UA center channel Speaker MountsEnglish US printing.pub
Transcription
UA center channel Speaker MountsEnglish US printing.pub
Installation Instructions EAR-C: Center Speaker Mount Kit • Thank you for purchasing an OmniMount product. • Fits the UCL-X, G3FP and UAL Maximum Weight Capacity: 40lbs. (18.14 kg)* IMPORTANT: Consult a qualified installer if you have any questions regarding the proper installation of this wall mount system. Specifications are subject to change without prior notice. Every effort has been made to provide accurate and error-free assembly and installation. OmniMount Systems disclaims liability for any difficulties arising from the interpretation of information contained in these instructions. If OmniMount products are used for purposes other than their original intent, OmniMount, its distributors and retailers shall not be held responsible or liable for injuries or property damage, direct, indirect, or consequential, which may arise from the inability to use this product safely, properly, and in the manner for which it has been designed and manufactured. Warranty does not apply to products which have been lost, damaged by misuse, abuse, or accident. EAR-C UAL Spkr Kit—RevA—1003281—3/06 8 *Ensure the total combined weight of the Display, the Speakers and other attachments does not exceed the weight capacity of the flat panel Questions? Call 1-800-MOUNT-IT (USA only) Step 4: Adjust the Bracket To adjust the speakers vertical position, loosen the Adjustment Screw (Fig 2) and slide the Adjustment Bracket into the desired position. NOTE: Support speaker while making adjustments. Fig. 2 Step 5: Attach the Speaker Cables Connect the Speaker’s cables to the components as required. If available, use the mount’s cable management system. 2 7 Speaker Adapter (optional attachment) Components: i ID Use Speaker Adapter when the speaker’s mounting holes are farther apart then the Bracket can accommodate. A. Attach the Speaker Adapter to the speaker’s threaded inserts using Screw (D-K) and Washer (L-N), tighten securely. ii B. Thread Screw #1 up through the top of the Speaker Adapter and into the bottom of the Adjustment Plate. Description i Back Plate ii Clamp iii Adjustment Screw iv Washer v Adjustment Plate vi Speaker Adapter A iii iv v Spacers (optional attachment) A. For speakers with recessed mounting holes vi Use Long Screws (E, G, I, K) A B. For speakers with a curved back Hardware Kit ID Description Qty. A Screw #1 - M6 x 16 4 B Hex Key - 4mm 1 C Spacer - 1/2" 2 D Phillips Screw - M4 x 35 3 E Phillips Screw - M4 x 50 3 F Phillips Screw - M5 x 35 3 G Phillips Screw - M5 x 50 3 H Phillips Screw - M6 x 35 3 I Phillips Screw - M6 x 50 3 J Phillips Screw - 1/4"-20 x 1 1/2" 3 K Phillips Screw - 1/4"-20 x 2" 3 L Flat Washer - 4mm 3 M Flat Washer - 5mm 3 N Flat Washer - 1/4" 3 O Hex Nut - M4 3 P Hex Nut - M5 3 Q Hex Nut - M6 3 R Hex Nut - 1/4"-20 3 The EAR-C can be installed with the Display attached to the UAL Step 1: Separate the Back Plate Remove the Adjustment Screw and Washer, then slide the Back Plate free. 6 3 Step 2: Install the Back Plate Step 3: Attach the Speaker Never Exceed The 35 lbs. Weight Capacity Examine the speaker to determine the appropriate installation type. A. Hang the Back Plate from B. Attach the Clamp to the Back Plate C. Align the hash marks (Fig. 1) and the UAL’s top rail. using Screw #1 securely tighten Screw #1 To determine the appropriate installation hardware (C-R) consult the speaker’s instruction manual or experiment with different Screws. Place the speaker in the desired horizontal position before tightening the Screws. Caution: NEVER force screws, as damage may occur. NEVER use an electric drill on these screws. Fig. 1 Threaded Inserts Insert Screw (D-K) through the Washer (L-N) and Adjustment Plate and thread into the speakers threaded inserts. Tighten securely. Step 2: Attach the Adjustment Plate Keyhole Mounting A. With the Display mounted to the UAL, slide the B. Hold the Adjustment Plate in the desired position then thread the Adjustment Screw Adjustment Plate over the Back Plate. through the Washer and Adjustment Plate into the Back Plate. Tighten securely. A. Thread the Screw (D-K) through the Bracket, Washer (L-N) and into the Nut (O-R). Leave space between the Screw and the Bracket (See B). B. Push against Nuts, then lower the speaker onto the Screws. C. Pull the speaker away from the mount to create tension while tightening the Nut. NOTE: Ensure the speaker is low enough so that it will not interfere with the display, 4 5