durastrip - Targetti

Transcription

EN
DURASTRIP
I
Index
Colour, Ra and Qa: a better way to define colour!
02
“Custom made” DURASTRIP: how and why
06
DURASTRIP White Light IP20
09
13
DURASTRIP CTC: white variations
17
DURASTRIP RGB IP20, RGB+W (White) IP68
21
DURALUM
25
MOUNTING INSTRUCTIONS
28
PROFILES
30
DRIVERS, CONTROLLERS, DIMMERS
36
DURASTRIP WIRING DIAGRAMS
39
CODES TABLES
42
Cover photo:
The Lake Restaurant Saint-Petersburg
DURASTRIP shapes and bends light according to different needs.
Powerful emission and concise colour control are unique characteristics
of DURASTRIP. They meet all the demands of modern strips
specifications, flexibility, both indoor and outdoor unstallation, a very
long life, and extended maintenance cycles. The range of applications
for LED strips of this calibre is extensive and as is often said, the only
limit is your imagination. The following pages show what DURASTRIP
can do for you, exploring all potential options and installation.
Figure 4: CRI of an RGB+W (White) source Ra=83
Figure 5: CRI of an RGB+W (White) source Qa=95
Figure 6: CRI LED "A" Ra=92
Figure 7: CQS LED "A" Qa=85
2
Colour, Ra and Qa: a better way
to define colour!
Thanks to the increasing diffusion of LEDs and with the experience
acquired in using LEDs for lighting more attention is paid to the
quality of light colour. This means that while analysing the colour
rendering of white light there is always a difference between the
measured quality parameter, CRI (Color Rendering Index), and the
level of quality perceived by the human eye. As chip manufacturers
specialise in creating and perfecting increasingly efficient LED
lights, the difference between measured and perceived parameters
increases and it becomes more difficult to explain the divergence
between the rigid measurement parameters and the real effect
within the environment.
CRI is the result of the need to give parameters to “colour fidelity”
and is calculated for comparison with the source type as a
reference. Colour fidelity on its own is not an evaluation parameter
that can sufficiently identify the quality of white light: it does not take
into account any possible variations in colour saturation that can
improve visual ability to discriminate those colors. Light is a living
component of every element, each individual “perceives” colour
in a different way, in fact no two eyes are the same and colour
interpretation varies from individual to individual. Colour itself, its
perception, depends on a state of mind and can therefore be seen
in different ways and generate different sensations.
The new and yet un-standardised parameter to measure colour
Quality is the CQS (Color Quality Scale). Unlike the CRI it uses a
different method of calculation: it compares 15 saturated colours
evenly distributed in the colour space. The same colour space
used to measure is no longer the CIE1931, used for CRI, but the
CIELAB: it allows for more accurate measurement because it is a
more complete color model used to describe all colours visible to
the human eye.
A multiplicative factor has also been introduced, a function of
colour temperature, to take into account reduced colour rendering
that characterises extreme colour temperatures.
Figure 1: CIE LAB Diagram
Figure 2: C.I.E. 1931 Diagram
Figure 3: Difference between the palettes of comparison of sources
The CRI works suitably with broad spectrum sources while the
CQS is better suited to narrow spectrum sources with high peaks
and vast empty areas.
In the CQS the source being tested is not penalized by “points” for
any deviances from the reference if the deviance improves colour
saturation.
A good example of the above is a comparison between results
obtained by using the two methods on a RGB+W (White) source:
strongly penalized by the CRI system, if used adequately it has
appreciable results in real life applications.
The source is evaluated by the CRI system with a Ra=83 and with
the CQS system with a Qa=95, the real difference can be seen by
using a source of this type in applications where fabric or places
that have a lot of different colour tones are lit. See Figures 4 and 5.
In the same way a good LED source which we will call “A”, with a
spectral line that duly follows the CRI reference source, if evaluated
with the CQS does not perform so well, given that colours near to
BLUE are less saturated. See Figures 6 and 7.
In conclusion, the official reference parameters at present do
not express the potential of this particular technology, moreover
the same is in continuous evolution. It follows that the method to
evaluate a source must be an accurate analysis of its spectrum in
relation to what needs to be lit in order to manufacture a product
that can reproduce what we want to illuminate accurately and
without distorting colour tones.
3
PERCEPTION OF
COLOURS: THE PERFECT
SPECTRUM
Colours do not exist unless they are shown in a light that contains
them in its spectrum. The same colour is perceived in a totally
different way depending on the source that illuminates it. Not only
according to the colour temperature, the kind of source and its
colour rendering, but most of all according to the spectral distribution
of the source. DURALAMP is now able to offer exactly the spectrum
that the lighting designer wants, in order to exhibit the goods or
artworks of any environment at its best! We can recreate with LEDs
the same spectrum of an incandescent lamp - or even metal halide,
and other lamp sources – we can optimally effect the perception of
the environment.
SPECIAL FOR
PROJECTS
MULTIPLE COLOUR
SELECTION!
The DURASTRIP can be ordered "to measure", including with regard
to the colour of the light! Very warm or very cold white, a mix of
colours, individual colours.
WHITE
IP20: 2200K - 2400K - 2700K - 3000K - 3500K - 4000K - 6000K
IP68: 2400K - 3000K - 5000K
"PURE" COLOURS
DURASTRIP single colour but in the colour that counts: red, green,
blue (RGB) and blends of these colours also mixed with white.
COLOR MIX
various colours can be used on the same strip: for example, 40 cm
of red color light and then 40 cm of white color light repeated over
the whole extension of the strip.
Please consult the Florence headquarters to confirm the quantity
and design specifications to order DURASTRIP:
- Cut to size
- With the wiring of the desired lengths
- With the desired color temperatures or spectra
For this project a strip was created with a colour temperature of
2200K and a customised strip with a mixture of pure colours.
This allowed the lighting designer to create a cosy environment to
enhance the warm colours of the goods on display while offering
a pleasant and relaxing shopping experience.
4
DUAL CIRCUIT:
AVOIDING VOLTAGE DROP,
MAXIMISING LIGHT
OUTPUT
We redesigned the circuits of our LED strips introducing a
technology to double the track, this is already visible on the 2200K
IP20 strip. The double track above and below the circuit provides
an improvement of the heat dissipation, halves the current on
each power supply circuit and resets the minimum voltage drops
while standardizing the flow over the entire length of the strip. To
ensure reliability of the product always higher.
The increased amount of copper on both sides of the strip
makes it possible to reduce the operating temperature of the LED
sources; acting as a heat sink, it increases efficiency and the
life of the product. It also guarantees improved mechanical and
structural resistance of the product for greater reliability.
CERTIFIED QUALITY
All DURASTRIP and DURALUM products have CE marking which
means that they conform to the quality standards, requested of EU
Directives and also bear the UL certification mark. The UL mark is
issued after certification of the product by third parties such as UL,
an independent, non-governmental and non-profit organisation
whose mission is to ensure that products conform to standards set
by ANSI, the American National Standards Institute. UL certification
is therefore a Quality and Safety mark and is required for products
to be used in the United States and countries that make reference
to the same standards.
5
SPECIAL FOR PROJECTS
CUT FOR YOU! - BESPOKE DESIGN
The DURASTRIP can now also be ordered "to measure". Duralamp offers an interesting
customised service to those working on new or renovations projects. We supply Durastrip
LED following the design specifications, already cut to size and if necessary with the length
of the cables suitable for every application. Faster installation and a perfect service.
BUT WHAT SIZES?
Bespoke lengths! Let's presume that in your lighting project for a hotel there are 45 rooms
with dimensions of 4x4 m, with a strip on one side only; then there are 45 bathrooms with
dimensions of 1.80x1.20m with the strip on the long side. We will supply exactly 45 IP20
stripes in 4 metre rolls, complete wiring of the length necessary for the project, plus 45 IP68
strips in 1.8m rolls. Perfect!
Cut step every 10cm (or every 5cm according to the type of strip) to a maximum length of 7
metres, for DURASTRIP max 10W/m or 5m for DURASTRIP max. 15W/m. The customised
cable can have a maximum length of 7 meters.
Configuration of a “Custom made” product
Here are the necessary specifications to define a “custom made” DURASTRIP. The following elements must be defined:
1
- Existing product code
2
- Length of strip segment (the requested length must take into account the cutting spacing of every strip, 5 or 10 cm
depending on the model).
3
- Specifications of the requested end feeds (terminals): just 1 or on both sides? In the event of a cable feed on only one side the
other side of the strip will be left without connections or with an end cap with silicone sealing for IP68/IP65.
4
- Particular specifications, for example bridges etc., see the next page.
Encoding system for project planning
Code
Strip length (cm)
Length of terminal 1 (cm)
Length of terminal 2 (cm)
07348
90
60
80
= Code 07348-90-60-80
DuraStrip IP68, code 07348, 90cm long segment, with terminal wire 1 length 60cm and terminal wire 2 length 80cm
If one of the 2 terminals is not required, write '0' (zero) in the terminal space (ex.: 07348-90-60-0).
The IP20 strips are supplied with free terminals.
Any particular requests will be specified in the project modules.
6
A
AAA
OPTIONAL WIRING SOLUTIONS
A FOR “CUSTOM MADE” PRODUCTS
A
D
CC DC
CAC F DDD
lockable interconnect
lead wire
D
G
G
G
G
C
A
G
AAA
F
A
E
Factory attached jumper cables to connect
2 lengths of Durastrip for more flexibility in
complex installation requirements (max total
length 5/7 mt).
Fast connector between 2 IP20 strips
without lead wire. Standard length 5cm.
Additional connectors for fast field connections
Fast connector to connect to power IP20
strips without lead wire.
Durastrip 10cm segments connected with
a 2,5cm wire fold. Max total length 5 or 7
meters. Connected segments are suitable
to follow curved profiles.
B
F
F
F
F
E
E
E
G E
E
leadlead
wire
lead
wire
lead
wire
wire
lockable
lockable
lockable
interconnect
lockable
interconnect
interconnect
interconnect
D
D
D
D
F
CCCC
D
D
D
D
C
C
D
D DDDD
FD
FCD
CAC
CAC
CC
D
DD
AC
ACCFCFDC
C
C
D
DDD
C
D
D
CC F CD
D
A
C
D
lockable interconnect
C
C
E C
C
F
Lead wire at both ends (free wires or IP68
terminals according to the type of strip) for
power connectivity while the other end can
be used for a jumper cable to run to an
additional length of Duratape (max length
5/7 mt).
lead wire
B
B
D B
B
AAAAA AAAA
AA
AA
AAA
A
AAA
A
A
C A
A
Lead wire/dead end allows for connection to
power at one end. No wire at the other end.
G
B
In the event of custom made DURASTRIPs there are wiring terminals or bridge solutions
to meet the different needs of projects. Here below is a list of the various types.
IMPORTANT: optional wiring is different depending on the type of strip: IP20, IP68, RGB,
CTC, RGB+W: always specify the required product.
7
Zepter Apart Hotel Belgrade
IP20 INSTALLATION EXAMPLES:
Cove lighting
High lighting of architectural details
Integrated lighting in furnishings: under counters, shelves and steps
Recessed ceiling or wall lighting to create "cuts" of light
CHARACTERISTICS:
high luminous efficacy
lighting and colour uniformity along the entire length
white point control
LIGHT COLOUR
Choice of white colour temperature IP20: 2700K - 2200K - 4000K
(6000K available on request)*.
Colour constancy guaranteed by a selection of LED in a 2 step McAdam ellipse.
SPECIFICS:
Available wattages: 24W - 40W - 75W (power consumption for a 5 mt reel).
Voltage: 24VDC
Lifespan: >30.000h
Warranty: 3 years
Ra >80
Beam angle: 120°
Dimmable from 100% to 1%
Packed in 5 mt reels. Can be cut every 5 or 10 cm according to the type of strip.*
Max length for 1 connection 7 mt (5 mt for 75W).
For longer connections, make parallel connections, see page 36.
Free wire terminals.
Fitted with installation-ready 3M tape adhesive for simplified installation directly to mounting
channel or application surface; single item accessories include one wire terminal block and 1
not wired terminal block.
ACCESSORIES
See drivers, profiles, dimmers and controllers on the appropriate pages.
* For custom lengths and special white color productions see page 6.
9
DURASTRIP IP20 dimensions
24W and 40W
75W
13/32”
13/32”
3 mm 12 mm
3 mm 10 mm
13/32”
13/32”
Cutting distance
Codes: 07524 - 072240 - 07548 - 072275
10 cm
Codes: 07596 - 07696
5 cm
Accessories for cutting
The DURASTRIP IP20 has free terminals. A wired terminal block and
a non-wired terminal block are supplied. To cut to size use the cutting
kit necessary for each strip type (see the codes page at the end of
the catalogue). Detailed instructions on page 29.
KIT IP20 KT7500
- 4 pcs wired terminal block
- 14 pcs non wired terminal block
(the 14 pcs are welded in pairs of 2 pcs)
- 12 pcs silicone bridges
- 24 pcs screws for bridges
KIT IP20 KT7501
- 4 pcs wired terminal block
- 8 pcs non wired terminal block
10
FLUX LUMEN/METER
Somma
flusso 1 mt
Flux at 1dimt
1600
1450
1400
1300
1200
1050
LUMEN
1000
Wattage
Potenza
820
800
24
40
650
75
600
400
325
200
Code
Color
0
072240
072275
07524
07548
2200
Colore
07596
07696
2700
4000
Cod
STRIP LED
Ra
CQS
2200K
82
82
2700K
81
82
4000K
82
82
F126
Angoli Gamma 180°
120°
105°
105°
90°
90°
75°
75°
60°
60°
45°
EULUMDAT files for lighting calculations available
on the website, INFO TECH section.
S53
380
30°
S55
500
600
700
800 nm
380
45°
15°
0°
cd/klm
15°
30°
S57
500
600
700
800 nm
380
500
600
700
800 nm
11
Torre di Pisa - Italy
12
IP68 INSTALLATION EXAMPLES:
High lighting of external architectural details: stairs, trails, light paths.
Recessed external ceiling or wall lighting to create "cuts" of light.
CHARACTERISTICS:
lighting uniformity
white point control
strong external lighting solutions
LIGHT COLOUR
Choice of white colour temperature IP68: 3000K - 5400K *.
SPECIFICS:
Available wattages: 24W - 40W - 75W - 170W (power consumption for a 5 mt reel).
Voltage: 24VDC
Lifespan: >30.000h
Warranty: 3 years
Ra >80
Beam angle: 120°
Packed in 5 mt reels. Can be cut every 5 or 10 cm according to the type of strip.*
Max length for 1 connection 7 mt (5 mt for 75W).
IP68 terminal wire with connector (except 170W: free terminals).
channel or application surface; see next page for the included accessories.
ACCESSORIES
13
DURASTRIP IP68 dimensions
Cutting distance
Codes: 07324 - 07348
10 cm
Codes: 07200 - 07396 - 07496 - 073196
5 cm
Accessories for cutting
DURASTRIP IP68 170W have free wire terminals. Other wattages are complete with:
- 1 pc transparent male connector already connected to one side of the strip
- 1 pc transparent female connector already connected on the other side of the strip
- 1 pc transparent male connector
- 1 pc transparent female connector
- 1 pc silicone tube
For field cut use the Cutting kit here after.
CUTTING KIT FOR IP68 KT7200
- 4 pcs transparent male connector
- 4 pcs transparent female connector
- 10 pcs silicone fixing bridges
- 10 pcs silicone end cap
14
23 mm
5 mm
5 mm
5 mm
12 mm
75W
10 mm
24W and 40W
170W
FLUX LUMEN/METER
Somma
flusso 1 mt
Flux
at 1dimt
3000
2500
2500
LUMEN
2000
Wattage
Potenza
24
1500
40
1200
1200
1200
75
170
1000
600
500
300
Code
Color
0
07200
07324
07348
07396
073196
07496
3000
Colore
5400
Cod
STRIP LED
Ra
CQS
3000K
84
85
4000K
82
82
5400K
85
85
F128
Angoli Gamma 180°
120°
105°
105°
90°
90°
75°
75°
60°
60°
45°
45°
30°
S56
380
S57
500
600
700
800 nm
380
15°
0°
cd/klm
15°
30°
S58
500
600
700
800 nm
380
500
600
700
800 nm
15
Hotel Irvine - California
16
Exploring the white light spectrum
CTC IP68 INSTALLATION EXAMPLES:
Wherever changes on the white light spectrum are required, for example changing from
warm to cool white. Ideal to interact with sunlight depending on the time of day. For example
in a restaurant: a colder, livelier light at lunch time and warmer and welcoming light at dinner.
Can also be used outdoors.
CHARACTERISTICS:
white point control with variations in colour from 3000K to 6400K
no loss of quality in the spectrum emitted thanks to the use of a mix of white
and different colour temperature LED sources
lighting uniformity
LIGHT COLOUR
Choice of white colour temperature IP68: 3000K - 6400K*.
SPECIFICS:
Available wattage: 75W (power consumption for a 5 mt reel).
Voltage: 24VDC
Lifespan: >30.000h
Warranty: 3 years
Ra >80
Beam angle: 120°
Packed in 5 mt reels. Can be cut every 12 LED (10 cm).*
Max length for 1 connection 5 mt.
Free wire terminals
Can be used with 2-channels controllers, we reccomend DALI and DMX (Cod. ZKCDA,
ZKCDMX) and with Wall Touch Dimmer ZKTPC-CTC.
ACCESSORIES
17
DURASTRIP CTC IP68 dimensions
5 mm
12 mm
75W
Cutting distance
Code 07396CTC
10 cm
Included accessories
In addition to the strip the pack includes:
- 1 pc wire connection (1x3 wire)
18
FLUX LUMEN/METER
1500 lumen
800
lumen
800
lumen
3000K
4000K
F129
Angoli Gamma 180°
120°
105°
105°
90°
90°
75°
75°
60°
60°
45°
45°
30°
15°
0°
15°
6400K
cd/klm
30°
S56
380
S57
500
600
700
800 nm
380
S59
500
600
700
800 nm
380
500
600
700
800 nm
19
Irvine Spectrum Mall
Irvine - California
DURASTRIP RGB, RGB+W (White)
Combining colour and power
RGB INSTALLATION EXAMPLES:
Indoors with the IP20 versions and outdoors with the IP68, for visually striking colour effects,
making the most of the extensive capacity of chromatic interaction of the LED RGB. To
create exciting or relaxing environments, emphasise architectural details or capture the
emotions of users.
RGB+W (WHITE) INSTALLATION EXAMPLES:
Wherever a unique strip is needed for general lighting and to create colour effects. The
colours of RGB LED can be used with white to create different tones of white and to soften
the RGB. IP68.
CHARACTERISTICS:
Coloured light effects that “create” environments envisioned by the lighting designer; they can
be modified or reproduced at any time thanks to the “scenes” set on the controllers.
LIGHT COLOUR
RGB: Wavelength value of the spectrum: red 625nm; green 520nm; blue 450nm.
RGB+ White: red 625nm; green 520nm; blue 450nm and white 3000K.
SPECIFICS:
Available wattages:
RGB IP68: 50W - RGB IP20 40W (power consumption for a 5 mt reel).
RGB+W IP68: full power on RGB+W (White)= 47W; only white= 28W; only RGB=19W (power
consumption for a 5 mt reel).
Voltage: 24VDC
Lifespan: >30.000h
Warranty: 3 years
Ra >90 for 3000K RGB+W white color
Beam angle: 120°
Packed in 5 mt reels. Can be cut every 5 or 10 cm according to the type of strip*
Max length for 1 connection 5 mt.
Terminals details: see next page.
RGB: can be used with DMX 3-channels controllers, code ZKCDMX, ZKCDMX-R e
ZKCDMXW and with Wall Touch Dimmer ZKTPC-RGB+W (White).
RGB+W (White): can be used with 4-channels controller's code ZKCDMXW in order to
obtain all desired shades in a smooth continuous way and also with ZKTPC-RGBW Wall
Dimmer Touch.
ACCESSORIES
* For custom lengths and special white color productions or for "pure color" strips, see page 6.
21
DURASTRIP RGB, RGB+W (White)
DURASTRIP RGB
and RGB+W IP68
Cutting distance
dimensions
Codes: 07372RGB + 07372 RGB+W (White)
10 cm
5 mm
15 mm
50W
DURASTRIP
RGB IP20
dimensions
Cutting distance
Codes: 07340RGB
10 cm
3 mm
13 mm
40W
Included accessories
Included in evey pack:
RGB IP20
- 1 pc wired terminal block
- 1 pc non wired terminal block
RGB IP68
- 1pc transparent male connector already connected to one side of the strip
- 1 pc transparent female connector already connected on the other side of
the strip
- 1 pc transparent male connector
- 1 pc transparent female connector
22
The RGB LED source, which has a low CRI (Color Rendering Index) is enhanced by the calculation system used by the CQS. The CQS
makes it possible to appreciate the capacity of this type of source to reproduce colour tones in applications where it is important to enhance
colours (food, retail, etc.). The CQS shows that the RGB source, despite having a very low Ra, makes the colours present in the environment
brighter and more vivid.
Ra=2
Qa=48
S60
380
S61
500
600
700
800 nm
380
S63
380
S62
500
600
700
800 nm
380
S64
500
600
700
800 nm
380
500
600
700
800 nm
500
600
700
800 nm
S65
500
600
700
800 nm
380
23
DURALUM-Flexible lighting solution
INSTALLATION EXAMPLES:
Indirect lighting for interiors where it is necessary to follow particularly irregular profiles:
decorative or structural elements, niches, signs, markers etc...
PARTICULAR CHARACTERISTICS:
Flexible system of continuous LED modules mounted into multiple arrays. Each array can
be bent horizontally up to 90° and 45° vertically from the next module for complex cove and
niches applications. Each LED PCB incorporates aim adjustability with +/- 60° rotation from
vertical in order to attain a perfect control of the direction of the light. Each module carries a
replaceable PCB with 6 LED array. The system makes it possible to have products made to
specifications (subject to prior approval of the specific project) with the possibility to choose
the pitch of the lamp holder, the light colour and the length.
LIGHT COLOUR
2700K (other color temperatures available upon project approval).
SPECIFICS:
Available wattages: 7W /meter (different wattages available upon project's approval)
Spacing: 6cm (differnet spacing available upon project's approval).
Voltage: 24VDC
Lifespan: 50.000h
Warranty: 3 years
Ra >80
Beam angle: 120°
Standard length: 122 cm.
ACCESSORIES
Adjustability and rotation
DURALUM can be controlled by the same systems used to control a white DURASTRIP.
See drivers, dimmers and controllers on the appropriate pages.
* For custom lengths and special white color productions enquire with the sales force.
90°
F127
Angoli Gamma 180°
120°
80
105°
90°
90°
80
75°
160
60°
240
45°
up to +/-60°
105°
320
30°
15°
75°
60°
45°
cd/klm
400
0°
15°
30°
25
DURALUM dimensions
24mm
24mm
19mm
19mm
24mm
24mm
19 mm
19 mm
51 mm
51 mm
51mm
51mm
Accessories dimensions
27,1mm
Aluminum mounting channel for straight
run applications.
39,5mm
30,8mm
Clear polycarbonate lens for channel.
Protects LED modules from direct contact.
32,5mm
26mm
25,5mm
38mm
63,5mm
26
38mm
Compact junction box used to cover
terminal block connections.
DURALUM accessories
White PVC cable mounting
clamp secures Duralum cable
to surface with a single
screw on each side of clamp
(screws not included).
DRL-EC
Each length of Duralum
can be terminated with silicone
end caps to protect
and insulate the conductors
at the end of a run.
DRL-LENS-C-4
Clear polycarbonate lens
for channel. Protects LED
modules from direct contact.
Comes in 1250 mm sections.
Aluminum mounting channel
for straight run applications.
Channel screws into place,
lamp sockets fit into channel
ensuring linear integrity and
reducing installation time. Finish
is standard satin aluminum.
Comes in 1250 mm sections.
Replacement PCB.
5 pcs pack. Light color
temperature to be specified.
DRL-JBOX
Compact junction box
(63.5mm x 38mm x 38mm)
used to cover terminal block
connections.
One end of the terminal block
screws directly into Duralum
conductors, the other end
connects (accepts 0,75-5mm2
wire) to power supply. Terminal
block included.
27
MOUNTING INSTRUCTIONS
CUTTING SEQUENCE FOR DURASTRIP IP68
Cut exactly where indicated
with the scissors symbol
on the strip in order to optimise
welding of both parts.
Fill the end cap with
the silicone supplied and insert
the strip into the end cap
to restore the waterproof seal.
Cut the silicone cover
then uncover and clean
the contacts
Insert the wire of the jack
into the end cap
IP68: seal the jacks properly to
get a good connection.
Use the silicone supplied
to re-establish the waterproof
seal after every cut.
+ white
Connect and solder the wires
of the jack IP68 to the contacts
of the strip paying attention
to the polarity.
28
- transparent
CUTTING SEQUENCE FOR DURASTRIP IP20
Cut exactly where
indicated with the scissors
symbol on the strip.
Open the connector,
insert the strip and close
the connector.
ASSEMBLING THE DURASTRIP
INSTALLATION:
FIXING TO SURFACES/PROFILES
All DURASTRIPS are fitted with double sided 3M tape on the back for
sticking to surfaces or profiles. Clean and remove grease accurately
from the surface before applying the strip.
USING THE CLIP:
Every pack of DURASTRIP comes complete with a plastic assembly
clip for the IP20 and a silicone clip for the IP68. Be careful not to
snag the LED chip when fixing the clips.
29
m
m
m
m
IP20 = 12 mm
IP68 = 12,5 mm
,5
11
IP20 = 20 mm
IP68 = 28,4 mm
IP20 = 13 mm
IP68 = 17,4 mm
IP20 = 10,2 mm
IP68 = 11 mm
IP20 = 9 mm
IP68 = 11,5 mm
IP20 = 16 mm
IP68 = 20,4 mm
IP20 = 13 mm
IP68 = 17,4 mm
IP20 = 16 mm
IP68 = 20,4 mm
TIPS FOR THE INSTALLER:
We recommend you make precise cuts in
the aluminium profiles to avoid damage to the
electric circuits in the IP20 strips, or loss of the
watertight seal in the IP68 and also to ensure
that subsequent profiles are aligned correctly.
In the event of assembly with DURASTRIP
IP68: remember the IP68 connector is
installed outside the profile.
30
RECESSED
SURFACE
AT 45°
CHARACTERISTICS:
Provides durability to the installation, protects the strips mechanically and gives more stability
to the installation with linear profile, optimizes heat dissipation. Recommended in case of
external applications.
5
9,
=
20 =
IP
68
IP
IP20 = 9 mm
IP68 = 10,8 mm
INSTALLATION EXAMPLES
IP20 = 18,5 mm
IP68 = 19 mm
IP IP2
68 0
= =1
20 6
,4 mm
m
m
ALUMINIUM PROFILES FOR DURASTRIP IP20 AND IP68
SPECIFICS:
Extruded anodized aluminium complete with opal plastic diffusing cover. Snap on screen,
easily removable.
Standard length: 2000 mm.
Comes in two versions to contain DURASTRIP IP20 and DURASTRIP IP68: see the relative
codes on the final pages.
ACCESSORIES:
Assembly kit includes supports to fix to the wall/ceiling and end caps with holes for wiring
or without holes for closing.
WALKOVER PROFILES FOR DURASTRIP IP20 AND IP68
FLUSH WITH THE FLOOR
PARTICULAR CHARACTERISTICS:
White satin polycarbonate walkover profile with recessed aluminium support. Gives durability
to the installation and protects the strips mechanically. The DURASTRIP housing is “filled” to
give maximum mechanical protection, to protect the strips from external agents and provide
smooth continuous illumination.
SPECIFICS:
The profile houses strips up to a maximum of 17 mm wide. See the code on the final pages.
19,4 mm
8 mm
25 mm
16 mm
31
TRANSPARENT SEAMLESS PROFILES FOR DURASTRIP IP20
SURFACE OR RECESSED MOUNTING
SURFACE MOUNTING WITH LIGHT EMISSION FROM AN INCLINED ANGLE OF 45°
CHARACTERISTICS:
Transparent polycarbonate BASE profile for surface or recessed mounting. It can be
completed with cover in transparent or frosted polycarbonate (frosted upon order). The
cover fits on the base eliminating any side rim for an extremely clean luminous effect. For
Durastrip IP20. L=2,5 m (8ft).
White polycarbonate profile for surfaces mounting with emission of light from inclined plane
at 45°. Can be completed with a cover in transparent or frosted polycarbonate (frosted upon
order). For Durastrip IP20.
”66.0
SPECIFICS:
”02.0
9,5 mm
Standard length: 2,5 mt.
”573.0
16,7 mm
”26.0
”66.0
”02.0
5 mm
”02.0
9,5 mm
15,7 mm
”573.0
”573.0
16,7 mm
17,5 mm
45° mounting
16 mm
32
Strip installed facing upwards
”66.0
”26.0
”26.0
ARCHITECTURAL PROFILES FOR DURASTRIP IP20
50,55 mm
50 mm
12,4 mm
12,5 mm
47,4 mm
35 mm
33 mm
85 mm
47,4 mm
SURFACE MOUNTING, inside niches
AT 45°
CHARACTERISTICS:
The bidirectional profile makes it possible to create particular light effects on walls or
ceilings. The dome screen and corner dome profiles can both hold two DURASTRIP IP20.
SPECIFICS:
Extruded anodized aluminum profiles to be completed with a polycarbonate cover. Rear support
to be mounted to the surface with screws: the profile is then attached to the said support. The
double emission profile's central body can accomodate the driver (code ZK7360).
ACCESSORIES:
Cutting kit inlcudes 2 closure caps.
m
m
49,7 mm
2
,4
12
50 mm
TIPS FOR THE INSTALLER:
Make sure to have enough room to slide the
profile on the support.
33
CEILING MOUNTING
WITH 4 STRIPS
FOR DIRECT LIGHT
CEILING MOUNTING
WITH 3 STRIPS
FOR DIRECT LIGHT
SUSPENDED MOUNTING
WITH TWO STRIPS
FOR INDIRECT LIGHTING
AND 4 FOR DIRECT LIGHT
DURAPROFILE PLUS
DOUBLE EMISSION ARCHITECTURAL PROFILE
14mm 14mm 14mm 14mm
SUSPENSION = dual emission
SURFACE = unidirectional emission
15mm
30mm
60mm
17mm
73mm
56mm
23mm
62mm
CHARACTERISTICS:
Linear architectural profile optional in direct, indirect emission or both, for high levels of light
emission. The direct emission can be used with 1 to 4 strips; indirect emission made with
two strips.
SPECIFICS:
KTPREDESO
PRODESO-FLR
Extruded aluminum profile completed with polycarbonate cover, side closure caps and with
white opal polycarbonate screens according to the chosen mounting fashion (flat front screen
for direct emission and flat front screen and rear pair of screens for indirect emission).
ACCESSORIES:
Flat front opal polycarbonate screen.
Set of 2 rear flat opal polycarbonate screens.
Set of 2 closing caps, necessary for mounting.
Suspension kit for ceiling suspended mounting.
CEILING MOUNTING FOR
UNIDIRECTIONAL EMISSION
PRODESO-FLR
34
SUSPENSION
WITH DUAL EMISSION
Island Hotel - Newport Beach, California
DRIVERS
The vast potential of DURASTRIP can be realized through multiple power control and
automated options. Numerous solutions can be achieved with available combinations.
The solutions to power lighting systems are composed of a series of SELV-equivalent
constant voltage power supplies for independent mounting, with the TUV quality mark.
These drivers cover the power range from (20)50-200W, for both IP40 version as well
as IP67 version with metal case to cover all kinds of indoor as well as more “difficult”
outdoor installations. In particular the 60W driver is designed to fit into architectural
aluminium profiles
IP67
IP40
CONNECTION DIAGRAM
Supplier
Driver
ELECTRICAL CONNECTION: connections in series or parallel
STRIP POWER
36
LENGTH
CONNECTION
DRIVER
170 W
5m
-
200W
75 W
5m
-
100W
75 W
10 m
Parallel
200W
40 W
10 m
Series
100W
40 W
15 m
Parallel
200W
24 W
15 m
Series
100W
24 W
20 m
Parallel
100W
NOTE
Each 5m must be installed in parallel
CONTROLLERS
Duralamp chose to divide the traditional power control system with 2 distinct devices, power
supply and controllers allowing for greater flexibility of installation. Controllers provide the
essential range of configurations DALI, PUSH-DALI, 1-10V, DMX (RGB+RGB+W [White]).
Dimming and control systems can be used to improve the ambient aspect: they help creating
unique soothing or lively environments. Moreover they have an important function of energy
saving: by varying the emission and/or activating/deactivating the system or appliances,
they allow for the optimization of solar lighting and energy consumption.
DURALAMP interfaces can control from 120 to 450W with high frequency PWM technology,
compact housings and very high efficiency. This minimizes heat dissipation and maximizes
the linearity of dimming and thus ensures dimming down to the minimum, close to 1% and
with no flicker.
DMX INTERFACE
1-10V DIMMING INTERFACE
DALI INTERFACE
DMX512, which abbreviation is DMX (Digital
MultipleX), is a communication protocol
mainly used to control lighting (even LED
type), from computers or control units. It is
normally used to control coloured lighted or
white lighted appliances (RGB) with variable
temperature. Thanks to the high transmission
speed of the data, the DMX allows making
dynamic and even complex sceneries.
A DMX network consists in 512 channels;
the number of appliances that can be
controlled cannot be defined beforehand,
as it depends on how many DMX channels
each appliance uses. E.g., if every appliance
of the DMX network uses 3 DMX channels,
the network can contain 170 appliances.
ZKCDMX-R code version: Equipped with
RJ45 connector for DMX signal, complete
with looping system and remote sensor
with plug (20 cm cable). It can be used
in a traditional way or with remote control
included in the packaging (signal distance
10 mt in free air).
The 1-10V luminous intensity control system
runs with analog technology: 1 corresponds
to 0% and 10 to 100% of the lamp emission.
The intensity can be adjusted by using the
linear curve or logarithmic curve and it is the
simplest system to install.
The connection is carried out by 2 polarity
wires placed between the power supply
and controller. It can be used with active or
passive control systems.
The DALI (Digital Addressable Lighting
Interface) is a digital protocol interfacing with
the power supplies. It is widely used in the
lighting field as it provides visible benefits
compared to the 1-10V analog control
technology (it is essentially a flexible, digital
control that allows addressing the single
appliances). The DALI protocol allows
defining appliance units and managing the
lighting sceneries, to create the right lighting
of an ambient according to its use. Different
lighting sceneries can be configured and
enabled using a simple key, without involving
the system wiring.
The DALI protocol is more simple and
economic compared to the integrated
management systems of a building (building
management). A DALI network can control
up to 64 appliances/lamps.
The interface has the Push/DALI function
for a simple management of every single
spot light.
37
DIMMERS
Options such as regulation of light levels, changes in colour temperature and choosing
RGB colour effects maximise your lighting design and manage your energy savings. A new
series of “stand alone” wall control systems with touch technology have been introduced
that integrate perfectly with existing installations. This affords the end user full flexible control
of the LED strips. It makes it possible to control up to 4 zones (understood as rooms
or different dimmer systems) both synchronized or independently controlled between the
various zones.
All touch panels have a DMX data output connector (in accordance with DMX512, 1990
protocol) and can be interfaced with the existing dimmer system by programming the
dimmer setting. The touch systems have a memory to record preferred “scenes” for each
environment to maintain light levels, white or colour tones and to manage sophisticated
effects in an easy way. All dimmer systems are easy to configure and are compatible with
ZKCDMX, ZKCDMX-R, ZKCDMXW controllers or with the existing system installed to give
the user a renewed environment while containing costs. We offer cost effective lighting
solutions for complex lighting designs and applications.
External interface in highly touch sensitive tempered glass to give
an immediate and precise response to the touch
38
DURASTRIP
CONTROLLERS:
1-10V scheme
Wire section suitable to length and load of installation
L +
N -
Supplier
Driver
+
-
Controller
1-10
+
-
Digital signal
+
+
+
-
-
Controller
DALI 2x5A
DA1 DA2
CH2
DALI IN - Push
DURASTRIP
CONTROLLERS:
DALI scheme
L
N
Supplier
Driver
Alimentatore
100W
Driver 100W
Max 5A/ch
Strip 1 - 24/48/96W 24V
Alimentatore
100W
Driver 100W
CH1
+
-
Controller
DALI 2x5A
DA1 DA2
DALI IN - Digital signal
CH1
CH2
Strip 2 - 24/48/96W 24V
+
Max 5A/ch
Strip 2 - 24/48/96W 24V
CONTROLLERS:
DALI scheme (Push)
Supplier
Driver
Strip 1 - 24/48/96W 24V
DURASTRIP
L
N
39
DURASTRIP
CONTROLLERS:
DALI scheme for CTC
linear system with master
and slave module
Driver 200W
L
N
Supplier
Driver
Modulo master
+
Controller
DALI 2x5A
-
DALI IN
CH1
+
C
CH2
W
DALI IN - Digital signal
Strip CTC
+
C
W
+
C
W
Strip CTC
Example of “slave strip” module
DURASTRIP
CONTROLLERS:
DMX scheme
L
N
+
-
Supplier
Driver
Controller
DMX
CHR
CHG
CHB
Strip 1
CHR
CHG
CHB
Strip 2
CHR
CHG
CHB
Strip 3
+
+
Signal - DMX512
Controller DMX
+
DURASTRIP
CONTROLLERS:
DMX IR scheme
L
N
+
-
CHR
CHG
CHB
Strip
+
FOR 12V - MAX n. 3 STRIP RGB 72W
Supplier
Driver
Controller
DMX
Max 10mt
Strip 1
Strip 2
Receiver
Controller DMX
Strip 3
40
CHR
CHG
CHB
+
Strip
DURASTRIP
CONTROLLER RGB+W
(Cod. ZKCDMXW)
L
N
+
-
Supplier
Driver
Controller
RGBW
Strip
RGB
Signal - DMX512
Strip
WW
Strip
RGBW
DURASTRIP
DIMMER TOUCH
L
N
+
-
Supplier
Driver
Controller
DMX
Strip 1
Strip 2
Signal - DMX512
Strip 3
Zone 1
L
N
+
-
Supplier
Driver
Controller
RGBW
Strip
RGB
Signal - DMX512
Strip
WW
Strip
RGBW
Zone 2
L
N
+
-
Supplier
Driver
Controller
RGBW
Strip
CTC
Signal - DMX512
Strip
CTC
Strip
CTC
Zone 3
L
N
+
-
Supplier
Driver
Controller
RGBW
Strip
WW
Signal - DMX512
Max power indications for the use
of DURASTRIP with the controllers,
see page 44
Strip
WW
Zone 4
Strip
WW
41
CODES TABLES
PRO
DURASTRIP
All DURASTRIP are items within the PRO range of products, enjoying a standard Warrary of 3 Years.
Strip
Warm
White:
Ra>80
L70
L
L2
WARRANTY
3 YEARS*
III
L1
30000 h
DURASTRIP CTC Total White IP68
N°
Barcode
L
L1 L2
LED
80119058
07396CTC
120°
600
12
5 5000
33978
15
75
24VDC 1500/m* 3000-6400
* Value referred to natural color temperature, 4000K. On the two ends of the spectrum, 3000K and 6400K, consider 800 lm/m.
 It can be used with 2-channel controllers, we recommend DALI and DMX, Cod. ZKCDA; ZKCDMX.
Code
Watt
Volt
Lumen
K
DURASTRIP RGB IP68 + WHITE 3000K
Code
Watt
Volt
Light
tonality
RGB+3000K
Lumen
07372RGBW
364/m*
47
24VDC
* Value referred to color temperature 3000K.
120°
N°
LED
150
120°
120°
120°
120°
120°
120°
N°
LED
600
300
300
600
600
1200
L
L1
L2
15
5
5000
L
L1
L2
12
10
10
12
12
23
5
5
5
5
5
5
5000
5000
5000
5000
5000
5000
Barcode
80119058
38904
15
-
Barcode
80119058
32353
33206
33190
33183
33749
33176
15
16
16
15
15
10
-
Barcode
80119058
33213
15
-
Barcode
80119058
32360
39222
15
15
-
Barcode
80119058
34395
38881
34418
38898
33985
33992
18
16
18
15
22
22
-
Watt
Volt
Lumen
K
07200
07324
07348
07396
07496
073196 *
75
24
40
75
75
170
12VDC
24VDC
24VDC
24VDC
24VDC
24VDC
1200/m
300/m
600/m
1200/m
1200/m
2500/m
3000
3000
3000
3000
5400
3000
* High power strip with double LED raw. We recommend using it with aluminium profiles to optimise heat dissipation.
Item with loose cables (without connector).
DURASTRIP RGB IP68
Code
Watt
Volt
Lumen
07372RGB
50
24VDC
-
Light
tonality
RGB
120°
N°
LED
300
L
L1
L2
15
5
5000
N° LED
L
L1
L2
300
300
13
13
3
3
5000
5000
N° LED
L
L1
L2
300
600
300
600
600
600
10
10
10
12
12
12
3
3
3
3
3
3
5000
5000
5000
5000
5000
5000
DURASTRIP RGB IP20
Code
Watt
Volt
Lumen
07201
07240RGB
40
40
12VDC
24VDC
-
Light
tonality
RGB
RGB
120°
120°
DURASTRIP SMD IP20
42
Code
Watt
Volt
Lumen
K
07524
072240
07548
072275
07596
07696
24
40
40
75
75
75
24VDC
24VDC
24VDC
24VDC
24VDC
24VDC
325/m
820/m
650/m
1050/m
1300/m
1450/m
2700
2200
2700
2200
2700
4000
120°
120°
120°
120°
120°
120°
Technical data are subject to tolerances and may vary; any update is published on the website www.duralamp.it
Code
* Specific guarantee of the LED products: consult the site
DURASTRIP SMD IP68
ADDITIONAL CUT AND MOUNT KIT FOR STRIP
Additional cut and mount kit for Strip IP68 (code 07200-07324-07348-07396-07496)
Barcode
80119058
32520
Code
KT7200
This kit includes 8 end caps, 4 transparent connectors.
-
Additional cut and mount kit for Strip IP20
KT7500*
For codes 07596 - 07696
KT7501*
For codes 07524 - 07548
KT2PA
For codes 072240 - 072275
* Each kit includes 8 terminal block. 4 cabled terminal blocks (15 cm long wire). 12 silicone fixing bridges with screws.
PRO
-
DURALUM
DURALUM
Code
08U27242
new
DRL-CHAN-4
DRL-LENS-C-4
DRL-CC
DRL-CM-WW-27-24
DRL-JBOX
DRL-EC
Watt/
meter
7
VOLT
24VDC
Lumen/
meter
472
N° modules/ Spacing
L
meter
on center
2700 120°
10
60
1220
Barcode
80119058
-
1
-
1250
1250
-
1
1
5
1
5
-
Barcode
80119058
32377
32384
33312
39581
33329
33336
1
1
1
1
1
1
-
K
Aluminum mounting channel
Clear polycarbonate lens for DURALUM channel
Mounting clamps (screws not included)
2700K color temp. replacement PCB
JBox (Terminal block included)
Duralum end caps
DRIVER FOR STRIP
DRIVER FOR STRIP
Code
new
L
L1
L2
ZK07224*
ZK07296**
ZK7350
ZK7360
ZK73100
ZK73200
Watt
Volt IN
Classe
24
96
50
60
100
200
100-240
100-240
200-240
200-240
100-240
100-240
II
II
II
II
I
I
Volt
OUT
12VDC
12VDC
24VDC
24VDC
24VDC
24VDC
PF
L
L1
L2
0,9
0,9
0,9
0,9
0,9
0,9
95
168
185
305
216
238
45
60
64
30
68
63
30
39
22
17
34
43
* For 1 m ** For 5 m
 Drivers only for DURASTRIP.
 SELV equivalent; protection device in case of short circuit or overload in the secondary circuit.
24V drivers have loose wires connection and are TUV marked.
12V drivers are provided with connectors.
 ZK73100-ZK73200: IP67
 These drivers are dedicated to the strips and must not be used with other devices.
43
CODES TABLES
CONTROL INTERFACE FOR DURASTRIP
DALI CONTROLLER FOR DURASTRIP WITH WHITE LIGHT
Code
Max current (A)
Volt OUT
Volt IN
Connection
IP
L1
L2
L3
ZKCDA
12-24VDC
Screw
20 168 51
2x5
12-24VDC
 2-channel controller, which can be also used with Durastrip CTC Total White.
35
Barcode
80119058
33367
1
-
Barcode
80119058
33374
1
-
1-10V CONTROLLER FOR DURASTRIP WITH WHITE LIGHT
Code
Max current (A)
Volt OUT
Volt IN
Connection
ZKC1-10
12-24VDC
Screw
10
12-24VDC
 It can be used with all White light Durastrips, except for CTC Total White.
IP
L1
L2
L3
20 168 51
23
DMX CONTROLLER FOR DURASTRIP RGB (OR WHITE ON 3 CHANNELS)
Code
Max current (A)
Volt OUT
Volt IN
Connection
IP
L1
L2
L3
Barcode
80119058
33442
36795
ZKCDMX
12-24VDC
Screw
20 168 51 23
1
6/CH
12-24VDC
ZKCDMX-R*
5/CH
12-24VDC
12-24VDC
RJ45/Screw 20 178 42 33
1
 It can be used with all Durastrip RGB, CTC and white.
* Version with RJ45 connector, which can be used in a traditional way or with remote control included in the package.
-
DMX 4 CHANNELS CONTROLLER FOR DURASTRIP RGB+WHITE (OR 4 CHANNELS)
Code
Max current (A)
L2
L3
ZKCDMXW
12-24VDC
Screw
20 168 51
5/CH
12-24VDC
 Can be used with Durastrip RGB+white.
 Connection diagrams are available at www.duralamp.it (in the product datasheet).
22
How to use DURASTRIP with our
controllers? Here the indications
of maximum power.
Volt OUT
Volt IN
Connection
ZKCDA
ZKC1-10
ZKCDMX / ZKCDMXW
ZKCDMX-R
IP
L1
DURASTRIP 12VDC
2x60W
120W
72W/CH
60W/CH
Barcode
80119058
38942
1
-
DURASTRIP 24VDC
2x120W
240W
144W/CH
120W/CH
WALL TOUCH DIMMER FOR WHITE LIGHT DURASTRIP
Input
Number of
Number
Number
Barcode
Photo L1 L2 L3
80119058
voltage DMX channels of areas of scenes
ZKTPC-DIM
4
4
4
1
86 86 10
39635
1
5VDC
 Each channel can have 256 levels of light variation and 4 favourite scenes can be saved.
 "Memory" function: the last colour temperature chosen is recalled when the light is switched back on again; 3 scenes can be saved.
Code
WALL TOUCH DIMMER FOR CTC DURASTRIP
Input
Number of
Number
Number
Barcode
Photo L1 L2 L3
80119058
ZKTPC-CTC
8
4
3
2
86 86 10
39642
1
5VDC
 Each channel can have 256 levels of light variation and 3 favourite scenes can be saved.
 "Memory" function: the last colour temperature chosen is recalled when the light is switched back on again; 3 scenes can be saved.
Code
WALL TOUCH DIMMER FOR RGB DURASTRIP
Input
Number of
Number
Number
Barcode
Photo L1 L2 L3
80119058
ZKTPC-RGBW
16
4
4
3
146 106 10
39659
1
5VDC
 "Memory" function: the last colour level chosen is recalled when the light is switched back on; 4 favourite scenes can be saved.
 Simultaneous or sychronous control of the RGB colours and white. 36 setting modes.
 Dimmer’s driver included in the packaging (220-240Vac / 5Vdc).
Code
44
Technical data are subject to tolerances and may vary; any update is published on the website www.duralamp.it
WALL TOUCH DIMMER
DURAPROFILE PLUS
DOUBLE EMISSION ARCHITECTURAL PROFILE
DURAPROFILE PLUS - ALUMINIUM DOUBLE EMISSION PROFILE *
Code
PRDESO
PRDESO-SL
PRDESO-FL
PRDESO-FLR
KTPRDESO-FL
KTPRDESO
* Available upon request
Description
Double emission aluminium profile
Rear support for surface mount
Front screen in flat opal polycarbonate plate
Couple of opal polycarbonate rear screen
Set of two side caps flat screen
Suspension kit
L
1220
1220
1220
1220
-
Barcode
80119058
39970
39987
39994
40020
40068
40051
1
1
1
1
1
1
-
PROFILES IN ARCHITECTURAL ALUMINIUM FOR DURASTRIP IP20
PROFILES FOR ARCHITECTURAL DURASTRIP IP20
Code
PRDE
PRDSAP
PRDSAN
PLDSAP-C
PLDSAN-C
KTDEAP
KTDSAP
KTDSAN
Description
Double emission aluminium profile
Aluminium profile for dome cover
Aluminium profile for dome cover, mounting at 45°
Polycarbonate dome cover
Polycarbonate dome cover for profile mount. 45°
Set of 2 caps for double emission profile
Set of two end caps for dome profile
Set of 2 caps for dome profile, mounting at 45°
L
1220
1220
1220
1220
1220
1220
1220
1220
Barcode
80119058
40150
39796
39802
39819
39833
39857
39864
39871
1
1
1
1
1
1
1
1
-
Barcode
80119058
-
1
1
1
5
5
5
-
Barcode
80119058
-
1
1
1
1
1
1
1
-
DURASTRIP PROFILES
PROFILES FOR IP20 DURASTRIP
Code
PRAP20
PRIN20
PRAN20
KTPRAP20
KTPRIN20
KTPRAN20
Mounting
Surface mounting - for IP20 - 5 pieces pack
Recessed mounting - for IP20 - 5 pieces pack
Corner mounting 45° - for IP20 - 5 pieces pack
Kit caps and clips for mounting surface - for IP20
Kit caps and clips for mounting recessed - for IP20
Kit caps and clips for mounting angle 45° - for IP20
L
2000
2000
2000
-
PROFILES FOR IP68 DURASTRIP
Code
PRAP68
PRIN68
PRAN68
KTPRAP68
KTPRIN68
KTPRAN68
PRINTC*
Mounting
Surface mounting - for IP68 - 5 pieces pack
Recessed mounting - for IP68 - 5 pieces pack
Corner mounting 45° - for IP68 - 5 pieces pack
Kit caps and clips for mounting surface - for IP68
Kit caps and clips for mounting recessed - for IP68
Kit caps and clips for mounting angle 45° - for IP68
Walk-over profile for strip IP68 and IP20
L
2000
2000
2000
1000
* Walk-over profile with white satin polycarbonate covering and recessed aluminum support, housing both strip IP20 and IP68.
Available upon request.
 IP68 strip connector shall be installed outside the profile.
45
Island Hotel - Newport Beach, California
46
Tustin Market Place - Irvine, California
Kamniška Bistrica Bridge - Kamnik - Slovenia
47
DURALAMP S.p.A. Società Unipersonale
Via Di Limite, 148
50013 Campi Bisenzio (Firenze)
Tel. +39 055 894881
Fax +39 055 8953032
e-mail: [email protected]
www.duralamp.it
© Copyright 2015 - Duralamp SpA
All data and pictured provided in this catalogue are for reference only: since they might change during mass production, they have to be considered nominal values with tolerances.
Duralamp Spa reserves the right to modify its products in any moment, for technical or commercial reasons.
Restaurant Il Lago Saint-Petersburg
code: DURASTRIP EN

durastrip - Targetti

Transcription

Similar documents

V115 Strip Series Cladding Strip Cladding Craftline Strip Cladding

modern designs - Resene Paints

1 Window Jumbo Strip Game

The Domino A200 The Domino A200

`Tyci Tavoli series of tables` product card

A-Series Plus 4pp V3

XD300U Multimedia Projector from Mitsubishi Electric

Playtime Paris – more European finds!

ExCam® IP1365

Quilting Classroom