SERVICE MANUAL
Transcription
SERVICE MANUAL
XES-Z50 SERVICE MANUAL US Model Canadian Model Ver 1.1 2001.09 • This set consists of the following units. Model Name Using Similar Mechanism NEW CHANGER UNIT CD Mechanism Type MG-110ES-132 CONTROL UNIT Optical Pick-up Name KSS-400A WIRELESS REMOTE COMMANDER (RM-X67) ROTARY REMOTE COMMANDER (RM-X66) SPECIFICATIONS – Continued on next page – DIGITAL REFERENCE SOUND SYSTEM 9-925-509-12 Sony Corporation 2001I0500-1 C 2001.9 e Vehicle Company Shinagawa Tec Service Manual Production Group Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270 ˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. NOTES ON HANDLING THE OPTICAL PICKUP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. Laser Diode Properites • Material: GaAlAs • Wavelength: 780 nm • Emission Duration: continuous • Laser Output Power: less than 44.6 µW* * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. –2– TABLE OF CONTENTS 1. SERVICING NOTES 1-1. Connection at Repair .................................................... 1-2. Front Panel Setting ....................................................... 1-3. Removal of Front Panel at Power Off ........................... 2. 7. 4 4 4 GENERAL Overview ...................................................................... Precautions ................................................................... Initial Settings ............................................................... Attaching/Detaching the Electrically Operated Display Section ............................................. Setting the Clock .......................................................... Inserting CDs ................................................................ Using the Rotary Remote ............................................. Using the Wireless Remote .......................................... Menu Display/Lists ...................................................... Listening to a CD .......................................................... Playing Tracks Repeatedly ........................................... Playing Tracks in Random Order ................................. Selecting Specific Tracks for Playback ........................ Setting Sound Effects for Each CD/MD ....................... Labeling a CD ............................................................... Locating a Disc by Title ............................................... Viewing CD TEXT Information ................................... Listening to Radio ........................................................ Presetting Radio Stations .............................................. Specifying Monaural/Stereo Mode ............................... Receiving Only the Strongest Signals .......................... Labeling Radio Stations ............................................... Selecting a Station by Name ......................................... Set up Menu .................................................................. AUX Menu ................................................................... Selecting the Parametric Equalizer Pattern .................. Selecting the Cross-over Network Pattern ................... Listening to an Optional CD/MD Changer .................. Precautions and Maintenance ....................................... An Example of FIR Filter (4095 tap) Frequency Response Table .......................... Installing the Wireless Remote ..................................... After Installation and Connections Have Been Completed .................................................. Installing the Rotary Remote ........................................ Installing the Control Unit ............................................ Installing the CD Changer ............................................ Connection Diagram (3Way System) ........................... System Configuration Examples .................................. 5 5 6 7 8 9 11 12 13 13 14 15 15 16 17 18 19 20 21 22 23 23 25 25 26 27 28 28 29 30 31 31 31 32 34 35 36 3. DISASSEMBLY ....................................................... 37 4. MECHANICAL ADJUSTMENT ......................... 45 5. TEST MODE ............................................................ 46 6. ELECTRICAL ADJUSTMENTS Tuner Section ................................................................ CD Section .................................................................... Display Section ............................................................. DIAGRAMS 7-1. IC Pin Function Description ......................................... 52 7-2. IC201 (BA6247FP-Y) Motor Driver IC Operation ...... 76 7-3. Block Diagram — Control Unit (TUNER Section) — .......................... 77 7-4. Block Diagram — Control Unit (DISPLAY Section) — ....................... 79 7-5. Block Diagram — Control Unit (BUS CONTROL/POWER SUPPLY Section) — ........ 81 7-6. Block Diagram — Changer Unit (CD Section (1/2)) — ....................... 83 7-7. Block Diagram — Changer Unit (CD Section (2/2)) — ....................... 85 7-8. Block Diagram — Changer Unit (MAIN Section (1/2)) — .................. 87 7-9. Block Diagram — Changer Unit (MAIN Section (2/2)) — .................. 89 7-10. Block Diagram — Changer Unit (D/A CONVERTER Section) — ...... 91 7-11. Block Diagram — Changer Unit (BUS CONTROL/POWER SUPPLY Section) — ........ 93 7-12. Printed Wiring Board — Control Unit (MAIN Section) — ............................ 98 7-13. Schematic Diagram — Control Unit (MAIN Section) — ............................ 101 7-14. Schematic Diagram — Control Unit (FRONT PANEL/ DESORPTION MECHANISM Section) — ................ 106 7-15. Printed Wiring Boards — Control Unit (FRONT PANEL/ DESORPTION MECHANISM Section) — ................ 111 7-16. Printed Wiring Boards — Changer Unit (DRIVER Section) — ....................... 116 7-17. Schematic Diagram — Changer Unit (DRIVER Section) — ....................... 119 7-18. Printed Wiring Boards — Changer Unit (CHANGER Section) — .................. 123 7-19. Schematic Diagram — Changer Unit (CHANGER Section) — .................. 127 7-20. Schematic Diagram — Changer Unit (DSP Section) — .............................. 132 7-21. Printed Wiring Board — Changer Unit (DSP Section) — .............................. 137 7-22. Printed Wiring Boards — Changer Unit (DAC Section) — .............................. 142 7-23. Schematic Diagram — Changer Unit (DAC Section) — .............................. 145 8. EXPLODED VIEWS .............................................. 170 9. ELECTRICAL PARTS LIST ............................... 183 46 48 49 –3– SECTION 1 SERVICING NOTES 1-1. CONNECTION AT REPAIR In repairing this set, connect as follows. CN501 power supply connector CONTROL UNIT ACC BATT GND CN502 bus connector bus cable CN12 MASTER BUS CONTROL connector +12V CHANGER UNIT regulated dc power supply 14.4 V dc + – 1-2. FRONT PANEL SETTING In repairing the front panel, make a setting through the procedure give below. Notes: 1. A flat cable and a switch flexible board connected between liquid crystal module and display board are easily broken, thus requiring extreme care when handling. 2. As only the removal procedure is given here, see “3. DISASSEMBLY” for details. Setting: 1. Remove the front panel from control unit. 2. Remove the front panel (ornament) assembly. At this time, take care not to break the switch flexible board connected to the display board. 3. Remove the switch flexible board from front panel (ornament) assembly. 4. Under this condition, attach the front panel to the control unit, and supply the power. 5. After completion of attachment, turn the power OFF once, and tilt the liquid crystal module toward the front as shown below. GND CN11 POWER terminal CONTROL UNIT RELEASE button liquid crystal module DISPLAY board SWITCH FLEXIBLE board 1-3. REMOVAL OF FRONT PANEL AT POWER OFF Refer to “3. DISASSEMBLY” (page 42). –4– SECTION 2 GENERAL –5– This section is extracted from instruction manual. –6– –7– –8– –9– – 10 – – 11 – – 12 – – 13 – – 14 – – 15 – – 16 – – 17 – – 18 – – 19 – – 20 – – 21 – – 22 – – 23 – – 24 – – 25 – – 26 – – 27 – – 28 – – 29 – – 30 – – 31 – – 32 – – 33 – – 34 – – 35 – – 36 – SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. CHANGER SECTION DSP ASS’Y (Page 37) COVER (UPPER • LOWER) (Page 38) FRONT/SIDE/ REAR PANEL (Page 38) MECHANISM DECK SECTION (MG-110ES-132) (Page 39) COVER (MDEK) ASS’Y, ESCUTCHEON (2) (Page 40) SW BOARD (Page 39) EV SECTION, CHASSIS (MZ,EK) ASS’Y (Page 41) ROLLER (T), DPT BOARD, ARM (KR) COMPLETE ASS’Y (Page 41) DRIVER BOARD, OPTICAL PICK-UP (KSM-400AAM) (Page 40) CONTROLLER SECTION FRONT PANEL ASS’Y (Page 42) SUB PANEL ASS’Y, FRONT PANEL DESORPTION MACHINERY (Page 43) MOTOR ASS’Y (FRONT PANEL DESORPTION) (M1) (Page 43) LIQUID CRYSTAL MODULE (Page 42) TUNER ASS’Y (Page 44) Note: Follow the disassembly procedure in the numerical order given. CHANGER SECTION [DSP ASS’Y] 3 connector (CNP902) 1 three screws (B 3 × 6) 3 connector (CNP901) 4 DSP ass’y 2 Open the seal (DSP). 1 three screws (B 3 × 6) – 37 – 4 cover (upper • lower) [COVER (UPPER • LOWER) ] 2 three screws (M 3 × 6) 2 three screws (M 3 × 6) 3 three spacers (cover) 3 three spacers (cover) 1 seal (DSP) 6 three spacers (cover) 7 cover (upper • lower) 5 three screws (M 3 × 6) 6 three spacers (cover) 5 three screws (M 3 × 6) [FRONT/SIDE/REAR PANEL] 0 two hexagon socket bolts (M 3 × 8) 8 switch flexible board (CNJ301) 4 two screws (B 3 × 6) 7 connector (CNP302) !¡ side panel 6 RF flexible board (CNJ601) 0 two hexagon socket bolts (M 3 × 8) 4 two screws (B 3 × 6) 5 driver flexible board (CNJ501) 9 rear panel, changer board 1 two hexagon socket bolts (M 3 × 10) 0 two hexagon socket bolts (M 3 × 8) !¡ side panel 1 two hexagon socket bolts (M 3 × 10) 2 front panel ass’y – 38 – 3 connector (CNP11) 0 two hexagon socket bolts (M 3 × 8) [MECHANISM DECK SECTION (MG-110ES-132) ] 2 chassis (TOP) 1 two screws (BVTT 2.6 × 4) 3 two screws (P 2.6 × 4) 1 three screws (BVTT 2.6 × 4) 4 cover (damper L) 6 tension spring (FL2) 3 three screws (P 2.6 × 4) 5 two dampers (CNG) 4 cover (damper R) 3 two screws (P 2.6 × 4) 6 tension spring (FL2) 7 mechanism deck section (MG-110ES-132) 5 two dampers (CNG) 3 three screws (P 2.6 × 4) [SW BOARD] 5 four screws (PTT 2 × 5) 8 SW board 6 screw (PTT 2.6 × 6) 3 screw (BVTT 2 × 5) 7 connector (CNP801) 4 bracket (FPC) 2 bracket (TR2) 1 screw (PTT 2 × 4) – 39 – [COVER (MDEK) ASS’Y, ESCUTCHEON (2)] 1 two screws (PTT 2 × 4) 1 four screws (PTT 2 × 4) 4 cover (MDEK) ass’y 1 two screws (PTT 2 × 4) 2 tension spring (EV) 3 two claws 6 escutcheon (2) 5 claw [DRIVER BOARD, OPTICAL PICK-UP (KSM-400AAM) ] 4 three screws (BVTT 2 × 5) 8 four screws (P 2 × 4) 4 screw (BVTT 2 × 5) 5 DRIVER board, optical pick-up (KSM-400AAM) 9 DRIVER board 0 insulating sheet (EV) 3 driver flexible board (CNJ102) 2 RF flexible board !¡ bracket (OP) !™ spacer (W) 6 flexible board (CNJ101) !£ optical pick-up (KSM-400AAM) 7 flexible board (CNJ202) !™ two spacers (W) 1 flexible board (CNJ204) – 40 – [EV SECTION, CHASSIS (MZ, EK) ASS’Y] 4 rack (110) 3 screw (PTT 2 × 4) 6 four screws (PTT 2 × 4) 5 EV section 1 two washers 2 lever (X) ass’y 7 chassis (MZ, EK) ass’y 1 two washers 2 lever (X) ass’y 2 lever (X) ass’y 1 two washers [ROLLER (T), DPT BOARD, ARM (KR) COMPLETE ASS’Y] !¡ arm (KR) complete ass’y !™ compression spring 2 roller gear (K) ass’y !™ compression spring 6 connector (CNP701) 3 bearing (roller) 4 roller (T) !£ two washers 7 screw (BVTT 2 × 5) !¢ slide lever 8 DPT board !∞ roller (SL) 0 bracket (DPTT) 9 two screws (PTT 2 × 4) 5 two washers 3 bearing (roller) 1 stop ring (2.0) – 41 – CONTROLLER SECTION [FRONT PANEL ASS’Y] 1 screw (PTT 2.6 × 6) 2 case (lock upper) 3 Turn the gear (A) to direction of the arrow A. 1 three screws (PTT 2.6 × 6) A 4 front panel ass’y [LIQUID CRYSTAL MODULE] 1 two screws (P 2 × 6.0) 5 flexible board (CN902) 2 panel (rear) ass’y 7 front panel (ornament) ass’y 1 two screws (P 2 × 6.0) 6 liquid crystal modure 3 three screws (1.4 × 3) 4 switch flexible board – 42 – [SUB PANEL ASS’Y, FRONT PANEL DESORPTION MACHINERY] 6 front panel desorption machinery 1 two screws (P 2.6 × 6) 5 sub panel ass’y tuner control section 2 two screws (PTT 2.6 × 10) 1 two screws (P 2.6 × 6) 3 connector (CN53) 4 two connectors (CN52, 54) 2 two screws (PTT 2.6 × 10) [MOTOR ASS’Y (FRONT PANEL DESORPTION) (M1) ] 1 flexible 1 board (CN15) 7 two screws (P 2 × 3.0) 4 three screws (P 2 × 2.0) 2 two screws (B 2 × 4) 5 bracket (motor), open/close 2 board 6 connector (CN13) 3 flexible 2 board (CN14) 8 motor ass’y (from panel desorption) (M1) – 43 – [TUNER ASS’Y] 2 chassis (main upper) 1 two screws (PTT 2.6 × 6) 4 two connectors (CN505, 509) 3 screw (PTT 2.6 × 6) 8 two connectors (CN506, 507) 5 two screws (B 2.6 × 10) 1 four screws (PTT 2.6 × 6) 6 two spacers 7 tuner ass’y 5 two screws (B 2.6 × 10) 6 two spacers – 44 – SECTION 4 MECHANICAL ADJUSTMENT 4-1. ELEVATOR HEIGHT ADJUSTMENT This adjustment should be done when replacing the rack assembly on the parts related to it. Procedure: 1. Fit the EV gear assembly after adjusting its slit position as shown in the figure. (When the slit position is out of order after fitting, it can be adjusted finely turning the worm gear of the ELV motor.) slit 2. Fit the rack assembly putting it in the arrow A direction. At this time insert a spacer (approx. 1 mm thickness) or fit the rack assembly while pushing the EV chassis assembly in the arrow B direction. screw PTT 2 × 4 rack (110) ass’y EV chassis ass’y two screws PTT 2 × 4 A EV gear ass’y (slit position) B Note: When this adjustment is out of order, it doesn’t operate normally and the roaring of the motor can be heard. In this case adjust again. ELV motor – 45 – SECTION 5 TEST MODE This set have the test mode function. In the test mode, FM Auto Scan/Stop Level and AM Auto Scan/Stop Level adjustments can be performed easier than it in ordinary procedure. FM AUTO SCAN/STOP LEVEL ADJUSTMENT Setting: TUN/AUX button: FM FM RF signal generator Setting the Test Mode 1. Press the OFF button on the control unit to turn off the set. 2. Press the following buttons on the wireless remote commander in the given order. → Releasing the Test Mode 1. Press the OFF button on the control unit. Note: All operations except OFF button are done with the wireless remote commander. SECTION 6 ELECTRICAL ADJUSTMENTS TUNER SECTION 0.01 µF set → LIST 3. Press the BACK button on the wireless remote commander until a beep sounds (for more than 2 seconds). 4. At the same time as a beep, “Test” is displayed at the upper left of display, and the test mode is activated. antenna (MAIN) terminal Carrier frequency Output level Mode Modulation : 97.9 MHz : 22 dB (12.6 µV) : mono : 1 kHz, 22.5 kHz deviation (30%) Adjustment Procedure: 1. Set to the test mode. 2. Press the TUN/AUX button on the wireless remote commander to select FM. DISPLAY 3. Press the LIST button on the wireless remote commander to display “PRESET NAME LIST”. 4. Using cursor buttons on the wireless remote commander, select preset No.3, and press the ENTER button. 0dB=1µV Cautions during repair When the tuner unit is defective, replace it by a new one because its internal block is difficult to repair. DISPLAY Note: Adjust the tuner section in the sequence shown below. 1. FM Auto Scan/Stop Level Adjustment 2. FM Stereo Separation Adjustment 3. FM Noise Focus Adjustment 4. AM Auto Scan/Stop Level Adjustment • In making adjustment, connect the control unit and changer unit. 5. Adjust with the volume RV203 on FM/AM tuner unit so that the “FM” indication turns to “FM0” indication on the display window. But, in case of already indicated “FM0”, turn the RV203 so that put out light “0” indication and adjustment. DISPLAY Adjustment Location: Control Unit (FM/AM tuner unit) (See page 50) – 46 – AM AUTO SCAN/STOP LEVEL ADJUSTMENT FM STEREO SEPARATION ADJUSTMENT Setting: TUN/AUX button : FM FM RF signal generator level meter antenna (MAIN) terminal 0.01 µF 10 k Ω + – set Carrier frequency Output level Mode Modulation Note: Make this adjustment after “FM AUTO SCAN/STOP LEVEL ADJUSTMENT”. Setting: TUN/AUX button: AM 30 Ω 15 pF 65 pF : 97.9 MHz LINE OUT (FRONT) jack : 70 dB (3.2 mV) : stereo : main: 1 kHz, 33.75 kHz deviation (45%) sub: 1 kHz, 33.75 kHz deviation (45%) 19 kHz pilot: 7.5 kHz deviation (10%) AM RF signal generator AM dummy antenna (50 Ω) Adjustment Procedure: FM Stereo Level meter signal generator connection output channel antenna (MAIN) terminal Carrier frequency : 1000 kHz 30% amplitude modulation by 1 kHz signal Output level : 33 dB (44.7 µV) Level meter reading (dB) L-CH A R-CH L-CH B Adjust RV204 on FM/AM tuner unit for minimum reading. R-CH R-CH C R-CH D Adjust RV204 on FM/AM tuner unit for minimum reading. L-CH L-CH set L-CH Stereo separation: A-B R-CH Stereo separation: C-D The separations of both channels should be equal. Adjustment Procedure: 1. Set to the test mode. (See page 46.) 2. Press the TUN/AUX button on the wireless remote commander to select AM. DISPLAY 3. Press the LIST button on the wireless remote commander to display “PRESET NAME LIST”. 4. Using cursor buttons on the wireless remote commander, select preset No.3, and press the ENTER button. Specification: Separation more than 28 dB Adjustment Location: Control Unit (FM/AM tuner unit) (See page 50) DISPLAY FM NOISE FOCUS ADJUSTMENT Setting: TUN/AUX button: FM FM RF signal generator level meter antenna (MAIN) terminal 0.01 µF set Carrier frequency Output level Mode Modulation 5. Adjust with the volume RV201 on FM/AM tuner unit so that the “AM” indication turns to “AM0” indication on the display window. But, in case of already indicated “AM0”, turn the RV201 so that put out light “0” indication and adjustment. 10 k Ω + – : 97.9 MHz : 60 dB (1 mV) LINE OUT (FRONT) jack : stereo : 1 kHz, 75 kHz deviation DISPLAY Adjustment Procedure: 1. Tune the set to 97.9 MHz. 2. The then output level is supposing than (A) dB. 3. Adjust with the volume RV205 on FM/AM tuner unit so that the output level is (A) –32 dB then signal generator input set to –20 dB. Adjustment Location: Control Unit (FM/AM tuner unit) (See page 50) Adjustment Location: Control Unit (FM/AM tuner unit) (See page 50) – 47 – TRACKING OFFSET ADJUSTMENT CD SECTION Notes: 1. Perform adjustments in the order given. 2. Use YEDS-18 disc (Part No.: 3-702-101-01) unless otherwise indicated. 3. Use the oscilloscope with more than 10 MΩ impedance. 4. Power supply voltage requirement: DC 14.4 V (more than 3 A) 5. In making adjustment, connect the control unit and changer unit. FOCUS BIAS ADJUSTMENT Condition: This adjustment is performed with the set placed horizontally. Connection: oscilloscope (AC range) DRIVER board TP (RF) TP (VC) Condition: This adjustment is performed with the set place horizontally. Connection: oscilloscope (DC range) DRIVER board TP (TE) TP (VC) + – Adjustment Procedure: 1. Connect the oscilloscope to TP (TE) and TP (VC) on the DRIVER board. 2. Put the set into play mode by loading the disc (YEDS-18). 3. Press the cursor buttons on the wireless remote commander, observe the traverse waveform *. 4. Adjust the RV101 on the DRIVER board so that the oscilloscope reading is symmetrical in relation to 0 ± 0.05 V. * Traverse waveform: This is the tracking error waveform appears when crossing the track. + – VOLT/DIV : 1 V (with the 10: 1 probe in use) TIME/DIV : 2 msec CENTER : 0 ± 0.05 V Adjustment Procedure: 1. Connect the oscilloscope to TP (RF) and TP (VC) on the DRIVER board. 2. Put the set into play mode by loading the disc (YEDS-18). 3. Adjust the RV102 on the DRIVER board so that the waveform on the oscilloscope (eye pattern) is good. A good eye pattern means that the diamond shape (≈) in the center of the oscilloscope can be clearly distinguished. A C 0± 0.05 V B C=1.8 ± 0.3 V • RF signal reference waveform (eye pattern) traverse waveform (100 track jump waveform) VOLT/DIV : 200 mV (with the 10: 1 probe in use) TIME/DIV : 0.5 µsec Connection and Adjustment Location: DRIVER board (See page 50) 1.1 +0.3 –0.2 Vp-p Note: When observing the eye pattern, set the oscilloscope to AC range and raise the vertical sensitivity so that it may be easily seen. Connection and Adjustment Location: DRIVER board (See page 50) – 48 – DISPLAY SECTION CONTRAST ADJUSTMENT Note on adjustment: Adjust the contrast at “8” of 15 steps. Connection: digital voltmeter liquid crystal module TP1 TP2 + – Adjustment Procedure: 1. Fix display board and rear panel with screws. 2. Connect the display board and liquid crystal module. 3. Connect the front panel of which status is as shown above to the control unit. (Display will turn on.) 4. After the display turned on, allow ten minutes to elapse, then connect a digital voltmeter to TP1 and TP2 of liquid crystal module. 5. Adjust RV801 on the display board so that the reading of digital voltmeter satisfies the specified value. Specified Value: 20.95 V to 21.00 V Adjustment Location: DISPLAY board (See page 51) – 49 – CONNECTION AND ADJUSTMENT LOCATION • TUNER Section – Control Unit (FM/AM Tuner Unit) – AM AUTO SCAN/STOP LEVEL Adjustment RV201 FM STEREO SEPARATION Adjustment RV204 FM AUTO SCAN/STOP LEVEL Adjustment RV203 front side FM NOISE FOCUS Adjustment RV205 • CD Section – DRIVER Board (Conductor Side) – CNJ102 TRACKING OFFSET Adjustment RV101 TP (RF) TP (TE) FOCUS BIAS Adjustment RV102 IC101 TP (VC) – 50 – • DISPLAY Section – Liquid Crystal Module – TP2 TP1 – DISPLAY Board (Conductor Side) – CN502 CONTRAST Adjustment RV801 – 51 – SECTION 7 DIAGRAMS 7-1. IC PIN FUNCTION DESCRIPTION MAIN BOARD IC501 mPD78P058GC-933-3B9 (SYSTEM CONTROLLER) Pin No. Pin Name I/O 1 ENC Ð I Function Rotary encoder input from the rotary commander 2 NCO O Not used (open) 3 NCO O Not used (open) 4 AVSS Ñ Ground terminal (for A/D conversion) 5 NCO O Not used (open) 6 NCO O Not used (open) 7 AVREF1 I Reference voltage input terminal (+5V) (for D/A conversion) 8 NCO O 9 NCO O 10 NCO O 11 NCO O 12 EEP SCK O Serial data transfer clock signal output to the EEPROM (IC515) 13 EEP SDA I/O Two-way data bus with the EEPROM (IC515) 14 BUSY-MA O Not used (open) 15 BUSY-TU O Not used (open) 16 UNISI I Serial data input from the bus interface (IC503) (for SONY bus) 17 UNISO O Serial data output to the bus interface (IC503) (for SONY bus) 18 UNICKI I Serial data transfer clock signal input for the bus interface (for SONY bus) 19 UNICKO O Serial data transfer clock signal output to the tuner controller (IC502), bus interface (IC503) (for SONY bus), and FM character multiple broadcast display controller (IC802) 20 BUS ON O Bus on/off control signal output to the tuner controller (IC502), bus interface (IC503) (for SONY bus), and FM character multiple broadcast display controller (IC802) ÒLÓ: bus on 21 SYS RST O Reset signal output to the tuner controller (IC502), bus interface (IC503) (for SONY bus), and FM character multiple broadcast display controller (IC802) ÒLÓ: reset 22 KEY ACT O Key active control signal output terminal (for A/D conversion power control) When KEY ACK (pin ^∞) is active, ÒLÓ is output to enable signal input 23 TX-SEL O Not used (open) 24 NCO O 25 NCO O 26 NCO O 27 CAUTION I Input terminal to set whether a caution alarm (buzzer sounds if the front panel is not removed when accessory power is in off status) sounds or not ÒHÓ: not sound, ÒLÓ: sounds (fixed at ÒLÓ) 28 TIMPOL I Input terminal to set whether time polling is provided or not ÒHÓ: provided, ÒLÓ: none (fixed at ÒLÓ) 29 TEL MUT I Telephone mute signal input terminal At input of ÒLÓ, the signal is attenuated by Ð20 dB 30 VOL STP I Not used (fixed at ÒLÓ) Not used (open) Not used (open) 31 NCO O Not used (open) 32 MUTE O Mute control signal output of the tuner audio signal ÒHÓ: mute on 33 VSS Ñ Ground terminal 34 NCO O 35 NCO O 36 NCO O 37 NCO O 38 NCO O 39 NCO O Not used (open) – 52 – Pin No. Pin Name I/O Function 40 NCO O 41 NCO O 42 NCO O 43 NCO O 44 NCO O 45 KEY ILL O Output of power on/off control signal for the rotary commander illumination power supply “H”: power on 46 XTEST I Detection input of the personal computer connection “H”: When display panel is attached at front panel position “L”: When personal computer communication accessory is attached 47 COLOR O Selection output of the illumination color 48 ANT REM O Antenna remote control signal output terminal At the reception with tuner, “H” is output when power antenna starts 49 TUNER ON O Output of power on/off control signal for the tuner power supply 50 MECHA ON O Power on/off control signal output of the front panel attach/remove mechanism circuit “H” is output during front panel attachment or removal operation 51 INDASH I Input of main unit install position detection “L”: Installed in dash board, “H”: Installed under seat, etc. 52 TESEMOD I Input terminal for setting test mode This terminal is read at the reset, and if “L”, the test mode is forcibly activated 53 FG I Input of front panel attach/remove operation detection During attach/remove operation, pulses of constant interval are input, or in stop status, “L” or “H” is always input Not used (open) Not used (open) “H”: tuner on 54 PNL SW4 I Detection input of the front panel attach/remove detect switches (S1 and S2) There are two detection switches, and if both are off, “H” is input Or, if either one is on, “L” is input “L”: When front panel is attached, “H”: When front panel attachment or removal is completed 55 PNL SW3 I Detection input of the front panel position detect switch (S23) “L”: When front panel is completely pulled in (completion of attachment) 56 PNL SW2 I Detection input of the front panel position detect switch (S22) “L”: When front panel is half pulled in 57 PNL SW1 I Detection input of the front panel position detect switch (S21) “H”: When front panel is at the position where it can be attached or removed 58 PNL M– O Output of control for front panel attach/remove mechanism drive motor (M1) *1 59 PNL M+ O Output of control for front panel attach/remove mechanism drive motor (M1) *1 60 RESET I System reset signal input from the reset signal generator (IC504) and reset switch (S51) (or (S42) when using connector box and display holder) “ L ” : reset For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H” Also, when the reset switch (S51) is pressed, “L” is input 61 SIRCS I Sircs signal input from the remote control receiver in display unit 62 BU IN I Backup power supply detect signal input from the bus interface (IC503) (for SONY bus) 63 ACC IN I Accessory power supply detect signal input terminal I Signal input from the front panel attach/remove detect switches (S1 and S2) when the front panel is attached to the control unit There are two detection switches, and if both are off, “H” is input Or, if either one is on, “L” is input “L”: When front panel is attached, “H”: When front panel attachment or removal is completed Signal is input from the nose detection switch (S41) when connector box and display holder are used “L” is input when the front panel is attached 64 NOSE SW – 53 – “L”: accessory on Pin No. Pin Name I/O Function 65 KEY ACK I Input of acknowledge signal for key input Input of acknowledge signal to accept FUNCTION and EJECT keys when the power is in off status ON at “L” input 66 AUX ON I Input of auxiliary input (AUX IN) on/off detection Input terminal to turn on the set simultaneously when an external unit connected to the AUX IN terminal is turned on, if the power of the set is off “L”: When external unit is turned on 67 NCO O Not used (open) 68 VDD — Power supply terminal (+5V) 69 X2 O Main system clock output terminal (5 MHz) 70 X1 I Main system clock input terminal (5 MHz) 71 IC — Ground terminal 72 XT2 O Sub system clock output terminal (32.768 kHz) 73 XT1 I Sub system clock input terminal (32.768 kHz) 74 AVDD — 75 AVREF0 I Reference voltage input terminal (+5V) (for A/D conversion) 76 KEY IN0 I Key (OFF key) input from the front panel section (A/D input) 77 KEY IN1 I Key (RELEASE key) input from the front panel section (A/D input) 78 RC IN0 I Key input from the rotary commander (A/D input) 79 RC IN1 I Key input from the rotary commander (A/D input) 80 ENC + I Rotary encoder input from the rotary commander Power supply terminal (+5V) (for A/D conversion) *1 Motor control Operation Stop When the front panel is being removed When the front panel is being attached Brake PNL M– (pin %•) “L” “L” “H” “H” PNL M+ (pin %ª) “L” “H” “L” “H” Terminal – 54 – MAIN BOARD IC502 MN18P83220S4K (TUNER CONTROLLER) Pin No. Pin Name I/O 1 A5 O 2 A4 O 3 A3 O 4 A2 O 5 A1 O Function Address signal output to the external RAM device Not used (open) 6 A0 O 7 VDD — 8 X1 I Main system clock input terminal (8 MHz) 9 X2 O Main system clock output terminal (8 MHz) Ground terminal Power supply terminal (+5V) 10 GND — 11 XTI I Sub system clock input terminal Not used (open) 12 XTO O Sub system clock output terminal Not used (open) 13 EX1 I Input terminal for setting microcomputer operation mode (fixed at “L”) 14 RESET I System reset signal input from the system controller (IC501) and reset signal generator (IC504) “L”: reset For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H” 15 RDS CLK I Serial data transfer clock signal input from the external device Not used (fixed at “L”) 16 BU IN I Backup power supply detection signal input from the bus interface (IC503) (for SONY bus) 17 BUSON I Bus on/off detection interrupt signal input from the system controller (IC501) “L”: bus on 18 D7 I/O 19 D6 I/O 20 D5 I/O 21 D4 I/O 22 D3 I/O 23 D2 I/O 24 D1 I/O 25 D0 I/O 26 EEP SCK O Serial data transfer clock signal output to the EEPROM (IC516) 27 NCO O Not used (open) 28 BUSY-MA O Not used (open) 29 BUSY-TU O Not used (open) 30 EEP SDA I/O Two-way data bus with the EEPROM (IC516) 31 FM AMS IN I Not used (fixed at “L”) 32 AM ST IN I AM stereo detection signal input from the FM/AM tuner unit “L”: AM stereo 33 NCO O 34 NCO O 35 NCO O 36 NIL I Not used (fixed at “L”) 37 NIL I Not used (fixed at “L”) 38 PLL DI I PLL serial data input from the FM/AM tuner unit 39 PLL DO O PLL serial data output to the FM/AM tuner unit 40 PLL CKO O PLL serial data transfer clock signal output to the FM/AM tuner unit 41 PLL CE O PLL chip enable signal output to the FM/AM tuner unit 42 UNIREQ O Communication request signal output to the bus interface (IC503) (for SONY bus) “H”: communication request 43 LINK OFF O Bus on/off control signal output of the bus interface (for SONY bus) Not used (open) Two-way data bus with the external RAM device Not used (open) Not used (open) – 55 – Pin No. Pin Name I/O Function 44 UNICKI I Serial data transfer clock signal input from the system controller (IC501) 45 UNISI I Serial data input from the bus interface (IC503) (for SONY bus) 46 UNISO O Serial data output to the bus interface (IC503) (for SONY bus) 47 VDD — Power supply terminal (+5V) 48 AVDD — Power supply terminal (+5V) (for A/D conversion) 49 AVREF I Reference voltage input terminal (+5V) (for A/D conversion) 50 MS-1 I Input terminal for PLL IC setting in the FM/AM tuner unit (fixed at “L”) 51 MS-0 I Input terminal for PLL IC setting in the FM/AM tuner unit (fixed at “L”) 52 SRAM RST I Internal RAM reset detection signal input from the reset signal generator (IC517) Input terminal to check that internal RAM data are not destroyed due to low voltage 53 MUTE SEL I Input terminal for setting mute operation (fixed at “L”) 54 DST SEL 1 I Input terminal for setting destination (fixed at “L”) 55 DST SEL 0 I Input terminal for setting destination (fixed at “H”) 56 AM VSM I AM signal meter voltage detection signal input from the FM/AM tuner unit 57 FM VSM I FM signal meter voltage detection signal input from the FM/AM tuner unit 58 AVREF– I Reference voltage input terminal (0V) (for A/D conversion) 59 AVSS — Ground terminal (for A/D conversion) 60 VSS — Ground terminal 61 TU ON O Output of power on/off control signal for the tuner system power supply “H”: tuner on 62 LO/DX O Local/DX selection signal output terminal Not used (open) 63 SEEK O Seek signal output to the FM/AM tuner unit (used for IF count output request, AGC cut etc.) Output level “L” when change the frequency 64 AM ON O Output of power on/off control signal for the AM circuit power supply, and FM/AM selection signal output terminal “H”: AM on 65 FM ON O Output of power on/off control signal for the FM circuit power supply “H”: FM on 66 MUTE O Mute control signal output to the FM/AM tuner unit “H”: mute on 67 AF SEEK I AF seek control signal input terminal Not used (fixed at “L”) 68 SRAM I Chip select signal output to the external RAM device Not used (fixed at “L”) 69 A15 O Address signal output to the external RAM device Not used (open) 70 ST/MONO I/O Input of FM stereo detection signal from FM/AM tuner unit, and output of forced monaural control signal to FM/AM tuner unit (Commonly used for stereo display input and forced monaural output) FM stereo detection at input of “L”, forced monaural at output of “L” 71 SD I Station detector detection signal input from the FM/AM tuner unit Stop level for SEEK, BTM, etc. is determined SD is present at input of “H” 72 DIVER O Diversity antenna on/off control signal output terminal “H”: antenna on 73 MAIN/SUB O Diversity antenna main/sub select signal output to the FM/AM tuner unit “H”: main, “L”: sub 74 CE O Chip select signal output to the external RAM device Not used (open) 75 A11 O 76 A10 O 77 A9 O 78 A8 O 79 A7 O 80 A6 O Address signal output to the external RAM device Not used (open) – 56 – MAIN BOARD IC802 HD6413002F16 (DISPLAY CONTROLLER) Pin No. Pin Name I/O Function 1 VDD — 2 SIRCS I Sircs signal input from the remote control receiver in display unit 3 SIRCS I Sircs signal input from the remote control receiver in display unit 4 DSPL-RST O Reset signal output to the display controller (IC901) “L”: reset At the power supply, “L” is output to reset the display controller 5 DSPL-ON O Output of power on/off control signal for the display circuit power supply “H”: power on Besides power on/off control, the display data and reset signal transmission to the display controller (IC901) is controlled at the output of “H” 6 TX-SEL O Not used (open) 7 NCO O Not used (open) 8 CS-CTL O Not used (open) 9 DOWN LOAD I “H” is input when external flash memory data are rewritten Reset signal output to the external RAM device Power supply terminal (+5V) Normally “L” 10 NIH I 11 VSS — Ground terminal 12 LCD-TX O Transmit data output to the display controller (IC901) 13 UNISO O Serial data output to the bus interface (IC503) (for SONY bus) 14 LCD-RX I Receive data input from the display controller (IC901) 15 UNISI I Serial data input from the bus interface (IC503) (for SONY bus) 16 NCO O Not used (open) 17 UNICKI I Serial data transfer clock signal input from the system controller (IC501) 18 D0 I/O 19 D1 I/O 20 D2 I/O 21 D3 I/O 22 VSS — 23 D4 I/O 24 D5 I/O 25 D6 I/O 26 D7 I/O 27 D8 I/O 28 D9 I/O 29 D10 I/O 30 D11 I/O 31 D12 I/O 32 D13 I/O 33 D14 I/O 34 D15 I/O 35 VDD — Power supply terminal (+5V) 36 A0 O Address signal output terminal 37 A1 O 38 A2 O 39 A3 O 40 A4 O 41 A5 O 42 A6 O 43 A7 O Not used (fixed at “H”) Two-way data bus with the flash memory (IC804) and S-RAM (IC805) Ground terminal Two-way data bus with the flash memory (IC804) and S-RAM (IC805) Not used Address signal output to the flash memory (IC804) and S-RAM (IC805) – 57 – Pin No. Pin Name I/O Function 44 VSS — 45 A8 O 46 A9 O 47 A10 O 48 A11 O 49 A12 O 50 A13 O 51 A14 O 52 A15 O 53 A16 O 54 A17 O Address signal output to the flash memory (IC804) 55 A18 O Address signal output to the flash memory (IC804) 56 A19 O Address signal output terminal This set uses the OR level with chip select signal of ROM-CS (pin (¡) as a chip enable signal for the flash memory (IC804) 57 VSS — Ground terminal 58 WAIT I Wait signal input terminal (fixed at “H”) 59 BREQ O Communication request signal output terminal 60 BACK O Acknowledge output terminal Not used (open) 61 ø O System clock output terminal Not used (open) 62 STBY I Hardware standby signal input terminal (fixed at “H”) 63 SYSRES I System reset signal input from the system controller (IC501) and reset signal generator (IC504) “L”: reset For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H” 64 BU-IN I Backup power supply detection signal input from the bus interface (IC503) (for SONY bus) 65 VSS — 66 EXTAL I System clock input terminal (14.745 MHz) 67 XTAL I System clock input terminal (14.745 MHz) 68 VDD — Power supply terminal (+5V) 69 AS O Address strobe signal output terminal 70 RD O Strobe signal output for data reading to the flash memory (IC804) and S-RAM (IC805) 71 HWR O Strobe signal output for data writing to the flash memory (IC804) and upper byte data writing strobe signal output to the S-RAM (IC805) 72 LWR O Strobe signal output for data writing to the flash memory (IC804) and lower byte data writing strobe signal output to the S-RAM (IC805) 73 MD0 I Input terminal for setting microcomputer operation mode (fixed at “L”) 74 MD1 I Input terminal for setting microcomputer operation mode (fixed at “L”) 75 MD2 I Input terminal for setting microcomputer operation mode (fixed at “H”) 76 AVDD — 77 AVREF I 78 AN0 I 79 AN1 I 80 AN2 I 81 AN3 I 82 AN4 I 83 AN5 I Input terminal for the test (fixed at “L”) 84 BU-IN I Backup power supply detection signal input from the bus interface (IC503) (for SONY bus) 85 PBS I Parking brake detection signal input terminal Ground terminal Address signal output to the flash memory (IC804) and S-RAM (IC805) Not used (open) Ground terminal Not used (open) Power supply terminal (+5V) (for A/D conversion) Reference voltage input terminal (+5V) (for A/D conversion) Input terminal for the test (fixed at “L”) – 58 – Not used (fixed at “L”) Pin No. Pin Name I/O 86 AVSS — Function Ground terminal (for A/D conversion) 87 BUS ON I Bus on/off detection interrupt signal input from the system controller (IC501) 88 SRAM-CS O Chip enable signal output to the S-RAM (IC805) 89 DEC-CS O Chip enable signal output terminal 90 DEC-INT I Interrupt signal input terminal Not used 91 ROM-CS O Chip enable signal output to the flash memory (IC804) 92 VSS — Ground terminal 93 LCD-BLON O Output of power on/off control signal for the back light in display unit 94 LINK-OFF O Bus on/off control signal output to the bus interface (IC503) (for SONY bus) 95 DEC-ON O Output of power on/off control signal for the external device “H”: power on Not used (open) 96 DEC-CLR O Reset signal output terminal 97 A23 O Address signal output terminal Not used (open) 98 A22 O Address signal output terminal Not used (open) 99 X.TEST I Input of personal computer connection detection “H”: When display panel is attached at front panel position “L”: When personal computer communication accessory is attached 100 A20 O Address signal output terminal “L”: bus on Not used Demodulation data are read by detecting a falling edge “L”: reset – 59 – Not used (open) “H”: power on “L”: bus on DISPLAY BOARD IC901 HD6473048-DISP01 (DISPLAY CONTROLLER) Pin No. Pin Name I/O 1 VCC — Power supply terminal (+5V) Function 2 TIR O LED drive signal output for the TIR indicator “H”: LED on Not used 3 NCO O 4 NCO O 5 NCO O 6 NCO O 7 NCO O Not used (open) 8 LCD-START O Output of command transmission start control signal to the LCD controller for liquid crystal module The OR signal with the busy signal from LCD controller for liquid crystal module is input to the LCD-BUSY (pin 9) At the start of command transmission, the signal changes like “L”®“H”®“L” so as to be a start trigger for the LCD controller = DMA controller 9 LCD-BUSY I Input of busy signal from the LCD controller for liquid crystal module At the timing of “H”®“L”, data transmission to LCD controller for liquid crystal module starts 10 RESO O Reset signal output to the external device Not used (pull-up) 11 VSS — Ground terminal 12 TX-LCD O Transmit data output to the FM character multiple broadcast display controller (IC802) 13 NCO O Not used (open) 14 RX-LCD I Receive data input from the FM character multiple broadcast display controller (IC802) 15 NCO O 16 NCO O 17 NCO O 18 D0 I/O 19 D1 I/O 20 D2 I/O 21 D3 I/O 22 VSS — 23 D4 I/O 24 D5 I/O 25 D6 I/O 26 D7 I/O 27 D8 I/O 28 D9 I/O 29 D10 I/O 30 D11 I/O 31 D12 I/O 32 D13 I/O 33 D14 I/O 34 D15 I/O 35 VCC — Power supply terminal (+5V) 36 A0 O Address signal output terminal This set uses this as a control signal to the LCD controller for liquid crystal module 37 A1 O 38 A2 O 39 A3 O Not used (open) Two-way data bus with the flash memory (IC931) and S-RAM (IC932) Ground terminal Two-way data bus with the flash memory (IC931) and S-RAM (IC932) Two-way data bus with the flash memory (IC931), S-RAM (IC932), and LCD controller for liquid crystal module Address signal output to the flash memory (IC931) and S-RAM (IC932) – 60 – Pin No. Pin Name I/O 40 A4 O 41 A5 O 42 A6 O 43 A7 O 44 VSS — 45 A8 O 46 A9 O 47 A10 O 48 A11 O 49 A12 O 50 A13 O 51 A14 O 52 A15 O 53 A16 O 54 A17 O 55 A18 O Function Address signal output to the flash memory (IC931) and S-RAM (IC932) Ground terminal Address signal output to the flash memory (IC931) and S-RAM (IC932) 56 A19 O 57 VSS — 58 NIH I Not used (fixed at “H”) 59 NCO O Not used (open) 60 NCO O Not used (open) 61 Ø O System clock output terminal Not used (open) 62 STBY I Hardware standby signal input terminal (fixed at “H”) 63 RES I Reset signal input from the display controller (IC802) “L”: reset 64 BU-IN I Not used (fixed at “H”) 65 VSS — 66 EXTAL I System clock input terminal (14.745 MHz) 67 XTAL I System clock input terminal (14.745 MHz) 68 VCC — Power supply terminal (+5V) 69 AS O Address strobe signal output terminal Not used (open) 70 RD O Data reading strobe signal output to the flash memory (IC931) and S-RAM (IC932) 71 HWR O Also, this is used as strobe signal output for data writing to the flash memory (IC931), strobe signal output for higher byte data writing to the S-RAM (IC932), or latch signal to the LCD controller for liquid crystal module 72 LWR O Also, this is used as strobe signal output for data writing to the flash memory (IC931), strobe signal output for lower byte data writing to the S-RAM (IC932), or latch signal to the LCD controller for liquid crystal module 73 MD0 I Input terminal for setting microcomputer operation mode (fixed at “L”) 74 MD1 I Input terminal for setting microcomputer operation mode (fixed at “H”) 75 MD2 I Input terminal for setting microcomputer operation mode (fixed at “H”) 76 AVDD — 77 AVREF I 78 NIL I 79 NIL I 80 NIL I 81 NIL I Ground terminal Ground terminal Power supply terminal (+5V) (for A/D conversion) Reference voltage input terminal (+5V) (for A/D conversion) Not used (fixed at “L”) – 61 – Pin No. Pin Name I/O Function 82 NIL I 83 NIL I 84 CONTR O Contrast alignment signal output to the liquid crystal module (D/A output) 85 DIMER O Back light brightness control signal output to the liquid crystal module (D/A output) 86 AVSS — Ground terminal (for A/D conversion) 87 NCO O Not used (open) 88 SRAM-CS O Chip enable signal output to the S-RAM (IC932) 89 NIL I Not used (fixed at “L”) 90 ROM-CS O Chip enable signal output to the flash memory (IC931) 91 BOOT I Not used (fixed at “H”) 92 VSS — Ground terminal 93 NCO O Not used (open) 94 NCO O Not used (open) 95 LCD RST O Reset signal output terminal “H”: reset Not used (open) 96 NCO O Not used (open) 97 BEEP O Beep sound drive signal output terminal 98 NCO O Not used (open) 99 LCD-CS O Output of chip enable signal to the LCD controller for liquid crystal module The OR signal with HWR (pin &¡) is used as a latch signal to the LCD controller for liquid crystal module “L” is output at the LCD controller data transmission 100 A20 O Address signal output terminal Not used (open) Not used (fixed at “L”) – 62 – CHANGER BOARD IC301 CXP846P48Q-1-004 (SYSTEM CONTROLLER) Pin No. Pin Name I/O Function 1 LED O LED drive signal output for the eject indicator 2 — O Not used (open) 3 — O Not used (open) 4 EECLK O Serial data transfer clock signal output to the EEPROM (IC302) 5 SINGLE I Input terminal for setting CD single mode or CD changer mode “L”: CD single mode, “H”: CD changer mode (fixed at “H”) 6 MC O Elevator up/down motor (M501) and disc load/save motor (M502) drive signal output to the BA6247FP (IC201) *1 “L”: LED on 7 MB O Elevator up/down motor (M501) drive signal output to the BA6247FP (IC201) 8 MA O Disc load/save motor (M502) drive signal output to the BA6247FP (IC201) 9 PGR O Plunger drive signal output for the magazine out 10 M3 O Disc eject motor (M801) drive signal output to the BA6287F (IC801) 11 M3 O Disc eject motor (M801) drive signal output to the BA6287F (IC801) 12 ELVON O Output of power on/off control signal for the CD section main power supply 13 CDRST O Reset signal output to the D-RAM controller (IC401), digital signal processor (IC501), and digital servo processor (IC601) “L”: reset 14 XTLSEL O Output terminal for setting DSP crystal Not used (open) 15 APC O Laser diode on/off control signal output to the RF amplifier (IC101) 16 DPT I Detection input from the disc detect sensor (Q702) Whether a disc is present at the reset processing or load/save processing is detected (“L” is input while a disc is fed) 17 DOE I Detection input from the disc detect sensor (Q701) Whether a disc is present at the reset processing or load processing is detected (“L” is input when a disc is above the pickup) 18 CES I Detection input from the disc chucking completion detect switch (SW701) “L” is input when disc chucking is completed 19 HOME I Detection input from the home/top position detect switch (SW501) “L” is input when elevator is at the home position 20 PST I Detection input from the magazine detect switch (SW804) 21 LOT I Detection input from the liner slide lever position detect switch (SW803) 22 XWRE O Enable signal output for data writing to the D-RAM controller (IC401) 23 XRDE O Enable signal output for data reading to the D-RAM controller (IC401) 24 XQOK O Output of definite subcode Q data to the D-RAM controller (IC401) 25 GRSRST O Reset signal output to the D-RAM controller (IC401) 26 ESPXLT O Serial latch signal output to the D-RAM controller (IC401) 27 XSOE O Enable signal output for data reading to the D-RAM controller (IC401) 28 SDTI I Serial data input from the D-RAM controller (IC401) 29 — O Not used (open) 30 RESET I System reset signal input from the reset signal generator (IC903) and bus interface (IC951) (for SONY bus) “L”: reset For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H” 31 XTLI I Main system clock input terminal (8 MHz) 32 XTLO O Main system clock output terminal (8 MHz) 33 VSS — Ground terminal 34 TX O Sub system clock output terminal (32.768 kHz) 35 TEX I Sub system clock input terminal (32.768 kHz) – 63 – *1 *1 “H”: power on “H”: internal clock, “L”: external clock “L”: laser on “L”: magazine in “L”: magazine in At track jump, “H” is output Not used (open) Not used (fixed at “L”) Pin No. Pin Name I/O Function 36 AVSS — 37 AVREF I Reference voltage input terminal (+5V) (for A/D conversion) 38 TEMP H I Temperature detect thermistor (TH301) input terminal (A/D input) Used for high temperature detection data input (for servo gain compensation) 39 TEMP L I Temperature detect thermistor (TH302) input terminal (A/D input) Used for low temperature detection data input (for servo gain compensation) 40 SEL O Not used (open) 41 TEMP D I Input of temperature compensation inhibit 42 — O Not used (open) 43 RSTO O Reset signal output to the CD text decoder (IC303) 44 BUSY I Busy signal input from the CD text decoder (IC303) Ground terminal (for A/D conversion) “L”: inhibit (fixed at “H”) “L”: reset 45 REQ I Request signal input from the CD text decoder (IC303) 46 GRSCOR I Subcode sync detection signal input from the D-RAM controller (IC401) 47 EEDATA I/O Two-way data bus with the EEPROM (IC302) 48 CCLK O Serial data transfer clock signal output to the CD text decoder (IC303) 49 CSO O Serial data output to the CD text decoder (IC303) 50 CSI I Serial data input from the CD text decoder (IC303) 51 SCK I Serial data transfer clock signal input from the bus interface (IC951) (for SONY bus) 52 SI I Serial data input from the bus interface (IC951) (for SONY bus) 53 SO O Serial data output to the bus interface (IC951) (for SONY bus) 54 BUSON I Bus on/off control signal input from the bus interface (IC951) (for SONY bus) “L”: bus on (used also to reset standby) 55 EJTKEY I Eject switch (SW11) input terminal 56 SCOR I Subcode sync (S0+S1) detection signal input from the digital signal processor (IC501) 57 EEINIT I Initial reset input of the EEPROM 58 — O Not used (open) 59 — O Not used (open) 60 WUP I Key wake-up input terminal In this set, the signal from EJECT switch (SW11) and bus on signal from the bus interface (IC951) (for SONY bus) are input 61 LOCK I Detection input from the magazine lock detect switch (SW802) 62 EHS I Elevator height detection signal input terminal 63 OPEN I Detection input from the door open/close detect switch (SW12) “H”: door open, “L”: door close 64 B.U.CHECK I Backup power supply detection signal input terminal (used also to reset standby) 65 SQCK O Clock signal output for subcode Q data reading to the digital signal processor (IC501) 66 SUBQ I Subcode Q data input from the digital signal processor (IC501) 67 — O Not used (open) 68 CDCLK O Serial data transfer clock signal output to the D-RAM controller (IC401) and digital signal processor (IC501) 69 CDXLT O Serial latch signal output to the digital signal processor (IC501) 70 CDDATA O Serial data output to the D-RAM controller (IC401) and digital signal processor (IC501) 71 SCLK O Clock signal output for SENS serial data reading to the digital servo processor (IC601) 72 VDD — Power supply terminal (+5V) 73 NC I Not used (fixed at “H”) 74 A-MUTE O Audio mute on/off control signal output terminal 75 FOK I Focus OK signal input from the digital servo processor (IC601) – 64 – “L”: initial reset (fixed at “L”) “H”: mute “H”: magazine lock Not used (open) “L”: NG, “H”: OK Pin No. Pin Name I/O Function 76 GFS I Guard frame sync signal input from the digital signal processor (IC501) “L”: NG, “H”: OK 77 SENS I Count sense signal input from the digital signal processor (IC501) 78 — O 79 — O 80 — O Not used (open) *1 Elevator up/down motor, disc load/save motor control Operation Elevator up/down motor (M501) Disc load/save motor (M502) Elevator up Elevator down Disc load Disc save MA (pin 8) “L” “H” “L” “H” MB (pin 7) “L” “L” “H” “H” MC (pin 6) “H” “H” “L” “L” Terminal – 65 – CHANGER BOARD IC303 CXP83413-035Q (CD TEXT DECODER) Pin No. Pin Name I/O Function 1 NC O 2 NC O Not used (open) 3 NC I Not used (fixed at “L”) 4 REQ O Request signal output to the system controller (IC301) 5 CCLK I Serial data transfer clock signal input from the system controller (IC301) Not used (open) 6 CSI I Serial data input from the system controller (IC301) 7 CSO O Serial data output to the system controller (IC301) 8 SCLK O Clock signal output for subcode data reading to the digital signal processor (IC501) 9 SSI I Subcode data input from the digital signal processor (IC501) 10 NC O Not used (open) 11 ADD0 O 12 ADD1 O 13 ADD2 O 14 ADD3 O 15 ADD4 O 16 ADD5 O 17 ADD6 O 18 ADD7 O 19 RAMSEL I 20 DATA0 I/O 21 DATA1 I/O 22 DATA2 I/O 23 DATA3 I/O 24 DATA4 I/O 25 DATA5 I/O 26 DATA6 I/O 27 DATA7 I/O 28 RST I System reset signal input from the system controller (IC301), reset signal generator (IC903), and bus interface (IC951) (for SONY bus) “L”: reset For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H” 29 EXTAL I System clock input terminal (10 MHz) 30 XTAL O System clock output terminal (10 MHz) 31 VSS — Ground terminal 32 to 55 NC O Not used (open) 56 BUSY O Busy signal output to the system controller (IC301) 57 to 59 NC O Not used (open) 60 ADD16 O Address signal output to the S-RAM (IC304) 61 NC O Not used (open) 62 CE O Chip enable signal output to the S-RAM (IC304) 63 WE O Write enable signal output to the S-RAM (IC304) 64 ADD8 O 65 ADD9 O 66 ADD10 O 67 ADD11 O 68 ADD12 O 69 ADD13 O Address signal output to the S-RAM (IC304) Not used (open) Two-way data bus with the S-RAM (IC304) Address signal output to the S-RAM (IC304) – 66 – Pin No. Pin Name I/O 70 VDD — Power supply terminal (+5V) Function 71 NC O Not used (open) 72 NC I Not used (fixed at “L”) 73 NC I Not used (fixed at “H”) 74 ADD14 O Address signal output to the S-RAM (IC304) 75 ADD15 O Address signal output to the S-RAM (IC304) 76 SCOR I Subcode sync (S0+S1) detection signal input from the digital signal processor (IC501) 77 WFCK I Write frame clock (7.35 kHz) signal input from the digital signal processor (IC501) 78 BUCK I Backup power supply detection signal input terminal (used also to reset standby) 79 NC I Not used (fixed at “L”) 80 NC I Not used (fixed at “L”) – 67 – DSP BOARD IC101 CXD2711Q (DIGITAL SIGNAL PROCESSOR FOR FRONT/REAR SPEAKER) IC201 CXD2711Q (DIGITAL SIGNAL PROCESSOR FOR SUB-WOOFER SPEAKER) Pin No. Pin Name I/O 1 VSS — Ground terminal Function 2 CRDY O Output of ready signal at serial data transfer to the master controller (IC301) The start cause interruption occurs by a falling edge 3 CCNT I Input of control/data from address bus for the master controller (IC301) “L”: data input 4 XCWR I Strobe signal input for data writing from the master controller (IC301) Data are written by a falling edge 5 XCRD I Strobe signal input for data reading from the master controller (IC301) “L”: data read 6 VDD — Power supply terminal (+3.3V) 7 CD0 I/O Two-way data bus (LSB) with the master controller (IC301) 8 CD1 I/O 9 CD2 I/O 10 CD3 I/O 11 VSS — 12 CD4 I/O 13 CD5 I/O 14 CD6 I/O 15 CD7 I/O Two-way data bus (MSB) with the master controller (IC301) 16 VDD — Power supply terminal (+3.3V) 17 MUTE I Mute control signal input of the audio data “L”: mute Not used (fixed at “H”) 18 CCS I Input of chip select signal from address bus for the master controller (IC301) 19 VSS — Ground terminal 20 MCKO O Master clock signal (18.432 MHz) output terminal Not used (open) 21 VSS — Ground terminal 22 XTO O System clock signal (33.8688 MHz) output terminal Not used (open) 23 XTI I System clock signal (33.8688 MHz) input terminal 24 VSS — Ground terminal 25 (BIST) O Output terminal for the test Not used (open) 26 (TCK) O Output terminal for the test Not used (open) 27 (TDI) O Output terminal for the test Not used (open) 28 (TENA1) O Output terminal for the test Not used (open) 29 (TDO) O Output terminal for the test Not used (open) 30 (VST) I Input terminal for the test Not used (fixed at “L”) 31 VSS — 32 RESET I Reset signal input from the master controller (IC301) “L”: reset 33 BCLK O Block clock signal output terminal Not used (open) 34 LRCK I L/R sampling clock signal (44.1 kHz) input of the serial in/out data 35 BCK I Bit clock signal (2.8224 MHz) input of the serial in/out data 36 VSS — 37 SIA I Serial audio data input terminal IC101: Serial data (for front speaker) input from the CXD2710R (IC601) IC201: Serial data (for sub-woofer speaker) input from the CXD2710R (IC601) 38 SIB I Serial audio data input terminal IC101: Serial data (for rear speaker) input from the CXD2710R (IC601) IC201: Not used (fixed at “L”) Two-way data bus with the master controller (IC301) Ground terminal Two-way data bus with the master controller (IC301) Ground terminal Ground terminal – 68 – Pin No. Pin Name I/O Function 39 SOA O Serial audio data output terminal IC101: Serial data (for front speaker) output terminal IC201: Serial data (for sub-woofer speaker) output terminal 40 SOB O Serial audio data output terminal IC101: Serial data (for rear speaker) output terminal IC201: Not used (open) 41 VSS — Ground terminal 42 TST1 I Input terminal for the test Not used (fixed at “L”) 43 TST2 I Input terminal for the test Not used (fixed at “L”) 44 TST3 I Input terminal for the test Not used (fixed at “L”) 45 TST4 I Input terminal for the test Not used (fixed at “L”) 46 VDD — 47 TST5 I Input terminal for the test Not used (fixed at “L”) 48 TST6 I Input terminal for the test Not used (fixed at “L”) 49 VSS — Ground terminal 50 MD00 I/O IC101: Two-way data bus (LSB) with the D-RAM (IC102) IC201: Two-way data bus (LSB) with the D-RAM (IC202) 51 VSS — Ground terminal 52 MD01 I/O 53 MD02 I/O 54 MD03 I/O Power supply terminal (+3.3V) IC101: Two-way data bus with the D-RAM (IC102) IC201: Two-way data bus with the D-RAM (IC202) 55 VSS — 56 MD04 I/O 57 MD05 I/O 58 MD06 I/O 59 MD07 I/O 60 VDD — Power supply terminal (+3.3V) 61 VSS — Ground terminal 62 MD08 I/O 63 MD09 I/O 64 MD10 I/O 65 MD11 I/O Ground terminal IC101: Two-way data bus with the D-RAM (IC102) IC201: Two-way data bus with the D-RAM (IC202) IC101: Two-way data bus with the D-RAM (IC102) IC201: Two-way data bus with the D-RAM (IC202) 66 VDD — 67 MD12 I/O 68 MD13 I/O 69 MD14 I/O 70 MD15 I/O IC101: Two-way data bus (MSB) with the D-RAM (IC102) IC201: Two-way data bus (MSB) with the D-RAM (IC202) 71 VSS — Ground terminal 72 RAS O IC101: Row address strobe signal output to the D-RAM (IC102) IC201: Row address strobe signal output to the D-RAM (IC202) 73 MA09 O 74 MA10 O 75 MA11 O 76 VDD — Power supply terminal (+3.3V) 77 MA12 O Address signal output terminal Power supply terminal (+3.3V) IC101: Two-way data bus with the D-RAM (IC102) IC201: Two-way data bus with the D-RAM (IC202) Address signal output terminal Not used (open) Not used (open) – 69 – Pin No. Pin Name I/O 78 MA13 O Function 79 MA14 O 80 MA15 O 81 VSS — Ground terminal 82 MA00 O 83 MA01 O IC101: Address signal output to the D-RAM (IC102) IC201: Address signal output to the D-RAM (IC202) 84 VSS — Ground terminal 85 MA02 O 86 MA03 O IC101: Address signal output to the D-RAM (IC102) IC201: Address signal output to the D-RAM (IC202) 87 VDD — Power supply terminal (+3.3V) 88 MA04 O 89 MA05 O IC101: Address signal output to the D-RAM (IC102) IC201: Address signal output to the D-RAM (IC202) 90 VSS — Ground terminal 91 VSS — Ground terminal 92 MA06 O 93 MA07 O IC101: Address signal output to the D-RAM (IC102) IC201: Address signal output to the D-RAM (IC202) 94 VSS — Ground terminal 95 MA08 O IC101: Address signal output to the D-RAM (IC102) IC201: Address signal output to the D-RAM (IC202) 96 MA16 O Address signal output terminal Not used (open) 97 MA17 O Address signal output terminal Not used (open) 98 VDD — Power supply terminal (+3.3V) 99 WE O IC101: Write enable signal output to the D-RAM (IC102) IC201: Write enable signal output to the D-RAM (IC202) 100 OE O IC101: Output enable signal output to the D-RAM (IC102) IC201: Output enable signal output to the D-RAM (IC202) 101 VSS — Ground terminal 102 ROM-CE O Chip enable signal output terminal Not used (open) 103 CAS O IC101: Column address strobe signal output to the D-RAM (IC102) IC201: Column address strobe signal output to the D-RAM (IC202) 104 VSS — Ground terminal 105 DEND O Internal operation monitor output terminal Not used (open) 106 VDD — Power supply terminal (+3.3V) 107 PEND O Internal operation monitor output terminal Not used (open) 108 ENC0 O 109 ENC1 O 110 ENC2 O 111 VSS — Ground terminal 112 STOP O Internal operation monitor output terminal Not used (open) 113 HOLD O Internal operation monitor output terminal Not used (open) 114 OVF O Overflow monitor output terminal at the operation “H”: overflow Not used (open) 115 LIM O Fixed/float conversion limiter output terminal “H”: limiter on Not used (open) 116 BTIA I Bit input terminal Not used (fixed at “L”) Address signal output terminal Not used (open) Internal operation monitor output terminal Not used (open) 117 BTIB I Bit input terminal Not used (fixed at “L”) 118 BTOA O Bit output terminal Not used (open) 119 BTOB O Bit output terminal Not used (open) 120 VDD — Power supply terminal (+3.3V) – 70 – DSP BOARD IC301 HD6473048-DSP01 (MASTER CONTROLLER) Pin No. Pin Name I/O 1 VDD — Power supply terminal (+5V) Function 2 PW-ON O Output of power on/off control signal for the system power supply (digital/analog power supply, amp remote etc.) “H”: power on 3 S-OUT O Serial data output to the EEPROM (IC302), input selector (IC415), digital signal processor (IC601 CXD2710R), and electrical volume (IC1106, 1206, 1306) 4 S-CKO O Serial data transfer clock signal output to the input selector (IC415), digital signal processor (IC601 CXD2710R), and electrical volume (IC1106, 1206, 1306) 5 DSPRST O Reset signal output to the digital signal processor (IC101, 201 CXD2711Q/IC601 CXD2710R), and digital filter (IC1101, 1201, 1301) “L”: reset 6 2710-CE O Chip enable signal output to the digital signal processor (IC601 CXD2710R) 7 EE-CKO O Serial data transfer clock signal output to the EEPROM (IC302) 8 SP-CE O Chip enable signal output to the input selector (IC415) 9 DSP-RDY I Input of ready signal at data transfer from the digital signal processor (IC101, 201 CXD2711Q) The start cause interruption occurs by a falling edge Not used (fixed at “L”) 10 VPP I 11 GND — Ground terminal 12 S-OUT (TX) O UART (Universal Asynchronous Receiver/Transmitter) transmit output of the master bus controller (CN12) 13 UNISO O Serial data output to the bus interface (IC306) (for SONY bus) 14 S-IN (RX) I UART (Universal Asynchronous Receiver/Transmitter) receive input of the master bus controller (CN12) 15 UNISI I Serial data input from the bus interface (IC306) (for SONY bus) 16 NIL I Not used (fixed at “L”) 17 UNICKI I Serial data transfer clock signal input from the bus interface (IC306) (for SONY bus) 18 D0 I/O 19 D1 I/O 20 D2 I/O 21 D3 I/O 22 VSS — 23 D4 I/O 24 D5 I/O 25 D6 I/O 26 D7 I/O 27 D8 I/O 28 D9 I/O 29 D10 I/O 30 D11 I/O 31 D12 I/O 32 D13 I/O 33 D14 I/O 34 D15 I/O 35 VDD — Power supply terminal (+5V) 36 A0 O Address signal output terminal In this set, the chip enable signal output to the digital signal processor (IC101 CXD2711Q) 37 A1 O Address signal output to the flash memory (IC401, 402), and chip enable signal output to the digital signal processor (IC201 CXD2711Q) Two-way data bus with the flash memory (IC401) Ground terminal Two-way data bus with the flash memory (IC401) Two-way data bus with the digital signal processor (IC101, 201 CXD2711Q) and flash memory (IC402) – 71 – Pin No. Pin Name I/O Function 38 A2 O 39 A3 O 40 A4 O 41 A5 O 42 A6 O 43 A7 O 44 VSS — 45 A8 O 46 A9 O 47 A10 O 48 A11 O 49 A12 O 50 A13 O 51 A14 O 52 A15 O 53 A16 O 54 A17 O 55 A18 O 56 A19 O 57 VSS — Ground terminal 58 MUTE O Relay drive signal output for the speaker protect relay (RY1101, 1201, 1301) At output of “L”, the relay is turned on to apply muting 59 SMUTE O Soft mute control signal output to the electrical volume (IC1106, 1206, 1306) “H”: mute on 60 EMP-O O Emphasis control signal output to the digital filter (IC1101, 1201, 1301) “H”: emphasis on 61 NCO O System clock signal output terminal Not used (open) 62 STBY I Standby signal input terminal Fixed at “H” in this set 63 SYSRES I System reset signal input from the reset signal generator (IC303) and bus interface (IC306) (for SONY bus) “L”: reset For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H” 64 BU-IN I Backup power supply detect signal input terminal (used also to reset standby) 65 VSS — Address signal output to the flash memory (IC401, 402) Ground terminal Address signal output to the flash memory (IC401, 402) Ground terminal 66 X-IN I System clock input terminal (14.74 MHz) 67 EX-IN I System clock input terminal (14.74 MHz) 68 VDD — Power supply terminal (+5V) 69 AS O Address strobe signal output terminal Not used (open) 70 RD O Strobe signal output for data reading to the digital signal processor (IC101, 201 CXD2711Q) and flash memory (IC401, 402) 71 HWR O Strobe signal output for upper byte data writing to the digital signal processor (IC101, 201 CXD2711Q) and flash memory (IC402) 72 LWR O Strobe signal output for lower byte data writing to the flash memory (IC401) 73 MD0 I Input terminal for setting microcomputer operation mode (fixed at “L”) 74 MD1 I Input terminal for setting microcomputer operation mode (fixed at “H”) 75 MD2 I Input terminal for setting microcomputer operation mode (fixed at “H”) 76 AVDD — 77 AVREF I Reference voltage input terminal (+5V) (for A/D conversion) 78 NIH I Fixed at “H” in this set Power supply terminal (+5V) (for A/D conversion) – 72 – Pin No. Pin Name I/O Function 79 DIR-ERR I PLL unlock error detection signal input from the digital audio interface receiver (IC502) “H”: error 80 EMP-IN I Emphasis detection signal input from the digital signal processor (IC501 CXD2540Q) and digital audio interface receiver (IC502) “H”: emphasis on 81 VOLMAX I Input terminal for the test mode 82 DSP-BUSY I Input of busy signal at serial data transfer from the digital signal processor (IC601 CXD2710R) 83 DSP-PLL I Not used (fixed at “L”) Not used (fixed at “L”) 84 BU-IN I Backup power supply detection signal input terminal (used also to reset standby) 85 DSP-SI I Serial data input from the digital signal processor (IC601 CXD2710R) 86 AVSS — 87 BUS-ON I Bus on/off control signal input from the bus interface (IC306) (for SONY bus) With the bus in off status, standby is cancelled by bus on falling edge 88 2711-CE O Chip enable signal output to the digital signal processor (IC101, 201 CXD2711Q) 89 FROM-CE2 O Chip enable signal output to the flash memory (IC401, 402) 90 FROM-CE1 O Chip enable signal output to the flash memory (IC401, 402) 91 BOOT I Input of forced boot mode detection activated 92 VSS — Ground terminal 93 LINKOFF1 O Bus on/off control signal output to the bus interface (IC951) (for SONY bus) 94 TEND O Not used (open) 95 LINKOFF2 O Bus on/off control signal output for the AUX bus control 96 LINKOFF3 O Bus on/off control signal output terminal 97 VOLCE0 O Chip enable signal output to the electrical volume (IC1106) (for front speaker) 98 VOLCE1 O Chip enable signal output to the electrical volume (IC1206) (for rear speaker) 99 VOLCE2 O Chip enable signal output to the electrical volume (IC1306) (for sub-woofer speaker) 100 A20 O Address signal output to the flash memory (IC401, 402), and control/data output to the digital signal processor (IC101, 201 CXD2711Q) Ground terminal (for A/D conversion) – 73 – “L”: bus on At the reset, if “H” is entered, the boot mode is forcibly “L”: bus on “L”: bus on “L”: bus on Not used (open) DSP BOARD IC601 CXD2710R (DIGITAL SIGNAL PROCESSOR) Pin No. Pin Name I/O 1 AMPIN I Loop filter amplifier input for the PLL Not used (fixed at “L”) Function 2 AMPOUT O Loop filter amplifier output for the PLL Not used (open) 3 VDD — Power supply terminal (+5V) 4 VSS — Ground terminal 5 AVSS1 — Ground terminal (for A/D conversion) 6 VCOC I 7 AVDD1 — Power supply terminal (+5V) (for A/D conversion) 8 VCOOUT O Signal output of the internal VCO Not used (open) 9 MCK1 (768FS) I Master clock signal (768Fs) input terminal Not used (fixed at “H”) 10 MCK2 (384FS) I Master clock signal (384Fs) input terminal 11 MCKOUT O Master clock signal output terminal Not used (open) 12 MCKSEL I Input terminal for clock signal setting internal VCO or MCK2 (pin !º) Internal VCO used: “L”, MCK2 (pin !º) used: “H” (fixed at “H”) 13 MUTE I Mute signal input of the serial interface Not used (fixed at “H”) Program data serial input from the master controller (IC301) Control signal input for the internal VCO Not used (fixed at “L”) 14 DIN I 15 VSS — 16 SCK I Program data transfer clock signal input from the master controller (IC301) 17 CE I Program data load input from the master controller (IC301) 18 DOUT O Serial data output to the master controller (IC301) 19 BUSY O Busy signal at serial data transfer output to the master controller (IC301) 20 RESET I Reset signal input from the master controller (IC301) “L”: reset 21 to 27 TEST I Not used (fixed at “L”) 28 VDD — Power supply terminal (+5V) 29 VSS — Ground terminal 30 to 38 TEST I Not used (fixed at “L”) Ground terminal 39 M1 O Parallel data (LSB) output terminal Not used (open) 40 VSS — Ground terminal 41 M2 O 42 M3 O 43 M4 O 44 M5 O 45 M6 O 46 M7 O 47 M8 O 48 M9 O 49 M10 O 50 M11 O 51 M12 O 52 M13 O 53 VDD — Power supply terminal (+5V) 54 VSS — Ground terminal 55 M14 O Parallel data output terminal Not used (open) 56 M15 O Parallel data output terminal Not used (open) 57 M16 O Parallel data (MSB) output terminal Not used (open) Parallel data output terminal Not used (open) – 74 – Pin No. Pin Name I/O Function 58 to 64 TEST O Not used (open) 65 VSS — Ground terminal 66 to 74 TEST O Not used (open) 75 EBDIR I Not used (fixed at “L”) 76 UBDIR I Not used (fixed at “L”) 77 D.SEL1 I Input terminal for data output setting serial out or parallel out (fixed at “L”) 78 VDD — Power supply terminal (+5V) 79 VSS — Ground terminal 80 D.SEL2 I Input terminal for data output setting serial out or parallel out (fixed at “L”) 81 TEST I Not used (fixed at “L”) 82 TEST I Not used (fixed at “L”) 83 AVDD2 — Power supply terminal (+5V) (for A/D conversion) 84 AVSS2 — Ground terminal (for A/D conversion) 85 AVDD3 — Power supply terminal (+5V) (for A/D conversion) 86 AVSS3 — Ground terminal (for A/D conversion) 87 S3OUT O Serial data (1 sampling, 2 channel) output for the sub-woofer speaker 88 S2OUT O Serial data (1 sampling, 2 channel) output for the rear side speaker 89 S1OUT O Serial data (1 sampling, 2 channel) output for the front side speaker 90 VSS — Ground terminal 91 S3DI AD I Serial data (1 sampling, 2 channel) input for the tuner or external analog audio signal (ANALOG IN AUX AUDIO) 92 S2DI DIR I Serial data (1 sampling, 2 channel) input for the external digital audio signal (DIGITAL IN AUX AUDIO) 93 S1DI CD I Serial data (1 sampling, 2 channel) input for the CD 94 BCK I Bit clock signal (2.8224 MHz) input of the serial in/out data 95 LRCK I L/R sampling clock signal (44.1 kHz) input of the serial in/out data 96 LOCK O Error signal output of the PLL phase comparator Not used (open) 97 V O Divider output for the PLL 98 VAR I PLL phase comparator variable input terminal 99 REF I PLL phase comparator reference input terminal Not used (fixed at “L”) 100 PD O PLL phase comparator charge pump input terminal Not used (open) – 75 – 7-2. IC201 (BA6247FP-Y) MOTOR DRIVER IC OPERATION (DRIVER BOARD) The elevator up/down motor connected between pin @™ and pin !• of IC201 is as M501, and the disc load/save motor connected between pin 1 and pin !• of IC201 is as M502. When the IC port logic is pin @™ > pin !•, pin 1 > pin !•, the rotating direction of M501 and M502 becomes normal. ROTATION TRUTH TABLE 1 When MB=MC: both M501 and M502 are stop. (MA value is free.) 2 When MB≠MC: Rotating direction of motor Pin of IC301 MA (pin 8) MB (pin 7) MC (pin 6) M501 M502 “L” “L” “H” Reverse Stop “H” “L” “H” Normal “L” “H” “L” Stop “H” “H” “L” Stop Normal Pin of IC201 pin @™ pin 1 pin !• “L” OPEN “H” Elevator up Stop “H” OPEN “L” Elevator down Reverse OPEN “L” “H” Disc load OPEN “H” “L” Disc save Disc load/save M502 (1–18) Operation Elevator up/down 1 !• !• @™ – 76 – M501 (22–18) XES-Z50 XES-Z50 BLOCK DIAGRAM – CONTROL UNIT (TUNER Section) – CN502 (1/2) (ANTENNA) • Signal path. –1 L-CH 13 FM R-CH 8 –2 MAIN (FM/AM) : FM L-CH TO CD CHANGER : AM R-CH MUTE Q605, 606 MAIN ANT FM/AM TUNER UNIT SUB (FM) L-CH MUTE CONTROL SWITCH Q607 SUB ANT AM R-CH 2 MUTE A (Page 82) MUTE AM MODE FM MODE SD S.METER SEEK DIVER PLL4 PLL3 PLL2 PLL1 Q519 IC603 FM/AM SELECT RELAY IC506 SWITCHING 4 SIGNAL METER BUFFER Q541 1 Q526 RELAY DRIVE Q609 Q525 73 72 63 57 56 71 32 70 66 DIVER SEEK FM VSM AM VSM SD ST /MONO MUTE AM ST IN 41 40 39 38 MAIN/SUB TUNER B+ PLL CE PLL CKO PLL DO PLL DI TUNER CONTROLLER IC502(1/2) AM B+ FM/AM TUNER UNIT B+ AM B+ SWITCH Q536, 538 FM B+ FM/AM TUNER UNIT B+ AM B+ SWITCH Q535, 537 TUNER CIRCUIT B+ TUNER B+ SWITCH Q528, 529 AM ON 64 X2 EEP SDA EEP SCK SRAM RST FM ON 65 X1 8 9 30 26 52 P.U +5V TU ON 61 X503 8MHz EEPROM IC516 – 77 – 5 6 SCL 05 SDA 7-3. RESET SIGNAL GENERATOR IC517 B.U +5V – 78 – XES-Z50 BLOCK DIAGRAM – CONTROL UNIT (DISPLAY Section) DATA LEVEL SHIFT IC941 RST 14 RX-LCD 63 RES 67 XTAL BZ811 (BUZZER) BUZZER DRIVE Q811 97 BEEP 96 DEC-CLR 89 DEC-CS 90 DEC-INT D8 – D15 D0 – D15 SIRCS C (Page 81) D (Page 81) LCD-DAT 0 LCD-DAT 7 A0 36 66 EXTAL X901 14.745MHz DSPL-ON 5 SIRCS LCD-CONT A1 – A19 DATABUS BUS DATA RST DATA TRANSCEIVER IC507 12 TX-LCD ADDRESS ADDRESSBUS BUS DSPL-RST 4 DATA BUFFER IC942 (1/2) D0 – D15 LEVEL SHIFT IC509 18 – 21, 23 – 34 D0 – D15 LCD-TX 12 LIQUID CRYSTAL DISPLAY MODULE DISPLAY CONTROLLER IC901 LCD-RX 14 A1 – A18 A1 – A18 37 – 43, 45 – 55 DATA BUS ADDRESS BUS D0 – D15 18 – 21, 23 – 34 DISPLAY CONTROLLER IC802 (1/2) A1 – A19 37 – 43, 45 – 56 7-4. SWITCHING IC951 (1/2) LCD-BUSY 9 2 TIR LCD-BUSY LCD-START 8 GATE SWITCH IC807 (1/3) LB 72 LWR 72 LWR GATE SWITCH IC921 (1/3) 71 HWR LCD RST 95 71 HWR DIMER 85 GATE SWITCH IC807 (2/3) LB GATE SWITCH IC921 (2/3) DIMER CONTR 84 CONTR RV801 UB GATE SWITCH IC807 (3/3) UB CONTRAST GATE SWITCH IC921 (3/3) LCD-CS 99 SWITCHING IC951 (2/2) 70 RD LCD-LAT 70 RD GATE SWITCH IC803 ADDRESS BUS 56 A19 90 ROM-CS 88 SRAM-CS 91 ROM-CS 88 SRAM-CS DATA BUS ADDRESS BUSBUS ADDRESS X802 14.745MHz DATA DATA BUSBUS CE 39 LB 28 26 40 UB 6 CE 41 OE 17 WE DSPL-ON WE 17 OE 41 LB 39 UB 40 CE 6 05 A1 – A19 DQ0 – DQ15 A1 – A16 D0 – D15 25 – 18, 8 – 1, 48, 17,16 OE A0 – A15 WE 11 D0 – D15 FLASH MEMORY IC931 I/O1 – I/O16 S-RAM IC932 29, 31, 33, 35, 38, 40, 42, 44, 30, 32, 34, 36, 39, 41, 43, 45 67 A0 – A18 A1 – A18 D0 – D15 XTAL 66 7 – 10, 13 – 16, 29 – 32, 35 – 38 DQ0 – DQ15 29, 31, 33, 35, 38, 40, 42, 44, 30, 32, 34, 36, 39, 41, 43, 45 A0 – A17 EXTAL 25 – 18, 8 – 1, 48, 17 A1 – A16 D0 – D15 I/O1– I/O16 7 – 10, 13 – 16, 29 – 32, 35 – 38 A0 – A15 5 – 1, 44 – 42, 27 – 24, 21 – 18 FLASH MEMORY IC804 5 – 1, 44 – 42, 27 – 24, 21 – 18 S-RAM IC805 26 CE 28 OE 11 WE B (Page 82) – 79 – KEY-CONT – 80 – KEYCONT XES-Z50 3 9 5 4 11 6 B+ DSP-DATA LCD-DATA RESET SIRCS BUFFER Q521 BUS CLK BUFFER IC942 (2/2) SIRCS SIRCS BUS ON C 7 1 DISPLAY CONTROLLER IC802 (2/2) CN502 (2/2) (TO CD CHANGER) D519 4 D515 TEL-MUTE LINK-OFF 94 BUS ON SWITCH Q516 TUNER CONTROLLER IC502 (2/2) D540 D520 BATT RESET OUT DATA I/O 12 8 9 D507 BU-C 5 BATTERY CHECK SWITCH Q515 TUNER B+ FM/AM TUNER UNIT B+ D523 RESET SIGNAL GENERATOR IC504 UNISI 15 UNICKI 17 SYSRES 63 REGULATOR Q507 S42 (RESET) +9V REGULATOR IC505 +9V FM/AM TUNER UNIT B+ X501 32.768kHz B+ SWITCH Q501, 502 S51 (RESET) MUTE MECHA ON 76 77 80 1 78 79 32 50 5 6 KEY ACTIVE SWITCH Q522 P.U +5V S23 56 PNL SW2 OFF S3 11 12 SWITCHING IC51 (2/2) 4 S1, 2 FRONT PANEL DESORPTION DET 55 PNL SW3 – 81 – 5 3 7 S41 (NOSE DET) CONNECTOR BOX & DISPLAY HOLDER SECTION REGULATOR Q542 +5V DISPLAY CIRCUIT B+ +5V REGULATOR IC510 B+ SWITCH Q509, 510 2 CN508 LED B+ TO ROTARY COMMANDER (RM-X66) SCHMITT TRIGGER IC31 05 6 B+ SWITCH Q532, 533 +9 V S1 RESET SW 13 NOSE SW 64 D556 RC-IN1 57 PNL SW1 S2 SWITCHING IC51 (1/2) +9V RC-IN0 S22 TUNER ON IC501, 502 V.REF. ENC – 53 FG PNL SW4 54 S21 REGULATOR Q511 REGULATOR SWITCH Q512, 513 KEY ILL 45 MECHA +5V D577 SCHMITT TRIGGER IC513 +9V ROTARY COMMANDER B.U +5V P.U +5V 59 PNL M+ EEPROM IC515 FRONT PANEL DESORPTION MOTOR ROTATION DETECT PH21 ANT REM TEL MUT AUX ON RESET BU IN RC IN1 65 RC IN0 22 ENC – 12 ENC + 13 KEY IN1 58 PNL M– 49 LIQUID CRYSTAL DISPLAY MODULE +30V +30V REGULATOR Q803 LCD B+ (FOR BACK LIGHT) DC/DC CONVERTER CIRCUIT IC801, Q801, 802 +9V REGULATOR IC511 DSPL-ON 5 OPEN CLOSE KEY IN0 6 SYSTEM CONTROLLER IC501 ACC IN 29 66 63 48 60 62 SYS RST UNICKI UNICKO UNISO UNISI XT2 XT1 21 MUTE IN1 KEY ACK IN2 MOTOR DRIVE FRONT PANEL DESORPTION MOTOR DRIVE IC11 S21 – 23 FRONT PANEL POSITION DET 19 18 ENC + M1 FRONT PANEL DESORPTION 17 KEY CONT 2 OUT1 SCL M KEY ACT VREF OUT2 EEP SCK 4 10 16 61 SIRCS EEP SDA MECHA +5V X2 X1 REFERENCE VOLTAGE SWITCH Q11 20 72 73 BUS ON 69 70 D A B (Page 80) (Page 78) (Page 79) – 82 – 3 BATTERY CN501 POWER SUPPLY CONNECTOR REGULATOR SWITCH Q505, 506 D522 X502 5MHz L501, L506 PLL B+ FM/AM TUNER UNIT B+ BU-IN 64 BU-IN 84 LCD-BLON 93 ANT-REM REGULATOR Q508 B.U +5V CONNECTOR BOX & DISPLAY HOLDER SECTION D521 LEVEL SHIFT IC808 ACCESSORY D514 BUS ON 87 LEVEL SHIFT Q517 AUX-ON ANTENNA REMOTE SWITCH Q503, 504 10 LEVEL SHIFT Q518 UNISO 13 2 ACCESSORY CHECK Q520 BUS INTERFACE (FOR SONY BUS) IC503 BATTERY SWITCH 13 11 1 REMOTE IN SWITCH Q530 3 RST IN 44 14 16 CLK OUT 42 2 4 CLK IN UNICKI RESET BU IN 46 DATA OUT UNIREQ 45 BUS ON OUT UNISO 17 6 RESET SWITCH BUS ON IN UNISI 1 DATA IN 2 SIRCS 3 SIRCS SDA (Page 80) BUS DATA BLOCK DIAGRAM – CONTROL UNIT (BUS CONTROL/POWER SUPPLY Section) – BUSON 7-5. XES-Z50 BLOCK DIAGRAM – CHANGER UNIT (CD Section (1/2)) – 24 RF MIX 16 ASYI 26 FE BIAS F I-V AMP DETECTOR TRACKING ERROR AMP E I-V AMP 12 TRACKING OFFSET AUTOMATIC POWER CONTROL Q101 LD 1 LD APC LD AMP APC PD AMP PD PCO CLTV FILI SUBCODE Q PROCESSOR 31 32 19 67 PRIORITY ENCODER DOUT XTAO XTAI 2 SERVO AUTO SEQUENCER SUBCODE P-W PROCESSOR 66 65 64 61 GTOP, RFCK, RAOF 1 (Page 85) 2 (Page 85) 3 (Page 85) 4 (Page 87) 5 (Page 85) 6 (Page 85) 7 (Page 85) 8 (Page 85) 42 FSTT SQCK LDON 63 62 DATA, BCLK 34 35 39 43 45 C16M 2 3 4 5 6 LASER DIODE ADDRESS GENERATOR CLV PROCESSOR EO 13 RV101 CLOCK GENERATOR 14 FSW MON MDP MDS LOCK EI OPTICAL PICK-UP (KSS-400A) TIMING GENERATOR 2 SQSO E 7 TE TIMING GENERATOR 1 WDCK LRCK 6 RV102 FOCUS BIAS DIGITAL OUT ERROR CORRECTOR 32K RAM SCOR F ASYO 27 DATA BCLK GTOP RFCK RAOF GFS PEAK DETECTOR SYNC PROTECTOR WFCK F 15 INTERNAL BUS EXCK FE FOCUS ERROR AMP D/A DATA PROCESSOR REGISTER ASYMMETRY CORRECTION C PD EFM DEMODULATOR 60 54 X502 16.93MHz 53 C16M FLIP-FLOP IC502 58 56 CPU INTERFACE 76 75 77 79 78 80 1 69 68 DATA CLOK XLAT 17 SERIAL/ PARALLEL PROCESSOR MUTE RFO DIGITAL PLL VARI-PITCH DOUBLE SPEED CNIN SEIN DATAO CLKO XLTO MIRR FOK SENS PD2 4 RF SUMMING AMP 19 EMPH RF I-V AMP 20 22 SBSO D B DIGITAL SIGNAL PROCESSOR IC501 PD1 3 A 18 FILO VC E FILTER RF AMP, FOCUS/TRACKING ERROR AMP IC101 71 74 72 XRST 70 4 IC305 GATE SWITCH IC252 COMPARATOR IC251 EXCK MDS DE-EMPHASIS 2 SPINDLE MOTOR DRIVE Q252, IC253 MDP WFCK SCOR SBSO M (SPINDLE) SPINDLE MOTOR DRIVE WFCK, SCOR, EXCK, SBSO LRCK DC MOTOR (1/2) TIMING IC505 5 4 7 3 SLED MOTOR DRIVE, FOCUS/TRACKING COIL DRIVE IC202 FOCUS COIL DRIVE FF FR 51 53 TRACKING TR– COIL DRIVE TRF TRR 23 47 24 49 38 40 SLF SLR TFDR TRDR SFDR NOISE SHAPER & PWM MODULATOR CDRST DIGITAL SERVO PROCESS SRDR DATA CLK 20 XLT SCLK DATA, CLK 24 21 23 30 19 JUMP/ SEARCH CONTROL DFCT 14 MIRR 20 FOK 19 MIRR/DFCT/ FOK DETECTOR SYSTEM CONTROLLER IC301 (1/3) ELEVATOR UP/DOWN MOTOR DRIVE, DISC LOAD/SAVE MOTOR DRIVE DC MOTOR (2/2) M501 ELEVATOR UP/DOWN M502 DISC LOAD/SAVE IC201 M M 22 18 1 OUT2 OUT1 OUT3 MOTOR DRIVE IN2 6 IN1 5 IN3 8 7 MB 6 MC 8 MA EHS 62 Q301 DISC EJECT MOTOR DRIVE IC801 M 7 1 OUT2 OUT1 MOTOR DRIVE RIN FIN DOE 17 5 10 M3 4 11 M3 Q302 DPT 16 – 83 – 70 68 69 13 76 19 18 20 21 61 63 9 SW12 ELEVATOR HEIGHT DETECT SENSOR PH101 • Signal path. +5V DOOR OPEN/ CLOSE DET SW802 (MAGAZINE LOCK DET) 05 M801 (DISC EJECT) Q103 75 77 GFS 66 PGR 65 CDRST 56 CD DATA CD CLK CD XLT (LIMIT) 15 FOK 71 SENS 56 SSTP CES PST LOT LOCK OPEN 17 SLED MOTOR S– DRIVE XRST 33 HOME M S+ A/D CONVERTER SUBQ (SLED) 16 FFDR FRDR SQCK 26 TR+ 25 SENS 29 XTAL 15 5 4 (FOCUS) 27 MPX SCOR 12 F+ F– LOCK 18 APC 13 LRCK, WDCK WDCK COUT SCLK (TRACKING) DIGITAL SERVO PROCESSOR IC601 MICRO COMPUTER INTERFACE 2-AXIS DEVICE SE TE FE RF 7-6. DISC DETECT SENSOR Q701 D702 (DOE) DISC DETECT SENSOR Q702 D703 (DPT) SW803 SW501 (HOME/TOP DET) HOME TOP SW804 LINEAR SLIDE LEVER POSITION DET PLUNGER DRIVE Q703, 704 (MAGAZINE DET) SW701 DISC CHUCKING END DET – 84 – PRG401 (MAGAZINE OUT) : CD PLAY XES-Z50 BLOCK DIAGRAM – CHANGER UNIT (CD Section (2/2)) – • Signal path. D-RAM CONTROLLER IC401 : CD PLAY D OUT DIGITAL OUT BCLK LRCK WDCK SELECTOR D/A CONVERTER INTERFACE DATA BCK LRCK GTOP 8 RFCK 7 XROI 6 C4M 5 GTOP RFCK RAOF C16M WFCK 3 SCOR 80 GRSRST 1 GRSCOR 79 TIMING GENERATOR XTAI VWA A0 – A9 ADDRESS MONITOR DATA XQOK LATCH XWRE XRDE XSOE DATA CLK 36 45 37 38 46 47 D1 – D4 1, 2, 24, 25 23 4 3 22 9 – 12, 14 – 18, 5 1, 2, 24, 25 A0 – A9 D1 – D4 RAS CAS WE1 WE2 OE1 OE2 CSO 49 CSI 50 CCLK 48 REQ 45 BUSY 44 6 CSI 7 CSO 5 CCLK 4 REQ 56 BUSY D303 RSTO 43 28 RST CE 62 EEDATA TEMP H TEMP L XTLI XTLO 4 47 38 39 31 32 BU. CHECK 64 78 BUCK – 85 – DATA (Page 93) +5V BATTERY CHECK EEPROM IC302 12 29 WE 22 CE1 30 CE2 24 OE WE 63 RESET 30 5 (Page 93) 12 – 5, 27, 26, 23, 25, 4, 28, 3, 31, 2 A0 – A16 30 XTAL 13 – 15, 17 – 21 D0 – D7 29 EXTAL X302 10MHz XRDE XSOE SDTI XQOK ESPXTL XWRE 9 SSI 8 SCLK 77 WFCK 76 SCOR S-RAM IC304 ADD0 – ADD16 DATA XQOK LATCH XWRE XRDE XSOE SBSO EXCK WFCK SCOR SYSTEM CONTROLLER IC301 (2/3) 6 11 D-RAM IC403 28 24 26 22 23 27 05 (Page 87) 23 4 3 22 CD TEXT DECODER IC303 25 46 10 OE1 WE1 RAS CAS WE2 OE2 WFCK, SCOR, EXCK, SBSO EECLK 5 DATA, CLK CLK (Page 84) 8 GRSRST (Page 84) XRAS XCAS XWE XWE2 XOE XOE2 A0 – A9 9 – 12, 14 – 18, 5 DATA BUS 64 74 60 58 59 63 61 62 SYNC (44.1kHz) ADDRESS BUS 42, 41, 44, 43 SDTO XQOK ESPXLT XWRE XRDE XSOE 2 XRST SDTI SCK D1 – D4 CDRST (Page 87) D-RAM IC402 CPU INTERFACE 7 CLOCK GENERATOR IC503 BUFFER IC504 16 READ/WRITE BASE COUNTER DATA LINKING CONTROL 9 LRCK D-RAM INTERFACE GTOP, RFCK, RAOF WFCK SCOR (Page 84) DATA, BCK, LRCK DATA BCK 24 23 25 11 – 18, 64 – 69, 74, 75, 60 LRCK, WDCK DIGITAL SIGNAL PROCESSOR INTERFACE 20 – 27 3 DATAI 10 BCKI 9 LRCI 11 WDCI 13 DATA0 – DATA7 (Page 84) 2 DATA XCAS XRAS XWE XOE (Page 84) 6 DATA, BCLK XCAS XRAS XWE XOE (Page 84) 1 26 30 – 27, 55 – 53, 51, 50, 31 (Page 84) GRSCORE 7-7. TH301 TH302 X301 8MHz +5V RESET SIGNAL GENERATOR IC903 RST – 86 – XES-Z50 BLOCK DIAGRAM – CHANGER UNIT (MAIN Section (1/2)) – DATA BCK, LRCK 9 (Page 86) MASTER BUS CONTROLLER DATA 8 TUNER R-IN BCK LRCK 13 TUNER L-IN IC417 ISOLATION IC702, IC703 (1/2) BUFFER IC701 (1/2) BCK FROM CONTROL UNIT LRCK 13 9 JK2011 LINE AMP IC1601 L INVERT AMP IC1603 4 AIN L+ + – + AIN L– LOOP FILTER DECIMATION FILTER SERIAL OUTPUT INTERFACE SDATA SCLK 15 5 AUX GND RY1603 10 AUX-SEL RELAY DRIVE Q1601 R-CH 2 L/R FSYNC 16 (Page 91) 16 (Page 89) 17 (Page 92) 3 1 IC416, 417 BCK, LRCK, EMPHASIS SELECT 13 ISOLATION RELAY DRIVE Q1602 15 4 AD-SEL RY1601 CONTROLLER S-RAM DPD A/D CONVERTER IC1607 CLK 19 A/D CONVERTER CIRCUIT GND –2 TUNER GND (Page 89) 6 14 2 R-CH 14 DAC JK2012 R (Page 89) 10 APD ANALOG IN AUX AUDIO BUFFER IC1602 3 BUFFER IC1604 LRCK, BCK 13 8 R-CH –1 BCK 11 12 DE-EMPHASIS 4 (Page 84) DATA DATA LRCK CN12 (1/2) IC416 11 12 13 CLOCK SHIFT IC1606 RY1602 9 8 10 DIGITAL AUDIO INTERFACE RECEIVER IC502 5 6 4 TIMING SDATA BI-PHASE DECODER & FRAME SYNC CONFIDENCE FLAG DEMULTIPLEXER AUDIO SERIAL OUTPUT 26 2 1 12 FSYNC 3 5 11 IC503 (2/2) 1 ERROR ENCODER CRC CHECK CHANNEL STATUS LATCH ERF 25 EMP 3 DITHER 15 1 2 3 4 5 6 7 QA QB QC QD QE QF QG QH MULTIPLEXER 7 CD-ON REGISTER PARITY CHECK 3 IC503 (1/2) SCK AD-ON CD-ON CLOCK & DATA RECOVERY DIR-ON 9 RXP DIR-ON AD-ON AUX-SEL ISOLATION AD-SEL OPTICAL RECEIVER CN14 DIGITAL IN AUX AUDIO MCK 19 13 G DATA 14 CLOCK (256FS) SELECT IC1401 CLK 11 CE 12 INPUT SELECTOR IC415 DATA, CLK DATA, CLK 6 IC1403 11 (2/4) IC1403 (3/4) (Page 86) 10 SYNC (44.1kHz) BUFFER IC701 (2/2) ISOLATION IC703 (2/2) COUNTER IC1402 2 EEPROM IC302 3 1 8 9 IC1403 (4/4) 10 – 87 – PW-ON DIR-SEL 05 18 19 20 (Page 91) (Page 94) (Page 94) DATA 12 CLK 13 6 5 79 7 EE-CKO OSC IC1403 (1/4) DIR-ERR X1401 11.2896MHz 6 3 5 2 3 4 8 80 EMP-IN 4 SP-CE BUFFER IC413 (1/3) S-CKO 5 S-OUT LEVEL SHIFT IC1010 (1/2) 256FS 7-8. 4 1 • Signal path. MASTER CONTROLLER IC301 (1/4) : CD PLAY : FM/AM : AUX DIGITAL AUDIO – 88 – XES-Z50 BLOCK DIAGRAM – CHANGER UNIT (MAIN Section (2/2)) – LRCK, BCK (Page 88) S2OUT 88 38 SIB BCK LRCK 14 DIN 16 SCK CLK (Page 88) DATA (SUB WOOFER) CRDY 2 CD0 – CD7 7 – 10, 12 – 15 18 3 5 4 32 CAS RAS OE WE DATA 35 BCK 34 LRCK DATA (MID REAR) LEVEL SHIFT IC105 (1/2) SOB 40 MA00 – MA08 23 82, 83, 85, 86, 88, 89, 92, 93, 95 50, 52 – 54, 56 – 59, 62 – 65, 67 – 70 18 – 21, 24 – 28 2 – 5, 7 – 10, 35 – 38, 40 – 43 30 31 16 29 15 A0 – A8 I/O1 – I/O16 UCAS LCAS RAS OE WE 94 BCK 95 LRCK DATA, CLK DIGITAL SIGNAL PROCESSOR (FOR HIGH FRONT, MID REAR SPEAKER) IC101 XTI LRCK, BCK DATA (HIGH FRONT) SOA 39 LEVEL SHIFT IC603 S3OUT 87 (Page 88) 16 37 SIA XCRD XCWR RESET DATA S1OUT 89 MD00 – MD15 • Signal path. 103 72 100 99 : CD PLAY RD WR RST 14 93 S1DI CD 92 S2DI DIR 91 S3DI AD CCS CCNT 13 D8 – D15 +5V 9 MCK1 (768FS) 10 MCK2 (384FS) IC103 (2/3) IC602 (2/2) DIGITAL SIGNAL PROCESSOR IC601 6 D-RAM IC102 X101 40.0MHz IC103 (3/3) BUSY DOUT CE RESET 23 DATA BUS 37 SIA 38 SIB 35 BCK 34 LRCK 7 – 10, 12 – 15 18 3 MA00 – MA08 5 4 32 82, 83, 85, 86, 88, 89, 92, 93, 95 50, 52 – 54, 56 – 59, 62 – 65, 67 – 70 18 – 21, 24 – 28 2 – 5, 7 – 10, 35 – 38, 40 – 43 30 31 16 29 15 A0 – A8 I/O1 – I/O16 UCAS LCAS RAS OE WE CD0 – CD7 XCRD XCWR RESET D8 – D15 D8 – D15 RD A0 (Page 91) 1 IC411 (1/3) 3 5 A1 LEVEL SHIFT IC418 (1/2) IC412 (1/2) 103 72 100 99 A0 – A19 A20 D0 – D7 30 – 27, 22 – 15, 10 – 3 46 31 – 34, 38 – 40 A1 – A20 ADDRESS BUS OE 43 CE 11 WE 44 FLASH MEMORY IC402 43 OE 11 CE 44 WE A0 – A19 A20 D0 – D7 30 – 27, 22 – 15, 10 – 3 46 31 – 34, 38 – 40 DATA BUS DATA BUS RD HWR 10 RST 70 71 5 72 90 89 FROM-CE1 FROM-CE2 18 – 21, 23 – 34 D0 – D15 LWR A0 – A20 CE 13 IC412 (2/2) RD HWR DSPRST 36 – 43, 45 – 56, 100 8 9 LWR D0 – D15 ADDRESS BUS A0 – A20 ADDRESS BUS 88 12 IC414 (1/5) 9 MASTER CONTROLLER IC301 (2/4) 05 – 89 – 11 13 D-RAM IC202 FLASH MEMORY IC401 BUSY DATA CE 82 85 6 MD00 – MD15 LEVEL SHIFT IC418 (2/2) IC411 (2/3) A20 DATA BUS 6 4 12 RD WR RST 2 2711-CE 21 XRST LEVEL SHIFT IC105 (2/2) RD WR RST D8 – D15 SOB 40 CRDY 2 CCS CCNT LEVEL SHIFT IC304 CE T/R SOA 39 DIGITAL SIGNAL PROCESSOR (FOR SUB WOOFER) IC201 DSP-RDY CE RST 7 D8 – D15 19 18 17 20 1 OSC IC103 (1/3) XTI BUSY DATA 2 A1 – A20 X601 18.43MHz CAS RAS OE WE 2 LWR CE RD HWR 6 D0 – D7 OSC IC602 (1/2) DSP-BUSY DSP-SI 2710-CE 7-9. – 90 – 22 (Page 91) XES-Z50 7-10. BLOCK DIAGRAM – CHANGER UNIT (D/A CONVERTER Section) – DIGITAL FILTER IC1101 BCK LRCK 28 LRCI OUTPUT DATA INTERFACE TIMING CONTROL DOR 23 BCKO 26 WCKO 25 2 7 DATA ELECTRICAL VOLUME IC1106 I OUT BCKI 1 24 14 I-V AMP IC1104 (1/2) JK3011 LOW-PASS FILTER IC1104 (2/2) 16 AINL AOUTL MUX 16 16 CLOCK L. E. R-CH (IC1203) JK3021 LINE AMP IC1207 AOUTL 14 MUTE DEMP 15 16 AINL CS MUTE 21 LOW-PASS FILTER IC1204 (2/2) SCK XDITHER 14 2 7 I-V AMP IC1204 (1/2) 3 6 2 8 L R-CH JK3022 R RY1201 CLK RSTN 6 28 LRCI I OUT 14 BCKO 26 WCKO 25 ELECTRICAL VOLUME IC1206 (SAME AS IC1106.) DATA DOR 23 XTI 2 BCKI 1 LINE OUT MID (3WAY) REAR (4CH) SDI DOL 24 DIGITAL FILTER IC1201 (SAME AS IC1101.) CE0 DATA 1 DI 8 CLK D/A CONVERTER IC1202 (SAME AS IC1102.) 2 6 DATA 3 CS DEMP MUTE 15 R-CH SERIAL/PARALLEL REGISTER SCK 21 RY1101 CONTROL REGISTER SDI 14 XDITHER RSTN XTI 6 L JK3012 R R-CH R-CH SYSTEM CLOCK LINE AMP IC1107 14 R-CH R-CH (IC1103) MUTE/ATTENUATE/ DE-EMPHASIS CONTROL CIRCUIT LINE OUT HIGH (3WAY) FRONT (4CH) MUTE BCK LRCK 2 LEVEL SHIFT IC1010 DOL FILTER/ ATTENUATOR PROCESS CIRCUIT INPUT DATA INTERFACE D/A CONVERTER DATA (SUB WOOFER) DI CLOCK 1 DATA (MID REAR) INPUT INTERFACE 22 L. E. (Page 90) DATA (HIGH FRONT) D/A CONVERTER IC1102 R-CH CE1 D/A CONVERTER IC1302 (SAME AS IC1102.) DEMP 6 2 8 R-CH RY1301 R-CH CE2 05 CE1 CE2 DITHER 60 97 98 99 MASTER CONTROLLER IC301 (3/4) 11 MUTE SWITCH IC413 (2/3) VOLCE2 15 3 L JK3032 R XRST CE0 (Page 88) 17 VOLCE1 21 (Page 88) DATA, CLK VOLCE0 (Page 89) R-CH (IC1303) EMP-O 18 CLOCK L. E. JK3031 LINE AMP IC1307 AOUTL 14 MUTE MUTE 16 256FS 16 AINL CS XDITHER 15 2 7 LOW-PASS FILTER IC1304 (2/2) SCK RSTN 21 BCKO 26 WCKO 25 I-V AMP IC1304 (1/2) CLK XTI 14 I OUT 14 LINE OUT SUB WOOFER ELECTRICAL VOLUME IC1306 (SAME AS IC1106.) DATA DOR 23 6 28 LRCI 1 SDI DIGITAL FILTER IC1301 (SAME AS IC1101.) 2 BCKI SMUTE 59 13 IC411 (3/3) 9 10 12 5 6 8 IC414 (2/5) RELAY DRIVE Q1001 MUTE 58 PW ON (Page 87) DOL 24 DATA 1 DI 23 (Page 94) – 91 – – 92 – • Signal path. : CD PLAY XES-Z50 7-11. BLOCK DIAGRAM – CHANGER UNIT (BUS CONTROL/POWER SUPPLY Section) – CN13 SONY BUS CONTROL B+ 7 CN11 +18V +15V BUS ON SCHMITT TRIGGER IC305 (1/2) RESET SIGNAL GENERATOR IC303 +5V D804 6 2 7 RESET RSTI RESET SWITCH 6 DATA 8 DATAO SIRCS 4 4 3 2 CLKI BIN CLKO SWITCH LOFF 12 SWITCH 15 UNISI 9 13 UNISO 11 17 UNICKI BUSON 13 BOUT SIRCS BUS ON 3 12 BUS DATA 5 6 LOF SWITCH DATA 1 BUSON OUT SI SO BUS CLK TO CONTROL UNIT RESET SYSTEM CONTROLLER AV. REF 4 4 11 7 CLK SCK RST RESET SWITCH RSTO 10 SO 9 +3.3V REGULATOR IC803 67 EX-IN SCK 11 +5V OPTICAL RECEIVER CIRCUIT B+ 8 REMOTE SWITCH Q871, 872 B+ SWITCH Q904, 905 +5V (UC5V) B+ SWITCH Q502, 503 +5V REGULATOR IC802 REGULATOR IC804 +9V (RELAY B+) +9V REGULATOR IC801 REGULATOR Q802 B+ SWITCH Q803, 804 IC414 (4/5) DIR-SEL 4 BUS INTERFACE (FOR SONY BUS) IC951 D902 +5V REGULATOR IC904 +5V (D15V) +3.3V GND +5V REGULATOR IC902 +5V (SERVO CIRCUIT) X301 14.74MHz 3 L803 (2/2) +5V REGULATOR IC901 +5V CLOCK GENERATOR (IC503) 66 X-IN SI L802 B+ SWITCH Q303, 304 +5V (RF CIRCUIT) BUSON +12V B+ SWITCH Q903 BATTERY CHECK Q901, 902 93 LINK OFF1 9 2 L803 (1/2) +5V DIGITAL CIRCUIT BUS ON SWITCH Q393 F1 REM OUT +9V REGULATOR IC905 7 95 LINK OFF2 L801 –8V +9V MOTOR SERVO CIRCUIT BUS ON SWITCH Q392 1 DC/DC CONVERTER UNIT 1 87 BUS ON CN12 (2/2) MASTER BUS CONTROLLER +5V/–5V REGULATOR IC1503, 1504 1 BU-IN 84 10 DATAI BUS CLK +5V IC305 (2/2) RSTO –18V +8V –5V BU-IN 64 5 BUS DATA +15V/–15V REGULATOR IC1501, 1502 –15V BATTERY CHECK Q801 MASTER CONTROLLER IC301 (4/4) BUS INTERFACE (FOR SONY BUS) IC306 A/D, D/A CONVERTER CIRCUIT 63 SYSRST POWER 3 PW ON 1 2 IC414 (3/5) B+ 7 1 14 S-IN (RX) 10 1 LED ELVON 12 BUFFER IC413 (3/3) 12 S-OUT (TX) BATTERY CHECK DSP-DATA PW ON 6 11 +5V 55 EJTKEY 12 11 (Page 86) (Page 86) SYSTEM CONTROLLER IC301 (3/3) D301 60 WUP BUSON RST 05 – 93 – (Page 88) 20 (Page 88) 23 (Page 92) IC414 (5/5) PW-ON 2 SW11 LCD-DATA 19 SI SO SCK 54 52 53 51 BUSON SI SO SCK – 94 – XES-Z50 • Circuit Boards Location – CHANGER UNIT – – CONTROL UNIT – LINE OUT board DAC board TRANSLATION board DPT board OPEN/CLOSE 1 board OPEN/CLOSE 2 board DISPLAY board LINE IN board DSP board SW board FM/AM TUNER assy CHANGER board LIQUID CRYSTAL MODULE MAIN board EJT board DOE board SENSOR board DRIVER board – CONNECTOR BOX & DISPLAY HOLDER SECTION – TRANSLATION (CONNECTOR) board TRANSLATION (HIDE) board – 95 – – 96 – • Waveforms – CONTROL UNIT (MAIN Board) – 6 IC501 &™ (XT2) 1 IC802 ^§ (EXTAL) 2.2 Vp-p 3.2 Vp-p 31 µs 68 ns 2 IC802 ^¶ (XTAL) 7 IC501 &º (X1) 3.1 Vp-p 3.4 Vp-p 68 ns 198 ns 3 IC502 8 (X1) 8 IC501 ^ª (X2) 2.8 Vp-p 124 ns 5.1 Vp-p 198 ns 4 IC502 9 (X2) 9 IC501 %£ (FG) (Front panel is being removed or attached.) 6.5 Vp-p 5.8 Vp-p 124 ns 5 IC501 &£ (XT1) Approx. 100 ms 2.3 Vp-p 31 µs – 150 – – CONTROL UNIT (DISPLAY Section) – 1 PH21 COLLECTOR (Front panel is being removed or attached.) – CHANGER UNIT (DRIVER Board) – 1 IC101 !¢ (TE) 5.3 Vp-p Approx. 920 mVp-p Approx. 100 ms 2 IC101 !§ (FE) 2 IC901 ^§ (EXTAL) Approx. 520 mVp-p 3.1 Vp-p 68 ns 3 IC101 !¶ (RFO) 3 IC901 ^¶ (XTAL) 1.1 3.8 Vp-p +0.3 –0.2 Vp-p 68 ns 4 IC252 8 5.3 Vp-p 3.8 µs 5 IC251 2, IC252 9 5.2 Vp-p 3.8 µs – 151 – – CHANGER UNIT (CHANGER Board) – 6 IC251 4, 6 6 IC501 @¢ (RF) 1 IC601 3 (RF) 2.6 Vp-p Approx. 1.1 Vp-p +0.3 1.1 –0.2 Vp-p 3.8 µs 2 IC601 4 (TE) 7 IC401 !£ (WDCI), IC501 #¡ (WDCK) Note: DRIVER board waveforms are CD play mode. 5.4 Vp-p Approx. 920 mVp-p 11.3 µs 3 IC601 7 (FE) 8 IC401 @∞ (LRCK), IC501 #™ (LRCK) Approx. 520 mVp-p 5.4 Vp-p 22.7 µs 4 IC601 !∞ (XTAL) 9 IC401 @£ (BCK), IC501 #∞ (BCK) 5.3 Vp-p 4.8 Vp-p 89 ns 474 ns 5 IC501 4 (MDP) 0 IC401 7 (RFCK), IC501 $£ (RFCK) 2.6 Vp-p 5.2 Vp-p 3.8 µs – 152 – 136 µs !¡ IC401 3 (WFCK), IC501 ^™ (WFCK) !§ IC501 %• (C16M) 4.7 Vp-p 5.2 Vp-p 136 µs @¡ IC303 @ª (EXTAL) 59 ns 99 ns @™ IC303 #º (XTAL) !¶ IC503 0 (CKO) !™ IC501 %¢ (XTAO) 4.3 Vp-p 59 ns 4.1 Vp-p 5.4 Vp-p 99 ns 236 ns !£ IC501 %£ (XTAI) 3.1 Vp-p !• IC503 1 (REF) Note: CHANGER board waveforms are CD play mode. 5.4 Vp-p 2.5 Vp-p 22.7 µs 59 ns !¢ IC401 !§ (XTAI) !ª IC301 #¡ (XTLI) 4.6 Vp-p 59 ns 3.1 Vp-p 125 ns !∞ IC401 5 (C4M) @º IC301 #™ (XTLO) 5.2 Vp-p 236 ns 4.5 Vp-p 125 ns – 153 – – CHANGER UNIT (DSP Board) – 1 IC701 !™ (BCK IN) !¡ IC601 (∞ (LRCK) 6 IC703 !¢ (SYNC) NOTE 1 5.1 Vp-p 5.2 Vp-p 22.7 µs 474 ns 2 IC701 3 (SYNC OUT) NOTE 1 7 IC502 !¡ (FSYNC) 5.3 Vp-p CD PLAY, FM/AM, AUX ANALOG AUDIO MODE: 22.7 µs AUX DIGITAL AUDIO MODE: 90.8 µs NOTE 2 !™ IC601 0 (MCK2 (384FS)) 5.4 Vp-p 5.1 Vp-p 2.6 Vp-p 22.7 µs 90.8 µs 8 IC502 !™ (SCK) 3 IC701 5 (LRCK IN) NOTE 1 NOTE 2 55 ns !£ IC301 ^¶ (EX-IN) 5.1 Vp-p 5.5 Vp-p 3 Vp-p 1.42 µs 22.7 µs 4 IC702 !∞ (LRCK) 9 IC502 !ª (MCK) NOTE 1 68 ns NOTE 2 !¢ IC301 ^§ (X-IN) 5 Vp-p 5.2 Vp-p 2 Vp-p 22.7 µs 5 IC702 !¢ (BCK) 358 ns NOTE 1 68 ns 0 IC601 (¢ (BCK) !∞ IC101, 201 @£ (XTI) 5.2 Vp-p 5.1 Vp-p 1.3 Vp-p 474 ns CD PLAY MODE: 474 ns FM/AM, AUX ANALOG AUDIO MODE: 354 ns AUX DIGITAL AUDIO MODE: 1.42 µs – 154 – 30 ns – CHANGER UNIT (DAC Board) – !§ IC101, 201 #¢ (LRCK) 5 IC1101, 1201, 1301 6 (XTI) NOTE 2 1 IC1010 2 (MCK IN) NOTE 1 5 Vp-p 3.5 Vp-p CD PLAY, FM/AM, AUX ANALOG AUDIO MODE: 22.7 µs AUX DIGITAL AUDIO MODE: 90.8 µs 6 Vp-p 89 ns 358 ns 6 IC1101, 1201, 1301 6 (XTI) NOTE 1 2 IC1010 7 (BCK IN) !¶ IC101, 201 #∞ (BCK) 6.6 Vp-p 5.2 Vp-p 3.4 Vp-p CD PLAY MODE: 474 ns FM/AM, AUX ANALOG AUDIO MODE: 354 ns AUX DIGITAL AUDIO MODE: 1.42 µs CD PLAY MODE: 474 ns FM/AM, AUX ANALOG AUDIO MODE: 354 ns AUX DIGITAL AUDIO MODE: 1.42 µs 354 ns 7 IC1101, 1201, 1301 @• (LRCI) 3 IC1010 9 (LRCK IN) Notes: 1. CD play mode 2. AUX DIGITAL AUDIO mode. 5.3 Vp-p 5.4 Vp-p CD PLAY, FM/AM, AUX ANALOG AUDIO MODE: 22.7 µs AUX DIGITAL AUDIO MODE: 90.8 µs CD PLAY, FM/AM, AUX ANALOG AUDIO MODE: 22.7 µs AUX DIGITAL AUDIO MODE: 90.8 µs 8 IC1101, 1201, 1301 @§ (BCKO) NOTE 2 4 IC1101, 1201, 1301 2 (BCKI) 4.9 Vp-p 5.3 Vp-p 89 ns CD PLAY MODE: 474 ns FM/AM, AUX ANALOG AUDIO MODE: 354 ns AUX DIGITAL AUDIO MODE: 1.42 µs – 155 – 9 IC1101, 1201, 1301 @§ (BCKO) NOTE 1 !£ IC1401 2 (1A) !• IC1402 6 (1QD) 5.2 Vp-p 354 ns 5.1 Vp-p 1.42 µs 89 ns 0 IC1101, 1201, 1301 @∞ (WCKO) !¢ IC1401 5 (2A) !¡ IC1607 @º (OCLK) !ª IC1402 8 (2QD) NOTE 1 5.2 Vp-p 5.2 Vp-p CD PLAY, FM/AM, AUX ANALOG AUDIO MODE: 2.84 µs AUX DIGITAL AUDIO MODE: 11.3 µs 5.2 Vp-p 354 ns 5.3 Vp-p 22.7 µs !∞ IC1401 3 (1Y), 6 (2Y) NOTE 2 @º IC1606 5 (Q) NOTE 3 NOTE 3 5.3 Vp-p 3.8 Vp-p 5.3 Vp-p 22.7 µs 89 ns !§ IC1401 3 (1Y), 6 (2Y) NOTE 1 @¡ IC1607 !¢ (SCLK) NOTE 3 177 ns !™ IC1403 4 5.4 Vp-p 5.2 Vp-p 4.8 Vp-p 354 ns 354 ns 89 ns !¶ IC1402 1 (1CK) @™ IC1607 !£ (L/R) 5.1 Vp-p 5.3 Vp-p 22.7 µs 89 ns – 156 – NOTE 3 @£ IC1607 !§ (FSYNC) NOTE 3 5.3 Vp-p 11.35 µs @¢ IC1607 !ª (CLK) NOTE 2 6 Vp-p 89 ns @∞ IC1607 !ª (CLK) NOTE 1 6.5 Vp-p 354 ns Notes: 1. AUX DIGITAL AUDIO mode. 2. CD PLAY, FM/AM, and AUX ANALOG AUDIO mode. 3. FM/AM and AUX ANALOG AUDIO mode. – 157 – • IC Block Diagram – MAIN Board – MM1175XF-T1 BUS ON 1 OUT 14 VCC RESET 2 OUT RESET SWITCH 13 RESET IN BATT 3 BATT SWITCH 12 BUS ON IN CLK 4 OUT 11 CLK IN VREF 5 10 BATT CHECK DATA 6 IN/OUT 9 DATA IN GND 7 IC515 8 DATA OUT IC516 NM24C04EM8-FL63 START CYCLE START/ STOP LOGIC CONTROL LOGIC X DECODER START STOP LOGIC 6 32 32 x 16 x 8 4 H.V. PUMP/TIMING 8 VCC LOAD DEVICE ADDRESS COMPARATOR 16 WORD ADDRESS COUNTER A0 1 A1 2 A2 3 R/W COMP DATA RECOVERY DATA WORD ADDR/COUNTER Y DEC Y DECODER R/W 6 SDL E2PROM 5 SDA DOUT CK D IN D OUT DATA REGISTER D OUT ACK SDA 5 – 158 – SERIAL MUX DOUT/ACK LOGIC DIN 8 7 TST LOAD INC GND 4 4 4 VSS SERIAL EN CONTROL LOGIC EEPROM INC A0 1 A1 2 A2 3 VCC 8 NC 7 SCL LOAD SLAVE ADDRESS REGISTER & COMPARATOR H.V. GENERATION TIMING & CONTROL AT24C08N-10SI-SL383B X DEC IC503 IC804 1 2 3 4 5 6 7 8 A15 A14 A13 A12 A11 A10 A9 A8 MBM29F400BA-70PFTN-MA02 A16 48 BYTE 47 4,194,304 CELL MATRIX X DECODER Y GATE ADDRESS LATCH 9 NC 10 NC I/O BUFFER Y DECODER DATA LATCH STB GND 46 DQ15/A–1 45 DQ7 44 DQ14 43 DQ6 42 DQ13 41 DQ5 40 DQ12 39 DQ4 38 VCC 37 STB 11 12 WE IC805 6 WRITE/ERASE PULSE TIMER 12 RY/BY BUFFER 17 ERASE CIRCUIT 28 GND 27 CE 26 A0 25 CXK516100TM-70LL-TL LEVEL SHIFT & BUFFER CE VCC MEMORY MATRIX GND I/O BUFFER I/O GATE COLUMN DECODER A5 44 A6 43 A7 42 OE 41 UB 40 LB 39 CONTROL I/O16 38 I/O15 37 I/O14 36 I/O13 35 ROW DECODER 512 x 1024 WE OE CHIP ENABLE/ OUTPUT ENABLE CIRCUIT A4 A3 A2 A1 A0 I/O5 13 I/O6 14 I/O7 15 I/O8 16 36 35 34 33 32 31 30 29 WRITE CIRCUIT I/O1 7 I/O2 8 I/O3 9 I/O4 10 11 LOW VCC DETECTOR CIRCUIT RESET 13 NC 14 NC RY/BY 15 16 NC A17 17 A7 18 A6 19 A5 20 A4 21 A3 22 A2 23 A1 24 1 2 3 4 5 CONTROL CIRCUIT DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 GND MEMORY MATRIX VCC 512 x 1024 PRE DECODER I/O GATE COLUMN DECODER I/O BUFFER A15 18 A14 19 A13 20 A12 21 34 33 I/O12 32 I/O11 31 I/O10 30 I/O9 29 NC 28 A8 27 A9 26 A10 25 A11 24 NC 23 LEVEL SHIFT & BUFFER 22 NC – 159 – – DISPLAY Board – FEED BACK VCC OUT TL5001CD INPUT IC801 4 3 2 1 U.V.L.O DEAD-TIME COMPARATOR REFERENCE VOLTAGE + – ERROR AMP – + OSC + – S.C.P. COMPARATOR 1 SWITCH 'ON' AT 'H' – + PWM COMPARATOR – + S.C.P. LATCH IC931 1 2 3 4 5 6 7 8 A15 A14 A13 A12 A11 A10 A9 A8 6 7 8 RT GND SCP 5 DEAD-TIME CONTROL S.C.P. COMPARATOR 2 MBM29F800-DISPU A16 48 BYTE 47 X DECODER 8,388,608 CELL MATRIX Y GATE ADDRESS LATCH 9 NC 10 NC Y DECODER I/O BUFFER DATA LATCH STB GND 46 DQ15/A–1 45 DQ7 44 DQ14 43 DQ6 42 DQ13 41 DQ5 40 DQ12 39 DQ4 38 VCC 37 STB 11 12 WE CONTROL CIRCUIT LOW VCC DETECTOR CIRCUIT RESET 13 NC 14 NC RY/BY 15 A18 16 A17 17 A7 18 A6 19 A5 20 A4 21 A3 22 A2 23 A1 24 WRITE/ERASE PULSE TIMER DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 36 35 34 33 32 31 30 29 WRITE CIRCUIT RY/BY BUFFER ERASE CIRCUIT CHIP ENABLE/ OUTPUT ENABLE CIRCUIT OE 28 GND 27 CE 26 A0 25 – 160 – IC932 CXK516100TM-70LL-TL A4 A3 A2 A1 A0 1 2 3 4 5 LEVEL SHIFT & BUFFER CE 6 I/O1 7 I/O2 8 I/O3 9 I/O4 10 11 12 VCC MEMORY MATRIX GND 17 CONTROL I/O16 38 I/O15 37 I/O14 36 I/O13 35 ROW DECODER 512 x 1024 I/O5 13 I/O6 14 I/O7 15 I/O8 16 I/O GATE COLUMN DECODER I/O BUFFER WE A5 44 A6 43 A7 42 OE 41 UB 40 LB 39 GND MEMORY MATRIX VCC 512 x 1024 PRE DECODER I/O GATE COLUMN DECODER I/O BUFFER A15 18 A14 19 34 33 I/O12 32 I/O11 31 I/O10 30 I/O9 29 NC 28 A13 20 A12 21 A8 27 A9 26 A10 25 A11 24 NC 23 LEVEL SHIFT & BUFFER 22 NC – OPEN/CLOSE 2 Board – IC11 TA7291P DRIVER CIRCUIT REGULATOR DRIVER CIRCUIT 1 2 3 4 5 6 7 8 9 10 GND OUT1 NC VREF IN1 IN2 VCC VS NC OUT2 PROTECT CIRCUIT – 161 – – DRIVER Board – CXA1791M-T6 IC201 LD 1 OUT3 1 2 3 4 IN1 5 VC APC PD AMP + – PD 2 APC LD AMP + – VREF 1.25V 20 VCC VCC 18 RFI VC – + VC RF IV AMP1 VC – + RF SUMMING AMP IN3 8 VCC1 9 10 11 12 13 17 RFO VC PD2 4 – + VC DRIVER IN2 6 GND 7 19 APC ON PD1 3 BA6247FP-Y CONTROL IC101 – + RF IV AMP2 DRIVER 16 FE FOCUS ERROR AMP GND 5 15 FE BIAS VC VC F 6 – + VC F IV AMP – + VC 14 TE TRACKING ERROR AMP 13 EI E 7 – + VC 12 EO VCC E IV AMP VC BUFFER – + VR 8 VC 9 VC NC 10 11 NC GND SPDL– SPDL+ OUT MDP VCC VCC TRF TRR OUT TR– TR+ MUTE BA6297AFP 28 27 26 25 24 23 22 21 20 19 18 17 16 15 – + + – – + + – T.S.D MUTE + – + – + – + – 1 2 3 4 5 6 7 8 9 10 11 12 13 14 OUT SLR SLF VREFIN VREF GND FF FR OUT F– F+ GND + – SL+ SL– IC202 – 162 – DRIVER 25 24 23 22 OUT2 21 20 GND 19 GND 18 OUT1 17 16 VCC2 15 14 VR – CHANGER Board – INC DATA RECOVERY X DECODER 9 10 11 12 13 14 15 XTAI (BC) (TCK) (TDI) (TENAI) (TDO) VST BCK DATA 16 17 18 19 20 21 22 23 24 D OUT 5 SDA CXK581000AM-10LL A6 A5 A4 A3 A2 A1 A0 6 7 8 9 10 11 12 I/O1 I/O2 I/O3 GND 13 14 15 16 MEMORY MATRIX 1024X1024 1 2 3 4 5 31 A15 30 CE2 29 WE 28 27 26 25 A13 A8 A9 A11 24 OE LEVEL SHIFT LEVEL SHIFT BUFFER BUFFER I/O GATE COLUMN DECODER NC A16 A14 A12 A7 BUFFER ROW DECODER 32 VCC LEVEL SHIFT MWE MRE QRCK QTBC XQOK VDD VSS AM17 AM18 AM19 AM20 AM21 XWIH XEMP 74 73 72 71 70 69 68 67 66 65 SUBQ TBC CONTROL CPU I/F DATA LINKING CONTROL 4K BIT RAM I/O BUFFER 64 63 62 61 60 59 58 57 SDTO XSOE SCK SDTI EXPXLT XRDE XWRE SPSL 56 OSCE D OUT/ ACK LOGIC D IN IC304 BCKI DATI LRCI VSS WDCI TEST XTAO 78 77 76 75 SERIAL MUX Y DECODER VSS 4 EEPROM 1 2 3 4 5 6 7 8 79 23 A10 22 CE1 21 20 19 18 17 I/O8 I/O7 I/O6 I/O5 I/O4 – 163 – ADDRESS MONITOR DSP I/F VWA TIMING GEN. SELECTOR WRITE BASE COUNTER READ BASE COUNTER DAC I/F DIGITAL OUT DRAM I/F 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 A3 A2 A1 A0 A9 VSS VDO A10 A11 XRAS XWE XOE2 XOE3 XOE4 DATA WORD ADDRESS/ COUNTER GRSRST XRST WFCK DIN C4M XROI RFCK GTOP 80 DOUT LOAD R/W H.V. PUMP/ TIMING EN SERIAL LOAD CONTROL DEVICE COMP ADDRESS LOGIC COMPARATOR GRSCOR 8 VCC 7 WP 6 SCL START/ STOP LOGIC A0 1 A1 2 A2 3 CXD2512AQ SCOR IC401 AT24C32N-10SI-TR LRCK IC302 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 A4 A5 A6 VSS A7 A8 XWE4 XWE3 XWE2 XOE XCAS D3 D4 D1 D2 IC402, 403 µPD424400GS-60-9JD CLOCK OSC D1 1 26 GND D2 2 25 D4 A0–A9 XRAS 4 24 D3 INPUT BUFFER XWE 3 COLUMN DECODER 23 XCAS A9 5 22 XOE NC 6 NC 7 NC 8 SENSE REFRESH AMP INPUT/OUTPUT CONTROL SWITCH A3 12 18 A8 OUTPUT BUFFER ROW DECODER A2 11 A0–A9 A1 10 ADDRESS BUFFER A0 9 21 NC 20 NC 19 NC 17 A7 MEMORY CELL 16 A6 15 A5 VDD 13 EXCK 65 SCOR WFCK EMPH DOUT MD2 C16M FSOF FSTT XTSL XTAO XTAI VSS APTL APTR MNT0 MNT1 MNT2 MNT3 XRAOF C2PO RFCK GFS XPLCK CXD2540Q SBSO IC501 14 A4 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 SUBCODE P-W PROCESSOR DIGITAL OUT CLOCK GENERATOR TIMING GENERATOR 2 SERIAL/PARALLEL PROCESSOR TIMING GENERATOR 1 68 69 70 71 72 73 74 75 76 DATO 77 XLTO 78 CLKO 79 D/A DATA PROCESSOR PRIORITY ENCODER ADDRESS GENERATOR CPU INTERFACE RESISTER 32K RAM ERROR CORRECTOR EFM DEMODULATOR SERVO AUTO SEQUENCER MIRR 80 SYNC PROTECTOR NOISE SHAPER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 RF OSC FSW MON MDP MDS LOCK NC VCOO VCOI TEST PDO VSS PWMI CLV PROCESSOR FOK 18-TIMES EVER SAMPLING FILTER – 164 – XUGF DYOP 64LRCK 64BCLK 64DATA BCLK DATA VDD LRCK WDCK PSSL NC ASYE 27 ASYO MIX DIGITAL PLL VARI-PITCH DOUBLE SPEED VPCO VCKI FILO FILI PCO AVSS CLTV AVDD MUTE SENS XRST DATA XLAT VDD CLOCK SEIN CNIN SUBCODE Q PROCESSOR V16M VCTL SQSO 66 SQCK 67 40 39 38 37 36 35 34 33 32 31 30 29 28 PEAK DETECTOR ASYMMETRY CORRECTION 26 ASYI 25 BIAS IC502 SN74HC74ANS 14 13 12 11 VCC 10 IC951 9 8 PR Q Q D CK BUS ON OUT 1 SW 14 VCC BUS ON INPUT 2 SW 13 BUS ON CLR PR D GND 3 12 LINK OFF BUS CLK 4 11 CLK OUT Q VREF 5 Q CK MM1284XFFE CLR 10 DATA OUT BUS DATA 6 GND 4 5 6 7 1 2 3 9 DATA IN RESET SW BUS RESET 7 LOCK S2 S1 M2 M1 CKO VSS TC9246F-TP1 VDD IC503 8 RESET 16 15 14 13 12 11 10 9 – SW Board – IC801 BA6287F OUT1 1 LOCK DETECTION CIRCUIT 8 GND MICRO COMPUTER INTERFACE VAR. PHASE COMPARATOR REF. SELECTOR PROGRAMMABLE COUNTER VCO VM 2 7 OUT2 DRIVER DRIVER 1 2 3 4 5 6 7 8 REF PD VDDA AMPI AMPO VSSA XI XO TSD VCC 3 CONTROL LOGIC 6 VREF POWER SAVE FIN 4 CXD2501Q AVSS NC IGEN AVDD DVDD NC CDS NC SSTP NC FFON FRDR FRON IC601 64 63 62 61 60 59 58 57 56 55 54 53 52 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 MPX A/D CONVERTER DSP NOISE SHAPER AND PWM MODULATOR MIRR/ DFCT/ FOK DETECTOR JUMP/ SEARCH CONTROL µ-COM INTERFACE 51 50 49 48 47 46 45 44 43 FFDR TFON TRDR TRON TFDR NC TEST NC DVSS 42 41 40 39 38 37 36 35 34 33 NC SFON SRDR SRON SFDR NC SOUT XOLT SOCK XRST 20 21 22 23 24 25 26 27 28 29 30 31 32 MIRR CLK NC XLT DATA COUT NC DVDD NC SENS SCLK NC DIRC AD11 AD10 RF TE SE NC FE VC DVSS NC ATSK NC DFSW DFCT XTAL NC XTSL LOCK FOK – 165 – 5 RIN – DSP Board – IC102, 202 HM51W4260CLTT-7 31 30 29 28 27 26 25 24 23 SERIAL LOAD CONTROL DEVICE COMP ADDRESS LOGIC COMPARATOR A0 1 A1 2 A2 3 R/W PERIPHERAL CIRCUIT DATA WORD ADDRESS/ COUNTER DATA RECOVERY X DECODER I/O BUS AND COLUMN DECODER SELECTOR 256K MEMORY ROW ARRAY MAT DECODER D IN VSS 4 I/O BUS D OUT 5 SDA 11 12 13 14 15 16 17 18 19 20 21 22 VCC I/O0 I/O1 I/O2 I/O3 VCC I/O4 I/O5 I/O6 I/O7 NC NC NC NC WE RAS NC A0 A1 A2 A3 IC401 IC402 MM1284XFFE BUS ON OUT 1 SW 14 VCC BUS ON INPUT 2 SW 13 BUS ON GND 3 12 LINK OFF BUS CLK 4 11 CLK OUT VREF 5 10 DATA OUT BUS DATA 6 9 DATA IN RESET SW VCC 2 3 4 5 6 7 8 9 10 BUS RESET 7 D OUT/ ACK LOGIC ADDRESS BUS 1 IC306 EEPROM SERIAL MUX Y DECODER I/O BUFFER H.V. PUMP/ TIMING EN INC I/O BUS AND COLUMN DECODER SELECTOR LOAD 256K MEMORY ROW ARRAY MAT DECODER I/O BUFFER 8 VCC 7 WP 6 SCL START/ STOP LOGIC ADDRESS BUS I/O BUS AT24C32N-10SI-TR VSS LCAS UCAS OE 34 33 32 A8 A7 A6 A5 A4 NC NC NC 44 43 42 41 40 39 38 37 36 35 VSS I/O15 I/O14 I/O13 I/O12 VSS I/O11 I/O10 I/O9 I/O8 IC302 8 RESET MBM29F016-90PFTN-DSP02L MBM29F016-90PFTN-DSP02H NC 48 NC 47 A20 46 NC 45 WE 44 OE 43 RY/BY 42 1 NC 2 NC 3 4 5 6 7 8 9 10 A19 A18 A17 A16 A15 A14 A13 A12 X DECODER 16,777,216 CELL MATRIX Y GATE ADDRESS LATCH Y DECODER I/O BUFFER DATA LATCH STB 11 CE 15 16 17 18 19 20 21 22 A11 A10 A9 A8 A7 A6 A5 A4 CONTROL CIRCUIT LOW VCC DETECTOR CIRCUIT WRITE/ERASE PULSE TIMER WRITE CIRCUIT ERASE CIRCUIT 23 NC 24 NC – 166 – VCC 37 VSS 36 VSS 35 STB 12 VCC 13 NC RESET 14 DQ7 41 DQ6 40 DQ5 39 DQ4 38 CHIP ENABLE/ OUTPUT ENABLE CIRCUIT DQ3 34 DQ2 33 DQ1 32 DQ0 31 A0 30 A1 29 A2 28 A3 27 NC 26 NC 25 LATCH CLOCK SHIFT CLOCK RESET SERIAL DATA OUTPUT 13 12 11 10 9 SQH OUTPUT ENABLE 14 A QA 16 15 VCC SERIAL DATA INPUT TC74VHC595FS (EL) PARALLEL DATA OUTPUT IC415 SHIFT REGISTER QH QF QG QE QC QD QB LATCH GND 1 2 3 4 5 6 7 8 PARALLEL DATA OUTPUT IC502 CS8412-IS-E1 28 VERF 27 CE/F2 C 1 CD/F1 CC/F0 CB/E2 CA/E1 C0/E0 2 3 4 5 6 MULTIPLEXER PARITY CHECK 6 6 3 3 FREQUENCY COMPARATOR ERROR ENCODER CHANNEL STATUS LATCH CRC CHECK VD+ 7 26 SDATA 25 ERF REGISTERS DGND 8 CONFIDENCE FLAG RXP 9 RXN 10 CLOCK AND DATA RECOVERY BI-PHASE DECODER AND FRAME SYNC DEMULTIPLEXER AUDIO SERIAL PORT 24 M1 23 M0 22 21 20 19 18 17 VA+ AGND FILT MCK M2 M3 TIMING FSYNC 11 SCK 12 16 SEL CS12/FCK 13 U 14 15 CBL – 167 – TMOD2 BCKO WCKO DOL DOR VDD TMOD1 SYNCN OW2ON FSEL2 FSEL1 DEMP MUTE SM5843AS1-ET LRCI – DAC Board – IC1101, 1201, 1301 28 27 26 25 24 23 22 21 20 19 18 17 16 15 OUTPUT DATE INTERFACE DE-EMPHASIS CONTROL OP ATTENUATION BLOCK TIMING CONTROL INPUT DATA INTERFACE MUTE/ATTENUATOR CONTROL CLOCK NC 10 CKO IW2N/DIR 13 14 IC1106, 1206, 1306 20 –VCC INPUT INTERFACE AND SINE CONVERTER 3 REFERENCE AND SERVO ZCEN 1 CS 2 SDATAI 3 18 NC 4 17 SERVO DC D.COM 5 16 A.COM BALANCED CURRENT SEGMENT DAC B BIPOLAR OFFSET + – MUX 8 8 VD+ 4 DGND 5 16 AINL 15 AGNDL SCLK 6 SDATAO 7 14 AOUTL CONTROL REGISTER 16 SERIAL PARALLEL REGISTER 13 VA– 12 VA+ 8 8 11 AOUTR MUTE 8 15 A.COM –VDD 6 L.E 7 14 I OUT NC 8 13 NC NC 9 12 BPO DC + – BALANCED CURRENT SEGMENT DAC A CS3310-KP 19 REF DC +VDD NC 10 12 PCM1702U-K-T1 1 2 11 RSTN 9 MLEN 8 MCK 7 MDT 6 VSS CKSLN DATA 5 XTO BCKI IC1102, 1103, 1202 IC1203, 1302, 1303 4 XTI 3 IWIN/DIL 2 INFIN 1 DI/NF2N SYSTEM CLOCK 11 +VCC – 168 – 10 AGNDR MUX 9 AINR Q 7 6 5 S R Q C D Q 1 2 3 4 GND 12 4A CLR 13 4 OE 8 Q 1A 2 PR 14 VCC TC7W74FU D 1 OE 1 IC1606 VCC TC74VHC125F (EL) CK IC1401 1Y 3 11 4Y 2 OE 4 2A 5 10 3 OE 9 3A 2Y 6 GND 7 8 3Y IC1607 AK5390-VS AGND 1 VOLTAGE REFERENCE APD 2 26 AINR+ 25 AINR– AINL+ 3 AINL– 4 ACAL 5 + + – + – LGND 6 + LP FILTER 24 VA– 23 VA+ 12 11 10 QA CLEAR QB 9 8 QC QD + – + DAC 13 DAC TC74VHC393F (EL) NC 8 14 – + – + LP FILTER VL+ 7 IC1402 28 VREF+ 27 VREF– – 22 ICLK 21 NC VCC A 20 OCLK DECIMATION FILTER CLEAR QA QB QC QD 3 4 5 6 A GND 1 2 7 DCAL 9 DPD 10 CMODE 11 SMODE 12 L/R 13 SCLK 14 – 169 – DECIMATION FILTER SERIAL OUTPUT INTERFACE CONTROLLER CALIBRATION SRAM 19 CLK 18 DGND 17 VD+ 16 FSYNC 15 SDATA SECTION 8 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they may have some difference from the original one. • Color Indication of Appearrance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) ↑ ↑ Parts Color Cabinet's Color • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied. • Hardware (# mark) list and accessories are given in the last of the electrical parts list. The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiquens pour la sécurité. Ne les remplacer que par une pièce portant le neméro spécifié. (1) CD CHANGER MAIN SECTION-1 11 20 8 29 10 10 #5 25 9 19 23 20 25 #6 24 22 29 21 15 7 #5 28 6 5 #4 13 26 3 17 not supplied 25 14 4 16 27 #3 #12 7 15 #5 18 #1 #2 12 24 8 2 #2 20 19 #1 1 #5 #6 9 10 10 11 Ref. No. Part No. Description Remark 1 2 3 4 5 X-3373-780-1 3-011-745-01 3-008-192-01 3-008-201-01 3-008-199-01 DOOR ASSY SHAFT (OPEN) PANEL, FRONT SHAFT (BUCKLE) LEVER (BUCKLE) * * * * * 6 * 7 * 8 * 9 10 3-008-193-01 3-008-195-01 3-008-196-01 3-008-216-01 4-924-242-71 BRACKET (BUCKLE) PANEL, SIDE COVER (SIDE PANEL) SPACER (COVER) SCREW (M3X6), FLAT HEAD * * * * * 11 12 * 13 * 14 15 3-008-194-02 3-009-030-01 3-010-364-01 A-3309-787-A 3-931-071-01 COVER (UPPER. LOWER) SEAL (DSP) PANEL, REAR CHANGER BOARD, COMPLETE SCREW (+PTT 2.6X8 CU. C) Ref. No. Part No. Description 16 17 18 19 20 1-664-114-12 3-008-211-01 3-015-121-01 3-008-216-11 3-015-115-01 EJT BOARD BUTTON (EJECT) (6) SHEET (CD FRONT PANEL) SPACER (COVER) SHEET (CD COVER, UPPER. LOWER) 21 22 23 24 25 3-015-114-01 3-008-214-01 3-014-549-01 3-015-120-01 3-014-840-01 SHEET (CD COVER UPPER, BARREL) HEAT SINK (SUB) SHEET (REAR PANEL) SHEET (CD SIDE COVER) SCREW (3X6) (BARREL PLATING), +B 26 27 * 28 29 3-008-215-01 3-011-744-01 3-013-097-01 3-355-210-11 SPRING (BUCKLE OPEN) SPRING (OPEN) SHEET (CHG), INSULATING COVER (2), PIN JACK – 170 – Remark (2) CD CHANGER MAIN SECTION-2 JK3011, 3021, 3031 JK3012, 3022, 3032 61 62 supplied with JK3011, 3021, 3031 63 60 64 59 supplied with JK3021, 3022, 3032 72 58 55 56 57 56 53 54 71 65 56 supplied 66 with JK2012 51 68 56 69 67 supplied 68 with JK2011 52 56 60 JK2012 51 61 F1 70 Ref. No. 59 Part No. Description 51 52 53 54 55 3-906-712-01 3-008-486-01 3-011-971-02 3-008-595-01 A-3309-657-A SCREW (2.6X6) (CU), +PTT CHASSIS (DSP. B) SHEET (B), INSULATING CASE (DSP BOARD), SHIELD DSP BOARD, COMPLETE 56 * 57 58 59 60 3-906-713-01 A-3309-659-A 1-782-287-11 3-912-956-01 3-366-821-01 SCREW (+PTT), GROUND POINT DAC BOARD, COMPLETE CABLE, FLAT (FWCF) (30 CORE) SCREW (2.6X4) (CU), +BVTT BUSHING (RED) 61 62 63 64 65 3-366-821-11 3-008-484-01 1-664-164-12 3-008-483-01 3-008-586-01 BUSHING (WHITE) CHASSIS (DSP. L) LINE OUT BOARD CHASSIS (DSP. MAIN) CHASSIS (INNER) JK2012 1-573-057-31 JACK, PIN 1P (RED) (ANALOG IN AUX AUDIO R) JK3011 1-573-057-21 JACK, PIN 1P (WHITE) (LINE OUT HIGH FRONT L) JK3012 1-573-057-31 JACK, PIN 1P (RED) (LINE OUT HIGH FRONT R) JK3021 1-573-057-21 JACK, PIN 1P (WHITE) (LINE OUT MID REAR L) JK3022 1-573-057-31 JACK, PIN 1P (RED) (LINE OUT MID REAR R) * 66 67 * 68 * 69 3-011-970-01 1-473-994-11 3-366-820-03 1-664-165-12 SHEET (A), INSULATING DC/DC CONVERTER UNIT SHEET (D), INSULATING LINE IN BOARD JK3031 1-573-057-21 JACK, PIN 1P (WHITE) (LINE OUT SUB WOOFER L) JK3032 1-573-057-31 JACK, PIN 1P (RED) (LINE OUT SUB WOOFER R) * * * * * * * * Remark JK2011 Ref. No. Part No. Description * 70 71 72 F1 JK2011 3-008-485-01 1-782-286-11 3-014-160-01 1-532-796-11 1-573-057-21 CHASSIS (DSP. R) CABLE, FLAT (FWCF) (8 CORE) SPACER (POWER) FUSE (BLADE TYPE) (AUTO FUSE) (5A) JACK, PIN 1P (WHITE) (ANALOG IN AUX AUDIO L) – 171 – Remark (3) CD CHANGER MAIN SECTION-3 107 106 104 116 106 #3 112 111 103 #3 111 121 102 125 120 105 108 122 116 110 105 123 101 111 113 111 111 109 #3 115 111 102 117 114 #3 104 106 119 119 125 124 106 118 117 Ref. No. Part No. Description 101 102 * 103 104 105 3-923-342-01 3-375-501-01 3-008-203-01 3-375-504-21 X-3370-157-1 SPRING (FL2), TENSION DAMPER (CNG) COVER (DAMPER L) LEVER (SPRING) ARM (SPRING 2) ASSY * * * * * 106 107 108 109 110 3-912-956-01 3-008-207-01 3-008-209-01 3-008-208-01 3-008-204-01 SCREW (2.6X4) (CU), +BVTT CHASSIS (TOP) CHASSIS (MID) CHASSIS (DOWN) COVER (DAMPER R) * * * * * 111 * 112 * 113 3-013-100-01 SPACER (CHASSIS) 3-013-236-01 SHEET (CHASSIS TOP) 3-014-551-01 SHEET (FLEXIBLE RETAINER) Remark Ref. No. Part No. Description 114 115 116 117 118 3-015-118-01 3-015-116-01 3-014-561-01 3-014-550-01 3-015-119-01 SHEET (CD INNER CHASSIS. REAR S) SHEET (CD INNER CHASSIS. FRONT) SHEET (BLIND) SHEET (LEAD) SHEET (CD INNER CHASSIS. REAR L) * 119 120 * 121 * 122 * 123 3-013-238-02 3-013-615-01 3-013-138-02 3-013-139-02 3-014-492-01 SHEET (CHASSIS DOWN B) SHEET (CHASSIS MID) SHEET (DAMPER L) SHEET (DAMPER R) SHEET (CHASSIS MID 2) * 124 * 125 3-013-237-02 SHEET (CHASSIS DOWN A) 3-014-970-01 SHEET (STOPPER) – 172 – Remark (4) CD CHANGER MAIN SECTION-4 MG-110ES-132 #10 156 163 157 155 KSM-400AAM 154 153 158 not supplied 168 160 159 164 #8 162 164 164 152 166 #9 161 151 167 165 164 Ref. No. Part No. Description * 151 * 152 153 * 154 155 A-3309-668-A 1-664-111-12 1-664-157-11 3-368-567-01 3-388-593-11 * 156 * 157 158 * 159 3-922-950-01 3-928-691-01 3-387-948-01 3-922-150-01 Remark Ref. No. Part No. Description DRIVER BOARD, COMPLETE SW BOARD SWITCH FLEXIBLE BOARD SHEET (MD), INSULATING ESCUTCHEON (2) * 160 161 162 163 164 3-008-217-01 1-664-155-11 1-664-156-11 3-350-124-01 3-015-343-01 BRACKET (FPC) RF FLEXIBLE BOARD DRIVER FLEXIBLE BOARD CUSHION (EJECT) SCREW (2X5) (BARREL PLATING) BRACKET (TR2) CUSHION (EV) SPACER (W) SHEET (EV), INSULATING 165 * 166 * 167 * 168 3-015-342-01 3-013-096-01 3-013-096-11 3-013-096-21 SCREW (2X6) (BARREL PLATING) CUSHION (FLEXIBLE) CUSHION (FLEXIBLE) CUSHION (FLEXIBLE) – 173 – Remark (5) MECHANISM DECK SECTION-1 (MG-110ES-132) #10 207 #10 206 208 #10 210 209 #10 #10 #13 #14 205 204 203 not supplied 212 202 201 211 212 211 211 212 Ref. No. Part No. Description 201 202 203 204 * 205 3-911-104-01 3-013-099-01 X-3371-264-1 3-927-978-01 X-3372-885-1 WASHER SPRING (EJES) LEVER (NET) ASSY SPRING, TENSION CHASSIS (MZ.EK) ASSY * 206 3-911-106-11 GUIDE (MZ2) Remark Ref. No. Part No. Description * 207 208 209 210 211 X-3372-963-1 3-931-995-01 3-931-453-01 3-930-600-01 X-3371-384-1 COVER (MDEK) ASSY SPRING (EV), TENTION RACK (110) RACK (EV) LEVER (X) ASSY 212 – 174 – 3-377-719-01 WASHER, POLYETHYLENE Remark (6) MECHANISM DECK SECTION-2 (MG-110ES-132) 265 266 267 264 263 268 270 269 262 #17 259 #16 258 260 271 257 272 273 256 261 253 255 270 252 #18 254 251 274 253 M801 Ref. No. Part No. Description 251 252 253 254 255 3-911-105-11 3-911-090-01 3-911-076-11 3-927-977-01 3-908-794-01 CUSHION (M) WHEEL (B2), WORM GEAR (MS) SPRING, COMPRESSION LEVER (T2) (MZ LOCK) 256 257 258 259 260 X-3371-253-1 3-911-074-02 3-364-387-11 3-912-977-01 3-911-083-01 LEVER (KMZT) ASSY GEAR (L2) SPRING (F) GEAR (KS2) ARM (DR) 261 262 263 3-910-400-01 GEAR (EJ3), CAM 3-373-013-01 SPRING (EJ CAM) X-3371-256-1 LEVER (DRT) ASSY Remark Ref. No. Part No. Description 264 265 266 * 267 268 3-377-720-01 3-379-490-11 3-568-315-01 3-911-093-01 X-3371-255-1 WASHER, POLYETHYLENE WASHER, POLYETHYLENE SPRING, COMPRESSION SHAFT (SDR2) SLIDER (DRT) ASSY 269 270 271 272 273 3-364-506-01 3-377-719-01 3-911-096-01 3-375-707-02 3-375-706-03 ROLLER (SL) WASHER, POLYETHYLENE GEAR (DR2) CATCHER (B) CATCHER (F) * 274 M801 – 175 – X-3371-254-1 CHASSIS (MDT) ASSY X-3373-838-1 MOTOR (P) ASSY (DISC EJECT) Remark (7) MECHANISM DECK SECTION-3 (MG-110ES-132) 311 321 312 #19 309 310 #19 #16 308 not supplied 308 316 313 314 315 317 318 307 #11 306 305 304 303 319 302 303 #36 #10 320 #17 302 #10 322 301 Ref. No. Part No. Description BRACKET (DPTT) BEARING (ROLLER) WASHER, 2.5 ROLLER (T) DPT BOARD 312 313 314 315 * 316 X-3371-483-1 3-932-166-01 X-3371-484-1 3-915-913-01 3-364-380-01 ARM (DHK2) ASSY SPRING BRACKET (CPK) ASSY PLATE (CD), CHUCK LEVER, SLIDE SPRING, COMPRESSION ARM (KR) COMPLETE ASSY SPRING (DH2) ROLLER (RK) WASHER, POLYETHYLENE 317 318 319 * 320 321 3-377-720-01 3-364-506-01 X-3371-610-1 1-664-113-12 3-701-438-21 WASHER, POLYETHYLENE ROLLER (SL) GEAR (K) ASSY, ROLLER DOE BOARD WASHER * 322 3-011-255-01 SPACER Ref. No. Part No. Description * 301 302 303 304 * 305 3-930-565-01 3-364-421-01 3-701-438-11 3-909-408-01 1-664-112-12 306 307 308 309 310 3-364-508-01 X-3372-148-1 3-929-743-01 3-932-177-01 3-341-752-11 311 X-3371-482-1 ARM (DHK) ASSY Remark – 176 – Remark (8) MECHANISM DECK SECTION-4 (MG-110ES-132) #10 368 M502 360 361 #20 #10 #21 M501 #10 359 #17 362 SW501 367 #10 369 358 PRG401 370 #10 #21 375 353 355 #16 357 363 374 373 366 377 371 375 354 353 #10 365 #10 376 364 354 #16 372 372 380 372 381 365 382 372 356 379 378 352 351 Part No. Description 369 370 371 372 373 3-930-568-02 3-388-479-01 3-930-298-01 3-377-719-01 3-911-089-01 BRACKET (EVMT) SPRING, COMPRESSION WASHER (TEFLON) WASHER, POLYETHYLENE WHEEL (R2), WORM LOCK (CLAW B) SLIDER (KRT) ASSY SPRING, COMPRESSION CABLE, FLEXIBLE FLAT (4 CORE) SENSOR BOARD 374 375 376 377 378 3-911-088-01 3-377-719-11 X-3371-259-1 3-932-549-01 3-932-550-01 SHAFT (WWR2) WASHER, POLYETHYLENE GEAR (KWT) ASSY BRACKET (BEARING BK) BEARING (BK) CABLE, FLEXIBLE FLAT (8 CORE) GEAR (R), CAM LEVER (KRAT) ASSY GEAR (K) GEAR (L) 379 380 381 382 M501 3-364-424-02 3-910-522-01 X-3371-268-1 3-364-418-04 X-3373-838-1 GEAR (EV) WHEEL (2), WORM BRACKET (EVT GEAR) ASSY GEAR (SL) MOTOR ASSY (ELEVATOR UP/DOWN) Ref. No. Part No. Description * 351 352 353 354 355 X-3371-260-1 3-911-087-01 3-911-097-01 3-308-717-00 3-485-239-00 CHASSIS (EVT) ASSY LOCK (CLAW) SHAFT (LOCK 2) SPRING, COMPRESSION SPRING, COMPRESSION 356 357 358 359 * 360 3-911-102-01 X-3371-261-1 3-353-804-01 1-777-720-11 1-664-110-12 361 362 363 364 365 1-777-721-11 3-364-419-01 X-3371-258-1 3-364-422-01 3-364-417-11 366 367 368 3-364-505-01 WHEEL (C), WORM 3-930-566-01 COVER (GEAR T) 1-643-083-11 MOTOR FLEXIBLE BOARD Remark Ref. No. M502 X-3373-839-1 MOTOR (N) ASSY (DISC LOAD/SAVE) PRG401 1-454-580-21 SOLENOID, PLUNGER SW501 1-571-300-31 SWITCH, ROTARY (HOME/TOP DET) – 177 – Remark (9) OPTICAL PICK-UP SECTION (KSM-400AAM) 404 405 403 #23 402 406 408 #24 407 410 401 #22 409 411 #13 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. Part No. Description * 401 402 * 403 404 * 405 2-625-513-01 2-625-507-01 A-4019-348-B X-2625-607-1 2-625-514-01 BASE, DRIVING GEAR (B2) RETAINER ASSY, THRUST OMD CHASSIS ASSY (F) COVER, FLEXIBLE 406 Remark Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le neméro spécifié. Ref. No. Part No. Description 407 408 ! 409 410 411 2-625-515-01 X-2625-209-1 8-848-310-11 X-2625-210-1 8-835-456-01 RACK (AT) SCREW ASSY, SLED OPTICAL PICK-UP KSS-400A SLED MOTOR GEAR ASSY DC MOTOR SSC-02E01S (SPINDLE) 2-625-516-01 SPRING (A), FEED – 178 – Remark (10) MASTER CONTROL UNIT 458 not supplied not supplied F501 482 453 #7 474 #25 front panel desorption machinery 456 480 457 476 473 454 #7 452 476 #13 477 #25 455 459 #13 454 #7 460 461 #27 462 463 470 481 451 464 465 466 468 469 #26 #27 467 #26 478 #28 Ref. No. Part No. Description 451 452 453 454 455 X-3372-942-1 3-008-496-01 3-008-493-02 3-703-502-31 3-008-462-01 456 * 457 458 459 * 460 Remark #26 tuner control section 471 479 472 Ref. No. Part No. Description PANEL (ORNAMENT) ASSY, FRONT GUIDE (BUTTON RELEASE) WINDOW, REMOTE CONTROL SCREW SPRING, COMPRESSION * 467 468 * 469 470 * 471 3-014-062-01 3-008-466-03 3-014-042-01 3-008-488-02 1-662-633-12 CUSHION (PLATE SUB) PLATE (SUB PANEL A) SHEET (RELAY PCB), INSULATING PANEL (SUB A) TRANSLATION BOARD 3-008-469-01 A-3309-673-A 4-908-792-31 X-3372-943-1 3-011-312-01 BUTTON (RELEASE A) DISPLAY BOARD, COMPLETE SCREW (B2) PANEL (REAR) ASSY PLATE (REAR PANEL), GROUND * 472 473 474 476 477 3-011-875-01 3-162-358-01 1-777-717-11 3-013-796-01 3-013-056-01 PLATE (SUB PANEL), GROUND CUSHION CORD (WITH CONNECTOR) (POWER) SHEET SHEET (F.P. REAR CONNECTOR) 461 462 463 464 465 1-801-564-21 3-008-473-01 3-008-479-01 1-664-508-11 3-008-492-01 LIQUID CRYSTAL DISPLAY MODULE PLATE (FRONT ORNAMENT) ESCUTCHEON (WINDOW) SWITCH FLEXIBLE BOARD PLATE, TRANSPARENT 478 479 480 * 481 * 482 3-013-263-01 3-831-441-11 3-008-475-01 3-014-044-01 3-014-159-01 SHEET (PANEL ATT PC BOARD) CLOTH, UNWEAVED (25X6X0.5) EMBLEM (XES LIGHT GUIDE) SPACER (FRONT PANEL) SPACER (RELEASE MECH) 466 3-008-468-01 BUTTON (A) F501 – 179 – 1-532-731-11 FUSE (3A/32V) Remark (11) FRONT PANEL DESORPTION MACHINERY 510 523 #8 #22 not supplied 511 509 528 508 522 512 #8 #22 524 514 513 507 515 516 506 #30 504 525 509 #22 517 526 505 524 508 533 518 #30 519 #30 503 502 510 #13 #13 #29 530 520 513 528 521 527 529 #8 501 #30 M1 532 530 531 Part No. Description 518 519 520 521 522 3-008-430-01 3-008-480-01 3-008-481-01 3-008-429-01 X-3372-938-1 GEAR (C) REFLECTOR SEAL, REFLECTION GEAR (B) LEVER (X) ASSY COVER (SWITCH L) LEVER (LOCK L) SPRING (LOCK LEVER) SHAFT (LOCK LEVER) GUIDE (LEVER) * 523 524 525 526 * 527 3-008-460-01 3-385-409-01 3-008-461-01 3-008-458-01 1-662-634-12 CASE (LOCK UPPER) WASHER, POLYETHYLENE SPRING (RACK R), TENSION RACK (R) OPEN/CLOSE 1 BOARD SPRING (RACK L), TENSION RACK (L) ASSY WASHER, STOPPER FLEXIBLE 1 BOARD COVER (SWITCH R) 528 529 530 * 531 532 3-377-719-11 X-3372-939-1 4-932-613-01 X-3372-937-1 X-3372-956-1 WASHER, POLYETHYLENE CLUTCH ASSY SPACER CASE (LOCK LOWER) ASSY SPRING (LOCK R) ASSY Ref. No. Part No. Description * 501 * 502 503 * 504 505 1-662-635-12 2-277-426-01 3-906-712-01 3-008-465-01 X-3372-957-1 OPEN/CLOSE 2 BOARD CLAMP SCREW (2.6X6) (CU), +PTT BRACKET (MOTOR) SPRING (LOCK L) ASSY 506 507 508 509 510 3-008-478-01 3-008-431-01 3-008-457-01 3-008-459-01 3-008-440-01 511 512 513 514 515 3-008-433-01 X-3372-940-1 3-701-436-11 1-662-967-11 3-008-477-01 516 517 1-662-968-11 FLEXIBLE 2 BOARD 3-008-474-01 LEVER (LOCK R) Remark Ref. No. 533 M1 – 180 – Remark 3-325-697-11 WASHER A-3301-104-A MOTOR ASSY (FRONT PANEL DESORPTION) (12) TUNER CONTROL SECTION 561 559 #34 557 556 558 565 #8 #8 B 562 #34 556 B 558 A #3 557 A 563 552 #8 #8 554 556 555 #33 560 555 #32 556 564 551 Ref. No. Part No. Description Remark * 551 * 552 * 554 555 556 3-008-593-01 A-3313-237-A 3-011-594-01 3-912-525-01 3-010-448-01 SHEET (MAIN BOARD) MAIN BOARD, COMPLETE HEAT SINK (MAIN BOARD) SCREW (2.6X4) (CU), +B SPACER (SHIELD CASE) * 557 558 559 3-010-447-01 RETAINER 3-010-449-01 SPACER A-3301-206-A TUNER (U) ASSY (FM/AM TUNER UNIT) Ref. No. * * * * Part No. Description 560 561 562 563 564 3-912-956-11 3-008-455-01 3-008-464-01 3-011-587-01 3-008-456-01 SCREW (2.6X6) (CU), +BVTT CHASSIS (MAIN TOP) CHASSIS (MAIN REAR) HEAT SINK (MAIN REAR) CHASSIS (MAIN BOTTOM) 565 1-782-714-11 CORD (WITH CONNECTOR) (ANT) (SUB (FM)/MAIN (FM/AM)) – 181 – Remark (13) BRACKET ASS’Y SECTION 604 611 612 609 605 606 607 608 610 #35 #25 604 617 614 613 618 603 618 615 602 616 #29 601 Ref. No. Part No. Description * 601 602 603 604 605 1-663-878-12 3-010-451-01 3-010-450-01 3-906-376-01 3-934-757-01 TRANSLATION (HIDE) BOARD CASE (LOWER-ATT) CASE (UPPER-ATT) SCREW (2.6X6) HOLDER (LOCK) 606 607 608 609 3-934-765-01 3-934-756-01 3-934-758-01 3-934-755-01 SPRING (B) ARM (LOCK) SPRING (A) SHAFT (LOCK) Remark Ref. No. Part No. Description 610 611 612 * 613 614 4-908-618-21 3-009-517-01 3-009-518-01 1-663-877-12 X-3373-153-1 SCREW (+BTP) (2X6) PANEL (ATT) BRACKET (ATT REAR) TRANSLATION (CONNECTOR) BOARD BRACKET (ATT-F) SUB ASSY 615 616 617 618 1-782-199-11 1-782-200-11 3-013-263-01 1-543-798-11 CORD (WITH CONNECTOR) (DIN) CORD (WITH CONNECTOR) (HIDE) SHEET (PANEL ATT PC BOARD) FILTER, CLAMP (FERRITE CORE) – 182 – Remark SECTION 9 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable CHANGER • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u: µ, for example: uA. . : µA. . uPA. . : µPA. . uPB. . : µPB. . uPC. . : µPC. . uPD. . : µPD. . • CAPACITORS uF: µF • COILS uH: µH Ref. No. Part No. Description Remark * A-3309-787-A CHANGER BOARD, COMPLETE ************************ * 3-008-214-01 HEAT SINK (SUB) 3-905-560-01 SCREW (2.6×6) (CU), +PTT < CAPACITOR > C301 C302 C303 C304 C305 1-164-004-11 1-164-004-11 1-104-913-11 1-164-004-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 10uF 0.1uF 0.1uF 10% 10% 20% 10% 10% 25V 25V 16V 25V 25V C306 C307 C308 C309 C311 1-125-701-11 1-164-004-11 1-164-004-11 1-164-004-11 1-164-232-11 DOUBLE LAYER CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.047F 0.1uF 0.1uF 0.1uF 0.01uF 5.5V 10% 25V 10% 25V 10% 25V 50V C401 C402 C403 C404 C501 1-164-004-11 1-164-004-11 1-164-004-11 1-164-004-11 1-163-005-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 470PF 10% 10% 10% 10% 10% 25V 25V 25V 25V 50V C502 C504 C505 C506 C507 1-164-004-11 1-163-005-11 1-164-004-11 1-163-011-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 470PF 0.1uF 0.0015uF 0.1uF 10% 10% 10% 10% 10% 25V 50V 25V 50V 25V C508 C509 C510 C511 C512 1-163-809-11 1-107-823-11 1-164-161-11 1-163-251-11 1-107-823-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.047uF 0.47uF 0.0022uF 100PF 0.47uF 10% 10% 10% 5% 10% 25V 16V 100V 50V 16V C513 C514 C515 C516 C517 1-164-232-11 1-164-004-11 1-164-004-11 1-164-004-11 1-107-823-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.1uF 0.1uF 0.1uF 0.47uF 10% 10% 10% 10% 50V 25V 25V 25V 16V C520 C521 C522 C523 C524 1-163-231-11 1-164-232-11 1-164-004-11 1-164-004-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 15PF 0.01uF 0.1uF 0.1uF 0.1uF 5% C525 C526 1-664-004-11 CERAMIC CHIP 1-104-823-11 TANTAL. CHIP 0.1uF 47uF 10% 25V 20% 16V 50V 50V 10% 25V 10% 25V 10% 25V Ref. No. Part No. The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiquens pour la sécurité. Ne les remplacer que par une pièce portant le neméro spécifié. When indicating parts by reference number, please include the board. Description Remark C530 C531 C532 1-164-232-11 CERAMIC CHIP 1-164-004-11 CERAMIC CHIP 1-109-982-11 CERAMIC CHIP 0.01uF 0.1uF 1uF 50V 10% 25V 10% 10V C601 C602 C901 C902 C903 1-164-004-11 1-164-004-11 1-109-982-11 1-128-426-11 1-128-426-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT 0.1uF 0.1uF 1uF 47uF 47uF 10% 10% 10% 20% 20% 25V 25V 10V 25V 25V C904 C905 C906 C907 C908 1-109-982-11 1-128-426-11 1-128-426-11 1-164-004-11 1-125-701-11 CERAMIC CHIP ELECT ELECT CERAMIC CHIP DOUBLE LAYER 1uF 47uF 47uF 0.1uF 0.047F 10% 20% 20% 10% 10V 25V 25V 25V 5.5V C909 C910 C911 C912 C913 1-128-422-11 1-128-426-11 1-128-422-11 1-109-982-11 1-164-004-11 ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP 100uF 47uF 100uF 1uF 0.1uF 20% 20% 20% 10% 10% 16V 25V 16V 10V 25V C914 C915 C916 C917 C920 1-128-426-11 1-128-426-11 1-128-426-11 1-128-426-11 1-164-004-11 ELECT ELECT ELECT ELECT CERAMIC CHIP 47uF 47uF 47uF 47uF 0.1uF 20% 20% 20% 20% 10% 25V 25V 25V 25V 25V C921 C922 C923 C924 C951 1-164-004-11 1-164-004-11 1-128-426-11 1-164-232-11 1-163-017-00 CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 47uF 0.01uF 0.0047uF 10% 25V 10% 25V 20% 25V 50V 5% 50V C952 C953 C954 C955 1-164-004-11 1-164-004-11 1-163-009-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.001uF 0.1uF 10% 10% 10% 10% < CONNECTOR > * CNJ301 CNJ501 CNJ601 CNP302 CNP901 1-764-908-11 1-778-819-11 1-778-818-11 1-580-057-11 1-779-122-11 CONNECTOR, FFC/FPC (ZIF) 10P CONNECTOR, FFC/FPC (ZIF) 22P CONNECTOR, FFC/FPC (ZIF) 13P PIN, CONNECTOR 4P PIN, CONNECTOR 12P CNP902 1-779-069-21 PIN, CONNECTOR 6P < DIODE > D301 – 183 – 8-719-801-78 DIODE 1SS184 25V 25V 50V 25V CHANGER Ref. No. Part No. Description Remark D302 D303 D901 D902 8-719-975-40 8-719-038-48 8-719-801-78 8-719-106-08 DIODE DIODE DIODE DIODE RB411D 1SS319 (TE85R) 1SS184 RD6.2M-B2 D903 D904 D905 D906 D908 8-719-801-78 8-719-038-48 8-719-105-99 8-719-210-33 8-719-210-33 DIODE DIODE DIODE DIODE DIODE 1SS184 1SS319 (TE85R) RD6.2M-B1 EC10DS2 EC10DS2 D951 D952 D953 D954 D955 8-719-975-40 8-719-106-08 8-719-106-08 8-719-975-40 8-719-975-40 DIODE DIODE DIODE DIODE DIODE RB411D RD6.2M-B2 RD6.2M-B2 RB411D RB411D D956 8-719-106-08 DIODE RD6.2M-B2 Ref. No. Part No. Description Remark R310 1-216-295-00 CONDUCTOR, CHIP (2012) R315 R316 R319 R322 R323 1-216-061-00 1-216-089-00 1-216-089-00 1-216-081-00 1-216-295-00 METAL CHIP 3.3K METAL CHIP 47K METAL CHIP 47K METAL CHIP 22K CONDUCTOR, CHIP (2012) 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R330 R331 R332 R333 R334 1-216-097-00 1-216-089-00 1-216-049-00 1-216-089-00 1-216-049-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 47K 1K 47K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R335 R336 R337 R338 R339 1-216-089-00 1-216-073-00 1-216-089-00 1-216-029-00 1-216-097-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47K 10K 47K 150 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R401 R402 R403 R501 R502 1-216-041-00 1-216-041-00 1-216-041-00 1-216-073-00 1-216-097-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470 470 470 10K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R503 R504 R505 R506 R507 1-216-073-00 1-216-073-00 1-216-121-00 1-216-295-00 1-216-061-00 METAL CHIP 10K METAL CHIP 10K METAL CHIP 1M CONDUCTOR, CHIP (2012) METAL CHIP 3.3K 5% 5% 5% 1/10W 1/10W 1/10W 5% 1/10W R508 R509 R510 R511 R512 1-216-113-00 1-216-061-00 1-216-121-00 1-216-097-00 1-216-041-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R513 R514 R515 R516 R517 1-216-041-00 1-216-073-00 1-216-041-00 1-216-295-00 1-216-295-00 METAL CHIP 470 METAL CHIP 10K METAL CHIP 470 CONDUCTOR, CHIP (2012) CONDUCTOR, CHIP (2012) 5% 5% 5% 1/10W 1/10W 1/10W R518 R519 R520 R521 R524 1-216-295-00 1-216-041-00 1-216-295-00 1-216-041-00 1-216-033-00 CONDUCTOR, CHIP (2012) METAL CHIP 470 CONDUCTOR, CHIP (2012) METAL CHIP 470 METAL CHIP 220 5% 1/10W 5% 5% 1/10W 1/10W R526 R527 R529 R531 R532 1-216-037-00 1-216-037-00 1-216-081-00 1-216-053-00 1-216-105-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 330 330 22K 1.5K 220K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R533 R534 R535 R601 R602 1-216-025-00 1-216-105-00 1-216-089-00 1-216-041-00 1-216-085-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 220K 47K 470 33K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R603 R901 R902 R903 R904 1-216-073-00 1-216-089-00 1-216-689-11 1-216-089-00 1-216-057-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 47K 39K 47K 2.2K 5% 5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R905 R906 1-216-089-00 METAL CHIP 1-216-077-00 METAL CHIP 47K 15K 5% 5% 1/10W 1/10W < FERRITE BEAD > FB501 FB502 FB503 1-500-239-21 BEAD, FERRITE (CHIP) 1-500-239-21 BEAD, FERRITE (CHIP) 1-500-239-21 BEAD, FERRITE (CHIP) < IC > IC301 IC302 IC303 IC304 IC305 8-752-887-16 8-759-443-04 8-752-882-50 8-752-365-22 8-759-243-19 IC IC IC IC IC CXP846P48Q-1-004 AT24C32N-10SI-TR CXP83413-035Q CXK581000AM-10LL TC7SU04F IC401 IC402 IC403 IC501 IC502 8-752-373-27 8-759-342-14 8-759-342-14 8-752-379-09 8-759-925-90 IC IC IC IC IC CXD2512AQ uPD424400GS-60-9JD uPD424400GS-60-9JD CXD2540Q SN74HC74ANS IC503 IC504 IC505 IC601 IC901 8-759-158-96 8-759-439-67 8-759-082-58 8-752-344-48 8-759-231-53 IC IC IC IC IC TC9246F-TP1 TC7W126FU (TE12R) TC7W08FU CXD2501Q TA7805S IC902 IC903 IC904 IC905 IC951 8-759-231-53 8-759-443-41 8-759-231-53 8-759-054-12 8-759-284-87 IC IC IC IC IC TA7805S RH5VL40AA-T1C TA7805S PQ09RA1 MM1284XFFE < TRANSISTOR > Q301 Q302 Q303 Q304 Q901 8-729-027-31 8-729-027-31 8-729-027-31 8-729-901-00 8-729-230-49 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTA124EKA-T146 DTA124EKA-T146 DTA124EKA-T146 DTC124EK 2SC2712-YG Q902 Q903 Q904 Q905 8-729-027-31 8-729-016-11 8-729-901-00 8-729-016-83 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTA124EKA-T146 2SD1507M DTC124EK 2SB1446 < RESISTOR/CHIP CONDUCTOR > R301 R304 R305 R306 1-216-081-00 1-216-065-00 1-216-065-00 1-216-081-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22K 4.7K 4.7K 22K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W – 184 – 470K 3.3K 1M 100K 470 CHANGER Ref. No. Part No. Description Remark Ref. No. Part No. DAC Description Remark R907 R908 R910 1-216-061-00 METAL CHIP 3.3K 1-216-073-00 METAL CHIP 10K 1-216-295-00 CONDUCTOR, CHIP (2012) 5% 5% 1/10W 1/10W C1204 C1205 1-104-852-11 TANTAL. CHIP 1-104-852-11 TANTAL. CHIP 22uF 22uF 20% 10V 20% 10V R911 R912 R951 1-216-061-00 METAL CHIP 1-216-061-00 METAL CHIP 1-216-089-00 METAL CHIP 5% 5% 5% 1/10W 1/10W 1/10W C1206 C1207 C1208 C1209 C1210 1-104-551-11 1-104-551-11 1-104-852-11 1-124-710-11 1-110-569-11 FILM CHIP FILM CHIP TANTAL. CHIP ELECT TANTAL. CHIP 0.01uF 0.01uF 22uF 100uF 47uF 5% 5% 20% 20% 20% 16V 16V 10V 35V 6.3V C1211 C1212 C1213 C1214 C1215 1-104-852-11 1-104-852-11 1-104-551-11 1-104-551-11 1-104-852-11 TANTAL. CHIP TANTAL. CHIP FILM CHIP FILM CHIP TANTAL. CHIP 22uF 22uF 0.01uF 0.01uF 22uF 20% 20% 5% 5% 20% 10V 10V 16V 16V 10V C1216 C1217 C1218 C1219 C1220 1-124-710-11 1-110-569-11 1-136-165-00 1-136-165-00 1-136-230-00 ELECT TANTAL. CHIP FILM FILM FILM 100uF 47uF 0.1uF 0.1uF 0.0022uF 20% 20% 5% 5% 5% 35V 6.3V 50V 50V 100V C1221 C1222 C1223 C1224 C1225 1-136-250-11 1-136-165-00 1-136-165-00 1-136-230-00 1-136-250-11 FILM FILM FILM FILM FILM 0.001uF 0.1uF 0.1uF 0.0022uF 0.001uF 5% 5% 5% 5% 5% 100V 50V 50V 100V 100V C1226 C1227 C1230 C1231 C1232 1-136-165-00 1-136-165-00 1-136-165-00 1-136-165-00 1-124-910-11 FILM FILM FILM FILM ELECT 0.1uF 0.1uF 0.1uF 0.1uF 47uF 5% 5% 5% 5% 20% 50V 50V 50V 50V 50V C1233 C1234 C1301 C1302 C1303 1-124-910-11 1-124-721-11 1-104-851-11 1-163-009-11 1-104-551-11 ELECT ELECT TANTAL. CHIP CERAMIC CHIP FILM CHIP 47uF 10uF 10uF 0.001uF 0.01uF 20% 20% 20% 10% 5% 50V 50V 10V 50V 16V C1304 C1305 C1306 C1307 C1308 1-104-852-11 1-104-852-11 1-104-551-11 1-104-551-11 1-104-852-11 TANTAL. CHIP TANTAL. CHIP FILM CHIP FILM CHIP TANTAL. CHIP 22uF 22uF 0.01uF 0.01uF 22uF 20% 20% 5% 5% 20% 10V 10V 16V 16V 10V C1309 C1310 C1311 C1312 C1313 1-124-710-11 1-110-569-11 1-104-852-11 1-104-852-11 1-104-551-11 ELECT TANTAL. CHIP TANTAL. CHIP TANTAL. CHIP FILM CHIP 100uF 47uF 22uF 22uF 0.01uF 20% 20% 20% 20% 5% 35V 6.3V 10V 10V 16V C1314 C1315 C1316 C1317 C1318 1-104-551-11 1-104-852-11 1-124-710-11 1-110-569-11 1-136-165-00 FILM CHIP TANTAL. CHIP ELECT TANTAL. CHIP FILM 0.01uF 22uF 100uF 47uF 0.1uF 5% 20% 20% 20% 5% 16V 10V 35V 6.3V 50V C1319 C1320 C1321 C1322 C1323 1-136-165-00 1-136-230-00 1-136-250-11 1-136-165-00 1-136-165-00 FILM FILM FILM FILM FILM 0.1uF 0.0022uF 0.001uF 0.1uF 0.1uF 5% 5% 5% 5% 5% 50V 100V 100V 50V 50V C1324 C1325 C1326 C1327 C1330 1-136-230-00 1-136-250-11 1-136-165-00 1-136-165-00 1-136-165-00 FILM FILM FILM FILM FILM 0.0022uF 0.001uF 0.1uF 0.1uF 0.1uF 5% 5% 5% 5% 5% 100V 100V 50V 50V 50V C1331 1-136-165-00 FILM 0.1uF 5% 50V 3.3K 3.3K 47K < THERMISTOR > TH301 TH302 1-810-421-11 THERMISTOR 1-810-421-11 THERMISTOR < VIBRATOR > X301 1-760-479-11 VIBRATOR, CERAMIC (8MHz) X302 1-760-365-11 VIBRATOR, CERAMIC (10MHz) X502 1-767-366-21 VIBRATOR, CERAMIC (16.93MHz) ************************************************************ A-3309-659-A DAC BOARD, COMPLETE ******************** * < CAPACITOR > C1010 C1011 C1012 C1101 C1102 1-164-004-11 1-124-673-11 1-164-004-11 1-104-851-11 1-163-009-11 CERAMIC CHIP ELECT CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP 0.1uF 100uF 0.1uF 10uF 0.001uF 10% 20% 10% 20% 10% 25V 10V 25V 10V 50V C1103 C1104 C1105 C1106 C1107 1-104-551-11 1-104-852-11 1-104-852-11 1-104-551-11 1-104-551-11 FILM CHIP TANTAL. CHIP TANTAL. CHIP FILM CHIP FILM CHIP 0.01uF 22uF 22uF 0.01uF 0.01uF 5% 20% 20% 5% 5% 16V 10V 10V 16V 16V C1108 C1109 C1110 C1111 C1112 1-104-852-11 1-124-710-11 1-110-569-11 1-104-852-11 1-104-852-11 TANTAL. CHIP ELECT TANTAL. CHIP TANTAL. CHIP TANTAL. CHIP 22uF 100uF 47uF 22uF 22uF 20% 20% 20% 20% 20% 10V 35V 6.3V 10V 10V C1113 C1114 C1115 C1116 C1117 1-104-551-11 1-104-551-11 1-104-852-11 1-124-710-11 1-110-569-11 FILM CHIP FILM CHIP TANTAL. CHIP ELECT TANTAL. CHIP 0.01uF 0.01uF 22uF 100uF 47uF 5% 5% 20% 20% 20% 16V 16V 10V 35V 6.3V C1118 C1119 C1120 C1121 C1122 1-136-165-00 1-136-165-00 1-136-230-00 1-136-250-11 1-136-165-00 FILM FILM FILM FILM FILM 0.1uF 0.1uF 0.0022uF 0.001uF 0.1uF 5% 5% 5% 5% 5% 50V 50V 100V 100V 50V C1123 C1124 C1125 C1126 C1127 1-136-165-00 1-136-230-00 1-136-250-11 1-136-165-00 1-136-165-00 FILM FILM FILM FILM FILM 0.1uF 0.0022uF 0.001uF 0.1uF 0.1uF 5% 5% 5% 5% 5% 50V 100V 100V 50V 50V C1130 C1131 C1132 C1133 C1134 1-136-165-00 1-136-165-00 1-124-910-11 1-124-910-11 1-124-721-11 FILM FILM ELECT ELECT ELECT 0.1uF 0.1uF 47uF 47uF 10uF 5% 5% 20% 20% 20% 50V 50V 50V 50V 50V C1201 C1202 C1203 1-104-851-11 TANTAL. CHIP 1-163-009-11 CERAMIC CHIP 1-104-551-11 FILM CHIP 10uF 0.001uF 0.01uF 20% 10V 10% 50V 5% 16V – 185 – DAC Ref. No. Remark Ref. No. Part No. Description C1332 C1333 C1334 C1401 1-124-910-11 1-124-910-11 1-124-721-11 1-164-004-11 ELECT ELECT ELECT CERAMIC CHIP 47uF 47uF 10uF 0.1uF 20% 20% 20% 10% 50V 50V 50V 25V C1639 C1640 C1402 C1403 C1404 C1405 C1406 1-164-004-11 1-104-851-11 1-164-004-11 1-107-206-00 1-107-206-00 CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP MICA MICA 0.1uF 10uF 0.1uF 15PF 15PF 10% 20% 10% 5% 5% 25V 10V 25V 500V 500V CN1001 CN1010 CN1011 CN1501 * CN1601 C1501 C1502 C1503 C1504 C1505 1-124-699-11 1-136-165-00 1-124-710-11 1-124-699-11 1-136-165-00 ELECT FILM ELECT ELECT FILM 220uF 0.1uF 100uF 220uF 0.1uF 20% 5% 20% 20% 5% 25V 50V 35V 25V 50V C1506 C1507 C1508 C1509 C1510 1-124-710-11 1-124-699-11 1-136-165-00 1-124-710-11 1-124-699-11 ELECT ELECT FILM ELECT ELECT 100uF 220uF 0.1uF 100uF 220uF 20% 20% 5% 20% 20% 35V 25V 50V 35V 25V C1511 C1512 C1601 C1602 C1603 1-136-165-00 1-124-710-11 1-124-910-11 1-124-910-11 1-124-910-11 FILM ELECT ELECT ELECT ELECT 0.1uF 100uF 47uF 47uF 47uF 5% 20% 20% 20% 20% 50V 35V 50V 50V 50V C1604 C1605 C1606 C1607 C1608 1-136-808-11 1-136-808-11 1-136-165-00 1-136-165-00 1-163-235-11 FILM FILM FILM FILM CERAMIC CHIP 100PF 100PF 0.1uF 0.1uF 22PF 5% 5% 5% 5% 5% 100V 100V 50V 50V 50V C1609 C1610 C1611 C1612 C1613 1-163-235-11 1-163-235-11 1-163-235-11 1-136-820-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP FILM CERAMIC CHIP 22PF 22PF 22PF 0.01uF 0.1uF 5% 5% 5% 5% 10% 50V 50V 50V 100V 25V C1614 C1615 C1616 C1617 C1618 1-104-851-11 1-164-004-11 1-136-165-00 1-136-165-00 1-136-820-11 TANTAL. CHIP CERAMIC CHIP FILM FILM FILM 10uF 0.1uF 0.1uF 0.1uF 0.01uF 20% 10% 5% 5% 5% 10V 25V 50V 50V 100V C1619 C1620 C1621 C1622 C1623 1-124-673-11 1-136-165-00 1-124-673-11 1-163-231-11 1-163-231-11 ELECT FILM ELECT CERAMIC CHIP CERAMIC CHIP 100uF 0.1uF 100uF 15PF 15PF 20% 5% 20% 5% 5% 10V 50V 10V 50V 50V C1624 C1625 C1626 C1627 C1628 1-163-231-11 1-163-231-11 1-136-165-00 1-136-165-00 1-136-165-00 CERAMIC CHIP CERAMIC CHIP FILM FILM FILM 15PF 15PF 0.1uF 0.1uF 0.1uF 5% 5% 5% 5% 5% 50V 50V 50V 50V 50V C1629 C1630 C1631 C1632 C1633 1-136-165-00 1-164-004-11 1-164-004-11 1-136-165-00 1-136-165-00 FILM CERAMIC CHIP CERAMIC CHIP FILM FILM 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 5% 10% 10% 5% 5% 50V 25V 25V 50V 50V C1634 C1635 C1636 C1637 C1638 1-136-165-00 1-136-165-00 1-164-004-11 1-104-551-11 1-164-004-11 FILM FILM CERAMIC CHIP FILM CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.01uF 0.1uF 5% 5% 10% 5% 10% 50V 50V 25V 16V 25V Part No. Description 1-104-551-11 FILM 1-164-232-11 CERAMIC CHIP Remark 0.01uF 0.01uF 5% < CONNECTOR > 1-779-119-11 1-778-939-11 1-506-945-11 1-506-947-11 1-766-324-11 PIN, CONNECTOR 5P CONNECTOR, FFC/FPC (ZIF) 30P PIN, CONNECTOR 3P PIN, CONNECTOR 6P CONNECTOR, FFC/FPC (ZIF) 8P CN1602 1-779-120-11 PIN, CONNECTOR 8P < DIODE > D1101 D1102 D1103 D1104 D1105 8-719-800-76 8-719-800-76 8-719-800-76 8-719-800-76 8-719-800-76 DIODE DIODE DIODE DIODE DIODE 1SS226 1SS226 1SS226 1SS226 1SS226 D1106 D1107 D1201 D1202 D1203 8-719-800-76 8-719-052-12 8-719-800-76 8-719-800-76 8-719-800-76 DIODE DIODE DIODE DIODE DIODE 1SS226 1SS376TE-17 1SS226 1SS226 1SS226 D1204 D1205 D1206 D1207 D1301 8-719-800-76 8-719-800-76 8-719-800-76 8-719-052-12 8-719-800-76 DIODE DIODE DIODE DIODE DIODE 1SS226 1SS226 1SS226 1SS376TE-17 1SS226 D1302 D1303 D1304 D1305 D1306 8-719-800-76 8-719-800-76 8-719-800-76 8-719-800-76 8-719-800-76 DIODE DIODE DIODE DIODE DIODE 1SS226 1SS226 1SS226 1SS226 1SS226 D1307 D1601 D1602 D1603 D1604 8-719-052-12 8-719-404-49 8-719-404-49 8-719-404-49 8-719-404-49 DIODE DIODE DIODE DIODE DIODE 1SS376TE-17 MA111 MA111 MA111 MA111 D1605 D1606 D1607 D1608 D1609 8-719-404-49 8-719-404-49 8-719-404-49 8-719-404-49 8-719-052-12 DIODE DIODE DIODE DIODE DIODE MA111 MA111 MA111 MA111 1SS376TE-17 D1610 D1611 D1612 D1613 D1614 8-719-052-12 8-719-052-12 8-719-422-64 8-719-422-64 8-719-422-64 DIODE DIODE DIODE DIODE DIODE 1SS376TE-17 1SS376TE-17 MA8062-M MA8062-M MA8062-M D1615 8-719-422-64 DIODE MA8062-M < FERRITE BEAD > FB1101 FB1201 FB1301 FB1401 FB1402 1-414-235-11 1-414-235-11 1-414-235-11 1-414-235-11 1-414-235-11 INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD FB1403 1-414-235-11 INDUCTOR, FERRITE BEAD FB1404 1-414-235-11 INDUCTOR, FERRITE BEAD FB1601 1-414-235-11 INDUCTOR, FERRITE BEAD – 186 – 16V 50V DAC Ref. No. Part No. Description Remark FB1602 1-414-235-11 INDUCTOR, FERRITE BEAD FB1603 1-414-235-11 INDUCTOR, FERRITE BEAD FB1604 1-414-235-11 INDUCTOR, FERRITE BEAD Ref. No. Part No. Description Remark R1015 R1101 R1102 R1103 R1104 1-216-025-00 1-216-017-00 1-216-025-00 1-216-017-00 1-216-017-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 47 100 47 47 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1105 R1106 R1107 R1108 R1109 1-260-001-11 1-259-995-11 1-259-998-11 1-259-998-11 1-260-001-11 CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF 2.7K 1K 1.8K 1.8K 2.7K 2% 2% 2% 2% 2% 1/8W 1/8W 1/8W 1/8W 1/8W R1110 R1111 R1112 R1113 R1114 1-259-995-11 1-259-998-11 1-259-998-11 1-260-009-11 1-260-004-11 CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF 1K 1.8K 1.8K 12K 4.7K 2% 2% 2% 2% 2% 1/8W 1/8W 1/8W 1/8W 1/8W R1115 R1116 R1117 R1118 R1119 1-260-009-11 1-260-004-11 1-259-983-11 1-259-983-11 1-260-016-11 CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF 12K 4.7K 100 100 47K 2% 2% 2% 2% 2% 1/8W 1/8W 1/8W 1/8W 1/8W R1120 R1121 R1122 R1123 R1124 1-260-016-11 1-259-971-11 1-260-005-11 1-260-005-11 1-260-005-11 CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF 47K 10 5.6K 5.6K 5.6K 2% 2% 2% 2% 2% 1/8W 1/8W 1/8W 1/8W 1/8W R1125 R1126 R1127 R1201 R1202 1-260-005-11 1-216-001-00 1-216-073-00 1-216-017-00 1-216-025-00 CARBON MELF METAL CHIP METAL CHIP METAL CHIP METAL CHIP 5.6K 10 10K 47 100 2% 5% 5% 5% 5% 1/8W 1/10W 1/10W 1/10W 1/10W R1203 R1204 R1205 R1206 R1207 1-216-017-00 1-216-017-00 1-260-001-11 1-259-995-11 1-259-998-11 METAL CHIP METAL CHIP CARBON MELF CARBON MELF CARBON MELF 47 47 2.7K 1K 1.8K 5% 5% 2% 2% 2% 1/10W 1/10W 1/8W 1/8W 1/8W R1208 R1209 R1210 R1211 R1212 1-259-998-11 1-260-001-11 1-259-995-11 1-259-998-11 1-259-998-11 CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF 1.8K 2.7K 1K 1.8K 1.8K 2% 2% 2% 2% 2% 1/8W 1/8W 1/8W 1/8W 1/8W R1213 R1214 R1215 R1216 R1217 1-260-009-11 1-260-004-11 1-260-009-11 1-260-004-11 1-259-983-11 CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF 12K 4.7K 12K 4.7K 100 2% 2% 2% 2% 2% 1/8W 1/8W 1/8W 1/8W 1/8W R1218 R1219 R1220 R1221 R1222 1-259-983-11 1-260-016-11 1-260-016-11 1-259-971-11 1-260-005-11 CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF 100 47K 47K 10 5.6K 2% 2% 2% 2% 2% 1/8W 1/8W 1/8W 1/8W 1/8W R1223 R1224 R1225 R1226 R1227 1-260-005-11 1-260-005-11 1-260-005-11 1-216-001-00 1-216-073-00 CARBON MELF CARBON MELF CARBON MELF METAL CHIP METAL CHIP 5.6K 5.6K 5.6K 10 10K 2% 2% 2% 5% 5% 1/8W 1/8W 1/8W 1/10W 1/10W R1301 R1302 R1303 R1304 1-216-017-00 1-216-025-00 1-216-017-00 1-216-017-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47 100 47 47 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W < IC > IC1010 IC1101 IC1102 IC1103 IC1104 8-759-186-77 8-759-169-03 8-759-425-06 8-759-425-06 8-759-443-33 IC IC IC IC IC TC74VHC541F SM5843AS1-ET PCM1702U-K-T1 PCM1702U-K-T1 OPA2132PA IC1105 IC1106 IC1107 IC1201 IC1202 8-759-443-33 8-759-443-35 8-759-900-72 8-759-169-03 8-759-425-06 IC IC IC IC IC OPA2132PA CS3310-KP NE5532P SM5843AS1-ET PCM1702U-K-T1 IC1203 IC1204 IC1205 IC1206 IC1207 8-759-425-06 8-759-443-33 8-759-443-33 8-759-443-35 8-759-900-72 IC IC IC IC IC PCM1702U-K-T1 OPA2132PA OPA2132PA CS3310-KP NE5532P IC1301 IC1302 IC1303 IC1304 IC1305 8-759-169-03 8-759-425-06 8-759-425-06 8-759-443-33 8-759-443-33 IC IC IC IC IC SM5843AS1-ET PCM1702U-K-T1 PCM1702U-K-T1 OPA2132PA OPA2132PA IC1306 IC1307 IC1401 IC1402 IC1403 8-759-443-35 8-759-900-72 8-759-186-44 8-759-186-14 8-759-081-46 IC IC IC IC IC CS3310-KP NE5532P TC74VHC125F (EL) TC74VHC393F (EL) TC74VHCU04F IC1501 IC1502 IC1503 IC1504 IC1601 8-759-231-59 8-759-448-79 8-759-231-53 8-759-443-31 8-759-443-33 IC IC IC IC IC TA7815S TA79015P TA7805S TA79005P OPA2132PA IC1602 IC1603 IC1604 IC1605 IC1606 8-759-443-33 8-759-900-72 8-759-900-72 8-759-900-72 8-759-083-94 IC IC IC IC IC OPA2132PA NE5532P NE5532P NE5532P TC7W74FU IC1607 8-759-336-17 IC AK5390-VS < COIL > L1401 1-412-060-11 INDUCTOR CHIP 22uH < TRANSISTOR > Q1001 Q1601 Q1602 8-729-421-22 TRANSISTOR UN2211 8-729-421-22 TRANSISTOR UN2211 8-729-421-22 TRANSISTOR UN2211 < RESISTOR > R1010 R1011 R1012 R1013 R1014 1-216-025-00 1-216-033-00 1-216-033-00 1-216-033-00 1-216-017-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 220 220 220 47 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W – 187 – DAC Ref. No. DISPLAY Part No. Description Remark Ref. No. Part No. Description Remark R1305 1-260-001-11 CARBON MELF 2.7K 2% 1/8W R1306 R1307 R1308 R1309 R1310 1-259-995-11 1-259-998-11 1-259-998-11 1-260-001-11 1-259-995-11 CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF 1K 1.8K 1.8K 2.7K 1K 2% 2% 2% 2% 2% 1/8W 1/8W 1/8W 1/8W 1/8W R1311 R1312 R1313 R1314 R1315 1-259-998-11 1-259-998-11 1-260-009-11 1-260-004-11 1-260-009-11 CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF 1.8K 1.8K 12K 4.7K 12K 2% 2% 2% 2% 2% 1/8W 1/8W 1/8W 1/8W 1/8W R1316 R1317 R1318 R1319 R1320 1-260-004-11 1-259-983-11 1-259-983-11 1-260-016-11 1-260-016-11 CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF 4.7K 100 100 47K 47K 2% 2% 2% 2% 2% 1/8W 1/8W 1/8W 1/8W 1/8W BZ811 R1321 R1322 R1323 R1324 R1325 1-259-971-11 1-260-005-11 1-260-005-11 1-260-005-11 1-260-005-11 CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF 10 5.6K 5.6K 5.6K 5.6K 2% 2% 2% 2% 2% 1/8W 1/8W 1/8W 1/8W 1/8W C801 C802 C803 C804 C805 1-110-454-11 1-110-454-11 1-164-004-11 1-164-004-11 1-104-851-11 SOLID CHIP SOLID CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP 10uF 10uF 0.1uF 0.1uF 10uF 20% 20% 10% 10% 20% 16V 16V 25V 25V 10V R1326 R1327 R1401 R1402 R1403 1-216-001-00 1-216-073-00 1-216-025-00 1-260-032-11 1-259-991-11 METAL CHIP METAL CHIP METAL CHIP CARBON MELF CARBON MELF 10 10K 100 1M 470 5% 5% 5% 2% 2% 1/10W 1/10W 1/10W 1/8W 1/8W C806 C808 C809 C810 C901 1-164-004-11 1-126-613-11 1-126-613-11 1-115-339-11 1-110-449-11 CERAMIC CHIP ELECT ELECT CERAMIC CHIP SOLID CHIP 0.1uF 10uF 10uF 0.1uF 47uF 10% 20% 20% 10% 20% 25V 50V 50V 50V 6.3V R1404 R1601 R1602 R1605 R1606 1-216-001-00 1-260-016-11 1-260-016-11 1-260-020-11 1-216-222-00 METAL CHIP CARBON MELF CARBON MELF CARBON MELF METAL CHIP 10 47K 47K 100K 10K 5% 2% 2% 2% 0.5% 1/10W 1/8W 1/8W 1/8W 1/8W C902 C903 C904 C905 C906 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-162-927-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 100PF 10% 10% 10% 10% 5% 16V 16V 16V 16V 50V R1607 R1608 R1609 R1610 R1611 1-208-810-11 1-208-810-11 1-216-222-00 1-216-222-00 1-208-810-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 15K 15K 10K 10K 15K 0.5% 0.5% 0.5% 0.5% 0.5% 1/8W 1/8W 1/8W 1/8W 1/8W C921 C931 C932 C933 C941 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-162-964-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.001uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 50V R1612 R1613 R1614 R1615 R1616 1-208-810-11 1-216-222-00 1-260-004-11 1-260-004-11 1-260-004-11 METAL CHIP METAL CHIP CARBON MELF CARBON MELF CARBON MELF 15K 10K 4.7K 4.7K 4.7K 0.5% 0.5% 2% 2% 2% 1/8W 1/8W 1/8W 1/8W 1/8W C942 C943 C944 C945 C951 1-107-826-11 1-107-826-11 1-162-964-11 1-107-826-11 1-107-826-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.001uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 16V 16V 50V 16V 16V R1617 R1618 R1620 R1622 R1624 1-260-004-11 1-260-004-11 1-260-004-11 1-260-004-11 1-260-004-11 CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF 4.7K 4.7K 4.7K 4.7K 4.7K 2% 2% 2% 2% 2% 1/8W 1/8W 1/8W 1/8W 1/8W C980 C981 C982 1-113-500-11 TANTAL. CHIP 1-107-826-11 CERAMIC CHIP 1-113-987-11 TANTAL. CHIP 100uF 0.1uF 4.7uF 20% 10V 10% 16V 20% 25V R1626 R1627 R1628 R1629 R1630 1-216-001-00 1-259-983-11 1-259-983-11 1-259-983-11 1-259-983-11 METAL CHIP CARBON MELF CARBON MELF CARBON MELF CARBON MELF 10 100 100 100 100 5% 2% 2% 2% 2% 1/10W 1/8W 1/8W 1/8W 1/8W CN901 * CN902 * CN903 R1631 R1632 R1633 1-216-049-00 METAL CHIP 1-259-995-11 CARBON MELF 1-259-995-11 CARBON MELF 1K 1K 1K 5% 2% 2% 1/10W 1/8W 1/8W D801 D802 D811 D941 D942 8-719-048-98 8-719-018-10 8-719-052-12 8-719-422-64 8-719-422-64 D943 D944 8-719-422-64 DIODE MA8062-M 8-719-422-64 DIODE MA8062-M < RELAY > RY1101 1-755-188-11 RELAY RY1201 1-755-188-11 RELAY RY1301 1-755-188-11 RELAY RY1601 1-755-188-11 RELAY RY1602 1-755-188-11 RELAY RY1603 1-755-188-11 RELAY < VIBRATOR > X1401 1-767-338-11 VIBRATOR, CRYSTAL (11.2896MHz) ************************************************************ A-3309-673-A DISPLAY BOARD, COMPLETE ************************ * < BUZZER > 1-505-263-21 BUZZER < CAPACITOR > < CONNECTOR > 1-774-945-11 PLUG, CONNECTOR 14P 1-750-161-21 CONNECTOR, FPC 30P 1-750-248-21 CONNECTOR, FPC 5P < DIODE > – 188 – DIODE DIODE DIODE DIODE DIODE RB160L-40TE25 MA8300-TX 1SS376TE-17 MA8062-M MA8062-M DISPLAY Ref. No. D945 Part No. Part No. Description R915 R916 R917 R918 R919 1-216-809-11 1-216-821-11 1-216-809-11 1-216-817-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 1K 100 470 100K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W < IC > R920 R921 R922 R923 R931 1-216-845-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100 100 100 100K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W IC IC IC IC IC R932 R933 R941 R942 R943 1-216-845-11 1-216-845-11 1-216-809-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 100 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R944 R947 R951 R952 R953 1-216-809-11 1-216-809-11 1-216-845-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100K 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R980 R981 1-216-841-11 METAL CHIP 1-216-819-11 METAL CHIP 47K 680 5% 5% 1/16W 1/16W Description Remark Ref. No. 8-719-422-64 DIODE MA8062-M < FERRITE BEAD > FB801 FB901 FB931 FB932 FB941 1-414-233-21 1-414-234-11 1-414-234-11 1-414-234-11 1-414-234-11 INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD IC801 IC901 IC921 IC931 IC932 8-759-521-35 8-759-443-23 8-759-079-52 8-759-486-71 8-752-376-15 IC941 IC942 IC951 8-759-079-56 IC TC74VHC14FS (EL) 8-759-439-67 IC TC7W126FU (TE12R) 8-759-079-60 IC TC74VHC32FS (EL) TL5001CD HD6473048-DISP01 TC74VHC08FS (EL) MBM29F800-DISPU CXK516100TM-70LL-TL < COIL > L801 L802 L901 DOE 1-410-381-11 INDUCTOR CHIP 10uH 1-414-449-11 INDUCTOR 100uH 1-410-381-11 INDUCTOR CHIP 10uH Remark < NETWORK RESISTOR > < TRANSISTOR > Q801 Q802 Q803 Q811 Q901 8-729-023-85 8-729-011-57 8-729-021-94 8-729-900-53 8-729-900-53 FET FET FET TRANSISTOR TRANSISTOR 2SJ168 2SK1880S-TL 2SK1657-T1B DTC114EK DTC114EK < RESISTOR/CHIP CONDUCTOR > R202 R701 R801 R802 R803 1-216-845-11 1-216-832-11 1-216-091-00 1-216-089-00 1-216-295-00 METAL CHIP 100K METAL CHIP 8.2K METAL CHIP 56K METAL CHIP 47K CONDUCTOR, CHIP (2012) 5% 5% 5% 5% 1/16W 1/16W 1/10W 1/10W R804 R805 R806 R807 R808 1-216-037-00 1-216-691-11 1-216-659-11 1-216-829-11 1-216-680-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 330 47K 2.2K 4.7K 16K 5% 0.5% 0.5% 5% 0.5% 1/10W 1/10W 1/10W 1/16W 1/10W R809 R811 R812 R821 R830 1-216-009-00 1-216-009-00 1-216-009-00 1-216-009-00 1-216-817-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22 22 22 22 470 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/16W R901 R902 R903 R904 R905 1-216-829-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 4.7K 0 0 0 0 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R906 R907 R908 R910 R911 1-216-809-11 1-216-809-11 1-216-829-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 4.7K 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R912 R914 1-216-809-11 METAL CHIP 1-216-832-11 METAL CHIP 100 8.2K 5% 5% 1/16W 1/16W RB901 RB902 RB903 RB904 RB905 1-233-576-11 1-233-576-11 1-216-182-00 1-216-182-00 1-233-576-11 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 100×4 RB906 RB907 RB908 RB909 RB910 1-233-576-11 1-233-576-11 1-233-576-11 1-233-576-11 1-233-576-11 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RB931 RB932 RB933 RB934 RB935 1-216-182-00 1-233-576-11 1-216-182-00 1-233-576-11 1-233-576-11 RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RB936 RB937 RB938 1-233-576-11 RES, CHIP NETWORK 100×4 1-233-576-11 RES, CHIP NETWORK 100×4 1-233-576-11 RES, CHIP NETWORK 100×4 < VARIABLE RESISTOR > RV801 1-238-089-11 RES, ADJ, CERMET 4.7K < VIBRATOR > X901 1-767-426-21 VIBRATOR, CERAMIC (14.745MHz) ************************************************************ 1-664-113-12 DOE BOARD ********** * < CONNECTOR > CNJ703 1-774-792-21 CONNECTOR, FPC/FFC 4P – 189 – DOE Ref. No. DPT Part No. DRIVER Description Remark Ref. No. Part No. Description Remark CNJ203 1-778-775-21 CONNECTOR, FPC 13P < DIODE > D702 8-719-045-93 LED AN1102W-1-TR (DOE) ************************************************************ CNJ204 1-778-815-21 CONNECTOR, FPC 8P < IC > 1-664-112-12 DPT BOARD ********** * < DIODE > D703 8-719-045-93 LED AN1102W-1-TR (DPT) ************************************************************ IC101 IC201 IC202 IC251 IC252 8-752-069-93 8-759-070-68 8-759-071-79 8-759-159-54 8-759-927-72 IC253 8-759-981-69 IC LM2904M A-3309-668-A DRIVER BOARD, COMPLETE *********************** * IC IC IC IC IC CXA1791M-T6 BA6247FP-Y BA6297AFP NJU7104AM TL1591CP < COIL > L101 < CAPACITOR > 1-412-058-11 INDUCTOR CHIP 10uH < PHOTO INTERRUPTER > C101 C102 C103 C104 C105 1-135-227-11 1-163-243-11 1-110-569-11 1-110-569-11 1-164-004-11 TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP 100uF 47PF 47uF 47uF 0.1uF 20% 5% 20% 20% 10% 6.3V 50V 6.3V 6.3V 25V C106 C107 C111 C200 C201 1-104-823-11 1-104-823-11 1-164-004-11 1-104-823-11 1-164-004-11 TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP 47uF 47uF 0.1uF 47uF 0.1uF 20% 20% 10% 20% 10% 16V 16V 25V 16V 25V Q101 Q103 Q252 C202 C203 C204 C205 C221 1-164-004-11 1-164-004-11 1-104-914-11 1-164-004-11 1-163-251-11 CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 22uF 0.1uF 100PF 10% 10% 20% 10% 5% 25V 25V 16V 25V 50V R101 R102 R103 R104 R105 1-216-093-00 1-216-093-00 1-216-093-00 1-216-093-00 1-216-093-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 68K 68K 68K 68K 68K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C222 C223 C224 C225 C226 1-163-251-11 1-163-121-00 1-163-017-00 1-163-121-00 1-163-017-00 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100PF 150PF 0.0047uF 150PF 0.0047uF 5% 5% 10% 5% 10% 50V 50V 50V 50V 50V R106 R107 R111 R112 R113 1-216-093-00 1-216-024-00 1-216-061-00 1-216-061-00 1-216-061-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 68K 91 3.3K 3.3K 3.3K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C227 C228 C229 C230 C231 1-164-004-11 1-164-004-11 1-104-823-11 1-163-009-11 1-104-823-11 CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP 0.1uF 0.1uF 47uF 0.001uF 47uF 10% 10% 20% 10% 20% 25V 25V 16V 50V 16V R114 R115 R116 R117 R118 1-216-073-00 1-216-073-00 1-216-073-00 1-216-009-00 1-216-073-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 10K 22 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C232 C233 C234 C235 C251 1-163-121-00 1-163-121-00 1-110-501-11 1-163-125-00 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 150PF 150PF 0.33uF 220PF 0.1uF 5% 5% 10% 5% 10% 50V 50V 16V 50V 25V R119 R201 R202 R203 R221 1-216-041-00 1-216-049-00 1-216-049-00 1-216-049-00 1-216-081-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470 1K 1K 1K 22K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C252 C253 C254 C255 C256 1-164-004-11 1-164-161-11 1-107-823-11 1-164-004-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.0022uF 0.47uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 25V 100V 16V 25V 25V R222 R223 R224 R225 R226 1-216-081-00 1-216-081-00 1-216-081-00 1-216-081-00 1-216-073-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22K 22K 22K 22K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C257 C258 C259 1-164-004-11 CERAMIC CHIP 1-164-004-11 CERAMIC CHIP 1-135-227-11 TANTAL. CHIP 0.1uF 0.1uF 100uF 10% 25V 10% 25V 20% 6.3V < CONNECTOR > R227 R228 R229 R230 R231 1-216-081-00 1-216-073-00 1-216-085-00 1-216-085-00 1-216-085-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22K 10K 33K 33K 33K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W CONNECTOR, FPC 12P CONNECTOR, FPC 22P CONNECTOR, FFC/FPC (ZIF) 6P CONNECTOR, FPC 12P R232 R233 R235 R236 1-216-085-00 1-216-089-00 1-216-308-00 1-216-085-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 33K 47K 4.7 33K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W CNJ101 CNJ102 CNJ201 CNJ202 1-766-767-21 1-778-817-21 1-764-621-21 1-766-767-21 PH101 8-749-925-02 PHOTO INTERRUPTER SG-223 < TRANSISTOR > 8-729-141-48 TRANSISTOR 2SB624-BV345 8-729-027-31 TRANSISTOR DTA124EKA-T146 8-729-820-68 TRANSISTOR 2SD1802FA-S < RESISTOR > – 190 – DRIVER Ref. No. Part No. Description Remark Ref. No. Part No. DSP Description Remark R237 1-216-085-00 METAL CHIP 33K 5% 1/10W C205 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V R238 R239 R240 R241 R251 1-216-073-00 1-216-073-00 1-216-093-00 1-216-093-00 1-216-073-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 68K 68K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C206 C207 C208 C209 C210 1-164-004-11 1-164-004-11 1-164-004-11 1-164-004-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% R252 R253 R255 R256 R257 1-216-073-00 1-216-073-00 1-216-073-00 1-216-085-00 1-216-085-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 10K 33K 33K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C211 C212 C213 C214 C215 1-164-004-11 1-164-004-11 1-164-232-11 1-104-851-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP 0.1uF 0.1uF 0.01uF 10uF 0.1uF 10% 25V 10% 25V 50V 20% 10V 10% 25V R258 R261 R262 R263 R264 1-216-073-00 1-216-093-00 1-216-093-00 1-216-093-00 1-216-069-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 68K 68K 68K 6.8K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C216 C217 C301 C302 C303 1-164-004-11 1-164-004-11 1-104-851-11 1-164-232-11 1-164-232-11 CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 10uF 0.01uF 0.01uF 10% 25V 10% 25V 20% 10V 50V 50V R265 R267 R268 R269 1-216-085-00 1-216-001-00 1-216-001-00 1-216-037-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 33K 10 10 330 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W C304 C305 C311 C312 C316 1-164-232-11 1-164-232-11 1-164-004-11 1-163-009-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.01uF 0.1uF 0.001uF 0.1uF 50V 50V 10% 25V 10% 50V 10% 25V C371 C381 C382 C383 C391 1-164-232-11 1-164-232-11 1-163-009-11 1-164-232-11 1-163-017-00 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 50V 0.01uF 50V 0.001uF 10% 50V 0.01uF 50V 0.0047uF 5% 50V C392 C393 C401 C402 C403 1-163-009-11 1-104-851-11 1-104-851-11 1-164-232-11 1-164-232-11 CERAMIC CHIP TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 10uF 10uF 0.01uF 0.01uF 10% 50V 20% 10V 20% 10V 50V 50V C404 C405 C411 C412 C413 1-164-232-11 1-164-232-11 1-104-851-11 1-164-004-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.01uF 10uF 0.1uF 0.1uF 50V 50V 20% 10V 10% 25V 10% 25V C414 C415 C416 C417 C418 1-164-004-11 1-164-004-11 1-164-004-11 1-164-004-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 25V 25V 25V 25V 25V C421 C501 C502 C503 C504 1-164-004-11 1-164-004-11 1-104-851-11 1-164-004-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 10uF 0.1uF 0.1uF 10% 10% 20% 10% 10% 25V 25V 10V 25V 25V C505 C506 C507 C508 C509 1-164-004-11 1-104-851-11 1-164-004-11 1-163-809-11 1-104-851-11 CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP 0.1uF 10uF 0.1uF 0.047uF 10uF 10% 20% 10% 10% 20% 25V 10V 25V 25V 10V C510 C601 C605 C606 C607 1-164-004-11 1-104-851-11 1-164-232-11 1-164-004-11 1-163-009-11 CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 10uF 0.01uF 0.1uF 0.001uF 10% 25V 20% 10V 50V 10% 25V 10% 50V C608 C609 1-164-232-11 CERAMIC CHIP 1-164-232-11 CERAMIC CHIP 25V 25V 25V 25V 25V < VARIABLE RESISTOR > RV101 1-238-091-11 RES, ADJ, CERMET 22K RV102 1-238-091-11 RES, ADJ, CERMET 22K ************************************************************ A-3309-657-A DSP BOARD, COMPLETE ******************** * 3-008-595-01 3-009-031-01 3-014-157-01 3-014-158-01 7-685-146-11 * * * * CASE (DSP PC BOARD), SHIELD COVER (CONNECTOR) SPACER (DD CONVERTER A) SPACER (DD CONVERTER B) SCREW +P 3×8 TYPE2 NON-SLIT < CAPACITOR > C101 C102 C103 C104 C105 1-104-851-11 1-164-004-11 1-164-004-11 1-163-009-11 1-164-004-11 TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 0.1uF 0.1uF 0.001uF 0.1uF 20% 10% 10% 10% 10% 10V 25V 25V 50V 25V C106 C107 C108 C109 C110 1-164-004-11 1-164-004-11 1-164-004-11 1-164-004-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 25V 25V 25V 25V 25V C111 C112 C114 C115 C116 1-164-004-11 1-164-004-11 1-104-851-11 1-164-004-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 10uF 0.1uF 0.1uF 10% 10% 20% 10% 10% 25V 25V 10V 25V 25V C117 C119 C120 C131 C132 1-164-004-11 1-164-232-11 1-164-232-11 1-164-004-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.01uF 0.01uF 0.1uF 0.1uF 10% 25V 50V 50V 10% 25V 10% 25V C201 C202 C203 C204 1-104-851-11 1-164-004-11 1-164-004-11 1-163-009-11 TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 0.1uF 0.1uF 0.001uF 20% 10% 10% 10% 10V 25V 25V 50V – 191 – 0.01uF 0.01uF 50V 50V DSP Ref. No. Part No. Description Remark C610 C611 C612 1-164-232-11 CERAMIC CHIP 1-104-851-11 TANTAL. CHIP 1-104-851-11 TANTAL. CHIP 0.01uF 10uF 10uF 50V 20% 10V 20% 10V C613 C621 C702 C703 C704 1-164-004-11 1-164-232-11 1-104-851-11 1-104-851-11 1-104-851-11 CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP TANTAL. CHIP TANTAL. CHIP 0.1uF 0.01uF 10uF 10uF 10uF 10% 25V 50V 20% 10V 20% 10V 20% 10V C705 C706 C707 C710 C802 1-104-851-11 1-164-004-11 1-163-009-11 1-164-004-11 1-136-165-00 TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP FILM 10uF 0.1uF 0.001uF 0.1uF 0.1uF 20% 10% 10% 10% 5% 10V 25V 50V 25V 50V C803 C804 C805 C811 C812 1-163-009-11 1-104-539-11 1-104-559-11 1-124-704-11 1-136-960-11 CERAMIC CHIP FILM FILM ELECT FILM 0.001uF 0.001uF 0.047uF 3300uF 0.1uF 10% 5% 5% 20% 10% 50V 50V 16V 25V 160V C814 C821 C822 C831 C832 1-126-964-11 1-124-689-11 1-136-165-00 1-126-013-11 1-136-165-00 ELECT ELECT FILM ELECT FILM 10uF 1000uF 0.1uF 1000uF 0.1uF 20% 20% 5% 20% 5% 50V 16V 50V 16V 50V C841 C842 C843 C844 C846 1-126-013-11 1-136-165-00 1-126-933-11 1-124-599-11 1-128-222-11 ELECT FILM ELECT ELECT ELECT 1000uF 0.1uF 100uF 220uF 330uF 20% 5% 20% 20% 20% 16V 50V 16V 25V 16V C847 C851 C852 C853 C854 1-164-004-11 1-164-004-11 1-126-933-11 1-164-004-11 1-126-964-11 CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT 0.1uF 0.1uF 100uF 0.1uF 10uF 10% 10% 20% 10% 20% 25V 25V 16V 25V 50V C855 C856 C858 C859 C860 1-126-933-11 1-125-710-11 1-164-004-11 1-164-004-11 1-126-933-11 ELECT DOUBLE LAYER CERAMIC CHIP CERAMIC CHIP ELECT 100uF 0.1F 0.1uF 0.1uF 100uF 20% 16V 5.5V 10% 25V 10% 25V 20% 16V C861 C862 C863 C864 C865 1-164-004-11 1-164-004-11 1-126-933-11 1-164-004-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 100uF 0.1uF 0.1uF 10% 10% 20% 10% 10% 25V 25V 16V 25V 25V C866 C867 C901 C902 C903 1-126-933-11 1-126-163-11 1-104-551-11 1-104-551-11 1-164-004-11 ELECT ELECT FILM FILM CERAMIC CHIP 100uF 4.7uF 0.01uF 0.01uF 0.1uF 20% 20% 5% 5% 10% 16V 50V 50V 50V 25V Ref. No. CN34 CN41 * CN42 Part No. Description 1-506-945-11 PIN, CONNECTOR 3P 1-778-939-11 CONNECTOR, FFC/FPC (ZIF) 30P 1-766-324-11 CONNECTOR, FFC/FPC (ZIF) 8P < DIODE > D391 D392 D393 D395 D396 8-719-975-40 8-719-975-40 8-719-404-49 8-719-404-49 8-719-404-49 DIODE DIODE DIODE DIODE DIODE RB411D RB411D MA111 MA111 MA111 D701 D702 D703 D704 D705 8-719-404-49 8-719-404-49 8-719-422-64 8-719-422-64 8-719-422-64 DIODE DIODE DIODE DIODE DIODE MA111 MA111 MA8062-M MA8062-M MA8062-M D706 D707 D708 D709 D710 8-719-422-64 8-719-422-64 8-719-422-64 8-719-422-64 8-719-422-64 DIODE DIODE DIODE DIODE DIODE MA8062-M MA8062-M MA8062-M MA8062-M MA8062-M D711 D801 D802 D803 D804 8-719-422-64 8-719-061-72 8-719-210-33 8-719-404-49 8-719-422-64 DIODE DIODE DIODE DIODE DIODE MA8062-M ERB81-004K EC10DS2 MA111 MA8062-M D805 D806 D807 D841 D842 8-719-975-40 8-719-404-49 8-719-976-99 8-719-048-98 8-719-812-41 DIODE DIODE DIODE DIODE LED RB411D MA111 DTZ5.1B RB160L-40TE25 TLR124 D843 D904 D905 D906 D907 8-719-404-49 8-719-422-64 8-719-422-64 8-719-422-64 8-719-422-64 DIODE DIODE DIODE DIODE DIODE MA111 MA8062-M MA8062-M MA8062-M MA8062-M D908 D909 D910 D911 8-719-422-64 8-719-422-64 8-719-422-64 8-719-422-64 DIODE DIODE DIODE DIODE MA8062-M MA8062-M MA8062-M MA8062-M < FERRITE BEAD > < TERMINAL/CONNECTOR/IC > CN11 CN12 CN13 CN14 CN21 1-537-477-11 1-778-830-11 1-580-907-31 8-749-923-62 1-506-947-11 TERMINAL BOARD (3P) (POWER) CONNECTOR (BUS) (MASTER BUS CONTROL) PLUG, CONNECTOR (SONY BUS CONTROL) IC TORX-193 (DIGITAL IN AUX AUDIO) PIN, CONNECTOR 6P CN22 CN31 CN32 CN33 1-779-121-11 1-779-119-11 1-779-118-11 1-779-068-21 PIN, CONNECTOR 12P PIN, CONNECTOR 5P PIN, CONNECTOR 4P PIN, CONNECTOR 5P FB101 FB102 FB103 FB104 FB105 1-414-235-11 1-414-235-11 1-414-235-11 1-414-235-11 1-414-235-11 INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD FB106 FB107 FB108 FB109 FB110 1-414-235-11 1-414-235-11 1-414-235-11 1-414-235-11 1-414-235-11 INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD FB121 FB131 FB201 FB202 FB203 1-414-235-11 1-414-235-11 1-414-235-11 1-414-235-11 1-414-235-11 INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD FB204 FB205 FB206 1-414-235-11 INDUCTOR, FERRITE BEAD 1-414-235-11 INDUCTOR, FERRITE BEAD 1-414-235-11 INDUCTOR, FERRITE BEAD – 192 – Remark DSP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark FB207 FB208 1-414-235-11 INDUCTOR, FERRITE BEAD 1-414-235-11 INDUCTOR, FERRITE BEAD FB209 FB210 FB221 FB301 FB401 1-414-235-11 1-414-235-11 1-414-235-11 1-414-235-11 1-414-235-11 INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD L301 L501 L502 L601 L603 1-412-058-11 1-412-062-11 1-412-060-11 1-412-060-11 1-412-058-11 INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP FB402 FB403 FB404 FB501 FB502 1-414-235-11 1-414-235-11 1-414-235-11 1-414-235-11 1-414-235-11 INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD L604 L801 L802 L803 L804 1-412-058-11 1-406-723-11 1-406-723-11 1-415-937-11 1-412-055-11 INDUCTOR CHIP 10uH COIL, CHOKE (TROIDAL) 700uH COIL, CHOKE (TROIDAL) 700uH COIL, CHOKE 125uH INDUCTOR CHIP 3.3uH FB623 FB701 FB702 FB703 FB704 1-414-235-11 1-414-235-11 1-414-235-11 1-414-235-11 1-414-235-11 INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD L841 L843 L844 1-416-040-11 COIL, CHOKE 220uH 1-412-055-11 INDUCTOR CHIP 3.3uH 1-412-058-11 INDUCTOR CHIP 10uH FB705 1-414-235-11 INDUCTOR, FERRITE BEAD Q392 Q393 Q502 Q503 Q801 8-729-424-08 8-729-424-08 8-729-904-60 8-729-421-19 8-729-230-49 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR UN2111 UN2111 DTB113ZK UN2213 2SC2712-YG Q802 Q803 Q804 Q871 Q872 8-729-040-17 8-729-025-88 8-729-421-22 8-729-822-84 8-729-421-22 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SD2164-K 2SB1386-T100-R UN2211 2SB1202FAST UN2211 < FUSE TERMINAL > FF1 FF2 1-537-479-21 TERMINAL, FUSE 1-537-479-21 TERMINAL, FUSE < IC > IC101 IC102 IC103 IC105 IC201 8-752-379-58 8-759-364-50 8-759-096-87 8-759-443-28 8-752-379-58 IC IC IC IC IC CXD2711Q HM51W4260CLTT-7 TC7WU04FU (TE12R) 74LVXC4245QSCX CXD2711Q IC202 IC301 IC302 IC303 IC304 8-759-364-50 8-759-443-32 8-759-443-04 8-759-326-78 8-759-443-28 IC IC IC IC IC HM51W4260CLTT-7 HD6473048-DSP01 AT24C32N-10SI-TR PST9140NL 74LVXC4245QSCX IC305 IC306 IC401 IC402 IC411 8-759-277-63 8-759-284-87 8-759-486-69 8-759-486-70 8-759-079-60 IC IC IC IC IC TC7W14FU (TE12R) MM1284XFFE MBM29F016-90PFTN-DSP02L MBM29F016-90PFTN-DSP02H TC74VHC32FS (EL) IC412 IC413 IC414 IC415 IC416 8-759-079-46 8-759-079-67 8-759-079-49 8-759-080-08 8-759-079-67 IC IC IC IC IC TC74VHC00FS (EL) TC74VHC125FS (EL) TC74VHC04FS (EL) TC74VHC595FS (EL) TC74VHC125FS (EL) IC417 IC418 IC502 IC503 IC601 8-759-079-67 8-759-080-02 8-759-164-46 8-759-082-57 8-752-372-30 IC IC IC IC IC TC74VHC125FS (EL) TC74VHC541FS (EL) CS8412-IS-E1 TC7W04FU CXD2710R IC602 IC603 IC701 IC702 IC703 8-759-096-87 8-759-080-02 8-759-079-67 8-759-443-25 8-759-443-25 IC IC IC IC IC TC7WU04FU (TE12R) TC74VHC541FS (EL) TC74VHC125FS (EL) IS0150AU IS0150AU IC801 IC802 IC803 IC804 8-759-701-59 8-759-335-72 8-759-443-30 8-759-443-24 IC IC IC IC NJM78M09FA uPC24A05HF MC33269DTRK-3.3 SAI01-V1 < COIL > 10uH 47uH 22uH 22uH 10uH < TRANSISTOR > < RESISTOR/CHIP CONDUCTOR > R101 R110 R111 R112 R113 1-216-805-11 1-216-845-11 1-216-813-11 1-216-025-00 1-216-025-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47 100K 220 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/10W 1/10W R130 R134 R135 R136 R137 1-216-811-11 1-216-033-00 1-216-033-00 1-216-033-00 1-216-033-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 150 220 220 220 220 5% 5% 5% 5% 5% 1/16W 1/10W 1/10W 1/10W 1/10W R138 R146 R149 R150 R151 1-216-033-00 1-216-809-11 1-216-811-11 1-216-811-11 1-216-811-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 220 100 150 150 150 5% 5% 5% 5% 5% 1/10W 1/16W 1/16W 1/16W 1/16W R152 R153 R178 R179 R180 1-216-845-11 1-216-845-11 1-216-813-11 1-216-857-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 220 1M 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R181 R201 R210 R211 R212 1-216-295-00 1-216-805-11 1-216-845-11 1-216-845-11 1-216-025-00 CONDUCTOR, CHIP (2012) METAL CHIP 47 METAL CHIP 100K METAL CHIP 100K METAL CHIP 100 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/10W R230 R246 R249 R250 R251 1-216-811-11 1-216-809-11 1-216-811-11 1-216-811-11 1-216-811-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W – 193 – 150 100 150 150 150 DSP Ref. No. Part No. Description R252 R253 R301 R302 R303 1-216-845-11 1-216-845-11 1-216-025-00 1-216-025-00 1-216-025-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP R304 R305 R306 R307 R308 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 1-216-295-00 R309 R310 R311 R321 R322 Remark 100K 100K 100 100 100 Ref. No. Part No. Description Remark R404 R411 R412 R413 R414 1-216-089-00 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47K 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R415 R417 R421 R423 R424 1-216-025-00 1-216-025-00 1-216-097-00 1-216-017-00 1-216-025-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100K 47 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R425 R431 R432 R433 R434 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R435 R441 R442 R443 R444 1-216-025-00 1-216-025-00 1-216-097-00 1-216-025-00 1-216-025-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100K 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R445 R446 R447 R448 R450 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 1-216-073-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R451 R452 R461 R462 1-216-025-00 1-216-097-00 1-216-025-00 1-216-097-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100K 100 100K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1-216-025-00 1-216-097-00 1-216-809-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100K 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/16W 1/16W 1/16W 5% 5% 5% 5% 5% 1/16W 1/16W 1/10W 1/10W 1/10W METAL CHIP 100 METAL CHIP 100 METAL CHIP 100 METAL CHIP 100 CONDUCTOR, CHIP (2012) 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1-216-025-00 1-216-025-00 1-216-295-00 1-216-025-00 1-216-041-00 METAL CHIP 100 METAL CHIP 100 CONDUCTOR, CHIP (2012) METAL CHIP 100 METAL CHIP 470 5% 5% 1/10W 1/10W 5% 5% 1/10W 1/10W R323 R324 R325 R326 R327 1-216-041-00 1-216-295-00 1-216-025-00 1-216-025-00 1-216-025-00 METAL CHIP 470 CONDUCTOR, CHIP (2012) METAL CHIP 100 METAL CHIP 100 METAL CHIP 100 5% 1/10W 5% 5% 5% 1/10W 1/10W 1/10W R328 R329 R330 R331 R333 1-216-295-00 1-216-049-00 1-216-049-00 1-216-045-00 1-216-097-00 CONDUCTOR, CHIP (2012) METAL CHIP 1K METAL CHIP 1K METAL CHIP 680 METAL CHIP 100K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R334 R335 R341 R342 R345 1-216-097-00 1-216-097-00 1-216-295-00 1-216-295-00 1-216-295-00 METAL CHIP 100K METAL CHIP 100K CONDUCTOR, CHIP (2012) CONDUCTOR, CHIP (2012) CONDUCTOR, CHIP (2012) 5% 5% 1/10W 1/10W R348 R349 R351 R352 R353 1-216-097-00 1-216-295-00 1-216-025-00 1-216-025-00 1-216-025-00 METAL CHIP 100K CONDUCTOR, CHIP (2012) METAL CHIP 100 METAL CHIP 100 METAL CHIP 100 5% 1/10W 5% 5% 5% 1/10W 1/10W 1/10W R463 R464 R471 R472 R473 R355 R356 R357 R359 R360 1-216-097-00 1-216-097-00 1-216-097-00 1-216-073-00 1-216-025-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 100K 10K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R474 R475 R476 R501 R502 1-216-809-11 1-216-809-11 1-216-809-11 1-216-025-00 1-216-025-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/10W 1/10W R361 R362 R363 R364 R365 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R503 R504 R505 R506 R507 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 1-216-049-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R366 R368 R370 R371 R381 1-216-025-00 1-216-097-00 1-216-097-00 1-216-089-00 1-216-073-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100K 100K 47K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R508 R509 R510 R601 R603 1-216-041-00 1-216-025-00 1-216-025-00 1-216-001-00 1-216-097-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470 100 100 10 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R382 R384 R385 R391 R392 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R605 R606 R607 R608 R609 1-216-097-00 1-216-041-00 1-216-041-00 1-216-041-00 1-216-041-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 470 470 470 470 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R393 R394 R395 R401 R403 1-216-025-00 1-216-025-00 1-216-089-00 1-216-097-00 1-216-097-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 47K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R610 R612 R613 R614 1-216-041-00 1-216-025-00 1-216-025-00 1-216-025-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470 100 100 100 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W – 194 – DSP Ref. No. Part No. Description Remark R615 1-216-025-00 METAL CHIP 100 5% 1/10W R616 R621 R623 R624 R631 1-216-025-00 1-216-121-00 1-216-025-00 1-216-295-00 1-216-097-00 METAL CHIP 100 METAL CHIP 1M METAL CHIP 100 CONDUCTOR, CHIP (2012) METAL CHIP 100K 5% 5% 5% 1/10W 1/10W 1/10W 5% 1/10W R634 R701 R702 R703 R704 1-216-045-00 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 680 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R705 R706 R707 R708 R711 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R712 R713 R714 R715 R802 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 1-216-089-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R803 R804 R806 R807 R808 1-216-689-11 1-216-105-00 1-216-077-00 1-216-089-00 1-216-065-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 39K 220K 15K 47K 4.7K 0.5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R809 R810 R811 R841 R842 1-216-065-00 1-216-065-00 1-216-065-00 1-216-049-00 1-216-065-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 4.7K 4.7K 4.7K 1K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R843 R844 R845 R873 R874 1-216-049-00 1-216-049-00 1-216-049-00 1-216-073-00 1-216-065-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 1K 10K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R875 R901 R902 R921 R922 1-216-065-00 1-216-017-00 1-216-017-00 1-216-097-00 1-216-097-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 4.7K 47 47 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R923 1-216-097-00 METAL CHIP 100K 5% 1/10W Ref. No. RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RB106 RB107 RB108 RB201 RB202 1-233-576-11 1-233-576-11 1-233-576-11 1-233-576-11 1-233-576-11 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RB203 RB204 RB205 1-233-576-11 RES, CHIP NETWORK 100×4 1-233-576-11 RES, CHIP NETWORK 100×4 1-233-576-11 RES, CHIP NETWORK 100×4 Description 1-233-576-11 RES, CHIP NETWORK 100×4 1-233-576-11 RES, CHIP NETWORK 100×4 RB208 RB301 RB302 RB303 RB304 1-233-576-11 1-233-576-11 1-233-576-11 1-233-576-11 1-233-576-11 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RB305 RB306 RB307 RB308 RB309 1-233-576-11 1-233-576-11 1-233-576-11 1-233-576-11 1-233-576-11 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RB311 RB312 RB313 RB314 RB315 1-233-810-21 1-233-810-21 1-233-810-21 1-233-810-21 1-233-810-21 RES, NETWORK 100K×4 (3216) RES, NETWORK 100K×4 (3216) RES, NETWORK 100K×4 (3216) RES, NETWORK 100K×4 (3216) RES, NETWORK 100K×4 (3216) RB316 RB317 RB318 RB319 RB381 1-233-810-21 1-233-810-21 1-233-810-21 1-233-810-21 1-233-576-11 RES, NETWORK 100K×4 (3216) RES, NETWORK 100K×4 (3216) RES, NETWORK 100K×4 (3216) RES, NETWORK 100K×4 (3216) RES, CHIP NETWORK 100×4 RB382 RB383 RB384 RB401 RB402 1-233-576-11 1-233-576-11 1-233-576-11 1-216-182-00 1-216-182-00 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 100×4 RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 220×4 (3216) RB403 RB404 1-216-182-00 RES, CHIP NETWORK 220×4 (3216) 1-216-182-00 RES, CHIP NETWORK 220×4 (3216) Remark < THERMISTOR > TH872 1-810-940-11 THERMISTOR, POSITIVE < VARISTOR > VDR801 1-806-500-11 VARISTOR < VIBRATOR > X101 1-767-382-11 VIBRATOR, CERAMIC (40.0MHz) X301 1-767-426-21 VIBRATOR, CERAMIC (14.74MHz) X601 1-767-427-21 VIBRATOR, CERAMIC (18.43MHz) ************************************************************ 1-664-114-12 EJT BOARD ********* * 1-233-576-11 1-233-576-11 1-233-576-11 1-233-576-11 1-233-576-11 LINE IN RB206 RB207 < NETWORK RESISTOR > RB101 RB102 RB103 RB104 RB105 Part No. EJT < CONNECTOR > CNP11 1-580-057-11 PIN, CONNECTOR 4P < SWITCH > SW11 SW12 1-762-737-11 SWITCH, KEYBOARD (LED) (6) 1-692-072-11 SWITCH, PUSH (1 KEY) (DOOR OPEN/CLOSE DET) ************************************************************ * 1-664-165-12 LINE IN BOARD ************* < CONNECTOR > – 195 – LINE IN Ref. No. LINE OUT Part No. MAIN Description Remark CN2011 1-779-118-11 PIN, CONNECTOR 4P < PIN JACK > JK2011 1-573-057-21 JACK, PIN 1P (ANALOG IN AUX AUDIO L) JK2012 1-573-057-31 JACK, PIN 1P (ANALOG IN AUX AUDIO R) ************************************************************ 1-664-164-12 LINE OUT BOARD ************** * Ref. No. Part No. Description Remark C532 C533 C534 C535 C536 1-164-232-11 1-164-232-11 1-164-004-11 1-164-004-11 1-126-177-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT 0.01uF 0.01uF 0.1uF 0.1uF 100uF 50V 50V 10% 25V 10% 25V 20% 10V C537 C538 C539 C540 C541 1-163-141-00 1-164-004-11 1-164-004-11 1-164-004-11 1-164-360-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.1uF 0.1uF 0.1uF 0.1uF 5% 10% 10% 10% 50V 25V 25V 25V 16V C542 C543 C544 C546 C547 1-164-004-11 1-107-826-11 1-126-177-11 1-107-826-11 1-107-826-11 CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 100uF 0.1uF 0.1uF 10% 10% 20% 10% 10% 25V 16V 10V 16V 16V C548 C549 C550 C551 C552 1-164-232-11 1-163-251-11 1-163-133-00 1-163-133-00 1-163-133-00 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 100PF 470PF 470PF 470PF 5% 5% 5% 5% 50V 50V 50V 50V 50V C553 C554 C555 C556 C557 1-164-004-11 1-104-953-11 1-163-251-11 1-163-141-00 1-164-232-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 47uF 100PF 0.001uF 0.01uF 10% 20% 5% 5% 25V 16V 50V 50V 50V C558 C626 C627 C806 C807 1-163-251-11 1-104-957-11 1-126-160-11 1-164-004-11 1-164-004-11 CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP 100PF 47uF 1uF 0.1uF 0.1uF 5% 20% 20% 10% 10% 50V 16V 50V 25V 25V C808 C809 C810 C811 C812 1-163-275-11 1-164-004-11 1-164-004-11 1-164-004-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.1uF 0.1uF 0.1uF 0.1uF 5% 10% 10% 10% 10% 50V 25V 25V 25V 25V C817 C818 C819 C822 C823 1-164-004-11 1-164-004-11 1-135-259-11 1-164-004-11 1-163-275-11 CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 10uF 0.1uF 0.001uF 10% 10% 20% 10% 5% 25V 25V 6.3V 25V 50V C824 C825 C828 C829 C830 1-164-004-11 1-164-489-11 1-163-275-11 1-163-243-11 1-163-243-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.22uF 0.001uF 47PF 47PF 10% 10% 5% 5% 5% 25V 16V 50V 50V 50V C831 C832 1-104-953-11 ELECT 1-163-141-00 CERAMIC 47uF 0.001uF 20% 16V 5% 50V < CONNECTOR > CN3001 1-779-070-21 PIN, CONNECTOR 12P < PIN JACK > JK3011 JK3012 JK3021 JK3022 JK3031 1-573-057-21 1-573-057-31 1-573-057-21 1-573-057-31 1-573-057-21 JACK, PIN 1P (LINE OUT HIGH FRONT L) JACK, PIN 1P (LINE OUT HIGH FRONT R) JACK, PIN 1P (LINE OUT MID REAR L) JACK, PIN 1P (LINE OUT MID REAR R) JACK, PIN 1P (LINE OUT SUB WOOFER L) JK3032 1-573-057-31 JACK, PIN 1P (LINE OUT SUB WOOFER R) ************************************************************ * A-3313-237-A MAIN BOARD, COMPLETE ********************* * 3-011-594-01 HEAT SINK (MAIN PC BOARD) 7-621-770-67 SCREW +B 2.6×6 7-685-146-11 SCREW +P 3×8 TYPE2 NON-SLIT < CAPACITOR > C501 C502 C503 C504 C505 1-126-027-11 1-136-960-11 1-126-012-11 1-163-038-00 1-104-955-11 ELECT FILM ELECT CERAMIC CHIP ELECT 1000uF 0.1uF 470uF 0.1uF 100uF 20% 25V 10% 160V 20% 16V 25V 20% 10V C506 C507 C508 C510 C511 1-104-955-11 1-164-004-11 1-164-004-11 1-164-004-11 1-126-177-11 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT 100uF 0.1uF 0.1uF 0.1uF 100uF 20% 10% 10% 10% 20% C512 C513 C514 C515 C516 1-104-945-11 1-164-004-11 1-125-710-11 1-126-935-11 1-164-004-11 ELECT CERAMIC CHIP DOUBLE LAYER ELECT CERAMIC CHIP 4.7uF 0.1uF 0.1F 470uF 0.1uF 20% 50V 10% 25V 5.5V 20% 16V 10% 25V C517 C518 C519 C520 C521 1-164-004-11 1-135-259-11 1-164-004-11 1-163-099-00 1-163-231-11 CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 10uF 0.1uF 18PF 15PF 10% 10% 10% 5% 5% C522 C523 C524 C525 C526 1-164-004-11 1-164-004-11 1-104-851-11 1-115-156-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 10uF 1uF 0.1uF 10% 25V 10% 25V 20% 10V 10V 10% 25V C527 C528 C529 C530 C531 1-164-004-11 1-164-232-11 1-107-826-11 1-107-826-11 1-107-826-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.01uF 0.1uF 0.1uF 0.1uF 10% 25V 50V 10% 16V 10% 16V 10% 16V 10V 25V 25V 25V 10V 25V 6.3V 25V 50V 50V < CONNECTOR/JACK > * CN501 CN502 CN503 * CN505 CN506 CN507 CN508 CN509 CN510 – 196 – 1-779-454-11 PIN, CONNECTOR (PC BOARD) 6P (POWER SUPPLY CONNECTOR) 1-778-830-11 CONNECTOR (BUS) (TO CD CHANGER) 1-778-832-11 CONNECTOR 16P 1-564-708-11 PIN, CONNECTOR (SMALL TYPE) 6P 1-564-718-11 PIN, CONNECTOR (SMALL TYPE) 2P 1-564-723-11 1-778-831-11 1-778-965-21 1-778-833-11 PIN, CONNECTOR (SMALL TYPE) 7P JACK 7P (TO ROTARY COMMANDER) CONNECTOR 12P CONNECTOR 14P MAIN Ref. No. Part No. Description Remark Ref. No. FB803 Part No. Description Remark 1-414-234-11 INDUCTOR, FERRITE BEAD < DIODE > < IC/RELAY > D501 D502 D503 D504 D505 8-719-049-38 8-719-053-18 8-719-977-22 8-719-977-22 8-719-977-22 DIODE DIODE DIODE DIODE DIODE 1N5404TU 1SR154-400TE-25 DTZ9.1 DTZ9.1 DTZ9.1 D506 D507 D508 D509 D511 8-719-801-78 8-719-977-12 8-719-053-18 8-719-976-99 8-719-041-97 DIODE DIODE DIODE DIODE DIODE 1SS184 DTZ6.8B 1SR154-400TE-25 DTZ5.1B MA113-TX D514 D515 D516 D517 D518 8-719-022-90 8-719-977-03 8-719-422-64 8-719-404-49 8-719-404-49 DIODE DIODE DIODE DIODE DIODE MA8160M DTZ5.6B MA8062-M MA111 MA111 D519 D520 D521 D522 D523 8-719-404-49 8-719-404-49 8-719-404-49 8-719-404-49 8-719-404-49 DIODE DIODE DIODE DIODE DIODE MA111 MA111 MA111 MA111 MA111 D524 D525 D527 D528 D530 8-719-404-49 8-719-404-49 8-719-422-64 8-719-422-64 8-719-422-64 DIODE DIODE DIODE DIODE DIODE MA111 MA111 MA8062-M MA8062-M MA8062-M D531 D532 D533 D535 D536 8-719-422-64 8-719-422-64 8-719-404-49 8-719-422-64 8-719-422-64 DIODE DIODE DIODE DIODE DIODE MA8062-M MA8062-M MA111 MA8062-M MA8062-M D538 D539 D540 D541 D542 8-719-420-90 8-719-420-90 8-719-422-64 8-719-422-64 8-719-422-64 DIODE DIODE DIODE DIODE DIODE MA8051-M MA8051-M MA8062-M MA8062-M MA8062-M D543 D544 D545 D546 D547 8-719-422-64 8-719-422-64 8-719-422-64 8-719-422-64 8-719-422-64 DIODE DIODE DIODE DIODE DIODE MA8062-M MA8062-M MA8062-M MA8062-M MA8062-M D548 D549 D550 D551 D552 8-719-422-64 8-719-422-64 8-719-422-64 8-719-422-64 8-719-422-64 DIODE DIODE DIODE DIODE DIODE MA8062-M MA8062-M MA8062-M MA8062-M MA8062-M D553 D554 D555 D556 D557 8-719-422-64 8-719-422-64 8-719-422-64 8-719-404-49 8-719-404-49 DIODE DIODE DIODE DIODE DIODE MA8062-M MA8062-M MA8062-M MA111 MA111 D558 D601 D603 8-719-422-64 DIODE MA8062-M 8-719-052-12 DIODE 1SS376TE-17 8-719-976-88 DIODE DTZ3.9B < FERRITE BEAD > FB802 1-414-234-11 INDUCTOR, FERRITE BEAD IC501 IC502 IC503 IC504 IC505 8-759-448-83 8-759-452-14 8-759-096-16 8-759-326-78 8-759-168-19 IC IC IC IC IC uPD78P058GC-933-3B9 MN18P83220S4K MM1175XF-T1 PST9140NL TA78L09F-TE12L IC506 IC507 IC509 IC510 IC511 8-759-234-77 8-759-439-67 8-759-360-79 8-759-157-21 8-759-054-12 IC IC IC IC IC TC4S66F TC7W126FU (TE12R) TC7W14F (TE12R) PQ05TZ11 PQ09RA1 IC513 IC515 IC516 IC517 IC603 8-759-084-79 8-759-163-78 8-759-484-51 8-759-344-91 1-755-188-11 IC TC7S14F (TE85R) IC NM24C04EM8-FL63 IC AT24C08N-10SI-SL383B IC RN5VD23AA-TL RELAY IC802 IC803 IC804 IC805 IC807 8-759-337-66 8-759-035-93 8-759-486-68 8-752-376-15 8-759-079-52 IC IC IC IC IC IC808 8-759-360-79 IC TC7W14F (TE12R) HD6413002F16 SC7S32F MBM29F400BA-70PFTN-MA02 CXK516100TM-70LL-TL TC74VHC08FS (EL) < COIL > L501 L503 L504 L506 L801 L802 L803 1-411-931-11 1-412-955-11 1-412-955-11 1-411-931-11 1-412-955-11 1-412-054-21 1-412-054-21 COIL, CHOKE (TROIDAL) 340uH INDUCTOR 22uH INDUCTOR 22uH COIL, CHOKE (TROIDAL) 340uH INDUCTOR 22uH INDUCTOR CHIP 2.2uH INDUCTOR CHIP 2.2uH < TRANSISTOR > Q501 Q502 Q503 Q504 Q505 8-729-025-88 8-729-421-22 8-729-025-88 8-729-421-22 8-729-424-08 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SB1386-T100-R UN2211 2SB1386-T100-R UN2211 UN2111 Q506 Q507 Q508 Q509 Q510 8-729-421-22 8-729-106-68 8-729-015-11 8-729-822-84 8-729-421-22 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR UN2211 2SD1615A-GP 2SD1802FAST-TL 2SB1202FAST UN2211 Q511 Q512 Q513 Q515 Q516 8-729-106-68 8-729-424-08 8-729-421-22 8-729-421-22 8-729-424-08 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SD1615A-GP UN2111 UN2211 UN2211 UN2111 Q517 Q518 Q519 Q520 Q521 8-729-230-49 8-729-230-49 8-729-421-22 8-729-230-49 8-729-424-08 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC2712-YG 2SC2712-YG UN2211 2SC2712-YG UN2111 Q522 Q525 Q526 Q528 8-729-024-31 8-729-421-22 8-729-421-22 8-729-011-95 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR XN1111-TX UN2211 UN2211 RN-2426 – 197 – MAIN Ref. No. Part No. Description Remark Q529 8-729-421-22 TRANSISTOR UN2211 Q531 Q532 Q533 Q535 Q536 8-729-421-22 8-729-424-08 8-729-421-22 8-729-011-95 8-729-011-95 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR UN2211 UN2111 UN2211 RN-2426 RN-2426 Q537 Q538 Q541 Q542 Q605 8-729-027-50 8-729-027-50 8-729-230-49 8-729-040-17 8-729-920-21 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC123JKA-T146 DTC123JKA-T146 2SC2712-YG 2SD2164-K DTC314TKH04 Q606 Q607 Q609 8-729-920-21 TRANSISTOR DTC314TKH04 8-729-424-08 TRANSISTOR UN2111 8-729-421-22 TRANSISTOR UN2211 < RESISTOR/CHIP CONDUCTOR > R356 R357 R358 R359 R501 1-216-206-00 1-216-206-00 1-216-206-00 1-216-206-00 1-216-049-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 2.2K 2.2K 2.2K 2.2K 1K 5% 5% 5% 5% 5% 1/8W 1/8W 1/8W 1/8W 1/10W R502 R503 R504 R505 R507 1-216-057-00 1-216-057-00 1-216-049-00 1-216-049-00 1-216-061-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 2.2K 2.2K 1K 1K 3.3K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R508 R509 R510 R511 R512 1-216-049-00 1-216-049-00 1-216-057-00 1-216-057-00 1-216-057-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 2.2K 2.2K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R514 R515 R516 R517 R520 1-216-222-00 1-216-206-00 1-216-841-11 1-216-073-00 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 2.2K 47K 10K 100K 5% 5% 5% 5% 5% 1/8W 1/8W 1/16W 1/10W 1/16W R523 R524 R525 R526 R527 1-216-845-11 1-216-825-11 1-216-837-11 1-216-833-11 1-216-837-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 2.2K 22K 10K 22K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R528 R530 R531 R533 R534 1-216-833-11 1-216-049-00 1-216-295-00 1-216-819-11 1-216-845-11 METAL CHIP 10K METAL CHIP 1K CONDUCTOR, CHIP (2012) METAL CHIP 680 METAL CHIP 100K 5% 5% 1/16W 1/10W 5% 5% 1/16W 1/16W R535 R536 R537 R538 R539 1-216-845-11 1-216-815-11 1-216-805-11 1-216-805-11 1-216-805-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 330 47 47 47 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R540 R541 R542 R543 R544 1-216-852-11 1-216-833-11 1-216-833-11 1-216-845-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 390K 10K 10K 100K 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R547 R548 1-216-821-11 METAL CHIP 1-216-081-00 METAL CHIP 1K 22K 5% 5% 1/16W 1/10W Ref. No. Part No. Description Remark R550 R551 R556 1-216-845-11 METAL CHIP 1-216-864-11 METAL CHIP 1-216-817-11 METAL CHIP 100K 0 470 5% 5% 5% 1/16W 1/16W 1/16W R557 R558 R559 R560 R561 1-216-821-11 1-216-833-11 1-216-829-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 10K 4.7K 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R562 R563 R568 R569 R570 1-216-025-00 1-216-025-00 1-216-845-11 1-216-845-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100K 100K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/16W 1/16W 1/16W R571 R572 R573 R574 R576 1-216-081-00 1-216-821-11 1-216-821-11 1-216-821-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22K 1K 1K 1K 100K 5% 5% 5% 5% 5% 1/10W 1/16W 1/16W 1/16W 1/16W R577 R579 R580 R581 R582 1-216-057-00 1-216-831-11 1-216-831-11 1-216-097-00 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 2.2K 6.8K 6.8K 100K 1K 5% 5% 5% 5% 5% 1/10W 1/16W 1/16W 1/10W 1/16W R583 R584 R585 R588 R590 1-216-821-11 1-216-821-11 1-216-821-11 1-216-017-00 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 1K 47 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/10W 1/16W R591 R593 R630 R631 R632 1-216-821-11 1-216-821-11 1-216-089-00 1-208-478-11 1-208-478-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 47K 470 470 5% 5% 5% 2% 2% 1/16W 1/16W 1/10W 1/8W 1/8W R633 R634 R635 R801 R803 1-216-222-00 1-216-222-00 1-216-017-00 1-216-097-00 1-216-819-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 47 100K 680 5% 5% 5% 5% 5% 1/8W 1/8W 1/10W 1/10W 1/16W R804 R805 R808 R810 R811 1-216-845-11 1-216-097-00 1-216-845-11 1-216-049-00 1-216-097-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 100K 1K 100K 5% 5% 5% 5% 5% 1/16W 1/10W 1/16W 1/10W 1/10W R819 R821 R822 R824 R825 1-216-845-11 1-216-821-11 1-216-033-00 1-216-025-00 1-216-298-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 1K 220 100 2.2 5% 5% 5% 5% 5% 1/16W 1/16W 1/10W 1/10W 1/10W R828 R829 R830 R831 R862 1-216-298-00 1-216-298-00 1-216-298-00 1-216-821-11 1-216-813-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 2.2 2.2 2.2 1K 220 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/16W 1/16W R863 R864 R865 R866 R867 1-216-817-11 1-216-817-11 1-216-817-11 1-216-817-11 1-216-813-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470 470 470 470 220 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W – 198 – MAIN Ref. No. Remark OPEN/CLOSE 1 Ref. No. Part No. Description R868 R869 R870 R871 R872 1-216-817-11 1-216-864-11 1-216-815-11 1-216-817-11 1-216-041-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470 0 330 470 470 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/10W R873 R874 R875 R876 R882 1-216-041-00 1-216-097-00 1-216-097-00 1-216-097-00 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470 100K 100K 100K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/16W X501 1-579-886-21 VIBRATOR, CRYSTAL (32.768kHz) X502 1-767-452-11 VIBRATOR, CERAMIC (5MHz) X503 1-767-261-21 VIBRATOR, CERAMIC (8MHz) X802 1-767-426-21 VIBRATOR, CERAMIC (14.745MHz) ************************************************************ R883 R884 R885 R889 R890 1-216-809-11 1-216-809-11 1-216-849-11 1-216-809-11 1-216-097-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 220K 100 100K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/10W * R891 R892 R894 R895 R896 1-216-097-00 1-216-097-00 1-216-025-00 1-216-025-00 1-216-817-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 100 100 470 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/16W R897 R898 R901 R902 R903 1-216-049-00 1-216-049-00 1-216-833-11 1-216-833-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 10K 10K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/16W 1/16W 1/16W R904 R905 R907 R908 R909 1-216-833-11 1-216-833-11 1-216-845-11 1-216-097-00 1-216-295-00 METAL CHIP 10K METAL CHIP 10K METAL CHIP 100K METAL CHIP 100K CONDUCTOR, CHIP (2012) 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/10W R910 1-216-845-11 METAL CHIP 5% 1/16W < NETWORK RESISTOR > RA801 RA802 RA803 RA804 RA805 1-233-412-11 1-216-182-00 1-216-182-00 1-216-182-00 1-216-182-00 RES, CHIP NETWORK 1K×4 (3216) RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 220×4 (3216) RA806 RA807 RA808 RA809 RA810 1-216-182-00 1-216-182-00 1-216-182-00 1-216-182-00 1-216-182-00 RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 220×4 (3216) RA811 RA812 RA813 RA814 RA815 1-233-576-11 1-233-789-11 1-233-412-11 1-233-412-11 1-233-810-21 RES, CHIP NETWORK 100×4 RES, NETWORK 10K×2 (1608) RES, CHIP NETWORK 1K×4 (3216) RES, CHIP NETWORK 1K×4 (3216) RES, NETWORK 100K×4 (3216) RA816 RA817 RA818 RA819 RA820 1-216-182-00 1-216-182-00 1-216-182-00 1-216-182-00 1-216-182-00 RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 220×4 (3216) RA821 RA822 RA823 RA826 1-216-182-00 1-216-182-00 1-216-182-00 1-233-412-11 RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 220×4 (3216) RES, CHIP NETWORK 1K×4 (3216) Description Remark < THERMISTOR > TH501 1-810-940-11 THERMISTOR, POSITIVE < VIBRATOR > 1-662-634-12 OPEN/CLOSE 1 BOARD ****************** < CONNECTOR > CN21 100K Part No. OPEN/CLOSE 2 1-580-789-21 PIN, CONNECTOR (SMD) 6P < PHOTO INTERRUPTER > PH21 8-719-988-14 PHOTO REFLECTOR PR-11-B (FRONT PANEL DESORPTION MOTOR ROTATION DETECT) < RESISTOR > R21 R22 1-216-049-00 METAL CHIP 1-216-097-00 METAL CHIP 1K 100K 5% 5% 1/10W 1/10W < SWITCH > S21 1-572-688-11 SWITCH, PUSH (1 KEY) (FRONT PANEL POSITION DET) S22 1-572-688-11 SWITCH, PUSH (1 KEY) (FRONT PANEL POSITION DET) S23 1-762-621-21 SWITCH, PUSH (1 KEY) (FRONT PANEL POSITION DET) ************************************************************ 1-662-635-12 OPEN/CLOSE 2 BOARD ****************** * < CAPACITOR > C11 C12 C13 C14 1-124-589-11 1-124-589-11 1-163-038-00 1-163-038-00 ELECT ELECT CERAMIC CHIP CERAMIC CHIP 47uF 47uF 0.1uF 0.1uF < CONNECTOR > CN11 CN12 CN13 CN14 CN15 1-778-833-11 1-580-789-21 1-580-055-21 1-580-438-21 1-580-438-21 CONNECTOR 14P PIN, CONNECTOR (SMD) 6P PIN, CONNECTOR 2P CONNECTOR, FPC 4P CONNECTOR, FPC 4P < DIODE > D11 D12 D13 8-719-422-64 DIODE MA8062-M 8-719-422-64 DIODE MA8062-M 8-719-420-14 DIODE MA8082-M < IC > IC11 8-759-231-92 IC TA7291P < TRANSISTOR > Q11 – 199 – 8-729-900-53 TRANSISTOR DTC114EK 20% 16V 20% 16V 25V 25V SENSOR SW TRANSLATION Ref. No. R704 Part No. TRANSLATION (CONNECTOR) Description 1-216-045-00 METAL CHIP Remark 680 5% Ref. No. 1/10W Description Remark < RESISTOR > < SWITCH > SW701 1-571-754-31 SWITCH, PUSH (1 KEY) (DISC CHUCKING END DET) ************************************************************ 1-664-111-12 SW BOARD ********* * Part No. R52 R53 R54 R55 R56 1-216-821-11 1-216-821-11 1-216-849-11 1-216-849-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP R57 1-216-821-11 METAL CHIP 1K 1K 220K 220K 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W 1K 5% 1/16W < SWITCH > < CAPACITOR > C801 C802 C803 C804 C805 1-104-823-11 1-164-004-11 1-164-004-11 1-164-004-11 1-164-004-11 TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 47uF 0.1uF 0.1uF 0.1uF 0.1uF 20% 10% 10% 10% 10% S51 1-570-909-11 SWITCH, TACTIL (REFLOW TYPE) (RESET) ************************************************************ 16V 25V 25V 25V 25V 1-663-877-12 TRANSLATION (CONNECTOR) BOARD ****************************** * < CAPACITOR > < CONNECTOR > C41 C42 CNJ801 1-778-816-21 CONNECTOR, FPC 10P CNP801 1-580-055-21 PIN, CONNECTOR 2P 1-162-964-11 CERAMIC CHIP 1-164-156-11 CERAMIC CHIP 0.001uF 0.1uF 10% 50V 25V < CONNECTOR > < IC > IC801 CN41 CN42 8-759-040-83 IC BA6287F < RESISTOR > < RESISTOR > R805 1-216-089-00 METAL CHIP 47K 5% R42 1/10W 1-216-821-11 METAL CHIP 1K 5% 1/16W < SWITCH > < SWITCH > SW802 1-692-864-21 SWITCH, PUSH (1 KEY) (MAGAZINE LOCK DET) SW803 1-571-754-31 SWITCH, PUSH (1 KEY) (LINEAR SLIDE LEVER POSITION DET) SW804 1-571-754-31 SWITCH, PUSH (1 KEY) (MAGAZINE DET) ************************************************************ S41 1-762-805-21 SWITCH, PUSH (1 KEY) (NOSE DET) S42 1-570-909-11 SWITCH, TACTIL (REFLOW TYPE) (RESET) ************************************************************ 1-663-878-12 TRANSLATION (HIDE) BOARD ************************ * 1-662-633-12 TRANSLATION BOARD ****************** * 1-564-731-11 PIN, CONNECTOR (SMALL TYPE) 15P 1-774-944-11 SOCKET, CONNECTOR 14P < CAPACITOR > C31 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V < CAPACITOR > < CONNECTOR > C51 C52 C53 C54 1-164-156-11 1-162-964-11 1-162-964-11 1-164-156-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.001uF 0.001uF 0.1uF 25V 10% 50V 10% 50V 25V CN31 CN32 * CN33 < CONNECTOR > CN51 CN52 CN53 CN54 D53 D54 D55 1-774-944-11 1-774-276-21 1-770-736-21 1-770-736-21 D31 D32 < DIODE > IC31 < IC > IC51 < DIODE > SOCKET, CONNECTOR 14P SOCKET, CONNECTOR 16P SOCKET, CONNECTOR 14P SOCKET, CONNECTOR 14P 8-719-422-64 DIODE MA8062-M 8-719-422-64 DIODE MA8062-M 8-719-422-64 DIODE MA8062-M 1-770-736-21 SOCKET, CONNECTOR 14P 1-774-276-21 SOCKET, CONNECTOR 16P 1-564-717-11 PIN, CONNECTOR (SMALL TYPE) 15P 8-719-422-64 DIODE MA8062-M 8-719-422-64 DIODE MA8062-M < IC > 8-759-084-79 IC TC7S14F (TE85R) < RESISTOR > R31 1-216-821-11 METAL CHIP 1K 5% 1/16W R32 1-216-821-11 METAL CHIP 1K 5% 1/16W R33 1-216-845-11 METAL CHIP 100K 5% 1/16W ************************************************************ 8-759-079-48 IC TC74VHC02FS (EL) – 200 – TRANSLATION (CONNECTOR) Ref. No. Part No. Description TRANSLATION (HIDE) Remark < SWITCH > S41 1-762-805-21 SWITCH, PUSH (1 KEY) (NOSE DET) S42 1-570-909-11 SWITCH, TACTIL (REFLOW TYPE) (RESET) ************************************************************ 1-663-878-12 TRANSLATION (HIDE) BOARD ************************ * Ref. No. Part No. TUNER (U) ASSY Description 461 464 474 1-801-564-21 LIQUID CRYSTAL DISPLAY MODULE 1-664-508-11 SWITCH FLEXIBLE BOARD 1-777-717-11 CORD (WITH CONNECTOR) (POWER) 514 516 559 565 1-662-967-11 1-662-968-11 A-3301-206-A 1-782-714-11 Remark 615 FLEXIBLE 1 BOARD FLEXIBLE 2 BOARD TUNER (U) ASSY (FM/AM TUNER UNIT) CORD (WITH CONNECTOR) (ANT) (SUB (FM)/MAIN (FM/AM)) 1-782-199-11 CORD (WITH CONNECTOR) (DIN) 616 618 F1 F501 M1 1-782-200-11 1-543-798-11 1-532-796-11 1-532-731-11 A-3301-104-A < CAPACITOR > C31 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V < CONNECTOR > CN31 CN32 * CN33 1-770-736-21 SOCKET, CONNECTOR 14P 1-774-276-21 SOCKET, CONNECTOR 16P 1-564-717-11 PIN, CONNECTOR (SMALL TYPE) 15P M501 X-3373-838-1 MOTOR ASSY (ELEVATOR UP/DOWN) M502 X-3373-839-1 MOTOR (N) ASSY (DISC LOAD/SAVE) M801 X-3373-838-1 MOTOR (P) ASSY (DISC EJECT) PRG401 1-454-580-21 SOLENOID, PLUNGER SW501 1-571-300-31 SWITCH, ROTARY (HOME/TOP DET) ************************************************************ < DIODE > D31 D32 8-719-422-64 DIODE MA8062-M 8-719-422-64 DIODE MA8062-M ************** HARDWARE LIST ************** < IC > IC31 CORD (WITH CONNECTOR) (HIDE) FILTER, CLAMP (FERRITE CORE) FUSE (BLADE TYPE) (AUTO FUSE) (5A) FUSE (3A/32V) MOTOR ASSY (FRONT PANEL DESORPTION) 8-759-084-79 IC TC7S14F (TE85R) < RESISTOR > R31 1-216-821-11 METAL CHIP 1K 5% 1/16W R32 1-216-821-11 METAL CHIP 1K 5% 1/16W R33 1-216-845-11 METAL CHIP 100K 5% 1/16W ************************************************************ A-3301-206-A TUNER (U) ASSY (FM/AM TUNER UNIT) ************** 1-782-714-11 CORD (WITH CONNECTOR) (ANT) (SUB (FM)/MAIN (FM/AM)) 7-685-792-09 +PTT 2.6X6, S TITE < CONNECTOR > CN101 1-566-001-11 PIN, CONNECTOR (PC BOARD) 4P CN605 1-564-722-11 PIN, CONNECTOR (SMALL TYPE) 6P CN606 1-564-718-11 PIN, CONNECTOR (SMALL TYPE) 2P CN607 1-564-723-11 PIN, CONNECTOR (SMALL TYPE) 7P CN609 1-770-629-21 PIN, CONNECTOR 12P ************************************************************ #1 #2 #3 #4 #5 7-683-405-04 7-621-773-95 7-621-775-10 7-683-413-05 7-683-404-04 BOLT, HEXAGON SOCKET 3X10 SCREW +B 2.6X6 SCREW +P 2.6X4 BOLT, HEXAGON SOCKET 2.6X8 BOLT, HEXAGON SOCKET 3X8 #6 #7 #8 #9 #10 7-682-558-09 7-627-850-27 7-685-792-09 7-685-782-01 7-685-781-09 SCREW +P 4X4 SCREW, PRECISION +P 1.4X3 SCREW +PTT 2.6X6 (S) SCREW +PTT 2X5 (S) SCREW +PTT 2X4 (S) #11 #12 #13 #14 #16 7-685-852-04 7-682-545-09 7-685-102-19 7-685-780-01 7-624-102-04 SCREW +BVTT 2X5 (S) SCREW +P 3X4 SCREW (+BTP) (2X4) SCREW +PTT 2X3 (S) STOP RING 1.5, TYPE -E #17 #18 #19 #20 #21 7-624-104-04 7-685-103-19 7-627-554-37 7-621-259-25 7-627-553-27 STOP RING 2.0, TYPE -E SCREW +P 2X5 TYPE2 NON-SLIT SCREW, PRECISION +P 2X1.8 TYPE1 SCREW +P 2.6X4 SCREW, PRECISION +P 2X2.5 MISCELLANEOUS ************** 58 67 71 153 161 1-782-287-11 1-473-994-11 1-782-286-11 1-664-157-11 1-664-155-11 CABLE, FLAT (FWCF) (30 CORE) DC/DC CONVERTER UNIT CABLE, FLAT (FWCF) (8 CORE) SWITCH FLEXIBLE BOARD RF FLEXIBLE BOARD 162 359 361 368 ! 409 1-664-156-11 1-777-720-11 1-777-721-11 1-643-083-11 8-848-310-11 DRIVER FLEXIBLE BOARD CABLE, FLEXIBLE FLAT (4 CORE) CABLE, FLEXIBLE FLAT (8 CORE) MOTOR FLEXIBLE BOARD OPTICAL PICK-UP KSS-400A 410 411 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. X-2625-210-1 SLED MOTOR GEAR ASSY 8-835-456-01 DC MOTOR SSC-02E01S (SPINDLE) – 201 – Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le neméro spécifié. XES-Z50 Ver 1.1 Ref. No. Part No. Description #22 #23 #24 #25 #26 7-627-553-37 7-627-852-17 7-628-253-15 7-627-553-68 7-685-102-21 SCREW, PRECISION +P 2X3 SCREW, PRECISION +P 1.7X4 TYPE3 SCREW +PS 2X5 SCREW, PRECISION +P 2X6 SCREW +P 2X4 TYPE2 #27 #28 #29 #30 #32 7-627-556-78 7-685-794-09 7-621-772-18 7-627-553-18 7-621-770-67 SCREW, PRECISION +P 2.6X6 TYPE1 SCREW +PTT 2.6X10 (S) SCREW +B 2X4 SCREW, PRECISION +P 2X2 SCREW +B 2.6X6 Remark Ref. No. Part No. Description 828 829 830 831 832 3-012-442-01 7-685-792-09 3-013-264-01 1-782-274-11 1-782-275-11 BRACKET (ROTARY COMMANDER) SCREW +PTT 2.6X6 (S) COVER, 3P TERMINAL TABLE CORD, ANTENNA (MAIN) CORD, ANTENNA (SUB) 833 X-3366-405-1 SCREW ASSY (EXP), FITTING #33 7-685-146-11 SCREW +P 3X8 TYPE2 NON-SLIT #34 7-621-773-87 SCREW +B 2.6X10 #35 7-621-772-10 SCREW +B 2X4 #36 7-621-255-15 SCREW +P 2X3 ************************************************************ 801 1-475-385-11 3-014-560-01 3-858-942-11 3-858-943-11 3-859-709-11 802 804 ACCESSORIES ************ REMOCON, WIRELESS (RM-X67) BINDER, INSTRUCTION MANUAL MANUAL, INSTRUCTION (ENGLISH) MANUAL, INSTRUCTION, INSTALL (ENGLISH) VOLUME, EXPLANATION 1-473-967-12 ROTARY COMMANDER (RM-X66) (including bracket) 9-939-690-01 ROTARY COMMANDER (BRACKET) (for RM-X66) 9-939-845-01 COVER, BATTERY CASE (for RM-X67) X-3373-405-1 MAGAZINE (XES) ASSY ************************************************************ Remark 803 805 806 833 809 810 811 813 812 814 MOUNTING HARDWARE ******************* 817 815 801 * 802 803 * 804 805 3-367-968-01 3-370-687-01 3-372-142-03 3-916-161-11 3-909-685-01 SCREW (M5X8) SPACER (N) CUSHION (3) FRAME, FITTING SPRING (FITTING) 806 809 810 811 812 3-909-686-11 3-702-658-01 X-3370-886-1 7-685-161-01 not supplied COLLAR TOOL (REMOVE) STAND ASSY SCREW +P 4X12 TYPE4 813 814 815 816 817 3-939-604-01 3-389-594-01 X-3373-408-1 3-302-126-01 3-008-210-01 COVER (STAND) CLAMP, CORD BRACKET ASSY SCREW, TAPPING (DIA. 5X20) BRACKET (ES) 824 818 819 820 821 822 7-682-964-09 3-013-529-01 3-013-207-01 3-014-510-01 3-013-797-01 SCREW +PSW 4X14 NUT (UPS-F.M8) SHEET (FITTING) SHEET (BRACKET ES) WASHER (M8 STAINLESS COAT) 826 823 824 825 826 827 7-685-248-14 3-012-265-01 3-937-921-01 1-777-716-11 1-777-717-11 SCREW +KTP 3X12 TYPE4 HOLDER TAPE (HOLDER) CORD, CONNECTION (BUS) CORD (WITH CONNECTOR) (POWER) 822 816 818 819 821 820 823 829 – 202 – 825 827 830 828 831 832 XES-Z50 MEMO – 203 – XES-Z50 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. 1.1 1.0 Date 2001.09 1997.07 1997.06 Description of Revision Change of Part No. for ROTARY COMMANDER (RM-X66) Correction-1 New (SPM-01020)
Similar documents
CDX-GT800D/GT805DX
Note If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit fi...
More informationservice manual
as to keep it away from hot or high-voltage parts. When mounting parts or routing wires, therefore, be sure to duplicate the original layout.
More informationJK125P, JK300P and JK300HP
technology. enabling complete cycle programming triggered by a single command, patented Luminator TM fiber optic beam delivery with back reflection protection; pulse shaping capability for tighter ...
More information