MANUAL, EMI INDUSTRIAL, (IN ITEM 36)
DECAL, WATCH YOUR STEP, (IN ITEM 36)
PAINT, SPRAY CAN, (IN ITEM 36)
TIE ROD LUG, (IN ITEM 36)
Note: All items with * are included in hardware kit P/N 02973297 and are list as an inventory reference. These parts are
not shown in drawing of manual, for hardware location refer to instruction drawings that are included in hardware kit.
MACHETE - M/B 17,21,24 (APR-04)
Parts Section – 10
OIL RESERVOIR ASY
MACHETE - M/B 17,21,24 (APR-04)
OIL RESERVOIR ASY
ITEM
1
2
3
4
5
6
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
PART NO.
QTY.
DESCRIPTION
02976712
02976765
00011700
10119000
00750940
00023500
00752067
02041800
02825900
02043600
02822700
02976533
02976688
02976527
02976525
02969527A
02969527RB
02977086
02977199
02970206
02976524
02968164
02968165
02761100
02976767
02968894
02968895
02968896
02968922
02968923
02976066
10074000
32901C
02976523
03200587
63042700
02161400
00035900
02959372
02972106
02968167
--4
4
2
4
1
1
1
2
1
A/R
A/R
1
1
A/R
A/R
REF
REF
REF
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
2
2
1
1
1
OIL RESERVOIR ASY, OCFD VALVE
OIL RESERVOIR ASY, CCLS VALVE
LOCKWASHER
BOLT
LOCKNUT
FLATWASHER
ADAPTER, STRAIGHT
ELBOW, 90 DEG.
ADAPTER, ELBOW
ADAPTER, 45 DEG.
ELBOW
VALVE ASY, OCFD (FIXED DISPLACEMENT)
VALVE ASY, CCLS (LOAD SENSE)
VALVE MOUNT PLATE
HYDRAULIC HOSE
PUMP ASY, FRONT (NEW PUMP)
PUMP ASY, FRONT (REBUILT PUMP)
PUMP SEAL KIT
PUMP SHAFT SEAL
SOLENOID SERVO CONTROL
ADAPTER
HOSE
HOSE
ADAPTER, ELBOW
TANK ASY
PLASTIC TIE, RED
PLASTIC TIE, BLUE
PLASTIC TIE, ORANGE
PRESSURE FILTER HEAD & ELEMENT ASY
PRESSURE FILTER ELEMENT
FILTER VALVE ASY (F/ CYL. CONTROL SYSTEM)
BOLT
LOCKNUT
ADAPTER
PLUG, HEX
ADAPTER
ADAPTER
BOLT
HOSE
DECAL, INST. HYD HOSE
ADAPTER, STRAIGHT
MACHETE - M/B 17,21,24 (APR-04)
FILTER ASY. P/N 02976066
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
02976066
02976581
02978266
02976585
02651700
02976067
02976583
02976582
02976584
-1
1
1
1
1
1
1
1
FILTER ASY
VISUAL INDICATOR W/ BYPASS
O-RING
FILTER HEAD
O-RING
FILTER ELEMENT
BACK-UP RING
O-RING
BOWL
MACHETE - M/B 17,21,24 (APR-04)
HYDRAULIC TANK P/N 02966767
ITEM
PART NO.
QTY.
DESCRIPTION
1
3
4
5
6
7
8
9
10
11
12
14
02966767
00001300
00011800
00751984
02275700
02963659
02977040
02968166
02968879
02968880
02969917
63081000
02976242
-4
4
6
1
1
1
1
1
1
6
1
1
HYDRAULIC TANK SUB-ASY
LOCKWASHER
BOLT
STAR WASHER
PIPE TEE
PLUG, MAGNETIC
TANK WLDMNT
STRAINER, SUCTION
FILLER / BREATHER CAP ASY.
GAUGE, SIGHT & TEMPERATURE
MACHINE SCREW
REDUCER BUSHING
TANK COVER PLATE
MACHETE - M/B 17,21,24 (APR-04)
JOYSTICK CONSOLE ASY. P/N 02975446C (NEW STYLE)
MACHETE - M/B 17,21,24 (APR-04)
JOYSTICK CONSOLE ASY. P/N 02975446C (NEW STYLE)
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
4
5
6
7
8
9
10
10A
10B
11
12
13
14
15
16
17
18
19
02975446C
02981020
02981021
02981022
02981023
02981024
02981025
02981026
02981027
02977642
02977645
02977646
02977043
02981028
02981029
02981031
02981032
02981033
02981030
02977644
02977643
1
1
1
2
2
1
1
1
1
1
17
4
1
1
1
1
1
1
1
1
1
JOYSTICK CONSOLE ASY. W/ COMPONENTS (NEW STYLE)
LED DISPLAY LIGHT, RED
DECAL, JOYSTICK OPERATION CONSOLE
SWITCH, MOMENTARY PUSH BUTTON, RED
SWITCH, MOMENTARY PUSH BUTTON, BLACK
SOCKET RELAY, (INSIDE CONSOLE NOT SEEN)
RELAY, SPDT 12VDC 20A
CIRCUIT BREAKER, 10A PANEL MOUNT
BOOT, CIRCUIT BREAKER COVER
CONNECTOR, RECEPTACLE
PIN, 16-18 AWG
PIN, 12AWG
SWITCH ROCKER DPDT W/GREEN LED
SWITCH, PUSH PULL
JOYSTICK ASY. (W/O CONSOLE)
HANDLE SUB-ASY.
DECAL, SWITCH OPERATION HANDLE
PUSH BUTTON FACE PLATE SUB-ASY.
SWITCH, MOMENTARY PUSH BUTTON
LOCKWASHER
CONNECTOR NUT
MACHETE - M/B 17,21,24 (APR-04)
JOYSTICK CONSOLE ASY. P/N 02975446B (OLD STYLE)
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
02975446B
02977043
02977044
02979565
02979566
02977642
02977643
02977644
02977645
02977646
02977647
02977648
02977649
02977650
-1
1
1
1
1
1
1
17
4
1
1
1
1
JOYSTICK CONSOLE ASY.
ROCKER SWITCH
PUSH-PULL MOMENTARY SWITCH
JOYSTICK, PROPORTIONAL
BOX
CONNECTOR
PANEL, NUT
LOCKWASHER
PIN, 16-18 AWG
PIN, 12 AWG
FUSE HOLDER
RELAY, DPDT
RELAY, SPDT
RED LED
MACHETE - M/B 17,21,24 (APR-04)
SERVO CNTRLD PISTON PUMP P/N 02969527A (ITEM 1 THRU 50)
MACHETE - M/B 17,21,24 (APR-04)
ITEM
PART NO.
QTY.
DESCRIPTION
2
3
4
6
7
8
9
10
11
12
14
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
02969527A
02977418
02977419
02977420
02977421
02977422
02977423
02977424
02977425
02977426
02977427
02977428
02970209
02977430
02977431
02977432
02977433
02977434
02977525
02977434
02977436
02977437
02970208
02977439
02977440
02977526
02977527
02977528
02977529
02977530
02977531
02977532
02977533
02977534
02977535
02977441
02977536
02977537
02977325
02977551
02977442
02977444
02977449
02977443
02977445
02977446
02977538
-1
1
2
1
8
1
1
1
1
2
1
1
1
1
2
1
2
2
1
2
2
6
1
1
1
1
1
1
1
2
1
1
2
2
1
1
1
1
1
1
2
1
1
1
1
1
PISTON PUMP ASY, SERVO CONTROLLED
JAM NUT
RETAINING RING
RETAINING RING
SEAL WASHER
BOLT
ROTATING ASY
SERVO PISTON SUB-ASY
FOLLOWER, SERVO PISTON
COVER PLATE
GASKET, F/ COVER PLATE
GASKET, F/ HOUSING
GASKET, F/ CONTROL HSG
COVER PLATE
CAM PLATE SUB-ASY
RACE, THRUST
BEARING, THRUST
RELIEF VALVE SUB-ASY
O-RING
RELIEF VALVE SUB-ASY
BOLT
BOLT
BOLT
PLATE, VALVE
HOUSING, SUB-ASY
HOUSING
BEARING
PLUG, SUB-ASY
O-RING
CRADLE, SUB-ASY
DOWEL BUSHING
BUSHING
BOLT, BUTTON HEAD
BOLT
SEAL SUB-ASY
BACK PLATE SUB-ASY
BEARING, PRESS FIT
ROLL PIN
SHAFT, SPLINED DRIVE
KIT, A-FLANGE COVER PLATE
O-RING
BOLT
PLATE, COVER
O-RING
WASHER
PLUG SUB-ASY
O-RING
MACHETE - M/B 17,21,24 (APR-04)
MACHETE - M/B 17,21,24 (APR-04)
ITEM
PART NO.
QTY.
DESCRIPTION
51
52
53
54
57
58
59
60
61
62
63
64
65
66
67
68
69
72
73
74
75
76
77
78
79
80
02977540
02977541
02977447
02977539
02977448
02977199
02977450
02977543
02977544
02977545
02977546
02977547
02977548
02970207
02977451
02977452
02977453
02977456
02977457
02977458
02977459
02977460
02977461
02977462
02972835
02972836
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
3
1
2
1
1
8
4
1
1
1
PLUG
O-RING
PLUG
O-RING
KEY
SEAL, SHAFT
CHARGE PUMP ADAPTER SUB-ASY
BUSHING, PRESS FIT W/ 11 TOOTH SHAFT
PLUG
O-RING
SHIM
SPRING
POPPET
2 POSITION SERVO CONTROL SUB-ASY
GEROTOR, INNER RING
GEROTOR, OUTER RING
ORIFICE, CONTROL VALVE
COUPLER
RETAINING RING
PLUG SUB-ASY
WASHER
WASHER
WASHER
RING LOCK
CARTRIDGE VALVE ASY W/O COIL
COIL ASY
MACHETE - M/B 17,21,24 (APR-04)
BOOM ASY, 17 FOOT W/ STD STEEL BOOM
MACHETE - M/B 17,21,24 (APR-04)
BOOM ASY, 17 FOOT W/ STD STEEL BOOM
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
02979902
02979903
02979911
02979920
02979916
02979917
02979918
02968803
02968806
02972816
02968805
02965448
02919600
02971705
02971755
02971754
02971752
02971753
02971751
02971703
02979922
02979301
02964673
02968838
02980040
03200375
02980039
02980038
02970595
02971701
02971702
165020
00015800
02959154
00002700
000245
02968895
02968894
02968896
-1
1
1
1
1
1
7
1
1
1
2
2
1
2
1
1
1
1
1
1
1
1
1
1
6
1
1
6
2
2
2
6
3
4
4
4
4
4
BOOM ASY, 17 FT. (STD STEEL MATERIAL)
LIFT SECTION WELDMENT (STD STEEL)
DIPPER SECTION WLDMNT (STD STEEL)
CYLINDER ASY, DIPPER
HYDRAULIC TUBE, F/ 17 FOOT
BUSHING, TEFLON
CYLINDER & BEARING ASY, TILT
LINK ARM, MACHINED
LINKAGE ARM & BUSHING ASY.
ADAPTER, HYDRAULIC
CAP, HYDRAULIC (4FJ)
PIN WLDMNT, 12" LONG
PIN, CHROME 1-1/2" X 9-9/16" LONG
PIN WLDMNT, 14-15/16" LONG
COVER, HYD TUBE
CLAMP, HYD TUBE
BOLT
CYLINDER ROD GUARD ASY.
HYDRAULIC TUBE, 17 FOOT
CLAMP, TUBE 1 - POSITION
BOLT
NUT, SLOTTED
FLATWASHER
COTTER PIN
LOCKNUT
ADAPTER, HYD
FLATWASHER
BOLT
PLASTIC TIE, BLUE
PLASTIC TIE, RED
PLASTIC TIE, ORANGE
Note: The P/N 02979902 Boom Arm asy is constructed of the standard steel, see the next page for the optional T-1 Steel
boom arm asy.
MACHETE - M/B 17,21,24 (APR-04)
BOOM ASY, 17 FOOT W/ ALLOY STEEL BOOM
MACHETE - M/B 17,21,24 (APR-04)
BOOM ASY, 17 FOOT W/ ALLOY STEEL BOOM
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
02980034
02980033
02980029
02979920
02979916
02979917
02979918
02968803
02968806
02972816
02968805
02965448
02919600
02971705
02971755
02971754
02971752
02971753
02971751
02971703
02979922
02979301
02964673
02968838
03200375
02980038
02970595
02971701
02971702
165020
00015800
02959154
00002700
000245
02968895
02968894
02968896
02980039
02980040
-1
1
1
1
1
1
7
1
1
1
2
2
1
2
1
1
1
1
1
1
1
1
1
6
1
6
2
2
2
6
3
4
4
4
4
4
1
1
BOOM ARM ASY, ALLOY STEEL OPTION
LIFT SECTION WLDMNT, ALLOY STEEL OPTION
DIPPER SECTION WLDMNT, ALLOY STEEL OPTION
CYLINDER ASY. DIPPER
HYDRAULIC TUBE , F/ 17 FOOT
BUSHING, TEFLON
CYLINDER & BEARING ASY. TILT CYL.
LINK ARM MACHINED
LINKAGE ARM & BUSHING ASY.
ADAPTER, HYD.
CAP, HYD (4FJ)
COVER, HYD TUBE
CLAMP, HYD TUBE
BOLT
CYLINDER ROD GUARD ASY.
CLAMP, TUBE 1 - POSITION
BOLT
NUT, SLOTTED
FLATWASHER
COTTER PIN
LOCKNUT
ADAPTER, HYD.
FLATWASHER
BOLT
PLASTIC TIE, BLUE
PLASTIC TIE, RED
PLASTIC TIE, ORANGE
Note: P/N 02980034 is constructed using T-1 Steel and is an optional order item, see the previous page for the standard
Steel boom arm asy.
MACHETE - M/B 17,21,24 (APR-04)
BOOM ASY, 21 FOOT W/ STD & ALLOY STEEL BOOM
MACHETE - M/B 17,21,24 (APR-04)
ITEM
3
4
5
6
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
61
63
PART NO.
QTY.
DESCRIPTION
02968801
02970852
00002700
165020
000245
02970595
02971701
02964673
02968722
02970849
02972816
02971751
02971754
02971753
02971752
02971703
02971705
02971755
02968717
02968718
02968719
02968714
02968715
02968716
02972156
02968713
02970848
02968802
02968803
02968805
02968803
02968806
03200375
02959283
02971702
02968838
02965448
02959154
02919600
00015800
02968894
02968895
02968896
02979028
02972157
--8
2
8
6
2
1
1-AR
1-AR
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
7
1
4
1
12
2
2
1
2
3
2
7
4
4
4
1
1
BOOM ARM ASY, W/ STD STEEL BOOM
BOOM ARM ASY, W/ ALLOY STEEL BOOM
FLATWASHER
COTTER PIN
BOLT
BOLT
NUT, SLOTTED
BOLT
DIPPER SECTION WLDMNT, F/ STD STEEL BOOM
DIPPER SECTION WLDMNT, F/ ALLOY STEEL BOOM
LINK ARM WLDMNT
HYDRAULIC TUBE, DIPPER SECTION (RED TIE)
HYDRAULIC TUBE, DIPPER SECTION (ORANGE TIE)
HYDRAULIC TUBE, DIPPER SECTION (BLUE TIE)
HYDRAULIC TUBE, LIFT SECTION (RED TIE)
HYDRAULIC TUBE, LIFT SECTION (ORANGE TIE)
HYDRAULIC TUBE, LIFT SECTION (BLUE TIE)
COVER PLATE
LIFT SECTION WLDMNT, F/ STD STEEL BOOM
LIFT SECTION WLDMNT, F/ ALLOY STEEL BOOM
DIPPER CYLINDER ASY.
BEARING
LINKAGE ARM ASY, W/ BEARINGS
BEARING, (INCLUDED IN LINKAGE ARM ASY)
TILT CYLINDER ASY
CLAMP
TUBE CLAMP
WASHER
CYLINDER GUARD
BULK HEAD FITTING
ADAPTER ELBOW, 45 DEG.
BULK HEAD CAP NUT
LOCKNUT
PLASTIC TIE, RED (R)
PLASTIC TIE, BLUE (B)
PLASTIC TIE, ORANGE (OR)
BOLT
COVER
MACHETE - M/B 17,21,24 (APR-04)
MACHETE - M/B 17,21,24 (APR-04)
ITEM
3
4
5
6
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
61
63
PART NO.
QTY.
DESCRIPTION
02968861
02970853
00002700
165020
000245
02970595
02971701
02964673
02967380
02970851
02972816
02971751
02971754
02971753
02971752
02971703
02971705
02971755
02967947
02967948
02967949
02968145
02968146
02968147
02972157
02967640
02970850
02968802
02968803
02968805
02968803
02968806
03200375
02959283
02971702
02968838
02965448
02959154
02919600
00015800
02968894
02968895
02968896
02979028
02972158
--8
2
8
6
2
1
1-AR
1-AR
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
7
1
4
1
12
2
2
1
2
3
2
7
4
4
4
1
1
BOOM ARM ASY, F/ STD STEEL BOOM
BOOM ARM ASY, F/ ALLOY STEEL BOOM
FLATWASHER
COTTER PIN
BOLT
BOLT
NUT, SLOTTED
BOLT
DIPPER SECTION WLDMNT, F/ STD STEEL BOOM
DIPPER SECTION WLDMNT, F/ ALLOY STEEL BOOM
LINK ARM WLDMNT
HYDRAULIC TUBE, DIPPER SECTION (RED TIE)
HYDRAULIC TUBE, DIPPER SECTION (ORANGE TIE)
HYDRAULIC TUBE, DIPPER SECTION (BLUE TIE)
HYDRAULIC TUBE, LIFT SECTION (RED TIE)
HYDRAULIC TUBE, LIFT SECTION (ORANGE TIE)
HYDRAULIC TUBE, LIFT SECTION (BLUE TIE)
COVER PLATE
LIFT SECTION WLDMNT, F/ STD STEEL BOOM
LIFT SECTION WLDMNT, F/ ALLOY STEEL BOOM
DIPPER CYLINDER ASY.
BEARING
LINKAGE ARM ASY, W/ BEARINGS
BEARING, (INCLUDED IN LINKAGE ARM ASY)
TILT CYLINDER ASY
CLAMP
TUBE CLAMP
WASHER
CYLINDER GUARD
BULK HEAD FITTING
ADAPTER ELBOW, 45 DEG.
BULK HEAD CAP NUT
LOCKNUT
BOLT
COVER
MACHETE - M/B 17,21,24 (APR-04)
HOSE SCHEMATIC, 17 FOOT BOOM ARM
MACHETE - M/B 17,21,24 (APR-04)
ITEM
PART NO.
QTY.
DESCRIPTION
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
59
60
61
02979902
02980034
02753400
02980018
02980019
02906300
02969124
02969124
02961085
02980014
02980015
02980016
02980020
02980021
02980022
02980023
02968807
02968808
02956918
02979240
REF
REF
6
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
REF
1
BOOM ARM ASY, F/ STD STEEL BOOM
BOOM ARM ASY, F/ ALLOY STEEL BOOM
PLASTIC TIE
HOSE, 134" (SMALL) W/ YELLOW / WHITE TIE (YW)
HOSE, 134" (SMALL) W/ YELLOW TIE (Y)
HOSE SLEEVING, 48" LONG
HOSE, 60" (SMALL) W/ YELLOW / WHITE TIE (YW)
HOSE, 60" (SMALL) W/ YELLOW TIE (Y)
HOSE, (LARGE) - W/ RED TIE (R)
HOSE, (LARGE) - W/ BLUE TIE (B)
HOSE, (LARGE) - W/ ORANGE TIE (OR)
HOSE, (MEDIUM) - W/ BLUE TIE (B)
HOSE, (MEDIUM) - W/ BLUE / WHITE TIE (BW)
HOSE, (MEDIUM) - W/ RED TIE (R)
HOSE, (MEDIUM) - W/ RED / WHITE TIE (RW)
RUBBER GROMMET
CAP NUT, F/ SHIPPING ONLY
HOSE SLEEVING, 2-1/2" ID X 36" LONG
MACHETE - M/B 17,21,24 (APR-04)
MACHETE - M/B 17,21,24 (APR-04)
ITEM
PART NO.
QTY.
DESCRIPTION
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
59
60
02968801
02970852
02753400
02969121
02969122
02906300
02969123
02969124
02961085
02968159
02968160
02968827
02968151
02968152
02968153
02968154
02968807
02968808
02956918
REF
REF
6
1
1
1
1
1
2
1
1
1
1
1
1
1
2
1
REF
BOOM ARM ASY, STD STEEL
BOOM ARM ASY, OPT ALLOY STEEL
PLASTIC TIE
HOSE, 184" (SMALL) - W/ YELLOW / WHITE TIE (YW)
HOSE, 184" (SMALL) - W/ YELLOW TIE (Y)
RUBBER GROMMET
HOSE SLEEVING
MACHETE - M/B 17,21,24 (APR-04)
MACHETE - M/B 17,21,24 (APR-04)
ITEM
PART NO.
QTY.
DESCRIPTION
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
59
60
02968861
02970853
02753400
02969121
02969122
02906300
02969125
02969126
02961085
02968159
02968160
02968827
02968862
02968863
02968864
02968154
02968807
00751838
02956918
REF
REF
6
1
1
1
1
1
2
1
1
1
1
1
1
1
2
1
REF
BOOM ARM ASY, STD STEEL
BOOM ARM ASY, OPT ALLOY STEEL
PLASTIC TIE
RUBBER GROMMET
HOSE SLEEVING
MACHETE - M/B 17,21,24 (APR-04)
VALVE ASY - 5 SPOOL FIXED DISPLACEMENT
MACHETE - M/B 17,21,24 (APR-04)
VALVE ASY - 5 SPOOL FIXED DISPLACEMENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
02975810
02971379
63042700
02976532
02972113
02968850
02972177
02972179
02962213
02968850
02972209
02972210
02969398
02972208
02957416
02963637
02975438
02976531
-1
1
1
1
3
5
2
1
3
1
1
2
1
8
2
1
1
VALVE ASY, 5 SPOOL (OCFD)
VALVE ONLY, 5 SPOOL
ADAPTER, STRAIGHT
ADAPTER, ELBOW 90 DEG.
ADAPTER, STRAIGHT
ADAPTER, STRAIGHT
ADAPTER, STRAIGHT
ADAPTER, STRAIGHT
ADAPTER, ELBOW 90 DEG.
ADAPTER, STRAIGHT
ORIFICE, .063
ORIFICE, .070
ORIFICE. .055
SOLENOID LOCK VALVE ASY.
CAP, PLASTIC, OUTER
CAP PLASTIC.
ADAPTER, STRAIGHT
ADAPTER, ELBOW
MACHETE - M/B 17,21,24 (APR-04)
VALVE ASY - 5 SPOOL LOAD SENSE
MACHETE - M/B 17,21,24 (APR-04)
VALVE ASY - 5 SPOOL LOAD SENSE
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
02976688
02971378
63042700
02976632
02972113
02968850
02972177
02972179
02962213
02968850
02972209
02972210
02969398
02972208
02957416
02963637
02975438
02976531
02968399
02972178
-1
2
2
5
5
3
2
1
1
1
1
2
1
3
8
1
1
1
1
VALVE ASY, 5 SPOOL (LOAD SENSE)
VALVE, 5 SPOOL
ADAPTER, STRAIGHT
ADAPTER, ELBOW, 90 DEG.
ADAPTER, STRAIGHT
ADAPTER, STRAIGHT
ADAPTER, STRAIGHT
ADAPTER, STRAIGHT
ADAPTER, ELBOWM 90 DEG.
ADAPTER, STRAIGHT
ORIFICE, .063
ORIFICE, .070
ORIFICE, .055
SOLENOID LOCK VALVE ASY.
CAP, PLASTIC (OUTER)
CAP, PLASTIC (OUTER)
ADAPTER, STRAIGHT
ADAPTER, ELBOW
ORIFICE, .040
ADAPTER, ELBOW
MACHETE - M/B 17,21,24 (APR-04)
VALVE ASY - OPEN & CLOSED CENTER SYS.
MACHETE - M/B 17,21,24 (APR-04)
VALVE ASY - OPEN & CLOSED CENTER SYS.
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
02971378
02971379
02974004
02974005
02974027
02974838
02975950
02976024
02977032
02977414
02977745
02977851
02977957
02980656
02980657
02980658
02980659
02980660
02980661
02980662
02980663
02980664
02980665
--2
3
5
5
5
5
1
1
3
20
2
3
1
1
2
1
1
1
1
1
1
VALVE ASY, CCLS
VALVE ASY, OCFD
ELECTRIC MODULE, DOOR & TILT
ELECTRIC MODULE, SWING LIFT & DIPPER
SEAL KIT, MODULE TO VALVE SECTION
HANDLE MODULE
SEAL KIT, HANDLE TO VALVE SECTION
CONNECTOR GASKET
VALVE ASY KIT (W/ TIE BOLTS & SEAL)
RELIEF VALVE, 2755 PSI
RELIEF VALVE, 2030 PSI
BOLT
RELIEF VALVE
SECTION ASY, SWING, LIFT OR DIPPER
SECTION ASY, TILT
SECTION ASY, DOOR
SPOOL, SWING OR DOOR
SPOOL, LIFT
SPOOL, DIPPER
SPOOL TILT
SECTION, INLET (CCLS)
SECTION, INLET (OCFD)
SECTION, END CAP
20
MACHETE - M/B 17,21,24 (APR-04)
VALVE ASY - SOLENOID
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
02972208
02971425
02975198
02975199
-1
1
1
VALVE ASY SOLENOID
SEAL KIT, SOLENOID
COIL, SOLENOID
CARTRIDGE, VALVE
MACHETE - M/B 17,21,24 (APR-04)
CYL ASY, LIFT - P/N 02967173A
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
02968841
02967173A
02975466
02975452
02975457
02975552
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
02975453
* SEAL KIT
02968803
63149100
02968835
02968834
02975527
--1
1
1
1
1
1
3
2
1
1
1
2
1
1
2
2
1
LIFT CYL. ASY, W/ FITTINGS
LIFT CYL. ASY, L/ FITTINGS
TUBE / BARREL WLDMNT
CYL. HEAD
PISTON
ROD WLDMNT
O-RING, (IN ITEM 17)
SEAL ROD, HALITE, (IN ITEM 17)
SEAL, WIPER ROD, (IN ITEM 17)
SEAL, PISTON RING, (IN ITEM 17)
WEAR RING, (IN ITEM 17)
LOCKNUT
SEAL, (IN ITEM 17)
BUSHING
ELBOW
PLASTIC TIE, ORANGE / WHITE (ORW)
SEAL KIT (ITEMS 5,6,7,8,9, 10 & 12)
MACHETE - M/B 17,21,24 (APR-04)
CYL ASY, DIPPER - 17 FT - P/N 02979920
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
02979920
02979784
63149100
02968830
02968831
02968803
5JRC16140
002625
02978823
02979947
02979924
02975531
-1
1
1
1
2
1
1
1
1
1
1
DIPPER CYL ASY.
CYLINDER HEAD
ADAPTER, ELBOW
PLASTIC TIE - W/ BLUE TIE (B)
PLASTIC TIE - W/ BLUE / WHITE TIE (BW)
BUSHING
LOCKNUT
PISTON
ROD WLDMNT
CYLINDER HEAD
SEAL KIT
MACHETE - M/B 17,21,24 (APR-04)
CYL ASY, DIPPER - 21 & 24 FT. - P/N 02967174A
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
02968802
02967174A
02975553
02975452
02975457
02975552
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
02975453
02968803
* SEAL KIT
63149100
02968831
02968830
02975527
-1
1
1
1
1
1
3
2
1
1
1
2
1
1
2
2
1
DIPPER CYL. ASY, W/ FITTINGS
DIPPER CYL. ASY, L/ FITTINGS
CYL. HEAD
PISTON
ROD WLDMNT
LOCKNUT
BUSHING
SEAL, (IN ITEM 17)
ELBOW
PLASTIC TIE, BLUE / WHITE (BW)
SEAL KIT (ITEMS 5,6,7,8,9, 10 & 13)
MACHETE - M/B 17,21,24 (APR-04)
CYL ASY, SWING - P/N 02967172A
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
02968840
02967172A
02975463
02975450
02975454
02975459
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
5JRC16140
*SEAL KIT
63149100
02968833
02968832
02968803
02975530
--1
1
1
1
1
1
3
2
1
1
1
2
1
1
3
1
SWING CYL. ASY, W/ FITTINGS
SWING CYL. ASY, L/ FITTINGS
CYL. HEAD
PISTON
ROD WLDMNT
WEAR RING
LOCKNUT
SEAL, CYL. HEAD, (IN ITEM 16)
ELBOW
PLASTIC TIE, GREEN / WHITE (GW)
PLASTIC TIE, GREEN (G)
BUSHING
SEAL KIT (ITEMS 5,6,7,8,9 & 11)
MACHETE - M/B 17,21,24 (APR-04)
CYL ASY, TILT - P/N 02967175A
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
02968806
02967175A
02975539
02975450
02975454
02975540
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
02975453
*SEAL KIT
63149100
02968828
02968829
02968803
02975541
02975530
--1
1
1
1
1
1
3
2
1
1
1
2
1
1
2
2
1
TILT CYL. ASY, W/ FITTINGS
TILT CYL. ASY, L/ FITTINGS
CYL. HEAD
PISTON
ROD WLDMNT
LOCKNUT
SEAL, CYL. HEAD, (IN ITEM 17)
ELBOW
PLASTIC TIE, RED / WHITE (RW)
BUSHING
BUSHING
SEAL KIT (ITEMS 5,6,7,8,9 & 11)
MACHETE - M/B 17,21,24 (APR-04)
60 IN. ROTARY HEAD ASY. S/N MR60-02050 & DOWN
MACHETE - M/B 17,21,24 (APR-04)
60 IN. ROTARY HEAD ASY. S/N MR60-02050 & DOWN
ITEM
PART NO.
QTY.
DESCRIPTION
2
3
4
5
6
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
02968858
00011100
00015800
00007000
00755153
02970595
NFS
02971701
00023100
00756875
00759862
02767500
02976448
02885700
02885800
651102
02960018
02961480
02971720
02971756
02967775
02967782
02968836
02968837
02968856
02968873
02968874
02968875
02968876
02968877
02968878
02968894
02968895
02968896
02971702
3710151
99338S
165020
-46
24
12
2
1
1
1
11
1
2
1
1
2
1
1
2
1
1
1
1
1
1
3
REF
REF
1
1
1
1
1
1
1
1
1
2
1
1
ROTARY HEAD ASY, 60" W/ BAR CARRIER (NON-SALABLE)
FLATWASHER
LOCKNUT
BOLT
COTTER PIN
BOLT
SERIAL NUMBER PLATE
NUT, SLOTTED
BOLT
FLAP HOLD DOWN BAR
SHIELD, DEBRIS DEFLECTOR
HEX WRENCH, SPECIAL
PIN
REAR FLAP
REAR CLAMP BAR
PIN
ADAPTER, ELBOW
CYLINDER ASY
PIN WLDMNT
PIN
DOOR
ROD, HINGE
PLASTIC TIE, YELLOW (Y)
PLASTIC TIE, YELLOW / WHITE (YW)
ROTARY HEAD SUB-ASY, 60" (NON-SALABLE)
DECALS, (SEE SAFETY SECTION)
HOSE, (LARGE) - W/ RED TIE (R) PRESSURE HOSE
HOSE, (LARGE) - W/ ORANGE TIE (OR) RETURN HOSE
HOSE, (LARGE) - W/ BLUE TIE (B) CASE DRAIN
HOSE, (SMALL) - W/ YELLOW / WHITE (YW) DOOR CYL
HOSE, (SMALL) - W/ YELLOW TIE (Y) DOOR CYL
WASHER
METAL TACK
ROLL PIN
COTTER PIN
MACHETE - M/B 17,21,24 (APR-04)
60 IN. ROTARY HEAD ASY. S/N MR60-02051 & UP
MACHETE - M/B 17,21,24 (APR-04)
60 IN. ROTARY HEAD ASY. S/N MR60-02051 & UP
ITEM
PART NO.
QTY.
DESCRIPTION
2
3
4
5
6
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
48
02968858
00011100
00015800
00007000
00755153
02970595
02971500
02971701
00023100
00756875
00759862
02767500
02976448
02885700
02885800
651102
02960018
02961480
02971720
02971756
02971963
02967782
02968836
02968837
02968856
02968873
02968874
02968875
02968876
02968877
02968878
02968894
02968895
02968896
02971702
3710151
99338S
00010600
165020
-45
23
11
2
1
1
1
10
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
ROTARY HEAD ASY, 60" W/BAR CARRIER (NON-SALABLE)
FLATWASHER
LOCKNUT
BOLT
COTTER PIN
BOLT
PLATE, ALAMO S/N
NUT
BOLT
FLAP HOLD DOWN BAR
SHIELD, DEBRIS DEFLECTOR
HEX WRENCH, MODIFIED
PIN, 2-1/2" LONG
REAR FLAP, 10" HIGH X 63" LONG
REAR CLAMP BAR
PIN, 2" LONG
ADAPTER, ELBOW
CYLINDER ASY, DOOR
PIN, 9" LONG
DOOR WLDMNT
ROD, HINGE
PLASTIC TIE, YELLOW
PLASTIC TIE, YELLOW & WHITE
60" SQ. HD SUB-ASY.
DECAL KIT
HOSE, # 16 W/ RED PLASTIC TIE
HOSE, # 16 W/ ORANGE PLASTIC TIE
HOSE, # 16 W/ BLUE PLASTIC TIE
HOSE, # 4 W/ YELLOW & WHITE PLASTIC TIE
HOSE, # 4 W/ YELLOW PLASTIC TIE
PLASTIC TIE, RED
PLASTIC TIE, BLUE
PLASTIC TIE, ORANGE
WASHER, NARROW
METAL TACK
ROLL PIN
BOLT
COTTER PIN
MACHETE - M/B 17,21,24 (APR-04)
60 IN. ROTARY HEAD SUB-ASY. S/N MR60- 02050 & DOWN
MACHETE - M/B 17,21,24 (APR-04)
60 IN. ROTARY HEAD SUB-ASY. S/N MR60- 02050 & DOWN
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
13
14
15
16
17
18
19
20
21
22
23
24
25
26
29
31
32
32A
32B
32C
32D
33
34
02968858
00003901
00015800
00037200
00059700
02979020
03200269
02969230
02892100
02966899
02966900
02971928
02964861
5312316
15B600
W67
00019600
00750316
00750317
02891800
02958782
02961038
02967193B
02968859A
02978878
02970752
02979021
02972094
02971574
02981685
02981686
02981687
02981688
02979511
02977905
REF
4
14
16
14
8
8
1
8
2
1
1
4
16
14
16
4
2
2
4
1
1
1
1
1
4
16
1
1
1
1
1
2
1
1
ROTARY HEAD SUB-ASY, 60" (NON-SALABLE)
LOCKWASHER
LOCKNUT
LOCKNUT
BOLT
NUT
BOLT
BLADE BAR ASY.
BOLT
SKID SHOE
DECK HEAD
HITCH POST
BOLT, SOCKET HEAD
FLATWASHER, HARDENED SPECIAL
WASHER
WASHER
LOCKWASHER
HYDRAULIC FITTING ELBOW
SPLIT FLANGE KIT
HYDRAULIC FITTING, ELBOW
ADAPTER, HYD, STRAIGHT
GASKET, SPINDLE / MOTOR
MOTOR ASY
SPINDLE HOUSING
MOTOR PLATE
TIE ROD
NUT
SEAL KIT, VALVE BLOCK TO MOTOR
CARTRIDGE, RELIEF (4000 PSI)
O-RING
O-RING
O-RING
BACK-UP RING
GASKET, END COVER
MOTOR SEAL KIT
MACHETE - M/B 17,21,24 (APR-04)
60 IN. ROTARY HEAD SUB-ASY. S/N MR60-02051 & UP
MACHETE - M/B 17,21,24 (APR-04)
60 IN. ROTARY HEAD SUB-ASY. S/N MR60-02051 & UP
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
13
14
15
16
17
18
19
20
21
22
23
24
25
02968858
00003901
00015800
00037200
00059700
02980237
03200269
02969230
02892100
02966899
02966900
02971928
02964861
5312316
15B600
02980236
00019600
02980234
02980235
02891800
02980373
02961038
02979881
02968859A
00022200
REF
4
14
16
14
2
8
1
8
2
1
1
4
16
14
8
4
2
4
4
1
1
1
1
8
ROTARY HEAD ASY. W/ BAR CARRIER (NON SALABLE)
LOCKWASHER
LOCKNUT
LOCKNUT
BOLT
O-RING
BOLT
BLADR BAR ASY.
BOLT
SKID SHOE
DECK HEAD WLDMNT
HITCH POST WLDMNT
BOLT
WASHER, HARDENED
WASHER
BOLT
LOCKWASHER
ADAPTER, STRAIGHT
FLNAGE HALF
BOLT
ADAPTER, HYD.
GASKET, SPINDLE TO MOTOR
MOTOR ASY, PISTON TYPE
SPINDLE HOUSING, SPLINED
LOCKWASHER
MACHETE - M/B 17,21,24 (APR-04)
60 IN. ROTARY MOTOR ASY PARTS - P/N 02979881 S/N MR60-02051 & UP
MACHETE - M/B 17,21,24 (APR-04)
60 IN. ROTARY MOTOR ASY PARTS - P/N 02979881 S/N MR60-02051 & UP
ITEM
1
2
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
PART NO.
QTY.
DESCRIPTION
02979881
02980529
02980530
02980536
02980537
02980538
02980539
02980540
02980541
02980542
02980543
02980544
02980545
02980546
02980548
02980549
02980550
02980551
02980552
02980553
02980554
02980555
02980556
02980557
02980558
02980559
02980560
02980561
02980562
02980563
02980564
02980565
02980547
02980571
02980570
02980568
02980569
02980237
02980531
02980532
02980533
02980534
02980535
02980572
02980573
02980566
02980567
-1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
7
21
1
1
1
A/R
1
A/R
A/R
A/R
A/R
A/R
A/R
A/R
4
1
1
1
A/R
1
1
2
1
2
2
2
2
2
1
1
1
BARREL HOUSING ASY.
VALVE PLATE (IN ITEM 39)
NOZZLE
PLUG ASY, HEXAGON
BEARING HOUSING
O-RING (IN ITEM 39 & 40)
SEAL CARRIER
SHAFT SEAL (IN ITEM 39 & 40)
SPACER WASHER
RETAINING RING
RETAINING RING
SHAFT ASY.
CYLINDER BARREL (IN ITEM 39)
BARREL SUPPORT
PISTON ASY. (IN ITEM 39)
RISTON RING
RING GEAR
BEARING ASY, CUP & CONE
SPACER WASHER
RETAINING RING
SHIM, .020" (0.5)
SHIM, .007" (0.2)
SHIM, .015" (0.4)
SHIM, .023" (0.6)
SHIM, .030" (0.8)
SHIM, .039" (1.0)
SHIM, .027" (0.7)
BOLT, SOCKET HEAD
SAFETY VALVE
GUIDE PIN
RELIEF MANIFOLD
SEAL KIT, F/ RELIEF VALVE
RELIEF VALVE, 4061 PSI (280 BAR)
O-RING
FLAT KEY
BALL
PLUG, HEXAGON
O-RING
PLUG ASY.
PLUG ASY.
PLUG ASY.
REBUILD KIT (ITEMS 2,7,8,10,15 & 17)
SEAL KIT (ITEMS 7,8 &10)
MACHETE - M/B 17,21,24 (APR-04)
60 IN. ROTARY HEAD SPINDLE ASY P/N 02968859A
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
02968859
02967204
02967126
02967197
02967196
02909500
02909600
02967198
02959018
00003500
-1
1
1
1
2
1
1
1
1
SPINDLE ASY, F/ 60" ROTARY HEAD
SPINDLE SHAFT
SPINDLE HOUSING
LOWER BEARING ASY, CUP & CONE
UPPER BEARING ASY, CUP & CONE
NUT
TANG WASHER
SEAL
RELIEF PLUG
GREASE FITTING
MACHETE - M/B 17,21,24 (APR-04)
60 IN. DOOR CYL ASY - P/N 02961480A
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
02961480A
5JRC12160
33309
02975865
02975866
02975867
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
---------------02975528
-1
1
1
1
1
1
1
1
1
1
2-ref
1
DOOR CYLINDER ASY.
LOCKNUT
PISTON
ROD WLDMNT
TUBE / BARRELL WLDMNT
CYL HEAD
ROD WIPER SEAL (IN ITEM 12)
ROD SEAL (IN ITEM 12)
O-RING (IN ITEM 12)
SEAL (IN ITEM 12)
PISTON SEAL (IN ITEM 12)
O-RING F/ O-RING BOSS FITTING
SEAL KIT (ITEMS 6 THRU 10)
MACHETE - M/B 17,21,24 (APR-04)
60 IN. ROTARY BLADE BAR ASY. P/N 02969230
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
02969230
00020900
00023200
02969234
02761500
02971387
02969232
02969233
02969235
02969236
02782900
02957089
00003901
02964861
-2
2
4
1
1
1
1
2
2
2
2
REF
REF
BLADE BAR ASY
NUT
ROLL PIN
FLATWASHER
BLADE SET, MATCHED SET OF 2
BLADE BAR LEAF, TOP LEAF
BLADE BAR LEAF, MIDDLE LEAF
BLADE BAR LEAF, BOTTOM LEAF
BOLT, LONG BOLT
BOLT, SHORT BOLT
BLADE BOLT
LOCKWASHER
LOCKWASHER, 3/4" PL HEAVY
BOLT, SOCKET HEAD 3/4"-NC X 4" PL GR8
MACHETE - M/B 17,21,24 (APR-04)
50 IN. ROTARY HEAD ASY.
MACHETE - M/B 17,21,24 (APR-04)
50 IN. ROTARY HEAD ASY.
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
2A
3
4
5
6
7
8
9
10
11
12
13
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
02980202
02974664
02971928
02980205
02959390
00037200
02980204
02973438
02961480A
02976448
651102
5710121
5F5180
02974483
00755153
02975227
02975228
00753642
00011100
00015800
02960886
02957380
02957496
00023100
02035800
02964457
00003901
02886600
02960553B
02961038
02968836
02968837
02960018
02960882
02960883
02968878
02968877
02968894
02968895
02968896
02968874
02968875
02968876
00059700
00011400
02960885
00007000
-1
1
1
14
20
1
6
1
1
1
1
2
1
2
3
1
14
50
34
2
1
1
19
25
1
4
4
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
7
2
2
1
50" X-FRAME SQUARE HEAD ASY.
DECK WLDMNT, 50" SQ. HEAD
HITCH POST, 4 BAR
HITCH POST ADAPTER WLDMNT
BOLT
LOCKNUT
MOTOR & SPINDLE ASY
BOLT
CYLINDER ASY, DOOR
PIN, 5/8" X 2-1/2" DRILLED
PIN, DRILLED
COVER PLATE
WINGNUT
DOOR WLDMNT, 50" SQ HEAD
COTTER PIN
FLAP DEFLECTOR, DOOR
FLAP DEFLECTOR, DOOR
BOLT
FLATWASHER
LOCKNUT
FLAP DEFLECTOR, REAR
SIDE GUARD
REAR FLAP RETAINER
BOLT
WOOD WASHER
BLADE PAN ASY. COMPLETE
LOCKWASHER
BOLT, SOCKET HEAD
SPINDLE ASY.
GASKET
PLASTIC TIE, YELLOW (Y)
PLASTIC TIE, YELLOW / WHITE (YW)
ADAPTER, ELBOW
SKID SHOE, RH SIDE
SKID SHOE, LH SIDE
HOSE, 88" LONG
HOSE, 80" LONG
HOSE, 60" LONG - W/ RED TIE (R)
HOSE, 68" LONG - W/ ORANGE TIE (OR)
HOSE, 60" LONG - W/ BLUE TIE (B)
BOLT, FLAT SOCKET HEAD COUNTER SUNK HEAD
BOLT, HEX HEAD
RUBBER FLAP, 7-1/8" X 13-1/4"
BOLT
MACHETE - M/B 17,21,24 (APR-04)
50 IN. ROTARY MOTOR & SPINDLE ASY.
MACHETE - M/B 17,21,24 (APR-04)
50 IN. ROTARY MOTOR & SPINDLE ASY.
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
02980204
02979881
02960553B
02961038
02980235
02980234
02980237
02980373
02980236
00022200
02891800
00019600
-1
1
1
4
2
2
1
8
8
4
4
MOTOR & SPINDLE ASY. F/ 50" ROTARY HEAD
MOTOR ASY, PISTON TYPE MOTOR
SPINDLE ASY, SPLINED TYPE
GASKET, F/ MOTOR TO SPINDLE
FLANGE HALF
ADAPTER, STRAIGHT
O-RING
ADAPTER, STRAIGHT
BOLT
LOCKWASHER
BOLT
LOCKWASHER
MACHETE - M/B 17,21,24 (APR-04)
50 IN. ROTARY MOTOR ASY PARTS - P/N 02979881
MACHETE - M/B 17,21,24 (APR-04)
50 IN. ROTARY MOTOR ASY PARTS - P/N 02979881
ITEM
1
2
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
PART NO.
QTY.
DESCRIPTION
02979881
02980529
02980530
02980536
02980537
02980538
02980539
02980540
02980541
02980542
02980543
02980544
02980545
02980546
02980548
02980549
02980550
02980551
02980552
02980553
02980554
02980555
02980556
02980557
02980558
02980559
02980560
02980561
02980562
02980563
02980564
02980565
02980547
02980571
02980570
02980568
02980569
02980237
02980531
02980532
02980533
02980534
02980535
02980572
02980573
02980566
02980567
-1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
7
21
1
1
1
A/R
1
A/R
A/R
A/R
A/R
A/R
A/R
A/R
4
1
1
1
A/R
1
1
2
1
2
2
2
2
2
1
1
1
BARREL HOUSING ASY.
VALVE PLATE (IN ITEM 39)
NOZZLE
PLUG ASY, HEXAGON
BEARING HOUSING
SEAL CARRIER
SHAFT SEAL (IN ITEM 39 & 40)
SPACER WASHER
RETAINING RING
RETAINING RING
SHAFT ASY.
CYLINDER BARREL (IN ITEM 39)
BARREL SUPPORT
PISTON ASY. (IN ITEM 39)
RISTON RING
RING GEAR
SPACER WASHER
RETAINING RING
SHIM, .020" (0.5)
SHIM, .007" (0.2)
SHIM, .015" (0.4)
SHIM, .023" (0.6)
SHIM, .030" (0.8)
SHIM, .039" (1.0)
SHIM, .027" (0.7)
BOLT, SOCKET HEAD
SAFETY VALVE
GUIDE PIN
RELIEF MANIFOLD
SEAL KIT, F/ RELIEF VALVE
O-RING
FLAT KEY
BALL
PLUG, HEXAGON
O-RING
PLUG ASY.
PLUG ASY.
PLUG ASY.
REBUILD KIT (ITEMS 2,7,8,10,15 & 17)
SEAL KIT (ITEMS 7,8 &10)
MACHETE - M/B 17,21,24 (APR-04)
50 IN. DOOR CYL ASY - P/N 02961480A
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
02961480A
5JRC12160
33309
02975865
02975866
02975867
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
---------------02975528
-1
1
1
1
1
1
1
1
1
1
2-ref
1
DOOR CYLINDER ASY.
LOCKNUT
PISTON
ROD WLDMNT
TUBE / BARRELL WLDMNT
CYL HEAD
ROD WIPER SEAL (IN ITEM 12)
ROD SEAL (IN ITEM 12)
O-RING (IN ITEM 12)
SEAL (IN ITEM 12)
PISTON SEAL (IN ITEM 12)
O-RING F/ O-RING BOSS FITTING
SEAL KIT (ITEMS 6 THRU 10)
MACHETE - M/B 17,21,24 (APR-04)
50 IN. ROTARY BLADE PAN ASY - P/N 02964457
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
02964457
02964804
02962722
02964330
00755623
00023200
00020900
02030300
00748547
02964162
7A16824
00003901
02886600
02964954
02964161
02965229
-1
1
3
3
3
3
3
3
3
3
4
4
3
3
3
BLADE / SPIDER PAN ASY.
SPIDER PAN SUB-ASY (W/ ITEMS 7,8,9 & 10)
BLADE SET, MATCHED SET OF 3
BLADE BOLT
WASHER, SPECIAL ( HARDENED )
ROLL PIN
NUT, HEX SLOTTED HEAVY 1-1/8"-NF PL GR5
LOCKNUT, TOPLOCK 1"-NC PLB
FLATWASHER 1-1/32 X 2-3/16X.22
SPACER
BOLT, HEX HEAD 1"-NC X 3"PL GR5
LOCKWASHER, 3/4 PL HEAVY
BOLT, SOCKET HEAD 3/4"-NC X 2-1/2" PL GR8
KEY
BUSHING
SPACER
MACHETE - M/B 17,21,24 (APR-04)
50 IN. ROTARY SPINDLE ASY. P/N 02960553B
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
02960553B
02963815
02960561
02960558
02960559
00754627
02960557
00769938
02962030
02979570
00003500
-1
1
1
1
1
1
1
1
1
1
SPINDLE & HOUSING ASY
HOUSING
SPINDLE
BEARING RING
SEAL
SNAP RING
NUT
GREASE RELIEF FITTING
GREASE FITTING
MACHETE - M/B 17,21,24 (APR-04)
GRASS FLAIL ASY.
MACHETE - M/B 17,21,24 (APR-04)
GRASS FLAIL ASY.
ITEM
PART NO.
QTY.
DESCRIPTION
2
4
10
11
12
13
14
15
18
19
20
21
22
25
26
27
28
29
30
31
34
35
36
37
38
39
02972460
00015800
00695100
02090900
02775500
02845500
02957622
02969850
02962213
02968245
02969464
02969813
02972423
02969814
8301295
90.162.12
02971701
02971702
02971720
02971756
02970595
165020
02956851
02968894
02968895
02968896
02972373
-1
6
1
3
6
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
GRASS FLAIL HEAD ASY.
LOCKNUT
LOCKNUT
ADAPTER, ELBOW 90`
PLASTIC TIE, 21" LONG
BOLT
ADAPTER, STRAIGHT
SLEEVING, 100" LONG
ADAPTER, ELBOW 90`
CLAMP PLATE
ADAPTER, STRAIGHT
HOSE - W/ RED TIE (R)
HOSE - W/ BLUE TIE (B)
HOSE - W/ ORANGE TIE (OR)
FLAIL HEAD PRE-ASY.
NUT, SLOTTED
FLATWASHER
PIN
PIN, CHROME
BOLT
COTTER PIN
ADAPTER, ELBOW 90`
HITCH POST
MACHETE - M/B 17,21,24 (APR-04)
GRASS FLAIL SUB-ASY
MACHETE - M/B 17,21,24 (APR-04)
GRASS FLAIL SUB-ASY
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
76.114.01
05.201.17
05.264.21
05.264.23
05.264.24
02.281.03
05.281.04
05.282.01
05.282.03
05.286.01
05.286.03
05.287.02
05.839.24
09.589.01
09.590.01
09.594.02
09.595.02
41418.01
41424.01
41425.01
41429.01
41430.01
41436.01
41438.01
9293054
-2
3
10
6
5
6
12
20
16
17
6
6
1
1
2
1
2
1
1
1
1
2
1
12
FLAIL HEAD SUB-ASY, 1500 HEAD
TENSION PIN
SETSCREW
SETSCREW
SETSCREW
FLATWASHER, PLATED
FLATWASHER, PLATED
LOCKWASHER, PLATED
LOCKWASHER, PLATED
NUT, PLATED
NUT, PLATED
LOCKNUT
BOLT CUP SQUARE
GUARD, TOP DRIVE
GUARD, BOTTOM DRIVE
BACKING STRIP (1500)
GUARD, FLEXIBLE (1500)
CLAMP, GUARD
GUARD, FLEXIBLE (1500)
COWL, (1500)
GUARD, FRONT FIXED (1500)
GUARD, FRONT ADJUSTABLE (1500)
SPACER. PIVOT FRONT GUARD
PIN, PIVOT FRONT GUARD
BOLT CUP SQUARE
MACHETE - M/B 17,21,24 (APR-04)
GRASS FLAIL PULLEY ASY
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
76.154.01
03.795.02
04.282.17
05.281.03
05.282.03
05.286.03
05.424.02
05.424.18
05.625.12
05.299.53
05.960.16
09.587.01
41342.01
-2
2
2
4
4
1
1
2
3
1
1
1
PULLEY ASY, GRASS FLAIL 1500 HEAD
PULLEY
STUD
WASHER
SPRING WASHER
NUT
TAPER LOCK HUB, 1-1/8" BORE
TAPER LOCK HUB, 1-9/16" BORE
SCREW
BELT
KEY
PLATE, COVER
PLATE
MACHETE - M/B 17,21,24 (APR-04)
GRASS FLAIL CUTTERSHAFT ASY.
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
72.753.01
09.597.01
05.775.10
05.282.08
05.968.06
09.517.01
09.528.01
02975613
1
1
40
40
40
40
80
80
CUTTERSHAFT ASY, W/ KNIVES (1500 HEAD)
CUTTERSHAFT WLDMNT
BOLT
WASHER
LOCKNUT
SHACKLE
FLAIL KNIFE, SMOOTH STD.
FLAIL KNIFE, SERRATED OPT.
MACHETE - M/B 17,21,24 (APR-04)
GRASS FLAIL CUTTERSHAFT BEARING ASY
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
72.736.01
02.824.01
05.264.23
05.264.25
05.282.03
05.283.03
05.286.03
05.345.05
06.219.01
06.221.01
09.584.01
09.584.01
09.586.01
09.588.01
-2
10
4
12
2
10
4
2
2
1
1
1
1
BEAREING ASY, GRASS FLAIL 1500 HEAD
WASHER
SETSCREW
SETSCREW
SPRING WASHER
SHAKE PROOF WASHER
NUT
BOLT, SOCKET HEAD COUNTER SUNK
DISC, SHIELD
BEARING ASY.
BEARING PLATE, NON-DRIVE END
BOLT, ADJUSTING
BEARING PLATE, DRIVE END
GUARD, NON-DRIVE END
MACHETE - M/B 17,21,24 (APR-04)
GRASS FLAIL ROLLER ASY
ITEM
1
2
3
4
5
6
7
8
9
10
PART NO.
QTY.
DESCRIPTION
72.740.02
09.898.01
09.898.02
05.959.05
42954.01
04.164.04
04.394.01
05.953.01
05.234.01
05.264.23
05.282.03
42955.05
-1
1
4
2
2
2
4
2
2
2
1
ROLLER ASY, GRASS FLAIL 1500 HEAD (ITEMS 1 THRU 10)
BRACKET, LH (NOT SHOWN)
BRACKET, RH
CIRCLIP
BEARING
SEAL
CAP
GREASE FITTING
WASHER
BOLT, SOCKET HEAD
LOCKWASHER
ROLLER WLDMNT, (1500 HEAD)
MACHETE - M/B 17,21,24 (APR-04)
FLAIL AXE HEAD ASY. (ITEM 1 THRU 40)
MACHETE - M/B 17,21,24 (APR-04)
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
PART NO.
QTY.
DESCRIPTION
02970300
02973565
02956768
00001800
00002700
00011700
00013500
00015800
00019300
10119000
00023100
00023500
02027400
00035900
00037200
00752176
00753642
02716500
02892000
02918600
02956712
02956714
02956748
02957041
02965509
02957655M
02957655
02959935
02959839
02958131A
02958198
00750940
03200925
02967325
02967328
02970301
02976149
02970324
02970325
02970326
02970465
02970539
02970540
02970583
02970585
02970586
--2
11
15
4
3
4
8
2
4
6
4
4
4
1
2
8
7
6
1
1
1
2
1
1
1
1
1
2
1
2
1
2
1
1
1
1
1
1
1
3
1
4
1
2
FLAIL AXE HEAD ASY, W/ FLAIL AXE CUTTERSHAFT
FLAIL AXE HEAD ASY, W/ HD GRASS CUTTERSHAFT
ROLL PIN
NUT
FLATWASHER
LOCKWASHER
NUT
NUT
NUT
BOLT
NUT
FLATWASHER
BOLT
NUT
NUT
GREASE FITTING
NUT
NUT
BOLT
BOLT
RUBBER FLAP
CLAMP BAR
SKID SHOE, RH SIDE
ROLLER BEARING & FLANGE ASY
LOCKING COLLAR
CUTTERSHAFT W. KNIVES (FLAIL AXE)
CUTTER SHAFT WLDMNT (FLAIL AXE CUTTERSHAFT)
CUTTERSHAFT W/ KNIVES (HD GRASS)
CUTTER SHAFT WLDMNT (HD GRASS CUTTERSHAFT) NOT SHOWN
FLANGE BEARING ASY.
KEY
NUT
CARRIAGE BOLT
PULLEY
BUSHING
FLAIL AXE DECK WLDMNT
HITCH POST
PLATE, HITCH POST CLAMP
PLATE COVER, BELTS & PULLEY
DOOR HINGE ROD
DOOR WLDMNT
V-BELT
ROLLER
NUT
SKID SHOE, LH SIDE
WASHER
MACHETE - M/B 17,21,24 (APR-04)
MACHETE - M/B 17,21,24 (APR-04)
ITEM
PART NO.
QTY.
DESCRIPTION
41
42
43
44
45
46
47
48
02973256
02970709
02970710
02970725
02970763
03200521
23504500
02956949
102670
02958540
02956707
701431
100759
100761
02956943
02980976
000026
1
1
1
1
1
1
8
16
28
1
16
1
56
28
32
16
28
MOTOR MOUNT
PLATE, INSIDE
CYLINDER ASY.
HUB
MOTOR, PISTON TYPE
STEP KEY
NUT
BOLT, (FLAIL AXE CUTTER SHAFT)
PIN, HARDENED (HD GRASS CUTTERSHAFT) NOT SHOWN
BLADE KIT, 16 KNIVES (FLAIL AXE CUTTER SHAFT)
BLADE, (FLAIL AXE CUTTERSHAFT)
BLADE KIT, 56 KNIVES (HD GRASS CUTTER SHAFT) NOT SHOWN
BLADE, (HD GRASS CUTTERSHAFT) NOT SHOWN
RING, (HD GRASS CUTTERSHAFT) NOT SHOWN
BUSHING, F/ FLAIL AXE CUTTER SHAFT
LOCKNUT, (FLAIL AXE CUTTERSHAFT)
COTTER PIN (HD GRASS CUTTERSHAFT) NOT SHOWN
49
50
51
MACHETE - M/B 17,21,24 (APR-04)
FLAIL AXE DOOR CYLINDER ASY. - P/N 02970710A
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
02970710A
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
* SEAL KIT
02975588
5JRC8200
02975590
02975591
02975589
02975532
-3
2
1
1
1
1
1
1
1
1
1
1
1
CYLINDER ASY, FLAIL AXE DOOR CYL.
BACK-UP RING
O-RING
O-RING
LOCKWIRE
O-RING
BACK-UP RING
ROD WIPER
TUBE
LOCKNUT
PISTON
ROD
HEAD GLAND
SEAL KIT, (ITEMS 1 THRU 7)
MACHETE - M/B 17,21,24 (APR-04)
FLAIL AXE HEAD HOSE CONNECTIONS
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
02968874
02837800
02969464
02969564
02968895
02968896
02968894
1
1
1
1
2-REF
2-REF
2-REF
HOSE, LARGE, (W/ RED TIE)
HOSE, MEDIUM (W/ BLUE TIE)
ADAPTER, LARGE TO MEDIUM
HOSE, LARGE, (W/ ORANGE TIE)
PLASTIC TIE, BLUE (B) F/ ITEM 2
PLASTIC TIE, ORANGE (OR) F/ ITEM 4
PLASTIC TIE, RED (R) F/ ITEM 1
MACHETE - M/B 17,21,24 (APR-04)
FML 100H FLAIL HEAD ASY - (ITEM 1 THRU 50)
MACHETE - M/B 17,21,24 (APR-04)
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
04000100
02968212
02968217
02967335
02968899
02974250
02974249
02970948
02967517
02967522
02974087
02967513
02969746
02969079
02966998
02974196
02968908
02970104
00753230
02971322
02967530
02967541
00762394
02970077
02970051
02970110
02972845
02972854
02960143
02972853
02972852
02970877
02970108
02970108
02972851
02970107
02967462
02962850
02962855
02967461
02967532
00753864
00756026
02972465
02970184
02970069
700219C
00768990
02970071
00001200
00001300
-1
1
1
1
1
1
1
1
1
1
1
1
4
16
2
4
4
6
8
2
2
4
1
6
1
1
1
1
2
2
12
1
1
1
1
1
1
1
1
12
2
4
2
2
2
2
7
4
6
8
FLAIL HEAD ASY, FML100H
HOOD, COWLING
SHIELD DOOR
HITCH POST
CUTTERSHAFT
PULLEY, UPPER
PULLEY, LOWER
PULLEY LOCK, UPPER
PULLEY LOCK, LOWER
BELT GUARD
CYLINDER ASY, DOOR
BOTTOM PLATE
RUBBER FLAP
V-BELT
KNIFE
PIN, CYL. LINK
ROD, CUTTER BAR
BOLT
BOLT
BOLT
LOCKING TAB
BOLT
BOLT
NUT
WASHER
BOLT
GREASE TUBE
SPACER
ADAPTER
RING SUPPORT
BEARING SUPPORT
BOLT
SEAL
SEAL
BEARING, DRIVE END
BEARING, NON DRIVE END
RETAINING RING
SEAL
GUARD, ROTOR END
COVER, BEARING
BOLT
GREASE NIPPLE
BOLT
CUTTERSHAFT GUARD, UPPER HALF
CUTTERSHAFT GUARD, LOWER HALF
WASHER
NUT
WASHER
BOLT
NUT
LOCKWASHER
MACHETE - M/B 17,21,24 (APR-04)
MACHETE - M/B 17,21,24 (APR-04)
ITEM
PART NO.
QTY.
DESCRIPTION
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
00037200
02892000
02963645
00696800
02837800
02957622
02968874
02968894
02968895
02968896
02969463
02969464
02969661
8301295
02970078
02970079
02968223
02974088
02967565
02974472
02970048
02970101
02970060
02970061
02970062
02970065
02970101
02970050
00015800
02970595
02971756
02971720
165020
02971701
02971702
02973221
02973222
02972846
00768990
00756830
02972854
6
8
6
1
1
2
1
3
3
3
1
1
1
1
4
4
1
1
2
2
2
2
2
4
2
2
1
2
1
1
1
1
1
1
1
1
1
6
18
6
1
NUT
BOLT
BOLT
ADAPTER
HOSE, CASE DRAIN - W/ BLUE TIE (B)
ADAPTER
HOSE, PRESSURE - W/ RED TIE (R)
HOSE, RETURN - W/ ORANGE TIE (OR)
ADAPTER
SPINDLE ASY.
MOTOR ASY.
BOLT
LOCKWASHER
ROD, THREADED
DOUBLE ACTING, CLOSING VALVE
HOSE
QUICK COUPLER
WASHER
SETSCREW
BANJO BOLT
WASHER
ADAPTER
GREASE FITTING
SETSCREW
BANJO BOLT
NUT
BOLT, HEX HEAD
PIN
PIN WLDMNT
COTTER PIN
NUT, SLOTTED
FLATWASHER
SKID SHOE, RH
SKID SHOE, LH
BOLT
WASHER
NUT
SPACER RING
MACHETE - M/B 17,21,24 (APR-04)
FML 100H SPINDLE ASY. - P/N 02969661
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
02969661
02969659
02969660
00748537
5810381
5810310
00755628
02964269
02962030
02959018
00565000
-1
1
1
1
1
1
1
1
1
1
SPINDLE ASY, F/ FML 100H FLAIL HEAD
HOUSING
SPINDLE
BEARING CUP
BEARING CONE
SEAL
LOCKWASHER
LOCKNUT, BEARING ADJUSTING NUT
FITTING, RELIEF
PLUG
MACHETE - M/B 17,21,24 (APR-04)
DITCHER HEAD ASY
MACHETE - M/B 17,21,24 (APR-04)
DITCHER HEAD ASY
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
02973313
00001300
00001800
00002701
00015800
00037200
02973583
02873900
02875301
02881000
02891800
02957416
02961319
02963576
02963637
02970595
02973327
02973328
02973329
02973330
-6
4
2
2
4
1
1
1
4
6
2
2
4
4
2
1
1
1
A/R
02977703
A/R
02974163
02974161
02974162
02980913
02973336
02973522
02973563
02027400
002021
02973588
61026400
02956851
02973587
02969464
02962749
02977622
02980373
00770346
02980686
A/R
A/R
A/R
1
1
1
2
4
1
1
1
1
1
1
1
2
2
1
1
DITCHER HEAD ASY
LOCKWASHER
LOCKNUT
FLATWASHER
LOCKNUT
LOCKNUT
SPACER PLATE
HOUSING ASY.
BLADE HEAD ASY.
BOLT
BOLT
PLASTIC CAP, OUTER 1/4" (NOT SHOWN)
PLASTIC PLUG, INNER 3/8" (NOT SHOWN)
PLUG, (NOT SHOWN)
PLASTIC CAP, OUTER 3/8" (NOT SHOWN)
BOLT
DITCHER MOUNT
PIN, 1-1/4" DIA.
PIN, 1-1/2" DIA
MOTOR, (FEB. 2004 & DOWN) 11.9 CID (MOTOR LENGTH 10-5/8" LONG FROM
MOUNT FLANGE TO END OF MOTOR)
MOTOR (MAR. 2004 & UP) 7.95 CID (MOTOR LENGTH MEASURES 8-5/8"
FROM MOUNT FLANGE TO END OF MOTOR, THIS MOTOR WILL REPLACE
P/N 02973330 AS AN ASSEMBLY)
SEAL KIT, FRONT & REAR HALF COMPLETE (F/ MOTOR P/N 02973330 ONLY)
SEAL KIT, FRONT HALF ONLY (F/ MOTOR
SEAL KIT, REAR HLAF ONLY (F/ MOTOR P/N 02973330 ONLY)
MOTOR INPUT SHAFT (F/ MOTOR P/N 02973330 ONLY)
SPINDLE ASY
SWING BAR, (NOT SHOWN)
CAP NUT, (NOT SHOWN)
BOLT
HOSE
HOSE
HOSE
ADAPTER, ELBOW 90`
ADAPTER, STRAIGHT
ADAPTER, STRAIGHT
ADAPTER, ELBOW 45`
ADAPTER, STRAIGHT (USED W/ MOTOR P/N 02973330)
ADAPTER, STRAIGHT (USED W/ MOTOR P/N 02977703)
ADAPTER, STRAIGHT
LOW PRESSURE RELIEF
20
21
22
23
24
25
26
27
28
29
30
31
32
33
MACHETE - M/B 17,21,24 (APR-04)
DITCHER HOUSING ASY
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
02873900
02974000
02874601
02875001
00002700
00026200
02875101
02886900
00001300
00001200
02811000
02276700
37107B13
02959086
02959087
12621000
00023100
00059700
00012101
00013901
02959089
00011100
02042500
000644
-1
1
1
2
2
2
4
4
4
1
2
4
3
3
3
1
2
14
14
1
3
2
8
DITCHER HOUSING ASY.
HOUSING WLDMNT
DEFLECTOR
HINGE PIN
FLATWASHER
COTTER PIN
BACK-UP PLATE
BOLT
LOCKWASHER
NUT
CYLINDER ASY.
CYL. PIN
HAIR PIN CLIP
RUBBER DEFLECTOR
DEFLECTOR CLAMP BAR
BOLT
BOLT
BOLT
LOCKWASHER
NUT
HOUSING COVER
FLATWASHER
ADAPTER, STRAIGHT
BOLT
MACHETE - M/B 17,21,24 (APR-04)
DITCHER SPINDLE ASY.
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
02973336
02883700
02708100
02907700
02707600
02872701
02873200
02870900
00003500
02873301
02959017
02973318
02873800
02959014
02959018
-1
2-REF
2
3
1
1
1
1-REF
1
1
1
1
1
1
SPINDLE ASY (ITEMS 1 THRU 14)
SPINDLE HSG W/ BRG CUPS & GREASE FITTING
BEARING CUP
BEARING CONE
SEAL
SPINDLE SHAFT
SPACER
NUT
GREASE FITTING
COUPLING HALF, SPINDLE
KEY
COUPLING HALF, MOTOR
CHAIN COUPLING
SETSCREW
RELIEF FITTING
MACHETE - M/B 17,21,24 (APR-04)
DITCHER BLADE CARRIER ASY.
ITEM
1
2
3
5
6
7
8
9
10
11
PART NO.
QTY.
DESCRIPTION
02875301
02875400
02875900
02886900
00001800
02958680
02958675
02958685
02891800
02958684
00003901
00037200
-1
3
6
18
3
3
A/R
12
6
6
6
BLADE HEAD ASY W/ BLADES (FORWARD ROTATION)
BLADE HEAD WLDMNT
WEAR PLATE
BOLT
NUT
MOUNT BRACKET
BLADE, ROUGH CUT
SHIM KIT FOR ROUGH CUT BLADES
BOLT
BOLT
LOCKWASHER
NUT
MACHETE - M/B 17,21,24 (APR-04)
BUZZ BAR HEAD ASY - 90 INCH - S/N 01306 (10-01) & DOWN
MACHETE - M/B 17,21,24 (APR-04)
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
52
53
54
55
56
57
58
59
60
PART NO.
QTY.
DESCRIPTION
02974203
02974237
02974238
02974235
02974659
02974658
02976017
00001200
02974209
02978273
02979295
02974225
00750614
002521
02974241
02974239
02974240
02978265
02975441
02975440
02975439
00011400
00011100
00001800
02978249
8301295
00749130
02978267
02978268
02978269
02978270
02978264
02976149
00037200
02970324
02918600
02974215
00015800
00023100
02974207
02974212
02975600
02968894
02957622
02968896
02970466
02975437
02969678
02969464
02972981
02975438
02962213
02158800
00696800
02971720
02971702
02971701
165020
02970595
02971756
02669600
02975964
-4
2
3
8
8
16
6
A/R
A/R
A/R
3
16
3
3
4
4
1
7
7
7
1
10
6
1
1
8
1
1
1
1
1
1
6
1
6
1
9
8
1
1
A/R
1
2
1
2
1
1
3
1
1
1
1
1
1
1
1
1
1
1
5
1
BUZZ BAR HEAD ASY, 90 INCH 4 BLADE
END CAP
BLADE SPACER
HUB ASY
BOLT, SOCKET HEAD CNTR-SNK 1/2"NC X 3-1/2" W/HOLE
BOLT, SOCKET HEAD CNTR-SNK 1/2"NC X 2" W/HOLE
NUT, SLOTTED
NUT, HEX 1/2"-NC
SAW BLADE BODY WLDMNT, USED 01/99 TO 12/01
SAW BLADE BODY WLDMNT, USED 01/02 TO 07/02
SAW BLADE BODY WLDMNT, USED 08/02 TO CURRENT
TENSION ADJUSTING BRACKET
NUT
BOLT
V-BELT
SHEAVE
QD BUSHING
BELT COVER, LONG
STUD, QUICK RELEASE
RETAINER, QUICK RELEASE
RECEIVER, QUICK RELEASE
BOLT
FLATWASHER
LOCKNUT
PLATE, MOTOR MOUNT
BOLT
HUB
INSERT, URETHANE
COVER, NYLON
HUB
BELT COVER, SHORT
HITCH POST
LOCKNUT
CLAMP
BOLT
HITCH TUBE WLDMNT
LOCKNUT
BOLT
BUMPER
REAR SHIELD WLDMNT
SAW BLADE PACK (2 PK SHIPPED UNMOUNTED)
PLASTIC TIE, RED (RED)
ADAPTER, HYD, STGHT
PLASTIC TIE 11" LG (ORANGE)
ADAPTER, HYD, TEE
HOSE #16-16FJX -16FJX45- 74LG
HOSE #16-16FJX -16FJX45- 74LG
ADAPTER, HYD, REDUCER
HOSE #8 - 8FJX - 8FJX - 80LG
ADP HYD STGHT 8MB - 8FJX
ADAPTER, HYD, ELBOW
HOSE #8 - 8FJX - 8FJX - 17LG
ADAPTER, HYD, STGHT
WELDMENT, PIN - 11-1/2LG
FLATWASHER, 1-3/8" TYPE B NARROW
NUT SLOT TED 1-3/8"-12NF PLB
COTTER PIN 5/16" X 2-1/2" PL
BOLT, HEX HEAD 3/8"-NC X 2-3/4" PL GR8
PIN, 1-1/2" X 9" CHROME
KEY, 1/4" SQ KEY 1-1/4" LG.
RELIEF MANIFOLD ASY, 2900 PSI
MACHETE - M/B 17,21,24 (APR-04)
MACHETE - M/B 17,21,24 (APR-04)
ITEM
PART NO.
QTY.
DESCRIPTION
61
62
63
64
65
66
67
68
02919600
02968895
40010000
63000500
02978255
02978256
02978272
02978372
2
1
16
16
1
1
2
4
CAP-NUT #4FJ
PLASTIC TIE, 11" LG
COTTER PIN, 1/8" X 1"
WASHER, PLATED
MOTOR MNT WELDMENT, MACHINED
SHIELD, MOTOR
STAINLESS STEEL SOCKET BUTTON
BOLT, SHSS M10XP1.5 X 10MM LG
MACHETE - M/B 17,21,24 (APR-04)
BUZZ BAR HEAD ASY - 90 INCH - S/N 01307 (11-01) & UP
MACHETE - M/B 17,21,24 (APR-04)
ITEM
PART NO.
QTY 90in
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
02974203
02974237
02974238
02974235
02974659
02974658
02976017
00001200
02979295
02974225
00750614
002521
02974241
02974239
02974240
02979297
02975441
02975440
02975439
00011400
00011100
00001800
02978249
8301295
00749130
02978267
02978268
02978269
02978270
02979296
02976149
00037200
02970324
02918600
02974215
00015800
00023100
02974207
02974212
02975600
02968894
02957622
02968896
02970466
02975437
02969678
02969464
02972981
02975438
02962213
02158800
00758194
00769736
00769737
02925100
02958241
02962764
00756004
02965262
02967827
00757139
02974998
1
4
2
3
8
8
16
6
1
3
16
3
3
4
4
1
9
9
9
1
10
6
1
1
8
1
1
1
1
1
1
6
1
6
1
9
8
1
1
A/R
1
2
1
2
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
SAW HEAD ASY, 4 BLADE 90 IN.
END CAP
BLADE SPACER
SPINDLE HUB ASY.
BOLT, SOCKET HEAD COUNTERSUNK 1/2"-NC X 3-1/2" W/HOLE
BOLT, SOCKET HEAD COUNTERSUNK 1/2"-NC X 2" W/HOLE
NUT, SLOTTED 1/2"-NC PLB
NUT, HEX 1/2"-NC PL
SAW BODY WELDMENT, 4 BLADE
TENSION ADJUSTMENT BRACKET
NUT, 1/2"-20NF - 90 DEG.CONE LUG PL
BOLT, HEX HEAD1/2"-NC X 3-1/2" PL GR5
BELT, POLY-V
SHEAVE, PULLEY
BUSHING, QD
SHEET, BELT COVER, LEFT 4 BLADE
STUD, QUICK RELEASE W/RING
RETAINER F/ QUICK RELEASE
RECEIVER F/ QUICK RELEASE
BOLT, HEX HEAD 3/8"-NC X 1" PL GR5
FLATWASHER, 3/8" PL STD
LOCKNUT, TOPLOCK 1/2"-NC PLB
DRIVE SPINDLE ASY
MOTOR, PISTON - 2.48 CU.IN./REV
BOLT, HEX HEAD 1/2"-13NC X 1-3/4" PL GR5
HUB, 1-1/8" BORE 1/4" KEY
INSERT, URETHANE
COVER, PROTECTIVE NYLON
HUB, 1-1/8" BORE 5/16" KEY
SHEET, BELT COVER SHORT
HITCH POST WELDMENT
LOCKNUT, TOPLOCK 3/4"-NC PLC
BOLT, HEX HEAD 3/4"-10NC X 2" PL GR8
HITCH TUBE WELDMENT, 4 BLADE
BUMPER
SHIELD WELDMENT, REAR 4 BLADE
SAW BLADE SET, SET OF 2 BLADES
PLASTIC TIE. 11" LG
ADAPTER, HYD STRAIGHT
PLASTIC TIE, 11" LG
ADAPTER, HYD TEE
HOSE, #16 - 16FJX - 16FJX45 - 74" LG ORANGE TIE
HOSE, #16 - 16FJX - 16FJX45 - 74" LG RED TIE
ADAPTER, HYD, REDUCER
HOSE, #8 - 8FJX - 8FJX - 80" LG BLUE TIE
ADAPTER, HYD STRAIGHT 8MB - 8FJX
ADAPTER, HYD ELBOW
HOSE, #8 - 8FJX - 8FJX - 17" LG
DECAL, WARNING BELT SHIELD
DECAL, USE/REPAIR GUARDS
DECAL, BLADES THROWN OBJECTS
DECAL, REPLACEMENT PARTS
DECAL, TRACTOR OPERATOR SAFETY
DECAL, PINCH POINTS
DECAL, SHIELD MISSING
DECAL, WARNING HOSE BURST
DECAL, MULTI HAZZARD
DECAL, ALAMO GROUP
DECAL, BUZZBAR
MACHETE - M/B 17,21,24 (APR-04)
MACHETE - M/B 17,21,24 (APR-04)
ITEM
PART NO.
QTY 90in
DESCRIPTION
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
D138
02975158
02975170
02975515
02975516
02975514
02975513
3710151
02979546
1458392
1458393
00696800
02971720
02971702
02971701
165020
02970595
02971756
02669600
02961134
02975928
02975964
02919600
02968895
40010000
63000500
02979262
02979546
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
5
1
1
1
2
1
16
16
1
1
DECAL, BLADE ROTATION
DECAL, HEAR PROTECTION REQD
DECAL, ROTATING BLADES
DECAL, WARNING DISCONNECT
DECAL, NO HITCH POST HERE
DECAL, PITCH ADJUSTMENT
PLATE, SERIAL NUMBER BB90
METAL, TACK
DECAL,, ALAMO IND. GREEN & BLACK
DECAL, RED REFLECTOR
DECAL, YELLOW REFLECTOR
PIN WELDMENT, 11-1/2" LG
FLATWASHER,1-3/8" TYPE B NARROW
NUT, SLOTTED 1-3/8"-12NF PLB
COTTER PIN, 5/16" X 2-1/2" PL
KEY, 1/4" SQ KEY 1 1/4" LG.
DECAL, PATENT PENDING
INSERT SHEET, BUZZBAR MACHETE
CAPNUT, # 4FJ
PLASTIC TIE, 11" LG
COTTER PIN, 1/8" X 1"
WASHER, PLATED
MOTOR MOUNT TUBE, MACHINED
DECAL, ALAMO IND. GREEN & BLACK
MACHETE - M/B 17,21,24 (APR-04)
MACHETE - M/B 17,21,24 (APR-04)
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
02979249
02974237
02974238
02974235
02974659
02974658
02976017
00001200
02979253
02974225
00750614
002521
02974241
02974239
02974240
02979255
02975441
02975440
02975439
00011400
00011100
00001800
02978249
8301295
00749130
02978267
02978268
02978269
02978270
02979296
02976149
00037200
02970324
02918600
02979256
00015800
00023100
02974207
02979258
02975600
02968894
02957622
02968896
02970466
02975437
02969678
02969464
02972981
02975438
02962213
02158800
00758194
00769736
00769737
02925100
02958241
02962764
00756004
02965262
02967827
02960766
02974998
-4
2
3
4
8
12
6
1
3
16
3
3
3
3
1
9
9
9
1
10
6
1
1
8
1
1
1
1
1
1
6
1
6
1
9
8
1
1
A/R
1
2
1
2
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
SAW BLADE HEAD ASY, 69" (3 BLADE)
END CAP
BLADE SPACER
SPINDLE ASY.
BOLT, SOCKET CNTR-SNK 1/2"-NC X 3-1/2" W/HOLE
BOLT, SOCKET CNTR-SNK 1/2"-NC X 2" W/HOLE
NUT, HEX 1/2"-NC PL
TENSION ADJUSTMENT BRACKET
NUT, 1/2"-20NF 90DEG CONE LUG PL
V-BELT
SHEAVE W/GROOVE
BUSHING, QD
SHEET, BELT COVER, LEFT 3 BLADE
RETAINER F/QUICK RELEASE
BOLT, HEX HEAD 3/8"-NC X 1 PL GR5
DRIVE SPINDLE ASY.
MOTOR, PISTON-2.48 CU.IN./REV
HUB, 1-1/8" BORE X 1/4" KEY
INSERT, URETHANE
HUB, 1-1/8" BORE X 5/16" KEY
BELT COVER, SHORT
HITCH POST WELDMENT
HITCH TUBE WELDMENT, 3 BLADE
BUMPER
SHIELD WELDMENT, REAR
SAW BLADE PACKAGE OF 2
PLASTIC TIE, 11" LG
PLASTIC TIE, 11" LG
ADAPTER, HYD TEE
HOSE, #16 - 16FJX - 16FJX45 - 74" LG (ORANGE TIE)
HOSE, #16 - 16FJX - 16FJX45 - 74" LG (RED TIE)
ADAPTER, HYD REDUCER
HOSE, #8 - 8FJX - 8FJX - 80" LG (BLUE TIE)
ADAPTER, HYD ELBOW
HOSE, #8 - 8FJX - 8FJX - 17" LG
DECAL, REPLACE PARTS
DECAL, PINCH POINTS
DECAL-MULTI HAZ
DECAL, ALAMO INDUSTRIAL LOGO
DECAL, BUZZBAR
MACHETE - M/B 17,21,24 (APR-04)
MACHETE - M/B 17,21,24 (APR-04)
ITEM
PART NO.
QTY.
DESCRIPTION
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
D138
02975158
02975170
02975515
02975516
02975514
---NFS-------NFS----02979546
1458392
1458393
00696800
02971720
02971702
02971701
165020
02970595
02971756
02669600
02961134
02975928
02975964
02919600
02968895
40010000
63000500
02979262
02979546
1
1
1
1
1
1
REF
REF
1
1
1
1
1
1
1
1
1
1
4
1
1
1
2
1
12
12
1
1
DECAL, BLADE ROTATION
SERIAL NUMBER PLATE BB90
METAL TACK
DECAL, YELLOW REFLECTOR
NUT, SLOTTED 1-3/8"-12NF PLB
KEY, 1/4" SQ KEY 1-1/4" LG.
CAP - NUT # 4FJ
PLASTIC TIE, 11" LG
COTTER PIN 1/8" X 1"
WASHER, PLATED
MACHETE - M/B 17,21,24 (APR-04)
MACHETE - M/B 17,21,24 (APR-04)
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
02979265
02974237
02974238
02974235
02974659
02974658
02976017
00001200
02979269
02974225
00750614
002521
02974241
02974239
02974240
02979271
02975441
02975440
02975439
00011400
00011100
00001800
02978249
8301295
00749130
02978267
02978268
02978269
02978270
02979296
02976149
00037200
02970324
02918600
02979272
00015800
00023100
02974207
02979274
02975600
02968894
02957622
02968896
02970466
02975437
02969678
02969464
02972981
02975438
02962213
02158800
00758194
00769736
00769737
02925100
02958241
02962764
00756004
02965262
02967827
02960766
02974998
-4
2
3
4
8
8
6
1
3
16
3
3
2
2
1
9
9
9
1
10
6
1
1
8
1
1
1
1
1
1
6
1
6
1
9
8
1
1
A/R
1
2
1
2
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
SAW HEAD ASY, 48 INCH 2 BLADE
END CAP
BLADE SPACER
SPINDLE ASY.
BOLT, SOCKET HEAD CNTR-SNK 1/2"-NC X 3-1/2"
BOLT, SOCKET HEAD CNTR-SNK 1/2"-NC X 2"
NUT, HEX 1/2"-NC PL
BRACKET TENSION ADJUSTMENT
NUT, 1/2"-20NF 90DEG.CONE LUG PL
V-BELT
SHEAVE, W/GROOVE
BUSHING QD
BELT COVER, LEFT 2
RETAINER F/ QUICK RELEASE
BOLT, HEX HEAD 3/8"-NC X 1" PL GR5
DRIVE SPINDLE ASY
MOTOR, PISTON-2.48 CU.IN./REV
HUB, 1-1/8" BORE & 1/4" KEY
INSERT, URETHANE
HUB, 1-1/8" BORE & 5/16" KEY
SHEET, BELT COVER SHORT
HITCH POST WELDMENT
HITCH POST CLAMP PLATE
MOUNT TUBE WELDMENT, 2 BLADE
BUMPER
REAR SHIELD WELDMENT,
SAW BLADE PACKAGE OF 2
PLASTIC TIE, 11" LG (RED TIE)
PLASTIC TIE, 11" LG(ORANGE TIE)
ADAPTER, HYD, TEE
HOSE, #16 - 16FJX - 16FJX45 - 74" LG (RED TIE)
HOSE, #16 - 16FJX - 16FJX45 - 74" LG (ORANGE TIE)
ADAPTER, HYD REDUCER
HOSE, #8 - 8FJX - 8FJX - 80" LG (BLUE TIE)
ADAPTER, HYD ELBOW
HOSE, #8 - 8FJX - 8FJX - 17" LG
DECAL, REPLACEMENT PARTS
DECAL, PINCH POINTS
DECAL, MULTI HAZ
DECAL, ALAMO INDUSTRIAL LOGO
DECAL, BUZZBAR
MACHETE - M/B 17,21,24 (APR-04)
MACHETE - M/B 17,21,24 (APR-04)
ITEM
PART NO.
QTY.
DESCRIPTION
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
D138
02975158
02975170
02975515
02975516
02975514
---NFS-------NFS----02979546
1458392
1458393
00696800
02971720
02971702
02971701
165020
02970595
02971756
02669600
02961134
02975928
02975964
02919600
02968895
40010000
63000500
02979262
02979546
1
1
1
1
1
1
REF
REF
1
1
1
1
1
1
1
1
1
1
3
1
1
1
2
1
8
8
1
1
DECAL, CW BLADE ROTATION
PLATE, SERIAL NUMBER BB90
METAL TACK
DECAL, ALAMO IND. GREEN &BLACK
DECAL,Y ELLOW REFLECTOR
NUT, SLOT TED 1-3/8"-12NF PLB
PIN, CHROME 1-1/2" X 9"
KEY, 1/4" X 1/4" X 1-1/4" LG
CAP-NUT, #4FJ
PLASTIC TIE 11" LG
COTTER PIN 1/8" X 1"
WASHER, PLATED
DECAL, ALAMO IND. GREEN &BLACK
MACHETE - M/B 17,21,24 (APR-04)
BUZZ BAR SPINDLE ASY - S/N BB-01219
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
PART NO.
QTY.
DESCRIPTION
02978249
02974235
02974224
02978472
02978257
02974234
70044
5312314
15C2000
5D20120
00766549
00003500
02959018
00752177
00606000
1
A/R
1
A/R
1
1-A/R
2-A/R
2-A/R
1-AR
1-A/R
2-AR
1-A/R
1-A/R
4-A/R
1-A/R
SPINDLE ASY, DRIVE SPINDLE (SHOWN)
SPINDLE ASY, NON-DRIVE (NOT SHOWN)
SPINDLE HOUSING, MACHINED
SPINDLE SHAFT, NON-DRIVE SPINDLE
SPINDLE SHAFT, DRIVE SPINDLE
COLLAR, BEARING PRELOAD
BEARING CUP, UPPER OR LOWER
BEARING CONE, UPPER OR LOWER
WASHER, 1-1/4" HARDEND
NUT, HEX SLOTTED 1-1/4"-12NF PL
SEAL, UPPER OR LOWER
GREASE FITTING, 1/8" STRAIGHT
GREASE RELIEF FITTING, 1-5LBS
BOLT, STUD 1/2"-20NF X 1-7/8"
COTTER PIN, 3/16 X 2
Qty shown is per spindle assembly, qty will depend on number of spindles you are repairing. Check model before
ordering parts.
MACHETE - M/B 17,21,24 (APR-04)
TIMBERCAT HEAD ASY (ITEMS 1 THRU 39)
MACHETE - M/B 17,21,24 (APR-04)
TIMBERCAT HEAD ASY (ITEMS 1 THRU 39)
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
PART NO.
QTY.
DESCRIPTION
02972149
02972150
02971390
02971392
02971389
02971391
02971398
02971399
02972363
02972512
00751581
02960521
02960521
02971400
02971400
5312316
5312316
00037200
00037200
4720
4720
02972567
00024400
02972570
02972256
00750959
00001300
02972549
02972807
00750940
02971423
02972505
00749495
02822500
02972353
02972352
02972262
02972261
65010300
00015800
00751281
02972355
02971928
02918600
02971720
02971701
02971702
165020
02971756
02970595
--1
1
1
1
1
1
1
1
1
2
3
3
4
3
4
11
12
3
4
1
9
9
1
4
4
1
2
2
1
1
2
2
1
2
2
2
2
3
3
1
1
7
1
1
1
1
1
1
TIMBERCAT HEAD ASY, 5 FOOT
TIMBERCAT HEAD ASY, 7 FOOT
BOTTOM BLADE, 5 FOOT
BOTTOM BLADE, 7 FOOT
TOP BLADE, 5 FOOT
TOP BLADE, 7 FOOT
SLIDE BEARING, 5 FOOT
SLIDE BEARING, 7 FOOT
FRONT COVER, 5 FOOT
FRONT COVER, 7 FOOT
BOLT
BOLT, 5 FOOT
BOLT, 7 FOOT
BUSHING, 5 FOOT
BUSHING, 7 FOOT
WASHER, 5 FOOT
WASHER, 7 FOOT
LOCKNUT, 5 FOOT
LOCKNUT, 7 FOOT
GREASE FITTING, 5 FOOT
GREASE FITTING, 7 FOOT
TIMBERCAT FRAME
BOLT
LOCKWASHER
VALVE MOUNT FRAME
BOLT
LOCKWASHER
INVERSION VALVE
BOLT
LOCKNUT
CYLINDER, ASY.
PIN
COTTER PIN
WASHER
CYLINDER MOUNT
BOLT
SPRING
ADJUSTING BOLT
NUT
LOCKNUT
JAMNUT
COVER
HITCH POST, F/ MACHETE
BOLT
PIN
WASHER
LOCKNUT
COTTER PIN
PIN
BOLT
MACHETE - M/B 17,21,24 (APR-04)
TIMBERCAT HEAD ASY. (ITEMS 40 THRU 68)
MACHETE - M/B 17,21,24 (APR-04)
TIMBERCAT HEAD ASY. (ITEMS 40 THRU 68)
ITEM
PART NO.
QTY.
DESCRIPTION
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
00752735
00023500
02972507
02957501
02972568
02972791
10058000
00024100
02959924
00021400
00017000
02962213
02042300
001582
02972796
02161300
02972569
02969464
02972800
02972799
02959390
02972980
02972981
02972982
02965464
00751003
02973007
02753400
02965464
7
7
1
1
1
1
2
6
2
2
2
2
3
1
1
2
1
3
1
1
2
1
1
1
1
1
1
2
1
SELF TAPPING SCREW
WASHER
PIN
BUSHING
MANIFOLD BLOCK
MANIFOLD BRACKET
BOLT
WASHER
NUT
BOLT
LOCKWASHER
ADPATER, 90`
ADAPTER, STRAIGHT
PLUG
ADAPTER, STRAIGHT
ADAPTER, 90 `
RELIEF VALVE
ADAPTER, REDUCER
HOSE
HOSE
BOLT
HOSE - W/ RED TIE (R)
HOSE - W/ BLUE TIE (B)
HOSE - W/ ORANGE TIE (OR)
SLEEVING, (NOT SHOWN)
PLUG
HOSE BRACKET
PLASTIC TIE
HOSE SLEEVING
MACHETE - M/B 17,21,24 (APR-04)
ALAMO INDUSTRIAL
LIMITED
WARRANTY
1. LIMITED WARRANTIES
1.01.Alamo Industrial warrants for one year from the purchase date to the original non-commercial, governmental, or
municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser
(“Purchaser”) that the goods purchased are free from defects in material or workmanship.
1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be
defective under normal use and service due to defects in material or workmanship.
1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use,
negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or
lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal
combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found
in your Operator’s Manual.
1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any
nature on behalf of Manufacturer.
2. REMEDIES AND PROCEDURES.
2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer
within 30 days of purchase.
2.02.Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the
goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the
claim is based.
2.03.Purchaser is responsible for returning the goods in question to the Dealer.
2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and
service due to defects in material or workmanship, Manufacturer will:
(a) Repair or replace the defective goods or part(s) or
(b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer)
if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty
by Manufacturer.
The choice of remedy shall belong to Manufacturer.
2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and
for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory.
3. LIMITATION OF LIABILITY.
3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES
WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR
USE OF THE GOODS.
3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO
PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE
CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT
LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM
THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE
ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGES
INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS.
3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER
THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS
OCCURRED.
4. MISCELLANEOUS.
4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County,
Texas.
4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall
be deemed to be a waiver of any other term.
4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the
invalidity of such provision shall not invalidate any other provisions herein.
4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein.
KEEP FOR YOUR RECORDS
ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine
identification when applying for warranty.
Alamo Industrial Implement Model ____________________________ Serial Number ________________________________
Date Purchased __________________________________________ Dealer ______________________________________
ATTENTION:
READ YOUR OPERATOR'S MANUAL
ALAMO INDUSTRIAL
An Alamo Group Company
Post Office Drawer 549
Seguin, Texas 78156
830-379-1480
TO THE OWNER/OPERATOR/DEALER
To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions
and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can
easily find the information you need.
The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety
requirements of tractor operators:
REQUIRED OF THE OWNER:
1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and
2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C;
and
3. Ensure that each employee uses such Seatbelt while the tractor is moving; and
4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the
protected area provided by the ROPS.
REQUIRED OF THE OPERATOR
1.
2.
3.
4.
5.
6.
7.
8.
9.
Securely fasten seatbelt if the tractor has a ROPS.
Where possible, avoid operating the tractor near ditches, embankments, and holes.
Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.
Stay off slopes too steep for safe operation.
Watch where you are going - especially at row ends, on roads, and around trees.
Do not permit others to ride.
Operate the tractor smoothly - no jerky turns, starts, or stops.
Hitch only to the drawbar and hitch points recommended by the tractor manufacturer.
When the tractor is stopped, set brakes securely and use park lock, if available.
Keep children away from danger all day, every day...
Equip tractors with rollover protection (ROPS) and keep all
machinery guards in place...
Please work, drive, play and live each day with care and
concern for your safety and that of your family and fellow
citizens.
MB21&24 - OMWPL - 04/04
Printed U.S.A.
P/N 02968915P

parts manual - Alamo Industrial

Transcription

Similar documents

SR15 SR10 MPB PUB 06-05 REV 04-06

00764581MB---FM15 FM10 MPB PUB 07-05 Rev 10-11

TURBO 120 MPB PUB 09-05 Rev 11-05

rotary mower parts - rotary cutter parts

KB1800 Parts Manual