warning

[R1]
Installation TopFix / RecessFix [R1]
Do not damage the product when using a sharp knife to open use the original screws enclosed, to prevent malfunctioning
the packaging! Fitting screws: Use a size-2 screwdriver (PO- from using too thick screw heads!
ZIDRIVE) or use an electric screwdriver at it’s lowest torque.
Rail removal: Use a flat screwdriver of max. 6 mm wide. Only
Model
25/AU30
25/AU31
WARNING
reach of young children. Move beds, cots and furniture away from window covering cords.
Do not tie cords together. Make sure cords do not twist and create a loop. Install and use
the included safety devices according to the installation instructions on these devices to
Young children can be strangled by loops in pull cords, chains, tapes and reduce possibility of such an accident. According to EN 13120
inner cords that operate the product. They can also wrap cords around
their necks. To avoid strangulation and entanglement, keep cords out of
Installation and User’s manual PB - GB
Product width
Number of parts
30 - 90 cm
2
2
90 - 180 cm
3
3
180 - 270 cm
4
4
270 - 300 cm
5
5
25
max. 80 cm
x
x
37
52
28
X=5 cm
Clip installation
Adjust control height
To lower the shade
To raise the shade
1
3
4-A
4-C
1.5m
14-10-2014
15
Installation
2
For installation height from 1.5m,
the tassel must be at least 1.5m
from the floor. To adjust the tassel
height, push the tassel cap up the
cord and tie a knot on the required
height. Then cut the cord under
the knot and click the enclosed
transparent part of the tassel on
the cap.
1
For installation height on/below
1.5m, the operation cord length is
max 1cm. To adjust the operation
cord length, push the tassel cap
up to the headrail. Tie a knot as
high as possible, then cut the
cord under the knot and click the
enclosed transparent part of the
tassel on the cap.
6
2
*
3
Click
To lower the shade
Removal
4-B
Rail installation sequence on Clips
2-A1
2-A2
B
4
C
Click
Subject to technical changes
5
A
Installation and User manual:
146
[F1]
FaceFix installation to a window frame / wall [F1]
Do not damage the product when using a sharp knife to open use the original screws enclosed, to prevent malfunctioning
the packaging! Fitting screws: Use a size-2 screwdriver (PO- from using too thick screw heads!
ZIDRIVE) or use an electric screwdriver at it’s lowest torque.
Rail removal: Use a flat screwdriver of max. 6 mm wide. Only
Model
25/AU30
25/AU31
WARNING
reach of young children. Move beds, cots and furniture away from window covering cords.
Do not tie cords together. Make sure cords do not twist and create a loop. Install and use
the included safety devices according to the installation instructions on these devices to
Young children can be strangled by loops in pull cords, chains, tapes and reduce possibility of such an accident. According to EN 13120
inner cords that operate the product. They can also wrap cords around
their necks. To avoid strangulation and entanglement, keep cords out of
Installation and User’s manual PB - GB
Product width
30 - 90 cm
2
2
90 - 180 cm
3
3
180 - 270 cm
4
4
270 - 300 cm
5
5
max. 80 cm
x
Number of parts
x
37
52
28
X=5 cm
15
Clip installation
Adjust control height
To lower the shade
To raise the shade
1
3
4-A
4-C
1.5m
14-10-2014
28
Installation
2
For installation height from 1.5m,
the tassel must be at least 1.5m
from the floor. To adjust the
tassel height, push the tassel
cap up the cord and tie a knot on
the required height. Then cut the
cord under the knot and click the
enclosed transparent part of the
tassel on the cap.
1
For installation height on/below
1.5m, the operation cord length is
max 1cm. To adjust the operation
cord length, push the tassel cap
up to the headrail. Tie a knot as
high as possible, then cut the
cord under the knot and click the
enclosed transparent part of the
tassel on the cap.
6
2
3
*
Click
To lower the shade
Removal
4-B
Rail installation sequence on Clips
2-A1
2-A2
B
4
C
5
Click
Subject to technical changes
A
Installation and User manual:
147