RS3200 Plus Security System - Sparks Toyota

TOYOTA
FJ CRUISER
2008 -
TVIP V5
Preparation
RS3200 PLUS
Part Number: PT398-35080
NOTE: Part number of this accessory may not be the same as
the part number shown.
Conflicts
Recommended Tools
Do not be installed in vehicles with factory Anti-theft
alarm, or Vehicle without Factory Keyless Entry Systems.
Recommended Sequence of Application
Item #
1
2
Accessory Description
TVIP V5 RS3200 PLUS
RSE
DVD Headrest RSE
Installation Tools
Phillips Screwdriver
Kit Contents
Item # Quantity
1
1
2
1
3
1
4
1
Description
Wire Harness
V5 ECU Mounting Bracket
GBS ECU Mounting Bracket
Extra Large Wire Tie
Flatblade Screwdriver
Nylon Panel Removal Tool
Quantity
1
1
1
15
1
2
1
5
2
2
1
1
1
Description
V5 ECU
GBS ECU
Microphone
Wire Ties
Screw(M5 Size: For GBS ECU)
Washer
Screw (M6 Size: For V5 ECU)
Foam Tapes
Window Labels (English)
Window Labels (Spanish)
Splicing Connector
Owner’s Manual
Warranty Card
Additional Items Required For Installation
Item #
1
Quantity Reqd.
1
Notes
(Optional)
Blankets, Part Boxes
Notes
CAD-E IADS P/N ALL 02016-01
Notes
#2, screwdriver or tip
#2 Offset Screwdriver
¼” Flat Blade,
1/8” Flat Blade,
e.g. Panel Pry Tool #1
Toyota SST # 00002-06001-01
Socket
Hardware Bag Contents
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
Personal & Vehicle
Protection
Safety Glasses
Safety Gloves
Vehicle Protection
Special Tools
Striker Tool (PPO only)
Description
Black Electrical Tape
Wrench
Side Cutters
Tape
Torque Wrench
Special Chemicals
Glass Cleaner
10mm, Deep 10mm,
Extension
10mm
Clear
36 in•lbf (4.07 N•m)
Notes
Household Windex
Legend
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION: A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT: Used in Figures calls out the
specific tools and equipment recommended for this
process.
REVISION MARK: This mark highlights a change in
installation with respect to previous issue.
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as:
• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
• Safety (eye protection, rechecking torque procedure, etc.).
• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).
• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).
Please see your Toyota dealer for a copy of this document
Issue: B
10/24/07
Page 1 of 25 pages
Issue: B
10/24/07
4P WHITE
40P WHITE
B
○
C
○
20P WHITE
8P WHITE
E
○
F
○
4P BLACK
H
○
Wire Harness Outline (Passenger Compartment)
Page 2 of 25 pages
Wire
J
○
(GREEN/RED Wire)
4P BLUE
I
○
FJ CRUISER
(For Microphone)
GBS ECU
G
○
(For GBS ECU)
V5 ECU
D
○
(For V5 ECU)
GROUND
TERMINAL
A
○
TOYOTA
Procedure
2008 RS3200 PLUS
TVIP V5
TOYOTA
FJ CRUISER
2008 -
TVIP V5
Procedure
RS3200 PLUS
1. Vehicle Disassembly.
(a) Automatic Vehicles should be placed in
Park with the Parking Brake set.
10mm Socket
Negative Battery
Cable
(b) Remove the Negative Battery Cable.
(Fig. 1-1)
(1) Protect the Fender before starting.
(2) Note the Battery Cable position, as it will be
reinstalled in the same position.
Battery
CAUTION: Do not touch the positive terminal.
Fig. 1-1
10/24/07
DS Step Cover
2
DS Register Assembly
3
DS Lower Dash Cover
4
Metal Substructure
5
Center Cluster Trim
6
Center Cluster Trim
7
Heater Control Panel
8
Brake Hole Cover
9
Center Console Separator
10
Console Upper Panel
11
Cen. Cluster Lower Cover
12
PS Step Cover
13
PS Cowl Cover
14
Glove Box
15
Glove Box Upper Cover
Remove all corresponding
connectors accordingly as
you disassemble.
Fig. 1-2
Issue: B
1
Page 3 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
TVIP V5
RS3200 PLUS
(c) Remove the Driver Side Step Cover.
(Fig. 1-3)
Nylon Panel Removal Tool
(1) Open the Driver’s Side Rear Door.
(2) Protect the Vehicle Interior with Blankets.
Step Cover
Fig. 1-3
Nylon Panel Removal Tool, 10mm Socket, Extension
(d) Loosen the Driver Side Cowl Cover to
expose the Bolt. (Fig. 1-4)
(1) Do not put too much stress on the Cowl Cover.
(e) Remove 1 Bolt. (Fig. 1-4)
Bolt
Foot Rest
Cowl Cover
Fig. 1-4
Nylon Panel Removal Tool
1
(f) Remove the Register Assembly. (Fig. 1-5)
(1) Start from the top.
Register
Assembly
2
Fig. 1-5
10mm Socket
(g) Remove the Lower Dash Cover. (Fig. 1-6)
Bolt
(2) Hold down the Claw, and pull out to remove the
Hood Release Lever.
Claw
Lower Dash Cover
Fig. 1-6
Issue: B
10/24/07
(1) Remove 1 Bolt.
Hood
Release
Lever
Page 4 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
TVIP V5
RS3200 PLUS
10mm Socket
(h) Remove the Metal Substructure. (Fig. 1-7)
Bolt
(1) Remove 4 Bolts.
CAUTION: Sharp metal edges.
Bolts (x2)
Bolt
Fig. 1-7
Metal Substructure
Nylon Panel Removal Tool
Side Garnish
(i) Remove both Trim Pieces on the Center
Cluster Area. (Fig. 1-8)
(1) Remove 2 Screws.
Side Garnish
Fig. 1-8
Screw
Phillips Screwdriver
Screw
Heater Control
Panel
(j) Remove the Heater Control Panel.
(Fig. 1-9)
(1) Remove 2 Screws.
Screws (x2)
Fig. 1-9
FOR MANUAL TRANSMISSION MODELS
ONLY. (Step k-m)
Nylon Panel Removal Tool
Gear Shift
Knob
(l) Remove the Parking Brake Hole Cover from
the Floor Console Box. (Fig. 1-10)
Parking Brake
Hole Cover
Floor Console
Box
Fig. 1-10
Issue: B
10/24/07
(k) Remove the 2 Gear Shift Knobs. (Fig. 1-10)
(m) Remove the Console Upper Panel.
(Fig. 1-10)
Console
Upper Panel
Page 5 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
TVIP V5
RS3200 PLUS
Nylon Panel Removal Tool
FOR AUTOMATIC TRANSMISSION
MODELS ONLY. (Step n-r)
4x4 Shift Knob
(n) Remove 4x4 Shift Knob. (Fig. 1-11)
Console
Upper Panel
(1) Move Shift Lever out of Park.
(o) Remove the Parking Brake Hole Cover from
the Floor Console Box. (Fig. 1-11)
Parking Brake
Hole Cover
Floor
Console
Box
Fig. 1-11
(p) Remove the Console Upper Panel.
(Fig. 1-11)
(q) Temporarily reinstall the Shift Knob.
(Fig. 1-11)
(r) Move the Gear Shift Lever into Park.
10mm Socket
Bolt
Separator
(s) Remove the Center Console Separator from
the Center Console. (Fig. 1-12)
(t) Move the Driver’s Seat back, and tilt the
Seat and Armrest as far back as possible.
Then, slide the Center Console towards the
back of the Vehicle. (Fig. 1-12)
Bolt
Bolt
Bolt
Center
Console
(1) Remove 4 Bolts.
Fig. 1-12
10mm Socket, Nylon Panel Removal Tool
Center Cluster
Lower Cover
Clip
Harness
Clamp
Bolt
Clip
Fig. 1-13
Issue: B
10/24/07
Knockout
Cover
(u) Remove the Center Cluster Lower Cover.
(Fig. 1-13)
(1) Remove 2 Bolts and 2 Clips.
(2) Remove the Backside of the Vehicle Harness
Clamp from the Center Cluster Lower Cover.
(v) Remove the Knockout Cover of the Center
Cluster Lower Cover in the bottom row, 4th
space from the left. (Fig. 1-13)
Bolt
(1) Discard the Knockout Cover.
Page 6 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
TVIP V5
RS3200 PLUS
(w) Open the Passenger’s Side Rear Door.
(Fig. 1-14)
Nylon Panel Removal Tool
(x) Remove the Passenger’s Side Step Cover.
(Fig. 1-14)
(1) Protect the Vehicle Interior with Blankets.
Step Cover
Fig. 1-14
(y) Remove the Passenger Side Cowl Cover.
(Fig. 1-15)
Nylon Panel Removal Tool
(1) Remove 1 Nut.
Cowl Cover
Fig. 1-15
Nut
Glove Box
Damper Lever
(z) Remove the Glove Box Assembly.
(Fig. 1-16)
(1) Open the Glove Box Door, and release the
Damper Lever.
(aa) Remove the Glove Box Upper Panel.
(Fig. 1-17)
Fig. 1-16
(1) Remove 1 Screw.
Phillips Screwdriver, Small Flat Blade Screwdriver
Glove Box Upper Cover
Screw
(bb) Remove 2 Joint Connectors and Air Bag
Connector (with black cover) from the
backside of the Glove Box Panel. (Fig. 1-17)
(1) Using a Small Flat Blade Screwdriver, release
the Joint Connector Locks.
Air Bag
Connector
Fig. 1-17
Issue: B
10/24/07
Joint
Connectors
(2) Press in on the 2 Clips securing the Air Bag
Connector.
CAUTION: Do not disconnect the air bag
connector.
Page 7 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
TVIP V5
RS3200 PLUS
2. V5 Harness Installation.
V5 Harness
(a) Route the V5 4P BLUE Connector and
GREEN/RED Wire, from Center Cluster
toward the Driver’s Side Area. (Fig. 2-1)
V5 Harness’s
20P WHITE
Fig. 2-1
Vehicle Harness Clamp
Side Cutter
Wire Tie
V5 Harness
V5 Harness’
White Tape
(b) Use 1 Wire Tie to secure the White Taped
Marker on the V5 Harness to the Vehicle
Harness Clamp near the Steering Shaft.
(Fig. 2-2)
(c) Secure the V5 Harness to the Vehicle 8P
Connector Harness with 1 Wire Tie.
(Fig. 2-2)
Fig. 2-2
Vehicle Harness’s 4P
BLUE Connector
(d) Disconnect the Vehicle 4P BLUE Connector
near the Steering Shaft. (Fig. 2-3)
Fig. 2-3
Side Cutter
Wire Tie
V5 4P
BLUE
Fig. 2-4
Issue: B
Vehicle 4P BLUE
10/24/07
Vehicle 4P
BLUE
(e) Plug in the V5 4P BLUE Connectors
between the Vehicle 4P Connectors.
(Fig. 2-4)
(f) Secure the 4P Connectors to the Vehicle
Harness near the Steering Shaft with 1 Wire
Tie. (Fig. 2-4)
V5 4P BLUE
Page 8 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
Loose 24P WHITE
Disconnected
30P WHITE
(g) Loosen the Middle 24P WHITE Connector
on the right side of the Driver’s J/B.
(Fig. 2-5)
(h) Disconnect the Lower 30P WHITE
Connector on the right side of the Driver’s
J/B. (Fig. 2-5)
Driver’s Side J/B
Fig. 2-5
(i) Remove the Tape from the 30P Connector.
(Fig. 2-6)
Pliers
GREEN/RED
30P
30P
Tape
Wire Side View
30P
(j) Locate the 30P Connector’s GREEN/RED
Wire (top row, fifth space from the left).
Attach the V5 GREEN/RED Wire with a
Splicing Connector. (Fig. 2-6)
(1) Verify the Terminal is inserted and seated
properly.
Splicing
Connector
Fig. 2-6
V5 Harness’s
GREEN/RED Wire
Splicing Connector
Side Cutter
(k) Wrap the Splicing Connector to the Vehicle
Harness with the Electrical Tape. (Fig. 2-6)
(l) Reconnect the Lower and Middle
Connectors on right side of Driver’s J/B.
(Fig. 2-7)
V5 Harness
Driver’s side J/B
24P (White)
30P (White)
(1) Verify secure connection.
(m) Secure the V5 Harness’s excess
GREEN/RED Wire to Vehicle’s Harness
with 1 Wire Tie. (Fig. 2-7)
GREEN/RED Wire
Fig. 2-7
TVIP V5
RS3200 PLUS
Vehicle’s Black
Main Harness
Wire Tie
GO BACK TO THE CENTER CLUSTER AREA
Side Cutter
Wire Tie
(n) Secure the V5 Harness to the Vehicle’s
Harness with 1 Wire Tie. (Fig. 2-8)
Vehicle’s Harness
V5 Harness’s
20P WHITE
Fig. 2-8
Issue: B
10/24/07
Page 9 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
TVIP V5
RS3200 PLUS
(o) Plug in the V5 20P WHITE Connectors
between the Vehicle 20P Connectors
(Fig. 2-9)
Wire Tie
Side Cutter
Vehicle’s 20P
WHITE
(p) Secure the 20P WHITE Connectors to the
Vehicle Harness with 1 Wire Tie. (Fig. 2-9)
V5 20P WHITE
Fig. 2-9
Side Cutter
V5 Harness
(q) Route the V5 Harness toward the Glove Box
Area.
Wire Tie
Vehicle Harness
Fig. 2-10
Flat Blade Screwdriver
(r) Secure it to the Vehicle Harness with 1 Wire
Tie. (Fig. 2-10)
V5 Harness
GBS Setting
3. GBS ECU Preparation and Installation.
(a) Turn the GBS Adjustment Screw on the
GBS ECU to the “6” position. (Fig. 3-1)
GBS ECU
Fig. 3-1
GBS ECU Mounting Bracket
(b) Insert the GBS ECU Mounting Bracket into
the indicated Slot of the GBS ECU.
(Fig. 3-2)
(1) Insert the Mounting Bracket into the correct
ECU’s Slot.
(2) The Bracket is permanently attached once
installed.
GBS ECU
Fig. 3-2
Issue: B
10/24/07
(3) Ensure the Bracket is firmly attached to the
ECU.
Page 10 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
(c) Attach 2 pieces of Foam Tape onto the GBS
ECU as shown. (Fig. 3-3)
GBS ECU
GBS ECU
Mounting Bracket
Fig. 3-3
TVIP V5
RS3200 PLUS
Foam Tapes
(x2)
(d) Dislodge the Noise Filter. (Fig. 3-4)
Phillips Screwdriver
(1) Remove 2 Screws.
Noise Filter
Vehicle
Harness’
8P (White)
Screws
(x2)
Fig. 3-4
(e) Put the GBS ECU Assembly through the
opening at the bottom of the Center Cluster
Area. (Fig. 3-5)
Fig. 3-5
Issue: B
GBS ECU
10/24/07
Page 11 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
TVIP V5
RS3200 PLUS
GBS ECU
ONLY FOR VEHICLES THAT WILL ALSO
HAVE THE DVD HEADREST RSE SYSTEM
INSTALLED. (Step f-n)
(f) Locate the Boss on the Upper Part of the
Heater Unit. Loosely install the GBS ECU
Mounting Bracket and Noise Filter using the
existing screw. (Fig. 3-6)
Screw
(1) Do not tighten the Screw yet.
Fig. 3-6
(g) Put 2 Washers between the Noise Filter’s
Bracket and Boss. Loosely secure it with
existing Screw. (Fig. 3-7)
(1) Do not forget the Washers, when re-installing the
Noise Filter.
Screw
Fig. 3-7
(h) Install the RSE Audio Interface Module
(AIM) Bracket.
(1) Refer to the DVD Headrest RSE Installation
Instructions (PN: PT900-35070) for additional
information on this process.
(i) Place the GBS Bracket onto the AIM
Bracket’s Stud as shown. (Fig. 3-8)
Fig. 3-8
AIM Bracket
(j) Place the AIM unit on the AIM Bracket
Studs. (Fig. 3-9)
(k) Secure the AIM unit to the AIM Bracket as
described in the DVD Headrest RSE
Installation Instructions (PN: PT900-35070).
(Fig. 3-9)
AIM Unit
Fig. 3-9
Issue: B
10/24/07
(l) Tighten the GBS Bracket and Noise Filter
Screws.
Page 12 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
TVIP V5
RS3200 PLUS
8P Connector
(m) Connect the V5 Harness’s White 8P
Connector to the GBS ECU. (Fig. 3-10)
V5 Harness
(n) Secure the Microphone Connector’s
Harness to the Vehicles Noise Filter
Harness with 1 Wire Tie. (Fig. 3-11)
Fig. 3-10
Wire Tie (x2)
Microphone
Connector
Noise Filter
(o) Secure the excess Harness from the GBS
portion of the V5 Harness to the Main V5
Harness with 1 Wire Tie. (Fig. 3-11)
Fig. 3-11
Phillips Screwdriver
GBS Mounting Bracket
Boss
GBS ECU
Fig. 3-12
ONLY FOR VEHICLES THAT WILL NOT
HAVE THE DVD HEADREST RSE SYSTEM
INSTALLED. (steps o-u)
(p) Locate the Boss on the Bottom of the Heater
Unit, align it with 2 bottom Holes on the
GBS ECU Mounting Bracket. Loosely
install the GBS ECU with 1 M6 Screw
supplied. (Fig. 3-12)
Screw
(1) Do not tighten the Screw yet.
Phillips Offset Screwdriver
Boss
GBS ECU
(q) Locate the Boss on the Upper Part of the
Heater Unit. Loosely install the GBS ECU
Mounting Bracket and Noise Filter using the
existing screw. (Fig. 3-13)
(1) Do not tighten the Screw yet.
Noise Filter
Screw (existing)
Fig. 3-13
Issue: B
10/24/07
Page 13 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
TVIP V5
RS3200 PLUS
Noise Filter
Phillips Screwdriver
(r) Put 2 Washers between the Noise Filter’s
Bracket and Boss. Secure it with existing
Screw. (Fig. 3-14)
Boss
GBS ECU
(2) Verify the Screw is tightened securely.
Washers (x2)
Fig. 3-14
(1) Do not forget the Washer, when re-installing the
Noise Filter.
(s) Secure the 2 GBS ECU Mounting Bracket
Screws. (Fig. 3-14)
Screw (Existing)
GBS ECU
(t) Attach 1 piece of Foam Tape to the GBS
ECU Mounting Bracket as shown.
(Fig. 3-15)
GBS ECU
Mounting Bracket
Noise Filter
8P
Fig. 3-15
Foam Tape
Side Cutter
GBS ECU
V5 Harness
8P (White)
(u) Connect the V5 Harness’s White 8P
Connector to the GBS ECU. (Fig. 3-16)
(v) Secure the V5 Harness’s Black 4P
Connector Harness to the Vehicle’s Noise
Filter Harness with 1 Wire Tie. (Fig. 3-16)
4P (Black)
Fig. 3-16
Issue: B
10/24/07
Wire Tie
Page 14 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
4. V5 Harness Installation (continued).
Side Cutter
Reinforcement
Reinforcement
Vehicle Harness
Wire Tie
Vehicle
Harness
(a) Route the V5 Harness towards the right side
of the Glove Box Area. (Fig. 4-2)
(b) Secure the V5 Harness to the Vehicle
Harness with 1 Wire Tie. (Fig. 4-2)
V5 Harness
Fig. 4-2
TVIP V5
RS3200 PLUS
Wire Ties (x2)
(c) Secure the V5 Harness to the Vehicle
Reinforcement with 1 Wire Tie. (Fig. 4-2)
(1) Run the wire tie between the Reinforcement and
the Vehicle Harness.
Foam Tape
(d) Apply 1 piece of Foam Tape to the Brace in
the upper portion of the Glove Box Area as
showne. (Fig. 4-3)
Brace
Foam Tape
Brace
Fig. 4-3
5. V5 ECU Preparation and Installation.
(a) Insert the V5 ECU Mounting Bracket into
the indicated Bracket Slot on the V5 ECU.
(Fig. 5-1)
V5 ECU Mounting Bracket
(1) Insert the Mounting Bracket into the correct
ECU Slot.
V5 ECU
(2) The Bracket is permanently attached once
installed.
(3) Ensure the Bracket is firmly attached to the
ECU.
Fig. 5-1
V5 ECU Mounting Bracket
(b) Attach 1 piece of Foam Tape to the V5 ECU
Mounting Bracket. Fold the Foam Tape
around the Bracket as shown. (Fig. 5-2)
Foam Tape
V5 ECU
Fig. 5-2
Issue: B
10/24/07
Page 15 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
TVIP V5
RS3200 PLUS
(c) Locate and remove the Nut securing the
Connector Block, in the Glove Box Area.
(Fig. 5-3)
10mm, Deep Socket
Connector Block
(1) Do not discard the Nut.
Nut
Fig. 5-3
Bracket
(d) Connect the V5 White 40P Connector to the
V5 ECU. (Fig. 5-4)
(1) Verify secure connection.
V5 ECU
40P
V5 Harness
Fig. 5-4
(f) Position the V5 ECU Mounting Bracket
onto the Vehicle Bracket’s Stud Bolt as
shown.
ECU Mounting
Bracket
10mm Deep Socket, Phillips Screwdriver
Reinforcement
V5 ECU
Mounting
Bracket
Bracket
(2) Verify that the V5 ECU Mounting Bracket does
not interfere with the Vehicle’s Bracket.
Nut (Existing)
Issue: B
Screw
10/24/07
(g) Loosely install the V5 ECU Mounting
Bracket with Existing Nut. (Fig. 5-5)
(1) Do not tighten the Nut yet.
Stud Bolt
Fig. 5-5
(e) Put the V5 ECU behind the Dashboard
through the opening in the upper portion of
the Glove Box Area as shown. (Fig. 5-4)
(h) Secure the V5 ECU Mounting Bracket to the
Hole in the Reinforcement with 1 Screw
(M6 size) supplied. Tighten the existing Nut.
(Fig. 5-5)
Page 16 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
TVIP V5
RS3200 PLUS
6. V5 Harness Installation (continued).
V5 ECU
V5 ECU Mounting
Bracket
Side Cutter
Reinforcement
Brace
V5 Harness
Extra Large
Wire Tie
(a) Position the V5 Harness behind the Vehicle
Brace in the Glove Box Area. Secure it to
the Reinforcement with 1 Extra Large Wire
Tie. (Fig. 6-1)
(1) Put the Extra Large Wire Tie through the ECU
Mounting Bracket opening.
(b) Route the V5 Harness to the right side of the
Glove Box Area. Secure it to the Vehicle
Harness with 2 Wire Ties. (Fig. 6-1)
Wire Ties (x2)
Fig. 6-1
(c) Remove the Tape securing the Vehicle
White 4P Connector in the right side of the
Glove Box Area. (Fig. 6-2)
4P (White)
Tape
Fig. 6-2
Side Cutter
V5 Harness’ 4P
Wire Tie
V5 Harness
Vehicle
Harness’ 4P
V5 Harness’
Ground
Terminal
Fig. 6-3
10mm Wrench
Vehicle Harness’ Ground
Wire Terminal
(d) Plug the V5 White 4P Connector to the
Vehicle White 4P Connector. (Fig. 6-3)
(1) Verify Connectors are plugged in securely.
(e) Secure the 4P Connector to the Vehicle
Harness with 1 Wire Tie. (Fig. 6-3)
(f) Route the V5 Ground Terminal toward the
Passenger’s Side Cowl Area.
(Fig. 6-3)
(g) Locate and remove the Bolt securing the
Vehicle Ground Wire Terminal in the
Passenger’s Side Cowl Area. (Fig. 6-4)
(1) Do not discard the Bolt.
Bolt
Fig. 6-4
Issue: B
10/24/07
Page 17 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
10mm Wrench
V5 Harness
Vehicle Harness’ Ground
Wire Terminal
Bolt
(existing)
Fig. 6-5
TVIP V5
RS3200 PLUS
(h) Secure the V5 Ground Wire Terminal and
the Vehicle Ground Wire Terminals using
the existing Bolt.
(Fig. 6-5)
(1) Verify the Bolt is tightened securely.
V5 Harness’ Ground Wire Terminal
(i) Secure the V5 Harness to the Vehicle
Harness with 2 Wire Ties. (Fig. 6-6)
Side Cutter
V5 Harness
Wire Ties (x2)
Fig. 6-6
Center Cluster Cover
7. Microphone Installation.
(a) Insert the Microphone into the Knockout
Opening in the Center Cluster as shown.
(Fig. 7-1)
Rib
Clamp
Vehicle Harness
Fig. 7-1
V5 Harness’ 4P (Black)
Microphone
(b) Connect the V5 Black 4P Connector to the
Microphone. (Fig. 7-1)
(1) Verify Secure Connection.
(c) Reinstall the Center Cluster Cover.(Fig. 7-1)
(1) Connect any disconnected Connectors before
installing the Panel.
(2) Reattach the Vehicle Harness Clamp to the Rib
on the backside on the Center Cluster.
Issue: B
10/24/07
Page 18 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
TVIP V5
RS3200 PLUS
8. Window Label Installation
For US Vehicles use the English Labels and
discard the Spanish Labels.
For Mexico Vehicles use the Spanish Labels and
discard the English Labels.
Clear Tape
Lineup with
Bottom of
Window Etching
Window
Label
10mm
(a) Using Household Windex, clean the inside
of the Front Door Windows. (Fig. 5-1)
(1) When cleaning with Household Windex, follow
the Manufacture's Directions.
(b) Place the Warning Labels on the inside of
the Front Door Windows as shown.
(Fig. 5-1)
(1) Use a piece of clean adhesive tape to lift the
Labels off their protective backing.
CAUTION: do not touch the labels adhesive
surface.
(2) Line up the labels properly and place on the
glass. Do not attempt to reposition the Labels
once they and place.
(3) If the Label is begin installed with other Window
Labels align it horizontally with the other Labels
and 1-5mm from the last Label.
Issue: B
10/24/07
Page 19 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
10mm Socket
TVIP V5
RS3200 PLUS
9. Completing the Installation.
Cowl Cover
(a) Reassemble the Vehicle.
(1) Reconnect any Disconnected Connectors.
(2) Verify the Panels Fit Together properly with no
uneven Gaps between them.
(b) Confirm securing the Driver’s Side Cowl
Cover Ribs and the Vehicle’s Claw.
(Fig. 9-1)
Bolt
Fig. 9-1
(c) Clean up and remove any trash.
(d) Verify the Short Pin is installed. (Fig. 9-2)
(1) If not install now.
Short Pin
Fig. 9-2
Torque Wrench
(e) Position the Negative Battery Cable at the
original factory position. (Fig 9-3)
Negative
Battery
Cable
(1) Tighten the Nut to 36 in•lbf. (4.07 N•m)
CAUTION: Do not touch the positive terminal.
Battery
Fig. 9-3
(f) Clean up and remove trash.
(g) Place the Owner’s Manual and Warranty
Card, sealed in its protective bag, in the
glove box.
Issue: B
10/24/07
Page 20 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
TVIP V5
RS3200 PLUS
Accessory Function Checks
Procedure
1
Look for:
Press and release the remote control lock
button to start the system’s arming process.
The turn signal lights flash once
All doors lock.
The security LED lights up.
2
Wait 30 seconds.
Security LED starts flashing; the system is now
armed.
3
Press and release the remote control’s unlock
button to disarm the system.
The turn signal lights flash twice.
The driver’s door unlocks.
The Security LED flashing.
Open the driver’s door, insert the key into the ignition switch and turn it to "ON". Roll down all the
windows, remove the key and exit the vehicle.
4
Arm and disarm the system with the remote
again, then wait 60 seconds.
The doors automatically relock.
5
Press and release the remote control’s unlock
button again to stop the arming process.
Refer to step 3.
6
Insert the key into the driver’s door key
cylinder and turn it toward the front of the
vehicle to start the arming process.
All doors lock.
The Security LED lights up.
7
Wait 30 seconds.
Security LED starts flashing; the system is now
armed.
8
Reach inside and manually unlock the driver’s
door to trigger an alarm.
The driver’s door automatically relocks.
The system automatically starts the arming
process.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The Security LED lights up.
9
Manually unlock the driver’s door again and
hold it unlocked, open the door, then sit in the
driver’s seat.
The driver’s door lock attempts to lock
repeatedly.
The horn continues to sound repeatedly.
The headlights and turn signal lights continue
flashing.
The Security LED remains on.
10
Press and release the remote control’s unlock
button to disarm the system.
The horn stops sounding.
All the lights stop flashing and/or turn off.
The LED turns off.
The turn signal lights flash twice.
The drivers door unlocks.
Issue: B
10/24/07
Page 21 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
11
TVIP V5
RS3200PLUS
With the door open, press the lock switch on
the door to lock the doors, then close the door
to start the system’s arming process.
All doors lock.
12
Wait 30 seconds.
Security LED starts flashing; the system is now
armed.
13
Reach inside and manually unlock the front
passenger’s door to trigger an alarm.
The front passenger’s door automatically
relocks.
The Security LED lights up.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The Security LED lights up.
14
Press and release the remote control’s unlock
button to stop the alarm.
The horn stops sounding.
All the lights stop flashing.
The LED flashing.
15
Press and release the remote control’s lock
button to start the system’s arming process,
then wait 30 seconds until the system is
armed.
Refer to steps 1 and 2.
16
Unlock and open one of the rear passenger
doors to trigger an alarm. (if available).
Refer to step 13.
17
Press and release the remote control’s unlock
button to stop the alarm.
Refer to Step 14
18
Repeat the above steps with the other rear
passenger door. (if available).
Refer to steps 1, 2, and 13.
Roll up all windows, remove the key and exit the vehicle.
20
Press and release the remote control’s lock
button to start the arming process.
Refer to step 1.
21
Wait 30 seconds.
After 30 seconds, the Security LED starts
flashing; the system is now armed.
Issue: B
10/24/07
Page 22 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
TVIP V5
RS3200PLUS
Perform the following check in a temperature-controlled environment.
(50°-90° F)
22
With the tip of a key, or Striker Tool pulled all
the way out (PPO only), tap the center of the
driver’s door window to trigger the alarm.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The Security LED lights up.
23
Insert the key into the driver’s door key
cylinder and turn it toward the back of the
vehicle to stop the alarm.
Refer to step 10.
NOTE: If the alarm does not trigger during functional verifications, increase the GBS sensitivity to the next
setting.
NOTE: If you do not disarm the system, the alarm will last 20 seconds. It is not necessary to check the
alarm duration.
Issue: B
10/24/07
Page 23 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
TVIP V5
RS3200PLUS
Vehicle Function Check
Function
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
Issue: B
Function
□
Head Light
High Beams
Turn Signal Lights
Tail Lights
Stop Lights
Backup Lights
Hazard Lights
Marker Lights
Dome/Courtesy Lights
Panel/Switch Illumination
Accessory Controls/Illumination
(if equipped)
Key Sensor Buzzer
Fog Lights (if equipped)
Daytime Running Lights (if equipped)
Trunk/Tailgate/Bed Lights (if equipped)
Glove Box Light (if equipped)
Cruise Control Light (if equipped)
Seat Belt Warning Light
If the warning light remains on, it may
indicate a system malfunction.
Air Bag Warning Light
If the warning light remains on, it may
indicate a system malfunction.
10/24/07
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
ABS Light (if equipped)
If the warning light remains on, it may indicate
a system malfunction.
Rear Wiper/Washer (if equipped)
Clock (if equipped)
Accessory Power Socket (if equipped)
Starter
Audio/Video (if equipped)
Power Sliding Door (if equipped)
Convenience Memory Settings (if equipped)
Heated Seats (if equipped)
Massage Seats (if equipped)
Rear Window Defogger (if equipped)
Power Side Mirrors (if equipped)
Side Mirror Defogger (if equipped)
Front Windshield Defogger (if equipped)
Navigation System (if equipped)
Rear Sunshade (if equipped)
Steering Wheel Audio Control (if equipped)
Steering Wheel Column Adjusts Without
Interference
Lamp Failure Sensor
If the warning light remains on, it may indicate a
system malfunction.
Page 24 of 25 pages
TOYOTA
FJ CRUISER
2008 -
Procedure
Function
□
□
□
□
□
□
□
Function
Track/Skid Control Light (if equipped)
If the warning light remains on, it may
indicate a system malfunction.
HVAC
Power Locks (if equipped)
Power Windows (if equipped)
Power Seats (if equipped)
Horn
Gauges
□
Front Wiper/Washer
□
□
□
□
□
□
Hood Latch Release
Passenger Air Bag Switch (if equipped)
Rollover Side Curtain Air Bag Switch (RSCA)
(if equipped)
Remove the short pin after Function Check.
Check with your port/dealer to find out if this step is needed.
Store Short Pin Here
Issue: B
TVIP V5
RS3200PLUS
10/24/07
Page 25 of 25 pages