KEY CUTTING MACHINE Operating manual

Transcription

KEY CUTTING MACHINE
Operating manual
D418562XA
USA
(c) 2000 ILCO UNICAN CORP., Rocky Mount, North Carolina
This manual has been prepared by ILCO UNICAN CORP. Rocky Mount, North Carolina
All rights reserved. No part of this publication may be reproduced or used in any form or by any means
(photocopying, microfilm or other) without the written permission of ILCO UNICAN CORP.
1st edition: November 2000
Printed in U.S.A.
INDEX
REFERENCE GUIDE ............................................................................................ 1
GENERAL .............................................................................................................. 2
1
MACHINE DESCRIPTION ......................................................................................3
1.1
2
3
SAFETY .........................................................................................................4
1.3
MAIN WORKING PARTS ...................................................................................5
1.4
TECHNICAL DATA ..........................................................................................6
1.5
ACCESSORIES PROVIDED ...............................................................................7
TRANSPORT ..........................................................................................................8
2.1
PACKING .......................................................................................................8
2.2
UNPACKING ...................................................................................................9
2.3
MACHINE HANDLING .......................................................................................9
MACHINE INSTALLATION AND PREPARATION ................................................10
3.1
4
5
MAIN CHARACTERISTICS ................................................................................3
1.2
CHECKING FOR DAMAGE ..............................................................................10
3.2
ENVIRONMENTAL CONDITIONS ......................................................................10
3.3
POSITIONING AND INSTALLATION ...................................................................10
3.4
DESCRIPTION OF WORK STATION ..................................................................11
3.5
GRAPHICS ...................................................................................................11
“SET UP” AND USE OF THE MACHINE ..............................................................12
4.1
KEYBOARD AND FUNCTIONS .........................................................................12
4.2
USE OF THE VISE JAW ..................................................................................13
4.3
CUTTING BY ELECTRIC CONTACT ..................................................................15
4.4
FITTING THE VISE JAW TO THE MACHINE .......................................................16
4.5
CUTTER ......................................................................................................16
4.6
CHANGING THE CUTTER ...............................................................................16
4.7
INVERTING THE PULLEYS ..............................................................................17
OPERATING GUIDE .............................................................................................18
5.1
INITIAL OPERATIONS .....................................................................................18
5.2
[0] COPY FROM AN ORIGINAL ......................................................................19
5.3
[1] CUT BY CARD .......................................................................................21
5.4
[2] CUT BY CODE .......................................................................................26
5.5
USE OF THE MACHINE WITH A PERSONAL COMPUTER ...................................28
5.3.1
5.5.1
5.5.2
5.6
[3] QUEUE FROM PC ............................................................................. 28
KEY DECODING ................................................................................. 28
[4] CALIBRATIONS .......................................................................................30
5.6.1
5.6.2
5.6.3
5.6.4
5.7
SPECIAL CASES ..................................................................................... 22
CALIBRATING THE V100 VISE JAW .......................................................... 30
CALIBRATING THE R100 JAW ................................................................. 33
CALIBRATING CUTTERS ........................................................................... 35
MANUAL ADJUSTMENTS .......................................................................... 36
[5] MAINTENANCE ......................................................................................37
5.7.1
5.7.2
TESTS ................................................................................................... 37
MACHINE ZERO POINTS .......................................................................... 39
5.8
OPTIONS [6] ................................................................................................42
5.9
ERROR MESSAGES ......................................................................................46
6
CLEANING ............................................................................................................48
7
MAINTENANCE ....................................................................................................49
7.1
TROUBLE SHOOTING ....................................................................................49
7.2
MAINTENANCE OPERATIONS .........................................................................51
7.3
CUTTER REPLACEMENT ................................................................................51
7.4
BELT REPLACEMENT AND TENSION ADJUSTMENT ...........................................52
7.5
CHECKING AND/OR REPLACING FUSES ..........................................................53
7.6
ELECTRONIC CIRCUIT BOARD REPLACEMENT .................................................54
7.7
KEYBOARD/DISPLAY REPLACEMENT ..............................................................55
7.8
ACCESS TO BACK COMPARTMENT .................................................................56
7.9
ACCESS TO BOTTOM COMPARTMENT ............................................................56
7.10
SENSOR REPLACEMENT ...............................................................................57
7.11
WIN-TRANSFER PROGRAM ...................................................................... 59
8
DISPOSING OF MACHINE ................................................................................... 60
9
ASSISTANCE ........................................................................................................60
9.1
HOW TO REQUEST SERVICE .........................................................................60
Operating manual - English
ULTRACODE
REFERENCE GUIDE
This manual has been produced to serve as a guide for users of the ULTRACODE electronic key-cutting
machine. Read it carefully; it is essential if you wish to operate your machine safely and effectively.
Contact Ilco Unican Technical Assistance for further information at 1-800-ILCO-USA / 1-800-452-6872.
Ext.: 200, 384, 356
CONTENTS
The contents of the manual are divided into sections relating to:
• Machine description ......................................................................................Chapter
• Transport and installation .............................................................................Chapters
• Calibration and use .......................................................................................Chapters
• Maintenance .................................................................................................Chapters
1
2-3
4-5-6
7-8-9
TECHNICAL TERMS
Common technical terms are used in this manual.
To assist those with little experience of keys and key-cutting, below is an illustration of the terms most
frequently used.
1
1
3
2
6
5
3
4
6
4
Fig. 1
1)
2)
3)
4)
5)
6)
Head
Blade
Shoulder
Tip
Back
Cuts
Copyright ILCO UNICAN CORPORATION 2000
1
ULTRACODE
GENERAL
USE
The ULTRACODE is designed for cutting keys of non-ferrous materials: brass, nickel silver, etc.
It must be installed and used according to the instructions indicated by the manufacturer.
If the key-cutting machine is used differently or for purposes different from those described in this manual,
the customer will forego any rights he may have over ILCO UNICAN CORP. Furthermore, unforeseen
danger to the operator or any third parties may arise from incorrect use of the machine.
INCORRECT USE
Improper use of this machine or failure of the operator to observe the instructions written in this manual will
void all guarantees and responsibilities of the manufacturer.
It is therefore essential to carefully read and understand this operating manual.
IMPROPER USE OF ELECTRIC CONTACT
CAUTION:
• it is not recommended to cut ULTRALITE™ anodized aluminium keys. It is also not recommended to
cut plastic keys or any keys with materials that do not have electrical conductivity.
MACHINE IDENTIFICATION
•
The machine is provided with an identification label which includes the machine’s serial number (fig. 2).
SILCA SpA - Via Podgora 20 (Z.I.)
31029 VITTORIO VENETO (TV) ITALY
®
manufacturer’s
address
%(0438) 9136
Telefax (0438) 913800
Telex 410579 SILCA I
type of
machine
TIPO
TYPE
N˚ MATRICOLA
SERIAL No.
working
voltage
VOLT
serial No.
Hz.
A.
WATT
absorbed
current
year of
manufacture
absorbed power
working
frequency
Fig. 2
2
1
ULTRACODE
MACHINE DESCRIPTION
The ULTRACODE is an electronic machine operating on two axes with controlled movement. The machine
was designed to add a high degree of cutting precision to operating speed and ease of use.
The ULTRACODE can be used in 2 different ways:
• entering the key code directly by means of the machine keyboard
• linking to a PC
Fig. 3
1.1
MAIN CHARACTERISTICS
• Movements
Movement of the two axes (X-Y) operates on ball screws activated by step motors, on rectified roller guides.
• Jaw
Standard four-sided vise jaw, specially designed to grip most commercial, automotive and residential keys.
• Cutter
Consists of a cutter in HSS (high speed steel), that is easily replaced.
Operator can adjust the cutter for the type of work and speed rotation needed.
An Optional carbide cutter is available.
• Display
Rear-illuminated and placed on the front of the machine.
Display with 4 rows of 20 characters each.
3
ULTRACODE
1.2
SAFETY
• Emergency stop
The red emergency button (N) (fig. 4, page 5) located on the right-hand side of the machine is used to stop
the Ultracode immediately in the event of faulty operation or danger to the operator.
When the cause of the emergency has been eliminated, turn the button 45˚ clockwise to deactivate it. The
button will “pop” out away from the machine when deactivated.
NOTE: the operator is responsible for keeping the area around the button clear so that it can be reached as
quickly as possible.
• Cutter motor protection
The cutter motor is protected against overheating by a cut-out switch (located inside the motor) .The motor
will automatically shut down if it reaches a certain temperature.
If the switch activates:
1) turn the machine off and disconnect the power supply cable. Machine will reset after motor has cooled
sufficiently.
If machine does not reset: contact Ilco Technical Assistance at 1-800-ILCO-USA
1-800-334-1381/ 1-800-452-6872
• Protective shield (optional)
The transparent protective shield is designed to cover the working parts as completely as possible,
ensuring operator safety.
4
1.3
ULTRACODE
MAIN WORKING PARTS
W
E
X
I
H
D
F
V
C
B
Q
S
T
R
N
Fig. 4
A - master switch
B - keyboard
C - display
D - vise jaw (V100)
E - clamp knob
F - key gauge
H - cutter
I - cutter shield
N - emergency button
Q - serial port
R - Y axis connector
S - X axis carriage
T - Y axis carriage
V - chip tray
W - optical reader
X - reader vise jaw (R100)
A
5
ULTRACODE
1.4
TECHNICAL DATA
Electricity supply:
110V-60Hz
(100V - 50/60Hz)
Maximum absorbed power:
110V: 3,6 Amp. 396 Watt
cutter motor:
one speed, single phase
cutter:
HSS (high speed steel) - optional hard metal carbide cutter - Part No. D405933ZZ
Tool speed:
•
60Hz: 1100 rpm (+/- 10%)
with pulleys inverted:
•
60Hz: 2700 rpm (+/- 10%)
Movement:
on 2 axes with ball screws activated by step motors, on rectified roller guides.
Jaw:
universal 4 sided vise jaw to grip flat, commercial, residential and automotive keys
Runs:
X axis: 2.24 “
Y axis: 1.26 “
Dimensions:
width: 19.69 “
depth: 19.69 “
height: 16.54 “ (with raised shield 25.59 “)
Mass:
81.4 lbs • 37 kg
Noise level:
sound pressure Lp(A) = 85 dB(A) (cutting steel keys)
6
1.5
ULTRACODE
ACCESSORIES PROVIDED
The ULTRACODE comes with a set of accessories for its operation and maintenance (tools, hex
wrenches, fuses) supplied in a special tool kit comprising:
tool kit
0.157 “ allen key
D300224ZZ
Z1 template
(regulating disk)
D416657BA
Tip stop with notch
D402301BA
0.196 “ allen key
D300225ZZ
Z2 template
(regulating block)
D416660BA
Tip stop
D402302BA
0.236 “ allen key
D300226ZZ
Z3 template
(regulating key)
D416658LR
Cutter release rod
D400754BA
2 Amp fuse – delayed
D312423ZZ
Z4 serial test connector
D416661ZZ
0.511” spanner
D302788ZZ
4 Amp fuse – rapid
D301185ZZ
Belt tension plate
D416552BA
D202443ZZ
0.39 “ spanner
D300308ZZ
10 Amp fuse - delayed
D316568ZZ
Anti-tilting device
D508699ZZ
0.059 “ allen key
D302434ZZ
4 Amp fuse - delayed
D308726ZZ
Slanted
brush
D306935ZZ
0.0787 “ allen key
D300221ZZ
6.3 Amp fuse - delayed
D310652ZZ
ø 0.0669 “ steel pin
D401225ZZ
0.0984 “ allen key
D300222ZZ
0.748 “ socket wrench
D306963ZZ
ø 0.0472 “ steel pin
D401224ZZ
0.118 “ allen key
D300223ZZ
WIN-TRANSFER program disk
7
ULTRACODE
2
TRANSPORT
The key-cutting machine is easily transported and is not dangerous to handle.
The packed machine should be carried by at least two people.
2.1
PACKING
The packing for ULTRACODE is designed to ensure safe transportation and to protect the machine and all
its parts.
a
3
Fig. 5
3
Keep dry
Handle with care
This side up
Use no hooks
Do Not Stack
To prevent any damage to the machine it is advisable to save the box for future transportation.
8
2.2
ULTRACODE
UNPACKING
After removing the machine from the packing box, check the contents in the box, which should comprise
the following :
1 ULTRACODE key-cutting machine
1 set of documents, including: an operating manual, a spare parts list and a *warranty card
1 power supply cable
1 tool kit
NOTE: we strongly recommend you keep the packing intact for future transportation.
2.3
MACHINE HANDLING
When the ULTRACODE has been unpacked, place it directly on its workbench; this operation should be
carried out by at least two people.
Carefully lift the machine firmly holding the base, and no other part. Do not drag the machine, the feet will
be bent and damaged.
ATTENTION:
never lift the machine by holding the keyboard stand (fig. 6).
INCORRECT!
CORRECT!
Fig. 6
-
*Warranty Card should be filled out and returned to Ilco Unican for tracking purposes.
9
ULTRACODE
3
MACHINE INSTALLATION AND PREPARATION
The key-cutting machine can be installed by the machine owner and does not require any special skills.
It is supplied ready for use and does not need any special set up. ( However, it is recommended that the
operator follows the calibration procedure before operating the machine.)
3.1
CHECKING FOR DAMAGE
The ULTRACODE is solid and compact and will not normally damage if transport, unpacking and
installation have all been carried out according to the instructions in this manual. However, it is always
advisable to check that the machine has not suffered any damage.
3.2
ENVIRONMENTAL CONDITIONS
To ensure that the best use is made of the key-cutting machine, it is important to place it in a well-aired
area which is not too damp.
The ideal conditions for the machine are:
temperature between 10˚C (50˚F) to 40˚C (104˚F) relative humidity: approx. 60%.
3.3
POSITIONING AND INSTALLATION
1) Place the machine on a horizontal surface, solid enough to support the weight of 75,9 lbs.
- to work with ease, we suggest that the workbench be approximately the height of the operator’s
hip.
- it is important to leave clearance of at least 12” behind the machine and on each side to ensure
proper ventilation.
2) Ensure that the machines voltage is the same as that of the mains power supply, which must be
properly grounded and provided with a differential switch.
- connect the power supply cable to the power supply socket.
12.00 inch
12.00 inch
1 12.00 inch
Power Supply & Power Switch
39.37 inch
Fig. 7
10
3.4
ULTRACODE
DESCRIPTION OF WORK STATION
The machine needs only one operator, who has the following controls at his/her disposal (fig. 4, page 5):
• master switch located on the back of the machine
• vise jaw
• keyboard
• display
• emergency button
3.5
GRAPHICS
•
The machine carries an adhesive warning label (fig. 8). These labels must never be removed.
Do not use compressed air
for cleaning
The use of protective
goggles is recommended
Fig. 8
11
ULTRACODE
4
“SET UP” AND USE OF THE MACHINE
4.1
KEYBOARD AND FUNCTIONS
The machine’s keyboard has 19 alphanumeric and 6 function keys.
The alphanumeric keys are used for entering the data card number and the cutting data (numbers and/or
letters) according to the code on the card in use.
Each of the 19 alphanumeric keys contains two characters: the main character (black) which is directly
active, and an alternate character (red), which can be activated by simultaneously pressing the SHIFT key.
E.g.:
pressed directly produces: 1
SHIFT
Pressed simultaneously produce: H
+
1
display
6
H
M
2
7
I
N
A
R
STOP
START
?
ENTER
CLEAR
COPY
SHIFT
W
function keys
3
8
O
B
S
E
J
X
4
9
P
C
T
F
K
Y
0
L
Q
D
U
G
5
V
Z
alphanumeric keys
Fig. 9
FUNCTION KEYS
STOP
Stop button, used particularly when the machine is in motion.
Stops the function in progress at any time in the operation.
START
Starts the machines operations
?
Returns curser to the last operation.
ENTER
Activation of various functions in the menu.
CLEAR
COPY
CLEAR: deletes numerical characters.
SHIFT
Pressed in combination with all the keys of the same color to enter the number or letter available.
• regulating the display
It is possible to adjust the angle of vision on the machine’s display by following the instructions described
below:
• To incline the angle of the display towards the bottom you must press the
key and then press the
key, simultaneously keeping them both pressed
up until you reach the desired angle for
veiwing..
• to incline the visualization of the display towards the top you must press the
key and then press
the
key, simultaneously keeping them both pressed
up until you reach the desired angle
for veiwing.
12
4.2
ULTRACODE
USE OF THE VISE JAW
white
V100 Vise Jaw
Fig. 10
The four-sided vise jaw ensures an excellent grip on the keys placed on their back or profile sides (fig. 11).
• Single Sided Keys cut by code should be positioned mainly on the A and/or B side of the clamp.
D side
Asymetrical
Automotive Keys
Ex.: Volkswagen®
4
3
2
D
4
1
3
B
A
2
1
3
2
4
3
2
Fig. 11
1
4
C
A side
C side
Standard
Cylindrical Keys
Symmetrical
Double Sided Keys
Index on groove
Ex.: Schlage®, Kwikset®
& Weiser®
Ex.: GM®, Toyota®, & Nissan®
B side Narrow Style Double Sided Keys
Ex.: Ford® & Mazda®
6
4
3
2
1
1
2
A
3
1
3
2
4
2
3
1
4
C
2
1
3
4
0
4
-
For keys to be cut by
code the side of the vise
jaw on which to place the
key is shown on the machines display.
To fit keys with tip stops,
place the tip stop bar provided into the special
grooves (fig. 12).
1
-
Fig. 12 - key stops
13
ULTRACODE
ATTENTION:
when closing the vise jaw, do not apply excessive pressure to
the knob. Turning the knob approximately 70˚ (equal to a
force of 3NxM) is sufficient to secure the key (fig. 13).
1
1
2
A
3
4
3
C
2
2
3
4
4
Fig. 13
3
2
4
NOTE: before starting the cutting process the V100 vise jaw key gauge will automatically fall to its rest position.
USING THE PINS
For keys with narrow blades the pins must be placed
between the bottom of the vise jaw and the back of the key
so that the key protrudes sufficiently out of the clamp and
therefore can be properly cut.
If the key has a narrow blade and is also very thin, 2 pins
must be used (see fig. 14).
Fig. 14
14
4.3
ULTRACODE
CUTTING BY ELECTRIC CONTACT
The ULTRACODE key-cutting machine is equipped with a low voltage electrical contact device which
permits the cutter to measure the key blank width as it approaches the cutter during the cutting phase (fig.
15).
Fig. 15
This exclusive feature permits the operator to secure the key to the most appropriate side of the 4 faced
vise jaw (A, B, C or D) therefore improving the grip on the key and eliminating the need for pins and/or
adaptors.
With the electrical contact feature, depth calibration is automatically calculated when the cutter touches the
keys profile during the cutting process.
Electrical contact is guaranteed for keys in steel, brass, nickel silver, Zamak or iron (with or without nickelplating).
Improper use of electric contact
•
it is not recommended to cut ultralite anodized aluminium keys. It is also not recommended to cut plastic
keys or any keys with material that does not have electrical conductivity by means of electric contact.
Attention: for these types of materials, use standard cutting.
•
cuts cannot be repeated on the same side of the key when electric contact cutting is used.
All data cards provided by ILCO are in the machine’s memory. The cards are enabled or disabled for code
cutting by electric contact at ILCO’s discretion.
The data cards are divided into 3 types which are distinguished by special symbols shown on the display
(asterisk “*” and “+” ).
Side - 1
Jaw: 100/A
Cutter: U01
Pieces = 3
Pos.: 0
Adapt.: 0
[START]
2) Vise Jaw: 100/B
START+
• data card with standard cutting (press START)
• alternative: electric contact cutting press SHIFT+START
Side - 1
Jaw: 100/B
Cutter: U01
Pieces = 3
Pos.: 0
Adapt.: 0
[START] +
3)
Vise Jaw: 100/*
START+
• data card with electric contact cutting (press START)
• alternative: standard cutting press SHIFT+START
Side - 1
Jaw : 100/*
Cutter: U01
Pieces = 3
Pos.: 0
Adapt.: 0
[START] +
1)
Vise Jaw: 100/A
START
• data card with standard cutting (press START)
A - B: indicate the side of the vise jaw
+ : indicates the alternative activated with the SHIFT+START keys
* : indicates that the key can be clamped to any side of the vise jaw when the data card is enabled for electric contact.
Operating keys:
SHIFT+START: changes the cutting procedure (‘standard’ or ‘by electric contact’) and starts cutting.
START: begins the cutting process.
ATTENTION:
the alternative selected with the SHIFT+START keys (‘standard’ or ‘by electric contact’) is maintained as long
as the chosen data card is in use. When the procedure has been selected, simply press START for
successive cutting operations.
15
ULTRACODE
4.4
FITTING THE VISE JAW TO THE MACHINE
To remove the vise jaw unit:
-
loosen the grub screw (D2) (fig. 16) and slide the vise jaw out of the dovetail guide.
To install the vise jaw unit on the machine:
-
slide the vise jaw into the dovetail guide, pushing it all the way in, then secure it by tightening the grub
screw (D2).
These instructions refer exclusively to the standard vise jaw (V100). For the use of optional jaws please
refer to the instructions provided along with them.
D2
Fig. 16
4.5
CUTTER
The majority of keys utilize the standard cutter (U01) for code cutting. In certain cases, special keys with
particular type cuts will require different cutters.
To change the cutter see chapter 4.6.
4.6
CHANGING THE CUTTER
1) remove the cutter protective shield (1) by loosening the screw (1a).
2) slide the cutter release rod (2) into the hole located on the left side of the machines cutter shaft chassis
(fig. 17).
3) loosen the cutter locking nut (4) by turning it clockwise with the19 mm socket wrench (3) provided with
the machine.
ATTENTION:
the thread is left-handed. (reversed)
4) replace the cutter, then tighten the nut (4) by turning it counter-clockwise and remove the rod from its
hole.
5) place the cutters protective shield (1) back into position securing it with the screw (1a).
1a
2
4
1
3
Fig. 17
WARNING: when replacing a worn cutter with a new one or with a re-sharpened cutter consult Ch.5.6.3 "Calibrating cutters",
page 35.
16
4.7
ULTRACODE
INVERTING THE PULLEYS
This operation must be carried out when the operator intends to use a carbide cutter (optional), in order to
adapt the cutter speed to the newcutter’s material.
W
Fig. 18
1)
2)
3)
4)
5)
6)
7)
8)
9)
turn the machine off and disconnect the power supply cable.
remove the back and bottom metal panel (ch.7.8 and ch.7.9, page 56).
loosen the 4 motor locking screws (W) (fig. 18) and remove the belt.
loosen the 2 grub screws securing the pulley and remove it from the motor shaft.
fit the cutter shaft locking rod and use the allen key provided to loosen the screw (A1) and grub screws
(A2) on the pulley (fig. 19).
invert the pulleys and secure them by tightening the grub screws, fit the screw and washer on the cutter
shaft.
remount the belt and adjust its tension (ch. 7.4, page 52).
remount the back and bottom metal panel.
enter the ‘cutter material’ function in Ch.5.8 "Options [6]", page 42, and alter the speed.
cutter shaft
A2
A1
motor shaft
for HSS cutter
for carbide cutter
Fig. 19
17
ULTRACODE
5
OPERATING GUIDE
Introduction
The Operating Guide below explains how to use the ULTRACODE without a Personal Computer.
All operations to manually use the key-cutting machine are explained step by step.
The programs available for Personal Computers connected to the key-cutting machine are able to
transmit data for cutting.
Programs for Personal Computers eliminate manual procedures of certain functions. Once the data
has been transmitted to the machine it by passes some of the operating guide screens.
When the ULTRACODE is used with a Personal Computer, the operating guide does not change its
display logic, except for screens that are rendered unnecessary.
5.1
INITIAL OPERATIONS
When the key-cutting machine has been placed on its workbench and connected to a power source
(Ch.3.3, page 10), proceed as follows:
1) make sure that the emergency button is not turned on.
2) turn the machine on by means of the main switch that is located on the back of the machine.
3) to check or alter the parameters for use of the machine, consult the "Options [6]" menu (ch.5.8,
page 42).
When the machine is turned on, for a few
seconds the display shows the internal
software version and the machine model:
MAIN MENU
Operational keys:
use the
keys to move the cursor to the option required
and press ENTER or directly press the numbered key
corresponding to the option number.
The >> symbol indicates that the menu contains other items
which can be reached with the arrow key
.
* APPEAR ONLY WHEN AN OPTIONAL
OPTICAL READER IS INSTALLED &
ACTIVATED
18
ULTRACODE
version 1.0.0
0 - Copy from original *
1 - Cut by card
2 - Cut by code
3 - Queue from PC
>>
4 - Calibrations
5 - Maintenance
6 - Options
>>
5.2
ULTRACODE
[0] COPY FROM AN ORIGINAL
ONLY- WITH THE OPTICAL READER -(OPTIONAL)
1) select the function.
Operational keys:
0 - Copy from original
1 - Cut by card
2 - Cut by code
3 - Queue from PC
use the arrow keys
to move the cursor to the option required and press ENTER or directly press the numbered key
2) insert the original key into the R100 optical
reader side jaw.
Jaw = R100/?
According to the type of key to be copied, establish
which side of the jaw the key must be inserted. Enter ‘?’ (A, B, C or D) in the jaw sides field (Ch.4.2,
ENTER
Original on right
Jaw=R100/_?
(ABCD)
Pos. = 0
(0-4)
Dist. = 000
[START]
START
page 13).
Pos. = 0
Key gauge stop; by default the program always
shows the ‘0’ stop (Ch.4.2, page 13).
For keys without a shoulder stop, enter the tip stop
position (1, 2, 3, 4).
READING IN PROGRESS
Dist.= 000
To be used only for keys without a shoulder stop
(from 0 to 0.393 inch).
To insert the “Dist.” (distance) you must first enter
the “Pos.” (stop position) from 1 to 4.
The entered “Pos.” (stop position) cannot be stop
“0” (“Pos.” must be 1, 2 , 3 or 4).
Example: with tip stop ‘2’ the cuts must start to be
read at least 2 mm/.079” before the normal starting
position (stop “0”).
0
4
3
2
A
1
4
Fig. 20
Operational keys:
numerical keys to enter the distance in the “Dist.” field.
SHIFT+ arrow key
: chooses the jaw from those available
for the reading unit (with ‘R’ prefix); the jaw sides and stop are
automatically set up. Important: the last reading jaw setting remains until another one is selected.
3) Place the key to be cut in the ‘V100’ cutter
side jaw.
ATTENTION:
use the same side and stop position as the key fitted to
the R100 optical reader side jaw.
- during the reading process the key is
partially cut; it will be completed only
at the end of the reading process.
19
ULTRACODE
•
Adjustments ?
Depth = +00
Spaces = +00
[START]
Data alteration
The operator may alter the ‘depth’ and ‘space’
parameters.
Operational keys:
to increase or decrease the parameters use a combination
of the SHIFT +
or SHIFT +
.
Depth: (from -38.9 to + 38.9 thousandths of a inch.)
Enter the figure (positive or negative) to raise or lower all the cuts.
Example:
Adjustments ?
Depth = -0,03
Spaces = - 0,02
[START]
-
+
Fig. 21: depth adjustments
START
Key blank on left
Jaw= 100/A
(ABCD)
Pos.: = 0
Dist.: -000
Pieces = 3
[START]
START
Spaces: (from -38.9 to + 38.9 thousandths of a inch)
Enter the figure (positive or negative) to move all the
cuts closer to or farther from the key stop.
-
+
CUTTING IN PROGRESS
Copy: 1 of: 3
Copy :1 of: 3
Finished.
More copies?
No = STOP
Yes = ENTER
Fig. 22: spaces adjustments
Pieces:
enter the number required.
4) Carry out the same procedure to cut the
remaining keys.
20
5.3
ULTRACODE
[1] CUT BY CARD
One part of the machine’s memory is used for the data cards.
A data card is a database of cutting spaces, depths and angles for all the keys in the machines data base.
The number of data cards is increased periodically when the ULTRACODE is updated. The updates are
easily installed to a P.C. then transmitted over to the machine.
ILCO data card ( 1 ):
This option allows you to enter an Ilco Card Number
(Example: 567 GM). This data card comprises the
‘spaces and depths’ database as described in
the introduction to Ch.5 "OPERATING GUIDE",
page 18).
Enter card number:
1 - ILCO = 567
2 - HPC =
3 - USER =
The source of this information can be the ILCO Card
listing, catalogues and other available documents.
HPC data card ( 2 ):
This option allows you to enter an HPC equivalent
card (Example: CF215 GM).
ENTER
Side 1 x 2
..........
Possible depths:
1234
ILCO 567
USER data card ( 3 ):
This option is a user defined card.
DESIGN A KEY FEATURE
See Supplement to accompany the Update Disk.
1) Press ENTER
ENTER
Vise Jaw: V100/*
The special symbol (asterisk) means that the cuts
will be made by electric contact (Ch.4.3, page 15)
therefore it is unnecessary to select the vise jaw
side.
Pos.: 0
Place the key to be cut into the V100 vise jaw using
the stop that is shown.
Cutter: U01
Recommended cutter.
Pieces:
enter the quantity of keys to be cut.
2) proceed with cutting the first side by pressing
the START key.
3) turn the key over and cut the second side.
Operating keys:
SHIFT+START: changes the cutting procedure (‘standard’ or
‘by electric contact’) and starts cutting.
START: begins the cutting operation.
SHIFT+ arrow key
selects the side of the key to be cut.
Side: 1
Jaw.: 100/*
Cutter: U01 STD
Pieces = 2
Pos. : 0
[START]+
START
CUTTING IN PROGRESS
Copy: 1 of: 2
Side 1
Side: 2
Jaw: 100/*
Cutter: U01
Pos. : 0
[START]+
START
CUTTING IN PROGRESS
Copy: 1 of: 2
Side 2
- when the last side of the last key has
been cut, the screen shows:
START
Copy: 2 of: 2
finished.
More copies?
No = STOP
Yes = ENTER
21
ULTRACODE
5.3.1
SPECIAL CASES
•
Cutting a key with two asymmetrical sides
Enter card number
1 - ILCO = 115
2 - HPC =
3 - USER =
Operational keys:
use the
arrow keys to be able to visualize both sides of
the keys possible cuts on the machines display.
ENTER
Side 1
.....
Possible depths:
4321
ILCO 115
1112213331
ENTER
Side 2
.....
Possible depths:
4321
ILCO 115
1121123313
ENTER
Proceed with the cutting process.
•
Side: 1
Jaw : 100/A
Cutter: U01 STD
Pieces = 1
Pos. : 0
[START]
Impossible cutting combination
When the machine is used manually with certain data cards, it may not be possible to carry out certain
entered combinations. This happens when the cutting depths are not compatible in the order the user
entered the possible cuts.
Example:
Enter card number
1 - ILCO = 174
2 - HPC =
3 - USER =
ENTER
Side 1
.....
Possible depths:
012345678
ILCO 174
08213
ENTER
non-feasible
combination!
22
ULTRACODE
The reason for the conflict between certain
cuts is explained simply in the case shown.
With regard to the cut that originated the
message <non-feasible function> it can be seen
that between the two deep cuts (8) and the
constant angle (100˚) the intermediate cut (0)
would be removed.
This happens when the cutting angle N (Normal)
is not made variable by means of the type of cut
L (Laser) (page 24).
8
?
0
α
8 4
α
α
6
α
Fig. 23
The new drawing is an example of how with the
same cuts (80846), the cutting angles are
automatically calculated by the conjunction of
the cutting base with a straight line.
This aspect, admissible with certain car keys, is
more commonly known as ‘the ideal cutting line’.
ATTENTION:
in this example it can be seen that the ß angle
is less than 45˚. This could cause serious
problems with a lock, making it difficult or
impossible to place the key into the cylinder or
remove it.
8
α β
0
8 4 6
β
γ δ
α
Fig. 24
23
ULTRACODE
•
Types of cut
All the data cards provided by Silca have the type of cut pre-set according to the original parameters.
The types of cut possible with ULTRACODE are: Radius, Normal, Flat, Laser and Vertical.
N
NORMAL
For conventional car and door keys.
P
FLAT
Mainly used for car keys where the cut edges are
rounded to facilitate the movement of the blades when
the key is put into the lock.
R
RADIUS
This type of cut eliminates flats and creates a radius at the
bottom of each cut.
L
LASER
Cuts with variable angles can be obtained, peaks are
eliminated, giving the advantage of key copies that slide
perfectly into the lock.
V
VERTICAL
Primarily used for flat steel or safety deposit keys.
V
EXAMPLE OF HOW TO CHANGE THE TYPE OF CUT:
All the technical data regarding the types of
cuts stored in the machine’s memory can be
changed according to the user’s requirements.
Enter card number:
1 - ILCO = 567
2 - HPC =
3 - USER =
1) enter data card number (e.g.: nr.567)
2) before entering the cuts press
combination of keys SHIFT+ENTER.
ENTER
the
3) enter the “L” type cut by pressing the
SHIFT+L keys to set the laser type cut.
- the letter in brackets (L) indicates the
type of cut recommended by Ilco.
NOTE: for certain cutting methods the standard
cutter U01 must be replaced with a specific
cutter (Ch.4.6 "Changing the cutter", page
Side 1 x 2
..........
Possible depths:
1234
SHIFT
+ ENTER
ILCO 567
Cutter: U01
Cut type (L) = L
Alternative : N P
16).
ENTER
4) enter the combination and proceed with the
operations described in ch.5.3, page 21.
24
ILCO 567
Side 1 x 2
112233
Possible depths:
1234
ILCO 567
•
ULTRACODE
Changing the cutter/adaptor/jaw
Some of the data cards stored in the machine’s memory require a different cutter / adaptor / jaw from the
standard or the previous installed.
EXAMPLE
:
Enter card number:
1 - ILCO =
2 - HPC =
3 - USER =
ENTER
Side 1
ILCO
.. . . . .
Possible depths:
and / or
ENTER
ATTENTION !!
Install cutter:
#
ENTER
Is cutter:
#
installed?
No = STOP
Yes = Enter
and / or ENTER
ATTENTION !!
Install Jaw:
#
ENTER
Is Jaw:
#
installed?
No = STOP Yes =Enter
and / or ENTER
ATTENTION !!
Install adaptor:
#
ENTER
Is adaptor:
#
installed?
No = STOP Yes =Enter
25
ULTRACODE
5.4
[2] CUT BY CODE
a) SEARCH BY CODE
CODE: AA11
MFG :
=>
(AA00-7T51 GM94+ GM)
ENTER
Side 1 x 2
1123321323
Possible depths:
1234
ILCO 567
ENTER
Side: 1
Jaw.: 100/*
Cutter: U01
Pieces = 2
Pos. : 0
[START]+
START
CUTTING IN PROGRESS
Copy: 1 of: 2
Side 1
Side: 2
Jaw: 100/*
Cutter: U01
Pos. : 0
[START]+
START
CUTTING IN PROGRESS
Copy: 1 of: 2
Side 2
START
Copy: 2 of: 2
finished.
More copies?
No = STOP
Yes = ENTER
26
ULTRACODE
b) SEARCH BY MANUFACTURER
Use the arrow
to move the
cursor to the following manufacturer.
CODE :
MFG : G
=> GM
(4) LIST
[ENTER]
ENTER
=> GM
01 :AA00-7T51 GM94+
02 :H1-H3988BGM2000
03 : O1-O6999 GM 2000
ENTER
Side 1 x 2
ILCO 567
Possible depths:
1234
ENTER
Side: 1
Jaw.: 100/*
Cutter: U01 STD
Pieces = 2
Pos. : 0
[START]+
START
CUTTING IN PROGRESS
Copy: 1 of: 2
Side 1
Side: 2
Jaw: 100/*
Pos. : 0
Cutter: U01 STD
[START]+
START
CUTTING IN PROGRESS
Copy: 1 of: 2
Side 2
START
Copy: 2 of: 2
finished.
More copies?
No = STOP
Yes = ENTER
27
ULTRACODE
USE OF THE MACHINE WITH A PERSONAL COMPUTER
5.5
In the previous pages, the ULTRACODE key-cutting machine operational instructions have been
presented from the point of view of manual use, i.e. operating from the keyboard incorporated in the
machine to cut keys by code.
The information transmitted by the Personal Computer cannot be altered manually. Each line transmitted
corresponds to a stage in the cutting process for one or more keys.
As described above, for each cutting process transmitted the number of pieces to be cut is set¸ a ‘+’ sign
shows when the cycle is finished.
The ‘+’ sign warns the operator that the last cutting operation has been carried out.
Should a work queue be interrupted, turn off the ULTRACODE . When the machine is turned on again and
the <PC queue> is called up, the list reappears, starting from the first line.
5.5.1
[3] QUEUE FROM PC
The data received from the PC are presented in one form only:
•
quantity of keys in queue transmitted
•
key code
•
card number
•
quantity of keys
•
the “+” mark indicates that all three keys (or
more) have been cut.
•
the “-” mark indicates that the total quantity
of keys referring to its code have not been
cut.
6 CODES RECEIVED
1+ AB100
[234] 3
2 - AB101
[234] 3
3 - AB102
[234] 3
4 - 2315
5 - 1251
6 - W109
....
Pressing the ENTER key takes us to the
‘Copying by code’ procedure. From this point
on the operational functions are the same as
those described in ch.5.3, page 21.
C.= data card from PC.
When the SHIFT + ENTER keys are pressed
additional data referring to the choosen code
can be visualized, such as:
• Customer’s name
• Key blank
Operational keys:
To quickly go to the next key to be cut, strike the
arrow key
. Doing so the operator starts from
where she or he stopped the previous operation.
arrow keys
: to scroll the lines.
[122] 5
[122] 5
[567] 5
ENTER
Side 1
1234
Possible depths:
1234
SHIFT
+ ENTER
BOB SMITH
ART. GT10P
SHIFT + arrow keys
: to scroll 4 lines at a time.
SHIFT+ENTER keys to show customer data and
key item linked to the selected code.
When the START key is pressed the cursor will
automatically position itself on the first key code that
indicates the “-” mark.
28
C. 234
5.5.2
ULTRACODE
KEY DECODING (ONLY IF OPTICAL READER INSTALLED)
The decoding function by means of the optical
reader can be activated only when using a PC.
After the decoding function is launched from the
program, the machine’s display shows the
following information:
Ilco 50: the data card used.
Decode
ILCO 50
ORIGINAL on right.
Jaw: 100/?
Pos.: 0
Side: 1
[START]
1) insert the key into the R100 optical reader’s
side jaw.
2) press START to begin the operation.
START
DECODING IN PROGRESS
Side 1
NOTE: if the key has 2 or more asymmetrical sides
the machine’s display will show the message
“waiting for computer data”. Each side of the
key to be decoded will appear:
Waiting for
computer data!
Decode
ILCO 50
ORIGINAL on right.
Jaw: 100/?
Pos.: 0
Side: 2
[START]
- the Software Program will then display
the cutting data decoded from the machine.
Decoding OK.
See computer.
ATTENTION:
if a key decoding/reading operation is started and
the diameter of the cutting tool exceeds 2.3779
inch (e.g. cutter 06 Ø 2.543 inch), the display will
show the following message:
ATTENTION !!
Install cutter:
01
Replace the cutter according to the instructions in
Ch.4.6 "Changing the cutter", page 16.
ENTER
Is cutter:
01
installed?
No = STOP
Yes = ENTER
29
ULTRACODE
5.6
[4] CALIBRATIONS
The following components on the machine have a specific ‘self-setting’ procedure with the use of regulating
templates (Ch.1.5 "Accessories provided", page 7).
- VISE JAW
- CUTTERS
ADAPTERS provided as options do not require calibrating. However, if necessary adjustments can be
made to the cutting data, according to the procedures described in Ch.5.6.4 "Manual adjustments", page
36.
In the circumstances listed below (see events) it may be necessary to re-set one or all of the jaws and/or
cutters that the user has in possession. This operation is semi-automatic and requires close attention to
the instructions listed below.
EVENT
MACHINE ZEROES
CALIBRATION (chap. , pag.30)
JAWS
Electronic board replacement
CUTTERS
YES
YES
YES
(see ch.7.6, page 54)
Replacement of sensors
YES
NO
NO
V100 vise jaw replacement
NO
YES
NO
(with a new one of the same type)
Replacement of the cutter shaft
YES
NO
NO
Re-sharpening of existing cutter
and/or cutter replacement
YES
NO
YES
YES
NO
Installation of optional jaws
NO
(if applicable)
Replacement of the ball screws
YES
1) Enter the ‘Calibrations’ menu #4.
Operational keys:
use the arrow keys
to move the cursor to the option required and press ENTER or directly press the numbered key
NO
NO
1 - Cut by card
2 - Cut by code
3 - Queue from PC
4 - Calibrations
>>
ENTER
2) Select ‘Jaws’ #1.
1 - Jaws
2 - Cutters
3 - Adaptors
ENTER
5.6.1
CALIBRATING THE V100 VISE JAW
Jaws
V100
V101
V102
Before starting the vise jaw calibration, make
sure that there are no keys and/or adapters fitted
in the V100 vise jaw.
Operational keys:
SHIFT+ENTER: to select and visualize each side of the vise
jaw (where applicable).
STOP: to exit the menu.
ENTER
V100
SIDE A
Adjustment: SIDE A
X = +00
Y = +00
To calibrate
[START]
START
30
ULTRACODE
3) replace the cutter with the (Z1) template (fig.
25). To remove the cutter follow the
instructions on page 16, ch. 4.6 "Changing
the cutter".
4) insert the (Z3) template to the side of the
V100 vise jaw that is shown on the machine’s
display.
5) press START.
V100
SIDE A
Install Z1 & Z3 temp.
See operating manual
[START]
START
V100
- this will automatically start the setting of
the V100 vise jaw by means of electric
contact between the two templates.
V100
SIDE A
X = +002
Y = +004
Save data?
No = STOP
Yes = ENTER
- the display shows the differences from
the theoretical values.
6) to save the data press ENTER.
ATTENTION:
SIDE A
Detection
in progress!
ENTER
if the STOP key is pressed, the new settings will
be lost. If so, only the previous setting values
will remain valid.
NOTE: the settings will be accepted only if the
tolerances remain within a range between
–11.8/+11.8 thousandths of a inch.
Exceeded setting
tolerance limit.
See operating manual.
- if the tolerances exceed the accepted
range the machine’s display will show
an error message:
- carefully follow the instructions and
repeat the procedure.
ENTER
Z1
Z1
Z3
Z3
Fig. 25
31
ULTRACODE
•
- the operational sequence will continue
and the display will show the settings
for sides B, C and D.
turn the V100 vise jaw to side B, insert the
(Z3) template into the vise jaw and proceed
with the settings, following the same
procedure described for side A.
•
turn the V100 vise jaw to side C, insert the
ATTENTION:
make sure that the (Z3) template is properly
inserted into side C of the V100 vise jaw (see
fig. 26).
•
turn the V100 vise jaw to side D, insert the
ATTENTION:
inserted into side D of the V100 vise jaw (see
fig. 26).
V100
SIDE B
Adjustment SIDE B
X = +00
Y = +00
To calibrate
[START]
V100
SIDE C
Adjustment SIDE C
X = +00
Y = +00
To calibrate
[START]
V100
SIDE D
Adjustment SIDE D
X = +00
Y = +00
To calibrate
[START]
Operational keys:
use the arrow keys
to directly select the side of the vise
jaw you intend to set.
START: to begin the setting procedure.
STOP: to interrupt the setting procedure.
ATTENTION:
-
after calibrating all sides of the V100 vise jaw:
remove the (Z3) template from the V100 vise
jaw.
remove the (Z1) template from the cutter
shaft replacing it with a cutter.
Z3
side C
Z3
side D
Fig. 26
32
5.6.2
ULTRACODE
CALIBRATING THE R100 JAW ( ONLY IF INSTALLED )
- OPTICAL READER Before starting the jaw setting, make sure that
there is no key and/or adapter fitted in the V100
cutter side jaw.
1) enter the ‘Options’ menu and select option 1
– ‘Jaws’.
1 - Jaws
2 - Cutters
3 - Adaptors
ENTER
5 - R100
ENTER
The >> symbol indicates that the selected jaw has
more than one side.
Operational keys:
SHIFT+ENTER: to select and visualize each side of the jaw
(where applicable).
STOP: to exit the menu.
R100
Adjustment SIDE A
>>
X = +00
Y = +00
To calibrate
[START]
START
2) fit the (Z3) template to side A of jaw R100
(fig. 27).
ATTENTION:
lower the key gauge.
R100
Install the Z3 template.
[START]
3) press START to proceed with automatic
setting of side A.
- during this operation the settings are
read by the optical reader.
START
R100
SIDE A
Detection
in progress!
R100
SIDE A
X = +023
Y = +009
Save data?
No = STOP
Yes = ENTER
4) press ENTER to save data.
ATTENTION:
ENTER
will remain valid.
NOTE: the settings will be accepted only if the
tolerances remain within a range between
–11.8/+11.8 thousandths of a inch.
an error message:
- carefully follow the instructions and
repeat the procedure.
Exceeded setting
tolerance limit.
ENTER
33
ULTRACODE
•
•
- the operational sequence will continue
and the display will show the settings
for sides B, C, D.
turn the R100 jaw to side B, insert the (Z3)
template into the jaw and proceed with the
settings, following the same procedure
described for side A
turn the R100 clamp to side C, insert the (Z3)
ATTENTION:
inserted into side C of the R100 jaw (fig. 26).
•
turn the R100 jaw to side D, insert the (Z3)
ATTENTION:
inserted into side D of the R100 jaw (fig. 26).
R100
SIDE B
Adjustment SIDE B
X = +00
Y = +00
To calibrate
[START]
R100
SIDE C
Adjustment SIDE C
X = +00
Y = +00
To calibrate
[START]
R100
SIDE D
Adjustment SIDE D
X = +00
Y = +00
To calibrate
[START]
R100 Jaw
Z3
Fig. 27
34
5.6.3
ULTRACODE
CALIBRATING CUTTERS
For this procedure always use side A of the V100
vise jaw.
According to the cutter speed (determined by
fitting the pulleys in the way described in ch.4.7,
page 17) and material (chosen from the ‘Options
– cutter material’ menu on page 42) the list will
show all the HSS or carbide cutters
(distinguished by the suffix ‘W’).
1 - Jaws
2 - Cutters
3 - Adaptors
ENTER
1) enter the “cutters” menu #2.
Cutters
Operational keys:
use the arrow keys
to move the cursor to select the
required cutter and press ENTER.
2) fit the selected cutter to the machine.
00 - U01
01 - 01
02 - 02
ENTER
00 - U01
Adjustment:
Y = +00
To calibrate
[START]
START
3) fit a brand new (Z3) template on side A of the
V100 vise jaw and press START.
00 - U01
Install the Z3 template.
[START]
START
00 - U01
Detection
in progress!
- the display shows the differences from
the theoretical values.
NOTE: the setting will be accepted only if the
tolerance of the cutter’s diameter remains
within a range between +39.3 /–39.3
thousandths of a inch.
00 - U01
Adjustment: +002
Save data?
No = Stop
Yes = ENTER
ENTER
an error message:
- carefully follow the instructions and repeat the procedure
ATTENTION:
Once this operation is completed the (Z3)
template must be thrown away; contact with the
cutter, skims the surface of the template, these
marks would cause errors if used for future
settings.
Exceeded setting
tolerance limit
ENTER
35
ULTRACODE
5.6.4
MANUAL ADJUSTMENTS
(JAWS – CUTTERS - ADAPTERS)
The operator may carry out manual adjustments by entering new X and Y parameter values.
ATTENTION:
such adjustments should be made only when the automatic setting has already been carried out (where
applicable).
Adjustments can be made within a range
between +11.8 and –11.8 thousandths of a inch.
To adjust jaws and adapters, the positive values
of X will give the result shown in fig. 28.
-
+
1 - Cut by card
2 - Cut by code
3 - Queue from PC
4 - Calibrations
>>
ENTER
1 - Jaws
2 - Cutters
3 - Adaptors
Fig. 28
For adjustments to cutters, clamps and adapters,
the positive values of Y will give the result shown
in fig. 29.
+
-
ENTER
JAWS
V100
Adjustment SIDE A
>>
X = +00
Y = +00
To calibrate
[START]
Fig. 29
The >> symbol indicates that the selected clamp has more than
one side.
Operational keys:
place the cursor next to the parameter and enter the adjustment
figure using the SHIFT + arrow keys
.
CLEAR: to zero out adjustments
ENTER or down arrow key
: to move the cursor from the X
to the Y axis settings
ENTER: press in the final entry field to quit the menu.
STOP: to exit the menu
SHIFT+ENTER: to go from one side of the clamp to another
when making manual adjustments.
ATTENTION:
ENTER
STOP
Cutters
00 - U01
Adjustments:
Y = +00
To calibrate
ENTER
[START]
STOP
Adaptors
B1
Adjustments:
X = +00
will remain valid
ENTER
Y = +00
STOP
Save adjustments ?
No = STOP
Yes = ENTER
Press START only if you
intend to proceed with
automatic calibration.
36
5.7
ULTRACODE
[5] MAINTENANCE
1) enter the ‘Maintenance’ menu #5.
5 - Maintenance
6 - Options
Operational keys:
use the
and press ENTER or directly press the numbered key corresponding to the option number.
5.7.1
ENTER
TESTS
There is an on board TEST menu that should be
used to verify the cause of any breakdown that
may occur to the machine.
•
1 - Test
2 - Machine ‘0’ point
Test 0: OPTICAL READER (Only if installed)
Carefully follow the instructions that are on the machine’s display. Check that the optical reader’s
status changes from OFF to ON.
NOTE: if the OFF/ON transition is not made, contact Ilco Technical Support.
•
Test 1: X AXIS MOTOR
Carefully follow the instructions on the machine’s display. Check that the X axis carriage moves.
ATTENTION:
during this test function all end of run controls are disactivated; avoid moving the carriage up against its
mechanical stops.
NOTE: if the motor does not start, contact Ilco Technical Support.
•
Test 2: Y AXIS MOTOR
Carefully follow the instructions on the machine’s display. Check that the Y axis carriage moves.
ATTENTION:
during this test function all end of run controls are disactivated; avoid moving the carriage up against its
mechanical stops.
NOTE: if the motor does not start, contact Ilco Technical Support.
•
Test 3: CUTTER MOTOR
Carefully follow the instructions on the machine’s display. Check that the cutter motor is working.
NOTE: if the cutter motor does not turn, contact Ilco Technical Support.
•
Test 4: X AXIS SENSOR
-
the machine’s display should show ON when the carriage is drawn away from the machine (towards the operator).
the machine’s display should show OFF when the carriage is pushed all the way in towards the
machine.
-
NOTE: if the ON/OFF transition is not made, contact Ilco Technical Support.
•
Test 5: Y AXIS SENSOR
-
the machine’s display should show OFF when the carriage is moved all the way to the right.
the machine’s display should show ON when the carriage is moved all the way to the left (towards
the cutter).
37
ULTRACODE
•
Test 6: ELECTRIC CONTACT
Use any metal conductor to contact jaw to cutter, checking that the machine’s display indicates OFF
to ON.
•
Test 7: KEYBOARD
One at a time, press all the keys (except STOP) checking that an asterisk (*) appears for each key pressed.
Press the STOP key for last.
NOTE: if the asterisk does not appear, contact Ilco Technical Support.
•
Test 8: DISPLAY
All points on the display should be obscured.
NOTE: if this is not so, contact Ilco Technical Support.
•
Test 9: SERIAL PORT
Check that the machine’s display indicates OFF.
Fit the special (Z4) serial test connector (accessories provided) to the machine’s serial port, checking
that the machine’s display indicates OFF to ON.
38
5.7.2
ULTRACODE
MACHINE ZERO POINTS
With the use of regulating templates (Ch.1.5 "Accessories provided", page 7) the machine provides a ‘selfsetting’ procedure.
EVENT
MACHINE ZEROES
CALIBRATION (chap. , pag.30)
JAWS
Electronic board replacement
EVENT
CUTTERS
YES
YES
YES
Replacement of sensors
YES
NO
NO
Replacement
sensors
V100 vise jaw replacement
NO
YES
NO
V100 vise jaw
replacement
Electronic board
replacement
of
(with a new one of the
same type)
Replacement of the cutter shaft
YES
NO
NO
Replacement of
the cutter shaft
Re-sharpening of existing cutter
and/or cutter replacement
YES
NO
YES
Re-sharpening of
existing
cutter
and/or
cutter
replacement
(with a new one of the
same type)
Installation of optional jaws
NO
YES
NO
(if applicable)
Installation
optional jaws
of
.
READING UNIT
Operational keys:
use the
keys to move the cursor to the option required and press
ENTER or directly press the numbered key corresponding to the option
number.
Procedure:
enter the “Maintenance” #5.
select “Machine zero points” #2.
select “Reading unit’ #2
remove R100 clamp (optical reader side) from its
support.
5) install the (Z2) template, the clamp’s bushing and
secure them with the clamp’s knob (fig. 39).
1)
2)
3)
4)
-
the ‘machine’s zero’ setting are
detected by the optical reader.
-
when this operation is completed, the
machine’s display will show the
measured quotes
ATTENTION:
if the STOP key is pressed, the new setting will be lost. If
so, only the previous setting values will remain valid.
5 - Maintenance
6 - Options
1 - Test
2 - Machine ‘0’ point
ENTER
Install Z1 & Z2
templates.
ENTER
Move X and Y axis
up until contact is made
START
TEMPLATE E R R O R
No contact made.
39
ULTRACODE
jaw’s knob
jaw’s bushing
X
Z1
Z2
Z2
Z2
Z1
top view
Fig. 30
Regulating the Y axis sensor:
• use the provided allen key to loosen the (C1)
grub screw; manually rotate the (C2) rod (fig.
31) in both directions up until the changeover
point from OFF to ON is found.
• tighten the (C1) grub screw (fig. 31) to
secure the rod.
START
Pos. sensors.
ICX = OFF
ICY = OFF
[START]
Pos. sensors.
ICX = OFF
ICY = ON
[START]
Regulating the X axis sensor:
• carefully tip the machine over.
• remove the bottom panel by unscrewing all 8
securing screws.
• loosen the (C3) screw (fig. 32, page 41) that
secures the sensor support plate. Manually
move the sensor support plate up until the
display’s description goes from OFF to ON.
• tighten the (C3) screw (fig. 32, page 41) to
secure the plate back into place.
• re-position the machine back on its
workbench.
• press START.
- the ‘machine’s zero’ settings are detected by electric contact.
6) when the operation has been completed,
the display will show the measured quotes.
7) press ENTER to save the settings.
ATTENTION:
will remain valid.
Pos. sensors.
ICX = OFF
ICY = OFF
[START]
Pos. sensors.
ICX = ON
ICY = ON
[START]
START
Zero detection
in progress!
Measured quotes:
X = 4444
Y = 3333
Save measurements?
No = STOP
Yes = ENTER
ENTER
40
Y
ULTRACODE
Y axis sensor
C1
C2
C2
Fig. 31
C3
bottom view
ATTENTION: if it is necessary
to work close to this area with
the machine turned on (e.g. to
regulate the X axis sensor)
take great care not to touch
any
components
on
the
machine’s electronic boards
as it is connected to 230 /110
Volts.
Fig. 32
X axis sensor
C3
Fig. 33
41
ULTRACODE
5.8
OPTIONS [6]
1) Enter ‘Options’ menu # 6.
Operational keys:
use the
and press ENTER or directly press the numbered key corresponding to the option number.
5 - Maintenance
6 - Options
ENTER
1 - Serial No.
2 - Optical Reader
3 - Cutter material
4 - Cutting speed
>>
5 - Carriage speed
6 - Preference
7 - Language
8 - Inversion keyboard
>>
9 - Min. distance
10-Modify keys stop
1 - SERIAL NUMBER:
displays the machine’s serial number that should
correspond to the Serial Number that is stamped
on the back of the machine.
Model :
Ser. n: 153214523123
Model : UltraCode
Keys cut : _ _ _
SW Version : _._._
type of Ultracode.
Keys cut :
numbers of keys cut.
SW Version :
Software version of the program installed on the
machine.
2 - OPTICAL READER
Set by Ilco Technical Assistance
Opt.Reader installed = 0
( 0 = NO
1 = YES )
Speed = 350
(100-350)
3 - CUTTER MATERIAL:
The option ‘cutter material’ shows all the HSS
(enter 0) or carbide (enter 1) cutters.
By inverting the two pulleys two cutter rotation
speeds can be obtained:
• low speed for HSS cutters
• high speed for hard metal carbide cutters
Inversion of the pulleys gives the first or second
speed according to the method described in
Ch.4.7, page 17.
42
Cutter Material = 0
(0 = HSS
)
(1 = Hard metal )
ULTRACODE
4 - CUTTING SPEED:
Corresponds to the carriage advancement
speed during the key cutting operation:
On the basis of the cutter material selected,
speed can be altered as shown in the table.
Cutting speed
HSS
Hd. Met.
300
400
(100-400)
(200-700)
cutter metal
Recommended
speed
Speed Range
HSS
300
100-400
Hard metal
400
200-700
carbide
5 - CARRIAGE APPROACH SPEED:
This is the speed at which the carriages move
towards the cutting area, before starting the
cutting cycle.
We recommend to operate the machine with the
speed that is set (4000). If required, the operator
can adjust the carriage approach speed from a
minimum of 1000 to a maximum of 5000.
Carriage approach
speed = 4000
(1000 - 5000)
6 - PREFERENCES:
work parameters are chosen from this menu.
Inches or millimetres:
choose the measurements you intend to work
with (mm = millimetres, inch. = inches).
Start-up menu:
choose the function in the Main menu that you
would like to appear first when the machine is
turned on:
*
1
2
3
4
= Main menu
= Cut by card
= Cut by code
= Queue from PC
= Calibrations
Attention: press the “CLEAR/COPY” key to void
any selection made and to select the (*) main
menu function.
Prefered MFG:
1-Measurement Unit
2-Start Menu (*)
3-Prefered MFG
Measurement Unit =
( INCH = 1 )
( Millimetres = 0 )
e.g. when ‘0’ is set, the display shows the following
when the machine is turned on:
Menu selection
0-Copy from original
1-Cut by card
2-Cut by code
3-Queue from PC
MFG Selection :
0- All MFG
1-* ALFA ROMEO
2- BMW
3-* CADILLAC
4- DODGE
43
ULTRACODE
7 - LANGUAGE:
enter the number that corresponds to the
language you intend to work with.
8 - KEYBOARD INVERSION
This function inverts the alphanumerical
keyboard (numbers to letters (fig. 9, page 12).
With “Inversion keyboard” disactivated (0) :
• to digit number 1: press 1
Select language = 2
1 : English
2 : Français
3 : Español
Inversion keyboard
function = 0
(1 - enabled)
see Operating manual
H
•
to digit the letter H: press SHIFT +
1
H
With “Inversion keyboard” enabled (1) :
• to digit number 1: press SHIFT + 1 H
•
to digit the letter H: press
1
H
NOTE: this function can be carried out from the main menu“ Cut by card” and/or “Cut by code”
9 - MINIMUM DISTANCE:
The number shown on the machine’s display
represents the X axis distance between the key blank
shoulder and the beginning of the first cut (fig. 34).
This function is extremely important with keys that
require cuts on both, sides as it ensures precise
positioning on the keys 2nd side.
Min. distance
of cut from key stop = .197
(0 - 3.89)
Fig. 34
The set figure is 19.7 thousandths of a inch, which can
be varied between min.0 - max. 38.9 thousandths of a
inch.
ATTENTION:
44
settings that are too high may render precise cuts
impossible, with the following message on the
display:
Min. Parameter of
DISTANCE FROM STOP
is incompatible with
selected card!
ULTRACODE
10 - MODIFY KEYS STOP:
Normally the machine does not require key
shoulder stop adjustment.
If required, it is possible to modify the key’s
shoulder according to the modification made to
the key shoulder (fig. 35).
If the operation is to be confirmed, the X and Y
figures are both required:
Modify key stop
Enabled = 0
(0-1)
Thickness X =
0
Height Y
= .118
X thickness:
measurement of the shoulder stop to be cut is
expressed in hundredths of a inch (min.0 max.3.89).
x
Y height:
height of the shoulder read on the key using a
calliper, expressed in hundredths of a mm. E.g.:
• X = 0.197 inch = 19.7 thousandths
• Y = 0.118 inch = 11.8 thousandths
y
Fig. 35
45
ULTRACODE
5.9
46
ERROR MESSAGES
Data card not
compatible with
jaw installed!
•
The selected data card is for a different jaw
from the one installed on the machine. Install
proper jaw.
•
The entered data card number is not
available in the machine’s data base.
•
The entered cuts cannot be carried out (see
Ch.5.3.1, page 22)
•
This message appears when the cutter
must be changed with one that is
compatible to the type of cuts required for
the entered data card number.
•
This jaw is not available in the machine’s
data base.
Jaw not
available!
•
This cutter is not available in the machine’s
data base.
Cutter not
available!
•
This adapter is not available in the
machine’s data base.
Adaptor not
available!
•
The entered data card number requires a
type of cut that is not available in the
machine’s data base.
Type of cut
not available!
•
The minimum distance from the key stop
position overlaps the first cut on the key
(Ch.5.8, page 42).
MIN. Parameter of
DISTANCE FROM STOP
is incompatible with
selected card!
•
This message appears when the cutter is
unable to identify the keys measurements
when cutting by means of electric contact.
POSITION ERROR
Key not
properly installed!
Data card
not available!
Non-feasible
combination!
ATTENTION !!
Install cutter:
U01
ULTRACODE
•
During the cutting cycle one or more depth
exceeded the maximum limit. These depths
are automatically aligned to the maximum
permitted depth.
•
The automatic setting revealed a variation
that exceeded the permitted nominal figure
setting reference. Carefully repeat the
setting procedure.
Exceeded setting
tolerance limit
•
During the setting of the “machine’s zero
points” there is a contact failure between the
two templates (see ch.5.7.2, page 39).
TEMPLATE ERROR
no contact made.
•
Indicates that the entered function is not yet
available.
ATTENTION
Depth limit
exceeded!
Non-feasible
function !
The electronic control board has exceeded
the maximum permitted temperature. Check
the cooling fan (ch. 7.1 "Trouble shooting",
page 49).
TEMPERATURE ALARM
•
Indicates that the fuse has blown due to a
short circuit in an inlet or outlet (ch. 7.1
"Trouble shooting", page 49).
I/O POWER ALARM
Check fuse F4 !
•
Indicates a short circuit in port P (IN/OUT)
(ch. 7.1 "Trouble shooting", page 49).
DIGITAL OUTLET
PROTECTION ALARM
Turn the machine off !
•
Indicates that the fuse has probably blown
(ch. 7.1 "Trouble shooting", page 49).
CUTTER MOTOR
ALARM
Check fuse F1 !
•
Indicates a fault on the electronic control
board.
•
Turn the machine off!
CUTTER MOTOR
ALARM
Fault on motor circuit !
47
ULTRACODE
6
CLEANING
•
•
•
48
keep the operational parts of the machine as clean as possible by brushing away the chippings in areas
where they accumulate during cutting operations.
under no circumstances must compressed air be used to clear the work zone of chippings as this will
blow them onto the moving parts.
Never use oily products or thinners for cleaning painted surfaces, jaws, electrical or electronic
connections.
7
ULTRACODE
MAINTENANCE
Although the ULTRACODE key-cutting machine does not require special maintenance, it is advisable to
check and, if necessary, replace the parts subject to wear and electric/electronic parts (fuses, circuit
boards, etc.) in the event of faulty operation.
Replacement is simple and can be carried out by the operator consulting the instructions.
Before starting any type of maintenance (controls or replacements), read the instructions below:
• never carry out maintenance with the machine switched on
• always remove the main power supply cable
• strictly follow all the instructions in the manual
• use original spare parts (see Spare Parts sheet provided).
7.1
TROUBLE SHOOTING
FAULT
PROBABLE CAUSE
Machine is on, with no
message on its display.
check to see if the back fan is working
not working:
a) emergency button activated
b) general fuses in the power socket are faulty
working:
a) fuse F3 on electronic control board is faulty
b) connection wire between display and electronic circuit board loose
c) defective display
cutter motor
working.
not
a) the F1 fuse on the electronic control board is faulty
b) motor wire not properly attached to the connector
c) defective electronic control board
d) motor cut-off
WARNING: this may derive from inappropriate or heavy use of the key-cutting machine or a
fault with the motor itself. DO NOT USE THE MACHINE and call Ilco Technical Dept. to
determing the cause of activation of the cut-off.
X, Y and B axes motors
are not working.
None of
motors
working:
the
a) fuse F2 on the electronic control board faulty
b) the wiring between the transformer and electronic control board is
loose or the connector is not seated properly.
c) defective electronic control board
Only
one
motor is not
working:
Keyboard not working
(partially or completely)
a) the connection wires between the motor and the electronic control
board are loose or the connector is not seated properly
b) defective electronic control board
a) the keyboard connector is not properly connected to the interface board (fig. 36)
b) the wiring between the keyboard/display unit and electronic control board is not properly
attached to the relative connectors
c) defective keyboard
d) defective electronic control board
Electric contact not
working
(during
calibrating or cutting).
a) wiring between the J14 connector on the electronic control board and cutter shaft is loose
or disconnected
b) wiring inside the Y axis carriage is not seated properly or disconnected
c) brass shavings on cutter shaft behind cutter
49
ULTRACODE
FAULT
PROBABLE CAUSE
Key-cutting machine fails
to communicate with
computer.
a) wiring between 9-pin serial port and electronic circuit board not seated properly or disconnected
b) serial cable between key-cutting machine and computer is faulty
c) computer serial port is not functional
The display shows the
message
‘TEMPERATURE
ALARM - Turn the
machine off’.
check that the fan on the back of the key-cutting machine is working:
not working
a) fan faulty
b) electronic control board faulty
working
electronic control board faulty
message: ‘I/O POWER
ALARM – check fuse F4’.
a) fuse F4 on the electronic control board faulty.
message:
‘DIGITAL
OUTLET
PROTECTION ALARM turn the machine off’.
internal fault on the electronic control board.
message:
‘CUTTER
MOTOR ALARM check fuse F1’.
a) fuse F1 on the electronic control board faulty.
50
b) short circuit on the inlets. To find which inlet is causing the error message, disconnect the
J7-8-14-20 connectors one at a time and check each time whether the alarm disappears.
b) cutter motor wiring disconnected.
c) internal fault on the electronic control board.
7.2
MAINTENANCE OPERATIONS
•
•
•
•
•
•
•
•
•
7.3
ULTRACODE
Cutter replacement
Belt replacement and tension adjustment
Fuse check and replacement
Electronic circuit board replacement
Keyboard/display replacement
Access to back compartment
Access to bottom compartment
Sensor replacement
WIN-TRANSFER program for loading/updating the machine program
CUTTER REPLACEMENT
1) turn the machine off and unplug it.
2) remove the cutter protective shield (1) by loosening the screw (1a).
3) slide the cutter release rod (2) into the hole located on the left side of the machines cutter shaft chassis
(fig. 36).
4) loosen the cutter locking nut (4) by turning it clockwise with the19 mm socket wrench (3) provided with
the machine.
ATTENTION:
the thread is left-handed (reversed).
5) replace the cutter, then tighten the nut (4) by turning it counter-clockwise and remove the rod from its
hole.
6) place the cutters protective shield (1) back into position securing it with the screw (1a).
1a
2
4
1
3
Fig. 36
WARNING: when replacing a worn cutter with a new one or with a re-sharpened cutter consult Ch. "", page 29.
51
ULTRACODE
7.4
BELT REPLACEMENT AND TENSION ADJUSTMENT
To replace the belt, proceed as follows:
1)
2)
3)
4)
5)
6)
7)
turn the machine off and unplug it.
remove the back panel (Ch.7.8, page 56).
remove the bottom panel (Ch.7.9, page 56).
loosen the 4 screws (W) securing the motor (fig. 37).
remove the worn belt from the pulleys.
fit the new belt onto the pulleys, making sure that the direction of rotation is correct.
using the provided belt tension plate and the (W2) screw (fig. 37) adjust the belt’s tension by turning
the (W2) screw.
8) tighten the 4 (W) (fig. 37) screws back into place, securing the motor.
9) remount the back and bottom panel.
W
W2
Fig. 37
W2
Fig. 38
To adjust belt tension proceed as follows:
1)
2)
3)
4)
turn the machine off and unplug it.
remove the bottom panel (Ch.7.9, page 56).
loosen the 4 screws (W) securing the motor (fig. 37).
using the provided belt tension plate and the (W2) screw (fig. 37) adjust the belt’s tension by turning
the (W2) screw.
5) tighten the 4 (W) (fig. 37) screws back into place, securing the motor.
6) remount the bottom panel.
52
7.5
ULTRACODE
CHECKING AND/OR REPLACING FUSES
Fuses should be checked with a tester (ohmmeter, multimeter, etc.) as they may appear to be in good
condition even when they are electrically faulty. Fuses must always be replaced with the same amperage
and type (rapid or delayed), as indicated in this manual.
There are 6 fuses in the ULTRACODE.
• 2 fuses: 6.3 Amps rapid
located next to the power socket on the back of
the machine, next to the main switch (fig. 39).
These fuses protect the machine from power
surges and/or spikes in the electricity supply.
To check and/or replace the fuses proceed as
follows:
1) turn the machine off and unplug it from its
power supply cable.
2) use a flat screwdriver to open the flap
covering the socket, remove and check the
fuses, replacing them if necessary.
Fig. 39
• 4 fuses: F1, F2, F3, F4
F1: 10 Amps delayed
- protects the cutter motor and its electronic controls
F2: 6,3 Amps delayed
- protects the step motors and their electronic controls (+32V d.c.)
F3: 4 Amps delayed
- protects the logic control circuits on the microprocessor board (+5V d.c.)
F4: 2 Amps delayed
- protects the digital output circuits for the low voltage controls and the sensor inlets (+24V d.c.)
Situated on the electronic circuit board inside the base of the machine (fig. 40) protecting the board from
short circuits.
To check and/or replace the fuses proceed as follows:
1) turn the machine off and unplug it from its power supply cable.
2) remove the bottom panel (Ch.7.9, page 56).
3) check and, if necessary, replace the fuses in the way described below:
to remove the fuse:
-
press the fuse cap with your fingers and turn it counter clockwise.
To fit the new fuse:
-
carefully position the fuse back into place, then gently press the fuse cap downwards turning it clockwise.
F1
to open fuse cap
F2
F3
F4
to close fuse cap
electronic circuit board
Fig. 40
53
ULTRACODE
7.6
ELECTRONIC CIRCUIT BOARD REPLACEMENT
If the board still communicates with the P.C. it is possible to save the data of the machine’s original settings
using the WIN-TRANSFER program disk that is provided along with the machine (see Ch.7.11, page 51).
- use the function ‘Save settings’.
- replace the electronic circuit board:
2) remove the bottom panel (Ch.7.9, page 56).
3) disconnect all cable connectors from the electronic circuit board (fig. 41).
electronic circuit board
Fig. 41
4) take the electronic circuit board off by unscrewing the (Y1)
nuts off (fig. 42).
5) mount the new electronic circuit board and re-connect all
cables (all cable connections are polarosed therefore
cannot be connected incorrectly).
6) re-fit the bottom panel and re-position the machine on its
workbench.
7) turn the machine on and launch the WIN-TRANSFER
program.
8) If the settings have been saved, launch the ‘Recover
settings’ function. If not, carry out the setting operations
(Ch.5.7.2 "Machine zero points", page 39 and Ch., page
29).
Y1
Fig. 42
54
7.7
ULTRACODE
KEYBOARD/DISPLAY REPLACEMENT
1)
2)
3)
4)
5)
turn the machine off and unplug it from its power supply cable.
remove the display’s support, by unscrewing the 3 (B1) fixing screws (fig. 43).
detach the flat cable and ground wire from the keyboard (fig. 44).
unscrew the keyboard’s fixing nuts and remove the keyboard from its support.
fit the new keyboard/display, repeating the operations described above, backwards.
Fig. 43
B1
Fig. 44
55
ULTRACODE
7.8
ACCESS TO BACK COMPARTMENT
To gain access to the back compartment, proceed as follows:
2) unscrew the 6 (M1) screws that secure the back panel (fig. 45) thus removing it.
M1
Fig. 45
7.9
ACCESS TO BOTTOM COMPARTMENT
To gain access to the bottom compartment, proceed as follows:
2) turn the machine on its back side.
3) remove the machine’s bottom panel by unscrewing the 8 (L1) screws.
L1
Fig. 46
56
7.10
ULTRACODE
SENSOR REPLACEMENT
X AXIS SENSOR REPLACEMENT
1)
2)
3)
4)
5)
6)
turn the machine off and unplug it from its power supply cable.
remove the bottom panel (chap.7.9 "Access to bottom compartment").
disconnect the X axis sensor’s connector from the electronic circuit board (fig. 47).
loosen the (L3) nut. Unscrew the sensor from the plate and remove it (fig. 48).
remove the front cover on the (X axis) lower carriage (fig. 49) by unscrewing the 3 (B4) screws.
fit the new sensor in position, tightening it until it almost touches the (L2) screw (fig. 48) thus securing
it with the (L3) nut.
7) connect the sensor’s connector to the electronic circuit board.
8) remount the bottom panel and front cover.
Fig. 47
X axis sensor
L2
0.0039 - 0.0157 inch
L3
Fig. 48
B4
Fig. 49
57
ULTRACODE
Y AXIS SENSOR REPLACEMENT
10) raise the protective shield.
11) disconnect the (J1) Y axis cable from the
carriage (fig. 50).
12) remove the Y axis carriage cover by
unscrewing the 3 (B5) locking screws and
pull the cover in the direction shown in fig.
50.
13) disconnect the (M3) sensor’s connector
(fig. 51).
14) slightly loosen the (M2) grub screw with
the provided allen key.
15) remove the faulty sensor and replace it
with a new one. Screw it in until it almost
touches the underlying rod (fig. 52).
Tighten the (M2) grub screw to lock the
sensor into place.
16) connect the (M3) sensor’s connector.
17) replace the Y axis carriage cover.
18) connect the (J1) Y axis connecting wire to
the carriage.
Fig. 50
M3
M2
Y axis sensor
Fig. 51
Y axis sensor
0.0039-0.0157 inch
Fig. 52
58
B5
J1
7.11
ULTRACODE
WIN-TRANSFER PROGRAM FOR LOADING/UPDATING THE INTERNAL MACHINE
PROGRAM.
The machine is supplied with an internal program already loaded and tested at Ilco Unican Corp. The user
therefore does not need to carry out any operations.
Only in the situations described below can the WIN-TRANSFER program be used to re-start the machine.
The following is a list of situations where the use of the WIN-TRANSFER program is required.
For further details on installation and use of the program, follow the instructions given on the instruction
sheet provided with the disk.
•
Replacement of the electronic board (see ch. 7.6, page 54) or loss of the internal machine
program.
1) replace the board with a new one, if necessary.
2) install on your personal computer the latest version received of the WinTransfer program and follow the
instructions given on the instruction sheet provided with the program.
3) read the serial number on the data plate on the back of the machine (ch.5.9, page 42) and enter on the
machine.
4) gauge the machine according to the instructions in the manual, as follows:
- gauge as explained in chapter 5.7.2 "Machine zero points" in the user’s manual.
- gauge the V100 vise jaw (ch. 5.6.1, page 30).
•
At this point the machine is set up and ready for operation
•
Loading of customized key data cards provided by ILCO on Customer’s request
59
ULTRACODE
8
DISPOSING OF MACHINE
To dispose the machine, it must be rendered unusable by carrying out the operations listed below:
• deactivation of the electricity supply;
• separation of the plastic and metal parts;
When these operations have been carried out, the machine can be disposed of according to the current
regulations in the country of use.
WASTE DISPOSAL
The ULTRACODE is made up of recyclable parts.
Recycling is ecologically recommended.
Packing
The packing in which the machine is transported is made of cardboard and wood therefore can be re-used
if intact or if dismantled used as combustible materials.
Warning! Take great care when dismantling the packing as it contains nails, which could cause injuries.
We recommend to bend the nails downwards into the box with a hammer or to completely remove the nails
disposing them in authorized metal recycling centres.
The packing is considered solid urban waste and must not be thrown into the environment but placed in
special cardboard collection bins.
Waste deriving from key cutting
The waste deriving from key cutting is classified special waste, but is still classified as solid urban waste,
as metal wool. Such waste must be disposed of in special collection centres according to the classification
assigned to them by the current EEC law. The circumstances which transform metal residue from solid
urban waste into contaminated or toxic noxious waste are listed in the appendices to the current European
Union regulations regarding disposal of such waste.
Waste is any substance or object deriving from human activity or natural cycles, disposed of or to be disposed of.
9
ASSISTANCE
Ilco provides full service to purchasers of the ULTRACODE key-cutting machine. To ensure complete
safety to the operator and machine, any job not specified in this manual should only be carried out by the
Ilco Technical Support.
It is our hope that this ULTRACODE Operating Manual will enable you to quickly and efficiently set up, and
begin using your new ULTRACODE key machine. For more detailed information, trouble shooting
practices, common maintenance tips, and useful photos, please contact Ilco Technical Assistance. We
strongly advise you to keep this document safe and readily available. It will prove very useful in the future.
Should you require addition assistance or support, please feel free to contact the IlcoTechnical Assistance
Dept.
Ilco Technical Assistance Dept.
400 Jeffreys Road
Rocky Mount, NC 27804
USA
Tel: 1-800-ILCO-USA
1-800-(452-6872) Ext: 200, 384, 356
Fax: 252-446-4702
9.1
HOW TO REQUEST SERVICE
The guarantee attached to the ULTRACODE ensures free repairs or replacements of faulty parts within 12
months of the date of purchase. For other services, please contact Ilco Technical Assistance Dept.
60
USA: 400 Jeffreys Road
Rocky Mount, NC 27802-2627
Telephone: 252-446-3321
Fax: 252-446-4702
Canada: 7301 Decarie Blvd
Montreal, Que. H4P 2G7
Telephone: 514-735-5411
Fax: 514-735-8707
www.ilcounican.com
D418562XA

KEY CUTTING MACHINE Operating manual

Transcription

Similar documents

Heart Attack Warning Signs

WAREHOUSE ThermoFlex xtra (nylon)

HEART ATTACK - KNOW THE SYMPTOMS Poster

projectnightnight bag toppers

Sizzix Catalogue July2010 - Adventist Church in UK and Ireland

How to Tie a Woggle

stump cutter - Vermeer Corporation

Key Machines Key Machines www.keyosk.co.uk

KEY MACHINES