JCM Global® iVIZION® Banknote Validator Training Overview

Transcription

iVIZION™ Banknote Acceptor
JCM Training Overview
July, 2014
July, 2014
JCM TRAINING
OVERVIEW
Phone (800) 683-7248
(702) 651-0000
Fax (702) 651-0214
"JCM American Corporation has been accredited as an Authorized Provider by the
International Association for Continuing Education and Training (IACET)”
E-mail [email protected]
Web Address http://www.jcmglobal.com
JCM is a registered trademark of JCM American Corporation. All other product names
mentioned herein may be registered trademarks or trademarks of their respective companies.
Furthermore, ™, ® and © are not always mentioned in each case throughout this publication.
925 Pilot Road, Las Vegas, Nevada 89119
Office & Technical Support: (800) 683-7248 (option 1 after hours), FAX: (702) 651-0214
E-mail: [email protected]
http://www.jcmglobal.com
Part No. 960-100927R_Rev. 3
24
© 2014, JCM American, Corporation
Part No. 960-100927R_Rev. 3
1
July, 2014
PERSONAL NOTES AND COMMENT AREA
Table of Contents
Page
Write any pertinent notes or comments regarding your particular installation
here.
Overview ................................................................................ 3
iVIZION Unit ............................................................................................ 3
Component Locations ............................................................ 4
Components ............................................................................................ 4
Setting Communication Standards ......................................... 5
Selecting Communications Types ........................................................... 5
Connector Pin Designations ................................................... 6
JCM USB Tool Suite Overview ............................................... 7
JCM Tool Suite Functions - iVIZION ........................................................ 7
Banknote Acceptance Tests ................................................... 8
Entering Performance Mode .................................................................... 8
Performance Testing Mode ...................................................................... 9
Performance Testing Procedures ......................................... 10
JCM Tool Suite Standard Edition ........................................................... 10
Available Tests ........................................................................................11
Cleaning and Preventive Maintenance ................................. 12
Preventive Maintenance ........................................................................ 12
Sensor Identification .............................................................................. 13
Software Updating ................................................................ 14
JCM Tool Suite Application .................................................................... 14
Calibration ............................................................................ 15
When to Calibrate .................................................................................. 15
Calibrating the iVIZION .......................................................................... 15
iVIZION Utility Tool ............................................................... 16
CIS Image .............................................................................................. 16
ICB Setting ............................................................................................ 16
Error Tables .......................................................................... 17
LED Operational Condition Indicators ................................................... 17
LED Bill Jam Errors ............................................................................... 18
LED Reject Errors .................................................................................. 19
ICB Code Errors .................................................................................... 20
Operational Error Codes ........................................................................ 21
Lecture Notes
iVIZION-100 Parts List .......................................................... 22
Personal Notes and Comment Area ..................................... 23
Part No. 960-100927R_Rev. 3
2
23
July, 2014
iVIZION-100 Parts List
OVERVIEW
Part Number • 701-000148R
• 701-100112R
• 302-000001R
• 40i-000001R
This training course addresses the following JCM iVIZION® device versions:
• 201544
• 211266
Description
Power Supply PS75-002
iVIZION/TBV UAC Kit (alternate power supply option)
USB Male 'A' to USB Mini-B Cable
WBA/UBA to iVIZION Harness Cable Adapter for PS75-002 
or UBA/iPRO UAC Kit.
Reference Paper White KS-072 (without Guides)
Reference Paper White KS-089 (with Guides)
Table 1 iVIZION Versions
Device
iVIZION 100 SS
.
Thank you for choosing JCM products.
64 Mbits standard (expandable to 192 Mbits)
iVIZION LD
64 Mbits No Stacker
iVIZION SH
64 Mbits High Capacity Cash Box
iVIZION 100 SU*
*
Capacity/Contents
64 Mbits standard Up-Stack (expandable to 192 Mbits)
The Up-Stack (SU) Configuration is selected by a jumper at the rear of the iVIZION Frame (pins 24 to 15).
Refer to the iVIZION Operation and Maintenance Manual for more information.
IVIZION
UNIT
Figure 1 iVIZION Unit
Lecture Notes
Part No. 960-100927R_Rev. 3
22
Lecture Notes
3
COMPONENT LOCATIONS
OPERATIONAL ERROR CODES
Operational Errors are associated with a malfunction within the iVIZION®
Unit itself. Operational Errors are indicated by a RED LED flashing. By counting the flashes in-between the pause states, the error can be determined and
located in Table 9.
COMPONENTS
Table 9 Operational Malfunction LED Flash Error Codes
TRANSPORT UNIT UNDER SIDE
H
TRANSPORT UNIT
LOWER FRONT SIDE
J
O
LED
Color
I
B
D
E
A
L
S
Red
C
R
G
CASH BOX
BACKSIDE
Flash No.
Error Types
1
Stacker Full
CPU Comm Error
(Processors)
Sensor Adjustment Error
Speed Error
EEPROM Error
Transport Error
Reject Error
Stacker Pusher
Movement Error
Pusher Position Error
No Cash Box
No Acceptor Head
Anti-String Error
Reserved
Damaged Processor
(CPU) Board
Memory Error
3
4
5
6
7
N
K
Status LED
2
F
M
Q
8
9
10
11
12
13
14
(SHOWN ON END)
15
T
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
July, 2014
P
TRANSPORT UNIT,
FRAME & CASH BOX
Acceptor Unit
Acceptor Front Upper Guide Access Lever
Sentry-2 Bezel (Option)
Interface Connector
Transport Rear Upper Guide Access Lever
Transport Unit
Frame Housing
DIP Switch Block (Denomination Inhibit)
DIP Switch Block (JCM Custom Private Line)
Acceptor Unit Release Push Button
Status LED (Four (4) Colors: Red/Yellow/Green & Blue)
L.
M.
N.
O.
Front Panel Optional Bezel Connector
Transport Unit Release Lever
Power ON LED (Green)
USB (Mini-B) Software Download/Calibration & 
Maintenance Connector
P. Cash Box
Q. Stack Volume Indicator
R. Cash Box Window (confirms the last stacked Banknote 
Causes and Solutions
Detected a Cash Box Full condition
Communications Error between Processor (CPU) Boards
Abnormal Sensor Adjustment condition encountered
Transport Motor Speed is incorrect
No Initial Sensor Adjustment
Transport or Stacker jam condition
Jam condition during a Banknote Reject operation
Jam in the Stacker Assembly
Pusher Plate Sensor Error
Cash Box not detected
Acceptor Head Cover is not closed
Sensors detected irregular movement
N/A
Processor (CPU) component failure
ROM/RAM Failure – CPU Board
NOTE: Refer to the iVIZION Operation and Maintenance Manual for a full description of
errors and corrective actions.
Lecture Notes
Denomination Value)
S. Lock Installation Holes Locks are user provided)
T. Pusher Lever - manually moves the Pusher Plate down 
(Activate to confirm Denomination Value in Cash Box Windows “R”).
Figure 2 iVIZION Component Locations
Lecture Notes
Part No. 960-100927R_Rev. 3
4
21
ICB CODE ERRORS
ICB Errors indicate a Set-up or Configuration issue exists with an Intelligent
Cash Box (ICB). ICB errors are indicated by a flashing Blue LED. By counting the flashes in-between the pause states, the error can be determined and
located in Table 8.
Table 8 LED ICB Flash Error Codes
LED
Color
Blue
Status LED
Flash No.
Error Types
1
Reserved
2
3
4
ICB Function Error
ICB Read/Write Error
ICB Data Error
5
ICB Number Error
6
7
8
9
10
11
12
13
14
15
ICB Initialization Error
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
N/A
RFID Module in Cash Box not detected (Verify presence)
ICB Communications Failure
Data is incorrect / Hardware Failure
Mismatch of Asset Number between Cash Box and
iVIZION Unit
Replace Cash Box with a cleared Box
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Lecture Notes
July, 2014
SETTING COMMUNICATION STANDARDS
The following communication standards can be used with an iVIZION® Unit:
•
•
•
•
USB Interface – USB 2.0 Standard
Serial Interface – Photo-coupler Isolation
Serial Interface – RS232 Communications
Serial Interface – cc-Talk Communications.
SELECTING COMMUNICATIONS TYPES
RS232 or Photo-coupler Serial Communications Selection
The communication DIP Switch Blocks required for making these selections
are located on the Transport Unit under the Validator Head. 
To change these communications settings proceed as follows:
1. Remove the Validator Head from the Transport.
2. Remove the DIP Switch Block Cover from the Transport Unit.
3. Change the DIP Switches as required for selecting the related communication
standard desired (See Table 2).
NOTE: When changing the type of iVIZION Serial Communications,
Switches JP2 and JP3 located on the Control CPU Board must be set to
identical switch positions.
Table 2 Serial Communications DIP Switch Settings
Control CPU Board JP2 & JP3
Mark
JP2
JP3
R↔P
R↔P
Switch No.
Non-Marked (R)
JP2
RS232C
JP3
RS232C
Marked (P)
Photo-Coupler
Isolation (Standard)
Photo-Coupler
Isolation (Standard)
NOTE: USB Interface and cc-Talk Standards are set by selecting and
modifying the proper pins on the iVIZION’s External 26-Pin
Communications Connector identified in Section 2 of the iVIZION®
Operation and Maintenance Manual.
Lecture Notes
Part No. 960-100927R_Rev. 3
20
5
CONNECTOR PIN DESIGNATIONS
Refer to the iVIZION® Operation and Maintenance Manual to identify the pin
designations assigned for the various communication Protocols supported via
the iVIZION® Unit’s 26-Pin External Signal Communications Connector.
July, 2014
LED REJECT ERRORS
Reject Errors indicate why a Banknote was not accepted. Reject Errors
are represented by a flashing Green LED. By counting the flashes inbetween the pause states, the error can be determined and located in Table 7.
Table 7 LED Reject Error Codes
Status LED
LED
Color Flash No.
Error Types
1
2
3
Green
4
5
6
7
8
9
10
11
12
13
14
15
Banknote Insertion Error
UV Sensor Error
Banknote Detected in
Acceptor
Adjustment Error
Transport Timing Error
Denomination Error
Photo Pattern Error 1
Photo Level Error
INHIBIT Error
Reject Command
Ticket Error
Transport/Stacker Error
Banknote Length Error
Photo Pattern Error 2
Banknote Identity Error
Skewed Insertion
Check/Clean the UV Sensors
Check/Clean Banknote Path
Check/Clean the CIS/Transmissive Sensors
Check Motor Speed
Banknote not validated, Check/Clean all Sensors
Banknote Pattern not recognized, Clean Path
Check/Clean the Banknote Path
Banknote rejected due to DIP Switch setting condition
Host commanded Banknote reject
Ticket inserted Upside Down
Sensors blocked in Stacker
Banknote length longer than specified, Check Banknote Type
Banknote pattern not recognized, Clean Path
Unidentified Banknote, Check Sensors, Clean Path
Lecture Notes
Part No. 960-100927R_Rev. 3
6
Lecture Notes
19
LED BILL JAM ERRORS
Bill Jam Errors indicate bill movement issues through the iVIZION® Unit. Jam
Errors are indicated by a flashing Yellow LED. By counting the flashes inbetween the pause states, the error can be determined and located in 
Table 6 below.
Table 6 LED Jam Error Codes
LED
Color
Yellow
Status LED
Flash No.
Error Type
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Reserved
Entrance Sensor Jam
CIS Sensor Jam
Exit Sensor Jam
Feed-In Sensor Jam
Feed-Out Sensor Jam
Cash Box Jam
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
N/A
Check/Clean the Entrance Sensor
Check/Clean the CIS Sensor
Check/Clean the Exit Sensor
Check/Clean the Feed-In Sensor
Check/Clean the Feed-Out Sensor
Check for Jammed Note in Cash Box
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
July, 2014
JCM USB TOOL SUITE OVERVIEW
JCM TOOL SUITE FUNCTIONS - iVIZION
Functions Available
Figure 3 displays two (2) versions of an open JCM Tool Suite Device Information Screen (See Figure 3 a) with two (2) different Service Mode Pull-down
Menus (See Figure 3 b) active.
When an iVIZION® Unit is connected, the following functions are available in
the Operations Mode (See Figure 3 c):
• Download
• Statistics
• Utility (See Figure 3 e).
a
a
b
c
b
d
e
e
g
f
Figure 3 iVIZION Connected JCM Tool Suite Screens
Lecture Notes
If the iVIZION® Unit is connected to the JCM Tool Suite while in Maintenance Mode, with DIP Switch No. 8 ON (See Figure 3 d), the following 
additional functions will be available as well:
• Sensor Adjustment (See Figure 3 f)
• Performance Test (See Figure 3 g).
For complete installation and operational instructions for loading the JCM
Tool Suite Program onto your PC, refer to the JCM Tool Suite Installation
Guide available at: http://www.jcmglobal.com.
Lecture Notes
Part No. 960-100927R_Rev. 3
18
7
July, 2014
BANKNOTE ACCEPTANCE TESTS
ERROR TABLES
ENTERING PERFORMANCE MODE
LED OPERATIONAL CONDITION INDICATORS
The Banknote (Bill) Acceptance Test is performed by completing the following steps:
The iVIZION® Unit’s Multi-Color Front Panel LED always shows the current
Operational Status of the iVIZION® Unit. Table 5 lists the various color code
indications.
1. Remove power from the iVIZION® Unit being tested.
2. Place the iVIZION® Unit in Performance Mode by turning DIP Switch
a
SW1 Switch 8 ON (See Figure 4 a).
3. Apply power to the iVIZION® Unit.
4. Connect the iVIZION® Unit being
Figure 4 DIP Switch SW1
tested to a PC USB Port (USB Male
'A' to Mini-B USB Cable).
5. Start the JCM Tool Suite Application.
6. Select the Performance Test Mode.
7. Run the Acceptance Mode Test (Bill Acceptance). The screen shown in Figure 5
will appear.
Table 5 LED Operational Code Conditions
Symptoms
Power ON
LED
Normal
Condition
Initializing
Lecture Notes
Part No. 960-100927R_Rev. 3
8
Extinguished (Out) The iVIZION is set-up correctly (Stand-by).
Blue Flashes
Lit Red
Lit Green
Downloading
Near Full
Detection
The iVIZION is initializing.
The iVIZION is performing a download.
Lit Yellow
Lit Blue
Test Mode
Lit Green
Error
Red Flashes
Banknote Jam
Yellow Flashes
Reject
Green Flashes
ICB
Blue Flashes
Green LED
The iVIZION Extinguished
is not working
(Out)
Figure 5 Typical Acceptance Test Screen
Status LED
Extinguished (Out)
The iVIZION has detected a Nearly-full
Cash Box Condition.
The iVIZION status is in the “Performance
Test Mode” (Stand-by).
The iVIZION has developed an error
condition (See Table 9 Operational LED
Error Codes).
The iVIZION has a jammed Banknote (See
Table 6 Jam LED Flash Error Codes).
The iVIZION has an error condition (See
Table 7 LED Reject Error Codes).
ICB settings need to be set for proper
operation (See Table 8 LED ICB Flash
Codes).
Power is not being supplied.
[Solution]
• Ensure all Harnesses are securely connected
to their related Interfaces.
• Ensure that the Power Supply working Voltage and range is appropriate.
• Ensure the Interface Harnesses are not disconnected between the Transport Unit and
the Frame Unit.
• Ensure that the higher Interface Board Fuse
(F1) is not blown.
• Ensure that all Harnesses and/or Circuit
Board Connectors are properly seated onto
the Control CPU Board.
Lecture Notes
17
iVIZION Utility Tool
1. Connect the iVIZION to the
PC using a USB Male 'A' to
Mini-B USB cable.
2. Open the JCM Tool Suite.
3. Use the “Service Mode” dropdown Menu to Click-select
“Utility” from the selections
available (See Figure 12).
If the bill is stacked, the bill was accepted and the iVIZION® is operating properly. However, If the “Bill Acceptance Test” indicated an error, proceed to the
“Performance” Testing Mode.
The Performance Testing Mode is activated by turning DIP Switch No. 8 to its
“ON” position (Review Figure 4 a). 
The DIP Switch Block is located on the CPU Circuit Board found on the
underside of the iVIZION® Transport Assembly.
NOTE: If the “Bill Acceptance Test” was successful, proceed to the
“Cleaning” and “Software Update” Modes.
If the “Bill Acceptance Test” indicates an error while in the “Performance”
Testing Mode, refer to Table 3 to identify the error type being indicated.
Table 3 Acceptance Test Error Indications
Figure 12 iVIZION Utility Tool Screen
Select “1) CIS IMAGE” to read and display the image of the last Banknote or
Ticket accepted.
ICB SETTING
Select “2) ICB SETTING” to Enable/Disable the ICB function on an iVIZION
Unit, set the “M/C #” (Asset Number), or disable the ICB RFID Cash Box
Module.
Lecture Notes
Part No. 960-100927R_Rev. 3
July, 2014
PERFORMANCE TESTING MODE
The iVIZION Utility Tool is used to view the CIS Image of the last Banknote
or Ticket accepted, and also to Enable/Disable the ICB function.
To open the Utility Tool proceed
as follows:
CIS IMAGE
16
Note Condition
LED Color
Error Condition
Banknote was Stacked
None
The Bill was accepted, and the iVIZION® is operating properly.
Banknote was not
accepted
Green
The GREEN LED will blink a “Reject Code” set of flashes
defined in the Reject Errors Table located in the iVIZION®
Maintenance Manual or in Table 7 of this Overview.
A mechanical failure
occurred
Red
The RED LED will blink an “Operational Error Code” set of
flashes defined in the Operational Errors Table located in the
iVIZION® Maintenance Manual or in Table 9 of this Overview.
A Bill jam occurred
Yellow
The YELLOW LED will blink a “Jam Error Code” set of flashes
defined in the Bill Jam Error Table located in the iVIZION®
An Intelligent Cash Box
(ICB) Error occurred
Blue
The BLUE LED will blink an “ICB Error Code” set of flashes
defined in the ICB Error Code Table located in the iVIZION®
Lecture Notes
9
July, 2014
PERFORMANCE TESTING PROCEDURES
CALIBRATION
JCM TOOL SUITE STANDARD EDITION
WHEN TO CALIBRATE
Performance Testing
The JCM Tool Suite will be used to complete functional and sensor testing
of an iVIZION® Unit. Figure 6 illustrates a typical connected iVIZION®
JCM Tool Suite Screen with the “Service Mode” drop-down Menu active.
To begin a Performance Test proceed as follows:
1. Select “Performance Test” from the drop-down Menu (See Figure 6 a).
Sensors in the iVIZION Unit are self-calibrating. However, it is recommended
that the iVIZION Sensors be calibrated as part of an Annual Preventive Maintenance Procedure.
The “Test Item select” Screen shown in Figure 7 will appear.
2. From the “Test Item select” Screen, choose the iVIZION® functional test
desired.
c
e
a
Figure 6 Typical Connected iVIZION
JCM Tool Suite Screen
Figure 7 Typical iVIZION Test Item
Select Screen
Lecture Notes
CALIBRATING THE IVIZION
To Calibrate an iVIZION Unit, proceed as follows:
a
b
d
f
NOTE: If the Processor Board or any of the Sensors require
replacement, the iVIZION® will require re-calibration.
1. Place the iVIZION into Maintenance Mode (DIP Switch No. 8
ON).
2. Apply power to the iVIZION
Unit
3. Connect the iVIZION to the PC
using a USB Male 'A' to Mini-B
USB Cable.
4. Open the JCM Tool Suite Application.
5. Use the “Service Mode” dropdown Menu to Click-select
a
“Sensor Adjustment” from the
Figure 11 JCM Tool Suite iVIZION 
selections available (See Figure
Calibration Screen
11 a).
6. On the iVIZION Calibration Application, click on the “Start” Screen Button,
and follow the screen instructions to complete the calibration process.
NOTE: Two Calibration Reference Papers exist for use with an iVIZION
Unit. The KS-072 Paper is for use with the iVIZION Head without Bill
Guides installed; The KS-089 Paper is required if the iVIZION Head Bill
Guides are installed; but will also work on Units without Bill Guides.
See the iVIZION Operation and Maintenance Manual, Section 6 for details
concerning additional calibration procedures.
Lecture Notes
Part No. 960-100927R_Rev. 3
10
15
SOFTWARE UPDATING
July, 2014
AVAILABLE TESTS
JCM TOOL SUITE APPLICATION
The JCM Tool Suite Application is used to update software in an iVIZION®
Unit.
To update software in an iVIZION® Unit, proceed as follows:
1. Connect a USB Cable containing a Mini-USB connector at one end to its 
mating receptacle located on the left front side of the iVIZION® Unit being
updated.
2. Then connect the opposite end containing a Standard USB connector to an open,
unused USB Port on the PC containing the JCM Tool Suite Application.
3. Open the JCM Tool Suite Application.
4. Click on “Download” in the “Service Mode” drop-down Menu. 
The screen shown in Figure 10 will appear.
Figure 7 illustrates a typical iVIZION Test Screen.
Transport Motor Forward and Reverse Tests
The following two (2) tests runs
the Transport Motor in a forward
or reverse direction (See Figure 7
a).
Figure 8 illustrates the typical
Motor Test Screen that appears
when the “Transport motor Forward” test Screen Button is
selected.
• A flashing Yellow LED 
indicates a correct speed
• A constantly lit Yellow LED
indicates an incorrect speed.
Stacker Motor Forward Test
This test cycles the Stacker Motor
(See Figure 7 b).
b
a
c
• A flashing Yellow LED 
Figure 8 Typical iVIZION Transport Motor
indicates a correct Motor speed
Test Screen
occurred.
• A constantly lit Yellow LED
indicates an incorrect Stacker Motor speed occurring.
Cycle Test
This test performs a full transport/stacking of the iVIZION® Unit 
(See Figure 7 c).
Figure 10 JCM Downloader Suite Edition Version 1.02 Screen
5. Use “Browse” (See Figure 10 a) to locate the download file desired. Click to
select the file to be downloaded so it appears in the “File” Field (See Figure 10 b);
then Click on the “Download” Screen Button (See Figure 10 c).
Lecture Notes
• Normal operation is indicated when the Test LED remains OFF.
• An error condition is indicated by a flashing Red LED. If this condition occurs,
refer to the Operational Errors Table to resolve the error (See Table 9 on page 21).
Sensor ON/OFF Test
This test performs a functional test of each iVIZION® Unit Sensor 
(See Figure 7 d).
• Block each Sensor to test it. The Display with show “ON” or “OFF” indicating the
functional status of the specific Sensor blocked.
Display Check
This test cycles the LED Display on the right side of the iVIZION® Unit 
(See Figure 7 e).
• The LEDs will continuously cycle through Red, Green & Blue colors.
DIP Switch ON/OFF Test
This tests the functional operation of each switch located on the 8-position DIP
Switch Block located on the Transport Assembly (See Figure 7 f).
• Turn all DIP Switches ON to perform the DIP Switch Test. All switches should
indicate “ON”. Remove the Transport and change DIP Switches 1 through 7 to
“OFF” but leave Switch 8 “ON”. Re-run the test; switches 1 through 7 should indicate “OFF”.
Part No. 960-100927R_Rev. 3
14
11
CLEANING AND PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE
Proper cleaning is critical to maintaining a high acceptance rate on an 
iVIZION® Unit.
Clean all Sensors shown in Figure 9 using a dry, lint free cloth ONLY. 
The identity of each Sensor is listed in Table 4 on page 13 of this document.
NOTE: Do not use Alcohol, Solvents, Citrus Based Cleaners or
Cleaning Cards on an iVIZION® Unit. Use of these compounds will
damage the Unit’s Lens Surfaces. DO NOT use JCM Cleaning Cards
intended for use with the UBA or WBA Units either, the cleaning
solution on them is not compatible with the iVIZION® Unit’s Sensors.
n
c
e
o
f
g
p
b
k
Hidden
a
d
q
h
Hid
de
m
j
l
n
Hid
de
n
i
r
Figure 9 iVIZION Sensor Locations
July, 2014
SENSOR IDENTIFICATION
Table 4 identifies the purpose of each Sensor located in Figure 9 on page 12 of
this document.
Table 4 iVIZION Sensor Cleaning Location Types
Sym.
Sensor
Cleaning Method
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
Entrance Sensors
Exit Sensors
UV Sensor (Upper)
Acceptor Unit
UV Sensor (Lower)
Transmissive Sensor
CIS Sensor (Upper)
CIS Sensor (Lower)
Feed-in Sensors
Feed-out Sensors
Home Position Sensor
Transport Unit
Home Position Sensor Lens
Nearly Full Sensor
Cash Box Sensor
Home Position Sensor Lens
Cash Box
Cash Box Sensor Lens
Nearly Full Sensor Lens
Anti-Stringing Mechanism
Feed-in Sensor’s Comb Grooves
Wipe area clean
using a lint-free
cloth such as a
Micro-Fiber Cloth,
or blow clean using
Compressed Air.
NOTE: Refer to the iVIZION Preventive Maintenance Procedure
Guide (JAC P/N 960-100932R) for more information.
Lecture Notes
Lecture Notes
Part No. 960-100927R_Rev. 3
12
13

JCM Global® iVIZION® Banknote Validator Training Overview

Transcription

Similar documents

Two forces working with the weather…

Membership Brochure - Email and Web Version_Layout 1

The idea with modifying stock down pipes is to gut the pre

iSCOUT PRS80

your seventh sense - L

ASSURANCE - Sensaphone

Wireless Sensor Troubleshooting Guide

Mid-Semester Presentation 2.27 MB Wednesday, October 24, 2012

RAMOS Ultra EX-D8-8 User Manual

Bulletin BPI-01 - Raybestos Brakes

Epitypification of Graphium penicillioides Corda, with