TURBO 120 MPB PUB 09-05 Rev 11-05

Transcription

TURBO 120
ROTARY CUTTER
P/N 00778487MB
Rev 11-05
MASTER PARTS BOOK
S/N 10001 TO CURRENT
PARTS LISTING
Rhino®
An Alamo Group Company
1020 S. Sangamon Ave.
Gibson City, Il 60936
1-800-446-5158
Email: [email protected]
© 2005 Alamo Group Inc.
TO THE OWNER/OPERATOR/DEALER
All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who
recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to
be used with all its safety equipment properly attached to minimize the chance of accidents.
BEFORE YOU START!! Read the safety messages on the implement and shown in your manual.
Observe the rules of safety and common sense!
WARRANTY INFORMATION:
Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form
in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card
and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic
failure with possible injury or death.
PARTS
SECTION
Parts Section – 1
PARTS ORDERING GUIDE
The following instructions are offered to help eliminate needless delay and error in processing
purchase orders for the equipment in this section.
1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the
basic machine featured in this manual. Part Numbers and Descriptions are given to help
locate the parts and quantities required.
2. The Purchase Order must include the name and address of the person or organization
ordering the parts, who should be charged, and if possible, the serial number of the machine
for which the parts are ordered.
3. The Purchase Order must clearly list the quantity of each part, the complete and correct part
number (be sure to include all periods), and the basic name of the part.
4. The Manufacturer reserves the right to substitute parts where applicable.
5. Some parts are unlisted items which are special production items not normally stocked and
are subject to special handling. Request a quotation for such parts before sending a
Purchase Order.
6. The Manufacturer reserves the right to change prices without prior notice.
NOTE:
Please refer to The Safety Section in the front of this Manual for the proper
Part Number when ordering Replacement Safety Decals.
For maximum safety and to guarantee optimum product reliability, always use
genuine Servis-Rhino Parts. The use of inferior replacement parts may cause
premature or catastrophic failure which could result in serious injury or death.
Direct any questions regarding parts to:
RHINO ®
Gibson City, IL 60936
800-446-5158
©2005 Alamo Group Inc.
Parts Section – 2
PART NAME INDEX
A-FRAME ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT ............................................................................. 4
AXLE ASSEMBLY - HYDRUALIC OFFSET S/N 10001 - CURRENT DEC 2004 - CURRENT ............................................ 5
AXLE ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT .................................................................................... 6
BLADE PAN ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT......................................................................... 7
CASTER WHEEL & FORK ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT .................................................. 8
CHAIN GUARD ASSEMBLY - FRONT S/N 10001 - CURRENT DEC 2004 - CURRENT .................................................... 9
CHAIN GUARD ASSEMBLY - REAR S/N 10001 - CURRENT DEC 2004 - CURRENT .................................................... 10
CONTROL ROD ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT ................................................................ 11
CYLINDER - CENTER S/N 10001 - CURRENT DEC 2004 - CURRENT ........................................................................... 12
DEFLECTOR ASSEMBLY - FRONT S/N 10001 - CURRENT DEC 2004 - CURRENT ..................................................... 13
DEFLECTOR ASSEMBLY - REAR S/N 10001 - CURRENT DEC 2004 - CURRENT ........................................................ 14
DRIVELINE ASSEMBLY - LIFT TYPE 1000 RPM S/N 10001 - CURRENT DEC 2004 - CURRENT ............................... 19
DRIVELINE ASSEMBLY - LIFT TYPE 540 RPM S/N 10001 - CURRENT DEC 2004 - CURRENT ................................. 20
DRIVELINE ASSEMBLY - CV 1000 RPM S/N 10001 - CURRENT DEC 2004 - CURRENT ............................................. 15
DRIVELINE ASSEMBLY - CV 540 RPM S/N 10001 - CURRENT DEC 2004 - CURRENT ............................................... 16
DRIVELINE ASSEMBLY - JACKSHAFT S/N 10001 - 10199 DEC 2004 - OCT 2005 ........................................................ 17
DRIVELINE ASSEMBLY - JACKSHAFT S/N 10200 - CURRENT OCT 2005 - CURRENT................................................ 18
DRIVELINE ASSEMBLY - OUTER S/N 10001 - CURRENT DEC 2004 - CURRENT ........................................................ 21
DRIVELINE ASSEMBLY - PULL TYPE 1000 RPM S/N 10001 - CURRENT DEC 2004 - CURRENT............................... 22
DRIVELINE ASSEMBLY - PULL TYPE 540 RPM S/N 10001 - CURRENT DEC 2004 - CURRENT................................. 23
GEARBOX ASSEMBLY - DIVIDER 1000 RPM S/N 10001 - CURRENT DEC 2004 - CURRENT ..................................... 24
GEARBOX ASSEMBLY - DIVIDER 540 RPM S/N 10001 - CURRENT DEC 2004 - CURRENT ....................................... 25
GEARBOX ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT ......................................................................... 26
GEARBOX SHIELD ASSEMBLY - DIVIDER PULL TYPE S/N 10001 - CURRENT DEC 2004 - CURRENT ................... 29
GEARBOX SHIELD ASSEMBLY - DIVIDER LIFT TYPE S/N 10001 - CURRENT DEC 2004 - CURRENT ...................... 28
GEARBOX SHIELD ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT ........................................................... 30
HITCH ASSEMBLY - HYDRUALIC OFFSET MODELS/N 10001 - CURRENT DEC 2004 - CURRENT............................ 31
SKID SHOE ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT ....................................................................... 32
SLIP CLUTCH ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT.................................................................... 33
SPRING POD ASSEMBLY - OPTIONAL S/N 10001 - CURRENT DEC 2004 - CURRENT............................................... 34
TAILWHEEL ASSEMBLY - LIFT TYPE S/N 10001 - CURRENT DEC 2004 - CURRENT ................................................. 35
TIRES S/N 10001 - CURRENT DEC 2004 - CURRENT ..................................................................................................... 36
TONGUE ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT............................................................................ 37
WHEEL HUB ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT...................................................................... 38
TURBO 120 Master Parts Book (Sept-05) Rev 11-05
Parts Section – 3
A-FRAME ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
0758550020
0758550010
00778496
00778084
69141
00037200
00007800
0758550070
00001800
00748823
0758550031
5JRC16140
7AH5161436
5312316
0758550030
00009500
00037100
2196
3730110M
00778495
00778651
00778185
1
1
2
1
2
5
2
4
10
10
1
1
1
3
1
1
2
3
1
1
1
1
A-FRAME WELDMENT L.H.
A-FRAME WELDMENT R.H.
REAR BRACE
REAR BRACE WELDMENT
HITCH PIN CAT II & III
LOCKNUT 3/4 NC PLB
BOLT
BUSHING
TOPLOCKNUT
BOLT
BUSHING
LOCKNUT
BOLT
WASHER
SPACER
BOLT
BOLT
CLIP LYNCH PIN
PIN-TOP LINK
SPACER
DRIVELINE HOLDER BRKT.
AXLE PIVOT PIN
Parts Section – 4
AXLE ASSEMBLY - HYDRUALIC OFFSET S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
00777455
00778518
00778062
00778185
02959587
00776220
02030700
00001800
00554600
47264-8
1
2
2
3
8
2
3
5
1
8
AXLE WELDMENT
CASTER ARM WELDMENT
AXLE ARM PLATE
AXLE PIVOT PIN
BOLT
CASTER WHEEL ASSEMBLY
BOLT
TOPLOCKNUT
RATCHET JACK ASSEMBLY
LOCKNUT
Parts Section – 5
AXLE ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
00778158
8727A
00775616A
00778185
8354
02822500
02959587
00778062
00777455
00778063
00606000
02030700
00001800
00764375
00777963
103266
00037200
00778530
03200347
10058000
02959924
00001800
1
1
2
3
1
3
8
2
1
2
3
6
11
2
1
1
8
1
1
2
2
1
SPING POD ASSEMBLY *(OPTIONAL)*
HYDRUALIC CYLINDER
SPINDLE HUB ASSEMBLY
AXLE PIVOT PIN
PIN HYD. CYLINDER
FLATWASHER
BOLT
AXLE ARM PLATE
AXLE WELDMENT
AXLE ARM WELDMENT
COTTER PIN
BOLT
TOPLOCKNUT
BOLT
TRANSPORT LOCK PLATE
CYLINDER PIN
LOCKNUT
SMV BRACKET MOUNT PLATE
SMV SIGN
BOLT (TORQUE TO 250 POUNDS)
NUT
LOCKNUT TLM 1/2 NC PLB
Parts Section – 6
BLADE PAN ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
00778067
00778068
8590
8589
8251
00778047
5JRC16140
8216
1
1
1
1
2
2
2
2
DISHPAN ASSEMBLY, CW
DISHPAN ASSEMBLY, CCW
KNIVES MTCH SET CW
KNIVES MTCH SET CCW
BLADE BOLT SPECIAL
WASHER-SQUARE ID
LOCKNUT 1 -14 TLDT GC ZP
HHCS 1/2-13NC 1 PLAIN
Parts Section – 7
CASTER WHEEL & FORK ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
00776220
373024H
00776214
00776213
00776219
00772082
00776216
7A6166
00776215
00012101
00013901
0585020210A
00772017
00772018
00776211
02822500
15B2400
00776212
00771620
00758899
1
1
2
2
1
4
4
4
4
4
1
2
2
1
1
2
1
1
1
ASSY CASTER FORK & WHEEL
WHEEL & TIRE ASSY
HUB 4 BOLT
BEARING
SEAL OIL 40 X 62 X 8
NIPPLE, GREASE M8X1
BOLT M12 X 1.5 X 25
HHCS 3/8 NC 3/4
LUG BOLT FLAT WASHER
LOCKWASHER 3/8 PL HVY
NUT HEX 3/8 NC PL
WLDMT CASTER FORK
BUSHING SPINDLE STEP
DUST CAP
BOLT SPINDLE M24 X 2 X 186
FLATWASHER 1 PL STD
FLATWASHER NAR 1-1/2 PL
NUT SPINDLE M24 X 2
PIN,COTTER 5/32X2-1/2 PL
PIN COTTER 3/8X2-1/2 PL EXTEND
Parts Section – 8
CHAIN GUARD ASSEMBLY - FRONT S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
00778087
00778486
00778485
00748823
00001300
00002700
00001800
00777370
00992000
00777374
00777369
00778483
00778484
00992000
2
1
1
14
10
8
8
108
5.25ft
8
8
1
1
.58ft
CHAINGUARD ASSEMBLY FRONT
SIDE CHAINGUARD ASY LEFT
SIDE CHAINGUARD ASY RIGHT
HHCS 1/2-13UNC 1-1/2 PL5
LOCKWASHER 1/2 PL STD
FLATWASHER 1/2 PL STD
CHAIN,5/16
CABLE, 1/4 GA AIRCRAFT (7X19)
CABLE STOP, ALUMINUM 1/4
CHAIN,5/16
CHAINGUARD BRACKET FRT RIGHT
CHAINGUARD BRACKET FRT LEFT
Parts Section – 9
CHAIN GUARD ASSEMBLY - REAR S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
00762182
02030700
00762139
00992000
00777374
4526
00777369
2
6
2
7ft
4
6
70
BNDL-REAR CHAINGUARDS (BLACK)
HHCS 1/2-13UNC 1-1/4 PL5
PL-REAR CHAINGUARD
CABLE STOP, ALUMINUM 1/4
NUT LOCK FLG WHIZ 1/2-13 NC PL
CHAIN,5/16
Parts Section – 10
CONTROL ROD ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
00762147
743031
00758643
00778159
651102
5C1490
15B1200
00755153
2
2
2
4
2
8
4
CONTROL ROD ASSEMBLY
CONTROL ROD, WLDT, L.H. THDS
CONTROL ROD, WLDT. R.H. THDS
NUT, ADJUSTING
ROD PIN, CONTROL
NUT, JAM
WASHER
PIN, COTTER
CYLINDER - CENTER S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
1
2
3
4
5
6
9
15
16
17
18
19
20
21
PART NO.
QTY.
DESCRIPTION
8727A
00774729
00774734
00774730
00774753
3047111
3047112
00774760
3047117
1917140
00774740
33003H5C
5JRC12160
1917132
2417154
651132
94514
0652141311
8354
00606000
1
1
1
1
1
4
1
1
1
1
8
1
1
1
2REF
2REF
2REF
2REF
2REF
CYLINDER HYD 2-1/2 8
CLEVIS CAP 2.5-3/4 ORB-1.00
ROD CAP 2.50-1.25-3/4 ORB
PISTON 2.5-0.75-S HALL W/RING
ROD CYL 1.25-08-0.75-1.25-A
CYLINDER TUBE
TIE ROD
SEAL KIT FOR 8727A & 8728A CYL
THREAD LOCK
ROD CLEVIS
SC SCKT SET 3/8UNCX1/2 KNUR
HEX NUT 3/8-16 GR.5
NUT TOPLOCK 3/4 NF PLC
SCKT HD O-RNG PLUG,3/4-16 UNF,
BREATHER,CYLINDER #8 ORB
HOSE #6 - 8MP - 8MP - 144LG
ADAPTER, HYD, ELBOW SWIVEL
ADP HYD STGHT 8MB - 8FP
PIN-HYD. CYLINDER
PIN-COTTER 3/16 X 2
DEFLECTOR ASSEMBLY - FRONT S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
00778092
00778091
00778486
00778485
00748823
00002700
00001800
00778483
00778484
00777374
00992000
00001300
00778089
2
2
1
1
14
8
8
1
1
4
.58ft
10
2
DEFLECTOR, FRONT
DEFLECTOR BRACKET, FRONT
SIDE CHAINGUARD ASY LEFT
SIDE CHAINGUARD ASY RIGHT
HHCS 1/2-13UNC 1-1/2 PL5
CHAINGUARD BRACKET FRT RIGHT
CHAINGUARD BRACKET FRT LEFT
CABLE STOP, ALUMINUM 1/4"
LOCKWASHER 1/2 PL STD
DEFLECTOR ASSEMBLY, FRONT
DEFLECTOR ASSEMBLY - REAR S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
00762180
00762142
00762144
4526
02030700
2
2
6
6
DEFLECTOR ASSEMBLY-REAR
SHIELD
BAR STRAP
LOCKNUT
BOLT
DRIVELINE ASSEMBLY - CV 1000 RPM S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
PART NO.
QTY.
DESCRIPTION
00775306
00775379
8381
8382
00775309
8396
0921000333
00775380
00775381
00775310
00775311
8388
8393
00763951
8949
1416601
00759217
8974
00775304
00775305
00767953
00774208
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
8
1
1
1
1
1
DRIVELINE 1000 CV CAT 4
YOKE 1-3/8-21 SPL ASG
DOUBLE YOKE
FITTING,GREASE M8 X 1
YOKE INBOARD S4
CROSS & BEARING KIT
PIN-SPRING 10 X 80
INNER PROFILE S4GA
SLEEVE & PROFILE W.A.
YOKE INBOARD S5
YOKE 1-3/4-20 SPL CC
CROSS & BEARING KIT
BEARING RING
DRIVELINE- CV CONE BRG ASY
SHIELD CONE
ZERK
SCREW 1/2 LG END
SUPPORT BEARING
SHIELD OUTER HALF
SHIELD INNER HALF
YOKE.Q.D.KIT - METAL
LOCK ASY CC YOKE
DRIVELINE ASSEMBLY - CV 540 RPM S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
PART NO.
QTY.
DESCRIPTION
00775301
8380
8381
8382
00775309
8396
0921000333
00775380
00775381
00775310
00775311
8388
8393
00763951
8949
1416601
00759217
8974
00775304
00775305
00767953
00774208
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
8
1
1
1
1
1
DRIVELINE 540 CV SR5 60 1/3/8YOKE - 1-3/8 6 SPLING COMP.
DOUBLE YOKE
FITTING,GREASE M8 X 1
YOKE INBOARD S4
CROSS & BEARING KIT
PIN-SPRING 10 X 80
INNER PROFILE S4GA
SLEEVE & PROFILE W.A.
YOKE INBOARD S5
YOKE 1-3/4-20 SPL CC
CROSS & BEARING KIT
BEARING RING
DRIVELINE- CV CONE BRG ASY
SHIELD CONE
ZERK
SCREW 1/2 LG END
SUPPORT BEARING
SHIELD OUTER HALF
SHIELD INNER HALF
LOCK ASY CC YOKE
DRIVELINE ASSEMBLY - JACKSHAFT S/N 10001 - 10199 DEC 2004 - OCT 2005
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
14
15
16
00776419
00776420
00189700
00756934
00776421
00775318
00775331
------------------------------------8393
------------00759217
8974
1416601
1
1
1
1
1
1
1
1
1
2
1
2
1
1
D/L 1-3/4-20 CAT4 1000 RPM
STUB AND PROFILE W.A.
CROSSKIT
PIN,ROLL 10 X 80
PROFILE AND SLEEVE W.A.
YOKE INBOARD 2A
CLUTCH FRICTION
GUARD RING
OUT. SHIELD TUBE OVL.
INN. SHIELD TUBE RND
BEARING RING
SHIELD CONE- SHORT
SCREW 1/2 LG END
SUPPORT BEARING
ZERK
DRIVELINE ASSEMBLY - JACKSHAFT S/N 10200 - CURRENT OCT 2005 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
00778221
00778536
00189700
00756934
00778537
00775318
00775331
---------------------------------8393
-----------00756005
00756004
00759217
00778535
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
DRIVELINE ZW1340 JACKSHAFT
STUB AND PROFILE W.A.
CROSSKIT
PIN,ROLL 10 X 80
OUTER PROFILE
YOKE INBOARD 2A
CLUTCH FRICTION
GUARD RING
OUT. SHIELD TUBE OVL
BEARING RING
SHIELD CONE - SHORT
DECAL-ROTATING DRIVELINE
DECAL-SHIELD MISSING
SCREW 1/2 LG END
COMPLETE SHIELD ASSEMBLY
DRIVELINE ASSEMBLY - LIFT TYPE 1000 RPM S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
00775390
00761762
W279R
8384
00775317
7413
00775377
00775318
00775331
8393
00759217
8974
1416601
00775388
00775389
00767953
1
2
2
1
1
1
1
1
2
2
1
1
1
1
1
DRIVELINE 43.75 LG X 1-3/8-21
YOKE 1-3/8-21 SPL PAINT BLACK
CROSS REPAIR KIT, CTR
SPRING PIN 10MM X 90MM
YOKE INBOARD 1B
INNER PROFILE
PROFILE & SLEEVE W.A.
YOKE INBOARD 2A
CLUTCH FRICTION
BEARING RING
SCREW 1/2 LG END
SUPPORT BEARING
ZERK
OUTER SHIELD HALF
INNER SHIELD HALF
DRIVELINE ASSEMBLY - LIFT TYPE 540 RPM S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
00775385
00775353
W279R
8384
00775317
7413
00775377
00775318
00775331
8393
00759217
8974
1416601
00775388
00775389
00767954
1
2
2
1
1
1
1
1
2
2
1
1
1
1
1
DRIVELINE 43.75 LG X 1-3/8-6QD
YOKE 1-3/8-6 SPLINE ASGE
CROSS REPAIR KIT, CTR
SPRING PIN 10MM X 90MM
YOKE INBOARD 1B
INNER PROFILE
YOKE INBOARD 2A
CLUTCH FRICTION
BEARING RING
SCREW 1/2 LG END
SUPPORT BEARING
ZERK
OUTER SHIELD HALF
INNER SHIELD HALF
YOKE.Q.D.KIT - PLASTIC
DRIVELINE ASSEMBLY - OUTER S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
00777983
00778169
00762215
00766475A
00771287
00762216A
00765902
00765962
00764386
1
4
48
24
2
12
12
2
DRIVELINE ASSY
DOUBLE FLEX YOKE & TUBE ASSEMBLY
FLEX COUPLER RUBBER DISK
FLEX COUPLER SHAPED WASHER
FLEX COUPLER BUSHING
FLEX CONNECTOR YOKE 1 3/4"-20
HEX HEAD CAP SCREW
SELF LOCKING HEX NUT
GREASE ZERK
DRIVELINE ASSEMBLY - PULL TYPE 1000 RPM S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
00761762
00189700
00756934
00775317
0921000332
00775378
00775318
00775316
-----------------------------------8393
00756005
00756004
00759217
8974
00776879
00775384
00775327
1
2
2
1
1
1
1
1
2
1
1
2
1
1
2
1
1
2
2
YOKE 1-3/8-21 SPL PAINT BLACK
CROSSKIT
PIN,ROLL 10 X 80
YOKE INBOARD 1B
TUBE, SHAFT
YOKE INBOARD 2A
YOKE 1-3/4-20 SPL I.C.
SHIELD CONE
BEARING RING
SCREW 1/2 LG END
SUPPORT BEARING
PLATE,CLEVIS
BOLT P1.75 M12 X 60
NUT P1.75 M12
DRIVELINE ASSEMBLY - PULL TYPE 540 RPM S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
00775353
00189700
00756934
00775317
0921000332
00775378
00775318
00775316
----------------------------------8393
00756005
00756004
00759217
8974
00776879
00775384
00775327
1
2
2
1
1
1
1
1
2
1
1
2
1
1
2
1
1
2
2
YOKE 1-3/8-6 SPLINE ASGE
CROSSKIT
PIN,ROLL 10 X 80
YOKE INBOARD 1B
TUBE, SHAFT
YOKE INBOARD 2A
YOKE 1-3/4-20 SPL I.C.
SHIELD CONE
BEARING RING
SCREW 1/2 LG END
SUPPORT BEARING
PLATE,CLEVIS
BOLT P1.75 M12 X 60
NUT P1.75 M12
GEARBOX ASSEMBLY - DIVIDER 1000 RPM S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
00778034
00778022
00755954
00758659
00770734
00778023
00758653
00769938
00758646
00758647
00758648
00778027
00762521
00778028
00777884
00778030
00778031
00762121
00770421
00769321
00778534
00758657
00777885
00778033
00770737
1
24
24
2
1
2
4
VAR
VAR
VAR
1
1
1
1
VAR
VAR
1
1
1
1
1
1
1
1
DIVIDER GEARBOX 1000 RPM
HOUSING
LOCKWASHER
BOLT M10 X 1.5 X 30
INPUT CAP
SHAFT
INPUT OIL SEAL
BEARING ASSEMBLY
INPUT CAP GASKET 0.15
DIVIDER HUB CAP
OIL SEAL
DIVIDER INPUT SHAFT
20 TOOTH PINION
DIVIDER GASKET 0.10
DIVIDER GASKET 0.25
BEARING ADJUSTING NUT
COTTER PIN
COPPER SEALING WASHER
DIP STICK BREATHER ASSEMBLY
BEARING SPACER
DIVIDER 23 TOOTH GEAR
DIVIDER BEARING SPACER
HEX HEAD LEVEL PLUG
GEARBOX ASSEMBLY - DIVIDER 540 RPM S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
00778021
00778022
00755954
00758659
00770734
00778023
00758653
00769938
00758646
00758647
00758648
00778027
00762521
00778028
00778029
00778030
00778031
00762121
00770421
00769321
00778534
00758657
00778032
00778033
00770737
1
24
24
2
1
2
4
VAR
VAR
VAR
1
1
1
1
VAR
VAR
1
1
1
1
1
1
1
1
DIVIDER GEARBOX 540 RPM
HOUSING
LOCKWASHER
BOLT M10 X 1.5 X 30
INPUT CAP
SHAFT
INPUT OIL SEAL
BEARING ASSEMBLY
DIVIDER HUB CAP
OIL SEAL
DIVIDER INPUT SHAFT
AG SUPER 200 DIVIDER 25 T GEAR
DIVIDER GASKET 0.10
DIVIDER GASKET 0.25
COTTER PIN
COPPER SEALING WASHER
BEARING SPACER
DIVIDER 15 TOOTH GEAR
DIVIDER BEARING SPACER
HEX HEAD LEVEL PLUG
GEARBOX ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT
GEARBOX ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
00777840
00777882
00755954
00762398
00777881
00777880
00758653
00777879
00777879
00758667
00762153
00758668
00778226
00777876
00771227
01422502
00777874
00777873
00777872
00777884
00762121
00770421
00769938
00777870
00777869
00777868
00777867
61368C8
00777866
00769321
00762123
00758657
00777883
00777865
00777885
02969728
00778621
1
18
12
1
1
1
VAR
VAR
VAR
VAR
VAR
1
1
1
1
1
1
1
1
1
1
3
1
VAR
VAR
1
6
1
2
2
1
1
1
1
2
1
GEARBOX ASSEMBLY
HOUSING
LOCKWASHER
HEX HEAD BOLT M10X 1.5 X 30
INPUT CAP
INPUT SHAFT
INPUT OIL SEAL
SHIM 0.30
SHIM 0.40
SHIM 0.50
BEARING ASSEMBLY
SEAL PROTECTOR
BLADE HUB
COTTER PIN
HEX SLOTTED FLANGED NUT M36
OUTPUT OILSEAL
OUTPUT SAFT
TOOTH PINION
COTTER PIN 3.6MM X 65MM
BEARING ASSEMBLY
BLANK ADJUSTING CAP
BLANK CAP GASKET 0.10
BLANK CAP GASKET 0.25
BEARING SPACER
HEX HEAD BOLT M10 X 1.5 X 30
INSPECTION COVER CAP
SEALING WASHER
HEX HEAD PLUG M18X1.5
INPUT SHAFT SPACER
INSPECTION COVER GASKET
TOOTH GEAR
HEX HEAD BOLT M6 X 1 X 20
OUTPUT SEAL PLATE
GEARBOX SHIELD ASSEMBLY - DIVIDER LIFT TYPE S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
00778649
1
BRACKET, SHIELD MOUNT
GEARBOX SHIELD ASSEMBLY - DIVIDER PULL TYPE S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
00778149
-
SHIELD WELDMENT, DIVIDER
GEARBOX SHIELD ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
00778670
00778664
00778665
00778666
00011100
000644
00011400
00015800
00769933
2
1
1
1
6
2
2
2
2
SHIELD ASSEMBLY
SHIELD , COUPLER
CARB 3/8 NC 1-1/4 PL5
HHCS 3/8 NC 1 PL5
NUT,TOPLOCK 3/8NC PLB
NUT-PLASTIC KNOB 3/8 NC PL
HITCH ASSEMBLY - HYDRUALIC OFFSET MODELS/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
00778508
00749941
00778515
00778514
8727A
00778519
8354
00771281
01422502
00606000
0781080000
00772458
2196
15D1200
00606700
0651131200
0652141311
1
4
1
1
1
1
2
4
4
2
2
2
2
3
2
2
2
OFFSET HITCH WELDMENT
FLATWASHER
SWING ARM WELDMENT R.H.
SWING ARM WELDMENT L.H.
HYDRUALIC CYLINDER
CYLINDER BRACKET WELDMENT
PIN HYD. CYLINDER
PIVOT PIN WELDMENT
COTTER PIN
COTTER PIN
WRIST PIN
SPACER
CLIP LYNCH PIN
WASHER
ADAPTER, HYD, ELBOW
HOSE
STRAIGHT ADAPTER
SKID SHOE ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
00776618
2A361612
00011100
00015800
2
6
6
6
SKID SHOE
PLOW BOLT
FLATWASHER
NUT
SLIP CLUTCH ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
00775331
00775333
8366
00775334
00775335
00775336
00775337
00775338
00775339
00754566
00756164
00775327
00775328
1
4
1
1
1
1
6
6
6
6
2
2
SLIP CLUTCH
FLANGE YOKE
FRICTION DISK
HUB
DRIVE PLATE
DRIVE PLATE
THRUST PLATE
BOLT
COMPRESSION SPRING
LOCKWASHER
LOCKNUT
LOCKNUT
BOLT
SPRING POD ASSEMBLY - OPTIONAL S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
00778158
00778154
00778155
00759190
371063A
8354
00761199
02030300
02822500
00750952
00695100
00037100
00037200
00606000
7A16824
1
1
1
2
1
1
1
2
1
1
1
1
1
1
SPRING POD ASSEMBLY
SPRING POD BASE LH.
SPRING POD BASE RH.
SPRING SHOCK WELDMENT
SPRING
PIN
SPACER TUBE
LOCKNUT TLM 1" NC PLB
FLAT WASHER 1 PL STD
BOLT 5/8 X 2 1/2 NC GR5 PL
TOPLOCK NUT, 5/8 NC
BOLT 3/4 NC X 2-1/2" PL5
LOCKNUT 3/4 NC PLB
COTTER PIN 3/16 X 2"
BOLT 1 NC X 3" PL5
TAILWHEEL ASSEMBLY - LIFT TYPE S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
4745
00778076
00001800
00748823
15D1200
00778498
00776220
00695100
00778652
02845800
2
2
10
10
4
2
2
2
2
2
TAILWHEEL POSITIONING BRACKET
CASTER ARM MOUNT WELDMT.
TOPLOCKNUT
BOLT
WASHER
TAILWHEEL BEAM WELDMENT
CASTER WHEEL ASSEMBLY
NUT
BEAM SUPPORT
BOLT
TIRES S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
00766911
00766911A
00008700
00025200
1
1
ASY,AIRCRAFT TIRE & WHEEL
ASY,AIRCRAFT TIRE & WHEEL
WHEEL, RIM ONLY
NOTAT TIRE & WHEEL
TONGUE ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
*
*
28
00761890
00758146
00778058
00778053
00760941
00778221
00754107
02030300
00772391
00752671
00037200
02030700
00001800
00756077
00695100
00002700
02965484
00778524
00749130
2196
00001300
00748823
1431565
40010000
00778130
00777459
00775006A
00767705
00764417
00778735
2
2
1
1
1
1
2
2
1
1
2
6
11
1
2
6
1
1
1
2
2
2
1
1
1
1
1
1
1
1
BUSHING
PIN TONGUE PIVOT
CARRIER MOUNT WELDMENT
CLEVIS WELMENT
JACK TUBE MOUNT WELDMENT
JACK SHAFT
BOLT
NUT TOPLOCK 1" NC PLB
PARKING JACK
BOLT
LOCKNUT
BOLT
TOPLOCKNUT
HARDENED WASHER
TOPLOCK NUT
FLATWASHER
HOSE BRACKET, SPRING BASE
JACK MOUNT TUBE WLDMT.
BOLT
CLIP LYNCH PIN
LOCKWASHER
BOLT
DRIVELINE HOLDER
COTTER PIN
DRIVELINE, MAIN
TONGUE WELDMENT
BEARING ASSEMBLY
SNAP RING JACKSHAFT BEARING
BEARING,BALL 1-1.77IDX3.346OD
SPACER
* - PARTS OF ASSEMBLY # 00775006A
WHEEL HUB ASSEMBLY S/N 10001 - CURRENT DEC 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
00775616A
00774821
00756000
00756492
00756488
00778108
00756014
00756490
00756793
00026200
00750434
00756576
0371242102
00756577
00003500
1
1
1
5
1
5
1
1
1
1
1
1
1
1
COMPLETE HUB & SPINDLE ASSY.
SPINDLE
WHEEL HUB CASTING
DUST CAP
STUD BOLT 1/2" -20 UNF
SEAL KIT
WHEEL NUT 1/2"-20 UNF
BEARING ADJUSTING NUT 1"-14UNS
WASHER 1"
COTER PIN 1/8" X 2-3/8" LNG
BEARING CONE INSIDE
BEARING CUP OUTSIDE
BEARING CONE INSIDE
BEARING CUP OUTSIDE
GREASE FITTING
SERVIS-RHINO
LIMITED
WARRANTY
1. LIMITED WARRANTIES
1.01.Servis-Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal
purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”)
that the goods purchased are free from defects in material or workmanship.
1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be
defective under normal use and service due to defects in material or workmanship.
1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use,
negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or
lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal
combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found
in your Operator’s Manual.
1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any
nature on behalf of Manufacturer.
2. REMEDIES AND PROCEDURES.
2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer
within 30 days of purchase.
2.02.Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the
goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the
claim is based.
2.03.Purchaser is responsible for returning the goods in question to the Dealer.
2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and
service due to defects in material or workmanship, Manufacturer will:
(a) Repair or replace the defective goods or part(s) or
(b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer)
if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty
by Manufacturer.
The choice of remedy shall belong to Manufacturer.
2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and
for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory.
3. LIMITATION OF LIABILITY.
3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES
WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR
USE OF THE GOODS.
3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO
PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE
CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT
LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM
THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE
ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGES
INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS.
3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER
THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS
OCCURRED.
4. MISCELLANEOUS.
4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County,
Texas.
4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall
be deemed to be a waiver of any other term.
4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the
invalidity of such provision shall not invalidate any other provisions herein.
4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein.
KEEP FOR YOUR RECORDS
ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine
identification when applying for warranty.
Servis-Rhino Implement Model _______________________________ Serial Number ________________________________
Date Purchased __________________________________________ Dealer ______________________________________
ATTENTION:
READ YOUR OPERATOR'S MANUAL
RHINO®
Gibson City, IL 60936
800-446-5158
TO THE OWNER/OPERATOR/DEALER
To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and
the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily
find the information you need.
The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety
requirements of tractor operators:
REQUIRED OF THE OWNER:
1.
2.
3.
4.
Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and
Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and
Ensure that each employee uses such Seatbelt while the tractor is moving; and
Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected
area provided by the ROPS.
REQUIRED OF THE OPERATOR
1.
2.
3.
4.
5.
6.
7.
8.
9.
Securely fasten seatbelt if the tractor has a ROPS.
Where possible, avoid operating the tractor near ditches, embankments, and holes.
Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.
Stay off slopes too steep for safe operation.
Watch where you are going - especially at row ends, on roads, and around trees.
Do not permit others to ride.
Operate the tractor smoothly - no jerky turns, starts, or stops.
Hitch only to the drawbar and hitch points recommended by the tractor manufacturer.
When the tractor is stopped, set brakes securely and use park lock, if available.
Keep children away from danger all day, every day...
Equip tractors with rollover protection (ROPS) and keep all machinery
guards in place...
Please work, drive, play and live each day with care and concern for
your safety and that of your family and fellow citizens.
TURBO 120 PL 09-05
Printed U.S.A.
P/N 00778487MB

TURBO 120 MPB PUB 09-05 Rev 11-05

Transcription

Similar documents

SR15 SR10 MPB PUB 06-05 REV 04-06

REPLACMENT PARTS FOR SHORTLINE SECTION

rotary mower parts - rotary cutter parts

Flex10/Flex15 MAGNUM

FL20/FL14

SE5 Cover.p65

parts manual - Alamo Industrial