sc 8 0 series - Pavilion Construction

Transcription

FA LCO N T S E R I E S
Simply put, the Falcon T-Series lock is the most versatile lockset
in the industry. This extra heavy duty lock can accept any
manufacturer’s cylinder, and the cylinder can easily be removed
for quick, easy re-keying. Redesigned with a compression spring
behind the cylinder, the T-Series is now stronger than ever and
lever sag has been virtually eliminated. This adaptable lock is well
suited to either new construction or retrofit use in buildings as
varied as multi-family, retail, institutional and government/military.
F E AT U R E S
Brass or cold-formed
steel construction,
zinc plated and
dichromated for rust
resistance
Proven compression
spring design supports
levers, eliminating lever
sag and provides years
of reliable service
Heavy wrought brass
or bronze roses over
steel through-bolted
rose inserts
PressureRelease™
outside lever disengages
when locked to protect
internal mechanisms
3
T SERIES
LEVER DESIGNS
Levers
Levers are solid pressure cast zinc, finished to match mating parts. Roses are wrought brass or bronze installed over steel through-bolted
rose inserts. Pressure Release™ levers are standard. Levers are secured by a spring-loaded retainer. Retainer cannot be depressed when
locks have been locked.
5”
3-1/2”
3-1/4”
A
Avalon
5”
3-1/2”
3-1/4”
D
Dane
5”
3-1/2”
3-1/4”
Q
Quantum
Abrasive Coated Levers
All levers are available with abrasive coating along the length of the lever to identify entrances to hazardous areas to the handicapped.
To order add: “with abrasive coated outer lever” in detail section of order.
4
T SERIES
L O C K F E AT U R E S A N D S P E C I F I C AT I O N S
Lock Features
Door Thickness: 1-3/4” to 2-1/8” standard. Thin door adapter
kit (A30775-000-00) available for doors thinner than 1-3/4”,
please specify door thickness.
Backset: 2-3/4” standard. 2-3/8” also available.
Link (A22161-005-10) available for 5” backset.
Mechanism: Parts constructed of brass or cold formed steel,
zinc plated and dichromated for rust resistance. Springs are
stainless steel.
Attachment: Lock chassis secured to door by threaded mounting
nuts. Completely preassembled outer trim and inner spindle assembly
are through-bolted over chassis using (2) 10-32 screws. Adding
rose and lever to inner spindle assembly completes installation.
Handing: Locks are non-handed.
Cylinders: Drilled with 6-pin chambers, pinned in 5. Pinning in 6
chambers available when specified, at no cost. 7-pin cylinders also
available. Cylinder assemblies removable to rekey. Also available
with 6 or 7-pin interchangeable core cylinders. Cylinder housings
and plugs machined from solid brass. Springs are phosphor bronze.
Two nickel silver keys furnished standard. Interchangeable core
design is available for small format (SFIC) and large format for
most manufacturers, see page 8.
Keyways: “G” keyway standard on conventional cylinders. “A”
keyway standard on I/C core cylinders. Also available with some
optional keyways.
Trim: Roses are heavy wrought brass or bronze, installed over
pressure cast rose inserts which are through-bolted through door.
Levers are pressure cast (solid levers–no inserts) material finished
to match mating parts.
Latches: 9/16” bolt projection, UL listed with latch faceplates
2-1/4” x 1-1/8” with square corners standard. 3/4” projection,
UL listed latch with 2-3/4” backset also available. Adjustable front
standard. See page 10 for optional latches.
Strikes: 4-7/8” x 1-1/4” ANSI strike with curved lip to meet ANSI
A115.2 door frame preparation standard. Consult page 11 for
other available strike sizes and configurations.
Screws: Furnished with combination screws for use in wood or
metal doors and frames.
Electrified Functions: Available in 24 VDC .185 AMP.
ANSI/BHMA: Meets ANSI/BHMA A156.2, Series 4000, Grade 1.
UL: 3 hour A label.
Falcon Lock T Series Specifications
Key-in-lever cylindrical locksets shall be Falcon Lock T Series or
equal and meet the following requirements:
• All locks shall meet the new ANSI/BHMA A156.2, Series 4000,
Grade 1 for key-in-lever locksets.
• Locksets shall be UL Listed (3 hour A Label).
• Locksets shall be provided standard with Pressure Release™
feature. When outside lever is locked, it is not rigid but will
move freely without operating the latch bolt.
• Lever trim shall have individual heavy-duty compression springs
behind rose for lever return and to prevent lever sag. Trim shall
be through-bolted with two (2) 10-32 screws coated with thread
sealant to provide strength and resistance to loosening. Inner
2-3/8”, 2-3/4”
5/16” Dia. thru hole
and outer trim shall “bottom out” to prevent door collapse.
Roses shall be minimum of 3-1/2” diameter.
• All lever designs shall be solid and meet the federal ADA and
state disability requirements. Inside levers shall be attached by
Allen-head set screw to prevent tampering or vandalism.
• Locksets shall adjust to fit door thickness from 1-3/4” to 21/8”.
• All locksets shall be non-handed and not require field
disassembly for re-handing.
• Preparation for door must be non-handed.
Acceptable manufacturer: FALCON LOCK
Backset (from center of door for beveled stile)
CL door, lock & strike are common
5/32”
1” Dia.
3/4”
3-1/2”
4-7/8”
2-3/4”
2-1/4”
1-1/8”
1-1/4”
5/16”
3-3/8”
5/32”
x 1/8”
Deep
4-1/8”
2-25/32”
Elevation
14
2-1/8” Dia.
1-1/8”
Door Edge
9/16”
1-1/16”
Standard Strike
3/8”
Machined steel lever spindle carries high levels
of torque and shear. This spindle is re-used when
upgrading existing locks to the new design.
Heavy-duty case zinc rose insert accommodates
the new style spring. This insert is replaced when
upgrading to the new design.
New stamped steel torque plates hold the
springs in place and transfer the spring
energy to the spindle and lever assembly.
Stainless steel compression springs replace steel
torsion springs, providing the most reliable and
robust method of supporting levers.
New retaining ring holds
the assembly together.
Falcon T-series locks feature our high performance compression springs. This newly designed spring far exceeds ANSI/BHMA
requirements for cycle tests, and ensures the most robust support for levers. Unlike typical torsion springs that can break at the
bend points, this new design will provide years of reliable service even in high-use applications. A retrofit kit is available to outfit
your existing T-series locks with this new, more robust spring design.
5
To order Falcon T Series locksets, please consult page 15 for ordering information and assistance.
Indicates interchangeable core available.
Catalog
Number
Description
ANSI No.
& Grade
T571
Dormitory Lock
Deadlocking latch bolt by levers except when locked by push button in inside lever.
Key in outside lever locks or unlocks outside lever and releases button. Closing door
releases push button. Inside lever always free.
F90-1
T581
Storeroom Lock
Deadlocking latch bolt by lever inside or key outside. Outside lever is inoperable.
Inside lever always free.
F86-1
T851
Storeroom (Electrified – Fail Safe)
Inside Lever Always Free. Latch bolt operated by lever from either side except when
outer lever is electrically locked. When outer lever is locked (inoperable), latch bolt
retracted by key in cylinder outside. 24 volt DC .185 Amps, continuous duty.
T881
Storeroom (Electrified – Fail Secure)
Inside Lever Always Free. Deadlocking latch bolt operated by lever inside at all times.
Outside lever inoperable until electrically unlocked, then latch bolt from either side.
When outside lever is inoperable latch bolt retracted by key in cylinder outside. 24
volt DC .185 Amps, continuous duty..
T12
Dummy Trim
Single Trim-surface mounted rigid lever.
Function
7
W Series
Medium Duty, Grade 2 Cylindrical Lever and Knob Locks
FA L C O N W S E R I E S
Whether your application is government/military, retail, industrial or multi-family, there’s a
W Series lock that fits perfectly. In two popular lever and two popular knob styles Falcon can
match most commercial door trim.
The Falcon W Series locks feature conventional cylinders and small format interchangeable
cores that are compatible with SFIC products from other manufacturers. Our conventional
cylinders are available in all Falcon conventional key sections as well as Schlage C Keyway,
which we now masterkey across the complete Falcon product line.
If quality product at a value price is what you are looking for, the Falcon W Series is the lock
for you. And they’re backed by one of the best names in the business, Ingersoll Rand.
F E AT U R E S
Stainless steel
latch bolt
Solid, pressure-cast
zinc levers
UL listed latch
standard
Wrought brass
or bronze roses
over steel
through-bolted
rose inserts
Conventional cylinders
or interchangeable core
keying compatible with
SFIC products from Falcon
or other manufacturers
Non-handed levers for
easy Þeld installation
3
LEVERS
Levers are solid pressure-cast zinc, finished to match mating parts. Roses are wrought brass or bronze installed over
steel through-bolted rose inserts. A spring-loaded retainer secures levers. Secure side retainer cannot be depressed
without a key that operates the lock.
Small Format
Interchangeable
Core (SFIC)
Dane shown
Thumbturn (interior)
Quantum shown
Plain
Conventional Cylinder
Dane shown
Quantum shown
Dane
Quantum
2-11/32”
~
~
2-11/32”
2-19/32”
2-19/32”
4-5/8”
4-5/8”
ø3-3/8”
ø3-3/8”
Abrasive Lever Options
All levers are available with an abrasive strip along the length of the lever to identify entrances to areas hazardous to the
disabled. To order add 6 (for example, 6DA for Dane lever or 6QU for Quantum lever) to the order number.
4
Catalog
Number
Description
ANSI
Number
and Grade
W101
Passage Latchset
Latch bolt by levers at all times.
W161
Communicating/Exit Latch
Deadlocking latch bolt by inside lever. Non-removable blank plate outside.
Inside lever is always free.
W201
Patio Lock
Deadlocking latch bolt by levers. Outside lever is locked by push button from
inside. Rotating inside lever or closing door releases button and unlocks outside
lever.
F77
W301
Privacy Lock
Latch bolt by levers. Outside lever is locked by push button on inside lever.
Rotating inside lever or closing door releases push button and frees outside lever. Inside lever is always free. Emergency release in outside lever unlocks door.
F76
W501
Entry Lock
Push button locking. Button on inside locks outside lever until unlocked by key
or by rotating inside lever. Closing door release push button and unlocks door.
Inside lever always free. Deadlock latchbolt.
F82
W511
Entry/OfÞce Lock
Deadlocking latch bolt by levers. Turn/push button locking. Pushing and turning button locks outside lever, requiring use of a key for unlocking the door until
button is manually unlocked. Pushing button locks outside lever until unlocked by
key or by rotating inside lever. Inside lever is always free.
F109
W561
Classroom Lock
Deadlocking latch bolt by levers. Outside lever is locked by key in outside lever.
Inside lever is always free.
F84
W581
Storeroom Lock
Deadlocking latch bolt by lever inside or key outside. Outside lever is always
locked. Inside lever is always free.
F86
W711
Apartment Entrance Lock
Deadlocking latch bolt by levers. Turn/push button locking. Pushing and turning
button locks outside lever, requiring use of a key for unlocking the door until button is manually unlocked. Pushing button locks outside lever until unlocked by
key, by rotating inside lever, or by closing the door. Inside lever is always free.
W12
Single Dummy Trim
Single trim, surface-mounted rigid lever.
F75
5
SC70 SERIES
F E AT U R E S A N D S P E C I F I C AT I O N S
SC70 Series
Falcon SC70 Series heavy duty closers are built for busy commercial applications that demand
reliable door control and easy maintenance. Designed for use with aluminum storefronts, SC70
Series closers are ANSI Grade 1, ADA compliant and deliver tough performance. Choose the SC70
for interior or exterior doors in retail shops, restaurants and small ofÞces.
Standard Features
¥ Meets ANSI A117.1
¥ ANSI/BHMA A156.4, Grade 1
¥ UL Listed
¥ 11/2Ó diameter piston
¥ Closer mounts hinge side, top jamb or parallel arm
when either the Rw/PA or Hw/PA arm is speciÞed.
¥ Adjustable sizes 1-6
¥ Single piece cast aluminum body
¥ Staked valves
¥ Non-handed for left or right swinging doors
¥ Fast and easy installation
¥ Separate adjustable general speed, latch speed
and backcheck
¥ Heat-treated forged steel piston
¥ Double heat-treated pinion
¥ Cover is high-impact UL Listed Þre retardant plastic
that meets UL 10C and UBC 7-2 (1997) Þre test
¥ UL 10C approved ßuid
¥ Universal screw pack
¥ 10-year warranty
Listings and CertiÞcations
The Falcon SC71 is UL approved and compliant with the UL 10C and UBC 7-2 (1997) Þre test. Additionally,
the SC71 is rated ANSI/BHMA A156.4, Grade 1 and designed to meet the American Disabilities Act (ADA) and
ANSI A117.1
SC70 Series Hinge (Pull Side)
To 100 o
101o to 120 o
121o to 150 o
151o to 180 o
13Ó - 330mm
12Ó - 305mm
10Ó - 254mm
9 1/2Ó- 241mm
To 100 o
101o to 120 o
121o to 150 o
151o to 180 o
6 15/16Ó- 176mm
5 15/16Ó- 125mm
3 15/16Ó- 100mm
3 7/16Ó - 87mm
Butt Hinges should not exceed 5Ó (127mm) in width.
Auxiliary Stop is recommended at hold-open point or where a door
cannot swing 180¡.
Reveal should not exceed 3/4Ó (19mm) for regular arm or hold-open arm.
Top Rail less than 3 7/8Ó (98mm) requires plate SC70-18.
Clearance of 2 1/8Ó (54mm) behind door required for 90¡ installation.
Delayed Action add sufÞx ÒDELÓ to selected cylinder (ex. SC70 DEL). Delays
closing from maximum opening to approx. 70¡, with adjustable delay time.
6
www.falcon.ingersollrand.com
Information in this catalog is subject to change without notice.
SC70 SERIES
ARCHITECTURAL DIAGRAMS
SC70 Series Heavy Duty (Parallel)
To 100 o
101o to 130 o
131o to 150 o
151o to 180 o
To 100 o
101o to 130 o
131o to 150 o
151o to 180 o
8 7/8Ó- 225mm
7 3/8Ó- 187mm
6 3/8Ó- 162mm
5 3/8Ó- 137mm
To 100 o
101o to 130 o
131o to 150 o
151o to 180 o
8 7/8Ó- 225mm
7 3/8Ó- 187mm
6 3/8Ó- 162mm
5 3/8Ó- 137mm
8 1/16Ó- 205mm
6 9/16Ó- 167mm
5 9/16Ó- 141mm
4 9/16Ó- 116mm
Auxiliary Stop is recommended at hold-open point, where a door cannot
swing 180¡, or where Dead Stop or Spring-n-Stop arm is not used.
Top Rail less than 6Ó (152mm) measured from stop requires plate SC70-18PA.
SC70 Series Dead Stop HO (Parallel)
To 100 o
101o to 130 o
131o to 150 o
151o to 180 o
8 1/16 Ó- 205mm
6 9/16 Ó- 167mm
5 9/16 Ó- 141mm
4 9/16 Ó- 116mm
Top Rail less than 6Ó (152mm) measured from stop requires plate SC70-18PA.
8
SC70 SERIES
ACCESSORIES
All SC70 Series closers come with full cover, standard arm and screw pack.
Arm Types
Regular Arm, SC70-3077PA
Non-handed arm with adjustable forearm
assembly to accommodate a range of doors
and frame reveal conditions. Mounts hinge
side, top jamb or parallel arm. PA shoe
included to allow installation in a parallel
arm conÞguration.
Dead Stop Hold-Open Arm, SC70-3049DS
Optional, non-handed, stamped, heavy duty, hold-open
parallel arm includes a positive mechanical stop and
non-adjustable forearm assembly for high volume trafÞc
or potentially abusive installation conditions. Also
includes a manually selective hold-open function.
Hold-Open Arm, SC70-3049PA
Optional, non-handed, hold open arm with
adjustable forearm assembly to accommodate
a range of doors and frame reveal conditions.
Mounts hinge side, top jamb or parallel arm. PA
shoe included to allow installation in a parallel
arm conÞguration.
Spring-n-Stop Arm, SC70-3077SS
Optional, non-handed, extra heavy-duty, forged parallel
arm includes an integral spring stop and non-adjustable
forearm assembly for high volume trafÞc or potentially
abusive installation conditions.
Heavy Duty Regular Arm, SC70-3077HD
Optional, non-handed, stamped, heavy duty,
parallel arm for use in high-trafÞc applications.
Spring-n-Stop Hold-Open Arm, SC70-3049SS
Optional, non-handed, extra heavy-duty, forged
parallel arm includes an integral spring stop and
non-adjustable forearm assembly for high volume
trafÞc or potentially abusive installation conditions.
Also includes a manually selective hold-open function.
Dead Stop Arm, SC70-3077DS
Optional, non-handed, stamped, heavy
duty, parallel arm includes a positive
mechanical stop and non-adjustable
forearm assembly for high volume trafÞc or
potentially abusive installation conditions.
Installation Accessories
SofÞt Shoe Support, SC70-30
Provides anchorage for Þfth screw used
with sofÞt shoe, where reveal is less than
3 1/16Ó (78mm).
Plate, SC70-18
Required for hinge side mount where top rail is less
than 3 7/8Ó (98mm). Required for top jamb mounting
where head frame is less than 3 7/8Ó (98mm).
Blade Stop Spacer, SC70-61
Required to lower parallel arm shoe to
clear 1/2Ó (13mm) blade stop.
Plate, SC70-18PA
Required for parallel arm mounting where top rail is
less than 6Ó (152 mm), measured from the stop.
Plate requires 1 3/4Ó (44mm) minimum top rail
measured from stop.
Auxiliary Shoe, SC70-62A
Requires a top rail of 7Ó (178mm). Optional
shoe replaces PA shoe for parallel arm
mounting of regular arm with overhead
holder/stop.
Cover, SC70-72
Standard, non-handed, full plastic cover encloses the
closer body.
9
SC80 SERIES
SC80 Series
Medium-duty applications like retail storefronts, cafes and clinics that need a closer that makes
door operation smooth and secure. The Falcon SC80 Series brings ANSI Grade 1 durability and
reliable performance to interior and exterior aluminum storefronts. An adjustable design ensures
ßexible installation and ADA compliance.
Standard Features
¥ UL Listed
¥ New for 2009 - adjustable sizes 1-6
and backcheck
¥ Heat-treated steel piston
¥ Heat-treated pinion
¥ Cover is high-impact UL Listed Þre retardant plastic
that meets UL 10C and UBC 7-2 (1997) Þre test
¥ 10-year warranty
The Falcon SC81 is UL approved and compliant with the UL 10C and UBC 7-2 (1997) Þre test. Additionally, the
SC81 is designed to meet the American Disabilities Act (ADA) and ANSI A117.1. The SC81 is ANSI/BHMA A156.4,
Grade 1 certiÞed.
To 120 o
11 3/4Ó- 298mm
121o to 180 o 8 1/2Ó - 216mm
To 120 o
5 5/16Ó- 135mm
121o to 180 o 2 15/16Ó- 75mm
Auxiliary Stop is recommended at hold-open point or where a door cannot
swing 180¡.
closing from maximum opening to approximately 70¡, with adjustable delay time.
10
SC80 SERIES
SC80 Series Heavy Duty (Parallel)
To 120o
8 3/4Ó- 222mm
121o to 180 o 6 3/4Ó- 171mm
To 120o
3 5/8Ó- 92mm
121o to 180 o 1 5/8Ó- 41mm
Auxiliary Stop is recommended at hold-open point, where a door cannot swing
180¡, or where Dead Stop or Spring-n-Stop arm is not used.
Top Rail less than 4 3/8Ó (111mm) measured from stop requires plate SC80-18PA.
SC80 Series Dead Stop HO (Parallel)
To 90o
10 1/8Ó- 257mm
91o to 110 o 7 5/8Ó- 194mm
To 90o
5 1/8Ó- 130mm
91o to 110 o 2 5/8Ó- 67mm
Top Rail less than 4 3/8Ó (111mm) measured from stop requires plate SC80-18PA.
12
SC80 SERIES
ACCESSORIES
All SC80 Series closers come with slim cover, standard arm and screw pack.
Arm Types
assembly to accommodate a range of doors and
frame reveal conditions. Mounts hinge side, top
jamb or parallel arm. PA shoe included to allow
installation in a parallel arm conÞguration.
Optional, non-handed, stamped, heavy duty, parallel arm
includes a positive mechanical stop and non-adjustable
Hold-Open Regular Arm, SC80-3049PA
adjustable forearm assembly to accommodate a range
of doors and frame reveal conditions. Mounts hinge
side, top jamb or parallel arm. PA shoe included to
allow installation in a parallel arm conÞguration.
Heavy Duty Arm, SC80-3077HD
abusive installation conditions. Also includes a manually
selective hold-open function.
3 1/16Ó (78mm).
clear 1/2Ó(13mm) blade stop.
Plate, SC80-18PA
Required for parallel arm mounting where top rail
is less than 4 3/8Ó (111 mm), measured from the
stop. Plate requires 1 7/8Ó (48mm) minimum top
rail measured from stop.
holder/stop.
Plate, SC80-18PAFC
Required for parallel arm mounting where top rail
is less than 4 3/8Ó (111mm), measured from the
stop. Plate requires 1 7/8Ó (48mm) minimum top rail
measured from stop. To be used with a full cover
SC80-72FC.
Plate, SC80-18
Required for top jamb mounting where head
frame is less than 1 3/4Ó (44mm) or ßush ceiling
conditions exists.
Cover, SC80-72
Standard, non-handed, slim line plastic cover
encloses the closer body with a cap on the unused
pinion shaft.
Plate, SC80-18FC
Required for top jamb mounting where head frame
is less than 1 3/4Ó (44mm) or ßush ceiling conditions
exist. To be used with a full cover SC80-72FC.
Cover, SC80-72FC
Optional non-handed, full plastic cover encloses the
closer body.
13
SC60 SERIES
SC60 Series
When you need a dependable closer for a light to medium-duty application, the Falcon SC60
Series gets the job done. Designed for interior use with an aluminum storefront, the SC60
Series offers ANSI Grade 1 durability backed by a ten-year warranty. Most common hole
pattern in the industry for versatile use and easy retroÞt.
Standard Features
¥ UL Listed
¥ Adjustable sizes 1-4 (SC61), 2-5 (SC60), and Þxed
sizes 4 & 5.
¥ Staked valves
and backcheck
¥ Heat-treated steel piston
¥ Heat-treated pinion
¥ 10-year warranty
The Falcon SC60 Series is UL approved and compliant with the UL 10C and UBC 7-2 (1997) Þre test. Additionally,
the SC61 is designed to meet the American Disabilities Act (ADA) and ANSI A117.1. The SC60 Series is
ANSI/BHMA A156.4, Grade 1 certiÞed.
To 120 o
11 13/16Ó- 300mm
121o to 180 o 8 1/4Ó - 210mm
To 120 o
5 9/16Ó- 141mm
121o to 180 o 2 9/16Ó- 65mm
Auxiliary Stop is recommended at hold-open point or where a door cannot
swing 180¡.
14
SC60 SERIES
ACCESSORIES
All SC60 Series closers come with standard arm and screw pack.
Arm Types
assembly to accommodate a range of doors
and frame reveal conditions. Mounts hinge
side, top jamb or parallel arm. PA shoe
included to allow installation in a parallel
arm conÞguration.
Hold-Open Arm, SC60-3049PA
adjustable forearm assembly to accommodate
a range of doors and frame reveal conditions.
Mounts hinge side, top jamb or parallel arm. PA
shoe included to allow installation in a parallel
arm conÞguration.
Optional, non-handed, extra heavy-duty, forged
parallel arm includes an integral spring stop and
non-adjustable forearm assembly for high volume
trafÞc or potentially abusive installation conditions.
Heavy Duty Regular Arm, SC60-3077HD
Optional, non-handed, stamped, heavy
duty, parallel arm includes a positive
mechanical stop and non-adjustable
forearm assembly for high volume trafÞc or
potentially abusive installation conditions.
abusive installation conditions. Also includes a manually
selective hold-open function.
3 1/16Ó (78mm).
Plate, SC60-18
Required for top jamb mounting where head frame
is less than 1 3/4Ó (44mm).
clear 1/2Ó(13mm) blade stop.
Plate, SC60-18PA
Required for parallel arm mounting where top rail is
less than 4 3/8Ó (111mm) for PA, 4 1/4Ó (108mm) for
HD and DS, measured from the stop. Plate requires
2 3/8Ó (60mm) minimum top rail measured from stop.
holder/stop.
Cover, SC60-72
Optional, non-handed, slim line plastic cover.
Available on SC60 and SC61 only.
17
24-R Series Rim Device
Non-Handed Rim Device 17-R Series
Panic Exit Hardware
The Falcon 24-R Series narrow stile rim device allows for application versatility in high-traffic installations. Standard features
include a single-point, rim type latch and a streamlined touch bar design. This device can also be electrified for maximum ease
of use and accessibility.
299 Strike
2789
Dogging Key
Specifications
Single Door Application
Door
Door
Min
Min Door
DeviceSizeStrikeStile (in)Opening Width
24-R
3’
299
264
1439
1606
31⁄2˝
33⁄8˝
21⁄4˝
23⁄4˝
2’ 73⁄8˝
2’ 71⁄4˝
2’ 61⁄2˝
2’ 71⁄8˝
24-R
4’
299
264
1439
1606
31⁄2˝
33⁄8˝
21⁄4˝
23⁄4˝
3’ 13⁄8˝
2’ 71⁄4˝
3’ 1⁄2˝
3’ 11⁄8˝
24-R
3’
299 x 2923
299 x 4023
264 x 2923
264 x 4023
1439 x 2923
1439 x 4023
1606 x 2923
1606 x 4023
4396 x 4423
31⁄2˝
4˝
33⁄8˝
35⁄8˝
31⁄2˝
33⁄4˝
31⁄2˝
33⁄4˝
21⁄8˝
2’ 71⁄2˝
2’ 73⁄4˝
2’ 73⁄8˝
2’ 73⁄4˝
2’ 71⁄8˝
2’ 73⁄8˝
2’ 71⁄4˝
2’ 71⁄2˝
2’ 61⁄2˝
24-R
4’
299 x 2923
299 x 4023
264 x 2923
264 x 4023
1439 x 2923
1439 x 4023
1606 x 2923
1606 x 4023
4396 x 4423
31⁄2˝
4˝
33⁄8˝
35⁄8˝
31⁄2˝
33⁄4˝
31⁄2˝
33⁄4˝
21⁄8˝
3’ 11⁄2˝
3’ 13⁄4˝
3’ 13⁄8˝
3’ 13⁄4˝
3’ 11⁄8˝
3’ 13⁄8˝
3’ 11⁄4˝
3’ 11⁄2˝
3’ 1⁄2˝
20
Hand: Non-handed.
Functions:24-EO (Exit Only) has all functions built in. Order trim with the
device, or add it later. See Trim Selection Chart on page 29.
Finishes: US3 (605); US4 (606); US10 (612); US26 (625);
US26D (626); US32 (629); US32D (630); US28 (628), 313AN.
(See page 29 for finishes.)
Strikes: 299 strike standard. See page 27 for optional strikes.
Latchbolt: Stainless steel, 3⁄4” throw.
Deadlocking Latchbolt: Optional. Specify “DL” prefix.
Dogging Feature: 1⁄2 turn hex dogging standard. No threaded parts to wear out.
Cylinder Dogging: Specify “CD” prefix. Uses 11⁄8” long mortise cylinder with
standard cam.
Double Door Application
DoorStrike x
Min
Min Door
DeviceSize
MullionStile (in)Opening Width
Cylinder Dogging
Stock Sizes: See chart to left.
Doors:13⁄4” thick, wood or metal. Specify thickness if other than 1 3⁄4”.
Projection: 23⁄4” maximum, 2” dogged.
Mounting Height: 40” from CL to finished floor.
Electric Function: Can be interfaced with building security systems. Latch retraction,
security monitoring, electric dogging, delayed egress and exit alarm
available (EL and ED fail- secure only). Subject to code requirements,
state and local. (See pages 33-41 for details.)
Fasteners: All mounting screws are concealed.
Sex Bolts: Recommended when device is used with hollow core wood, composite
or light gauge hollow metal doors. For EO device, specify 4 - 425
(#I0-24) SNB and 2 - 325 (1⁄4-20) SNB. For devices with trim, specify
4 - 425 (#I0-24) SNB.
ANSI: Certified ANSI A156.3-2001 Grade 1 standards.
Center Case & Working Parts:Wrought steel with heavy wrought and sintered metal parts.
Shim Kit: For glass lite applications; 1⁄4”thick, specify SK24-R.
24 series Trim Designs
Trim Designs
Lever Trims (712L)
Lever Designs
712L
712L/NL
712L/DT
712L/BE
Projection: 21⁄4”, Dane
213⁄16”, Sutro
31⁄8”, Quantum
Pull Trims (710)
Dane
Quantum
Projection: 21⁄4˝
Projection: 3 1⁄ 8˝
Dane, Quantum and Sutro levers return to within 1⁄2” of door.
Knob Trim (711K)
711K
711-NL
710DT
710TP
Sutro
Projection: 213 ⁄16˝
Athena (715)
711K-DT
K-BE
710NL
715DT
Grip overall: 9”
Width: 15⁄8”
Pull: 61⁄4” C x C
Projection: 21⁄4”
Delta Trims
1 1⁄8” mortise cylinder
719TL
719TLP
718TP
Specify Handing
All Delta pulls: 61⁄4” C x C
All Delta pulls: 2” projection
TLP, NL, TP & DT: 13” overall length
TL: 71⁄4” L x 13⁄4” W x 13⁄4” projection
28
1” cylinder
718DT
718C
718NL
717DT
Brass, Stainless and/or Plated finishes.
For cylinder information see page 14. When
locking function is not required, specify trim by
(BE) blank escutcheon.
25-R Series Rim Device
Panic Exit Hardware
The Falcon 25-R Series rim device meets the demanding requirements of high traffic installations with a single-point, rim type
latch and a streamlined touch bar design. This device can also be electrified for maximum ease of use and accessibility.
2789
Dogging Key
299 Strike
Cylinder Dogging
Door
Door
Min
Min Door
25-R
3’
299
264
1439
1606
4”
37⁄8˝
31⁄4˝
35⁄8˝
2’ 71⁄2˝
2’ 73⁄8˝
2’ 61⁄2˝
2’ 7˝
25-R
4’
299
264
1439
1606
4˝
37⁄8˝
31⁄4˝
35⁄8˝
3’ 11⁄2˝
3’ 13⁄8˝
3’ 1⁄2˝
3’ 1”
DoorStrike x
Min
Min Door
DeviceSize
25-R
3’
25-R
4’
6
299 x 2923
299 x 4023
264 x 2923
264 x 4023
1439 x 2923
1439 x 4023
1606 x 2923
1606 x 4023
41⁄8˝
43⁄8˝
4˝
41⁄4˝
37⁄8˝
41⁄8˝
41⁄4˝
41⁄2˝
1
2’ 75⁄8˝
2’ 77⁄8˝
2’ 71⁄2˝
2’ 73⁄4˝
2’ 73⁄8˝
2’ 75⁄8˝
2’ 71⁄4˝
2’ 71⁄2˝
Specifications
Strikes: Latchbolt: Deadlocking Latchbolt: 4 ⁄8˝
43⁄8˝
4˝
41⁄4˝
37⁄8˝
41⁄8˝
41⁄4˝
41⁄2˝
3’ 1 ⁄8˝
3’ 17⁄8˝
3’ 11⁄2˝
3’ 13⁄4˝
3’ 13⁄8˝
3’ 15⁄8˝
3’ 11⁄4˝
3’ 11⁄2˝
25-V x 25-R
3’
1609
23⁄8˝
2’ 73⁄4˝
25-V x 25-R
4’
1609
23⁄8˝
3’ 13⁄4˝
Non-handed.
299 strike standard. See page 15 for additional info.
Stainless steel, 3⁄4˝ throw.
Standard.
Dogging Feature: 1⁄2 turn hex dogging standard. No threaded parts to wear out.
Cylinder Dogging: Specify “CD” prefix. Uses 1-1⁄ 8˝ long mortise cylinder with
standard cam.
Stock Sizes: See chart to left. Cut to size in the field.
Doors: 1-3⁄4˝ thick, wood or metal. Specify thickness if other than 1-3⁄4˝.
23⁄4˝ maximum, 2” dogged.
Projection: Mounting Height: Electric Function: Can be interfaced with building security systems. Latch retraction,
FSA/FSE trim, security monitoring, electric dogging, delayed egress
and exit alarm available (EL and ED fail-secure only). Subject to
code requirements, state and local. (See pages 33-41 for details).
Fasteners: All mounting screws are concealed, sheet metal screws and machine
screws standard.
5
299 x 2923
299 x 4023
264 x 2923
264 x 4023
1439 x 2923
1439 x 4023
1606 x 2923
1606 x 4023
Hand:
Finishes: US3 (605); US4 (606); US10 (612); US26 (625); US26D (626);
US32 (629); US32D (630); US28 (628), 313AN.
401⁄4˝ from CL to finished floor.
Sex Bolts:
Recommended when device is used with hollow core wood, composite or light gauge hollow metal doors. For EO device, specify 8 - 425 (#I0-24) SNB. For devices with trim, specify 2 - 425 (#IO-24) SNB.
Certified ANSI A156.3-2001 Grade 1 standards.
ANSI: Center Case & Working Parts: Center case is heavy wrought and sintered metal parts.
Shim Kit: For glass lite applications; 1⁄4˝ thick, specify SK25-RM.
579 Strike Retrofit Kit: Consult factory.
25 series Trim Designs
Functionality built into the trim, facilitating easy door preps, easy field retrofit and easy ordering.
Lever Trims (510L)
Lever Designs
Dane
Quantum
Projection: 2 ⁄16˝
13
510L
510L-NL
510L-DT
510L-BE
Projection: 21⁄4”, Dane
213⁄16”, Sutro
31⁄8”, Quantum
Vandal-Resistant Lever Trims (511L)
Projection: 3 ⁄ 2˝
1
Sutro
Projection: 3 13 ⁄16˝
Lever: 4 5⁄8˝ escutcheon: 2 3⁄4˝ x 9 3⁄4˝ (specify handing) brass and stainless finishes.
Protected by easily replaceable shear pin.
Lever is reversible, supplied RHR if not specified. For keyed functions, see page 14
for cylinder requirements.
Provides resistance to rotation, making damage of trim due to attack from the outside less likely. Designed to operate normally after vandalism
attempts without the need for maintenance personnel intervention.
•Heavy duty, vandal-resistant, ANSI AI56.3 Grade 1 security trim
•Lever deflects up to 22 ft-lb for a minimum of 10,000
vandal-resistant cycles
•Vandal resistance is present in both lever rotation directions
•After lever is fully deflected, lever stops rotating and a shear
pin breaks at 70 ft-lb to prevent damage to unit
Pull Trims (512TP)
•Available on 25 rim, vertical, mortise, and concealed devices
•Retrofits all existing 25 trim without additional door prep
•LK monitor switch is available
•Works with all electric lock and unlock functions
•Available in all finishes and designs including Dane, Quantum and Sutro
Knob Trims (513K)
Cylinder Only
(NL-OP)
Delta (717)
513K-DT 513K
513K-BE 513K-NL
717DT
512TP
512NL
Escutcheon: 23⁄4˝ x 16˝
Grip: 61⁄4˝ C–C
Brass and Stainless Steel
For keyed functions, see page
14 for cylinder requirements.
16
512DT
512TP-BE
Round Ball Knob
Escutcheon: 23⁄4˝ x 93⁄4˝
Brass and Stainless Steel
For keyed functions, see page
14 for cylinder requirements.
Key retracts latch bolt.
Cylinder sold separately
(see page 14).
F-25-R Series Rim Device
ZFire Exit Hardware
The Falcon F-25-R Series rim device combines sleek styling and durability with the protection of a fire-rated device.
The F-25-R also features a single-point, rim type latch and can be electrified.
299F Strike
Door
Door
Min
Min Door
F-25-R
3’
299-F
4”
2’ 71⁄2˝
F-25-R
4’
299-F
4”
3’ 11⁄2˝
DoorStrike x
Min
Min Door
DeviceSize
F-25-R
3’
299-F x F-4023
499-F x F-4023
43⁄8˝
41⁄2˝
2’ 77⁄8˝
2’ 77⁄8˝
F-25-R
4’
299-F x F-4023
499-F x F-4023
43⁄8˝
41⁄2˝
3’ 17⁄8˝
3’ 17⁄8˝
Specifications
Hand:
Non-handed.
UL: “A” label (3 hr.); 4´0˝ x 8´0˝; 8´0˝ x 8´0˝ with F-4023 mullion.
“B” label (11⁄2 hr.); 8´0˝ x 8´0˝; with KRF4023.
Finishes: US3 (605); US4 (606); US10 (612); US26 (625); US26D (626);
US32 (629); US32D (630); US28 (628), 313AN.
Strikes: Latchbolt: Deadlocking Latchbolt: Stock Sizes: 299F strike standard
499F with mullion optional
Stainless steel, 3⁄4˝ throw.
Standard.
See chart to left. Cut to size in the field.
Doors: 1 3⁄4˝ thick, wood or metal. Specify thickness if other than 13⁄4˝.
2 3⁄4˝ maximum.
Projection: Mounting Height: Electric Function:Can be interfaced with building security systems. Latch
retraction, FSA/FSE trim, security monitoring, electric dogging,
delayed egress and exit alarm available (EL and ED fail- secure
only). Subject to code requirements, state and local. (See pages
33-41 for details).
40 1⁄4˝ from CL to finished floor.
Fasteners: All mounting screws are concealed, sheet metal screws and machine
screws standard.
Sex Bolts: Required for use in EO applications when used with wood,
composite or non-reinforced hollow metal doors. For EO device,
specify 8 - 425 (#10-24) SNB. For devices with trim, specify 2 - 425
(#10-24) SNB.
ANSI: Certified ANSI A156.3-2001 Grade 1 standards.
Center Case & Working Parts: Center case is heavy wrought and sintered metal parts.
Shim Kit: For glass lite applications; 1⁄4˝ thick, specify SK25-RM.
7
100 Series Concealed Overhead Door Holders/Stops
Materials and Finishes:
In Heavy Gauge Brass or 300 Series Stainless Steel, these models
offer the broadest range of finishes in the industry, complementing
any design and offering the highest resistance to corrosion.
Available in the following finishes:
100 Series Heavy-Duty
Glynn-Johnson offers a complete line of overhead door holders and
stops, accommodating virtually all openings with solutions for even
the most complex door control problems. These concealed holders
and stops provide the most attractive and reliable heavy-duty door
control available.
Glynn-Johnson 100 series holders and stops provide the most reliable and versatile concealed overhead door control. They are
designed for installation on virtually all types of doors mounted on
conventional type butt hinges, pivots, continuous hinges, swing
clear hinges and numerous other specialty hinges. When used in
conjunction with many surface-applied door closers, 100 series
holders and stops provide the most effective control for entrance
doors and vestibule doors of all types, as well as heavy or often
used interior doors. Templates provided allow for variable mounting
positions, ranging from 85° - 110° of opening.
Five Models:
• 100H Series Hold-Open Model
• 100HP Series Internal Hold-Open Model
• 100F Series Friction Hold-Open Model
• 100S Series Stop-Only Model
• 100SE Series Special Stop-Only Model
Six Sizes:
• Each model comes in six sizes.
• Simple
• Standardized
Three Options:
• ADJ—Adjustable Jamb Bracket
• CJ—Jamb Bracket for use with LCN5030 Closer
• SOC—Pin-in-Socket Security Screw Package
Unmatched Convenience:
• Non-handed
• Improved Compatibility with Door Closers
• Single/Double-Acting Doors
• Interior/Exterior Applications
• Reduced Door Prep
• Durable
• Improved Corrosion Resistance
• Function Conversion Kits are Available.
18
Finishes
US3
US4
US10
US10B
US32
US32D
SP4
SP10
SP28
SP313
SPBLK
Description
Polished Brass
Satin Brass
Satin Bronze
Oil Rubbed Bronze
Polished Stainless Steel
Satin Stainless Steel
Powder Coat Brass
Powder Coat Bronze
Powder Coat Aluminum
Powder Coat Dark Bronze
Powder Coat Black
Models
These models provide a wide range of optional features, and are
ideal for use on entrance and vestibule doors, large doors, doors
opened frequently, or doors subject to abuse. These models are also
furnished with an offset-style jamb bracket.
Designed for heavy-duty applications, 100 series models will
provide long-lasting protection to doors, frames, hinges, related
hardware and surrounding walls or obstructions.
100H Series Hold-Open
(Suffix H) The Hold-Open function should be used where it
is desired to hold a door open at a predetermined position for
short or long periods of time, permitting an unobstructed
traffic flow through the opening.
These models are both selective and adjustable, featuring the
most reliable Hold-Open mechanism available. They feature
a control knob which protrudes from the face of the door and
turns the Hold-Open function on or off. Set in the inactive
position, the unit acts as a stop and shock absorber. The tension
on the Hold-Open mechanism can be adjusted using an allen
wrench to offset air currents or other exterior conditions. The
Hold-Open tension adjustment is located in the bottom of the
track in the top of the door.
100HP Series Internal Hold-Open
These models provide a Hold-Open unit with the Hold-Open
mechanism built into the channel, thus reducing the door prep.
The 100HP have a preset Hold-Open force that is not adjustable.
The Hold-Open feature is not selectable in these units, so the doors
are always held open.
100F Series Friction Hold-Open
(Suffix F) Friction Hold-Open models provide an alternative
holding method, ideal for heavy patient room doors, closet
doors or similar applications where multiple Hold-Open
positions are desired. The friction tension is adjusted using
an allen wrench and an open end wrench. The friction tension
adjustment is located on the top of the slider in the channel.
100S Series Stop-Only
(Suffix S) When the Hold-Open function is not required, the
Stop-Only function provides the same effective door control
minus the Hold-Open feature. The Stop-Only model may be
used on fire doors.
100SE Series Special Stop-Only
(Suffix SE) When Stop-Only models are used in conjunction with
single point Hold-Open electronic door closers, they may be ordered
without the shock-absorbing mechanism. Used as an auxiliary stop
with these closers, they will prolong the life of the closer. The stop
location is adjusted using an allen wrench on the stop block located
in the channel.
Note: Caution should be used when using this option in other applications,
as the elimination of the shock-absorbing spring can put added stress on door
and frame if used improperly.
Application Information
UL Classification
The 100 series Stop-Only models are classified by Underwriters
Laboratories (UL) as Miscellaneous Fire Door Accessories. This
classification applies to use on either Hollow Metal Fire Doors or
Wood Fire Doors. Where Wood Door manufacturer’s listing allows
for the cutout required for installation, concealed overhead stops
may be used on those wood fire doors. These units may be used on
doors of any rating. As a reminder, the Miscellaneous Fire Door
Accessories (GVUX) section is defined by UL as: “Miscellaneous
fire door accessories are intended in the individual Listings. The
accessories have been investigated to determine that when installed
in accordance with the manufacturer’s instructions, the accessories
do not adversely affect the fire rating of the fire door and/or fire
door frames.”
Dead Stop Templating:
If a wall or similar obstruction is in place at 110° or less opening
angle (i.e. doors that open back-to-back), Dead Stop Templating
should be used. This includes all Hold-Open, Friction and
Stop-Only models, except when the “SE” Option is used. The
Dead Stop position is reached when the shock-absorbing spring
is fully compressed, the initial degree of opening will be 5° to 7°
less than the Dead Stop opening.
Example: If the holder is templated to 100° Dead Stop, the door will hold open
somewhere between 93° and 95°, but no further than 100°.
Note: Do not use dead-stop templating on the 100SE Series since there is no
shock-absorbing spring.
Environmental Considerations:
Environmental factors should always be considered when
specifying overhead holders and stops. Doors that are positioned
on a building’s exterior or subject to corrosive conditions should
be equipped with a holder constructed primarily of stainless steel
or brass materials. For interior applications, steel is acceptable,
though brass substrates generally provide a more attractive
architectural-grade finish.
Function Conversion Kits
• FK100F—Converts a 100H or 100S unit into a 100F unit.
To order specify FK100F.
• FK100H—Converts a 100F or 100S unit into a 100H unit.
To order specify FK100H.
• No kit is needed to convert a 100H or 100F unit
into a 100S unit.
Options
Suffix ADJ (Adjustable Jamb Bracket):
An additional option on the 100 series is the adjustable jamb bracket,
which allows the degree of Hold-Open or Stop angle to be adjusted
after installation. Suffix “ADJ” is available in all functions, but only
in sizes 3, 4, 5 & 6. ADJ jamb bracket requires additional frame prep.
The ADJ option cannot be added to an existing unit, it must be
factory ordered.
Suffix CJ (Closer Jamb Bracket):
Provides a special jamb bracket needed for 100 series units used with
LCN5030 closers. These special jamb brackets are handed, so handing
will need to be specified when ordering the “CJ” option, CJLH for
a left hand door and CJRH for a right hand door. The CJ option
cannot be added to an existing unit, it must be factory ordered.
Suffix SOC (Pin-in-Socket Security Screw Package):
A screw package with pin-in-socket screws for mounting the jamb
bracket to the frame is provided instead of the standard screw package.
19
100 Series Concealed Overhead Door Holders/Stops
1/4"
3/4"
2"
1"
1-1/4"
1"
1-1/4"
4-1/4"
3/4"
1-1/4"
1/4"
1/4"
1"
3/8"
2-3/8"
5-1/2"
3-1/2"
12"
1/2"
1-1/4"
3/8"
100 Series Sizing Chart
BUTTS/OFFSET PIVOTS
SIZE
1
2
3
4
5
6
DOOR
OPENING
18"–23"
23-1/16"–27"
27-1/16"–33"
33-1/16"–39"
39-1/16"–45"
45-1/16"–54"
STOP
ONLY
101S*
102S*
103S
104S
105S
106S
HOLD
OPEN FRICTION
101H*
101F*
102H*
102F*
103H
103F
104H
104F
105H
105F
106H
106F
CENTER HUNG
DOOR
OPENING
--------33-1/16"–39"
39-1/16"–45"
45-1/16"–51"
51-1/16"–59"
STOP
ONLY
-------103S
104S
105S
106S
HOLD
OPEN FRICTION
--------------103H
103F
104H
104F
105H
105F
106H
106F
Note: This chart illustrates the most common types of hinging and door opening sizes.
For unusual door details, contact Glynn-Johnson for availability.
*These sizes are not available for use with offset pivots. Also not available with the ADJ option.
The template information on this page is for reference only and is not intended to serve as an installation template.
For complete dimensional information, refer to Glynn-Johnson template book.
20
BHMA/ANSI, A156.8 & FED. Spec. Cross Reference
G-J Model
BHMA*
FED. Spec.
101-106 H
C01511
1160
101-106 S
C01541
---101-106 F
C01531
---* First numeral (0) designates optional material.
To specify:
Brass material, change 0 to 1 (i.e. C11511)
Stainless Steel material, change 0 to 5 (i.e. C51511)
BHMA
All 100 series models are designed for heavy-duty
applications and far exceed BHMA cycle test and
force test requirements for Grade 1 holders and stops.
7226 & 7226F 3/4" Offset
7226 or 7226F Pivot Sets
7226 Pivot Set
• Non-handed 3/4" offset pivot set consisting of a base plate7226F Pivot Set
mounted 7226 or 7226F Bottom Pivot, and a head frame
mounted 7226 or 7226F Top Pivot.
• Door Thickness minimum 1-3/4" (44mm), bevel
1/8" (3mm) in 2" (51mm).
• Center Line Offset 3/4" (19mm) from face of door
and 3/4" from edge of door.
• Maximum Load 600 pounds (272 kg).
• UL Listed
7226 for 20 minute rated door.
7226F for 3 hour rated door.
• 7226F meets ANSI/BHMA Grade 1.
• Vertical Adjustment Range of 3/16" (5mm),
which includes a positive locking feature.
• Optional Intermediate Pivot
For 7226 set, use 7226 Intermediate Pivot
(handed). For 7226F set, use 7226F Intermediate
Pivot (handed). Each Intermediate Pivot carries up
to an additional 100 pounds (45.5 kg) load or needed
for doors over 7'. See page 42.
• Optional 7226 PT Power Transfer Intermediate Pivot
(handed). Provides 4 wire transfer with no weight
bearing capabilities. See page 48.
How to Order:
7226 ___ - ___ - ___ - ___
Rating:
Blank
F
Non-fire-rated
Fire-rated
Pivot Style:
Blank Top and bottom set
TOP
Top pivot only
BTM
Bottom pivot only
INT
Intermediate pivot only
PT INT Power transfer intermediate pivot only
Finishes:
Non-Fire-Rated
Fire-Rated
P I V O T S
Handing:
LH
Left-hand door
RH
Right-hand door
US3, US4, US10, US10B, US26, US26D, SP4, SP10, SP28, SP313, SPBLK
US3, US10, US32, US32D, SP4, SP10, SP28, SP313, SPBLK
36
7200 Series Pivots - Overview
3/4" Offset Pivots - 200 Lb. Doors
7212-7215-7222-7226-7227 Top Pivot
7212 PIVOT SET
7212V Top Pivot
Optional
7222 PIVOT SET
7212V PIVOT SET
7212-7212V-7222
Intermediate Pivot
7212
Bottom Pivot
7222
Bottom Pivot
7212
Bottom Pivot
3/4" Offset Pivots - Standard and Fire-Rated - 500 to 700 Lb. Doors
Optional
7212-7215-7222-7226-7227 Top Pivot
7215F-7226F-7227F Top Pivot
7215 OR 7215F
PIVOT SET
7226 OR 7226F
PIVOT SET
7215 Bottom Pivot
7215F Bottom Pivot
7226-Bottom Pivot
7226F-Bottom Pivot
7227 OR 7227F
PIVOT SET
7215-7226-7227
Intermediate Pivot
7215F-7226F-7227F
Intermediate Pivot
7227-7227F-Bottom Pivot
7215-7226-7227PT
Power Transfer
Intermediate Pivot
3/4" Offset Pivots - Fire-Rated - 1000 to 1750 Lb. Doors
Optional
7230F-7237F Top Pivot
7230F
PIVOT SET
7237F
PIVOT SET
7230F-7237F
Intermediate Pivot
7230F
Bottom Pivot
B2
7237F
Bottom Pivot
Wall Bumpers
WS406CVX & WS407CVX
WS406CCV & WS407CCV
Features:
• Constructed in sturdy yet economical wrought base of brass, aluminum or stainless
steel construction.
• Feature concealed tamper-proof mounting.
• Shipped factory preassembled backplate to reduce installation cost.
• Easy installation by inserting screwdriver through small hole in rubber.
• The WS406CVX unit is designed with a convex rubber bumper, packed with wood screw and
plastic anchor.
WS406CVX & WS407CVX
• The WS406CCV unit is designed with a concave rubber bumper, which avoids damage to
locks with projecting buttons, packed with wood screw and plastic anchor.
• The WS407CVX unit is designed with a convex rubber bumper packed with screw and
drywall anchor.
• The WS407CCV unit is designed with a concave rubber bumper which avoids damage to
locks with projecting buttons and is packed with screw and drywall anchor.
• WS406CVX & WS407CVX meets ANSI/BHMA 156.16 L22201 for brass, L42101 for
aluminum and L52101 for stainless steel.
• WS406CCV &WS407CCV meets ANSI/BHMA 156.16 L22251 for brass and L42251 for
aluminum, and L52251 for stainless steel.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28, US32D.
Product No.
WS406CVX
WS406CCV
WS407CVX
WS407CCV
D14
Mounting
Hardware
Wood screw,
plastic anchor
Wood screw,
plastic anchor
Screw, Drywall
Anchor
Screw, Drywall
Anchor
Base
Diameter
Base
Thickness
Overall
Projection
2-1/2"
3/8"
1"
2-1/2"
3/8"
1"
2-1/2"
3/8"
1"
2-1/2"
3/8"
1"
WS406CCV & WS407CCV
Door Silencers
SR64
SR65
SR66
Features:
Features:
Features:
• For use on metal frames featuring
pneumatic design that, once installed,
forms an air pocket to absorb shock
and reduce noise of door closing.
• For use on wood frames, also feature
pneumatic design to cushion shock and
absorb noise.
• Self Adhesive Rubber Silencers.
• To prevent removal, a small brad should
be driven into stop strip and through
stem of silencer, as shown in the detail.
• Packed in sheets of 100.
• Tamper-proof once installed on the frame.
• Proper installation also eliminates door
rattle and provides constant tension for
door latches or locks.
• Packed in bags of 100. Grey also available
in bulk pack of 2500.
• Economical installation requires no
drilling of frames.
• Finishes: brown, grey, white.
• Packed in bags of 100.
• Meets ANSI/BHMA 156.16, L03021
• Finish: grey.
• Each bag has an installation tool included.
• Meets ANSI/BHMA 156.16, L03011.
• Finish: grey is standard. Black optional.
Product No.
Diameter
Thickness
Product No. Height
Width
Thickness
Product No.
Diameter
Thickness
SR64
1/2"
1/8"
SR64
3/8"
1/8"
SR66
1/2"
1/8"
3/4"
D21
Residential Door Stops
060 and 061 Flexible Door Stops
Features:
• Utilizes heavy gauge spring to maintain rigid protections.
• Simple to install - only a screwdriver required.
• Rubber tip is replaceable.
• Made from burnished wrought steel.
• Meets design requirements of ANSI/BHMA A156.16.
• Packed disassembled for quick installation.
• Finishes: F3, F5, F10, F10B, F14, F26, F26D.
Product Number
Projection
060
061
3"
4"
060
061
60, 61 and 62 Base Door Stops
Features:
• Available in three sizes to accommodate varying areas of installation and door
trim dimensions.
60 Base Door Stop
• Projection: 3-3/4".
• Made from solid brass or aluminum.
• Finishes: B3 (B-605), B4, B5, B10, B10B (B-613), B14, B15 (B-619), B15A
(B-620), B26 (B-625), B26D, A3, A4, A5, A10, A10B, A14, A26, A92.
61 Base Door Stop
• Projection: 3-1/8" on brass units. 3-3/16" on aluminum units.
• Made from solid brass, aluminum, or epoxy colored aluminum.
(B-620), B26 (B-625), B26D, A3, A4, A5, A10, A10B, A14, A26, A92, A-A
(Almond Epoxy Coated), A-W (White Epoxy Coated), A-BLK (Black Epoxy
Coated).
62 Base Door Stop
• Projection: 4-1/2".
(B-620), B26 (B-625), B26D, A3, A4, A5, A10, A10B, A14, A26, A92.
062 Base Door Stop
Features:
• Base Door Stop features one-piece styling.
• Designed with a flat surface to accommodate wrench or pliers when
installing.
• Meets ANSI/BHMA A156.16.
(B-620), B26 (B-625), B26D, A3, A4, A5, A10, A10B, A14, A26, A92.
Product Number
Projection
062
2-1/2"
D22
60
61
Viewers
One-Way Viewer
B
Pulls & Plates
Meets ANSI/BHMA A156.16 L23222
UL Listed 90 minute fire doors
150° Angle of View.
For doors 1-3/8" to 2-1/16" thick.
Secure, tamper-resistant.
Solid brass body; glass lens.
Simple installation — only a 1/2" hole required.
Suggested installation height: 60" from floor.
Trim washer available, 3/4" x .032" thick.
A
•
•
•
•
•
•
•
Hinges & Pivots
U696
Finishes
Ives Number
B4
B10B
B26D
BHMA
606
613
626
C
Flush Bolts & Coordinators
One-Way Wide Angle Viewer
B3
B15**
B26D
BHMA
605
619
626
E
Finishes
Ives Number
Stops
698 meets ANSI/BHMA A156.16 L23172
U698 meets ANSI/BHMA A156.16 L23222
U698 is UL Listed 90 minute fire doors
190° Angle of View.
Lens projects 1/4" from face of door.
4 optical glass lenses.
For doors 1-3/8" to 2-1/8" thick.
Solid brass body and barrel.
Simple installation — only a 9/16" hole required.
Suggested installation height: 60" from floor.
D
•
•
•
•
•
•
•
Latches, Catches & Bolts
698
U698
B716*
* not available on U698
** only available in Schlage Carded
F5
Exterior Hardware
G
Miscellaneous Hardware
USA 1.877.613.8766
Canada 1.905.403.1800
www.ives.ingersollrand.com
F5
Roller Latches
RL30
• Actuation is simple, closing of the door causes the
roller to fall in the depression of the strike, thereby
holding the door closed.
• The projection of the roller is easily adjusted using
adjusting screws on the face of the unit.
• Maximum projection of the roller is 3/8" allowing for
variance in the door clearance.
• Nylon Roller Standard.
• Forged Brass Construction.
• Meets ANSI/BHMA A156.16, E19091.
• Finishes: US3, US4, US10, US10B, US26, US26D.
• Optional Roller—F— Nylon covered brass roller.
• Optional Strike—A—ASA
Dimensions:
Body: 1" Wide x 3-3/8" Long x 1-11/16" Deep
Strike: 1-11/16" Wide x 2-1/4" Long x 5/32" Thick
Optional ASA Strike: STK726 (not shown): 1-1/4" wide x 4-7/8"
long x 3/32" thick
RL32
• Actuation is simple, closing of the door causes the
roller to fall in the depression of the strike, thereby
holding the door closed.
• The projection of the roller is easily adjusted by turning
knurled knob on back of latch.
• Maximum projection of the roller is 1/2" allowing for
variance in the door clearance.
• Fits heavy-duty cylindrical lock cutout.
• Nylon Roller Standard.
• Non-handed.
• Brass or Stainless Steel Construction.
• Meets ANSI/BHMA A156.16, E19101.
• Finishes: US3, US4, US10, US10B, US32, US32D.
• Optional Roller—F— Nylon covered brass roller.
• Optional Strike—A—ASA.
Dimensions:
Body: 1-1/8" Wide x 2-1/4" Long x 2-1/4" Deep
Strike: 1-1/8" Wide x 2-3/4" Long x 3/32" Thick
Optional ASA Strike: STK726 (not shown): 1-1/4" wide x 4-7/8"
long x 3/32" thick
How to Order:
RL ____ ____ ____ - ____
Model:
30
32
Roller Type:
Blank
Standard Nylon Roller
F
Nylon Coated Brass Roller
Strike Type:
Blank
Standard Strike
A
ASA Strike
Finishes:
RL30
RL32
US3, US4, US10, US10B, US26, US26D
US3, US4, US10, US10B, US32, US32D
G1
Cabinet/Closet Knobs and Pulls
22 Flush Pull
• Low profile makes this pull ideal for louvered, bi-folding or wardrobe
doors.
• Extra deep recess and reverse tapered grip provide for ease of
pulling and gripping.
• Made from wrought brass.
• Conforms to design requirements of ANSI/BHMA A156.9 B22201
and A156.14 D2781.
• Finishes: B3, B4, B5, B10, B10B, B14, B15 (B-619), B15A (B-620),
B19, B26 (B-625), B26D, B-619, B-620, B-625.
Dimensions:
1-5/16" H x 3-1/8" W x 7/16" D
218 Finger Pull
• Ideal for use on sliding doors.
• Easy installation.
and A156.14 D2781.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
Dimensions:
Inside Cup Diameter: 3/4"
Overall Diameter: 1"
Depth: 5/16"
220/221 Flush Pull
• Built-in prong design eliminates the need for screws or brads and
facilitates installation.
• Packed with two escutcheon pins for added holding power.
and A156.14 D2781.
Dimensions:
220 Inside Cup Diameter: 2"
220 Overall Diameter: 2-3/8"
220 Depth: 7/16"
221 Inside Cup Diameter: 2-1/8"
221 Depth: 7/16"
K5
Cabinet/Closet Knobs and Pulls
425/426 Flush Ring Pull
• Convenient finger grip provides easy use of pull.
• Conforms to design requirements of ANSI/BHMA A156.9 B22201.
Dimensions:
425 Depth: 3/8"
426 Depth: 3/8"
42 Pocket Sliding Door Bolt
• Exclusive Ives design permits emergency release of bolt from outside the
door.
• Spring activated design allows feather-touch action.
• Brass grommet supplied to cap release hole, protecting the door’s finish.
Dimensions:
Overall Size, Plate: 3-1/16" x 1-5/32"
Strike: 1" x 3/4"
Depth of Mortise: 5/8"
230 Sliding Door Edge Pull
• 3/4" width allows installation on narrow as well as standard doors.
• Spring automatically returns lever flush with plate.
• Made from solid brass.
• Conforms to design requirements of ANSI/BHMA A156.14 D2801.
Dimensions:
3-7/8" H x 3/4" W
K7
Protection Trim
Hinges & Pivots
8400 Series Protection Plates
A
• Door protection plates are available in .050” thick brass, stainless
steel or aluminum; and 1/8” thick high impact polyethylene in clear
or black.
• Bevel edge options; specify B4E for all four edges.
• Mounting screw pack furnished standard, 16 screws per pack.
Optional screw packs are available for TEK or TORK screw heads.
Refer to the following chart for ordering.
• Specify NMH for no mounting holes.
• Specify NMH-A for no mounting holes with adhesive.
• Specify CS for counter sunk mounting holes.
• Specify ERS prepped with extra row of screws.
Kickplate Gasket Tape Tape is recommended when using a
brass plate on a metal door to reduce tarnishing from electrolytic
oxidation. One tape pack will cover an the perimeters of a 8” x 34”
kickplate. Order 8401 Gasket Tape.
B13
Pulls & Plates
C
34"-41"
1
1
1
2
2
2
42"-48"
1
1
2
2
2
2
E
26"-33"
1
1
1
1
2
2
Stops
4"-8"
9"-16"
17"-24"
25"-32"
33"-40"
41"-48"
22"-25"
1
1
1
1
1
2
US4
US10
US10B
US15
US26
US26D
BHMA
606
612
613
619
625
626
BHMA
629
630
BHMA
628
Residential Grade Kickplates available Carded only, finishes PA28, PA3, PA619,
PA716, B3, B505, B619, B716
USA 1.877.613.8766
Canada 1.905.403.1800
G
Finishes plastic
Clear and Black
Finishes aluminum
US Number
US28
F
Finishes stainless steel
US Number
US32 US32D
Exterior Hardware
Finishes brass
US Number
US3
605
D
*UL mark appears in upper right corner.
Number of screw packs required by plate size (specify TEK Screws or TORK screws).
8400
Protection Plate
8402 (UL)* Protection Plate
B13
Mop Plates
• Protect the bottom of the pull side of door subject to cleaning
and mopping procedures.
• Size Ranges:4" to 6" high, 22" to 48" wide
Kick Plates
• Protect the bottom of the push side of doors subject to
scuffing from foot traffic.
• Recommended for all doors subject to normal use
(especially doors using a closer).
• Size Ranges: 8" to 24" high, 22" to 48" wide
Stretcher Plates
• Protect doors at specific areas where consistent contact is made by
stretchers, service carts or other equipment.
• Usually applied to push side of doors.
• Specify “B4E” Option for beveled edges.
Armor Plates
• Protect lower half of doors from abuse by hard carts,
trucks and rough usage.
• Usually applied to push side of single doors and both sides
of double acting doors.
G
F
Exterior Hardware
E
Stops
D
C
B14
Pulls & Plates
A
Hinges & Pivots
Protection Trim
B14
USA 1.877.613.8766
Canada 1.905.403.1800
5PB1
5 Knuckle, Plain Bearing
PLAIN BEARING • LOW FREQUENCY • STANDARD WEIGHT
For use on Standard Weight Doors with Low Frequency Usage, not intended for use
with door closing devices.
• Dimensions & tolerances conform to ANSI - A156.7
• Packed with wood and machine screws
• 5PB1 Steel description conforms to ANSI - A8133
• 5PB1 Brass conforms to ANSI - A2133
• 5PB1 Stainless Steel description conforms to ANSI - A5133
Size (Inches)
3.5 x 3.5
4.5 x 4
4.5 x 4.5
5BB1
5 Knuckle, Ball Bearing
Size (mm)
89 x 89
114 x 102
114 x 114
Gauge
0.123
0.134
0.134
2 BALL BEARING • MEDIUM FREQUENCY • STANDARD WEIGHT
For use on Standard Weight Doors with Medium Frequency Usage
5BB1 Steel with steel pin
5BB1 Brass with stainless steel pin
5BB1 Stainless steel with stainless steel pin (630 finish only)
NRP = Non-Removable Pin
• 5BB1 Steel description conforms to ANSI - A8112
• 5BB1 Brass conforms to ANSI - A2112
• 5BB1 Stainless description conforms to ANSI - A5112
Size (Inches)
4x4
4.5 x 4
4.5 x 4.5
4.5 x 5
5 x 4.5
5BB1RC
5 Knuckle, Ball Bearing, Round Corner
Size (mm)
102 x 102
114 x 102
114 x 114
114 x 127
127 x 114
Gauge
0.130
0.134
0.134
0.146
0.146
2 BALL BEARING • MEDIUM FREQUENCY • STANDARD WEIGHT
For use on Standard Weight Doors with Medium Frequency Usage
5BB1 Steel with steel pin
• 1/4" radius
• 5BB1 Steel description conforms to ANSI - A8112
Size (Inches)
3.5 x 3.5
4.5 x 4
Size (mm)
89 x 89
114 x 102
Gauge
0.123
0.134
H I N G E S
5PB1 Steel with steel pin
5PB1 Brass with stainless steel pin
5PB1 Stainless steel with stainless steel pin (630 finish)
A R C H I T E C T U R A L
Full Mortise Hinges - 5 Knuckle
1500 Commercial Grade Pocket Door Frame for 1” to 13/8” Thick Doors
(13/4” with 1575 Adaptor Kit) to 125 lbs. (200 lbs. with 1125 Hanger)
ORDERING DATA
3/16"
3/4" (19mm)
1500
(5mm)
DOOR HEIGHT + 4-1/2" (114mm)
For 2 x 4 Construction. Removable aluminum
track with convex rails for smooth quiet
operation, rust resistant steel reinforced wood
split studs, jump proof three wheel (1” dia.)
hangers, self adjusting floor anchors, 2’6” and
3’0” headers marked to cut to smaller door
sizes. Brass-tone steel parts. All frames for
doors up to 13/8” can be converted for 13/4”
doors with 1575PPK3 adaptor kit. All oversized
frames include 1575PPK3 adaptor kit.
1500 Series Pocket Door Frame Prices
Item No.
Max Door Size
lbs/Case
Frames for 80” Tall Doors up to 125 lbs.
152068PF
For Doors up to 24” wide x 80” tall x 13/8”
28/1
152468PF
29/1
152668PF
30/1
152868PF
30/1
153068PF
30/1
Frames for 80” Tall Doors up to 200 lbs. (Uses 1125 Ball Bearing Hanger)
152068HD
28/1
152468HD
29/1
152668HD
30/1
152868HD
30/1
153068HD
30/1
Frames Below include 1575 13/4” Adaptor Kit
1500
Item No.
153668PF
40/1
154068PF
42/1
*154668PF*
54/1
*155068PF*
55/1
Description
lbs/Case
Accessories
152070PF
32/1
152470PF
34/1
152670PF
35/1
1500PPK3
Replacement Hardware Kit
5/10
152870PF
37/1
1555PPK3
Converging Door Kit
3/10
153070PF
39/1
1-3/4” Door Adapter Kit
3/10
153670PF
43/1
154070PF
50/1
*154670PF*
57/1
*155070PF*
61/1
1575PPK3
Steel Wrapped Uprights
Please Note: 3’6” and 4’0” Frames have 1 extra pair of uprights. 4’6” and
5’0” Frames have 2 extra pairs of uprights.
1568UPRT
80” Upright Pair with 13/8” Floor Bracket
72/6
1570UPRT
75/6
1580UPRT
86/6
*1590UPRT*
96/6
Hangers
1120
Standard Hanger, max weight 125 lbs.
13/50
1125
Ball-Bearing Hanger, max weight 200 lbs.
23/50
1121
Hanger Plate w/ screws
9/100
152080PF
35/1
152480PF
39/1
152680PF
40/1
152880PF
41/1
153080PF
43/1
153680PF
44/1
154080PF
50/1
*154680PF*
59/1
*155080PF*
62/1
*152090PF*
38/1
*152490PF*
40/1
*152690PF*
41/1
*152890PF*
42/1
*153090PF*
44/1
*153690PF*
56/1
*154090PF*
62/1
*154690PF*
72/1
*155090PF*
80/1
11
Multiple-Door Sliding Door Hardware
200MD, 100MD, 111MD Shown below are typical 3 track layouts for 1-3/8” doors. Other door thicknesses may be used. For thicker doors, the tracks must be spaced further apart and a
wider header may be necessary. Also, more than 3 tracks may be used by extending the header and using other track combinations as required.
200MD Series-300 lbs. Doors
6’, 8’, and 9’ Sets Utilizing 200, 100, and 111 Hardware Sets.
200MD Series Hardware Sets- 300lbs Doors (min 1-1/8” thick)
6-1/2" (165mm) Header
200
200
Set Image
200
3-1/8" MIN.
(79mm MIN.)
3-7/8" MAX.
(98mm MAX.)
1-3/8" Door
(35mm)
1-3/8" Door
(35mm)
1-3/8" Door
(35mm)
Part #
Track
Length
Max Door
Width (ea)
Max Door
Weight (ea)
200M0723
70”
1829mm
24” x 3
610mm x 3
300 lbs.
136 kgs.
200M0963
94”
2438mm
32” x 3
813mm x 3
300 lbs.
136 kgs.
200M1083
106”
2692mm
36” x 3
914mm x 3
300 lbs.
136 kgs.
200M1443
142”
3657mm
48” x 3
1219mm x 3
300 lbs.
136 kgs.
Set consists of 3-200 tracks, 3-1050 bottom tracks, 6-2020
hangers, 6-1705 guides, and 2-2055 track stops.
100MD Series Hardware Sets- 200lbs Doors (min 1” thick)
5-1/4" (133mm) Header
100
100
Set Image
100
1-3/4" MIN
(45mm MIN
2-1/4" MAX
(57mm MAX
1-3/8" Door
(35mm)
1-3/8" Door
(35mm)
1-3/8" Door
(35mm)
111
1/2"
1/4"
1-3/8" Door
(35mm)
1-9/16" MIN
(40mm MIN
1-7/8" MAX
(48mm MAX
(12.5mm)
1-3/8" Door
(35mm)
1-3/8" Door
(35mm)
1705
1/4 ROUND
OR CARPET
1-3/8" Door
(35mm)
1-3/8" Door
(35mm)
1705
1705
HARD
WOOD
HARD
WOOD
100M0723
70”
1829mm
24” x 3
610mm x 3
200 lbs.
91 kg.
100M0963
94”
2438mm
32” x 3
813mm x 3
200 lbs.
91 kg
100M1083
106”
2692mm
36” x 3
914mm x 3
200 lbs.
91 kg
100M1443
142”
3657mm
36” x 3
1219mm x 3
200 lbs.
91 kg
3/4" X 1-1/8"
3/4" X 1-1/8"
(19mm X 29mm) (19mm X 29mm)
(200 SERIES 3/4" x 1-1/4" (19mm X 32mm))
Tracks can be cut down for smaller openings.
Part #
Track
Length
Max Door
Width (ea)
Max Door
Weight (ea)
111M0723
70”
1829mm
24” x 3
610mm x 3
150 lbs.
68 kgs.
111M0963
94”
2438mm
32” x 3
813mm x 3
150 lbs.
68 kgs.
111M1083
106”
2692mm
36” x 3
914mm x 3
150 lbs.
68 kgs.
111M1443
142”
3657mm
48” x 3
1219mm x 3
150 lbs.
68 kgs.
1-3/8" (35mm)
1-7/16" (37mm)
1/4 ROUND
OR CARPET
All nosing and hardware filler supplied by others. Surface mount shown/
Bottom channel may be recessed into floor. Spacing and dimensions will
vary with other door thicknesses.
24
Max Door
Weight (ea)
Set Image
1050 Bottom Track- Included w/ all Sets
1-3/8" Door
(35mm)
Max Door
Width (ea)
111MD Series Hardware Sets- 150lbs Doors (min 3/4” thick)
111
1/2"
(12.5mm)
(6.4mm)
Track
Length
5-1/4" (133mm) Header
111
Part #
2054 PLBG
MULTI PULL CATCH
2054PLBG
Multi Pull Catch
National Guard Products, Inc.
Toll Free Phone 1-800-647-7874
Toll Free Fax 1-800-255-7874
Self Adhesive Seals
HEAD &
LATCH SIDE
HEAD &
LATCH SIDE
1/4"
Silicone
JAMB
5050B Brown
5050C Charcoal
5050W White
5050T Tan
5050CL Clear
*
DOOR
(optional astragal
application)
JAMB
DOOR
1/2"
DOOR
JAMB
ESS
Silicone
3/8"
1/2"
10C
JAMB
1/4"
DOOR
6"
5/1
Self Adhesive Seals
PROTECTION, INSIDE OUT
HINGE SIDE
S
10C
*Edge Sealing System on 20 min
rated wood doors up to 4’0 x 8’0 single, 8’0 x 8’0 std. pair with 9800 or
9500 at meeting edge.
HINGE SIDE
2525B Brown
2525C Charcoal
2525W White
2525T Tan
5060B Brown
5060CL Clear
S
10C
S
Available in 17’, 20’, 21’, 25’ and 300’ rolls.
Available in 7’, 8’, 9’,
17’, and 21’ rolls
Available in 17’, 20’, 21’, 25’ and 300’ rolls.
Neoprene Gasketing
11/32"
7/16"
7/16"
7/16"
7/16"
5020B Brown
5020C Charcoal
Kerf Application
5021B Brown
5020W White
5021C Charcoal
361
362
363
width
18’, 21’, 50’ rolls 3/8”
18’, 50’ rolls
1/2”
18’, 50’ rolls
3/8”
LATCH SIDE
DOOR
HINGE SIDE
DOOR
5021W White
10C
S
Available in 36”, 48”, 84”, 96” and 108” lengths.
“FATT”
Fast Attach Two-Way Tape
Fast attach two way tape provides an easy and effective alternative to gasketing installation. A 1/2” wide 2-way tape is
applied to the metal housing insuring a quick and easy installation. Then for security, 3 tek-type self drilling screws are
used to further secure each piece of material to the frame
stop. A no problem installation with no holes to drill.
To order add suffix “FATT” to product number. See price list
for products available with this feature.
FATT IS NOT CLASSIFIED FOR USE ON FIRE DOORS.
50
E-mail: [email protected]
www.ngpinc.com
thickness
x 3/16”
x 1/4”
x 1/8”
Toll Free Fax 1-800-255-7874
601
601A
601B
601DKB
600
600A
600B
600DKB
8"
7/8"
O
OV633A
OV633B
OV633DKB
OV634A
OV634B
OV634DKB
5 1/2"
B606A
B606B
B606DKB
A605A
A605B
A605DKB
1"
1"
1/2"
1/2"
.45
7/16"
7/
1 7/16"
#6 x 3/4” Stainless Steel Sheet Metal
Screws furnished.
S
7/8"
S
10C
1/
2"
10C
All Products this page.
S
10C
10C
10C
A617A
7/
10C
603A
603DKB
602A
602DKB
8"
C627A
C627B
C627DKB
9/16"
Wild Hair® - Nylon Brush Seals
5 1/2"
1 3/8"
3/4"
1"
5 1/2"
5/8"
10C
1/2"
10C
5/8"
10C
7/16"
S
3/4"
5/8"
10C
10C
9/16"
10C
1 3/8"
3/4"
C607A
C607B
C607DKB
4"
2 1/2"
2 1/2"
1 3/4"
1 3/4"
1"
1 9/16"
10C
1 1/16"
4"
1 3/16"
10C
1 3/8"
10C
D608A
D608B
D608DKB
E609A
E609B
E609DKB
G610A
G610B
G610DKB
H612A
H612B
H612DKB
I-615A
I-615B
I-615DKB
G611A
G611DKB
H614A
H614DKB
I-616A
I-616DKB
56
Toll Free Fax 1-800-255-7874
Drip Strips
black rubber covered
fabric astragal
14RA
14RB
14RDKB
1 1/2"
1 3/4"
Available for 2 1/4”
112N
doorspecify
17
17DKB
5/8"
112N DkB
3/4"
1 1/2"
eoprene
Max.
1 1/2"
16A
16B
16DKB
23/32"
2 1/2"
1 3/16"
Specialty Astragals, Drip Strips, Overhead Door Bottom Seal
neoprene
1/4"
Overhead
Door Bottom
Seal
112N
112NDKB
5/32"
81369N
81369NDKB
Security Astragal
1 1/8"
96" MAXIMUM HEIGHT
2 3/4"
detail 1/2 size
145PA
145PB
145PDKB
Spring loaded protection for pairs of outswinging
doors up to 96” in height. Pile insert for weather
protection, sturdy aluminum for pry bar protection.
neoprene
1/8"
#8 x 1 1/4" Stainless Steel Screw
Glass Door Astragal Seals
Our glass door seal consists of translucent PVC channel and nylon brush for an attractive solution to a difficult problem.
15/16"
15/16"
5/8"
1/2"
5/8"
1/2"
15/16"
A650
nylon brush
5/8"
7/16"
7/16"
5/8"
Order as set to receive two pieces
A651
7/1
6"
Maximum length120”
66
www.ngpinc.com
nylon brush
Toll Free Fax 1-800-255-7874
10C
All products this page.
653 .78 lbs./ft.
653DKB .78 lbs./ft.
1/4"
1/2"
1/4"
Typical Wall .125
655 .84 lbs./ft.
655DKB .84 lbs./ft.
Typical Wall .125
3/4"
1/4"
5 1/2"
1/2"
Offset Thresholds
1/2"
5 1/2"
1/2"
1"
Typical Wall .125
656 1.00 lbs./ft.
656DKB 1.00 lbs./ft.
659 .89lbs./ft.
659DKB .89 lbs./ft.
Typical Wall .125
Carpet Dividers
414 .31 lbs./ft.
414DKB .31 lbs./ft.
416
1/2"
Carpet Edges
Typical Wall .141
3/8"
.19 lbs./ft.
1 7/16"
3/8"
1 3/4"
Typical Wall .188
2 1/2"
1/2"
403 .70 lbs/ft.
Typical Wall .125
403DKB .70 lbs./ft.
417 .50 lbs./ft.
417DKB .50 lbs./ft.
3/8"
4"
Typical Wall .125
4"
404 .70 lbs./ft.
404DKB .70 lbs./ft.
Typical Wall .125
3/4"
Typical Wall
.125
3/4"
Carpet Dividers/Carpet Edges
7"
1 3/4"
414-75 .39 lbs./ft.
414-75DKB .39 lbs./ft.
404-75 .80 lbs./ft.
404-75DKB .80 lbs./ft.
409 1.20 lbs./ft.
409DKB 1.20 lbs./ft.
Typical Wall .125
6"
16
www.ngpinc.com
1/2"
4"
1/4"
1/2"
6"
Toll Free Fax 1-800-255-7874
A - clear
B - gold
DKB - dark bronze
All products
this section:
OK for use on
‘S’ label doors.
neoprene is black
10C
1 3/4"
1 3/4"
23/32"
neoprene
15NA
15NB
15NDKB
26NA
26NDKB
23/32"
1/2"
1/4"
1"
3/4"
1 3/16"
neoprene
112N
112NDKB
Door Shoes - Neoprene
Neoprene Door Shoes
neoprene
1"
1/4"
118NA
118NDKB
113NA
113NDKB
neoprene
119N
119NA
119NB
119NDKB
23/32"
neoprene
1/2"
neoprene
23/32"
1/4"
1 3/16"
1"
3/4"
1 3/4"
Door Bottom Seals
1 3/4"
23/32"
1 1/4"
3/8"
116N
116NDKB
neoprene
5/16"
3/4"
rubber covered
fabric
3/16"
14RA
14RB
14RDKB
3/16"
neoprene
1/4"
136N
136NDKB
Mortise 7/16” wide x desired depth.
#4 SMS furnished.
Available for a 2 1/4” door - specify
#6 x 3/4” stainless steel sheet metal screws furnished.
1"
Pile Door Shoes
1 7/16"
154P
154PDKB
gray
pile
3/8"
5/32"
254P
254PDKB
www.ngpinc.com
gray
pile
3/8"
1 3/4"
67
FA-Series and F-Series
Residential Lock Sets
Knob/Lever Design Options — FA-Series
4-7/8"
123 mm
Andover
2-3/4"
70 mm
2-1/4"
57 mm
2-3/4"
70 mm
Danbury
2-5/16"
59 mm
2-3/4"
69 mm
2-9/16"
65 mm
4-1/
105
4-13/16"
123 mm
4-1/2"
114 mm
2-3/4"
69 mm
2-3/4"
69 mm
2-3/4"
69 mm
Callington
2-1/2"
64 mm
St. Annes
2-3/8"
60 mm
2-1/4"
57 mm
Champagne
2-7/16"
62 mm
2-5/8"
123 mm
Merano
French Door Escutcheon
See page 25 for Finish Samples
FINISHES
Shown with
Champagne
Lever
FRENCH DOOR ESCUTCHEON
As a decorative option, French door escutcheons can be
added to any F/FA-Series knob or lever function, except
for keyed levers (F51/FA51). The French door escutcheons
do come standard on the FA patio knob function (FA30).
ADA-COMPLIANT PRODUCTS
In compliance with the American National Standards Institute
(ANSI A117.1) and the Americans with Disabilities Act (ADA),
Schlage Lock Company offers a wide selection of locks
designed for the needs of the physically challenged. These
solid lever designs are available as inside trim on handlesets.
Knobs
Siena
Plymouth
Georgian
Orbit
Bell
Andover
Danbury
505 605 609 613 619 620 622 625 626 716
Levers
Avanti
Accent
Flair
Manhattan
Jazz
Elan
Callington
Champagne
Merano
St. Annes
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
2-3/8"
1"
60 mm
25 mm
DOOR PREPARATION
2-1/4"
57 mm
= Helps meet LEED certification
= Complies with ADA Accessibility Guidelines
26
1" dia.
25 mm
2-1/8"
54 mm
U.S.A. 1.800.847.1864 | Canada 1.905.403.1800 | www.schlage.com
CS 210/RS 210 Series
Interconnected
Lock
Introducing the Schlage Interconnected lock.
The new Schlage CS and RS 210 Interconnected Locks
combine exclusive options with increased strength,
for both residential and commercial applications.
The Schlage CS and RS 210 feature single motion
egress to meet Life and Safety code requirements, as
well as adjustability from the standard 4” to 5-1/2”
door preps. Robust performance exceeds BHMA
grade 2 requirements, giving the CS and RS 210 the
combination of aesthetics, versatility and strength.
Features and Benefits
Reliable: •Meets all ANSI/BHMA A156.25
Grade 2 requirements
•3 hr. UL fire rating
Field Configurable:
•Works with door prep of 4” or 5-1/2”
Adaptable:
•15 Levers styles
•2 Escutcheon styles
•6 Finishes
Flexible:
•FE210: Electronic Deadbolt
•RS210: B60 Trim
•CS210: B500 Trim
 SFIC and FSIC
Lever Styles
Jazz
Elan
Jupiter
Callington
Merano
Manhattan
Avila
Champagne
Escutcheon Styles
Avanti
Flair
Saturn
St. Annes
Accent
Specifications
4” to 5 1/2”
adjustable
door prep
Plymouth Escutcheon
Decorative Camelot Escutcheon
Deadbolt Choices
• 3 styles - (2) for mechanical security (1) for electronic
Mechanical
RS200
FE200
Cylinder Choices - available for CS 200 Series only
• 3 options - standard, full size or small format interchangeable core
Full Size
Interchangeable Core
•
•
•
•
•
•
•
•
•
•
•
•
•
ANSI/BHMA Grade 2 certified
UL Rating – UL 3hr. rating is standard
Latch – UL latch comes with 1” x 2-1/4” square and
round corner faceplate (square corner standard, round
corner included in package). 1” edge bore required.
Strikes – 1-1/8” x 2-3/4” square corner deadbolt strikes
and 2-1/4“ x 1-5/8” square corner full lip latch strike
reinforcer. Dust box not included.
Backset – Adjustable backset, fits 2-3/8” or 2-3/4” backsets
Levers – All lever trim is non-handed and field reversible
Stile width – Minimum 4-1/2“ for 2-3/8” backset,
minimum 5“ stile for 2-3/4”. To ensure proper fit, use the
dimensions below
Return to Door – Saturn (SAT) and Neptune (NEP) levers are
return to door code compliant
Cylinder –
FE & RS Series
Standard: 6 pin solid brass, keyed 5-pin
CS Series
Standard: 6 pin solid brass, keyed 5-pin, C123 keyway
Optional: FSIC (full size interchangeable core),
SFIC (small format interchangeable core)
Keys – (2) Silver nickel keys included
Door Range – 1-3/8” to 1-3/4” standard. 1-3/4“
to 2 optional. Must be specified
Center to Center – Fits 4” or 5-1/2” center to center
door preps.
*Credential – Deadbolt is operated using iButton
credential (sold separately)
*Note: Only available on the FE200.
Electronic
CS200
Latitude
Neptune
Small Format
Interchangeable Core
Finishes
605
Bright Brass
609
Antique Brass
619
625
Satin Nickel
Bright Chrome
877-671-7011 • schlage.com
626
Satin Chrome
716/643e
Aged Bronze
©2012 Ingersoll Rand
005085
01/12
Cylinders for Schlage Locksets
Cylinders for B250-Series
Cylinders for A-Series Knobs
Number
Description
21-002
6-Pin conventional cylinder (standard, non-Orbit)
21-002-122
6-Pin conventional cylinder (standard, Orbit design only)
20-724
Number
Description
22-001
5-Pin C, CE, E, F cylinders only
22-002
6-Pin conventional cylinder
20-729
20-729-XP
20-529
20-529-XP
Primus cylinder
Primus XP cylinder
Primus UL437 Listed high security cylinder
Primus XP UL437 Listed high security cylinder
Primus cylinder, non-Orbit
20-724-XP
Primus XP cylinder, non-Orbit
20-724-122
Primus cylinder, Orbit design only
20-724-122-XP
20-524
Primus XP cylinder, Orbit design only
Primus UL437 Listed high security cylinder, non-Orbit
20-524-XP
Primus XP UL437 Listed high security cylinder, non-Orbit
20-524-122
Primus UL437 Listed high security cylinder, Orbit design only
20-524-122-XP
Primus XP UL437 Listed high security cylinder, Orbit design only
21-003
Conventional hotel function (A85) with indicator, non-Orbit
21-003-168
Conventional hotel function (A85) with indicator, Orbit only
Available 606 and 626 Þnish only.
See B250-Series cylinders for locks ordered before 03/08.
Deadbolt Cylinders for S200-Series
Number
Description
21-081
6-Pin conventional cylinder
24-769
24-769-XP
24-569
20-569-XP
Primus cylinder
Primus XP cylinder
Cylinders for AL-Series Levers
Number
Description
21-020
6-Pin conventional cylinder (standard)
20-728
Primus cylinder
20-728-XP
20-528
20-528-XP
21-021
Primus XP cylinder
Conventional hotel function (AL85) with occupancy indicator
Cylinders for B500-Series - Single Cylinder Deadbolts
Number
Description
Door Thickness
22-003
Conventional
13/8Ó- 13/4"
22-004
Conventional
13/4Ó- 21/4 Ó
20-188
Primus
13/8Ó- 17/8 Ó
Primus XP
13/8Ó- 17/8 Ó
Primus
17/8Ó- 21/4 Ó
20-189-XP
Primus XP
17/8Ó- 21/4 Ó
20-190
Primus UL
13/8Ó- 17/8 Ó
Primus XP UL
13/8Ó- 17/8 Ó
Primus UL
17/8Ó- 21/4 Ó
Primus XP UL
17/8Ó- 21/4 Ó
20-188-XP
20-189
20-190-XP
20-191
20-191-XP
8
Full Size Interchangeable Core Cylinders for Schlage Locksets
Full Size Core Only
Number
Mechanism
23-030
Conventional core
30-120
Conventional core for hotel function (specify hand)
20-740-XP
Primus XP core (not available in hotel function)
Available 606 and 626 Þnish only. Order control keys separately.
Full Size IC Housings for Bored Deadlocks, Less Core
Lockset
Series
Description
Number
Specify Finish
Outside
B610-203, B610-205
605, 609, 612, 613, 619, 625,
626, and 716
Inside
B610-028**
605, 609, 612, 613, 619, 625,
626, and 716
B500-Series
B250, H, S200-Series
Outside
22-061
Inside of B252
22-062
605, 606, 609, 610, 611, 612,
613, 616, 625, 626
Outside
B610-027
605, 606, 609, 612, 613, 625,
626
Inside
B610-028
See Note Below
B600 / 700-Series
Specify Þnish of B610-031 inside snap-on faceplate ordered separately for BC162 and B662/762.
**Inside housing does not include snap-on faceplate
KS43F
KS72F
KS92M
Full Size Interchangeable Core Padlocks
Part #
Shackle Dimensions
A
B
C
LESS CYLINDER - FULL SIZE INTERCHANGEABLE CORE
BRASS BODY
KS43A3200
3 8
KS43D3200
3 8
KS43F3200
3 8
KS43G3200
/Ó
3 4
/Ó
3 4
/Ó
1 2
1 /Ó
3 4
/Ó
/Ó
2Ó
3 4
3 8
/Ó
4Ó
3 4
/Ó
1Ó
7 8
/Ó
2Ó
7 8
/Ó
1Ó
3 4
/Ó
/Ó
/Ó
STEEL BODY
KS72M3200
7 16
KS72F3200
7 16
KS92M3200
3 8
/Ó
/Ó
/Ó
Note: To order Primus XP add the sufÞx - XP to the
Primus part number. (Example: 12-345-XP)
15
Full Size Interchangeable Core Mortise Cylinders
1 1/2Ó
Cylinder Only
Compr. Ring & Spring
With Blocking Ring
Cylinders for Schlage L-Series Mortise Locks
Core Mechanism
Function
Conventional
Primus, Primus XP
Housing
Less Core
All Except Below
30-008
20-798, 20-798-XP
30-007
L9060P Outside
30-030
20-782, 20-782-XP
30-032 + 36-083
L9485P, L9486P
Hotel Funtions
30-010*
N/A
30-007
All Except Below
30-138
20-776, 20-776-XP
30-137
L9060P Outside
30-030 + 36-083 +
35-082-030
20-783, 20-783-XP
30-032 + 36-083 +
36-082-050
L9485P, L9486P
Hotel Funtions
30-040*
N/A
30-137
Design
L&N
Escutcheons
(cylinders with
compression ring)
Sectional Trim
(cylinder with
compression ring,
spring and
3/8Ó blocking ring).
9060 requires
1/2Ó blocking ring.
L583-489
Cam for All Functions
Except L9060 Outside
K510-680
Cam for
L9060 Outside
* Hotel function cores are handed. Specify hand of door.
Mortise Cylinders with Straight Cam for Exit Devices
Number
Core Mechanism
26-091
Collar
Compression ring & spring
Conventional core
20-061
3/8 Ò blocking rings +
compression ring & spring
20-763, 20-763-XP
Primus/Primus XP core
20-771, 20-771-XP
3/8 Ò blocking rings +
compression ring & spring
None
20-059
Housing less core
26-064
Notes 1.
2.
3.
4.
16
Available 605, 606, 609, 610, 612, 613, 625, and 626 Þnish. Cores furnished 606 and 626 only.
To differentiate between Classic and Everest, specify keyway. Example: C or CP (Classic), C123 (Everest). Everest C123 keyway standard.
All cylinders are 11/2ý long.
Specify LKB if 0-bitted Primus XP cylinders are required less key blanks.
K510-730
Straight Cam,
Other Applications
Full Size Interchangeable Core Cylinders for Exit Devices,
Aluminum Doors, etc.
Interchangeable Core Rim Cylinders for Exit Devices
Number
Core Mechanism
20-057
Conventional core
20-757
Primus core
20-757-XP
20-079
Primus XP core
Housing only, less core
Available 605, 606, 609, 610, 612, 613, 625 and 626 Þnish.
Cylinders for Adams Rite MS and 4700 Series
Lori 4500 Series and Corbin Russwin DL3000 Series
Number
Core Mechanism
Collar
26-098
Conventional core
20-062
Conventional core
3 16
20-766
Primus core
3 16
Primus XP core
3 16
Housing less core
None
20-766-XP
20-060
/ Ó + 3/8Ó blocking rings
K510-711
Adams Rite
MS Cam
These cylinders include set screw pack B220-050 for Adams Rite locks.
Cylinders for Adams Rite 4070 Series Deadlocks
Number
Core Mechanism
Collar
20-091
Conventional core
3 16
20-722
Primus core
3 16
Primus XP core
3 16
Housing less core
None
20-722-XP
20-090
Notes 1.
2.
3.
4.
B520-378
Adams Rite
4070 Cam
Mortise cylinders available 605, 606, 609, 610, 612, 613, 625, and 626 Þnish. Cores furnished 606 and 626 only.
To differentiate between Classic and Everest, specify keyway. Example: C or CP (Classic), C123 (Everest).
All cylinders are 11/2ý long.
Specify LKB if 0-bitted Primus XP cylinders are required less key blanks.
17
T
6210, 6211, 6211AL, 6211WF ELECTRIC STRIKES
6211
Electric strike for use with mortise
locks without deadbolt or cylindrical locks on single door, hollow metal frame applications.
Designed to replace Von Duprin
3140 or Folger Adam 712.
FEATURES
● All Stainless Steel Construction
● Accepts 3/49 (19mm) Throw
Latchbolt
● Six Finishes
● Non-handed
● Fail Secure
● Horizontally Adjustable
● Plug Connectors
VON DUPRIN
VON DUPRIN
VON DUPRIN
locks without deadbolt on single
door, hollow metal frame applications and using ANSI prep at
standard height, Strike pocket
inserts are provided to accommodate different manufacturers
deadlocking trigger locations.
6211WF
locks without deadbolt or cylindrical locks on single door, wood
frame applications. Designed to
replace Folger Adam 732.
VON DUPRIN
6210
6210
VON DUPRIN
6211
OPTIONS
●
Fail Safe
Dual Monitor Switches
● Entry Buzzer
●
VON DUPRIN
VON DUPRIN
6211AL
locks without deadbolt or cylindrical locks on single door, aluminum frame applications. Designed
to replace Folger Adam 722.
6211AL
12V
24V
Resistance in Ohms510% @ 707F
21
72
Watt-seated @ 707F
7.5
8
Amps-seated @ 707F
.6
.33
Amps-inrush @ 707F
.6
.33
DIMENSIONS AND CONFIGURATIONS
6210
6211
17/169
(37mm)
1 1/ 49
(32mm)
1 3/ 49
(44mm)
(124mm)
7/ 89
1 3/ 89
(35mm)
(86mm)
3 1/ 49
(83mm)
(22mm)
1/ 29
(13mm)
1/ 89
(3mm)
1 1/ 49
(32mm)
4 7/ 89
(124mm)
129 (305mm)
Minimum
Clearance
7/ 89
1 1/ 49
(32mm)
(22mm)
1/ 29
(13mm)
3 3/ 89
(86mm)
21/169
(52mm)
1/ 89
(3mm)
129
4 7/ 89
(305mm) (124mm)
Minimum
7/ 89
Clearance
(22mm)
1 1/ 49
(32mm)
3 3/ 89
(86mm)
21/169
(52mm)
1/ 29
1/ 89
(13mm) (3mm)
6211WF
6211WF
115/329
(49mm)
111/169
(43mm)
111/169
(43mm)
3 3/ 89
4 7/ 89
6211AL
115/329
(49mm)
1 1/ 49
(32mm)
UL listed Burglary
Resistant CVXY and
Electric Strike for fire
doors or frames GXAY
(fail secure only).
ANSI E59321
VON DUPRIN
SPECIFICATIONS
115/329
(49mm)
1 1/ 49
(32mm)
129
4 7/ 89
(305mm) (124mm)
Minimum
Clearance
4 1/ 29
(114mm)
3 3/ 89
(86mm)
21/169
(52mm)
7/ 89
(22mm)
1/ 89
(3mm)
39/169
(90mm)
Minimum
Clearance
7
98/99™ Rim Exit Device
299 Strike
98 and 99 rim exit devices for all types of single and double doors with mullion, UL listed for Panic Exit
Hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 98 device has a smooth mechanism case and the
99 device has a grooved case. The rim device is non-handed except when the following device options are
used: SD (Special Dogging), -2 (Double Cylinder) or SS (Signal Switch). See Opposite page for available
outside trim and device functions. Covers stock hollow metal doors with 86 or 161 cutouts on single doors
(may cover cutouts on pairs – consult template).
The 98/99 devices are available in the following finishes: US3, US4, US10, US26, US26D, US28, 313AN,
315AN and US32D for the 98 device only. See page 52 for component finishes and the inside cover for
finish chips.
Specifications
Device Functions
Device Lengths
Strikes
Device ships EO/DT/NL. Field selectable. For TP,K,or L remove NL
drive screw from device
3’
4’
2’4" to 3’ (711mm to 914 mm) Door Size
2’10" to 4’ (864 mm to 1219 mm) Door Size
299 – Dull Black
Optional Strikes – see page 39
Dogging Feature
Hex key dogging standard
Dogging Options
CD
SD
LD
Cylinder Dogging
Special Center Case Dogging
Less Dogging
see page 48
see page 48
see page 48
Electric Options
LX
RX
RX2
E
EL
SS
CX
ALK
Latchbolt Monitor Switch
Pushpad Monitor Switch
Double Pushpad Monitor Switch
Electric Locking & Unlocking
Electric Latch Retraction
Signal Switch
Chexit Delayed Exit
Alarm Exit Kit
see
see
see
see
see
see
see
see
Miscellaneous Options
Fasteners &
Sex Bolts (SNB)
Latch Bolt
Device Centerline from
Finished Floor
Center Case Dimensions
Mechanism Case Dimensions
Projection
PN Pneumatic Latch Retraction
-2 Double Cylinder
GBK Glass Bead Kit
42
42
42
44
43
43
45
42
see page 48
see page 48
see page 49
Includes 1 ³₄" (19mm) – 2 ¹₄" (57mm) Wood & Metal Doors
Optional SNB available for device, see next page for quantities
Deadlocking, ³₄" (19mm) throw
39 ¹³₁₆" (1011 mm)
39 ¹¹₁₆" (1008 mm) with Mullion
8" x 2 ³₄" x 2 ³₈" (203mm x 70mm x 60mm)
2 ¹₄" x 2 ¹₄" (57mm x 57mm)
Pushbar Neutral – 3 ¹³₁₆" (97 mm)
Pushbar Depressed – 3 ¹₁₆" (78 mm)
See page 53 for How to Order specification
4
page
page
page
page
page
page
page
page
© 2004 Ingersoll-Rand. May be copied for use with specification submittal.
98/99™ Rim Exit Device Standard Trim
Exit only
Dummy Trim
Pull when Dogged
98EO
99EO
98DT
99DT
98NL
99NL
98NL-OP
99NL-OP
Trim Description
––
990DT
990NL-R/V
110NL-MD
110NL-WD
Escutcheon Plate Size
––
3" x 14³₁₆" x ³₃₂"
(76x360x2mm)
3" x 14³₁₆" x ³₃₂"
(76x360x2mm)
––
Pull Center to Center
––
5¹₂" (140mm)
5¹₂" (140mm)
––
Projection
––
2" (51mm)
2" (51mm)
––
ANSI Function
01
02
03
03
Cylinder Type
––
––
Rim
Rim
Optional Trim
(See pages 32 – 34)
x990EO
x992EO
x994EO
x996EO
x991K-DT
x992L-DT
x994L-DT
x996L-DT
x696DT
x697DT
x991K-NL
x992L-NL
x994L-NL
x996L-NL
x696NL
x697NL
Optional #425 Sex Bolt
Quantity for Device
6
2
2
Lever
Key Locks & Unlocks
Lever – Night Latch
Key Retracts Latchbolt
98L
99L
98L-NL
99L-NL
98L-BE
99L-BE
98L-DT
99L-DT
996L-R/V
996L-NL-R/V
996L-BE-R/V
996L-DT-R/V
Escutcheon Plate Size
2³₄" x 10³₄" x ²⁷₃₂"
(70x273x21mm)
2³₄" x 10³₄" x ²⁷₃₂"
(70x273x21mm)
2³₄" x 10³₄" x ²⁷₃₂"
(70x273x21mm)
2³₄" x 10³₄" x ²⁷₃₂"
(70x273x21mm)
Pull Center to Center
––
––
––
––
2⁷₈" (73mm)
2⁷₈" (73mm)
2⁷₈" (73mm)
2⁷₈" (73mm)
ANSI Function
08
09
––
02
Cylinder Type
Rim
Rim
––
––
Optional Trim
(See pages 32 – 34)
x992L
x994L
x992L-NL
x994L-NL
x992L-BE
x994L-BE
x992L-DT
x994L-DT
Optional #425 Sex Bolt
Quantity for Device
2
2
2
2
Product Description
Product Description
Trim Description
Projection
For optional trims and functions see pages 32-34
Night Latch
Lever – Blank Escutcheon
Always operable
(No Cylinder)
Night Latch
Optional Pull Required
6
Lever Dummy Trim
Pull when Dogged
5
Alarmed Exit Devices
®
Chexit Controlled Exit Device
CX33A/CX35A
CX98/CX99
Rim device shown — Refer to Chexit Catalog for complete selection information.
CX Chexit is designed for use on delayed
exit applications. The Chexit system is
ideal for controlled areas. This concept in
delayed exit systems combines life safety
with the needs of security and meets all
requirements of NFPA 101 for “Special
Locking Arrangement.”
The Chexit system will keep an exit door
secured for a 15 second period, yet tied
into the fire alarm system will release
immediately when an alarm condition
exists. All controls, auxiliary locking,
local alarm, and remote signaling output
are self-contained in the Chexit assembly,
providing safe, secure and easy to install
door control hardware.
The Chexit system is ideal for highly
controlled areas such as airports,
hospitals, government facilities and
development labs, retail stores, libraries
and security facilities.
CX98 and CX99 are available for rim,
mortise lock and surface and concealed
vertical rod mounting styles. CX33A and
CX35A are available on rim mounting
style only.
For CX98/9927 and CX98/9957 Panic
and Fire Devices, two Rod Guards (RGO)
are required. For door heights over 7´
additional Rod Guards (RGO) will be
added as needed to protect the rods.
UL listed for use on panic or fire exit
doors 3´ or 4´ wide.
The Chexit device includes decal for
application on door, “PUSH UNTIL
ALARM SOUNDS. DOOR CAN BE
OPENED IN 15 SECONDS”.
A complete Chexit system requires a
PS873 power supply and a power
transfer. See pages 28 and 29.
FEATURES
• Non handed
• Field sizable
• 3⁄4˝ (19mm) throw, latch bolt
• Deadlocking
20
Request to Exit Switch is built in to
detect when someone attempts to exit.
Applying less than 15 pounds to the
push pad will cause this switch to start
an irreversible alarm cycle.
External Inhibit Input — This optional
input is provided to allow remote
override of the Chexit in the armed
condition. It also allows remote reset of
the Chexit in an alarmed condition.
Nuisance Alarm — When the Nuisance
Audible and Nuisance Delay options are
set to off the device will go into alarm as
soon as the push pad is touched. Turning
the Nuisance Delay on will require the
push pad to be pressed for 2 seconds
before the Chexit goes into alarm, which
is ideal in public areas. If the Nuisance
Audible and Nuisance Delay are both on,
the alarm will sound as soon as the push
pad is pressed, but the alarm sequence
will stop unless held for 2 seconds or more.
Fire Alarm Input — This input disables
the Chexit immediately upon a fire alarm.
Remote Alarm — A set of relay
contacts (rated 1 ampere, 24VDC)
are provided to give external alarm
indication. These contacts close when
the device is in an irreversible alarm
condition. These contacts can be used
to drive a horn, lamp, or other
signaling devices.
Key Switch — The Key Switch provides
the means to arm, disarm, or reset the
Chexit. The key can be removed in either
the Arm or Disarm position.
Indicator Lamp — The Indicator Lamp
determines the status of the Chexit.
When the lamp is off, it indicates
disarmed and is functioning as a normal
exit device. A slow flashing lamp
indicates armed. A fast flashing indicator
lamp indicates the device is in alarm.
Internal Horn –– Whenever the device is
in alarm or the push pad is pressed the
Internal Horn will sound. The volume
level of this horn exceeds 85 db at 6 feet.
Door Position Input –– An external door
position switch can be connected to the
Chexit. The door position switch will
cause the alarm to sound if the door is
not closed when the device is armed.
Internal Auxiliary Lock —The Auxiliary
Lock is engaged when the Chexit is
armed. The locking mechanism is
specifically designed to hold securely
even when the exit device is struck with
forceful blows.
User Definable Rearm Time –– The
Rearm Time is the amount of time after
the device is activated (via key switch or
external inhibit) before it arms. It is
designed to give someone time to pass
through the door before rearming
occurs. The user can change timing for
any time between 2 and 28 seconds in
two-second intervals.
There is also an infinite rearm setting
that requires the use of an external door
position switch. In this setting the door
remains in the rearm mode until the door
is closed. This can be useful on jet way
doors in an airport.
Factory Definable Delay –– Most
jurisdictions allow 15 seconds of delay
before allowing egress. In those cases
when 15 seconds is not appropriate,
Von Duprin can set the Chexit for any
delay time between 0 and 60 seconds
in two-second increments. For delays
greater than 15 seconds a letter from
the local authority must be provided
with the order.
Alarmed Exit Devices (cont.)
To Order, Specify:
1. Prefix product description number “CX”.
Example: CX99L
2. Door size other than 3´ (914mm).
Cylinders –– Cylinders are not furnished with the Chexit device
and must be specified when ordering. Uses a standard 1 1⁄4˝
(32mm) mortise cylinder for the device and the CD cylinder
dogging option.
3. Door thickness other than 1 3/4˝ (45mm).
4. Finish.
5. Handing, LHR or RHR. Required with “CD” option.
OPTIONS
(See Chexit catalog for all options and accessories)
RCM Remote Chexit Module –– is designed to provide the
concept of the Chexit delayed exit system for door sizes smaller
than the standard Chexit device can accommodate. The Chexit
module is installed in a control box and mounted in a remote
location. Features and functions of the standard Chexit exit
device are available on the Remote Chexit Module.
RCM Module
RCM Control
Box, Lens, Cover
Minimum Door Opening for CX and CX-R (RCM)
3´ (914mm)
4´ (1219mm)
Device
Length
Length
CX33A/35A RIM
2´10˝ (864mm)
3´4˝ (1016mm)
CX 98/99 RIM
2´10˝ (864mm)
3´4˝ (1016mm)
CX 98/9927
2´9˝ (838mm)
3´3˝ (1041mm)
CX 98/9947
2´9˝ (838mm)
3´3˝ (1041mm)
CX 98/9947-F
2´10˝ (864mm)
3´4˝ (1016mm)
CX 98/9975
2´10˝ (864mm)
3´4˝ (1016mm)
CX-R 33A/35A RIM 2´5˝ (864mm)
2´11˝ (1016mm)
CX-R 98/99 RIM
2´5˝ (864mm)
2´11˝ (1016mm)
CX-R 98/9927
2´4˝ (838mm)
2´10˝ (1041mm)
CX-R 98/9947
2´4˝ (838mm)
2´10˝ (1041mm)
CX-R 98/9947-F
2´5˝ (864mm)
2´11˝ (1016mm)
CX-R 98/9947WDC 2´5˝ (864mm)
2´11˝ (1016mm)
CX-R 98/9975
2´5˝ (864mm)
2´11˝ (1016mm)
SPECIFICATIONS
Continuous Duty –– 24VDC
Current In-rush –– 16 amperes
Current Holding –– .3 amperes
External Alarm Contact –– 1 ampere @ 24VDC
Fire Alarm Input, External Inhibit Input, Door Position Input –
set-up for normally closed dry contacts.
Basic Chexit single door application configuration consists of
the Chexit device, power transfer and PS873 power supply.
Using this setup, the Chexit will delay egress when armed and
act as a normal exit device when turned off.
120 VAC 3 x 14 ga.
Junction
Box
To Fire Alarm
2 x 18 ga.
2 x 12 ga.
2 x 12 ga.
2 x 18 ga.
PS873
Power Supply
EPT-10
Cable
Cylinder Dogging –– Special Center Case Cylinder dogging
option is available to allow push/pull operation of the Chexit,
when disarmed and used in a heavy traffic area. Prefix device
with “CD” and specify handing.
Gnd
+24
Fire Alarm
PS873
Power Supply
+24
Red
Gnd
Black
SC
White
FA
Yellow
DPS Orange
EI
Green
CM+ Grey
CM-
Violet
NO
Blue
C
Chexit
Cable
Brown
21
Accessories
Electrical Power Transfer
Electric Power Transfer provides
a means of transferring electrical power
from a door frame to the edge of a
swinging door. The units are completely
concealed when the door is in the
closed position, and are ideally suited
for installations involving abuse or
heavy traffic.
Two models are available; EPT-2, two 18
gauge wires and EPT-10, ten 24 gauge
wires.
The EPT-2 and EPT-10 are UL listed as
“miscellaneous door accessory.”
Pneumatic Controls
PNT-1 is available for pneumatic latch
retraction exit devices. Appearance and
dimensions are identical to EPT models.
SPECIFICATIONS
Housing — 9˝ x 11⁄ 4˝ x 15⁄ 8˝
(229mm x 32mm x 38mm)
EPT-2 — Two 18 gauge wires
Up to 2 amps @ 24VDC, with a
16 amps maximum surge
EPT-10 — Ten 24 gauge wires, up to
1 amp @ 24VDC, with a
16 amps maximum surge
5
PNT-1
⁄ 32˝ Tubing
TO ORDER, SPECIFY:
1. EPT-2, EPT-10 or PNT-1
2. Finish, SP28 or SP313
UL Listed as “Miscellaneous” Fire Door
Accessory” GVUX
UL listed for use on fire doors.
Door Applications
Up to 5˝ butt hinges - 180° Swing
5 1/2˝ butt hinges - 130° Swing
6˝ butt hinges - 110° Swing
3/4˝ butt offset pivots - 180° Swing
Not for use with swing clear hinges or
center-hung pivots.
Junction Box
High quality NEMA 1, junction boxes
provide convenient installation, available
in three models. These surface mounted
units are 10˝ (254mm) high, 10"
(254mm) wide and 6˝ (152mm) deep
and includes hinged door with twist
turn lock. 24 position terminal strip
will accept from 24 to 12 gauge wire.
Five models:
JB7
Junction box only.
JB7-R1 Junction box with SPDT Relay.
JB7-R2 Junction box with DPDT Relay.
JB7-R3 Junction box with DPDT Relay
on Make Relay.
JB7-R4 Junction box with DPDT Relay
on Brake Relay.
29
PS914
4 amp power supply
(Von Duprin)
Photo as shown includes optional board(s). Please
contact your local sales office or visit the support section
on our website for configuration assistance.
Overview
Features and benefits
Von Duprin’s power supply and option boards were designed to meet the specific
requirements of electrified fire exit devices.
§§
4A @ 12/24 VDC output, field selectable
with jumper
§§
Designed with high in rush current for
powering electrified panic devices
§§
Universal 120 - 240 VAC input
§§
Low voltage DC, regulated and filtered
§§
Electronic power limiting foldback circuit for
AC current overload protection
§§
Two polarized connectors for distribution
boards
§§
Fused primary input
§§
AC status monitor - isolated SPDT contacts
§§
AC input and DC output LED status indicators
§§
Cover mounted AC input indication
§§
Hinged cover with lock down screws
§§
High voltage protective cover
Installation is simplified by utilizing a flat mounting design and polarized locking
connectors for option boards. This new design eliminates the need for racks and side
connectors. The flat mounting of the option boards also provides for easier access to
the terminal blocks for connection of electrified devices (such as electrified panic
devices, strikes, card readers, etc.).
Common to the line of PS900 Series power supplies is a constant output rating at both
12v and 24v settings, universal 120 VAC to 240 VAC input, and polarized option board
connectors. New fire alarm interface board mounting allows outputs to be configured as
switched (power cut) or unswitched (power continues) when signal is provided.
* All PS900 Series power supplies and option boards have been tested and certified to meet UL 294.
Options
PS914 power supply specifications
§§ Emergency Interface/Fire Alarm Relay (FA)
Specification
Description
-- Must be installed on distribution boards
Input voltage
120/240 VAC, 50/60 Hz, universal input
Output voltage
4A @ 12 or 24 VDC
Field selectable with jumper
Switching supply, 5% regulation, 360mVpp max ripple
Enclosure
Grey/baked enamel
14" x 12" x 4" (H x W x D)
Eight 1⁄2" x 3⁄4" knockouts
Hinged cover with lock down screws
Operating temperature
32° - 120°F (0° - 49°C)
Certifications
UL 294
RoHS
FCC Part 15
Class 2
Option board compatibility
900-BB: Battery backup board only
900-BAT: Backup battery pack
900-BBK: Battery backup kit (backup board and battery pack)
900-FA: Fire alarm (must be installed on distribution boards)
900-2RS*: 2 Relay EL panic device control board
900-4R*: 4 Relay output board
900-4RL*: 4 Relay logic board
900-8F*: Fused 8 zone distribution board
900-8P*: PTC 8 zone distribution board
AC primary fuse size
6.3A, 250v, 5 x 20mm SLOW-BLOW
Battery fuse size
7.5A 32v ATO blade style
DC output protection
Overload protection - current limited foldback circuit
Indicators
LED indicators:
- AC input (visible on outside of enclosure)
- DC output
Isolated SPDT contacts to monitor AC power status
Weight (power supply)
Approx. 9.0 lbs
Weight (each battery)
4.0 lbs
AC input termination
3 position terminal block with protective cover
Wire capacity: 10 AWG max.
DC output termination
2 position terminal block
Wire capacity: 12 AWG max.
Distribution board connectors
2
Fire alarm board connector
No
Keylock
Optional
§§ Key lock available for added security (KL)
§§ Battery backup
§§ 2 relay EL panic device control board
§§ 2 relay QEL panic device control board
§§ 4 relay distribution board
§§ 4 relay distribution board with logic
-- Field configurable for:
§§ Time delay function
§§ Auto operator
§§ Security interlock
§§ 8 fused output distribution board
§§ 8 PTC output distribution board
* Optional distribution boards available with or without FA (Fire Alarm Relay)
Allegion, the Allegion logo, Von Duprin, and the Von Duprin logo are trademarks of Allegion plc, its subsidiaries and/or affiliates in the
United States and other countries. All other trademarks are the property of their respective owners.
About Allegion
Allegion (NYSE: ALLE) creates peace of mind by pioneering safety and security. As a
$2 billion provider of security solutions for homes and businesses, Allegion employs
more than 8,000 people and sells products in more than 120 countries across the
world. Allegion comprises 27 global brands, including strategic brands CISA®, Interflex®,
LCN®, Schlage® and Von Duprin®. For more, visit www.allegion.com.
© 2014 Allegion
004101 Rev. 08/14
www.allegion.com/us

sc 8 0 series - Pavilion Construction

Transcription

Similar documents

Zak McKracken – Mayan Maze Map

The Blanc - Westeck Windows and Doors

Product datasheet Hinged door Panic Bar

LifeScapes Highboy Storage Shed

LiftMaster 81LM

Rilo Kiley After Hours

- Stewart Brannen Millworks

Heavy Duty Concealed Magnetic Catch suitable for full size doors

“Over 125 Years of Quality” Double Acting Spring Hinges

Rigids brochure - Fitzgeralds Vehicle Body Builders