Cold Milling Machine W 250 i
Transcription
Cold Milling Machine W 250 i
World class in performance and productivity Cold Milling Machine W 250 i High-performance cold milling machine – designed with sheer efficiency in mind No other milling machine is equal to greater challenges in road construction Maximize productivity while minimizing o perating costs – this maxim is the key for construction projects that require large pavement areas to be milled at record speed. Tremendous engine power makes the W 250 i highend cold milling machine from Wirtgen a top performer which completes even the toughest jobs with maximum efficiency. But the large milling machine has even more to offer: the WIDRIVE machine management system, which greatly improves operator comfort, guarantees low fuel consumption rates while enabling an environmentally compatible milling process. It goes without saying that, owing to its innovative dual-engine concept, the W 250 i is a role model in economy during phases in which performance requirements are low. The W 250 i excels in the quick completion of large-scale milling projects A machine that lets performance speak for itself The large milling machine is removing the pavement at high advance rates Tremendous milling performance State-of-the-art machine management and maximum drive power. WIDRIVE Intelligent machine management system for low operating costs. Dual-engine concept Milling with one engine at 447 kW / 600 HP / 608 PS or two engines at 739 kW / 991 HP /1,005 PS. Smart ISC travel drive system Traction control, power control, precise maneuvering in bends. Six different milling widths Milling widths ranging from 7’ 3” to 14’ 5” (2.20 m to 4.40 m). 2 // 3 Unlimited milling performance Unrivalled in the large milling machine class Each type of pavement removed by the W 250 i is instantly crushed into small-sized material by the top-performing machine at tremendous advance rates as two ultra-strong diesel engines flex their muscles. M illing extensive areas on roadways or airports is therefore not a problem at all. The machine’s intelligent WIDRIVE anagement system, state-of-the-art dual-engine concept m and choice of different engine or milling drum speeds are extremely useful features on such high-profile, large-scale construction projects: they contribute to significantly reducing the overall operating costs. Advance rate - ft/min (m/min) 230 (70) 213 (65) 197 (60) 164 (55) 164 (50) 148 (45) 131 (40) 115 (35) 98 (30) 82 (25) 66 (20) 49 (15) 33 (10) 17 (5) 0 Milling depth 012 3 45 678910 1112 13 14 inches (25) (50) (75) (100)(125) (150)(175)(200)(225) (250) 275) (300)(325)(350) (mm) Engine speed = 1,600 min-1 Engine speed = 1,900 min-1 Engine speed = 2,000 min-1 Milling performance at 7’ 3” (2.2 m) milling width Its tremendous engine power makes the W 250 i the ideal candidate for milling pavements at depths of up to 14” (350 mm) or hard concrete pavements at high advance rates. Beyond the highly efficient milling of individual layers, complete road pavements can also be removed in a single machine pass. Optimum organization of trucks enables the W 250 i to remove up to 1,200 tons per hour of asphalt – which is equivalent to the payload of 60 trucks. The high-performance W 250 i is also the ideal choice for large-scale projects that need to be completed on schedule under tremendous deadline pressure. 4 // 5 Optimum milling performance – whatever the job Choice of three different milling drum speeds A clever feature assists the machine operator in optimizing diesel fuel consumption, milling performance and thus the overall efficiency of the W 250 i: adjustment of the milling drum speed from the operator’s platform. It guarantees optimal milling performance levels regardless of conditions and across a wide range of applications. The W 250 i usually runs at the medium milling drum speed when carrying out standard milling jobs, such as milling a surface course. High speed is selected for the large-scale milling of thin pavement layers. Low speed is the right choice if maximum milling performance levels are to be achieved at the lowest possible cost: it guarantees reduced fuel consumption rates and low cutting tool wear. Manual adjustment of the milling drum speed – enabling the machine, when working in ECO mode at low engine speed ... More power, less fuel … to efficiently remove complete road pavements down to a depth of up to 14” (350 mm) A selector switch in the operator’s platform enables the engine or milling drum to be set to three different speed levels. Medium milling drum speed ensures a favorable particle size of the milled material and should be selected for surface course milling jobs. Low milling drum speed is recommended if high milling performance levels are required at low milling costs, for instance, when removing complete pavements at full depth. High milling drum speed at high advance rates ensures an excellent surface texture in fine milling jobs. 6 // 7 High-tech – yet easy to operate Controlling the W 250 i with ease The innovative operating concept installed in the W 250 i supports the operator and keeps him upto-date on everything he needs to know. The control panels on the left and right have identical features and are individually adjustable, thus allowing ease of operation on both sides of the machine. Together with the LEVEL PRO control panel, the multifunctional control screen can be swivelled to both sides to always face the machine opera- tor. It informs the operator about all important machine and operation parameters. All controls are located within easy reach and in the operator’s field of view. They are labelled in a language-neutral manner and allow easy and intuitive operation. In the final analysis, the operator is familiar with the W 250 i very quickly, enabling him to fully focus on the milling process and deliver top performance. A small number of buttons and switches … and right ensure ease of operation The W 250 i offers great clarity, a small number of controls and adjustment to personal preferences Control panels with identical features left … The number of controls has been minimized as the intelligent WIDRIVE machine control system takes care of many tasks previously performed by the machine operator. The clearly arranged controls are ergonomic in design and help to prevent fatigue during work. Ground personnel can use control panels mounted on the sides of the machine to set or modify important parameters, such as the milling depth. Lockable, break-proof covers protect all of the control panels against vandalism. 8 // 9 Multifunctional control screen Giving operators the full picture – at all times Operation parameters: Job data: The control screen is mounted in the operator’s immediate field of view … Diagnostics: … and displays operation parameters, job data or diagnostic details clearly and in color Making easy work of any job The multifunctional control screen provides clear information on operation parameters and maintenance details. User-friendly diagnostic tools with clear, unambiguous graphic displays enable comprehension of the diagnostics procedures after only a short training period. Another feature is the continuous logging of events during the entire milling process. After keying in the material density and milling width, the control system automatically displays information such as the weight and volume of the material milled, the size of the area milled or the number of trucks loaded. These job parameters allow the quick and easy settlement of projects and provide reliable logging of daily performance. WIDRIVE – technology designed with people in mind Engine station Automatic speed adjustment in accordance with the milling process to lower diesel fuel consumption Dual-engine design: the second engine is switched on and off automatically Loading of milled material Consistently high belt speed in case of engine lugging Belt is switched off automatically during reversing and in transport mode Travel drive ISC (Intelligent Speed Control) offers optimized machine advance rate, traction control and adjustment of the track speed in bends Milling drum assembly Automatic raising of side plates, gradation control beam and scraper in transport mode Height adjustment Four-fold full-floating axle LEVEL PRO leveling system PTS (Parallel To Surface) WIDRIVE is an intelligent machine management system. It automatically manages numerous steps in the control of the W 250 i which normally need to be performed by the machine operator. WIDRIVE links various machine functions, such as diesel engines, travel drive, milling drum drive and conveyor drive, water spray system, automatic PTS system as well as LEVEL PRO leveling system, thus Water system Switches on and off automatically Water feed adjustment depending on engine load enabling the operator, who is relieved of much of his previous workload, to fully focus on the quality of his work. The intelligent linking of these machine functions pays for the customer in terms of significantly reduced diesel consumption rates, faster processes, reduced water demand, low engine noise levels and increased daily production rates. 10 // 11 Perfect visibility and unmatched operator comfort The so-called “wasp waist” design enables a free view of the milling cut Ergonomic working in both upright and seated position Perfect working environment ensures maximum effectiveness The spacious operator’s platform is fully equipped to enable ergonomic working in line with practical requirements and over extended periods of time. The recessed chassis contour – or s o-called “wasp waist” design – of the W 250 i provides the machine operator with a full view of the front right track unit, milling edge and edge protection plates. He also has an excellent view, in both upright and seated position, of the controls and everything that is happening on the construction site. The vibration-isolated operator’s platform is accessed conveniently via access ladders fitted on both sides. It is equipped with individually adjustable comfort seats, a hot-air blower and a protective canopy that is fully movable to the left or right side. All of these features make for perfect working conditions. Overview of cameras: 6 2 1 3 4 5 1 Camera at the rear 2 Camera at end of conveyor 3 Camera at scraper 4 Camera front, centre 5 Camera front, right 6 Camera front, left The multifunctional control screen can be switched to camera mode to monitor important work processes. Two or six high-resolution color cameras can be installed in accordance with customer specifications. When using six cameras, an additional camera screen is installed to allow the simultaneous display of two different camera views. Optional installation of an intelligent data converter enables defined machine parameters to be read out from the machine’s control system as per the standardized WIFMS norm. 12 // 13 LEVEL PRO guarantees high-precision milling results “Rapid slope” – the electronic cross slope sensor for the milling of predefined cross slopes Displacement sensors in the hydraulic cylinder accurately capture the milling depth Geared up for the future with state-of-the-art technology An accurate leveling system is essential for achieving a perfect working result. Wirtgen has developed a specific leveling system for use with cold milling machines: LEVEL PRO. The overall system comprises various sensors, a controller unit and a separate control panel. The graphics-enabled LEVEL PRO screen provides a clear readout of key parameters. Set and actual values for the left and right milling depth as well as cross slope parameters are clearly shown on the displays as work progresses. In addition, the memory feature is very useful to program, store and invoke set values. Multiplex system: two ultrasonic sensors plus the sensors mounted at the side plates capture the milling depth Hydraulic milling depth sensors capture the level in front of the milling drum ● ● ● ■ ■ Black Blue Red Yellow Green = = = = = slope sensor sensor scanning in front of the drum permanently installed sensor socket for ultrasonic sensor, wire-rope sensor etc. socket for LEVEL PRO control panel Two lifting cylinders with integrated displacement sensors capture the milling depth at the edge protection plates on both sides of the machine. LEVEL PRO can be easily extended, for instance, by the multiplex system, laser leveling, or 3D leveling which uses the interface included in the system. A great variety of sensors can be integrated into the automatic leveling system, such as hydraulic milling depth, cross slope and ultrasonic sensors. The multiplex system analyzes the measuring points of three sensors on each side of the machine – very useful to ensure perfectly level surfaces. 14 // 15 Unrivalled power – optimized environmental protection State-of-the-art engine technology Two separate ultra-performance diesel engines enable the W 250 i to mobilize unparalleled milling performance whenever required. In addition to the innovative dual-engine concept, the large milling machine offers an exceptionally efficient energy balance while keeping the strain on the environment low. For the two economical engines can be operated at three different speed levels to efficiently respond to the specific job requirements. The fully electronic WIDRIVE machine management system enables both engines to always work in the optimal performance and torque ranges, at extremely low fuel consumption rates and low operating costs. 1 Combined two-way catalytic converter and diesel particulate filter 2 Special “direct-flow” air filters 3 Diesel engines 1 + 2 with cooled exhaust gas recirculation and variable turbocharger geometry 2 1 3 M [Nm] 5000 4500 4000 3500 3000 2500 2000 1500 1000 500 0 P (kW) 800 720 640 560 480 400 320 240 160 80 0 900 Engine output using two engines Engine output using one engine Torque using two engines Torque using one engine Engine speed = 1,600 min-1 Engine speed = 1,800 min-1 Engine speed = 2,000 min-1 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 [1/min] The W 250i features state-of-the-art engine technology for lowest environmental emission levels, complying with the stringent specifications of exhaust emission standards EC Stage 3b / US Tier 4i. To ensure effective exhaust gas purification, both engines of the W 250i are equipped with a two-way catalytic converter integrated into the diesel particulate filter. Combined with an effective sound insulation of the engine compartment, the quiet ECO engines guarantee low noise emission levels. The operator is protected from vibrations as both engines are supported and isolated from vibration by silent blocks. 16 // 17 State-of-the-art dual-engine concept It takes two to boost economic efficiency Wirtgen is the first cold milling machine manufacturer worldwide to offer uncompromising performance characteristics and maximum efficiency by connecting two diesel engines by means of a multiple V-belt. Taken together, the two engines provide tremendous power, enabling the W 250 i to achieve unmatched performance levels. Only engine 1 is in operation in those conditions where the performance level required to achieve the specified results is low. This offers significant advantages: deactivating engine 2 results in lower noise levels, lower fuel consumption and therefore lower exhaust gas emission levels. Tailoring performance to economical fit Engine 1 Engine 1 is running in all operating conditions. Manual selection of engine 2 via the ignition switch Engine 1 Engine 2 Engine 2 is switched on or off depending on requirements. Economical drive concept: two combustion engines While engine 1 drives all functional groups, engine 2 is switched on automatically or at the flick of a switch for full milling power. The operator decides for himself whether to switch off engine 2 when performing milling operations at partial load. Engine 2 is switched off automatically in certain situations, for example, when initiating the transport mode or when stopping the traction drive for three minutes or longer. Switching on engine 1 only is often sufficient for milling off a surface course at a depth of 1.5” (4 cm). 18 // 19 PTS – always parallel to the road surface If one of the crawler tracks hits an obstacle (such as an elevated milling edge) during the milling operation, the other three track units contribute to compensating the level offset, thus enabling the level compensation to occur much more rapidly. Finely tuned compensation of surface irregularities Why does the W 250 i always maintain its stability, whether during the milling process, when simultaneously lowering all four lifting columns, when lowering the rear track units into the milling cut, when altering the milling depth, in case of surface irregularities on the left or right side, or when in transport mode? The solution is PTS. The intelligent automatic system aligns the machine parallel to the road pavement: any surface irregularities are compensated dynamically via the machine’s four hydraulically inter-connected lifting columns. This feature provides the W 250 i with a high level of stability in both longitudinal and transverse direction, relieves the operator from the need for manual adjustment and improves the overall leveling quality. In short – it makes the milling process much more efficient. ISC – the intelligent travel drive system Crab steering permits the achine to easily approach m the milled cut from the side Narrow radii, a ccurate and fast steering maneuvers Large steering angles of the four track units enable surprisingly small turning radii When a large milling machine is required to be highly maneuverable or make swift headway on difficult ground, the turn of the W 250 i fits the bill. This is attributable to the hydraulic all-track steering system, freely selectable steering modes, suspension units with separate hydraulic height adjustment or continuously adjustable travel speed as well as the intelligent ISC track control sys- tem. It includes three basic features: an electronic traction control system to ensure optimal traction, automatic speed adjustment of the individual track units in bends to reduce track pad wear, and an optimized advance rate to ensure maximum milling performance at all times. 20 // 21 On the road of success with mature Wirtgen milling technology Hard-wearing HT22 quick-change toolholder system included Wirtgen has continually developed and improved the milling process in accordance with strict rules. Our greatest strengths are extensive manufacturing expertise, knowledge in the use of high-quality, highly wear-resistant materials and optimal, application-specific positioning of the cutting tools on the milling drum. The cutting tools guarantee optimal milling performance, a highly precise milling texture and low-vibration operation of the machine. The broad range of different types of milling drums enables an equally broad range of applications. In addition, the wear-resistant HT22 quick-change toolholder system ensures extended, highly effective milling intervals. All in all, Wirtgen milling drums contribute to significant time and cost savings in tough everyday operation on the job site. Intelligent tool arrangement in a helical pattern – cutting tools tailored to the specific milling job Simple replacement of cutting tools Quick replacement of cutting tools, drum turning device, ejectors suitable for multiple use The HT22 system is distinctive for its exceptionally high durability, optimized tool rotation and significantly extended service intervals. The milling drum turning device moves the milling drum into the ideal position in forward or reverse mode with the diesel engine switched off. The innovative hydraulic tool extractor can be operated effortlessly with the diesel engine switched off. Ejectors made of highly wear-resistant steel can be turned about 180° and thus be used twice. 22 // 23 Wide range of applications: milling widths from 7’ 3” to 14’ 5” (2.20 m to 4.40 m) Six different milling width options offered: W 250 i with 7’ 3” (2.2-m) drum assembly W 250 i with 8’ 2” (2.5-m) drum assembly The following are additionally available: Drum assembly with a working width of 10’ 2” (3.1 m) Drum assembly with a working width of 11’ 6” (3.5 m) Drum assembly with a working width of 14’ 5” (4.4 m) W 250 i with 12’ 6” (3.8-m) drum assembly Cost and quality benefits through XXL-size milling drum units To fully exploit its tremendous milling potential, a housing extension enables the W 250 i to be equipped with milling drums of up to 14’ 5” (4.40 m) in width. Milling drum units wider than 7’ 3” (2.20 m) pay for themselves quickly through tremendous area performance levels as they enable wide road pavements to be removed in a single machine pass. The oversized drum units play their trump cards in particular on wide urban roads, roadways, highways and airports. In addition, the milled surfaces impress with perfect evenness. This results in enormous saving potentials as a process using greater milling widths reduces the number of adjacent cuts and of the turning maneuvers required while also driving down labor cost. Removing an 4” (11 cm) thick surface and binder course of hard asphalt material using the 7’ 3” (2.2-m) ECO cutter 7’ 3” (2.2 m) drum assembly with FCS Light FCS Light for a multitude of applications at a milling width of 7’ 3” (2.2 m) ECO cutter Milling width: Milling depth: Tool spacing: 7’ 3” (2.2 m) 0-14” (0 -350 mm) 1” (25 mm) Fine milling drum Milling width: 7’ 3” (2.2 m) Milling depth: 0-4” (0 – 100 mm) Tool spacing: 5/16” (8 mm) Standard milling drum Milling width: 7’ 3” (2.2 m) Milling depth: 0-14” (0 -350 mm) Tool spacing: 5/8” (15 mm) Micro-fine milling drum Milling width: 7’ 3” (2.2 m) Milling depth: 0-1” (0 – 30 mm) Tool spacing: 1/4” x 2 (6 x 2 mm) Fine milling and micro-fine milling drums are fitted with cutting tools arranged at a much narrower tool spacing than standard milling drums. Fine milling and micro-fine milling drums enable road pavements to be roughened and their evenness and tire adhesion to be improved. Fine milling and micro-fine milling drums create finely textured surfaces which are ideally suited as a base for the application of thin pavement layers. They additionally enable the cross slope of a road pavement to be altered or coatings to be removed. 24 // 25 Milling drum unit with many useful features Set the scraper blade to “floating” position to allow full loading of the milled material … promotes favorable particle sizes and prevents the formation of large slabs Lock the scraper blade at the required height for partial loading of the milled material The hydraulically lifting gradation control beam protects the belt from damage, … Milling flush to curb right down to the full working depth An intelligently designed milling drum unit is part of the W 250 i’s equipment package. For full loading of the milled material, the operator lowers the scraper blade hydraulically. When raised and locked at the required height, the scraper blade enables the milled material to be either partially loaded or remain in the milled cut. In addition, the scraper blade can be swung wide open for the replacement of cutting tools. The edge protection plates left and right are raised via hydraulic cylinders to precisely mill along road fixtures. Raising the edge protection plates also prevents them from digging into the ground in unpaved areas. To prevent collisions during maneuvering, the gradation control beam, scraper blade and side plates are raised when in transport mode. Yet another extra feature: in emergency mode, all cylinder functions can be operated even with the engine switched off. The left edge protection plate can be raised by 14” (350 mm), the right one by as much as 18” (450 mm) Accurate milling along curbs is possible on the right side even at maximum milling depth Yet another highlight: the edge protection plate on the right machine side can be raised by 18” (450 mm). Accurate milling flush to curb is thus also ensured at great working depths, enabling the edge protection plate to move over the curb for the purpose of level detection. 18” (450) 14” (350) 14” (350) 14” (350) Dimensions in inches (mm): Two separate water spray bars ensure optimal tool cooling, with the water pressure being adjusted in accordance with the machine’s performance and the amount of water being continuously variable. This feature extends tool durability and effectively reduces the generation of dust. 26 // 27 Removing huge amounts of milled material The loading conveyor fills large dump trucks in record time Wide conveyor slewing angles of 60° to either side ensure smooth material transport Reliable material loading even under full load The powerful W 250 i has been designed for maximum performance and is therefore equipped with a conveyor system offering exceptionally high conveying capacities. The swivel-mounted and height-adjustable discharge conveyor enables tremendous amounts of milled material to be loaded onto trucks in the most flexible and cost-effective manner. This is of particular advantage when working in narrow bends or crossroad areas and to ensure that trucks can change “on the fly”. The conveyor system can be continuously adjusted to different belt speeds as required by the milling job. Useful for night work: the optional stoplight system gives silent “Stop” and “Go” instructions to the truck driver Continuously adjustable belt speed and discharge range High belt speed Low belt speed The belt speed can also be adjusted manually to achieve perfect distribution of the milled material on the truck by setting a variable discharge pattern. Wear of the primary conveyor is minimized as the belt speed is controlled automatically in accordance with the load. Optimizing the belt speed guarantees minimum wear of the belts which have rugged cleat profiles. A stoplight system integrated in the electrically adjustable, fold-in exterior mirrors enables visual communication with the truck driver without needing to revert to audible signals. 28 // 29 Vacuum cutting system offers a high level of operator comfort Innovative extraction technology offers a free view of the milling edge The health and well-being of the operating crew deserve particular attention. The W 250 i can therefore be equipped with the vacuum cutting system to extract fine material particles: by creating a negative pressure in the milling drum housing, the mix of air and water vapor is evacuated and, via a hose system, fed back into the flow of the milled material transported on the discharge conveyor. Better air quality and visibility in the working environment of the machine operator and ground crew significantly improve operator comfort and boost staff performance. In addition, reduced soiling of components such as the engine or air filter results in savings in the replacement of spare parts or cleaning of the machine. Quick maintenance boosts productivity For peace of mind in operation The engine cowling opens hydraulically at the mere push of a button Maintenance diagnostics and parameter settings via the on-board control panel Replacing the air filter is simple and can be performed from the operator’s platform The hydraulically opening, hinged engine cowling and wide-opening service panels on either side ensure full access to all points of maintenance. The machine’s automatic diagnostic system indepen dently monitors valves, sensors and control components. All points of maintenance have been grouped together and are arranged in a clear pattern, offering convenient access. Ample space is available for storing spare cutting tools, tool kit, machine equipment and high-pressure cleaner. 30 // 31 Successful moves in night operation Excellent lighting enables night operations to be completed quickly and efficiently All clear even in darkness – backlit control panels Wasting no time during night operations The W 250 i calls it a day only after it has successfully completed its daily work – which is not a problem at all even in darkness. The machine puts up an equally compelling performance during the night and in broad daylight. The lighting system comprises several spotlights and LED lights offering flexible adjustment options to fully illuminate the important work areas. Backlit control panels enable the machine operator to easily control the W 250 i even during night operations. And we don’t want to forget the smart “Welcome” and “Go home” lights feature: when walking away from the W 250 i, it fully illuminates the surroundings of the machine. Heavy-duty transport made easy The control console can be pivoted down to facilitate transport Transport – a smooth affair The folding conveyor reduces the machine’s transport length Transport on a flatbed truck with the optional canopy folded down – tailored to accurate fit! The folding conveyor design reduces the overall length of the W 250 i, thus permitting the use of smaller transport vehicles. The optional canopy is folded down to transport height hydraulically at the mere push of a button. Our range of equipment options includes conveyor support legs for machine transport on a flatbed truck. Supplementary weights allowing flexible use enable transport of the W 250 i on vehicles with a low maximum permissible payload. 32 // 33 Keeping a firm eye on environmental standards Significant reduction of environmental emission levels The W 250 i large milling machine performs extremely hard work, yet also successfully meets the challenge to comply with ever stricter environmental and health requirements. Users of the W 250 i have a clear ecological conscience thanks to the intelligent WIDRIVE machine management system, for WIDRIVE not only significantly reduces diesel consumption rates but also minimizes exhaust gas emissions, noise levels and engine vibrations. The machine’s dual-engine concept is a vital element of the WIDRIVE system as it offers the unbeatable advantage of simply shutting down the second engine, when not needed, for fuel economy. Exhaust and noise emission levels are reduced at the same time – to keep the environment intact. The W 250i delivers a clean job in terms of efficiency and environmental compatibility Reduced diesel consumption Economical operation, low environmental impact, efficiently performing staff The two engines installed in the W 250 i comply with the strict specifications of exhaust emission standards EC Stage 3b / US Tier 4i. Noise emission is reduced by the efficient soundproofing of the engine compartment and anti-vibration engine support. The effective VCS extraction system used to evacuate fine material particles reduces dust emission in the area of the milling drum housing. Different engine or milling drum speeds, which can be selected in line with the milling job, ensure exceptionally low fuel consumption. 34 // 35 Wirtgen America Inc. 6030 Dana Way · Antioch, TN 37013, USA Phone: (615) 501-0600 · Fax: (615) 501-0691 Internet: www.wirtgenamerica.com Illustrations and texts are non-binding and may include customized fittings. Subject to technical changes. Performance data depend on operational conditions. No. 2176174 14-10 EN-09/12 © by Wirtgen GmbH 2012 Printed in Germany Illustrations and texts are non-binding and may include customized fittings. Subject to technical changes. Performance data depend on operational conditions. No. 2311330 23-10 US-04/13 © by Wirtgen GmbH 2013 Printed in Germany
Similar documents
Cold milling machine W 50 DC / W 50 DC i
FCS: The efficient success formula for utilizing your milling machine’s full capacity A lucrative job cannot be taken on because the right machine is not available? Wirtgen’s Flexible Cutter System...
More information