The best just got better...Argo announces the

LT-7_Layout 2 8/3/15 9:38 AM Page 1
Lo-Trim II Accessories
A complete line of matching accessories designed for quick and easy snap-on installation. The
right piece for any job.
The best just got better... Argo announces the
standardization of galvanized steel across its
residential hydronic baseboard products.
End Caps
3" left or right
end caps that
extend to the
floor.
3 Piece Splice
2" Joining piece set,
7" Filler piece set,
14" Filler piece set.
Each set contains
3 pieces.
Outside Corners
available in 90°
and 135° angles.
2 7/8
[73]
Hinged Valve
Enclosure
left or right 4" end
caps extend to the
floor.
Inside Corners
available in 90°,
and 135° angles.
RESIDENTIAL
LO TRIM II
B A S E B OA R D
Wall Ends
Wall ends
available
in 3".
Single Element Lo-Trim II Hot Water Ratings BTU per hour per
linear foot of active (finned) length (with damper).
1 15/32
[37]
Through the use of a two phase state-of-the-art manufacturing process
Model GPM
LT 1/2"
4
1
4
1
Average Hot Water Temperaure - BTU/HR./LIN. FT.
120°F 130°F 140°F 150°F 160°F 170°F 180°F 190°F 200°F
215
204
209
198
269
255
262
248
328
311
319
302
390
370
380
360
450
430
440
420
520
490
510
480
590
560
570
540
670
630
630
600
740
700
710
670
Argo has taken the esthetically pleasing and clean-heat performance of
7 15/32
[190]
4 21/32
[118]
2 5/8
[67]
LT 3/4"
The use of Rating @ 4GPM is limited to installations where flow rate is
known to be equal to or greater than 4 GPM. If flow rate is unknown, use 1
GPM rating.
residential baseboards to unprecedented levels of durability.
1 19/32
[40]
Ratings include 15% addition to water heat capacity.
CAT-62839C
13/16
[21]
1 1/4
[32]
DIMENSIONS IN "[ ]" ARE SHOWN
IN MILLIMETERS.
Hot water ratings shown are at the STANDARD WATER FLOW RATE of 500 lb/hr
(1GPM) and 2,000 lbs/hr (4GPM) with 65º entering air temperature.
Friction loss through Argo Baseboard unit at 1 GPM (500 lbs/hr) is 47
MIL-INCHES per foot and at 4 GPM (2000 lbs/hr) is 525 MIL-INCHES PER FOOT.
Rating base on active length. Difference between active and total length is 3".
Aluminum fins are 2-1/8" x 2-1/8" x .008" thick, spaced 51 per foot (unpainted).
During phase one all critical components of the baseboard including
the vane, front and back plates are “hot-dipped” galvanized through an
ARGO BASEBOARD
260 North Elm Street • Westfield, MA 01085
Tel: (413) 564-5975 • Fax: (413) 572-3764
www.argobaseboard.com
LO-TRIM II BASEBOARD RADIATION
Providing comfort to any room with style!
environmentally friendly no-lead process increasing rust corrosion resistance
A MESTEK COMPANY
LT-7
• Low Profile
• Advanced Design
• Quiet Operation • Quick & Easy to Install
PT-6_Layout 2 8/3/15 9:26 AM Page 1
above that of traditional processes. Phase two incorporates a beautiful paint
finish process which further increases corrosion resistance and durability
providing users with a life-time solution to their hydronic heating needs.
COM M E RCIAL / R E S I DE NTIAL
Argo’s versatile hydronic heating products are the perfect solution for
all areas of the home including high moisture areas such as kitchens,
PANEL TRIM II
B A S E B OA R D
bathrooms and even basements.
HIGH OUTPUT
BASEBOARD RADIATION
260 North Elm Street | Westfield, MA 01085 | 413-568-9571
www.sterlingbaseboard.com
GLV-AR-1