Satellite Self Installation Manual

Satellite
Self-Installation
Manual
July 2014
1.
Getting Started
This Shaw Direct Installation Manual provides all of the information required to setup your satellite
system. The manual provides step-by-step instructions, however skills in construction, wiring and
assembly will also be required to successfully complete the installation.
Self-Installation Explained:
Self-Installation of your Shaw Direct system can be broken down into three (3) basic steps:
1. Dish Assembly consists of assembling the pieces provided to form a complete satellite dish.
2. Dish Installation involves location suitable mounting locations, finding the satellite in relation
to your surroundings, and physically attaching the dish to your structure.
3. Connecting the Receiver consists of connecting your Shaw Direct satellite receive to the dish,
tuning to the correct channel, and fine-tuning the dish based on the satellite signal readings
provided.
IMPORTANT: We do not recommend installing the satellite dish on your roof, unless absolutely necessary. If
you choose to mount the dish on the roof, we strongly recommend consulting a building or construction expert
before installation.
IMPORTANT: Read this manual thoroughly before you start.
WARNING: All satellite dish systems must be properly grounded. Improper grounding can result in damage,
serious personal injury, and/or system performance issues. National, provincial and local electrical codes may
require you to ground the dish directly and to insert a grounding block in the coaxial cables running from the
dish to the receiver inside the building. Before beginning installation, carefully read the section on grounding
the dish (see section 10).
This installation requires you to:
•
Use hand tools such as a drill
•
Determine whether water pipes, electrical wiring or gas lines are close to the installation area
•
Route coaxial cable through walls and under floors
•
Use a compass, protractor and carpenter’s level
•
Use a ladder to climb structures
•
Know your local, provincial and national grounding codes
If you do not have the experience to perform these tasks, contact Shaw Direct for assistance.
1
You will need the following tools:
•
Philips screwdriver
•
3/8” hex or flat-head screwdriver
•
7/16 hex wrench, open or combination end
•
Electric drill and bits
•
Carpenter’s level
•
Compass
•
Protractor
If you are installing a 75 cm dish, you will also require:
•
2 - 13 mm wrenches (one to hold and one to tighten)
NOTE: You must use the mast that came with the dish, unless you are using a tripod.
Dish Kit Contents
60 cm Dish Kit
60 cm Elliptical Dish
60E xKu LNB
75 cm Dish Kit
Clamp Mount Assembly
Hardware (see below)
Satellite Feed Support Arm
1¾ ” diameter
Universal Mount Assembly
75 cm
Elliptical
Dish
75E xKu
LNB
Clamp Mount Assembly
Hardware (see below)
Satellite Feed Support Arm
2” diameter
Universal Mount Assembly
2
To facilitate assembly of the dish, arrange the hardware as follows. The number corresponds to the
steps listed in Section 3.
60 cm Hardware
4
3
2a
1
2b
5
75 cm Hardware
4
3
1
2a
2b
Missing pieces?
The Shaw Direct Self Install Kit contains many additional pieces to help you complete your
installation, including:
•
Screws to attach the Universal Mount to
•
your structure
Silicone to seal the cable entry holes and
dish mount holes
Enough coaxial cable for two lines
•
A compass to help locate the satellite
•
Dual grounding block and ground wire
•
Hardware to route and secure the coaxial
•
Dual coax wallplate
•
cables, including zip ties and cable clips.
Give us a call at 1.888.554.7827 for more information or to purchase a Self Install Kit.
3
Helpful Hints
Key points to remember when installing your Shaw Direct System:
•
Do not drill any holes until you’ve confirmed the best location for the dish.
•
Make sure the installation of the dish conforms to local electrical and building codes, zoning
requirements and other applicable laws and regulations. If you are unsure, contact a local
electrician or building inspector for assistance.
•
For possible periodic removal of snow, choose a site that is easily accessible.
•
Ensure there are no visible obstructions between the dish and your line of sight to the
satellites. Keep in mind that trees will grow up and outward and may eventually block the
signal.
•
The maximum allowable length for the RG-6 coaxial cable connecting the receiver to your
dish is 150 feet. Consult Shaw Direct if the cable will exceed this length.
•
Use only RG-6 grade coaxial cable. Using lower grade RG-59 coaxial cable may result in
excessive signal loss and poor reception. Cable grade type is indicated on the outer jacket of
the cable.
Do not install the dish:
•
Under power lines
•
Where it may be easily tampered with
•
Where it is exposed to high winds, during windy or stormy conditions
2. Mounting Locations
Your dish must be mounted on a solid base. To ensure your dish doesn’t move in windy conditions,
choose a location where it can be securely fastened. The mounting surface should be rigid and solid.
IMPORTANT: The Elliptical Dish has a turn radius of +/- 35 degrees. If you are mounting the dish on the side of
your house, check the assembled dish and mounting pole to see if you can rotate the dish in the desired
azimuth setting.
If you can’t rotate the dish, choose an alternate location.
Key things to remember when choosing a mounting location:
•
The mounting surface should be flat, even and in good condition.
•
If you install the dish on the roof or side of your house, be sure to attach the bolts into a
building stud, rafter or other solid surface.
•
When mounting on the roof of your house, use an adequate/approved sealant (for your type
of roofing material) around the holes where the base of the universal mount meets the
mounting surface. This will prevent the roof from leaking. Consult with a roofing expert to
confirm best sealant.
4
We do not recommend:
•
Mounting the dish on a railing or fence
•
Installing the dish on aluminum or vinyl siding (these are unlikely to be structurally sound)
•
Mounting the dish on the roof unless absolutely necessary.
Keep grounding requirements in mind (see section 10 for additional information on grounding).
3. Dish Assembly
60cm Dish
1
FIGURE A-60
Step 1 – Assemble Universal Mount
Assembly
NOTE: This step is not required if you will be
Universal
Mount
Assembly
installing your dish on a tripod.
Insert the ½" Carriage Head bolt (1) as shown
in FIGURE A-60, and secure it with a lock nut
Universal
Mount
(2). Repeat for the opposite side. Tighten
2
just enough to hold in place.
1
2a
Step 2 – Assemble Clamp Mount Assembly
(FIGURE B-60)
a. Azimuth Adjustment
Insert the two ¾" Carriage Head
bolts in the top of the Clamp
Mount Assembly. Insert a
FIGURE B-60
Elevation
Adjustment
Azimuth
Adjustment
washer and lock nut on each
bolt. Tighten just enough to hold
2b
in place.
b. Elevation Adjustment
Insert the 3/8" Carriage Head
bolts in the elevation adjustment
area. Insert a lock nut on each
bolt. Tighten just enough to hold
in place.
5
3
Step 3 – Attach the Clamp Mount
Assembly to the 60 cm Elliptical Dish
(FIGURE C-60)
FIGURE C-60
Place the completed Clamp Mount
Assembly on the back of the 60cm Elliptical
dish. When looking at the back of the dish,
Clamp
1 Carriage Head Bolt
(painted head)
Mount
Assembly
2 Flat
Washer
the marked skew adjustment scale should
be on the left.
3 Lock
Insert the two longest (painted head)
Nut
carriage head bolts (1) through the two
holes on the front of the dish.
Secure each bolt with a flat washer (2) and
Dish socket
(bottom of dish)
Centre Pivot Pin
a lock nut (3). Tighten just enough to hold
in place – these will be used for Skew Adjustment.
4
FIGURE F-60
Step 4 – Attach the Satellite Feed Support Arm to the
60 cm Elliptical Dish
Attach the Satellite Feed Support Arm to the 60 cm
Elliptical Dish using the remaining hex head bolt (1), flat
washer (2), plastic spacer (3), and lock nut (4), as shown
in FIGURE F-60. Ensure the slot at the opposite end is on
4 Lock
Dish socket
(bottom of dish)
Nut
the underside of the feed support arm. Tighten fully.
Do not attach the LNB to the Satellite Feed Support Arm
just yet. This will be done later.
3 Plastic
Feed Support Arm
Spacer
1
2 Flat
Washer
Hex Head Bolt
Step 5 – Secure the clamp mount assembly to the 60 cm Elliptical Dish
5
You will use the two remaining hex head Hi/Lo screws in Step 9 on page 11. Do not insert them yet.
6
75cm Dish
1
FIGURE A-75
Step 1 – Assemble Universal Mount
Assembly
NOTE: This step is not required if you will be
2
installing your dish on a tripod.
3
Insert the smallest Carriage Head bolt (1) as
shown in FIGURE A-75, followed by the star
4
washer (2), regular flat washer (3), and lock nut
(4). Repeat for the opposite side. Tighten just
1
enough to hold in place.
2a
Step 2 – Assemble Clamp Mount
Assembly (FIGURE B-75)
c. Azimuth Adjustment
Insert the two largest Carriage
FIGURE B-75
Azimuth
Adjustment
Elevation
Adjustment
Head bolts in the top of the Clamp
Mount Assembly. Insert a washer
and lock nut on each bolt. Tighten
just enough to hold in place.
2b
d. Elevation Adjustment
Insert the remaining Carriage Head
bolts in the elevation adjustment
area. Insert a washer and lock nut
on each bolt. Tighten just enough
to hold in place.
3
FIGURE C-75
Step 3 – Attach the Clamp Mount
Assembly to the 75 cm Elliptical Dish
(FIGURE C-75)
Place the completed Clamp Mount
Assembly on the back of the 75cm
Elliptical dish. Insert the two longer
Plow Bolts through the top holes on the
front of the dish. Insert the two shorter
Plow Bolts through the lower holes on
the front of the dish.
7
Secure each bolt with a skew lock clip, lock washer, and hex nut. Tighten just enough to hold in
place – these will be used for Skew Adjustment.
4
FIGURE F-75
Step 4 – Attach the Satellite Feed Support Arm to the 75 cm
Elliptical Dish
Attach the Satellite Feed Support Arm to the 75 cm Elliptical Dish
using the remaining bolt, plastic spacer, flat washer, and hex nut, as
shown in FIGURE F-75. Ensure the slot at the opposite end is on the
underside of the feed support arm. Tighten fully.
Do not attach the LNB to the Satellite Feed Support Arm just yet.
This will be done later.
Support
Arm Spacer
4. Locating the Satellites
Step 1: Determine the direction in which to point the dish. The first two satellites (SAT A) are located
at 107.3 west longitude; the other satellite (SAT B) is located at 111.1 west longitude. Your xKu LNB
and elliptical dish will be aimed to receive signal from all three satellites.
IMPORTANT: Always use the SAT B Azimuth, Elevation and Skew listings in the Satellite Locator Chart at the
back of this manual for the city nearest your location. This will ensure alignment to all three satellites.
Write them here:
Azimuth
SAT A: ______________________
Elevation
SAT A: ______________________
Skew
SAT A: ______________________
SAT B: ______________________
SAT B: ______________________
SAT B: ______________________
You will adjust the dish as follows to set the azimuth, elevation, and skew:
Azimuth
Elevation
Skew
8
Step 2: At the dish install site, hold a compass
level and still in the palm of your hand. When the
FIGURE G
needle stops rotating (dark half of the needle
always points north), slowly rotate the body of
the compass so that the “N˝ marking is aligned
If you live in
with the dark half of the needle. Locate the tick
Vancouver, the
mark on the compass edge corresponding to the
satellite will be
to the
SAT B azimuth number you wrote down earlier
(see Figure G). This is the direction in which to
point your dish to receive both SAT A and SAT B
signals.
Southeast.
If you live in Newfoundland, the
satellite will be to the Southwest.
TIP: Use a stick or other object to mark the correct azimuth direction.
NOTE: To ensure an accurate compass reading, stay away from large metal objects. To double-check accuracy,
take multiple readings several feet apart.
Step 3: Estimate the SAT B elevation (angle) setting you
recorded earlier, using a protractor if needed (see Figure H).
FIGURE H
Check any obstructions at that elevation. If there are
obstructions, then select an alternate location for the dish.
IMPORTANT: When evaluating the install location, make sure there are
no trees, branches or objects visually obstructing the dish and the
0 degrees is straight
toward the horizon and 90
general direction of the satellite. Also, keep in mind that trees grow up
degrees is straight upward.
and outward and may eventually block the signal.
You have just completed locating a site for your dish.
5. Attaching the Dish
Step 1: Ensure mast is plumb before drilling any holes. Hold the
Universal Mount in place on the mounting area. Use a carpenter’s
level to plumb the antenna mast’s straight section. If the bubble
levels (horizontal and vertical) are not centered, rotate the mast (in
FIGURE I
Level
Not Level
Use bubble level to
plumb mast so it is
vertical in all
directions.
the curved slot) until it is plumb. Lock it in place by securely
tightening the Mast Adjusting Bolts (see Figure I).
IMPORTANT: Alignment of the dish will be difficult if the mast is not
plumb.
Step 2: Drill holes in the structure on which you are mounting the
dish to match the holes in the base of the Universal Mount.
9
Step 3: Secure the Universal Mount with appropriate surface screws. Check the mount for
movement. An improperly secured mount will affect signal reception.
Step 4: Slide the Dish/Clamp Mount Assembly onto the mast by loosening the (2) Azimuth Clamp
Bolts (see Figure B) and the Elevation Pivot Bolt just enough to slide the assembly until it makes
contact with the Elevation Pivot Bolt (see Figure J). Tighten the Elevation Pivot Bolt just enough to
hold it in place on the mast.
FIGURE J
Use the metal edge, not the nut, to set elevation.
(Example: In this picture, the elevation is set at 26.)
Elevation Pivot Bolt
When adjusting elevation, use the
edge of the metal to line up with the
Elevation
elevation setting for your area on the
Adjustment
elevation scale.
Bolt
Elevation
Indicator
Step 5: Loosen the Elevation Adjustment Bolt 1/3 turn from tight on either side of the Clamp Mount
Assembly. Adjust the Clamp Mount Assembly to the edge of the white indicator line per the SAT B
elevation setting you recorded earlier. Tighten the Elevation Adjustment Bolts (see Figure J).
Step 6: Attach the xKu LNB/Feedhorn Clamp Assembly to the Feed Support Arm. Loosen the Feed
Arm screw enough to allow the clamp to fit snugly into the Feed Support Arm. Securely tighten the
Feed Arm screw.
Step 7: Using your compass, point the LNB in the direction
corresponding to the SAT B azimuth setting (see Figure K).
FIGURE K
Draw a vertical mark overlapping the Clamp Mount
Assembly and the mast. This mark will provide you with the
approximate satellite location reference point when you are
ready to tune to the satellite.
Step 8: Loosen the Skew Adjustment Bolts on either side of
the Clamp Mount Assembly. Adjust the Skew Alignment Mark with the scale indicator to the SAT B
skew setting you recorded earlier. Finally, lock it in place by securely tightening the Skew Adjustment
Bolts.
IMPORTANT: Do not make any further adjustments to the Skew Setting from this point onward.
10
Step 9: If you are installing a 60 cm dish, install
the two remaining Hi/Lo hex head screws in
FIGURE L-60
the dish boss holes, shown in Figure L-60. Four
boss holes are available but you'll only need to
use two (the other two may be obstructed
depending on the skew setting). Do not over
tighten the hex head screws.
You have just finished attaching the Dish to the
Boss Holes
Boss Holes
Universal Mount.
6. Connecting the Receiver and Dish
You are now at the point in the installation
where one of the output ports of the xKu LNB needs to be connected to the Shaw Direct satellite
receiver. Connect the receiver to a TV to see a relative scaled signal level meter that will assist you in
obtaining maximum signal strength. If you are unsure of how to connect the TV to the receiver, refer
to the User Guide that came with your receiver.
NOTE: The following instructions apply to the HDDSR 600, HDDSR 605, and/or HDPVR 630 receiver. If you have
a different model satellite receiver, instructions may vary.
Step 1: Connect the RG-6 coaxial cable provided with the install kit to one of the ports of the xKu
LNB. Connect the other end of the coaxial cable to the satellite receiver input connector (If you are
using an HDPVR 630, you must connect two coaxial cables). To make the dish alignment easier, we
suggest you temporarily locate the receiver and TV at an electrical outlet close to where the dish is
installed. Unless you can view the signal level on the TV screen from where the dish is being aligned,
you will require an assistant to monitor the signal level reading on the TV as you align the dish.
Step 2: Tune your satellite receiver to the correct channel to be able to receive signal:
•
If your receiver has never been activated or has been provided as a warranty replacement, it
will be on channel 299. Tune to channel 252.
•
If your receiver has been previous activated, tune to channel 700.
•
If you are using an HDPVR 630 which has never been activated or has been provided as a
warranty replacement, tune to channel 250, and then 252.
•
If you are using an HDPVR 630 which has been activated previously, tune to channel 711, and
then 700.
11
Step 3: Access the Tune in Satellite Signal menu. To access this menu, press OPTIONS on the
remote, followed by the numbers 4, 3, 1. Depending on which version of software is running on your
receiver, the menu will look like the one in
either figure M-1 or M-2
FIGURE M-1 (SD Guide)
The Tune in satellite signal screen will
display the current signal on a scale of 0
(no signal) to 99 (maximum signal). The
objective is to maximize the signal, which
will typically reach up to 98 under ideal
conditions. It is not necessary to enter an
"EMM Provider ID".
You will hear an audio beeping that will
increases and will become a monotone
Signal
Square
once you have reached approximately 50%
FIGURE M-2 (HD Guide)
increase in speed as signal strength
signal strength.
Signal
Strength
IMPORTANT: The audio tone is not available if
your receiver is connected via HDMI.
Always press GO BACK on the remote to exit the
Tune in Satellite Signal screen to prevent loss of
audio when leaving this menu.
Step 4: Verify the connection between the
satellite receiver and the LNB. The square
next to the signal bar should be green. (For
HDPVR 630, both squares should be green).
If the square is red, ensure the RG6 coaxial
Signal
Square
Signal
Strength
cable is securely attached to the correct port on the back of the receiver, and one of the four ports on
the LNB. The square must be green before proceeding.
7. Aligning the Dish to Acquire Shaw Direct Signal
With the receiver on and your assistant ready to monitor signal strength on the TV, you are now
ready to make adjustments to the dish to acquire the Shaw Direct satellite signal. If you are using a
satellite finder, please refer to the instructions in Section 9.
Step 1: Refer to the azimuth, elevation and skew settings for the location that you recorded on Page
8.
12
Step 2: Check that the dish skew is set to
the skew setting listed for your area. The
skew alignment mark is shown in Figure N.
FIGURE N
Use the skew adjustment mark, not the nut, to set skew.
(Example: In this picture, the skew is set at 100.)
Step 3: Check that the dish elevation is set
to the elevation setting listed for your area.
Step 4: Draw a reference mark on the dish
clamp and pipe mast as a starting point
before you make any adjustments to the
dish.
Step 5: Standing behind the dish, using
both hands, grasp the dish on each side
Skew
Adjustment
Mark
and move it so that it points all the way
west. Then, slowly move the dish in very small increments to the east while your assistant observes
the TV installation menu for increases in signal strength.
Step 6: As you start to get an indication of increasing signal, make a second reference mark on the
dish clamp and pipe mast to serve as a point where signal strength increased.
Step 7: As you move the dish past the point of maximum signal strength, move the dish back in the
opposite direction until you achieve maximum signal.
Step 8: Tighten the dish clamp screws.
Step 9: Now make small adjustments to the elevation of the dish to see if you can further improve on
the signal strength. Loosen the Elevation Adjustment Bolts and make slight adjustments (1/2 degree
increments) in the elevation, finding the maximum signal strength. When you’ve located the
maximum signal strength possible, securely tighten all bolts.
NOTE: Do not be discouraged if you do not acquire signal on your first attempt. Be patient and try again.
Recheck the pipe mast for true vertical 90 degrees. Once you acquire signal, you may need to make very small
adjustments to the dish compass heading (azimuth), elevation and skew settings to maximize signal strength
above 80.
Authorizing Receiver for Service
If your receiver installer menu displays signal strength above 80, you have successfully aligned the
dish to the Shaw Direct satellite.
You are now ready to authorize your receiver for programming.
13
8. Activation and Fine Tuning
Step 1: Call Shaw Direct at 1.888.554.7827 to authorize your receiver for programming.
Shaw Direct will ensure the correct channel map is set for your receiver and verify the reception of
each satellite. After your receiver has been activated, you can fine tune the dish to ensure maximum
signal strength on all channels.
While speaking with the Shaw Direct representative, ask for a reference channel from each satellite
to use when fine tuning the dish.
Step 2: Tune to the first reference channel provided and access the Tune in Satellite Signal menu as
described in Section 6.
Fine tuning the Azimuth:
Step 3: With your assistant monitoring the signal level, move the dish back and forth slightly (about a
millimeter at a time) to attempt to acquire the highest reading possible on the signal strength meter.
Step 4: Once you have found the maximum signal strength, lock the azimuth rotation position in
place by tightening the Azimuth Clamp Bolts (see Figure B).
NOTE: Fine tuning to the highest signal strength possible reduces signal interference in adverse weather
conditions and ensures optimal reception from all satellites.
Fine tuning the Elevation:
Step 5: Loosen the Elevation Adjustment Bolts and make slight adjustments (1/2 degree increments)
in the elevation, finding the maximum signal strength, as you did in the azimuth tuning process.
Step 6: Exit the Tune in Satellite Signal menu and tune to the second reference channel provided. Go
back into the Tune in Satellite Signal menu and repeat steps 3-5 to maximize signal strength from
the second satellite. (If your receiver is running the HD Guide, it is not necessary to exit the screen –
you can change channels from within the Tune In Satellite Signal menu.)
Step 7: When you’ve located the highest signal possible on both channels, securely tighten all bolts.
YOU HAVE JUST COMPLETED FINE TUNING. Skip ahead to section 10.
14
9. Alternate Tuning Method
You may prefer to locate the satellites using a SF-100 Satellite
FIGURE O
Finder (see Figure O), a standalone satellite signal finding meter
which can be purchased separately from Shaw Direct or your Shaw
Direct retailer.
Step 1: Connect a short coaxial cable from the LNB terminal on the
Satellite Finder to the xKu LNB. Connect the receiver terminal on
the meter to a coaxial cable, which in turn connects to the SAT IN
port on the Shaw Direct receiver.
Step 2: Tune to the channel advised in Section 6.
NOTE: For the satellite finder and LNB to function, they must be connected to a satellite receiver that is plugged
in and turned on.
Step 3: Adjust the dish as closely as possible to the elevation and azimuth settings you recorded
earlier.
Step 4: Move the dish azimuth rotation very slightly to the right of the reference mark you drew on
page 8.
Step 5: Slowly rotate the dish back toward the reference mark and listen for pitch changes in the
audible tone. If your elevation is set correctly, you should hear two major pitch changes as it picks up
the satellite signals. A weak first change of pitch may be the wrong satellite. Continue rotating the
dish until the second major deflection, which will be SAT A (107.3), your intended target.
Step 6: When you have located both signals, move the dish slightly to the right and left of the mark
until you’ve maximized the signal. Then tighten the Azimuth Clamp Bolts. Verify you’ve located the
correct satellite by confirming signal strength on the satellite receiver (see page 12).
Step 7: While listening to the meter, apply gentle pressure to the top of the dish to move the dish –
first slightly downward, then upward to see if you can increase the signal strength further. Carefully
adjust the elevation until you’ve maximized the signal. Tighten the Elevation Adjustment Bolts.
Step 8: Follow the steps described in Fine Tuning (Section 8) to obtain the highest reading possible
on the signal strength meter.
Step 9: The dish should now be peaked to its maximum. Remove the Satellite Finder and plug the
LNB directly into the receiver. Confirm the signal strength by checking the on-screen signal strength
meter, as described in Section 6.
Your system is now fine tuned.
15
10. Grounding the Coaxial Cable
FIGURE P
The Shaw Direct Self Install kit includes the following items to ground
the outdoor coaxial cable:
•
Dual Coax Cable Grounding Block
•
Grounding Wire
Outdoor coaxial cable that may be subject to static discharge or
contact with electrical wiring must be grounded through a grounding
block located as close as possible to the cable entry point (see Figure
P).
Step 1: Attach the grounding block to the side of your home, close to
the coaxial cable entry point. Connect the coaxial cable(s) running
from the dish, and to the receiver(s).
Step 2: Attach the ground wire to the grounding block connector and
tighten the screw.
Step 3: Attach the grounding wire from the
grounding block connector to the central building
Grounding
Block
FIGURE Q
ground or another approved grounding point.
Acceptable grounding points may include a ground
rod, metal electrical service panel, or copper cold
water pipe within five feet of the entrance to the
structure. Examples are shown in Figure Q.
Grounding
Block
IMPORTANT: Always refer to your regional electrical
code and/or contact a licensed electrician if you are
Grounding
Wire
unsure about your local grounding requirements.
IMPORTANT: For more information on grounding, refer to
the receiver’s User Guide included with your Shaw Direct
Grounding
Location
system.
11. Troubleshooting
If you are having trouble finding the satellite signal, try each of the following:
•
You must be tuned to a valid channel in order to align the dish. Review section 6 for the
channels to use with the xKu LNB. If you do not have an xKu LNB, try aligning the dish on
channel 299.
16
•
The cable can be plugged into any of the four (4) available ports on the xKu LNB, but must be
plugged into the SAT IN port on the Shaw Direct receiver. If you have an HDPVR 630, two (2)
cables must be connected to the SAT 1 and SAT 2 ports.
•
Make sure all cables are secure and re-verify your azimuth, elevation and skew setting for
your location. The settings straight section must be plumb.
•
Adjust the elevation by +1 degree from the settings you recorder earlier and repeat the steps
in Section 7 to acquire Shaw Direct signal.
•
Adjust the elevation by –1 degree from your original settings you recorded earlier and repeat
the steps in Section 7 to acquire Shaw Direct signal.
•
Ensure cables are connected properly at the grounding block.
If you still can’t select or acquire signal, call us at 1.888.554.7827 for further assistance.
12. Satellite Locator Chart
Satellite coordinates are provided on the next page for both Satellite A (107.3W longitude) and
Satellite B (111.1W longitude.) The reception of satellite signals in areas with a dish elevation less
than 12 degrees may not be possible. Consult with a Shaw Direct retailer in your area. All
information is listed in degrees.
Note: Please refer to the SATELLITE B settings if you have an elliptical dish. Satellite A should only be used for
a round dish.
Online Satellite Location
If you have access to a computer, exact dish coordinates can also be obtained at
www.dishpointer.com. Enter your current address and then select “111.1W ANIK F2” as the satellite.
For the “LNB Skew” listed online, add 90 degrees for equivalent settings. For example, an LNB skew
listed online as “-5.0°” is 85 degrees. An LNB skew listed online as “30.0°” is 120 degrees.
17
Satellite A
Compass
Azimuth
Azimut –
Coord.
magn.
Newfoundland / Terre-Neuve
Satellite B
Dish
Elevation
Dish
Skew
Compass
Azimuth
Élévation
Inclinaison
Satellite A
Dish
Elevation
Dish
Skew
Compass
Azimuth
Azimut –
Coord.
magn.
Élévation
Inclinaison
Azimut –
Coord.
magn.
Bonavista
Cartwright
Corner Brook
Gander
Grand Falls
Hebron
Indian Harbour
Labrador City
Nain
North West River
Nutak
Placentia
Port aux Basques
Rigolet
Schefferville
St. Anthony
St. John’s
Trepassey
Wabush City
264
262
260
263
262
259
262
251
258
259
259
263
258
261
251
262
264
263
251
14.4
13.8
17
15
15.7
13.6
13.6
19.1
14.4
15.5
13.8
15.5
18.5
14.3
17.8
14.4
14.6
15.4
19
126
120
124
125
125
114
119
116
116
119
115
127
125
119
115
122
127
128
116
267
265
263
266
265
262
265
254
262
262
262
266
262
264
255
266
267
267
254
12.1
11.9
14.8
12.8
13.5
12
11.7
17.3
12.7
13.6
12.2
13.2
16.2
12.4
16.1
12.3
12.3
13.1
17.2
127
121
125
126
126
115
120
118
117
120
116
128
126
120
116
124
128
129
118
Bridgewater
Cape Breton Is.
Chesterfield In.
Dartmouth
Freeport
Mulgrave
Port Hawkesbury
Port Maitland
Sable Is.
Shelburne
Sydney
Truro
Wedgeport
Yarmouth
252
256
208
254
250
256
256
250
258
251
257
254
250
250
23.7
20.5
17.5
22.9
24.8
21
21
24.9
21.1
24.6
19.9
22.3
25
25
125
125
98
125
124
125
125
125
128
125
125
125
125
125
256
260
212
257
254
259
260
254
261
255
261
257
254
254
21.3
18.2
16.9
20.6
22.5
18.6
18.6
22.5
18.6
22.2
17.6
20
22.6
22.7
127
127
100
127
126
127
127
127
129
127
127
126
127
127
Charlottetown
254
21.7
124
258
19.4
126
Bath
Bathurst
Chatham
Dalhousie
Edmundston
Fredericton
Grand Manan Is.
Hartland
Kedgwick
Moncton
Napadogan
Newcastle
Oromocto
Plaster Rock
St. John
248
251
251
250
247
250
249
248
249
252
249
251
250
249
250
24
22.2
22.5
22.3
23.8
23.9
24.9
24.1
23.1
22.7
23.8
22.6
23.9
23.6
24
122
122
122
121
120
123
124
122
121
123
122
122
123
121
123
252
255
255
254
251
253
253
252
252
256
253
255
253
252
254
21.9
20.1
20.3
20.2
21.7
21.7
22.6
22
21
20.5
21.6
20.4
21.6
21.5
21.7
123
123
124
123
122
124
126
124
123
125
124
124
125
123
125
Alma
Amos
Anticosti
Asbestos
Baie Comeau
Baie St.Paul
Asbestos
242
231
254
242
248
244
242
24.7
27.6
19.6
26.9
22.4
24.9
26.9
118
114
121
120
119
119
120
246
235
258
246
251
248
246
22.7
25.9
17.5
24.9
20.4
22.9
24.9
120
116
123
122
121
121
122
Nova Scotia / Nouvelle-Écosse
Prince Edward Island / Ile-du-Prince-Édouard
New Brunswick / Nouveau-Brunswick
Québec
Beattyville
Cap-de- la-Madeleine
Charlesbourg
Chibougamau
Chicoutimi
Cowansville
Dolbeau
Donnacona
Dosquet
Drummondville
Eastmain
Festubert
Fort Coulonge
Gagnon
Gaspe
Gatineau
Granby
Grand Mere
Hauterive
Hull
Inukjuak
Ivujivik
Joliette
Kuujjuaq
Kuujjuarapik
La Sarre
La Tuque
Levis
Madeleine
Malartic
Maniwaki
Matagami
Matane
Mingan
Miquelon
Mistassini
Monet
Mont Laurier
Mont Louis
Montmagny
Montreal
Mont Joli
Natashquan
Noranda
Parent
Paspebiac
Pointe aux Anglais
Pointe-aux-Tremble
Port Cartier
Quaqtaq
Quebec
Rimouski
Riviere-du-Loup
RivierePentecote
Roberval
Rouyn
Salluit
Senneterre
Sept Iles
Shawinigan
Sheldrake
232
241
243
238
243
240
241
242
242
241
231
240
233
248
253
235
240
241
248
235
235
240
239
252
234
228
240
243
256
230
235
232
249
253
234
241
235
235
251
244
239
247
256
229
237
251
249
239
250
253
243
247
245
249
241
229
244
232
250
240
252
Satellite B
Dish
Elevation
Dish
Skew
Compass
Azimuth
Dish
Elevation
Dish
Skew
Élévation
Inclinaison
Azimut –
Coord.
magn.
Élévation
Inclinaison
26.9
26.8
25.7
24.9
24.4
27.8
24.7
26.1
26.2
27.1
24.5
26.2
29.3
20.4
20.7
29.1
27.6
25.1
22.5
29.1
19
15.4
27.5
15.8
21.5
27.8
26.1
25.7
20.1
28
28.5
26.5
22.3
19.5
26.2
24.6
26.8
28.1
21.1
25.3
28
22.9
18.4
28.2
26.6
21.7
21.6
27.8
21.2
14.1
25.8
23.1
24.1
21.5
25
28.2
15
27.3
20.8
26.7
20
114
119
119
115
118
120
117
119
119
119
111
118
117
117
121
118
120
117
119
118
107
105
119
112
109
113
118
119
124
114
117
113
120
120
114
117
115
117
120
120
119
119
121
113
116
121
119
119
119
109
119
119
119
119
117
113
106
114
119
119
120
237
245
247
242
247
244
245
246
246
245
235
244
237
252
256
239
244
245
251
239
239
244
243
256
238
233
244
247
259
235
239
236
252
257
238
245
239
239
255
248
243
251
260
233
241
255
253
243
253
256
247
251
249
253
245
233
248
236
254
244
256
25.2
24.7
23.7
23.1
22.5
25.7
22.8
24.1
24.1
25.1
23
24.2
27.4
18.6
18.6
27.1
25.6
23.2
20.5
27.2
17.8
14.4
25.5
14.4
20.1
26.2
24.1
23.7
17.8
26.2
26.6
24.8
20.3
17.5
24.5
22.8
25
26.2
19.1
23.2
26
20.9
16.3
26.5
24.7
19.6
19.6
25.8
19.2
12.8
23.7
21.1
22.1
19.5
23.1
26.5
14
25.6
18.8
24.7
18
116
121
121
117
120
122
119
121
121
121
113
120
119
118
123
120
122
119
121
120
109
106
121
113
111
115
120
121
125
116
119
115
121
122
116
119
118
119
122
122
121
121
123
116
119
123
121
121
121
110
121
121
121
121
119
116
107
117
121
121
121
18
Satellite A
Compass
Azimuth
Sherbrooke
Sorel
St. Paul du Nord
St. Agathe-des-Monts
St. Agapit
St. Anne de Beaupre
St. Augustin
St. Boniface
St. Eloi
St. Hyacinthe
St. Jean
St. Jerome
St. Jean de Matha
St. Laurent
St. Pacome
St. Pascal
St. Simeon
St. Stephen
Tadoussac
Trois-Rivieres
Val d’Or
Valleyfield
Vandry
Verdun
Victoriaville
Waskaganish
Wemindji
Windsor
Ontario
Apsley
Arnprior
Bancroft
Barrie
Belleville
Blind River
Bracebridge
Bradford
Brampton
Brockville
Burlington
Carleton Place
Chapleau
Chatham
Cobalt
Cobourg
Cochrane
Collingwood
Cornwall
Dalton
Deep River
Dryden
Elliot Lake
Emsdale
English River
Espanola
Foleyet
Fort Albany
Fort Frances
Fort Severn
Gananoque
Geraldton
Satellite B
Dish
Elevation
Dish
Skew
Compass
Azimuth
Azimut –
Coord.
magn.
Élévation
Inclinaison
231
234
231
227
232
220
228
228
227
235
227
234
220
223
227
230
225
226
237
218
232
198
221
228
202
223
222
224
197
212
234
212
30.8
29.4
30.5
31.9
31
31.6
31.2
32.1
32.6
29.8
32.9
29.6
30.4
34.8
29.3
31.6
28.3
32.1
29
30.3
29.4
31.1
31.3
30.7
31.4
31.2
29.8
25.6
32.6
23.8
30.2
29.8
116
117
116
116
117
112
115
116
116
118
116
117
110
115
113
117
111
115
119
110
116
102
112
115
104
113
111
109
102
103
118
107
242
240
246
238
242
243
259
188
246
240
239
238
239
239
245
245
245
249
245
241
231
238
239
239
242
230
231
241
27.2
27.3
23.5
27.9
26
25.5
16.1
32
23.8
27.6
28
28
27.4
28
24.7
24.5
24.3
24.8
24
26.8
27.8
28.5
26.1
28
26.7
25.3
24
27.1
120
119
119
118
119
119
121
99
119
119
119
118
118
119
119
119
119
123
119
119
114
119
117
119
119
111
110
120
Satellite A
Dish
Elevation
Dish
Skew
Compass
Azimuth
Azimut –
Coord.
magn.
Élévation
Inclinaison
Azimut –
Coord.
magn.
235
238
235
232
236
225
232
232
232
239
232
238
224
227
232
235
229
231
241
223
236
203
226
232
207
227
226
229
202
216
238
216
28.9
27.5
28.6
30
29
30
29.3
30.2
30.7
27.8
31
27.6
28.9
33
27.6
29.6
26.8
30.2
26.9
28.8
27.6
30.3
29.7
28.9
30.3
29.5
28.2
24.3
31.6
22.9
28.2
28.5
119
120
119
118
120
115
118
119
119
121
119
120
113
118
116
120
114
118
121
112
118
105
115
118
107
115
114
111
105
105
121
109
246
244
250
242
246
247
263
193
250
244
243
242
243
243
249
249
249
252
249
245
235
242
243
243
246
234
235
245
25.1
25.3
21.5
26
24
23.4
14.1
31.3
21.8
25.5
25.9
26
25.4
26
22.6
22.4
22.3
22.5
22
24.8
26.1
26.4
24.2
26
24.6
23.8
22.5
25
122
121
121
120
121
121
123
102
121
121
122
121
121
121
121
121
121
125
121
121
116
121
119
121
122
113
112
122
Gilmour
Goderich
Gogama
Gravenhurst
Guelph
Haliburton
Hamilton
Hanover
Hearst
Hornepayne
Huntsville
Ignace
Ingersoll
Iroquois Falls
Kapuskasing
Kenora
Kincardine
Kingston
Kirkland Lake
Kitchener
Lindsay
Little Current
London
Longlac
Lynx
Macdiarmid
Madoc
Magog
Manitoulin I.
Matachewan
Mattawa
Mattice
Mekatina
Michipicoten
Midland
Milne Inlet
Mobert
Moosonee
Nakina
New Liskeard
Newcastle
Nipigon
North Bay
Oakville
Oba
Opasatika
Orillia
Oshawa
Ottawa
Ottawa Is.
Oulmet
Owen Sound
Pagwa River
Parry Is.
Parry Sound
Pembroke
Penetanguishene
Perth
Petawawa
Peterborough
Pickle Crow
231
223
223
229
226
231
227
225
219
217
228
201
225
225
222
194
223
234
227
226
229
223
224
213
214
209
232
241
221
225
229
220
218
216
227
259
215
226
212
227
230
209
228
227
218
221
228
229
235
233
208
225
216
194
227
232
227
234
232
230
205
Satellite B
Dish
Elevation
Dish
Skew
Compass
Azimuth
Dish
Elevation
Dish
Skew
Élévation
Inclinaison
Azimut –
Coord.
magn.
Élévation
Inclinaison
30.6
33.4
29.9
31.1
32.9
30.6
33
32.7
28.7
29.5
30.9
31.4
33.7
28.4
28.5
31.6
33
30.5
28.7
33.1
31.5
31.5
33.9
29.5
29.1
30.4
30.8
27.4
31.9
29.2
29.8
28.7
31.4
30.8
31.7
7.1
30.4
26.2
29.2
29.2
31.8
30.9
30.1
32.7
29.5
28.6
31.6
31.9
29.1
18.3
31.2
32.3
28.9
5.4
31.2
29.5
31.7
29.8
29.5
31.3
28.9
117
115
112
116
116
116
116
115
109
108
115
103
116
112
110
101
114
118
113
116
116
113
115
107
107
106
117
120
112
112
115
109
110
109
115
98
108
110
107
113
117
106
114
116
109
110
116
117
118
105
106
114
108
91
115
116
115
118
116
117
103
236
228
228
233
231
235
232
229
224
221
233
205
230
230
226
199
228
238
231
230
234
227
229
218
218
214
236
245
226
230
234
224
223
221
231
263
219
230
217
232
234
213
232
232
223
225
232
233
239
237
213
229
220
198
231
237
231
238
236
234
209
28.7
31.6
28.3
29.3
31
28.7
31.1
30.9
27.3
28.2
29.1
30.3
31.8
26.9
27.1
30.7
31.2
28.5
27.1
31.2
29.6
29.8
32
28.3
27.8
29.2
28.8
25.3
30.3
27.6
28
27.2
29.9
29.4
29.9
6.6
29
24.7
28
27.5
29.9
29.7
28.4
30.8
28.1
27.1
29.7
30
27.2
17.2
30
30.5
27.6
5.3
29.4
27.6
29.9
27.9
27.6
29.4
27.8
119
117
114
118
119
119
119
118
112
111
118
106
119
114
113
104
117
121
115
119
119
115
118
110
110
109
120
122
115
115
117
112
113
112
118
99
111
112
109
116
119
109
117
119
112
112
118
119
120
107
109
117
110
92
117
119
118
120
119
119
106
19
Satellite A
Compass
Azimuth
Picton
Port Nelson
Port Stanley
Ramore
Red Lake
Renfrew
Richmond Hill
Sand Lake
Sarnia
Sault Ste Marie
Savant Lake
Schreiber
Simcoe
Sioux Lookout
Smiths Falls
Steep Rock Lake
St. Catharines
St. Thomas
Stokes Bay
Stratford
Sturgeon FaIIs
Sudbury
Sultan
Swastika
Tannin
Temiscaming
Thessalon
Thetford Mines
Thunder Bay
Timmins
Tionaga
Tobermory
Toronto
Trenton
Trout Creek
Wallaceburg
Waterloo
Welland
Whitby
Whitney
Windsor
Wingham
Winisk
Woodstock
Manitoba
Brandon
Dauphin
Emerson
Flin Flon
Gimli
Grand Rapids
Gypsumville
Hodgson
Lynn Lake
Minnedosa
Morden
Portage la Prairie
Norway House
The Pas
Thompson
Winnipeg
Azimut –
Coord.
magn.
232
200
224
226
196
233
228
217
222
217
203
211
226
200
234
201
228
224
224
225
227
225
221
227
202
229
219
243
206
224
222
223
228
232
228
222
226
228
229
230
221
224
217
225
182
181
188
177
188
183
185
187
179
182
186
185
186
178
186
188
Satellite B
Dish
Elevation
Dish
Skew
Compass
Azimuth
Élévation
Inclinaison
Azimut –
Coord.
magn.
31
23.7
34.1
28.6
30.2
29.6
32.2
30.8
34.4
31.9
30.2
30.8
33.6
30.7
29.7
32
32.8
34
32.2
33.4
30.3
30.6
30.3
28.8
31
29.6
31.8
26.3
31.7
29
29.6
32
32.4
31.1
30.4
34.7
33.1
32.9
32
30.3
35.3
33.1
23.9
33.5
32.4
31
32.9
27.3
31.2
28.8
30.2
30.6
25
32
32.8
32.1
27.8
28.3
25.9
32
118
99
116
112
101
117
116
110
115
111
104
107
116
103
118
103
117
116
114
115
114
113
111
113
104
114
111
120
106
111
111
113
116
117
115
115
116
117
117
116
115
115
105
116
96
96
99
94
98
96
97
98
94
96
98
98
97
94
97
99
237
204
229
230
201
237
232
222
227
222
208
215
231
205
239
206
233
229
228
229
231
229
225
231
207
233
224
247
211
228
227
228
232
236
232
227
230
233
233
234
225
229
222
230
187
186
193
182
193
188
189
192
183
187
191
190
191
183
191
193
Satellite A
Dish
Elevation
Dish
Skew
Compass
Azimuth
Élévation
Inclinaison
29
22.9
32.3
27
29.3
27.6
30.3
29.4
32.6
30.4
29.1
29.5
31.6
29.7
27.7
30.9
30.8
32.2
30.4
31.5
28.5
28.9
28.8
27.2
29.9
27.9
30.2
24.3
30.5
27.4
28.1
30.3
30.5
29.2
28.6
32.9
31.2
31
30.1
28.4
33.5
31.3
22.8
31.6
31.9
30.5
32.2
26.9
30.5
28.3
29.6
30
24.7
31.4
32.2
31.4
27.2
27.9
25.3
31.3
120
102
119
115
104
119
119
112
118
113
106
110
119
106
120
106
120
119
117
118
117
116
114
115
106
117
114
122
108
114
114
116
119
120
117
118
118
120
119
118
118
118
107
119
99
99
102
97
101
99
100
101
97
99
101
101
100
97
99
102
Satellite B
Dish
Elevation
Dish
Skew
Compass
Azimuth
Dish
Elevation
Dish
Skew
Azimut –
Coord.
magn.
Élévation
Inclinaison
Azimut –
Coord.
magn.
Élévation
Inclinaison
Assiniboia
Beauval
Biggar
Estevan
Fond du Lac
Kamsack
La Ronge
Lloydminster
Maple Creek
Melfort
Moose Jaw
Nokomis
North Battleford
Regina
Rosetown
Rosthern
Saskatoon
Shaunavon
Sherridon
Stanley
Swift Current
Tisdale
Uranium City
Watrous
Weyburn
Wilkie
Yorkton
169
165
165
175
164
177
169
161
162
171
170
171
164
172
165
168
167
165
178
170
166
173
161
170
174
163
176
33.1
27.1
30.4
33.5
22.6
30.8
27.1
29.1
32.7
29.5
32.2
31
29.7
32.1
31
29.8
30.3
33
24.8
26.4
32.4
29.5
22.4
30.8
32.9
30
31.2
91
90
90
94
90
94
91
88
88
92
91
92
89
92
90
91
91
89
94
92
90
93
89
91
93
89
94
174
169
170
180
168
182
174
165
167
176
175
176
169
177
170
173
172
169
183
175
170
177
165
175
179
168
181
32.9
27
30.4
33.1
22.6
30.4
26.9
29.1
32.8
29.3
32
30.8
29.6
31.8
30.9
29.6
30.2
33
24.4
26.2
32.3
29.2
22.4
30.6
32.6
30
30.8
94
93
92
97
92
97
94
91
91
95
95
95
92
95
93
94
94
92
97
94
93
95
91
95
96
92
97
Athabasca
Banff
Bassano
Brooks
Calgary
Camrose
Cranbrook
Drumheller
Edmonton
Edson
Fort Chipewyan
Fort MacKay
Fort McMurray
Fort Vermilion
Grande Prairie
Hanna
Hines Creek
Jasper
Lac Ia Biche
Lacombe
Leduc
Lethbridge
McLennan
Meander River
Medicine Hat
Peace River
Red Deer
Stettler
Vegreville
Vegreville
Vermilion
154
151
157
158
154
156
151
156
154
149
156
156
157
148
145
158
145
147
156
154
154
156
148
145
160
147
154
156
157
157
159
27.3
30.9
31.6
31.9
31.2
29.2
32.7
30.9
28.6
28.2
23.2
24.8
25.3
23.2
26.2
30.8
25.1
28.7
27.4
29.7
28.9
32.8
25.9
22.4
32.5
25.3
29.9
29.9
28.7
28.7
29
86
83
86
86
85
86
83
86
86
83
88
87
87
85
82
86
83
82
87
85
85
85
83
84
87
83
85
86
87
87
87
159
156
162
163
159
160
156
161
159
154
161
160
161
152
149
162
149
151
161
159
159
161
152
149
165
151
159
161
161
161
164
27.5
31.3
31.8
32
31.4
29.4
33.1
31.1
28.8
28.6
23.2
24.9
25.4
23.5
26.7
30.9
25.6
29.2
27.5
30
29.1
33
26.3
22.7
32.6
25.7
30.2
30.1
28.9
28.9
29.1
89
86
89
89
88
89
86
89
88
86
90
90
90
87
85
89
85
85
89
88
88
89
86
86
90
86
88
89
89
89
90
York Factory
Saskatchewan
Alberta
200
23.7
100
204
22.9
102
20
Satellite A
Compass
Azimuth
Wetaskiwin
Azimut –
Coord.
magn.
155
Satellite B
Dish
Elevation
Dish
Skew
Compass
Azimuth
Élévation
Inclinaison
29.2
85
British Columbia / Colombie-Britannique
Satellite A
Dish
Elevation
Dish
Skew
Compass
Azimuth
Azimut –
Coord.
magn.
Élévation
Inclinaison
Azimut –
Coord.
magn.
159
29.4
88
Ashcroft
Atlin
Chemainus
Courtenay
Dawson Creek
Duncan
Esquimalt
Fort Grahame
Fort Nelson
Ft St. John
Hazelton
Hudson Hope
Kamloops
Kelowna
Kitimat
Ladysmith
Lillooet
McLeod Lake
Nanaimo
Nelson
New Westminster
Penticton
Port Alice
Port Renfrew
Prince George
Prince Rupert
Quesnel
Queen Charlotte Is.
Revelstoke
Saanich
Sidney
Simoom Sound
Squamish
Stewart
Telegraph Creek
Trail
Vancouver Is.
Vancouver
Vernon
Victoria Beach
Victoria
Williams Lake
142
125
139
137
142
139
140
136
138
141
133
140
144
145
132
139
141
139
139
149
140
145
134
138
139
130
140
127
147
140
140
135
140
130
128
148
136
140
146
189
140
141
30.4
18.7
31.7
30.6
25.4
31.9
32.2
23.9
21.9
24.8
24.5
24.8
30.7
31.7
25.3
31.6
30.3
25.7
31.4
32.4
31.6
32
29.2
31.9
26.8
24.7
27.8
25.1
30.7
32.2
32
29
31
23.1
20.9
32.8
30
31.5
31.3
31
32.3
28.8
79
75
76
75
81
76
76
79
81
81
77
80
79
80
75
76
78
79
76
82
77
80
74
75
79
74
79
72
81
76
76
75
77
75
76
81
75
77
80
99
76
79
147
129
144
142
147
144
145
141
142
146
137
144
149
150
136
144
146
143
144
154
145
150
139
143
144
134
145
132
152
145
145
139
145
134
132
153
141
145
150
194
145
146
31.1
19.7
32.5
31.5
26
32.7
33.1
24.6
22.5
25.4
25.3
25.4
31.3
32.3
26.2
32.5
31
26.4
32.3
32.9
32.4
32.7
30.2
32.9
27.5
25.7
28.5
26.3
31.2
33.1
32.9
30
31.9
24.1
21.8
33.4
30.9
32.4
31.9
30.3
33.1
29.5
82
77
79
78
84
79
79
81
83
83
79
83
82
83
78
79
81
82
79
85
80
83
77
79
82
77
82
75
84
79
79
78
80
78
78
84
78
80
83
102
79
82
Amadjuak
Arctic Bay
Bathurst Inlet
Bathurst Is.
Cambridge Bay
Cape Dyer
Cornwallis Is.
Devon Is.
Eskimo Point
Frobisher Bay
Gjoa Haven
Igloolik Is
Kangirsuk
Lake Harbour
Mackenzie King Is.
Padlei
252
253
158
211
165
268
233
261
197
257
198
247
251
254
134
190
12.8
7.1
14.8
5.4
12.4
7.6
6.1
5.4
19.8
11.7
12.5
10.3
15
12.8
4
19.3
106
97
90
92
91
108
93
96
97
107
94
100
110
108
89
96
255
257
162
215
169
272
237
265
201
261
202
251
255
258
138
194
11.7
6.7
14.8
5.2
12.3
6.4
5.9
5
19.3
10.5
12.2
9.6
13.7
11.6
4
18.8
107
98
91
93
92
109
94
97
99
109
96
101
111
109
90
98
Nunavut
Padloping Is
Pangnirtung
Pelly Bay
Qurlurtuuq
Rankin Inlet
Repulse Bay
Resolute
Resolution Is.
Somerset Is.
Southampton Is.
Spence Bay
Tavani
Wager Bay
Whale Cove
268
264
223
142
205
228
231
259
226
230
212
200
213
201
Satellite B
Dish
Elevation
Dish
Skew
Compass
Azimuth
Dish
Elevation
Dish
Skew
Élévation
Inclinaison
Azimut –
Coord.
magn.
Élévation
Inclinaison
7.7
9.2
11.9
13.6
17.8
13.4
6.5
12.2
8
14.9
11.4
18.9
14.7
18.3
107
107
97
87
98
99
93
110
94
101
95
97
97
97
271
267
227
146
209
232
235
263
230
234
216
204
217
206
Northwest Territory / Territories du Nord-Ouest
6.6
8
11.4
13.7
17.2
12.7
6.2
10.9
7.7
14.2
11
18.3
14.1
17.8
108
108
98
88
100
100
94
112
95
102
97
99
99
99
Arctic RedRiver
Banks Is.
Fort Franklin
Fort Good Hope
Fort Liard
Fort Norman
Fort Reliance
Fort Simpson
Fort Smith
Ft McPherson
Ft Providence
Ft Resolution
Hay River
Holman Island
Inuvik
Jean Marie Rvr
Melville Is.
Nahanni Butte
Norman Wells
Port Radium
Rae
Snowdrift
Tuktoyaktuk
Victoria Is.
Wrigley
Yellowknife
120
126
132
126
136
130
158
138
154
120
143
150
147
135
120
139
144
135
129
139
145
155
120
149
134
148
11.6
7.9
15.3
13.6
20.3
15.4
19
19.1
21.8
11.4
20
20.5
20.7
10.5
10.9
19.4
6
19.5
14.8
15.1
18.6
19.4
10
10.5
17.3
19
79
86
83
81
81
82
89
83
87
79
84
87
85
86
80
83
89
81
81
85
86
88
81
89
82
86
124
130
136
130
140
134
162
142
159
124
148
155
151
139
124
143
148
140
133
143
149
159
124
154
138
152
12.3
8.2
15.8
14.2
20.9
15.9
19
19.6
21.9
12.1
20.3
20.7
20.9
10.7
11.5
19.9
6
20
15.3
15.3
18.8
19.4
10.5
10.5
17.8
19.2
81
87
84
82
83
83
91
85
90
80
86
89
87
88
81
85
90
83
83
87
87
90
82
90
84
88
Big Salmon
Carmacks
Dawson
Forty Mile
Keno Hill
Klondike
Mayo Landing
Old Crow
Stewart River
Tagish
Teslin
Watson Lake
Whitehorse
122
121
118
117
121
118
121
116
118
124
125
129
123
16.3
15.8
13.3
12.8
14.4
13.4
14.5
10.3
14
17.9
18.5
19.4
17.4
76
75
75
75
77
75
77
77
75
75
76
78
75
127
125
122
121
125
122
125
120
122
128
129
134
127
17.2
16.7
14.3
13.7
15.2
14.3
15.3
11.1
14.9
18.9
19.3
20.2
18.3
78
77
77
77
79
77
78
79
76
77
78
80
77
Prince Charles Is.
Prince of Wales Is.
Prince Patrick Is.
Queen Elizabeth Is
254
197
121
256
10.3
8.3
4.2
2.9
102
93
87
92
258
201
125
259
9.5
8.1
4.3
2.8
103
94
88
93
Yukon Territory
Canadian Arctic Islands / Archipel Arctique Canadien
21