CFD-G35 - Multiservicios de oro

Transcription

CFD-G35 - Multiservicios de oro
CFD-G35
SERVICE MANUAL
US Model
Canadian Model
E Model
Australian Model
Ver 1.4 2002. 11
Model Name Using
CD Section
Similar Mechanism
Tape Section
CD Mechanism Type
Optical Pick-up Type
Tape Transport Mechanism Type
NEW
CFD-G30
KSM-213RDP
KSS-213R
MF-V5-117
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS
Radio section
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
With 3.2-ohm loads, both channels driven
from 1 000 - 10 000 Hz; rated 2 W per
channel-minimum RMS power, with no
more than 10 % total harmonic distortion
in AC operation.
Woofer with 4-ohm loads, driven at
50 - 150 Hz; rated 4 W minimum RMS
power, with no more 10 % total harmonic
distortion in AC operation.
Frequency range
FM: 87.5 - 108 MHz
AM: 530 - 1 710 kHz
(US,Canadian,Mexican,Chilean and Peruvian
models)
: 531-1611kHz(Australian model)
: 531-1611kHz(9kHz step)(Singapore model)
: 530-1610kHz(10kHz step)(Argentina model)
Antennas
FM: Telescopic antenna
AM: Built-in ferrite bar antenna
Other specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance
of about 200 mm from the objective lens surface
on the optical pick-up block with 7 mm
aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm)
(CLV)
Number of channels
2
Frequency response
20 - 20 000 Hz +1/–2 dB
Wow and flutter
Below measurable limit
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 115 s (sec.) with Sony cassette C-60
Frequency response
TYPE I (normal): 70 - 13 000 Hz
Power requirements
For CD radio cassette-corder:
120V AC, 60 Hz:
(US,Canadian,Mexican,Chilean and Peruvian
models)
220 – 230V AC, 50 Hz:
(Argentina model)
230V AC, 50 Hz:
(Other models)
9 V DC, 6 size D (R20) batteries
For remote control:
3 V DC, 2 size AA (R6) batteries
Power consumption
AC 25 W
Battery life
For CD radio cassette-corder:
FM recording
Sony R20P: approx. 4 h
Sony alkaline LR20: approx. 19 h
Tape playback
General
Speaker
Full range: 10 cm (4 in.) dia., 3.2 Ω, cone type
(2)
Woofer: 8 cm (3 1⁄4 in.) dia., 4 Ω, cone type (1)
Outputs
Headphones jack (stereo minijack)
For 16 - 68 Ω impedance headphones
Power output
2 W + 2 W (at 3.2 Ω, 10% harmonic distortion
in DC operation)
Woofer:
6 W (at 4 Ω, 10 % harmonic distortion in DC
operation)
Sony R20P: approx. 1.5 h
Sony alkaline LR20: approx. 7 h
CD playback
Sony R20P: approx. 1.5 h
Sony alkaline LR20: approx. 3.5 h
Dimensions
Approx. 456 × 195 × 330 mm (w/h/d)
(18 × 7 3⁄4 × 13 inches) (incl. projecting parts)
Mass
Approx. 6.4 kg (14 lb. 2 oz) (incl. batteries)
Supplied accessory
AC power cord (1)
Remote control (1)
Design and specifications are subject to change
without notice.
CD RADIO CASSETTE-CORDER
9-873-631-05
Sony Corporation
2002K1600-1
© 2002.11
Personal Audio Company
Published by Sony Engineering Corporation
CFD-G35
Ver 1.3 2002. 09
TABLE OF CONTENTS
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
1. SERVICING NOTES ······················································ 3
2. GENERAL ·········································································· 4
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
3. DISASSEMBLY ································································ 5
3-1. Cabinet (Front) Assy- 1 ················································ 5
3-2. Cabinet (Front) Assy- 2 ················································ 6
3-3. CONTROL (POWER) , CONTROL (CD) ,
HEADPHONE Board ··················································· 6
3-4. Panel Assy ····································································· 7
3-5. LCD Board, Panel (Upper) ··········································· 7
3-6. Panel (Upper) Assy- 1 ··················································· 8
3-7. Panel (Upper) Assy- 2 ··················································· 8
3-8. POWER, TRANS Board ··············································· 9
3-9. TUNER Board, Duct (Upper, Lower) ··························· 9
3-10. BATT COM, BATT Board ·········································· 10
3-11. MAIN Board- 1 ··························································· 10
3-12. MAIN Board- 2 ··························································· 11
3-13. Mechanism Deck Section (MF-V5-117) ···················· 11
3-14. CD Block Section (KSM-213RDP) ···························· 12
3-15. PDW, L-R/REG Board ················································ 12
4. ADJUSTMENTS ···························································· 13
4-1. Mechanical Adjustments ··············································· 13
4-2. Electrical Adjustments ·················································· 13
5. DIAGRAMS ······································································ 17
5-1. Circuit Boards Location ·············································· 17
5-2. Block Diagrams ·························································· 18
5-3. Printed Wiring Board – TUNER Section – ················ 20
5-4. Schematic Diagram – TUNER Section – ··················· 21
5-5. Printed Wiring Board – CD Section – ························ 22
5-6. Schematic Diagram – CD Section – ··························· 23
5-7. Printed Wiring Board – TC Section – ························· 24
5-8. Schematic Diagram – TC Section – ···························· 24
5-9. Printed Wiring Board – MAIN Section – ··················· 25
5-10. Schematic Diagram – MAIN Section (1/2) – ············· 26
5-11. Schematic Diagram – MAIN Section (2/2) – ············· 27
5-12. Printed Wiring Board – AMP Section – ····················· 28
5-13. Schematic Diagram – AMP Section – ························ 29
5-14. Printed Wiring Board – CONTROL Section – ··········· 30
5-15. Schematic Diagram – CONTROL Section – ·············· 31
5-16. Printed Wiring Board – POWER Section – ················ 32
5-17. Schematic Diagram – POWER Section – ··················· 33
5-18. IC Pin Function Description ······································· 36
6. EXPLODED VIEWS ······················································ 38
6-1.
6-2.
6-3.
6-4.
6-5.
6-6.
Cabinet (Front) Section ··············································· 38
Cabinet (Rear) Section ················································ 39
Cabinet (Upper) Section ············································· 40
Mechanism Deck Section- 1 (MF-V5-117) ··············· 41
Mechanism Deck Section- 2 (MF-V5-117) ··············· 42
CD Mechanism Section (KSM-213RDP) ··················· 43
7. ELECTRICAL PARTS LIST ······································· 44
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
2
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CFD-G35
SECTION 1
SERVICING NOTES
SAFETY CHECK-OUT
After correcting the original service problem, perform the
following safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part having
a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1.
A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2.
A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3.
Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples of
a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe more than 30 cm away from the objective lens.
CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the CD lid, use
Chuck Plate Jig.
• Code number of Chuck Plate Jig : X-4918-255-1
To Exposed Metal
Parts on Set
0.15 µF
1.5 kΩ
AC
Voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
1. Press CD open knob.
2. Open the lid for CD.
3. Push on SWITCH (S801) as following figure.
4. Confirm the laser diode emission while observing the objecting
lens. When there is no emission, Auto Power Control circuit or
Optical Pick-up is broken.
Objective lens moves up and down once for the focus search.
Insert a precision
screw driver and push
SWITCH (S801)
3
CFD-G35
SECTION 2
GENERAL
This section is extracted
from instruction manual.
Location of controls
Loading a CD
Inserting a cassette
With the side you want to
play facing upward
With the labeled side up
VOLUME –, +*
MODE
TUNE –, +
DISPLAY
ENTER
MEMORY
Z PUSH
OPEN/CLOSE
u*
SOUND
x
POWER
., >
PRESET –, +
SLEEP
BAND
AUTO PRESET
i
POWER DRIVE Display
WOOFER
Remote sensor
OPR/BATT
Display
D
Total track number
Total playing time
E
Programmed track
Playing order
Remote Control
SLEEP
FUNCTION
POWER
Number buttons
About CD-Rs/CD-RWs
MODE
BAND
VOL +*, –
TUNE+, –
x
N
.,>
X
WOOFER
SOUND
*The button has a tactile dot.
4
This player can play CD-Rs/CD-RWs
recorded in the CD-DA format*, but
playback capability may vary depending on
the quality of the disc and the condition of
the recording device.
* CD-DA is the abbreviation for Compact
Disc Digital Audio. It is a recording
standard used for Audio CDs.
If you have any questions or problems
concerning your player, please consult your
nearest Sony dealer.
CFD-G35
SECTION 3
DISASSEMBLY
• The equipment can be removed using the following procedure.
Set
CABINET (FRONT) ASSY-1
(page 5)
CABINET (FRONT) ASSY-2
(page 6)
PANEL (UPPER) ASSY-1
(page 8)
PANEL (UPPER) ASSY-2
(page 8)
CONTROL (POWER), CONTROL (CD), HEADPHONE BOARD
(page 6)
LCD BOARD, PANEL (UPPER)
(page 7)
PANEL ASSY
(page 7)
MAIN BOARD-2
(page 11)
MAIN BOARD-1
(page 10)
PDW, L-R/REG BOARD
(page 12)
MECHANISM DECK SECTION (MF-V5-117)
(page 11)
POWER, TRANS BOARD
(page 9)
TUNER BOARD, DUCT (UPPER, LOWER)
(page 9)
CD BLOCK SECTION (KSM-213RDP)
(page 12)
BATT COM, BATT BOARD
(page 10)
Note : Follow the disassembly procedure in the numerical order given.
3-1. Cabinet (Front) Assy- 1
4 Open the CD lid in the
direction of the arrow.
5 screw
+BVTP 3 × 10
3 eight screws
+BVTP 3 × 14
detal view
2 two screws
+BVTP 3 × 20
1 Remove the battery case lid
in the direction of the arrow.
5
CFD-G35
3-2. Cabinet (Front) Assy- 2
2 flexible flat cable
(from MAIN board CNP804)
1 Remove the cabinet (front) assy
in the direction of the arrow.
HEADPHONE board
4 CNP391
(from PWD board KH353)
5 CNP393
(from L-R/REG board KH374)
3 flexible flat cable
(from MAIN board CNP801)
MAIN board
3-3. CONTROL (POWER) , CONTROL (CD) , HEADPHONE Board
2 CONTROL (POWER) board,
button (power)
1 two screws
+BVTP 2.6 × 10
3 screw
+BVTP 3 × 10
4 HEADPHONE board
5 two screws
+BVTP 2.6 × 10
6 CONTROL (CD) board,
button (CD)
6
CFD-G35
3-4. Panel Assy
1 screw
+BVTP 3 × 10
5 panel assy
3 flexible flat cable
(from MAIN board CNP804)
4 dlexible flat cable
(from MAIN board CNP801)
2 four screws
+BVTP 3 × 10
3-5. LCD Board, Panel (Upper)
!™ panel (upper)
7 two screws
+BVTP 2.6 × 10
8 two screws
+BVTP 2.6 × 10
5 button (PDW)
!¡ LCD board
4 button (VOL)
9 panel (front) section
6 light guide plate
(PWD)
3 flexible flat cable
(from MAIN board CNP804)
2 CONTROL (VOL) board
0 flexible flat cable
(from MAIN board CNP801)
1 six screws
+BVTP 2.6 ×10
7
CFD-G35
3-6. Panel (Upper) Assy- 1
7 Open the cassette holder assy
in the direction of the arrow.
5 Open the CD lid in the
direction of the arrow.
6 Push STOP/EJECT button.
4 Remove two harnesses
in the direction of the arrow.
2 CNP903
(from MAIN board KH301)
1 CNP1
(from MAIN board KH801)
3 Remove two harnesses
in the direction of the arrow.
3-7. Panel (Upper) Assy- 2
2 five screws
+BVTP 3 × 10
1 four screws
+BVTP 3 × 10
5 handle
4 Remove the panel (upper) assy
in the direction of the arrow.
3 Move the telescopic antenna in
the direction of the arrow.
8
CFD-G35
3-8. POWER, TRANS Board
6 five screws
+BVTP 3 × 10
1 CNP902
(from BATT board KH951)
8 POWER board,
TRANS board
4 two screws
+BVTP 3 × 10
power transformer
(T901)
2 Remove harnesses in the direction
of the arrow.
7 chassis
(trans)
3 screw
+BVTP 3 × 10
5 four screws
+BVTP 3 × 10
3-9. TUNER Board, Duct (Upper, Lower)
8 seven screws
+BVTP 2.6 × 8
0 duct (upper)
9 duct (lower)
7 two screws
+BVTP 3 × 10
2 two screws
+BVTP 3 × 10
4 TUNER board
6 bracket (woofer)
3 chassis (TU)
5 screw
+BVTP 3 × 10
1 screw
+BVTP 3 × 10
9
CFD-G35
3-10. BATT COM, BATT Board
1 CNP902
(from BATT board KH951)
2 Remove harnesses in the direction
of the arrow.
BATT board
6 BATT COM board
9 battery
terminal
8 battery terminal
5 screw
3 × 8 (DIA, 10),+WH
4 BATT board
7 three screw
+BVTP 3 × 10
3 screw
3 × 8 (DIA, 10),+WH
3-11. MAIN Board- 1
0 four screws
+BVTP 3 × 10
!¡ MAIN board
9 CNP302
3 CD door sw
(S801)
L-R/REG board
5 CNP352
4 CNP351
PDW board
8 CNP371
2 flexible flat cable
CNP802
7 CNP372
6 CNP373
1 flexible flat cable
CNP805
10
CFD-G35
3-12. MAIN Board- 2
5 MAIN board
PDW board
L-R/REG board
CNP353
CNP374
chassis (CD)
1 from TUNER board CNP1
4 from POWER board CNP903
2 from HEADPHONE board CNP391
3 from HEADPHONE board CNP393
3-13. Mechanism Deck Section (MF-V5-117)
1 flexible flat cable
(from MAIN board CNP805)
2 screw
+PTT 2 × 6
3 TC board
4 three screws
+BVTP 3 × 10
5 mechanism deck section
(MF-V5-117)
11
CFD-G35
3-14. CD Block Section (KSM-213RDP)
2 Remove solderings
from the four points.
1 flexible flat cable
(from MAIN board CNP802)
4 CD board
3 flexible flat cable
CNP701
5 four screws
2.6 × 10 (DIA, 10),+WH
6 CD block section
(KSM-213RDP)
3-15. PDW, L-R/REG Board
5 three screws
+BVTP 3 × 10
6 PDW board,
Chassis (HS, R)
2 clamp
1 screw
+BVTP 3 × 10
3 two screws
+BVTP 3 × 10
4 L-R/REG board,
Chassis (HS, L)
12
CFD-G35
SECTION 4
ADJUSTMENTS
4-1. Mechanical Adjustments
1.
2.
3.
4.
4-2. Electrical Adjustments
PRECAUTION
Clean the following parts with a denatured-alcohol-moistened
swab :
record/playback head
pinch roller
erase head
rubber belts
capstan
Demagnetize the record/playback head with a head demagnetizer. (Do not bring the head demagnetizer close to the erase
head.)
Do not use a magnetized screwdriver for the adjustments.
The adjustments should be performed with the rated power
supply voltage (9V) unless otherwise noted.
Torque Measurement
Torque
Torque Meter
Forward
CQ-102C
Forward
Back Tension
CQ-102C
Fast Forward
CQ-201B
Rewind
CQ-201B
Meter Reading
1.77 – 5.88 mN•m
(18 – 60 g•cm)
(0.25 – 0.83 oz•inch)
0.1 – 0.49 mN•m
(1.0 – 5.0 g•cm)
(0.014 – 0.069 oz•inch)
4.42 – 9.31 mN•m
(45 – 95 g•cm)
(0.62 – 1.32 oz•inch)
4.42 – 9.31 mN•m
(45 – 95 g•cm)
(0.62 – 1.32 oz•inch)
Tape Tension Measurement
Torque Meter
Meter Reading
CQ-403A
more than 60g
(more than 2.12 oz)
TAPE SECTION
0dB = 0.775V
Standard Output Level
Output terminal
HP OUT
load impedance
output signal level
32 Ω
0.25V (–10dB)
Test Tape
Type
Signal
WS-48A
3kHz, 0dB
Used for
Tape Speed Adjustment
Tape Speed Adjustment
Procedure :
Mode : Playback
digital frequency
counter
test tape
WS-48A
(3kHz, 0dB)
32Ω
set
J391 ( i )
Adjustment so than the value on the digital frequency counter is
3,000 Hz.
Adjustment Value : 3,000Hz
Standard Value : 2,940 - 3,060Hz
Frequency difference between the beginning and the end of the tape
should be within 1.5% (45Hz).
Adjustment Location : Mechanism deck
Tape speed adjustment
control inside motor
13
CFD-G35
Ver 1.1 2002. 05
0dB = 1 µV
TUNER SECTION
AM IF ADJUSTMENT
Adjust for a maximum reading on level meter.
T1
450 kHz
no mark : EXCEPT AUS,
AR, SP
( )
: AUS, SP
< >
: AR
AM Section
Function switch : AM
AM RF signal
generator
Put the lead-wire
antenna close to
the set.
AM FREQUENCY COVERAGE ADJUSTMENT
30% amplitude modulation by 400Hz
signal.
Output level : as low as possible
Frequency Display
530 kHz
(531 kHz)
<530 kHz>
Reading on Digital voltmeter
1.0 ± 0.1 V
Adjustment Part
L4
FM Section
Function switch : FM
1,710 kHz
(1,611 kHz)
<1,610 kHz>
5.3 ± 0.8V
(4.8 ± 0.8V)
<4.8± 0.8V>
<confirmation>
no mark : EXCEPT AR
< >
: AR
AM TRACKING ADJUSTMENT
FM RF signal
generator
Adjust for a maximum reading on level meter.
0.01µF
telescopic
antenna
terminal
33.75kHz frequency deviation by
1kHz signal.
Output level : as low as possible
L3
620 kHz <621kHz>
CT3
1,400 kHz <1,404 kHz>
FM IF ADJUSTMENT
Adjust for a maximum reading on level meter.
T2
10.7 MHz
FM FREQUENCY COVERAGE ADJUSTMENT
Frequency Display
Reading on Digital voltmeter
Adjustment Part
87.5 MHz
1.3 ± 0.4 V
<confirmation>
108 MHz
3.0 ± 0.3 V
L2
• Connecting Level Meter (FM and AM)
level meter
(range: 0.5–5 V ac)
32 Ω
set
Abbreviation
AR : Argentina model.
AUS : Australian model.
SP : Singapore model.
J391 ( i )
• Connecting Digital Voltmeter (FM and AM)
digital
voltmeter
100 kΩ
TP CV
• Repeat the procedures in each adjustment several times, and the
frequency coverage and tracking adjustments should be finally
done by the trimmer capacitors.
14
FM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L1
CT1
87.5 MHz
108 MHz
Adjustment Location : TUNER board (See page 16)
CFD-G35
CD SECTION
CD Test Mode
• How to put the set into CD test mode
1. Press the POWER button to turn the power on.
2. Insert the test disc (YEDS-18). (Part No. : 3-702-101-01)
(Function is set to CD.)
3. Set the CD test mode by momentary shorting both sides of
TEST- 1 on MAIN board.
4. Press the x button two times. The set is set to the CD test
mode.
(The message 80 is displayed.)
• RF Signal Reference Waveform (eye pattern)
• How to release the CD test mode
Turn the power off.
VOLT/DIV : 200mV
TIME/DIV : 500 ns
[MAIN BOARD] (Conductor side)
IC803
Focus Bias Check
1. Connect an oscilloscope between TP RF and TP VREF on
CD board.
2. Insert the test disc (YEDS-18).
3. Set the CD test mode.
4. Press the u button three times (LPC ON).
5. Confirm that the oscilloscope waveform is as shown in the figure
below. (eye pattern)
A good eye pattern means that the diamond shape (◊) in the
center of the waveform can be clearly distinguished.
6. Press the u button.(LPC OFF)
7. Perform confirmation in step 4 again.
RF level
0.85 ± 0.2 Vp-p (LPC ON)
0.95 ± 0.4 Vp-p (LPC OFF)
IC801
IC802
IC805
IC321
[CD BOARD] (Conductor side)
TP VREF
TEST-1
Traverse Waveform Check
1. Connect an oscilloscope between TP TE and TP VREF on
CD board.
2. Set the CD test mode.
3. Press the u botton to play the test disc (YEDS-18).
4. Confirm that the center of the traverse waveform will be at 0V.
5. Confirm that the peak-to-peak voltage value of the traverse
waveform meets the specification.
6. Release the CD test mode.
TP TE
TP RF
IC701
• Traverse waveform
VOLT/DIV : 200mV
TIME/DIV : 1 ms
symmetry
0V
B
A (DC voltage)
A = 0 ± 220 mV
B = 0.95 ± 0.55 Vp-p
15
CFD-G35
Adjustment Location :
[TUNER BOARD] (Component side)
L1: FM Tracking Adjustment
CT1: FM Tracking Adjustment
L3: AM Tracking Adjustment
CNP1
CT3: AM Tracking Adjustment
T2: FM IF Adjustment
T1: AM IF Adjustment
L4: AM Frequency Coverage Adjustment
L2: FM Frequency Coverage Adjustment
(Conductor side)
IC1
IC2
TP CV
AM/FM Frequency Coverage Adjustment
16
CFD-G35
SECTION 5
DIAGRAMS
Ver 1.3 2002. 09
Note on Printed Wiring Boards:
• X : parts extracted from the component side.
f
•
: internal component.
: Pattern from the side which enables seeing.
•
(The other layers' patterns are not indicated.)
5-1. Circuit Boards Location
CONTROL (VOL) board
CONTROL (POWER) board
BATT COM board
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. p: pF.
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
f
•
: internal component.
• 2 : nonflammable resistor.
• C : panel designation.
Note:
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
HEADPHONE board
•
•
•
•
•
•
•
TUNER board
LCD board
•
•
BATT board
CONTROL (CD) board
•
CD board
L-R/REG board
MAIN board
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
A : B+ Line.
H : adjustment for repair.
Total current is measured with no cassette installed.
Power voltage is dc 9 V and fed with regulated dc power
supply from battery terminal.
Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
Circled numbers refer to waveforms.
Signal path.
F : FM
f : AM
E : PB
a : REC
J : CD
Abbreviation
AR
: Argentina model.
AUS : Australian model.
CND : Canadian model.
E92 : Chilean and Peruvian model.
MX
: Mexican model.
SP
: Singapore model.
POWER board
• WAVEFORMS
– TUNER Section –
– TC Section –
1 IC2 w; (XOUT)
13.3 µs
2 Q301 collector (TAPE REC)
1.4 Vp-p
500 mV/DIV, 4 µs/DIV
3.1 Vp-p
18 µs
1 V/DIV, 10 µs/DIV
PDW board
– MAIN Section –
4 IC801 ua (XT2)
TRANS board
5 IC801 ug (X2)
TC board
3.6 Vp-p
30.5 µs
1 V/DIV, 10 µs/DIV
17
17
3.7 Vp-p
238 ns
1 V/DIV, 100 ns/DIV
– CD Section –
3 IC701 rk (XOUT)
4.2 Vp-p
59 ns
1 V/DIV, 20 ns/DIV
CFD-G35
Ver 1.3 2002. 09
5-2. Block Diagrams
MAIN Section
IC301
PRE AMP
TUNER/CD
SECTION
B
TUNER/CD
SECTION
A
L OUT
L IN
24
L-CH
RADIO
22
TAPE
BUFFER
AMP
7dB
IC371
POWER AMP
IC321
SOUND/VOLUME
R-CH
L
20
1 VIN1
OUT1 17
12
J391
3
TAPE
STBY
8
Q171
MUTE
SI
PB AMP
HEAD
SC
R-CH
VDD(SW)
14 13
5
REC AMP
26dB
L-CH
Q321
AMP
4
R-CH
R-CH
REF
REC
TAPE
LINE
6
21
15
17
Q351
BASS AGC
12
Q301
10
Q354
AGC
BIAS
OSC
S301
REC PB
3
13
CD 3.3V
(MAGNET)
SP392
SPEAKER (R-CH)
IC351
WOOFER
POWER AMP
Q322
LPF
T301
SP391
SPEAKER (L-CH)
SP393
WOOFER
5
11
STBY
8
AUDIO 6V
PB
VDD(SW)
POWER AMP +9V
REC
CNJ901
Q954
+6V REG
AU +6V
Q972
CD +6V REG
CD/RADIO +6V
Q956
+3.3V REG
CD +3.3V
VDD(SW)
Q955
D951
M
S322
MOTOR
5
S321
PLAY
D953
D957
DRY BATTERY
SIZE "D"
(IEC DESIGNATION R20)
6PCS, 9V
CND,AUS,AR,SP
VDD(5W)
D952
IC803
EEP ROM
9V
Q952
POWER
SWITCH
VDD(SW)
CD/RADIO+6V
Q951
3.3V
Q953
INV
67
36 35
65 64
34
30
77
66
TAPE
SDA
V-DATA
A-MUTE
WOOFER ON/OFF
CD
P-CON
70 XT1
71 XT2
V-CLOCK
39
REC
µ COM VDD
51
TC-PLAY
X802
32.768kHz
IC801(2/2)
SYSTEM CONTROL
IC805
RESET 76
74 X1
RMC 48
75 X2
REG CHK 49
WP
KEY-1
KEY-2
KEY-3
W-LED1
X801
4.19MHz
50
43
44
45
79
1
RESET
IC802
2
IC891
SEG0
SEG17
10 27
COM0
6
T901
D901-904
RECT
BUFFER
6
SCL
M321
CAPSTAN/REEL
MOTOR
(AC IN)
1 REMOTE 2
CONTROL
3
D807
+3.3V 2
REG
• R-CH is omitted due to same as L-CH.
D806
• Signal Path
: FM
: CD
COM3
9
: PB
VDD(SW)
TEST-1
FUNCTION
SWITCH
FUNCTION
SWITCH
S401,402
S404-408
S409-416
: REC
Q810
LED DRIVE
LCD891
LIQUID CRYSTAL
DISPLAY PANEL
D401
POWER DRIVE
WOOFER
18
18
D893
OPR/BATT
CFD-G35
TUNER/CD Section
ANT1
FM
TELESCOPIC
ANTENNA
RADIO 6V
T2
IC1
FRONT-END
IF AMP,DET,FM MPX
T2
FM IF
10
QUAD
2
MIX OUT
FM
MIX
FM RF I
RADIO 6V
CF2
4
L1
24
CF4
6
MPX
16
15
FM
MPX
L-CH
12
MUTE
A
MAIN
SECTION
R-CH
11
AM
DET
AM IF
AM IF
21
IF
BUFFER
FM
OSC
FM OSC
D2
FM
FREQUENCY
COVERAGE
D3
L3, CT3
IC2
PLL
6V
L3
FERRITE-ROD
ANTENNA
22
AM
TRACKING
MPX
T1
L2
L2
AM RF
OSC
MO/ST 13
11 AM
20
ST IND
8
BAND
7
AM
OSC
AM OSC
IFOUT
17
12 FM
19
RADIO 6V
L4
14 18 13
14 VDD
AM
MIX
CT3
L4
AM
FREQUENCY
COVERAGE
FM RF O
ST IND
FM
TRACKING
FM/AM
BUFFER
T1
RADIO 6V
CT1
FM
DET
BAND
D1
FM IF
MO/ST
L1, CT1
7
23
5
VCC1 VCC2
RADIO 6V
X1
75kHz
IC801(1/2)
SYSTEM CONTROL
20 XO
IF IN 10
19 XI
57 R-MUTE
18 LP OUT
17 LP IN
LPF
VDD(SW)
4
60 R-COUNT
DI
2
62 R-DATA
CL
3
61 R-CLK
CE 1
16 PD
OPTICAL PICK-UP
BLOCK
DO
63 R-CE
IC701
RF AMP,D/A CONV
11 VREF
VC
VCC
A
8 FIN2
B
L OUT
L OUT 42
B
MAIN
SECTION
7 FIN1
C
R OUT 45
R-CH
D
E
9 TIN1
F
10 TIN2
Q701
53 C-DO
DO 64
LD
DRIVE
LD
80 LD
GND
PD
79 PD
VR
DI 63
54 C-DI
CL 62
55 C-CLK
CE 61
56 C-CE
DRF 4
58 C-DRF
S801
FSEQ 31
46 C-FSEQ
WRQ 65
52 WRQ
Z PUSH
OPEN/CLOSE
RES 66
59 C-RES
C-DOOR 40
IC702
MOTOR/COIL DRIVE
F+
FOCUS
COIL
17 F+
F-
19
21 FDO
18 F-
T+
TRACKING
COIL
F IN
12 T+
S701
LIMIT
IN SW
CONT1 72
T IN
9
20 TDO
• R-CH is omitted due to same as L-CH.
XIN 49
T-
X701
16.93MHz
11 T-
• Signal Path
XOUT 48
M702
SLED
MOTOR
26 SL+
SL IN 25
: FM
23 SLDO
M
M701
SPINDLE M
MOTOR
: CD
27 SL2 SP+
SP IN 3
22 SPDO
1 SP-
MUTE 7
25 CONT4
19
19
CFD-G35
• See page 17 for Circuit Boards Location.
AUS,AR,SP
IC1
IC2
US,CND,E,MX
25
AUS,AR,SP
US,CND,E,MX
Ver 1.3 2002. 09
5-3. Printed Wiring Board – TUNER Section –
• Semiconductor
25
20
20
Location
Ref. No.
Location
D1
D2
D3
D10
D11
B-2
B-3
B-3
B-1
B-1
IC1
IC2
A-2
A-4
CFD-G35
Ver 1.3 2002. 09
• See page 34 for IC Block Diagrams. • See page 17 for Waveforms.
US,CND,E,MX
JC24
AUS,AR,SP
5-4. Schematic Diagram – TUNER Section –
US,CND,E,MX
C14,C15
0.022:US,CND,E,MX
0.01:AUS,AR,SP
AUS,AR,SP
21
21
CFD-G35
5-5. Printed Wiring Board – CD Section –
• See page 17 for Circuit Boards Location.
IC702
(LIMIT IN)
25
IC701
22
22
CFD-G35
5-6. Schematic Diagram – CD Section –
• See page 34,35 for IC Block Diagrams.
• See page 17 for Waveforms.
23
23
CFD-G35
Ver 1.1 2002. 05
5-7. Printed Wiring Board – TC Section –
5-8. Schematic Diagram – TC Section –
• See page 17 for Circuit Boards Location.
• See page 35 for IC Block Diagrams.
• See page 17 for Waveforms.
IC301
25
(MAGNET)
(MAGNET)
24
24
CFD-G35
Ver 1.3 2002. 09
5-9. Printed Wiring Board – MAIN Section –
• See page 17 for Circuit Boards Location.
• Semiconductor
Location
28
Ref. No.
CND,AUS,AR,SP
28
CND,AUS,AR,SP
28
CND,AUS,AR,SP
CND,AUS,AR,SP
28
EXCEPT AUS
C-1
C-4
C-1
F-5
F-5
G-5
A-4
A-4
A-4
A-3
A-3
B-3
IC321
IC801
IC802
IC803
IC805
C-3
F-4
E-4
E-4
G-3
Q321
Q322
Q810
Q951
Q952
Q953
Q954
Q955
Q956
B-2
B-1
H-3
A-4
A-4
A-4
A-3
A-3
A-2
28
32
IC321
20
IC891
IC802
24
22
IC803
IC801
IC805
Location
D320
D323
D324
D806
D807
D808
D951
D952
D953
D955
D956
D957
20
6
30
25
25
7
8
9
CFD-G35
• See page 34 for IC Block Diagrams.
EXCEPT AUS
Ver 1.3 2002. 09
5-10. Schematic Diagram – MAIN Section (1/2) –
CND,AUS,AR,SP
26
26
BUFFER
CFD-G35
Ver 1.3 2002. 09
5-11. Schematic Diagram – MAIN Section (2/2) –
• See page 36 for IC Pin Function Description.
5
4
0:US,CND,E,MX
470:SP
4.7k:AR
10k:AUS
0:EXCEPT SP
220:SP
27
27
CFD-G35
Ver 1.3 2002. 09
5-12. Printed Wiring Board – AMP Section –
• See page 17 for Circuit Boards Location.
AUS,AR,SP
C362
AUS,AR,SP
C364
AUS,AR,SP
US,CND,E,MX
C363
US,CND,E,MX
IC351
25
25
25
25
25
IC371
28
28
CFD-G35
Ver 1.3 2002. 09
US,CND,
E,MX
5-13. Schematic Diagram – AMP Section –
US,CND,
E,MX
C365
0.1
C363
0.1
AUS,AR,SP
29
AUS,AR,SP
C364 0.1 C362 0.1
29
CFD-G35
5-14. Printed Wiring Board – CONTROL Section –
• See page 17 for Circuit Boards Location.
25
SLEEP
POWER
30
30
CFD-G35
5-15. Schematic Diagram – CONTROL Section –
31
31
CFD-G35
5-16. Printed Wiring Board – POWER Section –
• See page 17 for Circuit Boards Location.
25
32
32
CFD-G35
Ver 1.3 2002. 09
5-17. Schematic Diagram – POWER Section –
*1
*1
*2
C901-904
0.022:US,CND,E,MX
0.1:AUS,AR,SP
*1
*1
* 2 F902
5A/125V:US,CND,E,MX
3.15A/250V:AUS,AR,SP
*1
33
33
CFD-G35
VSS
VDD5V
DRF
*RES
*WRQ
DO
DI
CL
CE
72 71 70
69 68
67
66
65 64 63 62 61
APC
PLL
VCEC
GATE
PD02
PD01
78 77 76 75 74 73
BUFF BUFF
LEVEL
DET
20 AM OSC
1/1OR
1/16
19 OSC OUT
ST
PCK
SLCO 1
SLCIST 2
EFMIN 3
18 ST IND
IF BUFF
FM IF
1/8
AM
DET
AF BUFF
AGC
IF REQ
17 IF OUT
4
5
6
–
FIN1
7
+
ST/MO
FM/AM
FIN2
8
15 MPX IN
VCO
DIVIDE
14 LPF2/MO-ST
DECODE
13 LPF1/BAND
TIN1
IC2 LC72137M-TLM
X OUT
X IN
LP-OUT
LP-IN
PD
VSS
VDD
MO/ST
FM-IN
AM-IN
19
18
17
16
15 14
13
12
11
RFMON 16
DATA SHIFT REGISTER
LATCH
46 RVDD
45 RCHO
44 RVSS
+
+
TBAL
LPF
+
43 LVSS
42 LCHO
41 LVSS
RUPTURE
DEFECT
–
SW
9
10
IF-IN
ADAVDD 18
ADAVSS 19
TDO
TRACK
JUMP
JITTER
DETECT
A/D
S/H
20
BOUT2
BNF1
BOUT1
OUT1
OUT2
VCC
SI
SC
18
17
16
15
14
13
Treble1 Treble2
fc=8kHz fc=8kHz
Bass2
fo=80Hz
Bass1
fo=80Hz
Logic
Vcc/2
Vcc/2
0dB-87dB
Vcc/2
Vcc/2
1
2
3
4
5
6
7
8
9
10
11
12
VIN1
VIN2
SEL2
SEL1
A1
A2
B1
B2
C1
C2
FILTER
GND
Vcc/2
50k
50k
50k
50k
50k
50k
34
34
SBCK/CONT6
BNF2
19
CONT5
TNF2
20
CONT4
TNF1
21
SPDO
SLDO
GPDAC
FDO
CAP
22
AUDIO
OUT
SERVO
PROCESSOR
RAM
IC321 BD3870FS
23
MONITOR
SIGNAL
SELECTOR
CLV, CAV
CONTROL
D/A
21 22 23 24 25 26 27
24
SUBCODE
DECODE CRC
MONI
CONT
SW
BAND
ST-IND
BAND
8
FRAME SYNC DETECT,
PROTECT INSERT,
EFM DECODE
+
LPF
UNIVERSAL
CONTROLER
7
MW/LW
NUTE
CL
–
+
JITTC 17
DO
TBAL
–
FE 13
TEC 14
TE 15
12 BIT PROGRAMBLE
DIVIDER
DI
+
49 XIN
48 XOUT
47 XVDD
CLOCK
GENERATOR
–
REFI 12
SWALLOW COUNTER
1/16. 1/17 4 BITS
6
8FS
DIGITAL
FILTER
1BIT
DAC
–
POWER
ON
RESET
1/2
5
PH
LPF
LPF
UNLOCK
DETECTOR
OCB
I/F
AUTO
ADJUST
VREF 11
PHASE DETECTOR
CHARGE PUMP
REFERENCE
DIVIDER
Surround
51 XVSS
50 FSX/16MIN
BH
–
+
FILTER
CE
+
–
9
TIN2 10
20
4
–
LEVEL SET
+
3
AGC
+
–
+
L OUT 12
2
EQ
53 EFLG
52 C2F
AF
MUTE
1
MIX
ERROR
CORRECTION
AUDIO CD
C1-1, C2-2
28 29 30
31
32 33 34 35 36 37 38 39 40
TEST
R OUT 11
54 16MOUT
DOUT
QUAD 10
57 ASDFIN
56 ASDACK
55 ASLRCK
RAM
RF
RFVDD
RFVSS
16 DET OUT
FM
DET
EXTERNAL
AUDIO IN
SLICE
LEVEL
CONTROL
MONI2
MONI3
MONI4
MONI5
(3.3V)VSS
VDD
GND2 8
SW
COMMAND
INTERFACE
60 DATA
59 DATACK
58 LRSY
FSEQ
FM IF IN 7
DRF
SERIAL
OUT
MONI1
AM IF
AM
OSC
GENERALPURPOSE
PORTS
V/*P
VCC2 5
21 FM OSC
ATTENUATION
DEEMPHASIS
FM
OSC
FM
MIX
MIX OUT 4
GATE
INTERPOLATION
MUTE
22 AM RF IN
AM
MIX
SBCK/FG
DEFECT
FM RF IN 2
AGC 9
80 79
23 VCC1
AM LOW CUT 3
AF IF IN 6
CONT2
CONT3
24 FM RF OUT
FM RF
FR
GND1 1
LDD
LDS
IC1 TA2149BN
CONT1
IC701 LC78646E-E
VVDD
PCKIST
VVSS
• IC Block Diagrams
CFD-G35
17
16
15
14
13
1k
1k
10k
MIC
IN
18
R. LIN
19
TAPE
20
R. RAD
21
LINE
REC
22
R. LO
L. RAD
23
VCC
MIC
I/EX
24
L. LO
L. LIN
IC301 TA2068N
10k
LOGIC
1k
10k
10k
MONITOR
AMP
MONITOR
AMP
–––––
TAPE
ON
ON
MUTE
LINE
MUTE
LINE
10k
10k
BUF AMP
B2
BUF AMP
B1
TAPE
10k
7dB
RADIO
RADOI
7dB
6k
–––––
TAPE
6k
15k
10k
TAPE
10k
BUF AMP
BUF AMP
A2
A1
10k
10k
10k
ON
ALC2
ALC1
NAB
AMP1
26dB
NAB
AMP2
26dB
REC
AMP1
MIC
AMP1
MUTE
10k
REC
AMP2
DET
1k
10k
9
10
11
R. RO
R. NF
R. PO
GND
7
12
MIC
NF
8
R. IN
6
REF
L. NF
L. PO
AGC
5
VCC
(FIN)
FIN
F–
24
23
22
21
20
19
18
VCC
OPIN
VCC
25
NC
VREF
26
DRIVE
BUFFER
F+
(SLIN)
17
16
15
DRIVE
BUFFER
VCC
LEVEL
SHIFT
LEVEL
SHIFT
–
+
+
–
–
+
+
–
REGULATOR VOLTAGE DETECT,
BIAS VOLTAGE DETECT,
THERMAL SHUT DOWN
LEVEL
SHIFT
DRIVER
MUTING
+
–
27
SLIN
28
SL+
SL –
BA5826FP-E2
GND
IC702
AMP
4
3
2
L. RO
1
REF
L. IN
2.1
LEVEL
SHIFT
–
+
DRIVE
BUFFER
1
2
3 4 5
6
7
8
9 10
11
12
13 14
SP –
SP +
SPIN
RST
REG-B
REGO
MUTE
GND
TIN
(TIN)
T–
T+
GND
OPOUT
DRIVE
BUFFER
35
CFD-G35
5-18. IC Pin Function Description
• IC801 µPD789478GC-8BT
System Control (MAIN Board)
Pin No.
Pin Name
I/O
1, 2
NC
—
Description
3
VLC2
I
LCD bias power supply
4
VLC1
I
LCD bias power supply
5
VLC0
I
LCD bias power supply
6 to 9
COM0 to COM3
O
LCD common signal output
10 to 27
SEG0 to SEG17
O
LCD segment signal output
28, 29
NC
—
Not used (open)
30
WOOFER ON/OFF
O
Woofer on/off control signal output
31
WOOFER 1/2
O
Woofer 1/2 signal output (not used)
32
ISS1
O
ISS-1 signal output (not used)
33
ISS2
O
ISS-2 signal output (not used)
34
A-MUTE
O
Audio muting signal output
35
SCL
O
Clock output to the EEPROM
36
SDA
I/O
37
INIT
O
Initialization setting signal output
38
AVDD
—
Power supply (A/D converter)
39
REC
I
REC signal input from the REC/PB switch (S301) “H”: record mode
40
C-DOOR
I
Detection signal input from the CD OPEN switch (S701) “L”: CD door close
41
SIMUKE
I
Destination setting signal input
42
MODE
I
Model setting signal input
43 to 45
KEY-1 to KEY-3
I
Key signal input from the function keys
46
C-FSEQ
I
CD FSEQ synchronizing signal detection signal input from the IC701
47
AVSS
—
48
RMC
I
Data input from the remote control receiver
49
REG CHK
I
Power supply voltage monitoring signal input
50
WP
I/O
51
TC-PLAY
I
TAPE PLAYsignal input from the TC PLAY switch (S321)
52
WRQ
I
CD WRQ signal input from the IC701
53
C-DO
I
CD DSP data input from the IC701
54
C-DI
O
CD DSP data output to the IC701
55
C-CLK
O
CD clock output to the IC701
56
C-CE
O
CD chip enable signal output to the IC701
57
R-MUTE
O
Radio muting signal output “L”: active
58
C-DRF
I
CD DRF signal input from the IC701
59
C-RES
O
CD system reset signal output to the IC701
60
R-COUNT
I
Radio IF count signal input from the IC2
61
R-CLK
O
Radio clock signal output to the IC2
62
R-DATA
O
Radio data output to the IC2
63
R-CE
O
Radio chip enable signal output to the IC2
64
V-CLOCK
O
Clock signal output to the sound processor (IC321)
65
V-DATA
O
Data output to the sound processor (IC321)
66
P-CON
O
Power control signal output
67
TAPE
O
TAPE function signal output to the IC301
68
VL
O
VL control signal output “L”: active
69
NC
I
Not used (connected to ground)
70
XT1
I
Sub system clock oscillator input (32.768kHz)
Not used (open)
Data input/output with the EEPROM
Ground (A/D converter)
WAKE UP reading signal output (interrupt signal in input mode)
71
XT2
O
Sub system clock oscillator output (32.768kHz)
72
VDD
—
Power supply
73
VSS
—
Ground
74
X1
I
36
Main system clock oscillator input (4.19MHz)
CFD-G35
Pin No.
Pin Name
I/O
75
X2
O
Main system clock oscillator output (4.19MHz)
Description
76
RST
I
System reset signal input
77
CD
O
CD function signal output “L”: active
78
LED CONT
O
LED control signal output (not used)
79
W-LED1
O
Woofer1 LED control signal output
80
W-LED2
O
Woofer2 LED control signal output (not used)
37
CFD-G35
SECTION 6
EXPLODED VIEWS
Ver 1.3 2002. 09
NOTE:
• -XX, -X mean standardized parts, so they may
have some differences from the original one.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
• The mechanical parts with no reference number
in the exploded views are not supplied.
CND
E92
MX
SP
• Color Indication of Appearance Parts Example:
KNOB, BALANCE (WHITE) . . . . (RED)
Â
Â
Parts color Cabinets color
• Accessories are given in the last of this parts list.
• Abbreviation
AR : Argentina model.
AUS : Australian model.
6-1. Cabinet (Front) Section
#3
: Canadian model.
: Chilean and Peruvian model.
: Mexican model.
: Singapore model.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
23
#3
12
LCD891
23
13
25
#1
14
11
#2
15
17
10
16
18
9
ba
8
23
#3
SP391
7
23
5
cabinet (rear) sectioin
#3
6 #3
#3
4
19
23
3
24
20
#4
a
23
b
23
SP393
21
#3
2
24
1
22
SP392
Ref. No.
Part No.
Description
1
1
2
2
3
3-238-215-01
X-3381-844-1
3-238-224-01
3-238-224-11
X-3381-822-1
COVER (WOOFER.943) (BLACK)
COVER (WOOFER) ASSY (SILVER)
COVER (WOOFER.COM) (BLACK)
COVER (WOOFER.COM) (SILVER)
CABINET (FRONT) SUB ASSY (BLACK) (US)
3
3
* 4
5
5
X-3381-838-1 CABINET (FRONT) SUB ASSY (BLACK)
(CND,E92,MX,AR,SP)
X-3381-841-1 CABINET (FRONT) SUB ASSY (SILVER) (AUS,SP)
1-684-458-11 CONTROL (POWER) BOARD
3-238-243-11 BUTTON (POWER) (BLACK)
3-238-243-21 BUTTON (POWER) (SILVER)
6
* 7
* 8
9
10
3-238-235-01
1-684-457-11
1-684-459-11
1-823-740-11
3-238-226-01
CHASSIS (H/J)
HEADPHONE BOARD
CONTROL (VOL) BOARD
CABLE, FLEXIBLE FLAT (26 CORE)
WINDOW (LCD) (BLACK)
10
11
11
* 12
13
3-238-226-11
X-3381-823-1
X-3381-842-1
1-684-454-11
3-238-222-11
WINDOW (LCD) (SILVER)
PANEL (FRONT) ASSY (BLACK)
PANEL (FRONT) ASSY (SILVER)
LCD BOARD
PANEL (UPPER) (BLACK)
13
14
14
38
3-238-222-21 PANEL (UPPER) (SILVER)
3-238-245-01 BUTTON (PDW) (BLACK)
3-238-245-11 BUTTON (PDW) (SILVER)
Remarks
Ref. No.
Part No.
Description
15
15
16
17
18
3-238-242-11
3-238-242-21
3-238-247-01
1-823-744-11
3-238-936-01
BUTTON (VOL) (BLACK)
BUTTON (VOL) (SILVER)
PLATE (PDW), LIGHT GUIDE
CABLE, FLEXIBLE FLAT (4 CORE)
SHEET (LCD WINDOW), ADHESIVE
19
19
20
20
* 21
3-238-250-01
3-238-250-11
3-238-244-01
3-238-244-11
1-684-460-11
LID, BATTERY CASE (BLACK)
LID, BATTERY CASE (SILVER)
BUTTON (CD) (BLACK)
BUTTON (CD) (SILVER)
CONTROL (CD) BOARD
22
23
24
25
LCD891
3-040-916-01
4-951-620-11
4-951-620-01
3-238-938-01
1-804-640-11
CUSHION (FOOT) FRONT
SCREW (2.6X10), +BVTP
SCREW (2.6X8), +BVTP
HOLDER, LCD
DISPLAY PANEL, LIQUID CRYSTAL
SP391
SP391
SP392
SP392
SP393
1-825-029-11
1-825-159-11
1-825-029-11
1-825-159-11
1-825-030-11
SPEAKER (10cm) (BLACK)
SPEAKER (10cm) (SILVER)
SPEAKER (10cm) (BLACK)
SPEAKER (10cm) (SILVER)
SPEAKER (8cm) (WOOFER)
#1
#2
#3
#4
7-685-651-79
7-685-649-79
7-685-647-79
7-685-783-09
SCREW +BVTP 3X20 TYPE2 N-S
SCREW +BVTP 3X14 TYPE2 N-S
SCREW +BVTP 3X10 TYPE2 N-S
SCREW +PTT 2X6 (S)
Remarks
CFD-G35
Ver 1.3 2002. 09
6-2. Cabinet (Rear) Section
60
59
58
57
#5
#3
63
#3
#3
#3
#3
#3
ANT1
b
cabinet (upper)
section
T901
55
56
not
supplied
74
a
61
F902
62
#6
54
#3
#3
53
64
52
66
65
not
supplied
#3
#3
51
a
#3
b
72
70
68
67
#3
Part No.
Description
51
51
52
52
53
3-238-229-01
3-238-229-11
3-238-228-01
3-238-228-11
4-951-620-01
54
* 55
56
57
57
72
69
#3
Ref. No.
71
not
supplied
#3
71
Remarks
Ref. No.
Part No.
Description
DUCT (LOWER) (BLACK)
DUCT (LOWER) (SILVER)
DUCT (UPPER) (BLACK)
DUCT (UPPER) (SILVER)
SCREW (2.6X8), +BVTP
63
* 64
65
66
* 67
3-238-249-11
1-684-462-11
3-238-136-01
3-238-214-01
1-684-453-11
HANDLE (SILVER)
BATT COM BOARD
TERMINAL (+,–), BATTERY
TERMINAL (+,–), BATTERY
BATT BOARD
3-238-230-01
1-684-451-11
3-238-934-01
X-3381-821-1
X-3381-840-1
CHASSIS (TRANS)
POWER BOARD
SPRING (CASSETTE)
HOLDER ASSY, CASSETTE (BLACK)
HOLDER ASSY, CASSETTE (SILVER)
* 68
* 68
69
70
71
A-3323-779-A
A-3323-815-A
3-238-231-01
3-238-134-01
3-238-135-01
TUNER BOARD ,COMPLETE (US,CND,E92,MX)
TUNER BOARD ,COMPLETE (AUS,AR,SP)
CHASSIS (TU)
TERMINAL, ANTENNA
TERMINAL (–), BATTERY
58
59
60
60
61
1-452-899-11
3-019-395-01
3-238-219-11
3-238-219-31
3-238-935-01
MAGNET
PLATE, CHUCKING
LID, CD (BLACK)
LID, CD (SILVER)
SPRING (CD)
72
* 74
ANT1
0 F902
0 F902
4-960-167-01
1-684-452-11
1-501-883-21
1-532-465-11
1-576-109-11
SCREW (3X8) (DIA. 10), +WH
TRANS BOARD
ANTENNA, TELESCOPIC
FUSE, TIME LAG 3.15A/250V(AUS,AR,SP)
FUSE 5A/125V(US,CND,E92,MX)
62
62
62
62
63
3-238-217-31
3-238-217-41
3-238-217-51
3-238-217-71
3-238-249-01
CABINET (REAR) (BLACK) (US)
CABINET (REAR) (BLACK) (CND,E92,MX)
CABINET (REAR) (BLACK) (AR,SP)
CABINET (REAR) (SILVER) (AUS,SP)
HANDLE (BLACK)
0 T901
0 T901
#3
#5
#6
1-437-644-11
1-437-645-11
7-685-647-79
7-685-533-19
7-682-548-04
TRANSFORMER, POWER(US,CND,E92,MX)
TRANSFORMER, POWER(AUS,AR,SP)
SCREW +BVTP 3X10 TYPE2 N-S
SCREW +BTP 2.6X6 TYPE2 N-S
SCREW +B 3X8
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Remarks
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
39
CFD-G35
Ver 1.3 2002. 09
6-3. Cabinet (Upper) Section
S801
114
112
#3
115
mechanism
deck section-1
(MF-V5-117)
106
129
127
107
108
116
109
110
section
(KSM-213RDP)
130
105
111
131
#3
not
supplied
128
#3
117 CD mechanism
#3
124
S321
#6
132
128
#6
119
126
#7
#3
121
113
#6
102
128
122
#3
#3
not
supplied
101
125
118
120
not
supplied
#3
103
132
#3
132
#3
123
#3
#3
#3
Ref. No.
Part No.
Description
* 101
102
103
105
106
A-3178-395-A
3-238-232-01
1-757-778-11
3-031-560-01
3-238-236-01
106
107
107
108
108
not
supplied
#3
Ref. No.
Part No.
Description
L-R/REG BOARD, COMPLETE
CHASSIS (HS.L)
CABLE, FLEXIBLE FLAT (11 CORE)
SHAFT (MD)
BUTTON (REC) (BLACK)
118
119
* 120
* 120
121
3-931-379-21
3-931-379-31
A-3178-396-A
A-3178-479-A
3-238-233-01
RUBBER, VIBRATION PROOF
RUBBER, VIBRATION PROOF
PDW BOARD,COMPLETE (US,CND,E92,MX)
PDW BOARD,COMPLETE (AUS,AR,SP)
CHASSIS (HS.R)
3-238-236-11
3-238-237-01
3-238-237-11
3-238-238-01
3-238-238-11
BUTTON (REC) (SILVER)
BUTTON (PLAY) (BLACK)
BUTTON (PLAY) (SILVER)
BUTTON (REW) (BLACK)
BUTTON (REW) (SILVER)
*
*
*
*
122
122
122
122
123
A-3178-397-A
A-3178-469-A
A-3178-471-A
A-3178-472-A
1-823-742-11
MAIN BOARD,COMPLETE (US,E92,MX)
MAIN BOARD,COMPLETE (CND)
MAIN BOARD,COMPLETE (AR)
MAIN BOARD,COMPLETE (SP)
WIRE (FLAT TYPE) (14 CORE)
109
109
110
110
111
3-238-239-01
3-238-239-11
3-238-240-01
3-238-240-11
3-238-241-01
BUTTON (FF) (BLACK)
BUTTON (FF) (SILVER)
BUTTON (STOP/EJECT) (BLACK)
BUTTON (STOP/EJECT) (SILVER)
BUTTON (PAUSE) (BLACK)
124
* 125
126
127
128
1-757-689-11
A-3178-122-A
A-3178-403-A
3-222-727-01
3-921-725-01
CABLE, FLEXIBLE FLAT (16 CORE)
CD BOARD, COMPLETE
TC BOARD, COMPLETE
LEVER (REC)
SCREW (2.6X10), +PWH
111
112
113
114
115
3-238-241-11
3-047-468-01
4-960-167-01
3-232-770-01
3-238-218-21
BUTTON (PAUSE) (SILVER)
DAMPER
SCREW (3X8) (DIA. 10), +WH
STOPPER (CD)
CABINET (UPPER) (BLACK) (US,AR)
129
130
131
132
S321
3-047-468-11
4-951-620-01
3-222-726-01
3-703-150-11
1-771-686-11
DAMPER
SCREW (2.6X8), +BVTP
CHASSIS (TC)
CLAMP
SWITCH, LEAF (PLAY SW)
115
115
116
117
3-238-218-31
3-238-218-41
3-238-234-01
3-923-736-01
CABINET (UPPER) (BLACK) (CND,E92,MX,SP)
CABINET (UPPER) (SILVER) (AUS,SP)
CHASSIS (CD)
COVER, CD
S801
#3
#6
#7
1-692-960-11
7-685-647-79
7-682-548-04
7-685-853-04
SWITCH, PUSH (1 KEY) (ZPUSH OPEN/CLOSE)
SCREW +BVTP 3X10 TYPE2 N-S
SCREW +B 3X8
SCREW +BVTT 2X6 (S)
40
Remarks
113
Remarks
CFD-G35
6-4. Mechanism Deck Section- 1 (MF-V5-117)
HRP301
159
170
HE301
158
160
161
162
169
168
163
157
155
156
167
164
165
154
153
166
151
mechanism deck section-2
(MF-V5-117)
152
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
151
152
153
154
155
3-933-010-01
3-933-025-01
3-040-857-01
3-933-024-01
3-933-019-01
SPRING (S/P), TORSION
SPRING (P), TORSION
LEVER (P)
ROLLER, PINCH
SPRING (F/R), TORSION
Remarks
* 162
* 163
164
* 165
* 166
3-008-587-01
3-008-591-01
3-933-004-01
3-933-021-01
3-933-006-01
SLIDER (STOP)
SLIDER (PAUSE)
CLAW, REEL
SLIDER (FRP)
SLIDER (EJECT)
156
157
158
159
* 160
3-933-028-01
3-933-016-01
3-008-590-01
3-008-592-23
3-008-588-01
SPRING (FWD), TORSION
GEAR (S REEL)
SLIDER (REC)
BASE (H), HEAD
SLIDER (REW)
167
168
169
* 170
HE301
3-934-833-01
3-022-794-02
3-933-007-01
3-012-114-01
1-543-876-11
SPRING (FRP)
SPRING (BT)
PLATE, LOCK
LEVER (FR)
HEAD (ERASE)
* 161
3-008-589-13 SLIDER (FF)
Remarks
HRP301 1-500-691-11 HEAD,MAGNETIC(RECORD/PLAYBACK)
41
CFD-G35
6-5. Mechanism Deck Section- 2 (MF-V5-117)
207
206
219
209
208
205
204
210
216
203
S322
211
218
212
M321
213
217
214
#10
202
Ref. No.
215
201
Part No.
Description
Part No.
Description
201
202
203
204
205
3-933-029-01
3-933-182-01
3-932-995-01
X-3371-667-1
3-932-997-01
LEVER, ERASING PREVENTION
SPRING, CASSETTE
GEAR (MID)
CLUTCH ASSY
GEAR (CAM)
213
214
215
216
217
3-932-993-01
3-343-358-01
3-933-005-01
3-939-383-02
3-937-760-01
CHASSIS, OUTSERT
RING, RETAINING
SPRING (CAM), COMPRESSION
SPRING, COMPRESSION
SPRING (GROUND), COMPRESSION
* 206
207
208
209
210
3-932-999-01
3-932-998-01
3-009-648-01
3-936-438-01
X-3373-572-1
SLIDER (SW)
SPRING (GROUND), TORSION
LEVER (S.OFF)
LEVER (K)
REEL ASSY (N), T
218
219
M321
S322
#10
3-934-336-01
3-009-650-02
A-3320-446-A
1-762-679-11
7-621-770-87
BEARING
SPRING (K), COMPRESSION
MOTOR ASSY (CAPSTAN/REEL)
SWITCH, LEAF (MOTOR SW)
SCREW +B 2.6X5
211
212
42
3-933-020-11 BELT
X-3377-877-3 FLYWHEEL ASSY
Remarks
Ref. No.
Remarks
CFD-G35
Ver 1.3 2002. 09
6-6. CD Mechanism Section (KSM-213RDP)
251
252
254
253
256
255
260
258
(including M702)
259
M702
M701
Ref. No.
Part No.
Description
0 251
* 252
* 253
* 254
255
8-820-161-02
2-169-065-01
2-169-385-01
2-647-408-02
2-169-388-01
OPTICAL PICK-UP KSS-213R
GEAR (A)
SPRING, SLED
GEAR (B)
TAPPING (M2), +PWB
Remarks
Ref. No.
Part No.
Description
256
258
259
* 260
M701
3-713-786-51
X-2162-707-1
2-626-908-01
2-169-384-01
X-2162-712-1
SCREW (M2 x 3)
CHASSIS ASSY, (RDP) (RP) MOTOR (SPINDLE)
SHAFT, SLED
SHAFT (S), GEAR
GEAR ASSY (R) (RP), MOTOR (SLED)
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Remarks
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
43
CFD-G35
Ver 1.3 2002. 09
BATT
BATT COM
CD
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX, -X mean standardized parts, so they may
have some difference from the original one.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
• CAPACITORS:
uF: µF
Ref. No.
Part No.
Description
*
1-684-453-11 BATT BOARD
***********
SECTION 7
ELECTRICAL PARTS LIST
•
Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• COILS
uH: µH
• Abbreviation
AR : Argentina model.
AUS : Australian model.
Remarks Ref. No.
Part No.
3-238-135-01 TERMINAL (-), BATTERY
CND
E92
MX
SP
: Canadian model.
: Chilean and Peruvian model.
: Mexican model.
: Singapore model.
When indicating parts by reference number,
please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
Description
Remarks
C739
C740
C741
C742
C743
1-164-156-11
1-126-935-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
470uF
0.1uF
0.1uF
0.1uF
25V
20.00% 10V
25V
25V
25V
C744
C745
C746
C747
C750
1-164-156-11
1-164-156-11
1-104-665-11
1-104-665-11
1-104-665-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
0.1uF
0.1uF
100uF
100uF
100uF
25V
25V
20.00% 10V
20.00% 10V
20.00% 10V
C751
C754
C755
1-164-156-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
0.1uF
0.01uF
0.01uF
10%
10%
25V
25V
25V
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
< CABLE HOLDER >
* KH941 1-565-385-11 HOLDER, CABLE 4P
**************************************************************
1-684-462-11 BATT COM BOARD
***************
*
3-238-135-01 TERMINAL (-), BATTERY
**************************************************************
A-3178-122-A CD BOARD, COMPLETE
*******************
*
< CONNECTOR >
CNP701 1-770-168-11 CONNECTOR, FFC/FPC 16P
* CNP702 1-784-736-11 CONNECTOR, FFC 14P
< CAPACITOR >
C701
C702
C703
C704
C705
1-162-964-11
1-126-947-11
1-107-826-11
1-162-919-11
1-162-968-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
47uF
0.1uF
22PF
0.0047uF
10%
20.00%
10.00%
5%
10%
C706
C707
C708
C709
C711
1-126-960-11
1-115-156-11
1-162-927-11
1-164-156-11
1-162-974-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
100PF
0.1uF
0.01uF
20.00% 50V
10V
5%
50V
25V
50V
C716
C717
C720
C721
C722
1-162-974-11
1-163-021-91
1-162-919-11
1-162-919-11
1-162-919-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
22PF
22PF
22PF
50V
10.00% 50V
5%
50V
5%
50V
5%
50V
C723
C724
C725
C726
C727
1-162-974-11
1-162-919-11
1-162-964-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
22PF
0.001uF
0.001uF
0.001uF
5%
10%
10%
10%
50V
50V
50V
50V
50V
C728
C729
C730
C731
C732
1-165-176-11
1-125-837-91
1-107-826-11
1-165-176-11
1-104-665-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.047uF
1uF
0.1uF
0.047uF
100uF
10.00%
10%
10.00%
10.00%
20.00%
16V
6.3V
16V
16V
10V
C733
C734
C735
C736
C738
1-104-665-11
1-162-968-11
1-126-916-11
1-162-968-11
1-164-156-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
100uF
0.0047uF
1000uF
0.0047uF
0.1uF
20.00%
10%
20.00%
10%
10V
50V
6.3V
50V
25V
44
50V
10V
16V
50V
50V
< FERRITE BEAD >
FB701
1-469-701-21 INDUCTOR
0UH
< IC >
IC701
IC702
6-701-796-01 IC LC78646E-E
6-701-787-11 IC BA5826FP-E2
< JUMPER RESISTOR >
JC701
JC702
JC703
JC704
1-216-864-11
1-216-864-11
1-216-864-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
1K
< COIL >
L706
1-414-445-11 FERRITE
0uH
< TRANSISTOR >
Q701
8-729-054-57 TRANSISTOR
KTN2907AS-RTK
< RESISTOR >
R701
R702
R703
R704
R705
1-216-841-11
1-216-835-11
1-216-835-11
1-216-835-11
1-216-835-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
15K
15K
15K
15K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
CFD-G35
Ver 1.1 2002. 05
CD
Ref. No.
CONTROL (CD)
CONTROL (POWER)
CONTROL (VOL)
Part No.
Description
Remarks
Ref. No.
Part No.
R706
R707
R708
R709
R710
1-216-841-11
1-216-797-11
1-216-833-11
1-216-837-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
10
10K
22K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
*
1-684-458-11 CONTROL (POWER) BOARD
***********************
Description
Remarks
R711
R712
R714
R715
R716
1-216-815-11
1-216-809-11
1-216-811-11
1-216-811-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
330
100
150
150
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R717
R718
R719
R720
R721
1-216-821-11
1-216-821-11
1-216-809-11
1-216-809-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
100
100
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R722
R723
R724
R725
R726
1-216-809-11
1-216-809-11
1-216-841-11
1-216-819-11
1-216-819-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
47K
680
680
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R727
R728
R729
R730
R731
1-216-825-11
1-216-833-11
1-216-813-11
1-216-821-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
10K
220
1K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R732
R741
R743
R744
1-216-841-11
1-218-867-11
1-218-867-11
1-216-845-11
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
47K
6.8K
6.8K
100K
5%
5%
5%
5%
1/16W
1/10W
1/10W
1/16W
< CABLE HOLDER >
* KH404
1-565-384-11 HOLDER, CABLE 3P
< RESISTOR >
R401
R402
R403
1-216-817-11 METAL CHIP
1-216-813-11 METAL CHIP
1-216-821-11 METAL CHIP
470
220
1K
5%
5%
5%
1/16W
1/16W
1/16W
< SWITCH >
S401
1-771-349-21 SWITCH, TACT (POWER)
S402
1-771-349-21 SWITCH, TACT (SLEEP)
**************************************************************
1-684-459-11 CONTROL (VOL) BOARD
********************
*
< CONNECTOR >
CNP401 1-784-726-11 CONNECTOR, FFC 4P
< DIODE >
D401
D401
8-719-085-33 DIODE SLI-343URCT32WST
(POWER DRIVE WOOFER)
(only for the cabinet color is black)
6-500-284-01 DIODE DB3804X(POWER DRIVE WOOFER)
(only for the cabinet color is silver)
< CABLE HOLDER >
< SWITCH >
* KH402
S701
1-565-386-11 HOLDER, CABLE 5P
1-571-936-11 SWITCH, LEAF (LIMITIN)
< RESISTOR >
< VIBRATOR >
X701
1-781-801-21 VIBRATOR, CERAMIC 16.93MHz
**************************************************************
1-684-460-11 CONTROL (CD) BOARD
*******************
*
< CABLE HOLDER >
* KH403
1-573-287-11 HOLDER, CABLE 2P
R411
R412
R413
R414
R415
1-216-817-11
1-216-813-11
1-216-821-11
1-216-821-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
220
1K
1K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R416
R417
R418
R419
R420
1-216-825-11
1-216-821-11
1-216-829-11
1-216-825-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
1K
4.7K
2.2K
22K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< RESISTOR >
< SWITCH >
R404
R405
R406
R407
R408
1-216-821-11
1-216-825-11
1-216-825-11
1-216-821-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
2.2K
2.2K
1K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R409
R410
1-216-825-11 METAL CHIP
1-216-837-11 METAL CHIP
2.2K
22K
5%
5%
1/16W
1/16W
< SWITCH >
S409
S410
S411
S412
S413
1-771-349-21
1-771-349-21
1-771-349-21
1-771-349-21
1-771-349-21
SWITCH, TACT (MODE)
SWITCH, TACT (TUNE+)
SWITCH, TACT (TUNE-)
SWITCH, TACT (SOUND)
SWITCH, TACT (DISPLAY/ENTER/MEMORY)
S414
1-771-349-21 SWITCH, TACT (VOLUME-)
S415
1-771-349-21 SWITCH, TACT (VOLUME+)
S416
1-771-349-21 SWITCH, TACT (POWER DRIVE WOOFER)
**************************************************************
S404
1-771-349-21 SWITCH, TACT (u)
S405
1-771-349-21 SWITCH, TACT (x)
S406
1-771-349-21 SWITCH, TACT (AUTO PRESET/BAND)
S407
1-771-349-21 SWITCH, TACT (PRESET+ >)
S408
1-771-349-21 SWITCH, TACT (PRESET– .)
**************************************************************
45
CFD-G35
Ver 1.3 2002. 09
HEADPHONE
L-R/REG
Ref. No.
Part No.
*
1-684-457-11 HEADPHONE BOARD
*****************
LCD
Description
MAIN
Remarks
Ref. No.
CNP391
CNP392
CNP393
CNP394
1-785-657-21
1-785-656-21
1-785-656-11
1-785-656-11
PIN, CONNECTOR (PC BOARD) 5P
PIN, CONNECTOR (PC BOARD) 4P
PIN, CONNECTOR (PC BOARD) 4P
PIN, CONNECTOR (PC BOARD) 4P
< JACK >
J391
1-794-016-11 JACK (i)
< RESISTOR >
R191
1-247-807-31 CARBON
100
5%
1/4W
R192
1-216-821-11 METAL CHIP
1K
5%
1/16W
R291
1-247-807-31 CARBON
100
5%
1/4W
R292
1-216-821-11 METAL CHIP
1K
5%
1/16W
**************************************************************
Remarks
R171
R172
R173
R174
R175
1-216-841-11
1-216-837-11
1-216-825-11
1-216-833-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
22K
2.2K
10K
220
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R176
R177
R271
R272
R273
1-216-805-11
1-249-389-11
1-216-841-11
1-216-837-11
1-216-825-11
METAL CHIP
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
47
4.7
47K
22K
2.2K
5%
5%
5%
5%
5%
1/16W
1/4W F
1/16W
1/16W
1/16W
R274
1-216-833-11 METAL CHIP
10K
5%
1/16W
R275
1-216-813-11 METAL CHIP
220
5%
1/16W
R276
1-216-805-11 METAL CHIP
47
5%
1/16W
R277
1-249-389-11 CARBON
4.7
5%
1/4W F
R371
1-216-833-11 METAL CHIP
10K
5%
1/16W
**************************************************************
1-684-454-11 LCD BOARD
**********
*
A-3178-395-A L-R/REG BOARD, COMPLETE
************************
*
Description
< RESISTOR >
< CONNECTOR >
*
*
*
*
Part No.
3-238-938-01 HOLDER, LCD
3-238-232-01
3-703-150-11
4-960-167-01
7-685-647-79
CHASSIS (HS.L)
CLAMP
SCREW (3X8) (DIA. 10), +WH
SCREW +BVTP 3X10 TYPE2 N-S
< CAPACITOR >
C891
1-164-227-11 CERAMIC CHIP
0.022uF
10%
25V
< CONNECTOR >
< CAPACITOR >
C171
C172
C173
C174
C175
1-126-947-11
1-162-964-11
1-126-947-11
1-126-926-11
1-136-165-00
ELECT
CERAMIC CHIP
ELECT
ELECT
FILM
47uF
0.001uF
47uF
1000uF
0.1uF
20.00%
10%
20.00%
20.00%
5.00%
10V
50V
10V
10V
50V
C271
C272
C273
C274
C275
1-126-947-11
1-162-964-11
1-126-947-11
1-126-926-11
1-136-165-00
ELECT
CERAMIC CHIP
ELECT
ELECT
FILM
47uF
0.001uF
47uF
1000uF
0.1uF
20.00%
10%
20.00%
20.00%
5.00%
10V
50V
10V
10V
50V
C371
C972
1-104-665-11 ELECT
1-164-156-11 CERAMIC CHIP
100uF
0.1uF
20.00% 10V
25V
* CNP891 1-784-748-11 CONNECTOR, FFC 26P
< DIODE >
D893
8-719-059-97 DIODE L-34HD (OPR/BATT)
< IC >
IC891
8-749-014-88 IC SPS-440-E (g)
< LIQUID CRYSTAL DISPLAY >
LCD891 1-804-640-11 DISPLAY PANEL, LIQUID CRYSTAL
< RESISTOR >
< CONNECTOR >
* CNP371 1-785-655-21 PIN, CONNECTOR (PC BOARD) 3P
* CNP372 1-785-655-11 PIN, CONNECTOR (PC BOARD) 3P
* CNP373 1-785-657-11 PIN, CONNECTOR (PC BOARD) 5P
< IC >
IC371
* KH374
8-759-426-51 IC BA5417
< CABLE HOLDER >
*
1-565-385-11 HOLDER, CABLE 4P
*
8-729-281-53 TRANSISTOR
8-729-281-53 TRANSISTOR
8-729-037-08 TRANSISTOR
A-3178-397-A MAIN BOARD, COMPLETE (US,E92,MX)
*********************
A-3178-469-A MAIN BOARD, COMPLETE (CND)
*********************
A-3178-471-A MAIN BOARD, COMPLETE (AR)
*********************
A-3178-472-A MAIN BOARD, COMPLETE (SP)
*********************
A-3178-473-A MAIN BOARD, COMPLETE (AUS)
*********************
< CAPACITOR >
*
< TRANSISTOR >
Q171
Q271
Q972
R891
1-216-841-11 METAL CHIP
47K
5%
1/16W
R892
1-216-813-11 METAL CHIP
220
5%
1/16W
R893
1-216-817-11 METAL CHIP
470
5%
1/16W
R894
1-216-813-11 METAL CHIP
220
5%
1/16W
R895
1-216-817-11 METAL CHIP
470
5%
1/16W
**************************************************************
*
2SC1815GR-TPE2
2SC1815GR-TPE2
KTD2058Y
*
C123
C124
C126
46
1-126-961-11 ELECT
1-162-964-11 CERAMIC CHIP
1-126-961-11 ELECT
2.2uF
0.001uF
2.2uF
20.00% 50V
10%
50V
20.00% 50V
CFD-G35
Ver 1.3 2002. 09
MAIN
Ref. No.
Part No.
Description
Part No.
Description
C127
C129
C130
C131
C132
1-162-966-11
1-107-826-11
1-107-826-11
1-126-960-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.0022uF
0.1uF
0.1uF
1uF
100PF
10%
10.00%
10.00%
20.00%
5%
50V
16V
16V
50V
50V
Remarks
Ref. No.
C841
C846
C953
C955
C957
1-162-927-11
1-107-826-11
1-164-227-11
1-164-227-11
1-126-934-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
100PF
0.1uF
0.022uF
0.022uF
220uF
5%
10.00%
10%
10%
20.00%
50V
16V
25V
25V
10V
Remarks
C223
C224
C226
C227
C229
1-126-961-11
1-162-964-11
1-126-961-11
1-162-966-11
1-107-826-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
2.2uF
0.001uF
2.2uF
0.0022uF
0.1uF
20.00%
10%
20.00%
10%
10.00%
50V
50V
50V
50V
16V
C958
C959
C960
C961
1-164-227-11
1-164-227-11
1-126-934-11
1-126-934-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.022uF
0.022uF
220uF
220uF
10%
10%
20.00%
20.00%
25V
25V
10V
10V
C230
C231
C232
C321
1-107-826-11
1-126-960-11
1-162-927-11
1-162-962-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1uF
1uF
100PF
470PF
C322
1-162-964-11 CERAMIC CHIP
0.001uF
10.00% 16V
20.00% 50V
5%
50V
10%
50V
(EXCEPT AUS)
10%
50V
C323
C324
C325
C326
C327
1-126-959-11
1-126-947-11
1-104-665-11
1-165-176-11
1-164-227-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.47uF
47uF
100uF
0.047uF
0.022uF
20.00%
20.00%
20.00%
10.00%
10%
50V
10V
10V
16V
25V
C333
C334
C336
C337
C338
1-162-970-11
1-164-227-11
1-126-947-11
1-126-960-11
1-126-964-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
0.01uF
0.022uF
47uF
1uF
10uF
10%
10%
20.00%
20.00%
20.00%
25V
25V
10V
50V
50V
C339
C341
C342
C347
C348
1-104-665-11
1-128-551-11
1-162-927-11
1-126-768-11
1-126-768-11
ELECT
ELECT
CERAMIC CHIP
ELECT
ELECT
100uF
22uF
100PF
2200uF
2200uF
20.00%
20.00%
5%
20.00%
20.00%
10V
25V
50V
16V
16V
C349
C350
C801
C802
C803
1-126-934-11
1-163-037-11
1-126-960-11
1-162-970-11
1-126-934-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
220uF
0.022uF
1uF
0.01uF
220uF
20.00%
10%
20.00%
10%
20.00%
16V
25V
50V
25V
10V
C807
C808
C810
C812
C814
1-162-919-11
1-162-919-11
1-162-919-11
1-162-919-11
1-128-551-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
22PF
22PF
22PF
22PF
22uF
5%
5%
5%
5%
20.00%
50V
50V
50V
50V
25V
C816
C817
C818
C824
C825
1-126-934-11
1-162-970-11
1-107-826-11
1-162-927-11
1-162-927-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220uF
0.01uF
0.1uF
100PF
100PF
20.00%
10%
10.00%
5%
5%
10V
25V
16V
50V
50V
C826
C827
C828
C829
C830
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
100PF
100PF
100PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C831
C832
C833
C834
C835
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
100PF
100PF
100PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C838
C839
1-126-959-11 ELECT
1-126-959-11 ELECT
0.47uF
0.47uF
20.00% 50V
20.00% 50V
< CONNECTOR >
* CNP302 1-785-658-11 PIN, CONNECTOR (PC BOARD) 6P
* CNP801 1-784-787-11 CONNECTOR, FFC 26P
* CNP802 1-784-736-11 CONNECTOR, FFC 14P
CNP804 1-784-765-11 CONNECTOR, FFC 4P
CNP805 1-784-733-11 CONNECTOR, FFC 11P
< DIODE >
D320
D323
D324
D806
D807
8-719-991-33
8-719-991-33
8-719-991-33
8-719-991-33
8-719-991-33
DIODE
DIODE
DIODE
DIODE
DIODE
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
D808
D951
D952
D953
D955
8-719-109-89
8-719-991-33
8-719-991-33
8-719-991-33
8-719-109-97
DIODE
DIODE
DIODE
DIODE
DIODE
MTZJ-T-77-5.6B
1SS133T-77(CND,AUS,AR,SP)
1SS133T-77(CND,AUS,AR,SP)
1SS133T-77(CND,AUS,AR,SP)
MTZJ-T-77-6.8B
D956
D957
8-719-109-72 DIODE MTZJ-T-77-3.9B
8-719-991-33 DIODE 1SS133T-77(CND,AUS,AR,SP)
< IC >
IC321
IC801
IC802
IC803
IC805
6-701-824-11
6-801-780-01
8-759-658-46
8-759-487-03
8-759-645-87
IC
IC
IC
IC
IC
BD3870FS-E2
uPD789478GC-A03-8BT
S-81233SGY-Z
BR24C01AF-WE2
PST9128-T
< JUMPER RESISTOR >
JC136
JC236
JC307
JC801
JC803
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
JC804
JC953
1-216-864-11 METAL CHIP
1-216-864-11 METAL CHIP
0
0
5%
5%
1/16W
1/16W
< CABLE HOLDER >
*
*
*
*
*
KH301
KH303
KH304
KH305
KH306
* KH307
1-565-386-11
1-565-385-11
1-565-384-11
1-565-384-11
1-565-385-11
HOLDER, CABLE 5P
HOLDER, CABLE 4P
HOLDER, CABLE 3P
HOLDER, CABLE 3P
HOLDER, CABLE 4P
1-565-386-11 HOLDER, CABLE 5P
< COIL >
L802
1-410-521-11 INDUCTOR
100uH
47
CFD-G35
Ver 1.3 2002. 09
MAIN
Ref. No.
Part No.
Description
Remarks
< TRANSISTOR >
Q321
Q322
Q810
Q951
Q952
8-729-281-53
8-729-281-53
8-729-029-26
8-729-036-61
8-729-195-23
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC1815GR-TPE2
2SC1815GR-TPE2
DTA114YSA-TP
KRC105M-AT(CND,AUS,AR,SP)
2SA952TP-K1K2
Q953
Q954
Q955
Q956
8-729-029-92
8-729-281-53
8-729-029-26
8-729-011-92
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC143ESA-TP
2SC1815GR-TPE2
DTA114YSA-TP
2SC2001TP-K1K2
< RESISTOR >
R123
R125
R126
R127
R134
1-216-829-11
1-216-829-11
1-216-821-11
1-216-833-11
1-216-853-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
4.7K
1K
10K
470K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R223
R225
R226
R227
R234
1-216-829-11
1-216-829-11
1-216-821-11
1-216-833-11
1-216-853-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
4.7K
1K
10K
470K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R325
R326
R328
R331
R332
1-216-821-11
1-216-825-11
1-216-821-11
1-216-825-11
1-216-853-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
2.2K
1K
2.2K
470K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R333
R335
R336
R337
R338
1-216-833-11
1-216-837-11
1-216-833-11
1-216-837-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
22K
10K
22K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R339
R340
R341
R343
R348
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R801
R802
R803
1-216-864-11 METAL CHIP
1-216-829-11 METAL CHIP
1-216-864-11 METAL CHIP
0
4.7K
0
R803
1-216-817-11 METAL CHIP
470
R803
1-216-829-11 METAL CHIP
4.7K
5%
1/16W
5%
1/16W
5%
1/16W
(US,CND,E92,MX)
5%
1/16W
(SP)
5%
1/16W
(AR)
R803
1-216-833-11 METAL CHIP
10K
5%
R804
1-216-864-11 METAL CHIP
0
5%
R804
1-216-813-11 METAL CHIP
220
5%
R805
R806
1-216-864-11 METAL CHIP
1-216-864-11 METAL CHIP
0
0
5%
5%
R807
R808
R809
R810
R812
1-216-864-11
1-216-864-11
1-216-821-11
1-216-864-11
1-216-864-11
0
0
1K
0
0
5%
5%
5%
5%
5%
48
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1/16W
(AUS)
1/16W
(EXCEPT SP)
1/16W
(SP)
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
Ref. No.
Part No.
Description
R813
R814
R815
R816
R817
1-216-821-11
1-216-821-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
100
100
100
5%
5%
5%
5%
5%
Remarks
1/16W
1/16W
1/16W
1/16W
1/16W
R818
R819
R820
R821
R822
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R823
R824
R825
R826
R827
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R828
R829
R830
R831
R832
1-216-841-11
1-216-821-11
1-216-813-11
1-216-864-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
1K
220
0
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R833
R835
R836
R837
R839
1-216-864-11
1-216-864-11
1-216-841-11
1-216-841-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
47K
47K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R840
R859
R860
R864
R865
1-216-841-11
1-216-864-11
1-216-841-11
1-216-817-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
0
47K
470
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R866
R867
R868
R869
R870
1-216-821-11
1-216-864-11
1-216-821-11
1-216-837-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
0
1K
22K
0
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R871
R873
R874
R875
R876
1-216-829-11
1-216-853-11
1-216-821-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
470K
1K
4.7K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R879
R881
R882
R883
R885
1-216-813-11
1-216-821-11
1-216-833-11
1-216-833-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
1K
10K
10K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R886
R887
R889
R896
R898
1-216-821-11
1-216-821-11
1-216-829-11
1-216-829-11
1-216-853-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
4.7K
4.7K
470K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R899
R951
R952
R954
R955
1-216-841-11
1-216-845-11
1-249-421-11
1-249-413-11
1-216-809-11
METAL CHIP
METAL CHIP
CARBON
CARBON
METAL CHIP
47K
100K
2.2K
470
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/4W F
1/4W F
1/16W
R956
R958
R960
1-249-413-11 CARBON
1-216-821-11 METAL CHIP
1-216-809-11 METAL CHIP
470
1K
100
5%
5%
5%
1/4W F
1/16W
1/16W
CFD-G35
Ver 1.3 2002. 09
MAIN
Ref. No.
Part No.
Description
Remarks
R961
1-216-821-11 METAL CHIP
1K
R964
R965
1-216-809-11 METAL CHIP
1-216-817-11 METAL CHIP
100
470
Ref. No.
X801
1-781-775-21 VIBRATOR, CERAMIC 4.19MHz
X802
1-579-616-31 VIBRATOR, CRYSTAL 32.76kHz
**************************************************************
A-3178-396-A PDW BOARD, COMPLETE(US,CND,E92,MX)
*********************
A-3178-479-A PDW BOARD,COMPLETE(AUS,AR,SP)
*********************
3-238-233-01 CHASSIS (HS.R)
3-703-150-11 CLAMP
4-960-167-01 SCREW (3X8) (DIA. 10), +WH
7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
*
POWER
Description
TC
Remarks
< RESISTOR >
5%
1/16W
(CND,AUS,AR,SP)
5%
1/16W
5%
1/16W
< VIBRATOR >
*
Part No.
PDW
R351
R353
R356
R357
R359
1-216-829-11
1-216-829-11
1-216-821-11
1-216-817-11
1-216-797-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
4.7K
1K
470
10
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R360
R361
R362
R363
R364
1-216-797-11
1-216-825-11
1-216-825-11
1-216-825-11
1-216-857-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10
2.2K
2.2K
2.2K
1M
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R365
1-216-857-11 METAL CHIP
1M
5%
1/16W
R366
1-216-833-11 METAL CHIP
10K
5%
1/16W
**************************************************************
1-684-451-11 POWER BOARD
*************
*
< CAPACITOR >
< CAPACITOR >
C351
C352
C353
C354
C355
1-104-665-11
1-107-826-11
1-104-665-11
1-104-665-11
1-104-665-11
C356
C357
ELECT
CERAMIC CHIP
ELECT
ELECT
ELECT
100uF
0.1uF
100uF
100uF
100uF
20.00%
10.00%
20.00%
20.00%
20.00%
10V
16V
10V
10V
10V
1-104-665-11 ELECT
1-136-165-00 FILM
100uF
0.1uF
C358
1-136-165-00 FILM
0.1uF
C359
C360
1-128-551-11 ELECT
1-126-963-11 ELECT
22uF
4.7uF
20.00% 10V
5.00% 50V
(US,CND,E92,MX)
5.00% 50V
(US,CND,E92,MX)
20.00% 25V
20.00% 50V
C361
C362
1-162-970-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
0.01uF
0.1uF
C363
1-107-826-11 CERAMIC CHIP
0.1uF
C364
1-136-165-00 FILM
0.1uF
C365
1-136-165-00 FILM
0.1uF
C366
1-162-927-11 CERAMIC CHIP
100PF
10%
25V
10.00% 16V
(AUS,AR,SP)
10.00% 16V
(AUS,AR,SP)
5.00% 50V
(AUS,AR,SP)
5.00% 50V
(AUS,AR,SP)
5%
C901
1-163-037-11 CERAMIC CHIP
0.022uF
C901
1-115-339-11 CERAMIC CHIP
0.1uF
C902
1-163-037-11 CERAMIC CHIP
0.022uF
C902
1-115-339-11 CERAMIC CHIP
0.1uF
C903
1-163-037-11 CERAMIC CHIP
0.022uF
C903
1-115-339-11 CERAMIC CHIP
0.1uF
C904
1-163-037-11 CERAMIC CHIP
0.022uF
C904
1-115-339-11 CERAMIC CHIP
0.1uF
10%
25V
(US,CND,E92,MX)
10.00% 50V
(AUS,AR,SP)
10%
25V
(US,CND,E92,MX)
10.00% 50V
(AUS,AR,SP)
10%
25V
(US,CND,E92,MX)
10.00% 50V
(AUS,AR,SP)
10%
25V
(US,CND,E92,MX)
10.00% 50V
(AUS,AR,SP)
< JACK >
0 CNJ901 1-540-009-11 INLET, AC(US)
0 CNJ901 1-526-818-11 INLET, AC(E92,MX)
0 CNJ901 1-526-838-11 INLET, AC 2P(AUS,AR,SP)
50V
< CONNECTOR >
< CONNECTOR >
* CNP351 1-785-656-21 PIN, CONNECTOR (PC BOARD) 4P
* CNP352 1-785-656-11 PIN, CONNECTOR (PC BOARD) 4P
* CNP902 1-785-656-11 PIN, CONNECTOR (PC BOARD) 4P
* CNP903 1-785-657-11 PIN, CONNECTOR (PC BOARD) 5P
< DIODE >
< DIODE >
D351
D352
8-719-991-33 DIODE 1SS133T-77
8-719-991-33 DIODE 1SS133T-77
< IC >
IC351
D901
8-719-046-07 DIODE 2A02M
D902
8-719-046-07 DIODE 2A02M
D903
8-719-046-07 DIODE 2A02M
D904
8-719-046-07 DIODE 2A02M
**************************************************************
A-3178-403-A TC BOARD, COMPLETE
*******************
8-759-426-51 IC BA5417
< CABLE HOLDER >
* KH353
3-222-726-01 CHASSIS (TC)
7-685-783-09 SCREW +PTT 2X6 (S)
1-565-386-11 HOLDER, CABLE 5P
< CAPACITOR >
< TRANSISTOR >
Q351
Q354
8-729-281-53 TRANSISTOR
8-729-011-92 TRANSISTOR
2SC1815GR-TPE2
2SC2001TP-K1K2
C101
1-162-964-11 CERAMIC CHIP
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
0.001uF
10%
50V
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
49
CFD-G35
Ver 1.3 2002. 09
TC
Ref. No.
TRANS
TUNER
Part No.
Description
C102
C103
C104
C105
1-104-665-11
1-165-176-11
1-162-966-11
1-162-923-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.047uF
0.0022uF
47PF
20.00%
10.00%
10%
5%
10V
16V
50V
50V
Remarks
C107
C201
C202
C203
C204
1-162-962-11
1-162-964-11
1-104-665-11
1-165-176-11
1-162-966-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
470PF
0.001uF
100uF
0.047uF
0.0022uF
10%
10%
20.00%
10.00%
10%
50V
50V
10V
16V
50V
C205
C207
C301
C302
C303
1-162-923-11
1-162-962-11
1-104-665-11
1-104-665-11
1-104-665-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
47PF
470PF
100uF
100uF
100uF
5%
10%
20.00%
20.00%
20.00%
50V
50V
10V
10V
10V
C304
C305
C306
C307
1-126-947-11
1-162-962-11
1-162-970-11
1-162-964-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
470PF
0.01uF
0.001uF
20.00%
10%
10%
10%
10V
50V
25V
50V
< CONNECTOR >
CN303
Ref. No.
Part No.
Description
Remarks
R302
1-216-829-11 METAL CHIP
4.7K
5%
1/16W
R303
R304
R305
R306
R307
1-216-829-11
1-216-821-11
1-216-817-11
1-218-867-11
1-216-797-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
4.7K
1K
470
6.8K
10
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/10W
1/16W
R308
R309
R314
R315
1-216-837-11
1-216-805-11
1-216-817-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
47
470
470
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
< SWITCH >
S301
1-762-565-11 SWITCH, SLIDE (REC)
< TRANSFORMER >
T301
1-416-041-11 TRANSFORMER, BIAS OSCILLATION
**************************************************************
1-684-452-11 TRANS BOARD
************
*
1-568-830-11 CONNECTOR, FFC 11P
1-533-233-31 HOLDER, FUSE
< IC >
< FUSE >
IC301
8-759-264-71 IC TA2068N
0 F902
0 F902
< JUMPER RESISTOR >
JC301
JC302
JC303
JC304
JC305
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
JC306
JC307
JC308
1-216-295-91 SHORT
1-216-864-11 METAL CHIP
1-216-295-91 SHORT
0
0
0
5%
1/16W
< TRANSFORMER >
0 T901
1-437-644-11 TRANSFORMER, POWER(US,E92,MX)
0 T901
1-437-645-11 TRANSFORMER, POWER(AUS,AR,SP)
**************************************************************
*
A-3323-779-A TUNER BOARD, COMPLETE (US,CND,E92,MX)
**********************
*
A-3323-815-A TUNER BOARD, COMPLETE (AUS,AR,SP)
**********************
< TRANSISTOR >
Q301
8-729-120-28 TRANSISTOR
2SC2412K-T-146-R
< CAPACITOR >
< RESISTOR >
R101
R102
R103
R104
R105
1-216-835-11
1-216-807-11
1-216-843-11
1-216-827-11
1-216-835-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
15K
68
68K
3.3K
15K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R106
R110
R111
R112
R201
1-216-825-11
1-216-809-11
1-216-829-11
1-216-835-11
1-216-835-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
100
4.7K
15K
15K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R202
R203
R204
R205
R206
1-216-807-11
1-216-843-11
1-216-827-11
1-216-835-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
68
68K
3.3K
15K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R210
R211
R212
R301
1-216-025-11
1-216-829-11
1-216-835-11
1-216-857-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
4.7K
15K
1M
5%
5%
5%
5%
1/10W
1/16W
1/16W
1/16W
50
1-532-465-11 FUSE,TIME LAG 3.15A/250V(AUS,AR,SP)
1-576-109-11 FUSE 5A/125V(US,E92,MX)
C1
C4
C7
C8
C9
1-162-923-11
1-162-964-11
1-162-910-11
1-162-964-11
1-162-915-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47PF
0.001uF
5PF
0.001uF
10PF
5%
10%
0.25PF
10%
0.5PF
C10
C11
C12
C13
C14
1-126-960-11
1-107-826-11
1-126-963-11
1-162-970-11
1-164-227-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
1uF
0.1uF
4.7uF
0.01uF
0.022uF
20.00% 50V
10.00% 16V
20.00% 50V
10%
25V
10%
25V
(US,CND,E92,MX)
C14
1-162-970-11 CERAMIC CHIP
0.01uF
10%
C15
1-164-227-11 CERAMIC CHIP
0.022uF
C15
1-162-970-11 CERAMIC CHIP
0.01uF
C18
C20
1-126-934-11 ELECT
1-107-826-11 CERAMIC CHIP
220uF
0.1uF
25V
(AUS,AR,SP)
10%
25V
(US,CND,E92,MX)
10%
25V
(AUS,AR,SP)
20.00% 10V
10.00% 16V
C21
1-126-960-11 ELECT
1uF
20.00% 50V
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
50V
50V
50V
50V
50V
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
CFD-G35
Ver 1.1 2002. 05
TUNER
Ref. No.
Part No.
Description
C22
C23
C24
C26
1-107-826-11
1-126-960-11
1-162-960-11
1-162-927-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1uF
1uF
220PF
100PF
10.00%
20.00%
10%
5%
16V
50V
50V
50V
Remarks
C27
C29
C30
C31
C32
1-162-927-11
1-104-665-11
1-162-970-11
1-162-919-11
1-162-964-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100uF
0.01uF
22PF
0.001uF
5%
20.00%
10%
5%
10%
50V
10V
25V
50V
50V
C33
C34
C35
C37
C39
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.1uF
10%
10%
10%
10%
10.00%
25V
25V
25V
25V
16V
C41
C42
C43
C47
C49
1-164-230-11
1-162-927-11
1-162-919-11
1-162-915-11
1-161-051-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC
220PF
100PF
22PF
10PF
0.01uF
5.00%
5%
5%
0.5PF
10%
50V
50V
50V
50V
50V
C51
C52
C53
C54
C55
1-162-919-11
1-162-915-11
1-136-169-00
1-126-934-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
FILM
ELECT
CERAMIC CHIP
22PF
10PF
0.22uF
220uF
100PF
5%
0.5PF
5.00%
20.00%
5%
50V
50V
50V
10V
50V
C56
C57
C59
C60
C61
1-162-964-11
1-162-964-11
1-162-927-11
1-162-964-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
100PF
0.001uF
100PF
10%
10%
5%
10%
5%
50V
50V
50V
50V
50V
C62
C63
C65
C66
C68
1-162-927-11
1-162-927-11
1-126-963-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
4.7uF
100PF
100PF
5%
5%
20.00%
5%
5%
50V
50V
50V
50V
50V
C77
1-162-968-11 CERAMIC CHIP
0.0047uF
10%
C78
1-162-968-11 CERAMIC CHIP
C80
C95
1-162-970-11 CERAMIC CHIP
1-162-964-11 CERAMIC CHIP
Ref. No.
Part No.
Description
Remarks
< IC >
IC1
IC2
6-700-512-01 IC TA2149BN
8-759-483-40 IC LC72137M-TLM
< JUMPER RESISTOR >
JC1
JC2
JC3
JC4
JC5
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
JC6
JC11
JC12
JC13
JC24
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
JC33
JC34
1-216-864-11 METAL CHIP
1-216-864-11 METAL CHIP
0
0
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
(AUS,AR,SP)
1/16W
1/16W
< COIL >
L1
L2
L3
L3
L4
1-409-775-11
1-416-509-11
1-428-947-11
1-754-117-11
1-411-234-21
COIL, AIR-CORE
COIL, AIR-CORE
COIL, FERRITE-ROD ANTENNA
ANTENNA, FERRITE-ROD (MW)
COIL, AM OSC
L11
L21
1-414-142-11 INDUCTOR
1-410-509-11 INDUCTOR
1uH(US,E92,MX)
10uH
< RESISTOR >
50V
(AUS,AR,SP)
0.0047uF 10%
50V
(AUS,AR,SP)
0.01uF
10%
25V
0.001uF 10%
50V
< FILTER >
CF2
CF4
1-760-233-71 FILTER, CERAMIC
1-781-962-21 FILTER, CERAMIC
R1
R2
R3
R4
R10
1-216-815-11
1-216-817-11
1-216-833-11
1-216-833-11
1-216-805-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
330
470
10K
10K
47
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R11
R13
R24
R30
R31
1-216-827-11
1-216-825-11
1-216-813-11
1-216-835-11
1-216-827-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
2.2K
220
15K
3.3K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R32
R40
R41
R50
R51
1-216-845-11
1-216-849-11
1-216-833-11
1-216-821-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
220K
10K
1K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R52
R53
R54
R56
R58
1-216-864-11
1-216-835-11
1-216-817-11
1-216-815-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
15K
470
330
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R59
R60
R61
R63
R65
1-216-825-11
1-216-825-11
1-216-825-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
2.2K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R91
R92
R94
1-216-813-11 METAL CHIP
1-216-813-11 METAL CHIP
1-216-821-11 METAL CHIP
220
220
1K
5%
5%
5%
1/16W
1/16W
1/16W
< CONNECTOR >
* CNP1
1-564-713-11 PIN, CONNECTOR (SMALL TYPE)11P
< TRIMMER >
CT1
CT3
1-141-603-11 CAP, ADJ
1-141-601-11 CAP, ADJ
< DIODE >
D1
D2
D3
D10
D11
8-719-078-48
8-719-078-48
8-719-050-69
8-719-988-61
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
KV1471ETR1-3
KV1471ETR1-3
KV1520NT
1SS355TE-17
1SS355TE-17
51
CFD-G35
Ver 1.4 2002. 11
TUNER
Ref. No.
Part No.
Description
Remarks
< TRANSFORMER >
T1
T2
1-433-741-11 TRANSFORMER, IF
1-419-465-11 COIL (DET)
< VIBRATOR >
Ref. No.
Part No.
X1
1-781-592-11 VIBRATOR, CRYSTAL 75kHz (US,CND,E92,MX)
X1
1-760-130-11 VIBRATOR, CRYSTAL 75kHz (AUS,AR,SP)
**************************************************************
1-823-740-11
1-823-744-11
1-452-899-11
1-757-778-11
1-823-742-11
CABLE, FLEXIBLE FLAT (26 CORE)
CABLE, FLEXIBLE FLAT (4 CORE)
MAGNET
CABLE, FLEXIBLE FLAT (11 CORE)
WIRE (FLAT TYPE) (14 CORE)
124
0 251
ANT1
HE301
HRP301
1-757-689-11
8-820-161-02
1-501-883-21
1-543-876-11
1-500-691-11
CABLE, FLEXIBLE FLAT (16 CORE)
OPTICAL PICK-UP KSS-213R
ANTENNA, TELESCOPIC
HEAD (ERASE)
HEAD,MAGNETIC(RECORD/PLAYBACK)
M321
M701
S321
S322
S801
A-3320-446-A
X-2162-712-1
1-771-686-11
1-762-679-11
1-692-960-11
MOTOR, ASSY (CAPSTAN/REEL)
GEAR ASSY (R) (RP), MOTOR (SLED)
SWITCH, LEAF (PLAY SW)
SWITCH, LEAF (MOTOR SW)
SWITCH, PUSH (1 KEY) (ZPUSH OPEN/CLOSE)
52
Remarks
ACCESSORIES
************
MISCELLANEOUS
***************
9
17
58
103
123
Description
SP391 1-825-029-11 SPEAKER (10cm)(BLACK)
SP391 1-825-159-11 SPEAKER (10cm)(SILVER)
SP392 1-825-029-11 SPEAKER (10cm)(BLACK)
SP392 1-825-159-11 SPEAKER (10cm)(SILVER)
SP393 1-825-030-11 SPEAKER (8cm) (WOOFER)
**************************************************************
0
0
0
0
0
A-3170-228-A REMOTE COMMANDER (RMT-CEX35AD)
(SILVER)
A-3170-229-A REMOTE COMMANDER (RMT-CG35A)
(BLACK)
1-557-287-11 CORD, POWER (E92,MX)
1-575-131-11 CORD, POWER (SP)
1-696-819-11 CORD, POWER (AUS)
1-783-878-11
1-783-952-11
3-027-153-01
3-027-153-11
3-241-303-11
CORD, POWER (US,CND)
CORD, POWER (AR)
LID, BATTERY CASE (FOR RMT-CG35A)
LID, BATTERY CASE (FOR RMT-CEX35AD)
MANUAL, INSTRUCTION (ENGLISH)
(US,CND,E92,MX)
3-241-303-21 MANUAL, INSTRUCTION (FRENCH) (CND)
3-241-303-31 MANUAL, INSTRUCTION (SPANISH) (E92,MX)
3-241-303-41 MANUAL, INSTRUCTION (ENGLISH,SPANISH)
(AUS,AR,SP)
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
CFD-G35
MEMO
53
CFD-G35
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
Date
Description of Revision
1.0
2002.03
New
1.1
2002.05
Addition of Australian, Argentina and Singapore model
1.2
2002.07
Ref.No.251, 258 and M701 changed into the parts only for services
(ENG-02014)
(SPM-02027)
1.3
2002.09
Addition of Canadian model
(ENG-02033)
1.4
2002.11
Correction of parts numbers of remote commanders
(SPM-02051)

Similar documents

cfd-g70 service manual supplement

cfd-g70 service manual supplement LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES S...

More information

Pages 51-100 Catalog Volume 16

Pages 51-100 Catalog Volume 16 Plastic 12 ”x12 ” Plastic 12 ”x12 ” $18.00 dz 12 dz Assorted $16.50 dz Min. 6 pcs per style

More information

ICF-CD873 - Electronica.ro

ICF-CD873 - Electronica.ro LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES S...

More information

CFD-G505 - Panasonic Parts and Accessories

CFD-G505 - Panasonic Parts and Accessories RMS power, with no more than 10 % total harmonic distoration in AC operation. Woofer with 4-ohm loads, driven at 50 - 150 Hz; rated 6 W minimum RMS power, with no more than 10 % total harmonic dist...

More information