Knife Edge Cove Installation Guide

Transcription

Knife Edge Cove Installation Guide
Knife Edge Cove
Installation Instructions
Components supplied with housings
Pre-installation:
Inspect material to verify all material has been received.
Report shipping damage or missing items immmediately.
KEC-A-CON-FLAT
Flat connector w/4 x M4
set screws
Organize all material by ‘System’ using BOM per System.
KEC-A-CON-SQR
Square connector
w/4 x M3 set screws
Linear
Housing
KEC-A-HSG-X (X can be any 1' length betwen 1' and 8')
Corner
Housings
12”
12”
12”
KEC-A-C90C
90 deg. coffer corner (inside corner)
12”
KEC-A-C90R
90 deg. raft corner (outside corner)
KEC-A-HSG-X
KEC-A-CON-FLAT
Flat Connector
KEC-A-CON-SQR
Square Connector
KEC-A-HSG-X
Straight Linear Wall to Wall
ECOSENSE LIGHTING INC.
915 WILSHIRE BLVD
SUITE 2175
LOS ANGELES, CA 90017
P • 310 . 496 . 6255
F • 310 . 496 . 6256
T • 855 . 632 . 6736
855 . 6 . ECOSEN
SPECIFICATIONS SU B J EC T TO CHANG E WITHOUT
NOTICE . VISIT ECOSENSELIG HTING.COM FOR
TH E MOST CU RRENT SPECIFICATIONS .
© 2015 ECOSENSE LIG HTING INC . ALL RIG HTS RESERVED.
ECOSENSE , TH E ECOSENSE LOGO AN D ECOSPEC ARE
REGISTERED TR ADEMARKS OF ECOSENSE LIG HTING INC .
ECOSENSELIG HTING.COM
1
Knife Edge Cove
Installation Instructions
KEC-A-C90C
KEC-A-HSG-X
KEC-A-HSG-X
mounting surface
typical
mounting surface
typical
KEC-A-C90C
KEC-A-CON-SQR
Square Connector
KEC-A-C90C
KEC-A-CON-FLAT
Flat Connector
mounting surface
typical
KEC-A-HSG-X
KEC-A-HSG-X
mounting surface
typical
Coffer Cove, 4 sided with coffer corner (inside corners)
KEC-A-C90C
KEC-A-C90R
KEC-A-HSG-X
KEC-A-HSG-X
mounting surface
typical
mounting surface
typical
KEC-A-C90R
KEC-A-CON-FLAT
Flat Connector
KEC-A-C90R
KEC-A-CON-SQR
Square Connector
mounting surface
typical
KEC-A-HSG-X
KEC-A-HSG-X
KEC-A-C90R
Raft Cove, 4 sided with raft corner (outside corners)
ECOSENSE LIGHTING INC.
915 WILSHIRE BLVD
SUITE 2175
LOS ANGELES, CA 90017
P • 310 . 496 . 6255
F • 310 . 496 . 6256
T • 855 . 632 . 6736
855 . 6 . ECOSEN
SPECIFICATIONS SU B J EC T TO CHANG E WITHOUT
NOTICE . VISIT ECOSENSELIG HTING.COM FOR
TH E MOST CU RRENT SPECIFICATIONS .
© 2015 ECOSENSE LIG HTING INC . ALL RIG HTS RESERVED.
ECOSENSE , TH E ECOSENSE LOGO AN D ECOSPEC ARE
REGISTERED TR ADEMARKS OF ECOSENSE LIG HTING INC .
ECOSENSELIG HTING.COM
2
Knife Edge Cove
Installation Instructions
Rough-in
Wall Preparation:
framing member
1. Begin installation by providing rough-in wall and
ceiling structure for each ‘System’ location.
2. Install 5/8” drywall onto upper ceiling and cove wall.
framing member
3. Tape and mud joints. Sand to smooth finish and
apply paint primer and paint color.
5 5/8”” minimum
framing member
Framing
upper ceiling
upper ceiling
5/8” drywall
5/8” drywall
Finished Wall
Finished Wall
lower ceiling
Finished Mounting Surface
ECOSENSE LIGHTING INC.
915 WILSHIRE BLVD
SUITE 2175
LOS ANGELES, CA 90017
P • 310 . 496 . 6255
F • 310 . 496 . 6256
T • 855 . 632 . 6736
855 . 6 . ECOSEN
SPECIFICATIONS SU B J EC T TO CHANG E WITHOUT
NOTICE . VISIT ECOSENSELIG HTING.COM FOR
TH E MOST CU RRENT SPECIFICATIONS .
© 2015 ECOSENSE LIG HTING INC . ALL RIG HTS RESERVED.
ECOSENSE , TH E ECOSENSE LOGO AN D ECOSPEC ARE
REGISTERED TR ADEMARKS OF ECOSENSE LIG HTING INC .
ECOSENSELIG HTING.COM
3
Knife Edge Cove
Installation Instructions
Mounting Housing
Housing Installation:
1. Mount housing onto finished mounting surface (cove wall)
with #8 screws at 16” on center using continuous screw port
located in housing. (Do not use drywall screws. Use wood or sheet
Joint Connector
metal screws)
Pre-drilling pilot hole to align with structure is recom
mended to simplify mounting
Nose Housing
Recommend starting at end of straight runs and at the a
corner for patterns.
Joint Connector 2. Screws shall fasten to wall/ceiling building framing members.
Total fixture weight 1.5 lbs per foot.
Attaching Housing to Mounting Surface
Increase weight as required to accomodate light fixtures
supplied by others.
3. Mount additional housings as indicated in #3 above with the
addition of sliding the pre-installed joint connector and nose
alignment connector to attach joining extrusions.
1 1/4” Drywall
Screw
4. Secure connectors in place with four set screws (two set
screws on each side of the joint).
5. Install all housings within a given ‘System’ repeating # 3 and
#4 above.
1 3/8”
1 7/8”
Drywall Installation under Housing
5/8” Drywall
Ceiling
6. Install 5/8” drywall to the underside of the housing and fasten
with 1 1/4” drywall screw 1 7/8” from housing nose edge.
7. Apply drywall mud and mesh tape to form a smooth taper from
housing nose edge to ajoining ceiling plan or wall surface.
Apply multiple thin coats of mud to ensure a smooth taper.
Allow each coat to dry and sand smooth before applying the
next coat of mud.
8. Apply paint primer and paint color.
Feild Cutting: If cutting the housing extrusion in the feild use a non-ferrous blade.
Important:
Drywall Mud Skim Coat
ECOSENSE LIGHTING INC.
915 WILSHIRE BLVD
SUITE 2175
LOS ANGELES, CA 90017
Plaster
Skim
Coat
P • 310 . 496 . 6255
F • 310 . 496 . 6256
T • 855 . 632 . 6736
855 . 6 . ECOSEN
Housing lengths are based on finished mounting surface dimensions as
approved on submittal drawings. Any deviation in the finished mounting
surface dimension will result in housings being too long or too short. If
this occurs new hous-ings will need to be ordered with the exact length
required to complete the ‘System(s)’.
SPECIFICATIONS SU B J EC T TO CHANG E WITHOUT
NOTICE . VISIT ECOSENSELIG HTING.COM FOR
TH E MOST CU RRENT SPECIFICATIONS .
© 2015 ECOSENSE LIG HTING INC . ALL RIG HTS RESERVED.
ECOSENSE , TH E ECOSENSE LOGO AN D ECOSPEC ARE
REGISTERED TR ADEMARKS OF ECOSENSE LIG HTING INC .
ECOSENSELIG HTING.COM
4