HEIM Rousselle PDF Set - Your Equipment Source, Inc

HEIM Rousselle PDF Set - Your Equipment Source, Inc

Single Point Gap Frame • 15 to 110 Tons
Rousselle Single Point Gap Frame (Cast Iron)
Standard Features
• Cast Frame
• Air Clutch and Shoe Brake
• Crankshaft Motion (40 Ton and Up)
• Eccentric Shaft Motion (15 and 25 Ton Models)
• Wrist Pin Connection
• V Gibbing
• Air Counterbalance System (60 Ton and Up)
• Bolster Plate
• Manual Grease Lubrication
• Solid State Press Control (ANSI B11.1)
• Nema 12 Enclosure Mounted on Press
• Operator Station with Dual Run, Emergency Stop
•
•
•
•
•
•
•
and Stop on Top Palm Buttons
Supervisory Key Selector Switch for Off, Single Stroke,
Inch or Continuous Mode
Brake Monitor
Motion Detector
Dual Air Valve
Pressure Switches for Clutch/Brake and
Counterbalance
Forward/Reverse Feature
Stroke Counter
Optional Features
• One Shot Lubrication System
• Self-Monitoring Automatic Lubrication System
• Stroke Lengths other than Standard
• Additional Shut Heights
• T-Slotted Bolster
• Bolster Burnout
• Special Drilling and Machining
• Die Cushions
• Pneumatic Flywheel Brake
• Shaft Extension
• Custom Speeds
• Variable Speed Drive
• Bar Turnover with Key Selector Switch
• Pedestal for Operator Station
• Tonnage Monitor
• Remote Mounted Controls
• Additional Operator Station
Model 6A
Specifications
Model Number
2/2E
3/3E
4/4E
6A
8
10
15
25
40
60
85
110
16 ⁄4 x 11
20 x 14
26 x 16
30 x 18
36 x 24
40 x 28
160
135
105
110
100
90
–
–
45
50
50
45
Bolster Thickness
3 1⁄2
4
Slide Adjustment
Capacity (Tons) Near B.D.C.
Bed Area (Left-to-Right x Front-to-Back)
1
Non-Geared
Strokes
Per Minute
Geared
Shut Height S.D.A.U.
Refer To Shut Height Chart
1 ⁄4
1
1 ⁄2
1 3⁄4
2
1 ⁄2
2
3 ⁄2
3 ⁄2
8 ⁄2 x 5 ⁄2
12 x 7
14 ⁄2 x 10 ⁄2
16 x 10 ⁄2
17 ⁄4 x 13 ⁄4
22 x 16
8 ⁄2
10
12 ⁄2
12 ⁄2
17
19
Width of Opening Through Back
8 ⁄2
13 ⁄2
16
16
15 ⁄2
20
Depth of Throat from Center Line of Slide
5 ⁄4
7 ⁄2
9 ⁄2
1
10 ⁄2
13
14 3⁄4
Width Across Slide Ears
6 1⁄2
8 1⁄4
12
16
16
18
Main Bearing
1 ⁄2
2 ⁄2
3 ⁄4
4 ⁄4
5
5 1⁄2
Connecting Rod
3 7⁄8
5 3⁄8
5
5
6 1⁄2
7 1⁄2
Non-Geared
18 1⁄2
24
33
38
44
50
–
–
21 3⁄4
21 3⁄4
33
33
200
370
800
1250
1900
2150
–
–
280
280
565
565
Standard
1 9⁄16
1 9⁄16
2
2
2 1⁄2
2 1⁄2
Maximum
2
2
2 1⁄2
2 1⁄2
2 1⁄2
2 1⁄2
1
2
3
5
7 1⁄2
10
1750
1175
1175
1175
1175
1175
–
–
1750
1750
1750
1750
1
1
Rectangular
Bed
Opening
1
Round (Diameter)
Crankshaft
Diameter
Flywheel
Diameter
1
1
Geared
Die Shank
Hole Diameter
Motor Horsepower
Non-Geared
Motor
Speed (RPM)
Geared
Floor Space
at Base
1
1
1
4
3
1
1
1
4
1
1
1
1
Non-Geared
1
1
3
Geared
Flywheel
Weight (lbs.)
1
1
3
1
1
Left-to-Right
28 ⁄2
34 ⁄4
39
41
47
52
Front-to-Back
38 ⁄2
42 ⁄2
55 ⁄2
55 ⁄2
67 ⁄2
68 1⁄2
1
1
1
Shut Height Chart
1
1
1
1
Shut Height S.D.A.U.
Stroke
2
2E
3
3E
4
4E
6A
6A + 6
8 STD
8+6
10 STD
10 + 4
10 + 8
1”
–
–
–
–
13
19 ⁄4
13 ⁄2
19 ⁄2
–
–
15
19
23
1 ⁄4”
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1
3
–
1
1
3
1 ⁄4”
–
–
–
–
–
2”
7 3⁄4
12
10 3⁄4
16 1⁄4
12 ⁄2
19 ⁄4
13
19
13
19
14 ⁄2
18 ⁄2
22 1⁄2
3”
6 3⁄4
11
9 3⁄4
15 1⁄4
12
18 3⁄4
12 1⁄2
18 1⁄2
12 1⁄2
18 1⁄2
14
18
22
4”
–
–
8 3⁄4
14 1⁄4
11
17 3⁄4
11 1⁄2
17 1⁄2
12
18
13 1⁄2
17 1⁄2
21 1⁄2
5”
–
–
–
–
10
16 ⁄4
1
10 ⁄2
16 ⁄2
11 ⁄2
17 ⁄2
13
17
21
6”
–
–
–
–
9
15 ⁄4
9 ⁄2
15 ⁄2
11
17
12 ⁄2
16 ⁄2
20 1⁄2
7”
–
–
–
–
–
–
–
–
–
–
12
16
20
8”
–
–
–
–
–
–
–
–
10
16
11 ⁄2
15 ⁄2
19 1⁄2
1
1
3
3
1
1
1
1
1
–
1
1
1
–
1
1
1
Standard shut heights shown in green type with standard stroke. Values in inches unless otherwise noted. Machines may vary slightly from those shown.
www.theheimgroup.com • 6360 West 73rd Street, Chicago, IL 60638
Sales/Service: 708-496-7400 • 800-927-9393 • Fax: 708-496-7428 • Parts Fax: 708-496-0708 • Email: [email protected]
The Heim Group reserves the right to change design or detail of its products without notice. Point of operation safety guarding or devices are the sole responsibility of the employer (user) of the machine as provided in ANSI B11.1 (2001)
as published by the American National Standards Institute, Inc. and OSHA regulations. “Heim” and “Rousselle” are Reg. TM's; “Stamping Out Downtime” is a TM of The Heim Group. ©THG, 2008. All Rights Reserved.
Single Point Gap Frame • 32 to 120 Tons
Rousselle Single Point Gap Frame (Steel Fabricated)
Standard Features
• Steel Fabricated
• Combination Air Clutch and Brake
• Crankshaft Motion
• Ball Type Adjustment Screw with Bronze Seat
• Multiple V Gibbing
• Air Counterbalance System (55 Ton and Up)
• Bolster Plate
• One Shot Lubrication
• Slide Adjustment Powered by Air Wrench (Except 32 Ton Model)
• Solid State Press Control (ANSI B11.1)
• Nema 12 Enclosure Mounted on Press
• Operator Station with Dual Run, Emergency Stop and Stop on Top
•
Model G1-55
Optional Features
• Deep Throat
• Self-Monitoring Automatic Lubrication System
• Stroke Lengths other than Standard
• Additional Shut Heights
• Custom Bed Sizes
• T-Slotted Bolster
• Bolster Burnout
• Special Drilling and Machining
• Die Cushion
• Pneumatic Flywheel Brake
• Shaft Extension
• Custom Speeds
• Variable Speed Drive
• Bar Turnover with Key Selector Switch
• Pedestal for Operator Station
• Tonnage Monitor
• Console or Remote Mounted Controls
• Additional Operator Station
• Shut Height Indicator
(Except 32 Ton Models)
•
•
•
•
•
•
Palm Buttons
Supervisory Key Selector Switch for Off, Single Stroke, Inch,
or Continuous Mode
Brake Monitor
Motion Detector
Dual Air Valve
Pressure Switches for Clutch/Brake and Counterbalance
Forward/Reverse Feature
Stroke Counter
Model G1-95
(Deep Throat)
Frame
Specifications
Model
Number
OBI
B1-32
B1-55
B1-70
B1-95
B1-120
OBS
G1-32
G1-55
G1-70
G1-95
G1-120
Shut Height
STD
Capacity (Tons)
Bolster Area (Left-to-Right x Front-to-Back)
Stroke Length
Strokes Non-Geared
Per
Minute Geared
Shut
Height
S.D.A.U.
+4”
+8”
STD
+4”
+8”
STD
+4”
+8”
STD
+4”
+8”
STD
+4”
32
55
70
95
120
24 x 15
28 x 18
32 x 20
36 x 26
40 x 30
140
120
110
100
90
70
60
55
50
45
1”
11
15
14
18
22
14
18
22
15
19
23
15
19
23
2”
10 ⁄2
14 ⁄2
18 ⁄2
13 ⁄2
17 ⁄2
21 ⁄2
13 ⁄2
17 ⁄2
21 ⁄2
14 ⁄2
18 ⁄2
22 ⁄2
14 ⁄2
18 ⁄2
22 1⁄2
3”
10
14
18
13
17
21
13
17
21
14
18
22
14
18
22
4”
9 ⁄2
13 ⁄2
17 ⁄2
12 ⁄2
16 ⁄2
20 ⁄2
12 ⁄2
16 ⁄2
20 ⁄2
13 ⁄2
17 ⁄2
21 ⁄2
13 ⁄2
17 ⁄2
21 1⁄2
5”
–
–
–
12
16
20
12
16
20
13
17
21
13
17
21
6”
–
–
–
11 ⁄2
15 ⁄2
19 ⁄2
11 ⁄2
15 ⁄2
19 ⁄2
12 ⁄2
16 ⁄2
20 ⁄2
12 ⁄2
16 ⁄2
20 1⁄2
7”
–
–
–
–
–
–
–
–
–
12
16
20
12
16
20
8”
–
–
–
–
–
–
–
–
–
11 ⁄2
15 ⁄2
19 ⁄2
11 ⁄2
15 ⁄2
19 1⁄2
1
1
19
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Bolster Thickness
1 1⁄2
3
3
3
3
Slide Adjustment
2 ⁄2
4
4
4
4
Bed Opening (Left-to-Right x Front-to-Back)
14 x 7
15 x 11
15 x 11
18 x 16
18 x 16
Slide Area (Left-to-Right x Front-to-Back)
12 x 9
15 x 12 ⁄4
15 x 12 ⁄4
18 ⁄2 x 13
18 1⁄2 x 13
Width of Opening Through Back
16
18
18
20
20
Standard OBI/OBS
Depth of
Throat from
Deep Throat OBI
Center Line
of Slide
Deep Throat OBS
1
8 ⁄2
11
11
14
16
15
18
21
24
24
18
24
24
30
30
Main Bearing
3
4 ⁄2
1
4 ⁄2
6
6
Connecting Rod
4
6
6
8
8
Non-Geared
29
36
40
42
45
Geared
19
24
25 ⁄2
30 ⁄2
34
Non-Geared
430
900
1100
2270
2700
Geared
240
640
720
800
1000
3
5
17 ⁄5
10
10
Non-Geared
1775
1175
1175
1175
1175
Geared
1750
1750
1750
1750
1750
Floor to Top of Bed
32
32
32
35 ⁄2
35 1⁄2
Die Shank Hole Diameter
2
2
2
2 1⁄2
2 1⁄2
Crankshaft
Diameter
Flywheel
Diameter
Flywheel
Weight (lbs.)
1
Motor Horsepower
Motor Speed
(RPM)
Overall Height
Floor Space
at Base
(Left-toRight x
Frontto-Back)
+8”
93
97
1
1
1
101
101
105
1
1
1
1
109
101
105
1
109
117
121
125
117
121
35 x 51
51 x 60
51 x 60
56 x 85
56 x 85
37 x 36
39 x 43
39 x 48
40 x 65
40 x 71
37 x 59
37 x 76
37 x 76
50 x 100
50 x 100
37 x 49
39 x 61
39 x 73
42 x 75
42 x 95
125
Specifications vary by frame only where indicated. Values in inches unless otherwise noted. Standard shut heights shown in green type with
standard stroke. Machines may vary slightly from those shown.
www.theheimgroup.com • 6360 West 73rd Street, Chicago, IL 60638
Sales/Service: 708-496-7400 • 800-927-9393 • Fax: 708-496-7428 • Parts Fax: 708-496-0708 • Email: [email protected]
The Heim Group reserves the right to change design or detail of its products without notice. Point of operation safety guarding or devices are the sole responsibility of the employer (user) of the machine as provided in ANSI B11.1 (2001)
as published by the American National Standards Institute, Inc. and OSHA regulations. “Heim” and “Rousselle” are Reg. TM's; “Stamping Out Downtime” is a TM of The Heim Group. ©THG, 2008. All Rights Reserved.
Single Point Gap Frame • 150 to 300 Tons
Rousselle Single Point Gap Frame
Standard Features
• Steel Fabricated
• Combination Air Clutch and Brake
• Crankshaft Motion
• Ball Type Adjustment Screw with Bronze Seat
• Adjustable 8 Point Gibbing
• Air Counterbalance System
• Bolster Plate
• Self-Monitoring Automatic Lubrication System
• Powered Slide Adjustment with Digital Position
•
•
•
•
•
•
•
•
•
•
Indicator
Solid State Press Control (ANSI B11.1)
Nema 12 Enclosure Mounted on Press
Operator Station with Dual Run, Emergency Stop
and Stop on Top Palm Buttons
Supervisory Key Selector Switch for Off, Single Stroke,
Inch or Continuous Mode
Brake Monitor
Motion Detector
Dual Air Valve
Pressure Switches for Clutch/Brake and
Counterbalance
Forward/Reverse Feature
Stroke Counter
Optional Features
• Hydraulic Overload System
• Stroke Lengths other than Standard
• Additional Shut Heights
• Custom Bed Sizes
• T-Slotted Bolster
• Bolster Burnout
• Special Drilling and Machining
• Die Cushions
• Pneumatic Flywheel Brake
• Shaft Extension
• Custom Speeds
• Variable Speed Drive
• Pedestal for Operator Station
• Tonnage Monitor
• Console or Remote Mounted Controls
• Additional Operator Station
Model G1-200
Model Number
Frame
Specifications
OBI
B1-150
B1-200
—
—
OBS
G1-150
G1-200
G1-250
G1-300
Shut Height
STD
+4”
Capacity at ⁄4”(Tons) B.D.C.
+4”
+12”
STD
+6”
+12”
STD
+6”
50 x 32
50 x 32
54 x 32
60 x 32
Non-Geared
80
70
—
—
Geared
40
35
40
35
+ 12”
2”
20
24
28
32
20
24
28
32
20
26
32
20
26
32
4”
19
23
27
31
19
23
27
31
19
25
31
19
25
31
6”
18
22
26
30
18
22
26
30
18
24
30
18
24
30
8”
17
21
25
29
17
21
25
29
17
23
29
17
23
29
10”
13
17
21
25
13
17
21
25
13
19
25
13
19
25
12”
12
16
20
24
12
16
20
24
12
18
24
12
18
24
14”
–
–
–
–
–
–
–
–
11
17
23
11
17
23
4
Slide Adjustment
4
4
4
6
6
6
6
22 x 20
22 x 20
24 x 20
24 x 20
31 1⁄2 x 23 1⁄2
31 1⁄2 x 23 1⁄2
36 x 23 1⁄2
36 x 23 1⁄2
24
24
28 1⁄2
28 1⁄2
OBI
16 1⁄2
16 1⁄2
—
—
OBS
16 1⁄2
16 1⁄2
16 1⁄2
16 1⁄2
Main Bearing
7 1⁄2
7 1⁄2
9 1⁄4
9 1⁄4
Connecting Rod
10
10
12
12
48 1⁄2
54 1⁄2
—
—
36
40
36
40
Non-Geared
2400
2890
—
—
Geared
850
1050
1700
2100
15
20
25
30
Non-Geared
1175
1175
—
—
Geared
1750
1750
1750
1750
OBI
41 ⁄2
41 ⁄2
—
—
OBS
36 ⁄2
36 ⁄2
36 ⁄2
36 1⁄2
Bed Opening (Left-to-Right x Front-to-Back)
Slide Area (Left-to-Right x Front-to-Back)
Width of Opening Through Back
Frame
+8”
300
Bolster Thickness
Depth of Throat from
Center Line of Slide
STD
250
Stroke Length
Shut Height
S.D.A.U.
+12”
200
Bed and Bolster Area (Left-to-Right x Front-to-Back)
Strokes
Per Minute
+ 8”
150
1
Crankshaft Diameter
Non-Geared
Flywheel Diameter
Geared
Flywheel Weight (lbs.)
Motor Horsepower
Motor Speed (RPM)
1
1
Floor to Top of Bed
Floor Space at Base
(Left-to-Right x
Front-to-Back)
Frame
Overall Height with Standard Shut Height
1
177
181
1
185
189
177
181
1
185
189
179
184
190
179
184
50 x 108
50 x 108
—
—
50 x 73 ⁄2
50 x 73 ⁄2
50 x 84
50 x 84
1
1
190
Values in inches unless otherwise noted. Machines may vary slightly from those shown.
Standard shut heights shown in green type with standard stroke.
www.theheimgroup.com • 6360 West 73rd Street, Chicago, IL 60638
Sales/Service: 708-496-7400 • 800-927-9393 • Fax: 708-496-7428 • Parts Fax: 708-496-0708 • Email: [email protected]
The Heim Group reserves the right to change design or detail of its products without notice. Point of operation safety guarding or devices are the sole responsibility of the employer (user) of the machine as provided in ANSI B11.1 (2001)
as published by the American National Standards Institute, Inc. and OSHA regulations. “Heim” and “Rousselle” are Reg. TM's; “Stamping Out Downtime” is a TM of The Heim Group. ©THG, 2008. All Rights Reserved.
Two Point Gap Frame • 40 and 60 Tons
Rousselle Two Point Gap Frame
Standard Features
• Steel Fabricated
• Air Clutch
• Shoe Brake
• Wrist Pin Connection
• V Gibbing
• Air Counterbalance System
• Eccentric Shaft Motion
• Bolster Plate
• One Shot Lubrication
• Manual Slide Adjustment
• Solid State Press Control (ANSI B11.1)
• Nema 12 Enclosure Mounted on Press
• Operator Station with Dual Run, Emergency Stop
•
•
•
•
•
•
•
and Stop on Top Palm Buttons
Supervisory Key Selector Switch for Off, Single Stroke,
Inch or Continuous Mode
Brake Monitor
Motion Detector
Dual Air Valve
Pressure Switches for Clutch/Brake and Counterbalance
Forward/Reverse Feature
Stroke Counter
Optional Features
• Self-Monitoring Automatic Lubrication System
• Powered Slide Adjustment with Digital Position Indicator
• Stroke Lengths other than Standard
• Additional Shut Heights
• Custom Bed Sizes
• T-Slotted Bolster
• Bolster Burnout
• Special Drilling and Machining
• Custom Speeds
• Variable Speed Drive
• Remote Mounted Controls
• Tonnage Monitor
• Additional Operator Station
• Adjustable Bed
Model 4B48
Specifications
Model Number
4B48
4B60
4B76
6B48
6B60
6B76
40
40
40
60
60
60
48 x 16
60 x 18
76 x 18
48 x 18
60 x 18
76 x 18
Non-Geared
105
105
105
110
110
110
Geared
45
50
50
50
50
50
1”
12 ⁄2
13
2”
12
12 ⁄2
12 ⁄2
12 ⁄2
12 ⁄2
12 1⁄2
3”
11 3⁄4
11 1⁄2
11 1⁄2
11 1⁄2
11 1⁄2
11 1⁄2
4”
10 3⁄4
10 1⁄2
10 1⁄2
10 1⁄2
10 1⁄2
10 1⁄2
5”
9 3⁄4
9 1⁄2
9 1⁄2
9 1⁄2
9 1⁄2
9 1⁄2
Capacity (Tons) B.D.C.
Area of Bed (Left-to-Right x Front-to-Back)
Stroke Length
Strokes Per Minute
Shut Height S.D.A.U.
Slide Adjustment
1
13
1
13
1
13
1
13
1
3
3
3
3
3
3
Bed Opening
37 x 10
48 ⁄2 x 15
64 ⁄2 x 15
36 ⁄2 x 15
48 ⁄2 x 15
64 ⁄2 x 15
Slide Area (Left-to-Right x Front-to-Back)
36 x 14
49 ⁄2 x 16
65 ⁄2 x 16
37 ⁄2 x 16
49 ⁄2 x 16
65 1⁄2 x 16
Width of Opening Through Back
37
52 1⁄2
68 1⁄2
40 1⁄2
52 1⁄2
68 1⁄2
Depth of Throat from Centerline of Slide
9
10
10
10
10
10
Main Bearing
3 ⁄4
4 ⁄4
4 ⁄4
4 ⁄4
4 ⁄4
4 1⁄4
Connecting Rod
6 1⁄4
6 1⁄4
6 1⁄4
7 1⁄4
7 1⁄4
7 1⁄4
Non-Geared
33
33
33
38
38
38
Geared
22
22
22
22
22
22
Non-Geared
800
800
800
1050
1050
1050
Geared
236
236
236
236
236
236
3
3
3
5
5
5
Non-Geared
1175
1175
1175
1175
1175
1175
Geared
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Crankshaft Diameter
Flywheel Diameter
Flywheel Weight (lbs.)
Motor Horsepower
Motor Speed (RPM)
1750
1750
1750
1750
1750
1750
Floor to Top of Bed
30 3⁄4
40
40
40
40
40
Overall Height with Standard Stroke
113
125
125
125
125
125
Left-to-Right
56 3⁄4
72
88
60
72
88
Front-to-Back
47
76
76
76
76
76
Floor Space at Base
Standard shut heights shown in green type with standard stroke. Values in inches unless otherwise noted. Machines may vary slightly from those shown.
Consult factory for specifications for adjustable bed models.
www.theheimgroup.com • 6360 West 73rd Street, Chicago, IL 60638
Sales/Service: 708-496-7400 • 800-927-9393 • Fax: 708-496-7428 • Parts Fax: 708-496-0708 • Email: [email protected]
The Heim Group reserves the right to change design or detail of its products without notice. Point of operation safety guarding or devices are the sole responsibility of the employer (user) of the machine as provided in ANSI B11.1 (2001)
as published by the American National Standards Institute, Inc. and OSHA regulations. “Heim” and “Rousselle” are Reg. TM's; “Stamping Out Downtime” is a TM of The Heim Group. ©THG, 2008. All Rights Reserved.
Two Point Gap Frame • 80 and 100 Tons
Rousselle Two Point Gap Frame
Standard Features
• Steel Fabricated
• Air Clutch
• Disc Brake
• Wrist Pin Connection
• 45 Degree Gib
• Air Counterbalance System
• Crankshaft Motion
• Bolster Plate
• One Shot Lubrication
• Manual Slide Adjustment
• Solid State Press Control (ANSI B11.1)
• Nema 12 Enclosure Mounted on Press
• Operator Station with Dual Run, Emergency Stop
•
•
•
•
•
•
•
and Stop on Top Palm Buttons
Supervisory Key Selector Switch for Off,
Single Stroke, Inch or Continuous Mode
Brake Monitor
Motion Detector
Dual Air Valve
Pressure Switches for Clutch/Brake and Counterbalance
Forward/Reverse Feature
Stroke Counter
Optional Features
• Self-Monitoring Automatic Lubrication System
• Powered Slide Adjustment with Digital Position Indicator
• Stroke Lengths other than Standard
• Additional Shut Heights
• Custom Bed Sizes
• T-Slotted Bolster
• Bolster Burnout
• Special Drilling and Machining
• Custom Speeds
• Variable Speed Drive
• Remote Mounted Controls
• Tonnage Monitor
• Additional Operator Station
• Adjustable Bed
Model 10K48
Specifications
8K48
8K60
8K80
8K100
10K48
10K60
10K80
10K100
OBI
8B48
8B60
8B80
8B100
10B48
10B60
10B80
10B100
80
80
80
80
100
100
100
100
Area of Bed (Left-to-Right x Front-to-Back)
48 x 22
60 x 22
80 x 22
100 x 22
48 x 22
60 x 22
80 x 22
100 x 22
Bed Opening
40 x 18
52 x 18
72 x 18
92 x 18
40 x 18
52 x 18
72 x 18
92 x 18
Width of Opening Through Back
42
54
74
94
42
54
75
94
Depth of Throat
12
12
12
12
12
12
12
12
Frame
OBS
Model Number
Capacity (Tons) B.D.C.
Shut Height S.D.A.U.
Refer To Shut Height Chart
Slide Area
40 x 18
52 x 18
72 x 18
92 x 18
40 x 18
52 x 18
72 x 18
92 x 18
4
4
4
4
4
4
4
4
Slide Adjustment
33 ⁄2
33 ⁄2
33 ⁄2
33 ⁄2
33 ⁄2
33 ⁄2
33 ⁄2
33 1⁄2
B Series (OBI)
35
35
35
35
35
35
35
35
Left-to-Right
57
68
89
109
57
69
89
109
Front-to-Back
51
51
51
51
51
51
51
51
Left-to-Right
66
78
98
118
66
78
98
118
Front-to-Back
78
78
78
78
78
78
78
78
135
135
135
135
135
135
135
135
With 1”, 2”, 3”, 4” Stroke
65
65
65
65
65
65
65
65
With 5”, 6”, 7”, 8” Stroke
50
50
50
50
50
50
50
50
Motor Horsepower
7 ⁄2
7 ⁄2
7 ⁄2
7 ⁄2
10
10
10
10
Motor Speed (RPM)
1750
1750
1750
1750
1750
1750
1750
1750
Frame
K Series (OBS)
Floor to Top of Bed
1
1
1
1
1
1
1
Floor Space
at Base
Frame
K Series
B Series
Overall Height with Standard Shut Height
Strokes Per Minute
1
1
1
1
K & B Shut Height Chart
Shut Height S.D.A.U.
Strokes
Standard
Additional
4”
Additional
8”
1”
14 1⁄2
18 1⁄2
22 1⁄2
2”
14
18
22
3”
13 ⁄2
17 ⁄2
21 1⁄2
4”
13
17
21
5”
12 1⁄2
16 1⁄2
20 1⁄2
6”
11
15
19
7”
10 1⁄2
14 1⁄2
18 1⁄2
8”
10
14
18
1
1
Standard shut heights shown in green type with standard
stroke. Values in inches unless otherwise noted. Machines
may vary slightly from those shown.
Sales/Service: 708-496-7400 •
www.theheimgroup.com • 6360 West 73rd Street, Chicago, IL 60638
800-927-9393 • Fax: 708-496-7428 • Parts Fax: 708-496-0708 • Email: [email protected]
The Heim Group reserves the right to change design or detail of its products without notice. Point of operation safety guarding or devices are the sole responsibility of the employer (user) of the machine as provided in ANSI B11.1 (2001)
as published by the American National Standards Institute, Inc. and OSHA regulations. “Heim” and “Rousselle” are Reg. TM's; “Stamping Out Downtime” and is a TM of The Heim Group. ©THG, 2008. All Rights Reserved.
Two Point Gap Frame • 150 to 300 Tons
Rousselle Two Point Gap Frame
Standard Features
• Steel Fabricated
• Combination Air Clutch and Brake
• Eccentric Geared Drive
• Ball Type Adjustment Screw with Bronze Seat
• Adjustable 6 Point Gibbing
• Air Counterbalance System
• Bolster Plate
• Self-Monitoring Automatic Lubrication System
• Powered Slide Adjustment with Digital Position Indicator
• Solid State Press Control (ANSI B11.1)
• Nema 12 Enclosure Mounted on Press
• Operator Station with Dual Run, Emergency Stop
•
•
•
•
•
•
•
and Stop on Top Palm Buttons
Supervisory Key Selector Switch for Off,
Single Stroke, Inch or Continuous Mode
Brake Monitor
Motion Detector
Dual Air Valve
Pressure Switches for Clutch/Brake and
Counterbalance
Forward/Reverse Feature
Stroke Counter
Optional Features
• Hydraulic Overload System
• Stroke Lengths other than Standard
• Additional Shut Heights
• Custom Bed Sizes
• T-Slotted Bolster
• Bolster Burnout
• Special Drilling and Machining
• Die Cushions
• Pneumatic Flywheel Brake
• Custom Speeds
• Variable Speed Drive
• Pedestal for Operator Station
• Tonnage Monitor
• Console Mounted Controls
• Additional Operator Station
Model G2-150
Specifications
Model Number
G2-150
G2-200
G2-250
G2-300
150
200
250
300
100 x 42
100 x 42
21
19
100 x 36
100 x 36
6
6
1/4” Rated Capacity Above B.D.C.
Bed Area (Left-to-Right x Front-to-Back)
80 x 36
100 x 36
Strokes Per Minute
80 x 36
25
100 x 36
22
Shut Height S.D.A.U.
Refer to Shut Height Chart
Slide Area
80 x 32
100 x 32
Slide Adjustment
80 x 32
6
Bed Opening
Width of Opening Through Back
100 x 32
6
76 1⁄2 x 18
96 1⁄2 x 18
76 1⁄2 x 18
96 1⁄2 x 18
96 1⁄2 x 20
96 1⁄2 x 20
86
106
86
106
106
106
Depth of Throat from Center Line of Slide
16
16
16
16
Motor Horsepower
15
20
25
30
Motor Speed (RPM)
1750
1750
1750
1750
Floor To Top of Bed
34 ⁄2
34 ⁄2
34 ⁄2
34 1⁄2
1
Distance Between Gibs
1
1
82 1⁄4
102 1⁄4
82 1⁄4
102 1⁄4
102 1⁄4
102 1⁄4
Left-to-Right
110
130
110
130
130
130
Front-to-Back
87 1⁄2
87 1⁄2
87 1⁄2
87 1⁄2
92 1⁄2
92 1⁄2
155
155
Floor Space at Base
Overall Height with Standard Shut Height
143
143
Shut Height Chart
Shut Height S.D.A.U.
Stroke Length
G2-150 and G2-200
G2-250 and G2-300
2”
17
21
25
29
–
–
–
–
3”
16 1⁄2
20 1⁄2
24 1⁄2
28 1⁄2
–
–
–
–
4”
16
20
24
28
14
18
22
26
6”
13
17
21
25
13
17
21
25
7”
12 ⁄2
16 ⁄2
20 ⁄2
24 ⁄2
–
–
–
–
8”
12
16
20
24
11
15
19
23
10”
–
–
–
–
9
13
17
21
12”
–
–
–
–
7
11
15
19
1
1
1
1
Values in inches unless otherwise noted. Machines may vary slightly from those shown. Standard shut heights shown in green type with standard stroke.
www.theheimgroup.com • 6360 West 73rd Street, Chicago, IL 60638
Sales/Service: 708-496-7400 • 800-927-9393 • Fax: 708-496-7428 • Parts Fax: 708-496-0708 • Email: [email protected]
The Heim Group reserves the right to change design or detail of its products without notice. Point of operation safety guarding or devices are the sole responsibility of the employer (user) of the machine as provided in ANSI B11.1 (2001)
as published by the American National Standards Institute, Inc. and OSHA regulations. “Heim” and “Rousselle” are Reg. TM's; “Stamping Out Downtime” is a TM of The Heim Group. ©THG, 2008. All Rights Reserved.
Two Point Straight Side • 40 and 60 Tons
Rousselle Two Point Straight Side
Standard Features
• Steel Fabricated
• Air Clutch
• Shoe Brake
• Wrist Pin Connection
• V Gibbing
• Air Counterbalance System
• Eccentric Shaft Motion
• Bolster Plate
• One Shot Lubrication
• Manual Slide Adjustment
• Solid State Press Control (ANSI B11.1)
• Nema 12 Enclosure Mounted on Press
• Operator Station with Dual Run, Emergency Stop
•
•
•
•
•
•
•
and Stop on Top Palm Buttons
Supervisory Key Selector Switch for Off, Single Stroke,
Inch or Continuous Mode
Brake Monitor
Motion Detector
Dual Air Valve
Pressure Switches for Clutch/Brake and
Counterbalance
Forward/Reverse Feature
Stroke Counter
Optional Features
• Self-Monitoring Automatic Lubrication System
• Powered Slide Adjustment with Digital Position Indicator
• Stroke Lengths other than Standard
• Additional Shut Heights
• Custom Bed Sizes
• T-Slotted Bolster
• Bolster Burnout
• Special Drilling and Machining
• Custom Speeds
• Variable Speed Drive
• Remote Mounted Controls
• Tonnage Monitor
• Additional Operator Station
Model 6SS72
Specifications
Model Number
4SS44
4SS56
4SS72
6SS44
6SS56
6SS72
40
40
40
60
60
60
44 x 22
56 x 22
72 x 22
44 x 22
56 x 22
72 x 22
Non-Geared
105
105
105
110
110
110
Geared
45
45
45
50
50
50
Capacity (Tons) Near B.D.C.
Bed Area (Left-to-Right x Front-to-Back)
Strokes
Per Minute
Shut Height S.D.A.U.
Refer To Shut Height Chart
Slide Area (Left-to-Right x Front-to-Back)
40 x 14
52 x 14
68 x 14
40 x 14
52 x 14
68 x 14
3
3
3
3
3
3
36 x 14
48 x 14
64 x 14
36 x 14
48 x 14
64 x 14
44
56
72
44
56
72
Slide Adjustment
Bed Opening (Left-to-Right x Front-to-Back)
Left-To-Right
Opening Between
Uprights
Front-To-Back
12
12
12
12
12
12
Main Bearing
3 1⁄4
3 1⁄4
3 1⁄4
4 1⁄4
4 1⁄4
4 1⁄4
Connecting Rod
6 1⁄4
6 1⁄4
6 1⁄4
7 1⁄4
7 1⁄4
7 1⁄4
Non-Geared
33
33
33
38
38
38
Geared
22
22
22
22
22
22
Non-Geared
800
800
800
1050
1050
1050
Geared
300
300
300
300
300
300
3
3
3
5
5
5
Non-Geared
1175
1175
1175
1175
1175
1175
Geared
1750
1750
1750
1750
1750
1750
Floor to Top of Bed
33 1⁄4
33 1⁄4
33 1⁄4
33 1⁄4
33 1⁄4
33 1⁄4
Overall Height with Standard Shut Height
114
114
114
114
114
114
59
71
87
59
71
87
33 ⁄2
33 ⁄2
33 ⁄2
33 ⁄2
33 ⁄2
33 1⁄2
Crankshaft
Diameter
Flywheel
Diameter
Flywheel
Weight (lbs.)
Motor Horsepower
Motor Speed
(RPM)
Left-To-Right
Floor Space
at Base
4SS Shut Height Chart
Front-To-Back
1
1
Stroke
1
1
1
Shut Height S.D.A.U.
1”
8 ⁄4
10 ⁄4
12 ⁄4
14 ⁄4
16 ⁄4
18 1⁄4
20 1⁄4
22 1⁄4
24 1⁄4
26 1⁄4
28 1⁄4
2”
7 3 ⁄4
9 3⁄4
11 3⁄4
13 3⁄4
15 3⁄4
17 3⁄4
19 3⁄4
21 3⁄4
23 3⁄4
25 3⁄4
27 3⁄4
3”
7 1⁄2
9 1⁄2
11 1⁄2
13 1⁄2
15 1⁄2
17 1⁄2
19 1⁄2
21 1⁄2
23 1⁄2
25 1⁄2
27 1⁄2
4”
6 ⁄2
8 ⁄2
10 ⁄2
12 ⁄2
14 ⁄2
16 ⁄2
18 ⁄2
20 ⁄2
22 ⁄2
24 ⁄2
26 1⁄2
15 1⁄2
17 1⁄2
19 1⁄2
21 1⁄2
23 1⁄2
25 1⁄2
1
1
1
1
1
1
6SS Shut Height Chart
5”
1
1
1
1
1
1
1
1
1
5 1⁄2
7 1⁄2
9 1⁄2
11 1⁄2
13 1⁄2
1”
8 1⁄4
10 1⁄4
12 1⁄4
14 1⁄4
16 1⁄4
18 1⁄4
20 1⁄4
22 1⁄4
24 1⁄4
26 1⁄4
28 1⁄4
2”
8
10
12
14
16
18
20
22
24
26
28
3”
7
9
11
13
15
17
19
21
23
25
27
4”
6
8
10
12
14
16
18
20
22
24
26
5”
5
7
9
11
13
15
17
19
21
23
25
Stroke
Shut Height S.D.A.U.
Standard shut heights shown in green type with standard stroke. Values in inches unless otherwise noted. Machines may vary slightly from those shown.
www.theheimgroup.com • 6360 West 73rd Street, Chicago, IL 60638
Sales/Service: 708-496-7400 • 800-927-9393 • Fax: 708-496-7428 • Parts Fax: 708-496-0708 • Email: [email protected]
The Heim Group reserves the right to change design or detail of its products without notice. Point of operation safety guarding or devices are the sole responsibility of the employer (user) of the machine as provided in ANSI B11.1 (2001)
as published by the American National Standards Institute, Inc. and OSHA regulations. “Heim” and “Rousselle” are Reg. TM's; “Stamping Out Downtime” is a TM of The Heim Group. ©THG, 2008. All Rights Reserved.
Two Point Straight Side • 80 to 100 Tons
Rousselle Two Point Straight Side
Standard Features
• Steel Fabricated
• Air Clutch
• Disc Brake
• Wrist Pin Connection
• 45 Degree Gib
• Air Counterbalance System
• Crankshaft Motion
• Bolster Plate
• One Shot Lubrication
• Manual Slide Adjustment
• Solid State Press Control (ANSI B11.1)
• Nema 12 Enclosure Mounted on Press
• Operator Station with Dual Run, Emergency
•
•
•
•
•
•
•
Stop and Stop on Top Palm Buttons
Supervisory Key Selector Switch for Off,
Single Stroke, Inch or Continuous Mode
Brake Monitor
Motion Detector
Dual Air Valve
Pressure Switches for Clutch/Brake and
Counterbalance
Forward/Reverse Feature
Stroke Counter
Optional Features
• Self-Monitoring Automatic Lubrication System
• Powered Slide Adjustment with Digital Position Indicator
• Stroke Lengths other than Standard
• Additional Shut Heights
• Custom Bed Sizes
• T-Slotted Bolster
• Bolster Burnout
• Special Drilling and Machining
• Custom Speeds
• Variable Speed Drive
• Remote Mounted Controls
• Tonnage Monitor
• Additional Operator Station
Model 8SS100
Specifications
Model Number
8SS40
8SS60
8SS80
8SS100
10SS40
10SS60
10SS80
10SS100
80
80
80
80
100
100
100
100
40 x 30
60 x 30
80 x 30
100 x 30
40 x 30
60 x 30
80 x 30
100 x 30
With 1”, 2”, 3”, 4” Stroke
75
75
75
75
65
65
65
65
With 5”, 6”, 7”, 8” Stroke
55
55
55
55
50
50
50
50
Capacity (Tons) Near B.D.C.
Bed Area (Left-to-Right x Front-to-Back)
Strokes
Per Minute
Shut Height S.D.A.U.
Refer To Shut Height Chart
Slide Area (Left-to-Right x Front-to-Back)
39 x 20
59 x 20
79 x 20
99 x 20
39 x 20
59 x 20
79 x 20
99 x 20
4
4
4
4
4
4
4
4
28 x 18
48 x 18
68 x 18
88 x 18
28 x 18
48 x 18
68 x 18
88 x 18
Left-to-Right
40
60
80
100
40
60
80
100
Front-to-Back
14
14
14
14
14
14
14
14
Main Bearing
3 ⁄4
3 ⁄4
3 ⁄4
3 ⁄4
4 ⁄4
4 ⁄4
4 ⁄4
4 1⁄4
Connecting Rod
5
5
5
5
5
5
5
5
With 1”, 2”, 3”, 4” Stroke
24
24
24
24
24
24
24
24
With 5”, 6”, 7”, 8” Stroke
33
33
33
33
33
33
33
33
With 1”, 2”, 3”, 4” Stroke
320
320
320
320
320
320
320
320
With 5”, 6”, 7”, 8” Stroke
490
490
490
490
490
490
490
490
Motor Horsepower
7 1⁄2
7 1⁄2
7 1⁄2
7 1⁄2
10
10
10
10
Motor Speed (RPM)
1750
1750
1750
1750
1750
1750
1750
1750
Floor to Top of Bed
30
30
30
30
30
30
30
30
Overall Height with Standard Shut Height
125
125
125
125
125
125
125
125
Left-to-Right
56
76
96
116
56
76
96
116
Front-to-Back
38 1⁄2
38 1⁄2
38 1⁄2
38 1⁄2
38 1⁄2
38 1⁄2
38 1⁄2
38 1⁄2
Slide Adjustment
Bed Opening (Left-to-Right x Front-to-Back)
Opening Between
Uprights
Crankshaft
Diameter
Flywheel
Diameter
Flywheel
Weight (lbs.)
Floor Space
at Base
1
Shut Height Chart
1
Stroke
1
1
1
1
1
Shut Height S.D.A.U.
1”
10
12
14
16
18
20
22
24
26
28
2”
9 ⁄2
11 ⁄2
13 ⁄2
15 ⁄2
17 ⁄2
19 ⁄2
21 ⁄2
23 ⁄2
25 ⁄2
27 1⁄2
3”
9
11
13
15
17
19
21
23
25
27
4”
8 ⁄2
10 ⁄2
12 ⁄2
14 ⁄2
16 ⁄2
18 ⁄2
20 ⁄2
22 ⁄2
24 ⁄2
26 1⁄2
5”
8
10
12
14
16
18
20
22
24
26
6”
7 ⁄2
9 ⁄2
11 ⁄2
13 ⁄2
15 ⁄2
17 ⁄2
19 ⁄2
21 ⁄2
23 ⁄2
25 1⁄2
7”
7
9
11
13
15
17
19
21
23
25
8”
6 ⁄2
8 ⁄2
10 ⁄2
12 ⁄2
14 ⁄2
16 ⁄2
18 ⁄2
20 ⁄2
22 ⁄2
24 1⁄2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Standard shut heights shown in green type with standard stroke. Values in inches unless otherwise noted. Machines may vary slightly from those shown.
www.theheimgroup.com • 6360 West 73rd Street, Chicago, IL 60638
Sales/Service: 708-496-7400 • 800-927-9393 • Fax: 708-496-7428 • Parts Fax: 708-496-0708 • Email: [email protected]
The Heim Group reserves the right to change design or detail of its products without notice. Point of operation safety guarding or devices are the sole responsibility of the employer (user) of the machine as provided in ANSI B11.1 (2001)
as published by the American National Standards Institute, Inc. and OSHA regulations. “Heim” and “Rousselle” are Reg. TM's; “Stamping Out Downtime” is a TM of The Heim Group. ©THG, 2008. All Rights Reserved.
Two Point Straight Side • 150 to 400 Tons
Rousselle Two Point Straight Side
Standard Features
• All Welded Steel Frame with Double-Wall Bed Construction
• Pre-Stressed Tie Rods Ensure Minimum Deflection
• Drive Capacity Rated ⁄ " Above Bottom of Stroke
• Eccentric Geared Motion
• Adjustable 8 Point Gibbing
• Air Counterbalance System
• Combination Air Clutch and Brake
• Solid State Press Control (ANSI B11.1)
• Above Floor Construction
• Bolster Plate
• Powered Slide Adjustment with Digital Position
1
•
•
•
•
•
•
•
•
•
4
Indicator
Self-Monitoring Automatic Lubrication System
Ball Type Adjustment Screw with Bronze Seat
Operator Station with Dual Run, Emergency
Stop and Stop on Top Palm Buttons
Supervisory Key Selector Switch for Off,
Single Stroke, Inch or Continuous Mode
Brake Monitor
Motion Detector
Dual Air Valve
Forward/Reverse Feature
Stroke Counter
Optional Features
• Stroke Lengths other than Standard
• Shut Heights other than Standard
• T-Slotted Slide and Bolster Plate
• Pedestal for Operator Station
• Variable Speed Drive
• Custom Bed Sizes
• Hydraulic Overload
• Die Cushions
• Flywheel Brake
• Tonnage Monitor
• Console Mounted Controls
• Custom Speeds
Model S2-250
Specifications
Model Number
S2-150
S2-200
S2-250
S2-300
S2-400
150
200
250
300
400
Capacity at 1⁄4” Up with
Standard Stroke (Tons)
Bed and Bolster Area (Left-to-Right x Front-to-Back)
78 x 42
Uprights (Left-to-Right x Front-to-Back)
100 x 42
78 x 42
8x8
100 x 42
100 x 48
8x8
120 x 48
100 x 48
10 x 10
120 x 48
100 x 48
10 x 10
120 x 48
10 x 10
Bed Opening (Left-to-Right x Front-to-Back)
72 x 24
94 x 24
72 x 24
94 x 24
94 x 27
112 x 27
92 x 27
112 x 27
92 x 26
112 x 26
Slide Area (Left-to-Right x Front-to-Back)
78 x 30
102 x 30
78 x 30
102 x 30
100 x 36
120 1⁄2 x 36
100 x 36
120 1⁄2 x 36
100 x 36
120 1⁄2 x 36
Standard Stroke / Max
3/8
3/8
4/12
4/12
4/12
Shut Height with Standard
Stroke S.D.A.U.
12
12
16
16
16
Single Gear
25 - 60
25 - 60
–
–
–
Double Gear
–
–
21 - 37
19 - 34
18 - 32
6
6
6
6
6
Strokes Per Minute
Slide Adjustment
Distance Between Uprights (Left-to-Right)
78
Floor to Top of Bed
Upright Openings (Front-to-Back)
102 1⁄2
122 1⁄2
102 1⁄2
122 1⁄2
102 1⁄2
122 1⁄2
34
40
40
40
22 ⁄2
22 ⁄2
22 ⁄2
26 ⁄4
26 3⁄4
15
20
25
30
40
1
119 x 63
95 x 63
140
21,000
102
34
95 x 63
Overall Height with
Standard Stroke and Shut Height
Approximate Weight (lbs.)
78
1
Main Motor Horsepower
Floor Space (Left-to-Right x Front-to-Back)
102
1
119 x 63
119 x 75
140
24,000
23,000
3
139 x 75
119 x 75
162
26,000
33,000
139 x 75
119 x 75
162
36,000
37,000
139 x 75
163
40,000
44,000
48,000
Values in inches unless otherwise noted. Machines may vary slightly from those shown.
1 Crown
2 Columns
3 Slide with T-Slots
4 8 Point Gibbing
5 Connecting Rod
6 Ball Type Adjusting Screw
7 Bolster with T-Slots
8 Above Floor Bed Construction
9 Counterbalance Cylinders
10 Pre-Stressed Tie Rods
11 Main Motor
12 Flywheel
13 Combination Clutch/Brake
14 Helical Drive Pinion
15 Helical Intermediate Gear
16 Eccentric Gear
FRONT VIEW
SIDE VIEW
www.theheimgroup.com • 6360 West 73rd Street, Chicago, IL 60638
Sales/Service: 708-496-7400 • 800-927-9393 • Fax: 708-496-7428 • Parts Fax: 708-496-0708 • Email: [email protected]
The Heim Group reserves the right to change design or detail of its products without notice. Point of operation safety guarding or devices are the sole responsibility of the employer (user) of the machine as provided in ANSI B11.1 (2001)
as published by the American National Standards Institute, Inc. and OSHA regulations. “Heim” and “Rousselle” are Reg. TM's; “Stamping Out Downtime” is a TM of The Heim Group. ©THG, 2008. All Rights Reserved.
MECHANICAL
PRESS BRAKES
35- to 200- Ton Capacity
Standard and Permanently Flanged Models
HEIM MECHANICAL PRESS BRAKES...
The economical choice for a wide variety of
metal bending and stamping operations.
With 46 standard models to choose from, there
is a Heim mechanical press brake to fit your specific
production requirements. Heim press brakes are built
for accuracy, dependability and durability for years of
profitable use. Available in capacities from 35- to 200ton, these versatile machines are equipped with the
following quality features.
Heim mechanical press brakes are available in two
types: Standard Press Brake and Permanently
Flanged models.
Standard Features
n Solid state press brake control
n HI PROTM low-inertia combination clutch and brake
n Double-wall construction
n 100% ram guidance through entire stroke length
n Intermediate helical gearing
n Powered ram adjustment and indicator
(45-ton models and larger)
Optional Features
n Automatic lubrication
n Manual, front-operated back gauge
n Powered, front-operated back gauge
n Air counterbalances
n Machining bed and ram for removable angles
51/2” and 71/2” removable angles
n Ram and bed exetensions
n Powered ram adjustment (35-ton model)
n Optional stroke lengths
(see specifications on back cover)
100-Ton, 6 Foot permanently flanged model.
Controls
n Meets and exceeds OSHA 1910.212 ANSI B11.3 and
B11.19 requirements
n Provides two-hand control safeguarding device
n Interface provided for light curtain(s)
n Time-based brake monitor
Modes Of Opeation
SSC-1500 Custome Control Box
(Operators Located on Door Front)
n
n
n
n
n
n
Off
Two-hand inch (timed or regular)
Two-hand single stroke
Foot single stroke
Sequence stop (hand/hand-hand/foot-foot/foot)
High/low automatic speed change (for two Speed only)
HI PROTM Low Inertia Combination
Clutch and Brake
Withstanding the stress of frequent starts and stops,
this low inertia combination clutch and brake is designed
for maximum heat dissipation. This important feature
significantly reduces wear on the clutch and brake, allows
high start/stop frequency capability and high allowable
rotational speed.
The HI PRO clutch and brake has only a fraction of the inertia
found in other clutch and brake units where the clutch and
brake must be started and stopped at every cycle. The
brake portion of the unit is stationary, therefore in starting or
stopping, there is minimum inertia to be overcome. Large air
flow passages enable natural convection currents to
dissipate heat.
Fast stopping times of the brake protect expensive dies.
If either the air or electrical supply fails, the clutch will
automatically disengage and the brake is applied. For ease
of replacement, split clutch and brake linings are standard.
Cross section of
HI PROTM clutch
and brake.
Double-Wall
Construction
The end frames of a Heim press
brake are constructed with a
double-wall design for years of
continued component alignment.
This box-type design provides
maximum stability and support by
resisting deflections, twisting
motions and vibrations. While
under load, the frame assures
accuracy of part production and
maximum die life.
The HI PRO clutch and brake.
Circular guides control the movement of
the ram for the full length of each stroke.
Ram Guidance
For maximum accuracy, the ram of a
Heim press brake is guided by circular
guides with bronze bushings along 100%
of the travel. This feature guides the
movement of the ram for the full length of
each stroke. Left-to-right and front-toback tolerances are controlled, assuring
proper ram and bed alignment.
Maintaining parallel alignment protects
dies and assures quality part produchtion.
Massive circular guide
and connecting bolt.
SPECIFICATIONS
Tonnage in shaded
areas are for V die
openings eight times
the mental thickness.
TONNAGE TABLE
For more information contact:
The Heim Group 6360 West 73rd Street, Chicago, Illinois 60638
708-496-7450 Fax 708-496-7428 Parts Fax 708-496-0708
The Heim Group reserves the right to change the design or details of its products without notice. Point of operation safety guarding or devices are the sole responsibility of the
employer (user) of the machine as provided in ANSI B-11 1-2001 as published by the American Standards Institute Inc., 1430 Broadway, New York , NY 10018 and OSHA regulations.
Cat MPB-32-5-93 4M copyrigh 1993 Heim L.P.
Adjustable Bed • 40 and 60 Tons
Rousselle Two Point Gap Frame Adjustable Bed
Standard Features
• Steel Fabricated
• Air Clutch
• Shoe Brake
• Wrist Pin Connection
• V Gibbing
• Air Counterbalance System
• Eccentric Shaft Motion
• Bolster Plate
• One Shot Lubrication
• Manual Slide Adjustment
• Solid State Press Control (ANSI B11.1)
• Nema 12 Enclosure Mounted on Press
• Operator Station with Dual Run, Emergency
•
•
•
•
•
•
•
Stop and Stop on Top Palm Buttons
Supervisory Key Selector Switch for Off,
Single Stroke, Inch or Continuous Mode
Brake Monitor
Motion Detector
Dual Air Valve
Pressure Switches for Clutch/Brake and
Counterbalance
Forward/Reverse Feature
Stroke Counter
Optional Features
• Self-Monitoring Automatic Lubrication System
• Powered Slide Adjustment with Digital Position Indicator
• Stroke Lengths other than Standard
• Additional Shut Heights
• Custom Bed Sizes
• T-Slotted Bolster
• Bolster Burnout
• Special Drilling and Machining
• Custom Speeds
• Variable Speed Drive
• Remote Mounted Controls
• Tonnage Monitor
• Additional Operator Station
Model 6W60
Specifications
Model Number
4W48
6W48
6W60
6W76
40
60
60
60
48 x 14
48 x 16
60 x 16
76 x 16
Non-Geared
105
110
110
110
Geared
45
50
50
50
Capacity (Tons) B.D.C.
Area of Bed (Left-to-Right x Front-to-Back)
Strokes Per Minute
Shut Height S.D.A.U.
Refer to Shut Height Charts
Slide Adjustment
None
3
3
Bed Adjustment
13
14 ⁄2
14 ⁄2
14 1⁄2
1
3
1
Bed Opening
32 x 12
34 x 13
46 x 13
62 x 13
Slide Area
37 x 9 ⁄4
36 x 16
48 x 16
64 x 16
Depth of Bed
14
18
20
22 1⁄2
Width of Opening Through Back
34
34
46
62
Depth of Throat from Center Line of Slide
6 ⁄4
8 ⁄4
8 ⁄4
8 1⁄4
Main Bearing
3 1⁄4
4 1⁄4
4 1⁄4
4 1⁄4
Connecting Rod
6 1⁄4
7 1⁄4
7 1⁄4
7 1⁄4
Non-Geared
33
38
38
38
Geared
22
22
22
22
Non-Geared
800
1050
1050
1050
Geared
250
250
250
250
3
5
5
5
Non-Geared
1175
1175
1175
1175
Geared
1750
1750
1750
1750
Minimum
29
30 ⁄4
30 ⁄4
30 1⁄4
Maximum
42
44 3⁄4
44 3⁄4
44 3⁄4
111
121
121
121
Left-to-Right
46 ⁄4
48
60
76
Front-to-Back
40 ⁄2
47 ⁄4
47 ⁄4
47 1⁄4
1
3
1
1
Crankshaft Diameter
Flywheel Diameter
Flywheel Weight (lbs.)
Motor Horsepower
Motor Speed (RPM)
1
1
Floor to Top of Bed
Overall Height with Standard Stroke
3
Floor Space at Base
1
1
1
Shut Height Charts
4W Shut Height Chart
6W Shut Height Chart
Stroke
Shut Height Range Stroke Down Adjustment Up
Stroke
Shut Height Range Stroke Down Adjustment Up
1”
5 ⁄4 – 18 ⁄4
1”
7 1⁄2 – 22
2”
4 3⁄4 – 17 3⁄4
2”
7 – 21 1⁄2
3”
3 3⁄4 – 16 3⁄4
3”
6 3⁄4 – 21 1⁄4
4”
2 3⁄4 – 15 3⁄4
4”
5 3⁄4 – 20 1⁄4
5”
1 3⁄4 – 14 3⁄4
5”
4 3⁄4 – 19 1⁄4
1
1
Standard shut heights shown in green with standard stroke. Values in inches unless otherwise noted. Machines may vary slightly from those shown.
www.theheimgroup.com • 6360 West 73rd Street, Chicago, IL 60638
Sales/Service: 708-496-7400 • 800-927-9393 • Fax: 708-496-7428 • Parts Fax: 708-496-0708 • Email: [email protected]
The Heim Group reserves the right to change design or detail of its products without notice. Point of operation safety guarding or devices are the sole responsibility of the employer (user) of the machine as provided in ANSI B11.1 (2001)
as published by the American National Standards Institute, Inc. and OSHA regulations. “Heim” and “Rousselle” are Reg. TM's; “Stamping Out Downtime” is a TM of The Heim Group. ©THG, 2008. All Rights Reserved.
Deep Throat & Adjustable Bed Horn • 15 to 60 Tons
Rousselle Deep Throat & Adjustable Bed Horn Presses
Model 40H
Standard Features
• Cast Frame (F and G Models) Steel Frame (40 and 60 Ton) Horns
• Air Clutch and Shoe Brake
• Crankshaft Motion (40 and 60 Ton)
• Eccentric Shaft Motion (15 and 25 Ton Models)
• Wrist Pin Connection
• V Gibbing
• Air Counterbalance System (60 Ton and Up)
• Bolster Plate
• Manual Grease Lubrication
• Solid State Press Control (ANSI B11.1)
• Nema 12 Enclosure Mounted on Press
• Operator Station with Dual Run, Emergency Stop and
•
•
•
•
•
•
•
Optional Features
• One Shot Lubrication System
• Self-Monitoring Automatic Lubrication System
• Stroke Lengths other than Standard
• T-Slotted Bolster
• Bolster Burnout
• Special Drilling and Machining
• Pneumatic Flywheel Brake
• Shaft Extension
• Custom Speeds
• Variable Speed Drive
• Bar Turnover with Key Selector Switch
• Pedestal for Operator Station
• Tonnage Monitor
• Remote Mounted Controls
• Additional Operator Station
Stop on Top Palm Buttons
Supervisory Key Selector Switch for Off, Single Stroke,
Inch or Continuous Mode
Brake Monitor
Motion Detector
Dual Air Valve
Pressure Switches for Clutch/Brake and Counterbalance
Forward/Reverse Feature
Stroke Counter
Model 2G
Specifications
Model Number
2F
2G
Capacity (Tons) Near B.D.C.
4F
4G
6F
6G
15H
25H
40H
25
40
60
15
25
16 x 11
20 x 14
26 x 16
30 x 18
16 x 11
20 x 14 ⁄2
26 x 16 1⁄2
160
135
105
110
160
135
105
–
–
45
50
–
–
45
1”
–
–
13 ⁄2
–
–
6 ⁄4 - 18 3⁄4
1 1⁄4”
–
–
–
–
–
–
–
1 ⁄4”
–
–
–
Non-Geared
Geared
Stroke
3
Shut Height
S.D.A.U.
3G
15
Bed Area (Left-to-Right x Front-to-Back)
Strokes
Per Minute
3F
13
–
13 ⁄2
1
1
40
1
–
–
3
–
2”
8
7 ⁄4
10 ⁄4
10 ⁄4
12 ⁄2
13
13
13
4 ⁄2 - 12
4 ⁄4 - 15 ⁄4
6 ⁄4 - 18 1⁄4
3”
7
6 3⁄4
9 3⁄4
9 3⁄4
12
12 1⁄2
12 1⁄2
12 1⁄2
3 1⁄2 - 11
3 1⁄4 - 14 1⁄4
5 3⁄4 - 17 3⁄4
3
3
3
1
1
1
1
1
4”
–
8 3⁄4
8 3⁄4
11
11 1⁄2
11 1⁄2
11 1⁄2
–
2 1⁄4 - 13 1⁄4
4 3⁄4 - 16 3⁄4
5”
–
–
10
10 1⁄2
10 1⁄2
10 1⁄2
–
–
–
3 3⁄4 - 15 3⁄4
6”
–
–
9
9 1⁄2
9 1⁄2
9 1⁄2
–
–
–
2 3⁄4 - 14 3⁄4
Bolster Thickness
1 1⁄4
1 1⁄2
1 3⁄4
2
Optional
Optional
Optional
Slide Adjustment
1 ⁄2
2
3 ⁄2
3 ⁄2
1 ⁄2
2
3 1⁄2
15 x 101⁄2 141⁄2 x 11
16 x 10 1⁄2
8 x6
10 x 7
14 x 10 1⁄2
12 1⁄2
8
10
12 1⁄2
1
Rectangular
1
101⁄4 x 61⁄4
11 x 6
12 x 7
8 1⁄2
9
10
Width of Opening Through Back (Hole Diameter)
10 1⁄2
–
12 1⁄4
Depth of Throat from Center Line of Slide
12 1⁄2
18 1⁄2
15 1⁄4
Bed
Opening
Round
Width Across Slide Ears
Crankshaft
Diameter
Flywheel
Diameter
Flywheel
Weight (lbs.)
Die Shank
Hole Diameter
Floor Space
at Base
1
12 1⁄2
–
8
15
–
16
–
(3)
(4)
(5)
18 1⁄2
18 1⁄2
24 1⁄2
21 1⁄2
24 1⁄2
5 1⁄2
6 3⁄4
8 1⁄2
6 1⁄2
8 1⁄4
12
12
6 1⁄2
8 1⁄4
12
Main Bearing
1 1⁄2
2 1⁄2
3 1⁄4
4 1⁄4
1 1⁄2
2 1⁄2
3 1⁄4
Connecting Rod
3 7⁄8
5 3⁄8
5
5
3 7⁄8
5 3⁄8
5
Non-Geared
18 1⁄2
24
33
38
18 1⁄2
24
33
–
–
21 1⁄2
21 1⁄2
–
–
21 1⁄2
200
370
800
1050
200
370
800
–
–
225
225
–
–
225
Standard
9
1 ⁄16
9
1 ⁄16
2
2
9
1 ⁄16
9
1 ⁄16
2
Maximum
2
2
2 ⁄2
1
2 ⁄2
2
2
2 1⁄2
1
2
3
5
1
2
3
1750
1175
1175
1175
1750
1175
1175
–
–
1750
1750
–
–
1750
Geared
Non-Geared
Geared
Motor Horsepower
Motor Speed
(RPM)
1
Non-Geared
Geared
1
Left-to-Right
31
20
35
24
41
26
41
30
20
24
28
Front-to-Back
42
34
56
40
56
52
68
57
24
28
32
Specifications vary by frame only where indicated. Standard shut heights shown in green type with standard stroke. Values in inches unless
otherwise noted. Consult factory for 60 Ton Horn Press specifications. Machines may vary slightly from those shown.
www.theheimgroup.com • 6360 West 73rd Street, Chicago, IL 60638
Sales/Service: 708-496-7400 • 800-927-9393 • Fax: 708-496-7428 • Parts Fax: 708-496-0708 • Email: [email protected]
The Heim Group reserves the right to change design or detail of its products without notice. Point of operation safety guarding or devices are the sole responsibility of the employer (user) of the machine as provided in ANSI B11.1 (2001)
as published by the American National Standards Institute, Inc. and OSHA regulations. “Heim” and “Rousselle” are Reg. TM's; “Stamping Out Downtime” is a TM of The Heim Group. ©THG, 2008. All Rights Reserved.