Technical data sheets

Advanced Vacuum System
materials for Vacuum processing
20
VABER INDUSTRIALE S.p.A.
Alessandro Damiano
Resp. Divisione Vuoto
+39 338 57.10.117
[email protected]
16
Te
c
hn
ic
al
da
ta
sh
ee
ts
TORINO
Strada San Mauro, 203
10156 Torino (ITALIA)
Tel. + 39 011 273.44.32
Fax + 39 011 273.17.76
www.vaber.it
[email protected]
Advanced Solutions System
www.vaber.it
Index
ADHESIVE RELEASE FILM HTR 260��������������������������������������������������������������������������������������������������������������������������������������������������������������������page 22
ADHESIVE TAPE
FTPS 180��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 29
KAP 300����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 30
AUTO TAPE DISPENSER CAT 60���������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 28
BLEEDER
AM��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 12
AR����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 13
BLEEDER RELEASE FILM DUAL FLEX����������������������������������������������������������������������������������������������������������������������������������������������������������������page 15
DRAINAGE MESH DUAL PLAY������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 14
FITTINGS AND HOSES QC 14ISOV ��������������������������������������������������������������������������������������������������������������������������������������������������������������������page 33
PEEL PLY
P6 MT85���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 23
P66 HT105�����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 24
RELEASE FILMS
LT 28 - LTF 28 holes P3 P8��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 16
MTF 30 hole P3������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 17
MT 50 - MTF 50 hole P3������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 18
ETFE HR 25���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 19
FEP HT 13������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 20
FEP HT 25������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 21
SEALANT TAPES
STLT 256���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 25
STMT 180������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 26
STHT 204 V���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 27
SPRAY TACK 5�����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 38
THREADED BUSHINGS AND PINS WITH PLATES
PBF�������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 31
PBF 316�����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 31
VACUUM BAGGING FILMS
VBA 50T����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� page 4
VBA 50S����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� page 5
VBA 50T HT���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� page 6
VBA 50T ELT�������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� page 7
VBA 70T SRG������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������ page 8
VBA 65T����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� page 9
VBA 70 SG LT����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 10
VBA 50 S LT��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 11
VACUUM GAUGE
VG 63 INOX���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 36
VG 63����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 37
VACUUM HOSES FOR AUTOCLAVE HT SS 232��������������������������������������������������������������������������������������������������������������������������������������������page 32
VALVE SUPPORTS
EV1460IR��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 34
EV1463�������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������page 35
www.vaber.it
Technical datasheet
Vacuum bagging film
VBA 50T
1)DESCRIPTION
VBA 50T is a heat-resistant flexible film of co-extruded PA / PO / PA for mouldingof epoxy matrices, suitable for polymerization in
oven and autoclaves with temperatures up to 180° C.
VBA 50T is very performing, its extreme softness and flexibility allows it to be used on all types of shapes, even complex ones.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
METHOD
Thickness μm
50 ± 15 % - *75±15%
Width
Nom. -0 +2%
Colour
Orange
Longitudinal tensile strength
43 N/mm² ± 15%
ASTM D882
Transverse tensile strength
40 N/mm² ± 15%
ASTM D882
Longitudinal elongation at break
410% ±15 %
ASTM D882
Transverse elongation at break
420% ±15 %
ASTM D882
Maximum operating temperature
+180° C
Melt temperature (DSC) pa external film
+180° to +190° C
ISO 3146
Melt temperature (DSC) po internal film
+105° to +120° C
ISO 3146
3)PACKAGING
VBA 50T is available in rolls with a standard height of 150 mm, 250 mm, 450 mm, 600 mm, 900 mm, 1200 mm, 1500 mm, 2200 mm
Length: 250 m - Tube Also available with a standard height: 2300 mm *2300 mm - Length: 200 m - Tube 4) STORAGE, SHELF-LIFE
All nylon-based films are sensitive to humidity which changes their flexibility.The rolls must be stored and used at a temperature of
about 20° C and relative humidity between 55% and 65%.
If stored properly, VBA 50 T does not expire.
The material is not hazardous for normal uses and if handled correctly by trained personnel.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
4
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Vacuum bagging film
VBA 50S
1)DESCRIPTION
VBA 50S is a heat-resistant flexible film of co-extruded PA / PO / PA for moulding of epoxy matrices, suitable for polymerization in
oven and autoclaves with temperatures up to 180° C.
VBA 50S is very performing, its extreme softness and flexibility allows it to be used on all types of shapes, even complex ones
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPRIETÀ
VALORI
METODO
Thickness µm
50 ± 15 %
Width
Nom. -0 +2 %
Colour
Orange
Longitudinal tensile strength
43 N/mm² ± 15 %
ASTM D882
Transversal tensile strength
40 N/mm² ± 15 %
ASTM D882
Longitudinal elongation at break
410 % ± 15 %
ASTM D882
Transversal elongation at break
420 % ± 15 %
ASTM D882
Melt Temperature (DSC) pa external film
180 - 190°C
ISO 3146
Melt Temperature (DSC) po internal film
105 - 120°C
ISO 3146
Maximum operating temperature
+180°C
3)PACKAGING
VBA 50S is available in rolls with a standard height of 6000 mm x 130 m - Sheet 4) STORAGE, SHELF-LIFE
All nylon-based films are sensitive to humidity which changes their flexibility. The rolls must be stored and used at a temperature of
about 20° C and relative humidity between 55% and 65%.
If stored properly, VBA 50 S does not expire.
The material is not hazardous for normal uses and if handled correctly by trained personnel.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 11.12.2014 / REVISION NO. 00 of 11.12.2014 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
5
Technical datasheet
Vacuum bagging film
VBA 50T HT
1)DESCRIPTION
VBA 50T HT is a heat-resistant flexible film of nylon 6.6 for mouldingof epoxy matrices, suitable for polymerization in oven and
autoclaves with temperatures up to 204° C.
VBA 50T HT is very powerful, its extreme softness and flexibility allows it to be used on all types of shapes, even complex ones.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
METHOD
Thickness μm
75 ± 15%
Width
Nom. -0 +2%
Colour
Green
Longitudinal tensile strength
67.4 N/mm² ± 15%
ASTM D882
Transverse tensile strength
61.6 N/mm² ± 15%
ASTM D882
Longitudinal elongation at break
450% ±15 %
ASTM D882
Transverse elongation at break
360% ±15 %
ASTM D882
Maximum operating temperature
+204° C
3)PACKAGING
VBA 50T HT is available in rolls with a standard height of 1500 mm, 2000 mm - Length: 250 m - Tube Sheet 1470 mm, 1970 mm - Length: 500 m
4) STORAGE, SHELF-LIFE
All nylon-based films are sensitive to humidity which changes their flexibility.The rolls must be stored and used at a temperature of
about 20° C and relative humidity between 55% and 65%.
If stored properly, VBA 50 T HT does not expire.
The material is not hazardous for normal uses and if handled correctly by trained personnel.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
6
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Vacuum bagging film
VBA 50T ELT
1)DESCRIPTION
VBA 50T ELT is a heat-resistant flexible film of co-extruded PA / PO / PA for mouldingof epoxy matrices, suitable for polymerization in
oven and autoclaves with temperatures up to 180° C.
VBA 50T ELT is very performing, its extreme softness and flexibility allows it to be used on all types of shapes, even complex ones.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
METHOD
Thickness μm
50 ± 15%
Width
Nom. -0 +2%
Colour
Green
Longitudinal tensile strength
64 N/mm² ± 15%
ASTM D882
Transverse tensile strength
63 N/mm² ± 15%
ASTM D882
Longitudinal elongation at break
429% ±15 %
ASTM D882
Transverse elongation at break
440% ±15 %
ASTM D882
Maximum operating temperature
+180° C
3)PACKAGING
VBA 50T ELT is available in rolls with a standard height of 1500 mm - 2080 mm - Tube 4) STORAGE, SHELF-LIFE
All nylon-based films are sensitive to humidity which changes their flexibility.The rolls must be stored and used at a temperature of
about 20° C and relative humidity between 55% and 65%.
If stored properly, VBA 50T ELT does not expire.
The material is not hazardous for normal uses and if handled correctly by trained personnel.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
7
Technical datasheet
Vacuum bagging film
VBA 70T SRG
1)DESCRIPTION
VBA 70T SRGis a gusseted film tube for self-releasing multilayer vacuum bags to be placed in direct contact with pre-impregnated
tissues for the production of pipes and hollow parts.VBA 70T SRG exhibits superior strength and works extremely well with most
types of resin systems.
The special gusset folding of VBA 70T SRG allows it to be positioned accurately inside hollow parts.
After application of the vacuum, the film expands to fit the shape of the part.This makes it very useful in applications with variations
in the inner diameter of the part.This procedure is suitable for applying internal pressure to parts with smaller diameters, where the
insertion of standard film tubes can be difficult.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
METHOD
Thickness μm
70 ± 15 %
Width
Nom. -0 +2 %
Colour
Green
Longitudinal tensile strength
50 N/mm2± 15 %
ASTM D882
Transverse tensile strength
42 N/mm2± 15 %
ASTM D882
Longitudinal elongation at break
445% ± 15 %
ASTM D882
Transverse elongation at break
350 % ± 15 %
ASTM D882
Maximum operating temperature
+170° C
3)PACKAGING
VBA 70T SRG is available in rolls with a standard heights of mm/in *80/3.15, *100/3.94, *150/5.91, 250/9.84, 300/76.2, 450/114.3 and
length of 200 m - Tube *Gusseted 4) STORAGE, SHELF-LIFE
All the nylon-based films are sensitive to humidity which changes their flexibility.The rolls must be stored and used at a temperature
of about 20° C and relative humidity between 55% and 65%.
If stored properly, VBA 70T SRG does not expire.
The material is not hazardous for normal uses and if handled correctly by trained personnel.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
8
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Vacuum bagging film
VBA 65T
1)DESCRIPTION
VBA 65 T is a heat-resistant flexible film of co-extruded PA / PO / PA for mouldingof epoxy matrices, suitable for polymerization in
oven and autoclaves with temperatures up to 180° C.
VBA 65 T is very powerful, its extreme softness and flexibility allows it to be used on all types of shapes, even complex ones.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
METHOD
Thickness μm
65 ± 15%
Width
Nom. -0 +2%
Colour
Blue
Longitudinal tensile strength
56 N/mm² ± 15%
ASTM D882
Transverse tensile strength
52 N/mm² ± 15%
ASTM D882
Longitudinal elongation at break
400% ±15 %
ASTM D882
Transverse elongation at break
410% ±15 %
ASTM D882
Maximum operating temperature
+180° C
Melt temperature (DSC) pa external film
+180° to +190° C
ISO 3146
Melt temperature (DSC) po internal film
+105° to +120° C
ISO 3146
3)PACKAGING
VBA 65 T is available in rolls with a standard height of 2700 mm x 180 m - Tube 4) STORAGE, SHELF-LIFE
All nylon-based films are sensitive to humidity which changes their flexibility.The rolls must be stored and used at a temperature of
about 20° C and relative humidity between 55% and 65%.
If stored properly, VBA 65 T does not expire.
The material is not hazardous for normal uses and if handled correctly by trained personnel.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
9
Technical datasheet
Vacuum bagging film
VBA 70 SG LT
1)DESCRIPTION
VBA 70 SG LT is a heat-resistant flexible film made from sheets of polyolefin and nylon blend, suitable for use as a vacuum bag in the
infusion processes of epoxy and vinyl-ester resins with wide and complex structures.
VBA 70 SG LT is in fact particularly resistant to the high level of manipulation and traction that occurs during the above infusion
processes.
The special composition of the sheets retains the flexibility of the bag even in low-humidity areas and periods.In this way, the VBA
70 SG LT bag guarantees perfect impregnation of the tissues and significant reduction of waste and emissions in any operating
conditions, as well as excellent aesthetic quality of the manufactured product.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
METHOD
Thickness µm
70±15% *80±15%
Length
6 m and 8 m
Colour
Light green
ASTM D882
Longitudinal tensile strength
> 35 MPa
ASTM D882
Longitudinal elongation at break
> 330 %
Maximum temperature
+120° C
3)PACKAGING
VBA 70 SG LT is available in rolls with a standard height of:
*6000 mm x 125 m - *8000 mm x 105 m - **10000 mm x 75 m - **12000 mm x 75 m**16000 mm x 70 m - Sheet Gusseted 4) STORAGE, SHELF-LIFE
VBA 70 SG LT is a hydrophilic material, and the water can act as a plasticizer.Therefore, it is important that the material is stored in
a humidity-controlled environment.
In its original condition, and in well-ventilated environments with controlled humidity and temperatures between + 5° C and + 25° C,
VBA 70 SG LT has a validity of 12 months from the packaging date.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
10
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Vacuum bagging film
VBA 50 S LT
1)DESCRIPTION
VBA 50S LT a heat-resistant flexible film made from sheets of polyolefin and nylon blend, suitable for use as a vacuum bag in the
infusion processes of epoxy and vinyl-ester resins.
VBA 50S LT is in fact particularly resistant to the high level of manipulation and traction that occurs during the pre-vacuum and
infusion processes.
The special composition of the sheets retains the flexibility of the bag even during low-humidity periods and places.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPRIETÀ
VALORI
METODO
Average thickness µm
50 ± 15%
Nominal width
-0 +2 %
Colour
Light blue
ASTM D882
Longitudinal tensile strength
> 35 MPa
ASTM D882
Longitudinal elongation at break
> 330 %
Maximum operating temperature
+120 °C
3)PACKAGING
VBA 50SLT is available in rolls with a standard height of 1800mm 400m sheet.
4) STORAGE, SHELF-LIFE
VBA 50 S LT is an hydrophilic material and water may act as a plasticizer therefore it is important to store it in an humidity controlled
area.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 18.12.2014 / REVISION NO. 00 of 18.12.2014 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
11
Technical datasheet
Bleeder
AM
1)DESCRIPTION
Bleeder AM is Needle-felt made with the finest polyester staple that makes is suitable for more complex laminated shapes with high
elongation.
The excellent ventilation makes Bleeder AM a product capable of withstanding processing in vacuum pressure autoclaves.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Material
100% Polyester fibre
Colour
White
Weight g/m²
150-180-230-300
Height
1500 mm ± 2 %
Maximum operating temperature
200° C
METHOD
3)PACKAGING
Bleeder AM is available in rolls.
4)
STORAGE, SHELF-LIFE
The rolls must be stored and used at a temperature of about 20° C and relative humidity between 55 % and 65 %.
If stored properly, Bleeder AM does not expire.
The material is not hazardous for normal uses and if handled correctly by trained personnel.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
12
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Bleeder
AR
1)DESCRIPTION
Bleeder AR is Needle-felt made with the finest polyester staple that makes it suitable for more complex laminated shapes.
The excellent ventilation makes Bleeder AR a product capable of withstanding processing in vacuum pressure autoclaves.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Material
100% Polyester fibre
Colour
White
Weight g/m²
120-150-230-300-340-450
Height
1000 -1500 mm ± 2 %
Maximum operating temperature
200° C
METHOD
3)PACKAGING
VABER Bleeder AR is available in rolls.
4)
STORAGE, SHELF-LIFE
The rolls must be stored and used at a temperature of about 20° C and relative humidity between 55% and 65%.
If stored properly, Bleeder AR does not expire.
The material is not hazardous for normal uses and if handled correctly by trained personnel.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
13
Technical datasheet
Drainage mesh
DUAL PLAY
1)DESCRIPTION
Drainage Mesh bonded with release pierced liner film recommended for infusion process based on epoxy and polyester resins.
Excellent dimensional stability and drapeable. The mesh is run-resistant.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPRIETÀ
VALORI
METODO
Weight
g 140/m² ± 5%
UNI 9401
Net material
HDPE
Net mesh
mm 1,8 x 2
Net colour
Blu
Release Liner pierced
HDPE
Fil colour
Red
Hole diameter
mm 0,8
Perforated
Nr. 5,3 holes / cm²
Film thickness
µm 30
Total weight
190 g/m² ± 5%
Maximum temperature
100°C - 212° F
3)PACKAGING
Dual Play is available in rolls height 1450 mm x 100 m length.
4) STORAGE, SHELF-LIFE
DUAL PLAY has no expiry if correctly stored in its original packaging at a temperature around 20°C and relative humidity between
55% and 65%.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 04.09.2014 / REVISION NO. 00 of 04.09.2014 / APPROVED BY: R&D / CHECKED BY: QMS
14
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Bleeder release film
DUAL FLEX
1)DESCRIPTION
Guarantees considerable time savings in application, because two products are replaced with one.
It can be used up to 3 times, thanks to the innovative fixing system between the Bleeder and FEP.
Costs are reduced by 3 times, because the chemical-physical properties allow up to 3 cycles in the autoclave.
Excellent release properties, given by the low surface tension of the release film.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Maximum temperature
200° C
FEP release film thickness μm
25
Aerator
200 g/m²
Total gram weight
230 g/m²
Stretch resistance
200%
Colour FEP
Red
Colour Aerator
White
METHOD
3)PACKAGING
Dual Flex is available in rolls 1220 wide x 98 meters long.
4)
STORAGE, SHELF-LIFE
The rolls must be stored and used at a temperature of approx. 20° C with a relative humidity between 55% and 65%.
If correctly stored, Dual Flex has a shelf life of 24 months.
The material is harmless in normal use and if handled by inexpert people.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 10.09.2014 / REVISION NO. 00 of 10.09.2014 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
15
Technical datasheet
Release film
LT 28 - LTF 28 (P3 / P8 holes)
1)DESCRIPTION
The LT 28 release film is suitable for low temperature applications - the LTF 28 version with perforations of P3 and P8 is particularly
suitable for resin infusion processes.
It has excellent release properties on all resin systems: polyester, vinylester and epoxy.
However, before using in the production process, check the chemical compatibility with the resin system used.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
METHOD
Colour
Blue
Density g/m³
0.940 (0.938-0.942)
Thickness µm
28 ± 10 %
Width mm
-0+2%
ASTM D882
Vicat softening temperature
120° C
ASTM D882
Tensile strength at break MD/TD N/mm2
35 ± 10%
ASTM D882
Elongation at Break MD/TD %
600 ± 10%
ASTM D882
No. of holes per cm² with P3 perforation
3
ISO 3146
No. of holes per cm² with P8 perforation
8
ISO 3146
Ø holes in mm with P3 perforation
0.5 to 0.8
Ø holes in mm with P8 perforation
0.5 to 0.8
3)PACKAGING
The LT 28 Release film is available in rolls with a standard height of 1500 mm and length of 250 m.
4) STORAGE, SHELF-LIFE
If stored in its original packaging at a temperature of about 20° C and relative humidity between 55% and 65%, the LT 28 Release film
does not expire.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
16
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Release film
MTF 30 hole P3
1)DESCRIPTION
The MTF 30 Release film is suitable for applications with medium temperatures.
It has excellent release properties on all types of resin systems: polyester, vinylester and epoxy.
However, before using in the production process, check the chemical compatibility with the resin system used.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
METHOD
Colour
Yellow
Density g/m³
0.900 ± 0.010
Thickness µm
30 ± 10 %
Tolerance width
-0 +2 %
Vicat softening temperature
153° C
ISO 306
Transverse/longitudinal tensile strength at break
35 N/mm² ± 10%
ASTM D 882
Transverse/longitudinal elongation at break
400 ± 10%
ASTM D 882
ASTM D1505
3)PACKAGING
The MTF 30 Release file is available in rolls with a standard height of 1500 mm and length of 250 m.
4) STORAGE, SHELF-LIFE
If stored in its original packaging at a temperature of about 20° C and relative humidity between 55% and 65%, the MTF 30 Release
film does not expire.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
17
Technical datasheet
Release film
MT 50 - MTF 50 hole P3
1)DESCRIPTION
The MT 50 Release film is suitable for applications with medium temperatures, available as MTF 50 perforated P3, P 31
It has excellent release properties on all types of resin systems: polyester, vinylester and epoxy.
However, before using in the production process, check the chemical compatibility with the resin system used.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
METHOD
Colour
Yellow
Density g/m³
0.900 ± 0.010
Thickness µm
50 ± 10 %
Tolerance width
-0 +2 %
Vicat softening temperature
153° C
ISO 306
Transverse/longitudinal tensile strength at break
35 N/mm² ± 10%
ASTM D 882
Transverse/longitudinal elongation at break
500 ± 10%
ASTM D 882
P3 diameter perforations / Ø mm
0.5 to 0.8
ISO 306
P 31 diameter perforations / Ø mm
0.5 to 0.8
ISO 306
ASTM D1505
3)PACKAGING
The MT 50 Release file is available in rolls with a standard height of 1500 mm and length of 250 m.
4) STORAGE, SHELF-LIFE
If stored in its original packaging at a temperature of about 20° C and relative humidity between 55% and 65%, the MT 50 Release film
does not expire.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
18
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Release Film
ETFE HR 25
1)DESCRIPTION
ETFE HR 25 release film is a tetrafluoroethylene.
Suited for moulding in autoclave, it maintains excellent performance even when used at high temperatures and pressure, indicated
for the majority of epoxy, phenol and polyester matrixes.
Given its low friction composition and high mechanical strength, ETFE HR 25 has excellent release power even on the most complex
shapes, giving excellent finish to the laminate.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
METHOD
Colour
Translucent sky blue
Material
ETFE
Thickness µm
25 ± 5 %
Roll width
1220 - 0 + 2 %
Tensile strength MD+TD
>40
EN ISO 527-3
Stretching resistance MD+TD
>150
EN ISO 527-3
Maximum temperature
205° C
ISO 4523
3)PACKAGING
ETFE HR 25 release film is available in rolls 1220 mm wide x 153 m long.
4) STORAGE, SHELF-LIFE
If ETFE HR 25 release film is stored in its original packaging at a temperature of approx. 20° C and relative humidity between 55% and
65%, it has unlimited shelf life.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.01.2014 / REVISION NO. 00 of 22.01.2014 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
19
Technical datasheet
Release film
FEP HT 13
1)DESCRIPTION
The FEP HT 13 Release film or Teflon-FEP® is a copolymer of tetrafluoroethylene and hexafluoropropylene.
It is suitable for autoclave moulding at high temperatures and pressures, and for using with most of the pre-pregs matrices e.g.epoxy,
phenolic and polyester.
Its low friction and low chemical reactivity allows FEP HT13 to have an excellent releasing power on even the most complex shapes
and gives an excellent finish to the laminated product.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Colour
Purple - Red
Material Type
FEP
Thickness µm
13 ± 5 %
Roll height
1220 -0+2%
Elongation at Break MD+TD
350 ± %
Maximum temperature
240
METHOD
ISO 4523
ASTM D 882
3)PACKAGING
The FEP HT13 Release film is available in rolls 1220 mm high and 186.6 m long.
4) STORAGE, SHELF-LIFE
If stored in its original packaging at a temperature of about 20° C and relative humidity between 55% and 65%, the FEP HT13 Release
film does not expire.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
20
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Release film
FEP HT 25
1)DESCRIPTION
The FEP HT 25 Release film or Teflon-FEP® is a copolymer of tetrafluoroethylene and hexafluoropropylene.
It is suitable for autoclave moulding at high temperatures and pressures, and for using with most of the pre-pregs matrices e.g.epoxy,
phenolic and polyester.
Its low friction and low chemical reactivity allows FEP HT 25 to have an excellent releasing power on even the most complex shapes
and gives an excellent finish to the laminated product.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Colour
Purple - Red
Material Type
FEP
Thickness µm
25 ± 5 %
Roll height
1220 -0+2%
Elongation at Break MD+TD
350 ± %
Maximum temperature
240° C
METHOD
ISO 4523
ASTM D 882
3)PACKAGING
The FEP HT 25Release film is available in rolls 1220 mm high and 186.6 m long.
4) STORAGE, SHELF-LIFE
If stored in its original packaging at a temperature of about 20° C and relative humidity between 55% and 65%, the FEP HT 25 Release
film does not expire.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
21
Technical datasheet
Adhesive release film
HTR 260
1)DESCRIPTION
HTR 260 is a release film with a fibreglass backing, coated in PTFE and silicone adhesive on one side. The PTFE surface has excellent
release properties that make it ideal for high temperature applications.
The product has an embossed yellow covering to protect the adhesive surface and render identification and use easier.
This film is ideal for use on flat surfaces that need excellent release properties.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Colour
Brown
Backing
PTFE / fibreglass
Adhesive
Silicone
Total thickness μm
160
Film thickness μm
120
Adhesive thickness μm
45
Max. temperature
260° C
METHOD
3)PACKAGING
HTR 260 Release Film is available in standard rolls of 1000 mm wide x 100 m long.
4) STORAGE, SHELF-LIFE
If stored in its original packaging at a temperature of approx. 20° C and a relative humidity between 55% and 65%, HTR 260 Release
Film has a shelf life of 12 months.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 08.01.2015 / REVISION NO. 00 of 08.01.2015 / APPROVED BY: R&D / CHECKED BY: QMS
22
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Peel Ply
P6 MT85
1)DESCRIPTION
The P6 MT85 Peel Ply are release fabrics specifically for professional use, they can be used in different moulding methods and resin
systems.
The use of P6 MT85release fabrics is essential for performing any kind of bonding or painting operations on laminated products.
P6 MT85Peel Ply is treated chemically to remove impurities left during weaving which can contaminate the laminate. It is thermally
fixed to withstand the temperatures indicated. In addition, the P6 MT85 Peel Ply comes with red tracers in the warp for better
identifying the positioning and orientation on the laminate.
If positioned correctly, the Vaber Peel Ply fabrics are easy to remove from the laminate.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Composition
100 % Nylon 6
Weight
85 g/m² ± 5%
Armour
Fabric
Elongation at break
≤ 20
Resistance to temperature
Max 180° C
Fixing
Fixed thermal purge
Resistance to fire
None
METHOD
3)PACKAGING
TheP6 MT85Peel Ply is available in rolls of different heights50 mm - 100 mm - 200 mm - 300 mm - 500mm - 1000 mm - 1500 mm, all the
sizes have a length of 100 m.
4) STORAGE, SHELF-LIFE
Stored in its original packaging, in a dry and well-ventilated place at temperatures between +5° C and +30° C, the P6 MT85 Peel Ply
has a life of 24 months from the manufacturing date.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
23
Technical datasheet
Peel Ply
P66 HT105
1)DESCRIPTION
The P66 HT 105 Peel Ply are release fabrics specifically for professional use, they can be used in different moulding methods and
resin systems.
The use of P66 HT 105 release fabrics is essential for performing any kind of bonding or painting operations on laminated products.
P66 HT 105 Peel Ply is treated chemically to remove impurities left during weaving which can contaminate the laminate. It is thermally
fixed to withstand the temperatures indicated. In addition, the P66 HT 105 Peel Ply comes with red tracers in the warp for better
identifying the positioning and orientation on the laminate.
If positioned correctly, the Vaber Peel Ply fabrics are easy to remove from the laminate.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Composition
100 % Nylon 6,6
Weight
105 g/m² ± 5%
Armour
Fabric
Elongation at break
30 %
Transversal elongation at break
25%
Fixing
Fixed thermal purge
Resistance to fire
None
Longitudinal tensile strength
170 daN
Transversal tensile strength
122 daN
Resistance to temperature
Max 200° C
METHOD
3)PACKAGING
The P66 HT 105 Peel Ply is available in rolls of different heights 1600 mm, all the sizes have a length of 100 m.
4) STORAGE, SHELF-LIFE
Stored in its original packaging, in a dry and well-ventilated place at temperatures between +5° C and +30° C, the P66 HT 105 Peel
Ply has a shelf-life of 24 months from the manufacturing date.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
24
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Sealant tape
STLT 256
1)DESCRIPTION
STHT 256 is a butyl sealant tape with high adhesive power formulated to seal the films to the moulds, particularly suitable for the
infusion method during the moulding of composite materials.
STHT 256 maintains the vacuum and is suitable for applications up to 120° C.
The main characteristics of the STHT 256 tape are: high adhesion, high modulus, high tensile strength and high coating performance.
This brings advantages such as easy application and removal at room temperature and leaves the surfaces of the moulds clean.
Recommended for use with Vacuum Bagging VBA 50T - VBA OS.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Colour
Grey
Application temperature
+15° C to + 40° C
Bag-to-tool serving temperature
120° C
Bag-to-bag serving temperature
130° C
Material
Modified butyl
METHOD
3)PACKAGING
STHT 256 is available in reels measuring 2 mm x 10 mm x 18 m contained in boxes of 22 pieces (for a total of 396 m).
4) STORAGE, SHELF-LIFE
Quality and characteristics of the materials remain unaltered up to 12 months from production. For correct storage, keep in a dry
place indoors, at a temperature between + 5° C and + 30° C.
The material is not hazardous for normal uses and if handled correctly by trained personnel.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
25
Technical datasheet
Sealant tapes
STMT 180
1)DESCRIPTION
STMT 180 is a butyl sealant tape with high adhesive power formulated to seal the films to the moulds, particularly suitable for
autoclaves and furnaces during the moulding of composite materials.
STMT 180 maintains the vacuum and is suitable for applications up to 180° C.
The main characteristics of the STMT 180tape are: high adhesion, high modulus, high tensile strength and high coating performance.
This brings advantages such as easy application and removal at room temperature and leaves the surfaces of the moulds clean.
Recommended for use with Vacuum Bagging VBA 50T.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Colour
Black
Application temperature
+15° C to + 40° C
Bag-to-tool serving temperature
180° C
Bag-to-bag serving temperature
190° C
Material
Modified butyl
METHOD
3)PACKAGING
STMT 180 is available in reels measuring 2 mm x 10 mm x 22,5 m, contained in boxes of 22 pieces (for a total of 495 m) and in reels
measuring 3 mm x 12 mm x 15 m, contained in boxes of 22 pieces (for a total of 330 m).
4)
STORAGE, SHELF-LIFE
The quality and characteristics of the materials remain unaltered up to 12 months from production.
For correct storage, keep in a dry place indoors, at a temperature between + 5° C and + 30° C.
The material is not hazardous for normal uses and if handled correctly by trained personnel.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
26
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Sealant tapes
STHT 204 V
1)DESCRIPTION
STHT 204 V is a butyl sealant tape with high adhesive power formulated to seal the films to the moulds, particularly suitable for
autoclaves and high-temperature furnaces.
STHT 204 V maintains the vacuum and is suitable for applications up to 204° C.
The main characteristics of the STHT 204 V tape are: high adhesion, high modulus, high tensile strength and high coating performance.
This brings advantages such as easy application and removal at room temperature and leaves the surfaces of the moulds clean.
Recommended for use with Vacuum Bagging VBA 50T - VBA 50T HT.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Colour
Black
Application temperature
+15° C to + 40° C
Bag-to-tool serving temperature
204° C
Bag-to-bag serving temperature
210° C
Material
Modified butyl
METHOD
3)PACKAGING
STHT 204 is available in reels measuring 2 mm x 10 mm x 22,5 m, contained in boxes of 22 pieces (for a total of 495 m) and in reels
measuring 3 mm x 12 mm x 15 m, contained in boxes of 22 pieces (for a total of 330 m).
4) STORAGE, SHELF-LIFE
The quality and characteristics of the materials remain unaltered up to 12 months from production. For correct storage, keep in a dry
place indoors, at a temperature between + 5° C and + 30° C.
The material is not hazardous for normal uses and if handled correctly by trained personnel.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
27
Technical datasheet
Auto Tape Dispenser
CAT 60
1)DESCRIPTION
CAT 60 is a system used for cutting adhesive tapes. It can cut up to 2 rolls at a time and save up to 6 cuts.
May be used in manual or automatic setting.
CAT 60 is a recommended tool for operators in the field of advanced composites and optimizes processing time by reducing hours
of labour.
Recommended the use with Vaber Tapes FTPS 180 and KAP 300.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPRIETÀ
VALORI
Cut width
From 6 to 60 mm
Cut length
From 5 to 999 mm (± 1mm)
Tape Diameter (ext.)
Ø 300 mm
Tape diameter (int.)
All Ø
Net weight
2,5 Kg
Voltage
AC 220V / 110V
Absorption
40 W
Dimensions
137 x 218 H 150 mm
METODO
3)PACKAGING
Avallabile as single item in carton box with electrical cable.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 08.01.2015 / REVISION NO. 00 of 08.01.2015 / APPROVED BY: R&D / CHECKED BY: QMS
28
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Adhesive tape
FTPS 180
1)DESCRIPTION
The FTPS 180adhesive tapes are made of polyester with a silicone adhesive. They are resistant to high temperatures and have high
mechanical strength. Recommendedfor processes in furnaces andautoclavesup to a temperature of 180° C.
The FTPS 180has a green opalescent colour, which allows good visibility when placed on parts or the mould; it has a height of 25 mm
and also comes in a transparent version.
The FTPS 180tapes can be used to bond metals and composites, and are suitable for vacuum bagging, thermo-coupling or for
performing masking and protection operations.The FTPS 180tapes are very easy to remove after polymerisation.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Maximum temperature
180° C
Support
Polyester
Adhesive
Silicon
Total thickness
55 µm
Film thickness
30 µm
Adhesive thickness
25 µm
Elongation at break
100%
Colour
Green / *Transparent
METHOD
3)PACKAGING
FTPS 180 is available in rolls of 66 m, and heights of 15 mm - 25 mm - *25 mm - 50 mm.
4)
STORAGE, SHELF-LIFE
The rolls must be stored and used at a temperature of about 20° C and relative humidity between 55% and 65%.
If stored properly, FTPS 180 has a life of 18 months.
The material is not hazardous for normal uses and if handled correctly by trained personnel.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
29
Technical datasheet
Adhesive tape
KAP 300
1)DESCRIPTION
KAP 300 is a polyamide tape with a polymer silicon adhesive, suitable for autoclave cycles up to 300° C.
KAP 300 is indicated for fixing release film, ventilation textiles, thermocouples, vacuum bags, etc. during polymerisation in high
temperature ovens or autoclaves.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Maximum temperature
300° C
Backing
Polyamide
Adhesive
Silicon
Total thickness μm
60
Film thickness μm
35
Adhesive thickness μm
25
Stretching resistance
40%
Colour
Amber
METHOD
3)PACKAGING
KAP 300 is available in rolls 66 m long and 25 - 50 mm wide.
4) STORAGE, SHELF-LIFE
The rolls must be stored and used at a temperature of approx. 20° C and relative humidity between 55% and 65%. If correctly stored,
KAP 300 has a shelf life of 18 months.
The material is harmless in normal use and if handled by inexpert people.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 08.01.2015 / REVISION NO. 00 of 08.01.2015 / APPROVED BY: R&D / CHECKED BY: QMS
30
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Threaded bushings and pins with plates
PBF - PBF 316
1) PBF THREADED BUSHING WITH PLATE
Product type
Threaded bushing with plate
Receiving material
Compounds, resins, carbon fibre
Production materials
Steel, stainless steel
Assembly
Co-pressed, gluing, embedding
Coating
Natural, white galvanised
2)
PBF 316 THREADED PIN WITH PLATE
Product type
Threaded pin with plate
Receiving materials
Compounds, resins, carbon fibre
Production materials
Steel, stainless steel
Assembly
Co-pressed, gluing, embedding
Coating
Natural, white galvanised
3) PACKAGING
Steel: 200 pieces
316 stainless steel: 150 pieces
4) THE TABLE BELOW GIVES INDICATIONS OF THE RECOMMENDED ADHESIVES
ADHESIVE
MA 310
MA 420
MA 830
MA 832
LAMINATES CARBON
GLASS RESIN
GELCOAT
PHENOLS
SMC
RTM
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The PC 120 Cleaner/Activator is also available.
It increases the adhesion and durability of Plexus adhesives when they are used for gluing stainless steel.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating to the application and use of our products, are given based on the present state
of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and application conditions, all the above mentioned information and instructions must
first be checked by the user according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any third-party intellectual property right.
ISSUE DATE: 08.01.2015 / REVISION NO. 00 of 08.01.2015 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
31
Technical datasheet
Vacuum hoses for autoclave
HT SS 232
1)DESCRIPTION
HT SS 232 Flexible tubing for use in autoclaves and ovens, made from stabilised silicone rubber, equipped internally with a single
stainless steel spring.
A system that guarantees top level, reliable and flexible performance in all forming processes inside autoclaves and ovens, up to a
maximum temperature of 232° C.
HT SS 232 Assembled tubing with internal and external support springs, with the joints secured by seizing on the silicone tube.
All couplings are constructed to ISOB standards.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Maximum working temperature
232° C
Maximum pressure
10 Bar
Internal diameter
7 mm
External diameter
18 mm
Final coupling
¼ inch male BSP
Materials
Silicone, Stainless steel
Colour
Green
METHOD
3)PACKAGING
HT SS 230 tubes are available in lengths of 1 - 1,5 - 2 - 2,5 - 3 - 3,5 - 4 - 4,5 - 5 - 5,5 - 6 m, other lengths on request.
4) STORAGE, SHELF-LIFE
If they are used carefully, no special storage requirements are need, and they have an unlimited life.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 20.05.2013 / REVISION NO. 00 of 20.05.2013 / APPROVED BY: R&D / CHECKED BY: QMS
32
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Fittings and hoses
QC 14ISOV
1)DESCRIPTION
The QC 14ISOV rapid couplings are male and female quick-release valves.
Our connections are available in galvanised steel for the most common applications.
Once engaged, the special spring system of the QC 14ISOV connections allows freeing the passage of air.Instead, when released,
the Viton seals of this system are capable of withstanding high temperatures and guaranteeing a secure seal.
It is recommended to use Teflon on the thread.
It can be used with the following articles: TVHT 200 - TVMT 160 - EV 14 63 and with many other products on the market.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Maximum operating temperature
180° C
Maximum pressure
10 Bar
End attachment
Female ¼ inch / Male ¼ inch
Materials
Steel Viton
Colour
White galvanized
METHOD
3)PACKAGING
The QC 14ISOV is available in individual packages.
4) STORAGE, SHELF-LIFE
If used with care, it does not require any special storage conditions, and has an unlimited life.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
33
Technical datasheet
Valve support
EV1460IR
1)DESCRIPTION
The EV 1460IR support is made entirely from Ergal, and given its special shape it aids in ventilating the laminate.
This support is widely used in the Super Car industry in producing compounds with autoclave and oven curing processes.
The EV 1460IR support is supplied with a silicon gasket with a simple manual locking system that guarantees a perfect seal.
Ideal with our articles: QC141SOV and many others currently available on the market.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Maximum working temperature
260° C
Maximum pressure
10 Bar
Base diameter
60 mm
Final coupling
Male ¼ inch
Materials
Ergal and Silicon
Colour
Green and gold
METHOD
3)PACKAGING
The EV1460IR is packed individually.
4) STORAGE, SHELF-LIFE
If used correctly it does not require any special storage conditions and has unlimited shelf life.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 4.09.2014 / REVISION NO. 00 of 4.09.2014 / APPROVED BY: R&D / CHECKED BY: QMS
34
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Valve support
EV1463
1)DESCRIPTION
The EV 1463 support is made entirely from Ergal, and given its special shape it aids in ventilating the laminate.
This support is widely used in the Super Car industry in producing compounds with autoclave and oven curing processes.
The EV 1463 support is supplied with a silicon gasket with a simple manual locking system that guarantees a perfect seal.
Ideal with our articles: QC1418V - QC14ISOV and many others currently available on the market.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Maximum working temperature
260° C
Maximum pressure
10 Bar
Base diameter
60 mm
Ring nut diameter
52 mm
Final coupling
Male ¼ inch
Materials
Ergal and Silicon
Colour
Green and gold
METHOD
3)PACKAGING
The EV1463 is packed individually.
4) STORAGE, SHELF-LIFE
If used correctly it does not require any special storage conditions and has unlimited shelf life.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
35
Technical datasheet
Vacuum gauge
VG 63 INOX
1)DESCRIPTION
The stainless steel case of the Vaber VG 63 INOX vacuum control device makes it very resistant, and allows measuring the local
vacuum in the vacuum bag, but it can be fitted on any autoclave or vacuum pump.
The Vaber VG 63 INOXgauge has a very visible measuring scale in bar, and is stabilisedin glycerine.
It is recommended to use Teflon on the thread.
To read the pressure correctly, connect the Vaber VG 63 INOXgauge to the side of the bag or a corner diagonally opposite to that of
the attachment of the vacuum rubber tube.
It can be used with the following articles: QC1418V - QC 14ISOVand with many others available on the market.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Maximum operating temperature
Ambient
Scale
0 -1 Bar
End attachment
Male ¼ inch
Main materials
Stainless steel / brass / glycerine
Colour
Steel
Dial
Ø 63
METHOD
3)PACKAGING
The VG 63 INOX comes in individual packs.
4) STORAGE, SHELF-LIFE
If used with care, it does not require any special storage conditions, and has an unlimited life.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
36
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Technical datasheet
Vacuum gauge
VG 63
1)DESCRIPTION
The vacuum gauge VG 63 is a resistant and cheap vacuum control device. It allows measuring the local vacuum in the vacuum bag,
but it can be fitted on any autoclave or vacuum pump.
The VG 63 gauge has a very visible measuring scale in bar. It is recommended to use Teflon on the thread.
To read the pressure correctly, connect the VG 63 gauge to the side of the bag or a corner diagonally opposite to that of the
attachment of the vacuum rubber tube.
It can be used with the following articles: QC1418V - QC 14ISOVand with many others available on the market.
2) CHEMICAL AND PHYSICAL CHARACTERISTICS
PROPERTY
VALUES
Maximum operating temperature
Ambient
Scale
0 -1 Bar
End attachment
Male ¼ inch
Main materials
ABS /brass
Colour
Black
Dial
Ø 63
METHOD
3)PACKAGING
The VG 63 comes in individual packs.
4) STORAGE, SHELF-LIFE
If used with care, it does not require any special storage conditions, and has an unlimited life.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 22.06.2011 / REVISION NO. 00 of 22.06.2011 / APPROVED BY: R&D / CHECKED BY: QMS
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
www.vaber.it
37
Technical datasheet
Temporary adhesive spray
SPRAY TACK 5
1)DESCRIPTION
SPRAY TACK 5 is a temporary adhesive for positioning fiberglass and carbon fibre cloths when making compound materials (in
polyester resin, vinylester and epoxy resin) using the vacuum infusion method.
SPRAY TACK 5 is formulated with raw materials that are perfectly compatible with the resins used in infusion processes, and it
dissolves in them quickly without altering the polymerization kinetics or the final mechanical properties of the product.
Even if too much adhesive is used, it does not affect the inter-laminar adhesion of the cloths.
The amount of SPRAY TACK 5 to use depends on the type of surface and the weight of the material.
Non-absorbent surfaces like Gel Coat or glass resin moulds only need a small amount of SPRAY TACK 5.
Porous and very absorbent surfaces like fibreglass cloth (biaxial, coupled) need around 1 kg per 60-100 m2. In this type of use, a spray
can covers a surface of about 15-25m2.
SPRAY TACK 5 contains a blue colorant for easier control of the amount being applied, which then disappears during the polymerization
process.
2) INSTRUCTIONS FOR USE
From a distance of about 20-30 cm apply an even layer of SPRAY TACK 5 on one or both the surfaces being coupled. The time SPRAY
TACK 5 needs to develop all its adhesive properties depends on the atmospheric conditions and the thickness of the applied layer –
generally it takes between 30 seconds and a few minutes, after which the cloth can be positioned so that it adheres perfectly to the
layer beneath, and then the operation is repeated for all the other layers.
For a few minutes after the first application, the cloth can still be repositioned.
The amount of SPRAY TACK 5 to use depends on the type of surface and the weight of the material.
Apply SPRAY TACK 5 in well ventilated areas, and wearing suitable protection equipment.
3)PACKAGING
SPRAY TACK 5 is available in 500 ml spray cans.
4) STORAGE, SHELF-LIFE
When stored in its original packaging in a dry and ventilated place, at temperatures between +15° C and +25° C, SPRAY TACK 5 has
a shelf life of 12 months from the date of production.
Warning: do not heat the spray can above 50° C.
NOTES
This information and our technical instructions (whether verbal or written or via tests), particularly those relating
to the application and use of our products, are given based on the present state of our knowledge and experience.
This does not constitute our guarantee in relation to the final results or liability arising from any legal relationship.
Considering the multiplicity of materials, supports, handling and storage conditions, as well as the production and
application conditions, all the above mentioned information and instructions must first be checked by the user
according to the specific conditions of use.
No claim or statement contained in this publication should be considered as advice or permission to violate any thirdparty intellectual property right.
ISSUE DATE: 4.09.2014 / REVISION NO. 00 of 4.09.2014 / APPROVED BY: R&D / CHECKED BY: QMS
38
www.vaber.it
VABER INDUSTRIALE S.P.A.
Strada San Mauro, 203 I - 10156 Torino (ITALY)
Tel. +39 011 273.44.32 / Fax +39 011 273.17.76 / 223.77.72
[email protected]
Vaber Industriale
TORINO
Advanced Solution System
is a mix of passion, competence,
innovation and teamwork.
Vaber team is operative
in the following fields:
• Aerospace
• Automotive
• Marine
• Transportation
• Wind and solar energy
• High Tech Design components
• Home appliances and air conditioning industries
www.vaber.it
www.servizigrafici.it
Vaber Industriale S.p.A.
is the official exclusive dealer
for Italy of: