2007 Suzuki GSXR1000 Dynojet Research 2191 Mendenhall Drive
Transcription
2007 Suzuki GSXR1000 Dynojet Research 2191 Mendenhall Drive
2007 Suzuki GSXR1000 I n s ta l l a t i o n I n s t r u c t i o n s Parts List 1 Power Commander 1 CD-ROM 1 Button Adjustment Display USB Cable 1 Installation Guide 1 Power Adapter 2 Power Commander Decals 2 Dynojet Decals 2 Velcro ® 1 Strip Wire tap 1 Alcohol Swab 1 Faceplate Buttons O2 eliminator Expansion Port USB Port The ignition MUST be turned OFF before installation! You can also download the Power Commander software and latest maps from our web site at: www.powercommander.com PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION Dynojet Research 2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com i333-411 www.powercommander.com 2007 Suzuki GSXR1000 - 1 Fig. A 1 Remove the seats. 2 Prop the fuel tank up. 3 Lay the PCIII in the tail section and route the PCIII harness towards the Fig. B front of the bike (Fig. A). PCIII Ground wire harness 4 5 Route the PCIII harness along the left hand side of the bike. Attach the ground wire from the PCIII to the negative side of the battery (Fig. B). Fig. C 6 Unplug the stock wiring harness from the lower injectors (Fig. C). Unplug i333-411 www.powercommander.com 2007 Suzuki GSXR1000 - 2 7 Plug the PCIII wiring harness in-line of the stock harness and injectors (Fig. D). Do NOT connect the PCIII harness to the upper injectors. Make sure you Fig. D are on the set of injectors that is below the fuel rail. ORANGE - #1 cylinder YELLOW - #2 cylinder GREEN - #3 cylinder BLUE - #4 cylinder 8 Unplug the stock wiring harness from the Throttle Position Sensor (Fig. E). This will allow easier access to the Fig. E wires. 9 Crimp the supplied wire tap to the 10 Connect the GREY wire from the PINK/BLACK wire. PCIII to the wire tap (Fig. F). It is recommended to use dielectric grease on these connections. Unplug this connector 11 Connect the stock wiring harness back 12 Secure the PCIII in the tail section Wire tap on to the TPS using the supplied velcro. Make sure to use the alcohol swab to clean both Fig. F surfaces before attaching. 13 Lower fuel tank and reinstall seats. 14 Locate the stock O2 sensor which is on the left hand side of the bike. Follow the wires out of the exhaust to the stock wiring harness. Unplug the sensor from the stock wiring harness. Grey wire from PCIII i333-411 www.powercommander.com 15 Plug the Dynojet O2 eliminator into the stock wiring harness. The stock sensor is no longer needed. 2007 Suzuki GSXR1000 - 3
Similar documents
2008 Suzuki GSXR750
Parts List
Button Adjustment Display
Power Commander
USB Cable
CD-ROM
Installation Guide
Power Adapter
Power Commander Decals
Dynojet Decals
Velcro® Strip
Alcohol Swab
Faceplate Buttons
Wire tap
O2...
2007 Suzuki SV 650 Dynojet Research 2191 Mendenhall Drive
Dynojet Research 2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
i337-411
please read all directions before starting installation
If your application has a speed sensor then
you can tap into the signal side of the sensor
and run a wire into this input. This will allow
you to calculate gear position in the Control
Center Soft...