docOmvivo - Bathroom basins
download 
Report Transcription
Omvivo - Bathroom basins
Product Specification Catalogue – Edition 3 edition three 1 ‘The Omvivo Collection incorporates pieces that challenge our perceptions and inspire our senses. It is a collection of classical bathroom and living pieces, created by hand using the finest of materials. While produced for everyday use, Omvivo creates for longevity, with a consideration and appreciation for the environment. These designs reflect an intrinsic desire to create water efficient and environmentally responsible products. From the meditative waterfall like qualities of the Le Cob Bath to the timeless Washplane® collection, the products are truly unique, displaying a persistent commitment to innovative design. Omvivo endeavors to collaborate with the best of Australian design to consistently produce distinctive bathroom and living pieces, creating an exclusive offering for those with an appreciation for design.’ 2 Contents WASHPLANES Geo Washplane® Solid Surface Single 91 Latis Trestle Table 11 Geo Washplane® Solid Surface Double and Triple 93 CDesign 620 Cabinet 13 Geo Washplane Stone Single 95 CDesign 1330 Cabinet 15 Geo Washplane® Stone Double and Triple 97 Neo 700 Cabinet 17 Geo Washplane® Caesarstone® Single 99 19 Geo Washplane® Caesarstone® Double and Triple 101 Neo Double Cabinet 21 Onda High Washplane® Solid Surface 103 KL Cabinet Dark Oak Veneer 23 Onda Washplane Solid Surface Single 105 KL Cabinet Gunmetal Gloss Thermofoil 25 Onda Washplane® Solid Surface Double and Triple 107 KL Cabinet White Gloss Thermofoil 27 Onda Washplane® Omni Glass Single 109 KL Motion Cabinet Malt Timber Wrap 29 Onda Washplane® Omni Glass Double and Triple 111 KL Motion Cabinet White Gloss Thermofoil 31 Linea Washplane® Solid Surface Single 113 Vessel Cabinet Dark Oak Veneer 33 Linea Washplane Solid Surface Double and Triple 115 Vessel Cabinet Gunmetal Gloss Thermofoil 117 Vessel Cabinet White Gloss Thermofoil 119 Vessel Motion Cabinet Malt Timber Wrap 121 Vessel Motion Cabinet White Gloss Thermofoil 123 Vessel Shelf 9 FURNITURE ® ® ® BASINS Neo 1000 Cabinet 37 Motif 39 Latis Round Solid Surface 41 Latis Round Stone 43 Latis Rectangular Solid Surface 45 Latis Rectangular Stone 127 Latis Bath with Timber Storage End 47 CDesign 620 Solid Surface 129 Latis Bath 49 CDesign 1330 Solid Surface 131 Le Cob Bath 51 Neo Mini Solid Surface 53 Neo 700 Solid Surface 55 Neo 1000 Offset Solid Surface 57 Neo 1000 Centered Solid Surface 59 Neo Double Solid Surface 61 Dune Solid Surface 63 KL Solid Surface 65 KL Stone 67 KL Ceramic 69 Mono Solid Surface with optional Pedestal 71 Mono Stone with optional Pedestal 73 PondTM Solid Surface 75 PondTM Stone 151 PondTM Ceramic Orchid 77 153 Aqua Glass Shallow Eyoi yoi 79 155 Aqua Glass Deep Worvo 81 157 Cubo Stone Acacia 83 159 Cubolong Stone Uleabe 85 161 Softskin Xploff 87 BATH ACCESSORIES 135 Ulisse Wall Outlets 137 Ulisse Hob and Floor Outlets 139 Tom Stool 141 Cero Stool 143 Sub-cero Stool 145 La la stool 147 Tangier LIVING edition three 5 edition three 6 Washplane ® edition three 7 Geo Washplane® Solid Surface Single edition three 9 Geo Washplane® Solid Surface Single Available finishes Solid surface white. Additional information and recommended fittings Use a 200 mm wall outlet for all Washplanes with the exception of Washplane ì800î illustrations. the 800 single Washplane which requires a 150 mm wall outlet. ® Select an outlet that uses 5-7 litres per minute with the water falling at a 90 degree angle directly onto the Washplane®. The Omvivo wall outlets are ideal to use with a Washplane®. A cavity wall is needed to house the hardware and plumbing. Assembly Washplane® assembly includes: - Washplane® Top - Stainless steel cantilever brackets - Zinc plated steel mounting frame - Stainless steel tray - Stainless steel removable drainer - Stainless steel facia - Location saddles Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Linea - solid surface ©OMVIVO Pty Ltd. 1997. 800 mm Cleaning 500 mm 150 mm Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used mm surface in wide circular motions. with a soft cloth over the350 entire Finish by cleaning off detergents with a soft wet cloth and towel dry. 180 mm maximum Assembly 12 mm Geo - solid surface 1200 mm 800 mm 600 mm 500 mm Mounting frame 200 mm 150 mm Facia Tray Cantilever bracket x 2 400 mm 350 mm 180 mm maximum 180 mm maximum 30 mm 30 mm Washplane® Drainer Geo - stone 1200 mm Mounting frame 600 mm 200 mm 800 mm 500 mm 400 mm 150 mm 180 mm maximum 350 mm 30 mm Facia Tray Cantilever bracket x 2 Washplane® 180 mm maximum Drainer 40 mm Onda - solid surface 800 mm 150 mm 500 mm 350 mm 180 mm maximum design Omvivo 19 mm Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 10 Geo Washplane® Solid Surface Double and Triple edition three 11 Geo Washplane® Solid Surface Double and Triple Available finishes Additional information and recommended fittings Solid surface white. Use a 200 mm wall outlet for all Washplanes with the exception of the 800 single Washplane® which requires a 150 mm wall outlet. Select an outlet that uses 5-7 litres per minute with the water falling at a 90 degree angle directly onto the Washplane®. The Omvivo wall outlets are ideal to use with a Washplane®. A cavity wall is needed to house the hardware and plumbing. Assembly Washplane® assembly includes: - Washplane® Top - Stainless steel cantilever brackets - Zinc plated steel mounting frame - Stainless steel tray - Stainless steel removable drainer - Stainless steel facia - Location saddles *Recommended triple dimensions Triple Washplanes are made to order, please contact Omvivo to discuss your requirements. Important Cleaning Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 1997. Assembly 1600 mm 500 mm 200 mm 500 mm Mounting frame Facia x 2 Tray x 2 Cantilever bracket x 3 400 mm 180 mm maximum Double washplane® 30 mm 2100 mm 600 mm Drainer x 2 600 mm 400 mm 30 mm Mounting frame Facia x 3 Tray x 3 2250 mm 500 mm 500 mm Cantilever bracket x 4 500 mm Triple washplane® * 400 mm 30 mm Drainer x 3 design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 12 Geo Washplane® Stone Single edition three 13 Geo Washplane® Stone Single Linea Linea -- solid solid surface surface Available finishes Additional information and recommended fittings Selection of natural stones. 500 500 mm mm 150mm mm 150 For available finishes please refer to the Omvivo website or contact Omvivo directly. Use a 200 mm wall outlet for all Washplanes with the exception of the 800 single Washplane® which requires a 150 mm wall outlet. Select an outlet that uses 5-7 litres per minute with the water falling at a 90 degree angle directly onto the Washplane®. The Omvivo wall outlets are ideal to use with a Washplane®. A cavity wall is needed to house the hardware and plumbing. 800 800mm mm 350 350mm mm Assembly Washplane® assembly includes: - Washplane® Top - Stainless steel cantilever brackets 12 12mm mm - Zinc plated steel mounting frame - Stainless steel tray - Stainless steel removable drainer - Stainless steel facia - Location saddles 180mm mm 180 maximum maximum Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Geo Geo -- solid solid surface surface ©OMVIVO Pty Ltd. 1997. 800 800mm mm 500 500mm mm Cleaning 150 150mm mm Natural stone - Wipe up spills immediately. Clean with warm soapy water (a mild, neutral PH7, non-acidic detergent) and a soft cloth. 350 350mm mm Finish by cleaning off detergents with a soft wet cloth and towel dry. To ensure your natural stone looks its best year180 after year, apply a 180 mm mm maximum stone sealant approximately every 6 months ormaximum when required. 30 30mm mm Assembly Geo Geo -- stone stone -1200 mm 800 800mm mm 600 mm 500 500mm mm Mounting frame 200 mm 150 150mm mm Facia Tray Cantilever bracket x 2 400 350 350mm mm mm 180 mm maximum 180 180mm mm maximum maximum Drainer 40 mm 40 40mm mm Onda Onda -- solid solid surface surface 1200 mm Mounting frame 600 mm 200 mm 800 800mm mm 150 150mm mm 500 500mm mm Washplane® Facia Tray Cantilever bracket x 2 400 mm 180 mm maximum 350mm mm 350 Washplane® 180 180mm mm maximum maximum 40 mm Drainer 19mm mm 19 design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 14 Geo Washplane® Stone Double and Triple edition three 15 Geo Washplane® Stone Double and Triple Available finishes Additional information and recommended fittings Selection of natural stones. For available finishes please refer to the Omvivo website or contact Omvivo directly. Use a 200 mm wall outlet for all Washplanes with the exception of the 800 single Washplane® which requires a 150 mm wall outlet. Select an outlet that uses 5-7 litres per minute with the water falling at a 90 degree angle directly onto the Washplane®. The Omvivo wall outlets are ideal to use with a Washplane®. A cavity wall is needed to house the hardware and plumbing. Assembly Washplane® assembly includes: - Washplane® Top - Stainless steel cantilever brackets - Zinc plated steel mounting frame - Stainless steel tray - Stainless steel removable drainer - Stainless steel facia - Location saddles *Recommended triple dimensions Triple Washplanes are made to order, please contact Omvivo to discuss your requirements. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cleaning Natural stone - Wipe up spills immediately. Clean with warm soapy water (a mild, neutral PH7, non-acidic detergent) and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. To ensure your natural stone looks its best year after year, apply a stone sealant approximately every 6 months or when required. ©OMVIVO Pty Ltd. 1997. Assembly 1600 mm 500 mm 200 mm 500 mm Mounting frame Facia x 2 Tray x 2 Cantilever bracket x 3 400 mm 180 mm maximum Double washplane® 40 mm 2100 mm 600 mm Drainer x 2 600 mm 400 mm 40 mm Mounting frame Facia x 3 Tray x 3 2100 mm 500 mm 500 mm Cantilever bracket x 4 500 mm Triple washplane® 400 mm * 40 mm Drainer x 3 design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 16 Geo Washplane® Caesarstone® Single edition three 17 Geo Washplane® Caesarstone® Single Available finishes Cleaning Snow Caesarstone® Latte Caesarstone® Mink Caesarstone® Caesarstone® - Clean with a mild detergent and soft cloth. For stubborn stains a non scratch or delicate scrub pad can be used with a mild detergent. Finish by cleaning off detergents with a soft wet cloth and towel dry. Caesarstone® does not need sealing or waxing and is virtually maintenance free. In Australia, this product is available exclusively through Reece showrooms. Additional information and recommended fittings Use a 200 mm wall outlet for all Washplanes with the exception of the 800 single Washplane® which requires a 150 mm wall outlet. Select an outlet that uses 5-7 litres per minute with the water falling at a 90 degree angle directly onto the Washplane®. The Omvivo wall outlets are ideal to use with a Washplane®. A cavity wall is needed to house the hardware and plumbing. Assembly Washplane® assembly includes: - Washplane® Top - Stainless steel cantilever brackets - Zinc plated steel mounting frame - Stainless steel tray - Stainless steel removable drainer - Stainless steel facia - Location saddles Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 1997. Assembly 1200 mm Mounting frame 600 mm 200 mm Facia Tray Cantilever bracket x 2 400 mm 180 mm maximum 40 mm Washplane® Drainer design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 18 Geo Washplane® Caesarstone® Double and Triple edition three 19 Geo Washplane® Caesarstone® Double and Triple Available finishes used with a mild detergent. Finish by cleaning off detergents with a soft wet cloth and towel dry. Caesarstone® does not need sealing or waxing and is virtually maintenance free. Snow Caesarstone® Latte Caesarstone® Mink Caesarstone® Additional information and recommended fittings Use a 200 mm wall outlet for all Washplanes with the exception of the 800 single Washplane® which requires a 150 mm wall outlet. Select an outlet that uses 5-7 litres per minute with the water falling at a 90 degree angle directly onto the Washplane®. The Omvivo wall outlets are ideal to use with a Washplane®. A cavity wall is needed to house the hardware and plumbing. In Australia, this product is available exclusively through Reece showrooms. Assembly Washplane® assembly includes: - Washplane® Top - Stainless steel cantilever brackets - Zinc plated steel mounting frame - Stainless steel tray - Stainless steel removable drainer - Stainless steel facia - Location saddles *Recommended triple dimensions Triple Washplanes are made to order, please contact Omvivo to discuss your requirements. Important Cleaning This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Caesarstone® - Clean with a mild detergent and soft cloth. For stubborn stains a non scratch or delicate scrub pad can be ©OMVIVO Pty Ltd. 1997. Assembly 1600 mm 500 mm 200 mm 500 mm Mounting frame Facia x 2 Tray x 2 Cantilever bracket x 3 400 mm 180 mm maximum Double washplane® 40 mm 2100 mm 600 mm Drainer x 2 600 mm 400 mm 40 mm Mounting frame Facia x 3 Tray x 3 2250 mm 500 mm 500 mm Cantilever bracket x 4 500 mm Triple washplane® 400 mm * 40 mm Drainer x 3 design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 20 Onda High Washplane® Solid Surface edition three 21 Onda High Washplane® Solid Surface Available finishes Additional information and recommended fittings Solid surface white. Use a 200 mm wall outlet for all Washplanes with the exception of the 800 single Washplane® which requires a 150 mm wall outlet. Select an outlet that uses 5-7 litres per minute with the water falling at a 90 degree angle directly onto the Washplane®. The Omvivo wall outlets are ideal to use with a Washplane®. A cavity wall is needed to house the hardware and plumbing. Assembly Washplane® assembly includes: - Washplane® Top with towel rail - Zinc plated steel mounting frame - Stainless steel tray - Stainless steel removable drainer - Stainless steel facia Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cleaning Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. ©OMVIVO Pty Ltd. 2002. Assembly 1180 mm 600 mm 200 mm Mounting frame Facia Tray 375 mm 180 mm maximum 65 mm nom 19 mm 850 mm Washplane® Drainer design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 22 Onda Washplane® Solid Surface Single edition three 23 1212mm mm Geo Geo -- solid solid surface surface ® Onda 800 Washplane Solid Surface Single 800mm mm 500 500mm mm Available Finishes 150 150mm mm Additional information and recommended fittings 350 350mm mm Solid surface white. 180 180mm mm maximum maximum Assembly Washplane® assembly includes: 3030mm mm - Washplane® Top - Stainless steel cantilever brackets - Zinc plated steel mounting frame - Stainless steel tray - Stainless steel removable drainer 800 800mm mm - Stainless steel facia 500 500mm mm - Location saddles Use a 200 mm wall outlet for all Washplanes with the exception of the 800 single Washplane® which requires a 150 mm wall outlet. Select an outlet that uses 5-7 litres per minute with the water falling at a 90 degree angle directly onto the Washplane®. The Omvivo wall outlets are ideal to use with a Washplane®. A cavity wall is needed to house the hardware and plumbing. Important Geo Geo -- stone stone -- This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. 150 150mm mm ©OMVIVO Pty Ltd. 2001. Cleaning 350 350mm mm Solid surface - Clean with a mild detergent and a soft cloth. 180 180mm mm For more stubborn marks a very mild abrasivemaximum cleaner maximumcan be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. 4040mm mm Assembly Onda Onda -- solid solid surface surface Mounting frame 1180 mm 800 mm 800 mm 600 mm 500 500mm mm 200 mm 150 150mm mm Facia Tray Cantilever bracket x 2 375 mm 350mm mm 350 180 mm maximum 180 180 mm mm maximum maximum 19 mm mm 1919mm Washplane® Drainer Mounting frame 1180 mm 600 mm 200 mm Facia Tray Cantilever bracket x 2 375 mm 180 mm maximum 19 mm Washplane® Drainer design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 24 Onda Washplane® Solid Surface Double and Triple edition three 25 Onda Washplane® Solid Surface Double and Triple Available finishes Additional information and recommended fittings Solid surface white. Use a 200 mm wall outlet for all Washplanes with the exception of the 800 single Washplane® which requires a 150 mm wall outlet. Select an outlet that uses 5-7 litres per minute with the water falling at a 90 degree angle directly onto the Washplane®. The Omvivo wall outlets are ideal to use with a Washplane®. A cavity wall is needed to house the hardware and plumbing. Assembly Washplane® assembly includes: - Washplane® Top - Stainless steel cantilever brackets - Zinc plated steel mounting frame - Stainless steel tray - Stainless steel removable drainer - Stainless steel facia - Location saddles *Recommended triple dimensions Triple Washplanes are made to order, please contact Omvivo to discuss your requirements. Important Cleaning Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2001. Assembly 1600 mm 500 mm 500 mm 200 mm Mounting frame Facia x 2 Tray x 2 375 mm Cantilever bracket x 3 180 mm maximum Double washplane 19 mm 2100 mm 600 mm Drainer x 2 600 mm 375 mm Mounting frame 19 mm Facia x 3 Tray x 3 500 mm 2250 mm 500 mm Cantilever bracket x 4 500 mm Triple washplane 375 mm * Drainer x 3 19 mm design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 26 Onda Washplane® Omni Glass Single edition three 27 Onda Washplane® Omni Glass Single Available finishes Additional information and recommended fittings Selection of colours. For available colours please refer to the Omvivo website or contact Omvivo directly. Use a 200 mm wall outlet for all Washplanes with the exception of the 800 single Washplane® which requires a 150 mm wall outlet. Select an outlet that uses 5-7 litres per minute with the water falling at a 90 degree angle directly onto the Washplane®. The Omvivo wall outlets are ideal to use with a Washplane®. A cavity wall is needed to house the hardware and plumbing. Assembly Washplane® assembly includes: - Washplane® Top - Stainless steel cantilever brackets - Zinc plated steel mounting frame - Stainless steel tray - Stainless steel removable drainer - Stainless steel facia - Location saddles Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2004. Cleaning Omni glass - Clean with warm soapy water, or non acidic, mild detergent and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly Mounting frame 1200 mm 600 mm 200 mm Facia Tray Cantilever bracket x 2 400 mm 180 mm maximum 12 mm Washplane® Drainer design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 28 Onda Washplane® Omni Glass Double and Triple edition three 29 Onda Washplane® Omni Glass Double and Triple Available finishes Additional information and recommended fittings Selection of colours. For available colours please refer to the Omvivo website or contact Omvivo directly. Use a 200 mm wall outlet for all Washplanes with the exception of the 800 single Washplane® which requires a 150 mm wall outlet. Select an outlet that uses 5-7 litres per minute with the water falling at a 90 degree angle directly onto the Washplane®. The Omvivo wall outlets are ideal to use with a Washplane®. A cavity wall is needed to house the hardware and plumbing. Assembly Washplane® assembly includes: - Washplane® Top - Stainless steel cantilever brackets - Zinc plated steel mounting frame - Stainless steel tray - Stainless steel removable drainer - Stainless steel facia - Location saddles *Recommended triple dimensions Triple Washplanes are made to order, please contact Omvivo to discuss your requirements. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cleaning Omni glass - Clean with warm soapy water, or non acidic, mild detergent and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. ©OMVIVO Pty Ltd. 2004. Assembly 1600 mm 500 mm 500 mm 200 mm Mounting frame Facia x 2 Tray x 2 400 mm Cantilever bracket x 3 180 mm maximum Double washplane 12 mm 2100 mm 600 mm Drainer x 2 600 mm 400 mm Mounting frame 12 mm Facia x 3 Tray x 3 500 mm 2250 mm 500 mm * Cantilever bracket x 4 500 mm Triple washplane 400 mm Drainer x 3 12 mm design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 30 Linea Washplane® Solid Surface Single edition three 31 Linea Washplane® Solid Surface Single Available finishes Cleaning Solid surface white Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. In Australia, this product is available exclusively through Reece showrooms. Additional information and recommended fittings Use a 200 mm wall outlet for all Washplanes with the exception of the 800 single Washplane® which requires a 150 mm wall outlet. Select an outlet that uses 5-7 litres per minute with the water falling at a 90 degree angle directly onto the Washplane®. The Omvivo wall outlets are ideal to use with a Washplane®. A cavity wall is needed to house the hardware and plumbing. Assembly Washplane assembly includes: - Washplane® Top - Stainless steel cantilever brackets - Zinc plated steel mounting frame - Stainless steel tray - Stainless steel removable drainer - Stainless steel facia - Location saddles ® Important This is not an installation guide. Washplane ì800î illustrations. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2002. Assembly Linea - solid surface 1180 mm 800 mm 600 mm 500 mm Mounting frame 200 mm 150 mm Facia Tray Cantilever bracket x 2 375 mm 350 mm 180 mm maximum 180 mm maximum 12 mm 12 mm Washplane® Drainer Geo - solid surface 1180 mm Mounting frame 600 mm 200 mm Facia Tray 800 mm 500 mm 375 mm 150 mm 180 mm maximum 350 mm 12 mm 180 mm maximum Cantilever bracket x 2 Washplane® Drainer 30 mm Geo - stone 800 mm 500 mm 150 mm 350 mm 180 mm maximum design Omvivo 40 mm Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Onda - solid surface Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. 800 mm 500 mm 150 mm T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 32 Linea Washplane® Solid Surface Double and Triple edition three 33 Linea Washplane® Solid Surface Double and Triple Available finishes Additional information and recommended fittings Solid surface white Use a 200 mm wall outlet for all Washplanes with the exception of the 800 single Washplane® which requires a 150 mm wall outlet. Select an outlet that uses 5-7 litres per minute with the water falling at a 90 degree angle directly onto the Washplane®. The Omvivo wall outlets are ideal to use with a Washplane®. A cavity wall is needed to house the hardware and plumbing. In Australia, this product is available exclusively through Reece showrooms. Assembly Washplane® assembly includes: - Washplane® Top - Stainless steel cantilever brackets - Zinc plated steel mounting frame - Stainless steel tray - Stainless steel removable drainer - Stainless steel facia - Location saddles *Recommended triple dimensions Triple Washplanes are made to order, please contact Omvivo to discuss your requirements. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cleaning ©OMVIVO Pty Ltd. 2002. Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly 1600 mm 500 mm 500 mm 200 mm Mounting frame Facia x 2 Tray x 2 Cantilever bracket x 3 375 mm 180 mm maximum Double washplane® 12 mm 2100 mm 600 mm Drainer x 2 600 mm 375 mm 12 mm Mounting frame Facia x 3 Tray x 3 500 mm 2250 mm 500 mm Cantilever bracket x 4 500 mm Triple washplane® 375 mm Drainer x 3 * 12 mm design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 34 Basin edition three 35 Motif edition three 37 Motif Available finishes Solid surface and hand etched glass. Selection of pattern options available, please refer to the Omvivo website or contact Omvivo directly. Assembly Motif basin assembly includes: - Basin - Chrome spacer - Ø32 mm Chrome pop-up waste - Rubber seals - Chrome locknut Additional information and recommended fittings Use an outlet that uses 5-7 litres per minute. Omvivo outlets are ideal to use with the Omvivo basin collection. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2009. Cleaning Solid surface and Glass - Clean with warm soapy water or non acidic, mild detergent and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly Waste Ø510 mm 180 mm maximum Top dry seal 80 mm 110 mm 30 mm 67 mm Motif basin Bottom dry seal Spacer Locknut design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 38 Latis Round Solid Surface edition three 39 Latis Round Solid Surface Available finishes Additional information and recommended fittings Use an outlet that uses 5-7 litres per minute. Omvivo outlets are ideal to use with the Omvivo basin collection. The Latis round basin can be bench mounted onto the Latis trestle table. Solid surface white. Assembly Latis round basin assembly includes: - Basin - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cleaning ©OMVIVO Pty Ltd. 2009. Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly Waste Ø420 mm 180 mm maximum Top dry seal Latis round basin 130 mm Bottom dry seal Locknut design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 40 Latis Round Stone edition three 41 Latis Round Stone Available finishes Selection of natural stones. For available finishes, please refer to the Omvivo website or contact Omvivo directly. Assembly Latis round basin assembly includes: - Basin - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut Additional information and recommended fittings Use an outlet that uses 5-7 litres per minute. Omvivo outlets are ideal to use with the Omvivo basin collection. The Latis round basin can be bench mounted onto the Latis trestle table. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cleaning Natural Stone - Wipe up spills immediately. Clean with warm soapy water (a mild, neutral PH7, non-acidic detergent) and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. To ensure your natural stone looks its best year after year, apply a stone sealant approximately every 6 months or when required. ©OMVIVO Pty Ltd. 2009. Assembly Waste Ø420 mm 180 mm maximum Top dry seal Latis round basin 130 mm Bottom dry seal Locknut design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 42 Latis Rectangular Solid Surface edition three 43 Latis Rectangular Solid Surface Available finishes Additional information and recommended fittings Solid surface white. Use an outlet that uses 5-7 litres per minute. Omvivo outlets are ideal to use with the Omvivo basin collection. The Latis rectangular basin can be bench mounted onto the Latis trestle table. Assembly Latis rectangular basin assembly includes: - Basin - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cleaning Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. ©OMVIVO Pty Ltd. 2009. Assembly 600 mm Waste 180 mm maximum Top dry seal 400 mm Latis rectangular basin 130 mm Bottom dry seal Locknut design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 44 Latis Rectangular Stone edition three 45 Latis Rectangular Stone Available finishes Selection of natural stones. For available finishes, please refer to the Omvivo website or contact Omvivo directly. Additional information and recommended fittings Use an outlet that uses 5-7 litres per minute. Omvivo outlets are ideal to use with the Omvivo basin collection. The Latis rectangular basin can be bench mounted onto the Latis trestle table. Assembly Latis rectangular basin assembly includes: - Basin - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2009. Cleaning Natural Stone - Wipe up spills immediately. Clean with warm soapy water (a mild, neutral PH7, non-acidic detergent) and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. To ensure your natural stone looks its best year after year, apply a stone sealant approximately every 6 months or when required. Assembly 600 mm Waste 180 mm maximum Top dry seal 400 mm Latis rectangular basin 130 mm Bottom dry seal Locknut design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 46 CDesign 620 Solid Surface edition three 47 CDesign 620 Solid Surface Available finishes Additional information and recommended fittings Solid surface white. CDesign basins are available with a left or right hand bowl and can be wall mounted or installed with cabinetry. Basin can be ordered with 0, 1 or 3 tap holes. CDesign cabinetry also available. Assembly CDesign 620 basin assembly includes: - Basin with overflow - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2008. Cleaning Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly 620 mm Waste Top dry seal 430 mm 270 mm 173 mm 185 mm 115 mm CDesign 620 basin Bottom dry seal Locknut Note: Drawing and assembly illustrate a right hand bowl. Left hand bowl also available. design Carr Design Group Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 48 CDesign 1330 Solid Surface edition three 49 CDesign 1330 Solid Surface Available finishes Additional information and recommended fittings Solid surface white. CDesign basins are available with a left or right hand bowl and can be wall mounted or installed with cabinetry. Basin can be ordered with 0, 1 or 3 tap holes. CDesign cabinetry also available. Assembly CDesign 1330 basin assembly includes: - Basin with overflow - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2008. Cleaning Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly 1330 mm Waste Top dry seal 430 mm 430 mm 735 mm 115 mm 173 mm CDesign 1330 basin Bottom dry seal Locknut Note: Drawing and assembly illustrate a right hand bowl. Left hand bowl also available. design Carr Design Group Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 50 Neo Mini Solid Surface edition three 51 Neo Mini Solid Surface Additional information and recommended fittings Available finishes Solid surface white. Neo mini basin can be installed with a left or right hand bowl and can be bench mounted or wall mounted. Basin can be ordered with 0 or 1 tap hole. In Australia, this product is available exclusively through Reece showrooms. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Assembly Neo mini basin assembly includes: - Basin with overflow - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut ©OMVIVO Pty Ltd. 2009. Cleaning Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly 470 mm Waste 470 mm Waste Top dry sealTop dry seal Ø240 mm Ø240 mm 300 mm 150 mm 300 mm 150 mm 115 mm 115 mm Neo mini basin Neo mini basin Bottom dryBottom seal dry seal Locknut Locknut Note: Drawing and assembly illustrate a left hand bowl. Right hand bowl also available. design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 52 Neo 700 Solid Surface edition three 53 Neo 700 Solid Surface Additional information and recommended fittings Available finishes Solid surface white. Neo 700 basin can be installed with a left or right hand bowl and can be bench mounted or wall mounted. Basin can be ordered with 0 or 1 tap hole. Neo cabinetry also available. In Australia, this product is available exclusively through Reece showrooms. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Assembly Neo 700 basin assembly includes: - Basin with overflow - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut ©OMVIVO Pty Ltd. 2009. Cleaning Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly 700 mm Ø400 mm Waste Waste Top dry seal Top dry seal 700 mm 450 mm Ø400 mm 225 mm 450 mm 225 mm Neo 700 basin Neo 700 basin 155 mm 155 mm Bottom dry seal Bottom dry seal Locknut Locknut Note: Drawing and assembly illustrate a left hand bowl. Right hand bowl also available. design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 54 Neo 1000 Offset Solid Surface edition three 55 Neo 1000 Offset Solid Surface Additional information and recommended fittings Available finishes Solid surface white. In Australia, this product is available exclusively through Reece showrooms. Neo 1000 offset basin can be installed with a left or right hand bowl and can be bench mounted or wall mounted. Basin can be ordered with 0 or 1 tap hole. Neo cabinetry also available. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Assembly Neo 1000 offset basin assembly includes: - Basin with overflow - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut ©OMVIVO Pty Ltd. 2009. Cleaning Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly Waste Waste 1000 mm 1000 mm Top dryTop sealdry seal Ø400 mm Ø400 mm 450 mm 450 mm 325 mm 325 mm Neo 1000 Neooffset 1000basin offset basin 155 mm 155 mm BottomBottom dry sealdry seal LocknutLocknut Note: Drawing and assembly illustrate a left hand bowl. Right hand bowl also available. design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 56 Neo 1000 Centered Solid Surface edition three 57 Neo 1000 Centered Solid Surface Additional information and recommended fittings Available finishes Solid surface white. Neo 1000 centered basin can be bench mounted or wall mounted. Basin can be ordered with 0 or 1 tap hole. Neo cabinetry also available. In Australia, this product is available exclusively through Reece showrooms. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Assembly Neo 1000 centered basin assembly includes: - Basin with overflow - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut ©OMVIVO Pty Ltd. 2009. Cleaning Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly 1000 mm Ø400 mm Waste 1000 mm 450 mm Ø400 mm 500 mm Waste Top dry seal Top dry seal 450 mm 500 mm 155 mm 155 mm Neo 1000 centered basin Neo 1000 centered basin Bottom dry seal Bottom dry seal Locknut Locknut design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 58 Neo Double Solid Surface edition three 59 m Neo Double Solid Surface Additional information and recommended fittings Available finishes Solid surface white. Neo double basin can be bench mounted or wall mounted. Basin can be ordered with 0 or 1 tap hole. Neo cabinetry also available. In Australia, this product is available exclusively through Reece showrooms. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Assembly Neo double basin assembly includes: - Basin with overflow - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut ©OMVIVO Pty Ltd. 2009. Cleaning Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly 1400 mm 1400 mm Waste Top dry seal Ø400 mm 325 mm 450 mm Waste Top dry seal 450 mm 325 mm Neo double basin 155 mm Neo double basin 155 mm Bottom dry seal Locknut Bottom dry seal Locknut design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 60 Dune Solid Surface edition three 61 Dune Solid Surface Available finishes Additional information and recommended fittings Use a 150 mm wall outlet that uses 5-7 litres per minute. The water must fall at a 90 degree angle, directly down onto Dune. Omvivo outlets are ideal to use with the Omvivo basin collection. The mounting brackets are fixed to studs within a cavity wall. Dune is available with a left or right hand bowl. Solid surface white. Solid surface night. Assembly Dune basin assembly includes: - Basin - Stainless steel mounting brackets - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2008. Cleaning Solid surface - The surface of Dune is polished. Clean with a mild, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Assembly 150 mm 415 mm 1230 mm Waste Top dry seal 180 mm maximum 12 mm 110 mm Dune basin Mounting brackets x 2 Bottom dry seal Locknut Note: Drawing and assembly illustrate a right hand bowl. Left hand bowl also available. design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 62 KL Solid Surface edition three 63 KL Solid Surface Available Finishes Additional information and recommended fittings Solid surface white. Use a 250 mm wall outlet that uses 5-7 litres per minute. The water must fall at a 90 degree angle, directly down onto the KL vessel. Omvivo outlets are ideal to use with the Omvivo basin collection. Assembly KL basin assembly includes: - Basin - Stainless steel drainage grate - Chrome waste - Chrome locknut Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2002. Cleaning Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly 600 mm 250 mm 115 mm Stainless steel grate Waste 510 mm 180 mm maximum 100 mm KL basin Rubber seal Locknut design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 64 KL Stone edition three 65 KL Stone Available finishes Additional information and recommended fittings Selection of natural stones. For available finishes, please refer to the Omvivo website or contact Omvivo directly. Use a 250 mm wall outlet that uses 5-7 litres per minute. The water must fall at a 90 degree angle, directly down onto the KL vessel. Omvivo outlets are ideal to use with the Omvivo basin collection. Assembly Important KL basin assembly includes: - Basin - Stainless steel drainage grate - Chrome waste - Chrome locknut This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 1999. Cleaning Natural stone - Wipe up spills immediately. Clean with warm soapy water (a mild, neutral PH7, non-acidic detergent) and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. To ensure your natural stone looks its best year after year, apply a stone sealant approximately every 6 months or when required. Assembly 600 mm 250 mm 115 mm Stainless steel grate Waste 510 mm 180 mm maximum 100 mm KL basin Rubber seal Locknut design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 66 KL Ceramic edition three 67 KL Ceramic Available Finishes Cleaning White ceramic Ceramic - Clean with warm soapy water or non acidic, mild detergent and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. In Australia, this product is available exclusively through Reece showrooms. Additional information and recommended fittings Assembly Use a 250 mm wall outlet that uses 5-7 litres per minute. The water must fall at a 90 degree angle, directly down onto the KL vessel. Omvivo outlets are ideal to use with the Omvivo basin collection. KL basin assembly includes: - Basin - Stainless steel drainage grate - Chrome waste - Chrome locknut Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2002. Assembly 600 mm 250 mm 115 mm Stainless steel grate Waste 510 mm 180 mm maximum 100 mm KL basin Rubber seal Locknut design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 68 Mono Solid Surface with optional Pedestal edition three 69 Mono Solid Surface with optional Pedestal Available finishes Veneer - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Solid surface white. Pedestal available finishes Additional information and recommended fittings Solid surface white. Selection of timber veneers. For available finishes, please refer to the Omvivo website or contact Omvivo directly. Use an outlet that uses 5-7 litres per minute. For best results the water should fall at a 90 degree angle, directly down onto the vessel. Omvivo outlets are ideal to use with the Omvivo basin collection. The Mono vessel can be partnered with the Mono pedestal or bench mounted. The mono pedestal is suitable for S or P trap plumbing. It has an opening at the rear for access to the waste and for a P trap. Assembly Mono basin assembly includes: - Basin - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut Pedestal is an optional extra. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cleaning ©OMVIVO Pty Ltd. 2006. Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly Waste 180 mm maximum Top dry seal 1120 mm 76 mm Mono basin 850 mm Bottom dry seal Locknut Mono pedestal (purchased separately) design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 70 Mono Stone with optional Pedestal edition three 71 Mono Stone with optional Pedestal Available finishes Veneer - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Selection of natural stones. For available finishes, please refer to the Omvivo website or contact Omvivo directly. Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. Pedestal available finishes Solid surface white. Selection of timber veneers. For available finishes, please refer to the Omvivo website or contact Omvivo directly. Additional information and recommended fittings Use an outlet that uses 5-7 litres per minute. For best results the water should fall at a 90 degree angle, directly down onto the vessel. Omvivo outlets are ideal to use with the Omvivo basin collection. The Mono vessel can be partnered with the Mono pedestal or bench mounted. The mono pedestal is suitable for S or P trap plumbing. It has an opening at the rear for access to the waste and for a P trap. Assembly Mono basin assembly includes: - Basin - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut Pedestal is an optional extra. Important Cleaning Natural stone - Wipe up spills immediately. Clean with warm soapy water (a mild, neutral PH7, non-acidic detergent) and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. To ensure your natural stone looks its best year after year, apply a stone sealant approximately every 6 months or when required. This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2006. Assembly Waste 180 mm maximum Top dry seal 1120 mm 76 mm Mono basin 850 mm Bottom dry seal Locknut Mono pedestal (purchased separately) design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 72 PondTM Solid Surface edition three 73 PondTM Solid Surface Available Finishes Additional information and recommended fittings Solid surface white. Use an outlet that uses 5-7 litres per minute. For best results the water should fall at a 90 degree angle, directly down onto the vessel. Omvivo outlets are ideal to use with the Omvivo basin collection. Assembly PondTM basin assembly includes: - Basin - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut - Chrome spacer Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2001. Cleaning Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly Waste Ø515 mm 180 mm maximum Top dry seal Pond™ basin 70 mm 95 mm 12 mm 25 mm 67 mm Bottom dry seal Spacer Locknut design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 74 PondTM Stone edition three 75 PondTM Stone Available finishes Additional information and recommended fittings Selection of natural stones. For available finishes, please refer to the Omvivo website or contact Omvivo directly. Use an outlet that uses 5-7 litres per minute. For best results the water should fall at a 90 degree angle, directly down onto the vessel. Omvivo outlets are ideal to use with the Omvivo basin collection. Assembly Important PondTM basin assembly includes: - Basin - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknuts - Chrome spacer This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2001. Cleaning Natural stone - Wipe up spills immediately. Clean with warm soapy water (a mild, neutral PH7, non-acidic detergent) and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. To ensure your natural stone looks its best year after year, apply a stone sealant approximately every 6 months or when required. Assembly Waste Ø520 mm 180 mm maximum Top dry seal Pond™ basin 95 mm 20 mm 120 mm 25 mm 136 mm Bottom dry seal Locknut Collar washer Spacer Rubber washer Locknut design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 76 PondTM Ceramic edition three 77 PondTM Ceramic Available finishes Additional information and recommended fittings White ceramic In Australia, this product is available exclusively through Reece showrooms. Use an outlet that uses 5-7 litres per minute. For best results the water should fall at a 90 degree angle, directly down onto the vessel. Omvivo outlets are ideal to use with the Omvivo basin collection. Assembly Important PondTM basin assembly includes: - Basin - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknuts - Chrome spacer This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2001. Cleaning Ceramic - Clean with warm soapy water or non acidic, mild detergent and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly Waste Ø515 mm 180 mm maximum Pond™ basin 80 mm 15 mm 105 mm 25 mm 136 mm Bottom dry seal Locknut Collar washer Spacer Rubber washer Locknut design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 78 Aqua Glass Shallow edition three 79 Aqua Glass Shallow Available finishes Additional information and recommended fittings Selection of glass options. For available finishes, please refer to the Omvivo website or contact Omvivo directly. Use an outlet that uses 5-7 litres per minute. For best results the water should fall at a 90 degree angle, directly down onto the vessel. Omvivo outlets are ideal to use with the Omvivo basin collection. Assembly Important Aqua basin assembly includes: - Basin - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut - Chrome spacer This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 1993. Cleaning Glass - Clean with warm soapy water, or non acidic, mild detergent and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly Waste Ø495-505 mm 180 mm maximum Top dry seal Aqua basin 70-80 mm 95-105 mm 15 mm 25 mm 67 mm Bottom dry seal Spacer Locknut design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 80 Aqua Glass Deep edition three 81 Aqua Glass Deep Available finishes Additional information and recommended fittings Selection of glass options. For available finishes, please refer to the Omvivo website or contact Omvivo directly. Use an outlet that uses 5-7 litres per minute. For best results the water should fall at a 90 degree angle, directly down onto the vessel. Omvivo outlets are ideal to use with the Omvivo basin collection. Assembly Important Aqua basin assembly includes: - Basin - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut - Chrome spacer This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 1993. Cleaning Glass - Clean with warm soapy water, or non acidic, mild detergent and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly Waste Ø435 mm 180 mm maximum Top dry seal Aqua basin 120 mm 15 mm 145 mm 25 mm 67 mm Bottom dry seal Spacer Locknut design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 82 Cubo Stone edition three 83 Cubo Stone Available finishes Additional information and recommended fittings Selection of natural stones. For available finishes, please refer to the Omvivo website or contact Omvivo directly. Use an outlet that uses 5-7 litres per minute. For best results the water should fall at a 90 degree angle, directly down onto the vessel. Omvivo outlets are ideal to use with the Omvivo basin collection. Assembly Important Cubo basin assembly includes: - Basin - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 1999. Cleaning Natural Stone - Wipe up spills immediately. Clean with warm soapy water (a mild, neutral PH7, non-acidic detergent) and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. To ensure your natural stone looks its best year after year, apply a stone sealant approximately every 6 months or when required. Assembly 500 mm Waste Top dry seal Ø440 mm 500 mm 180 mm maximum Cubo basin 100 mm Bottom dry seal Locknut design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 84 Cubolong Stone edition three 85 Cubolong Stone Available finishes Additional information and recommended fittings Selection of natural stones. For available finishes, please refer to the Omvivo website or contact Omvivo directly. Use an outlet that uses 5-7 litres per minute. For best results the water should fall at a 90 degree angle, directly down onto the vessel. Omvivo outlets are ideal to use with the Omvivo basin collection. Assembly Important Cubolong basin assembly includes: - Basin - Ø32 mm chrome pop up waste - Rubber seals - Chrome locknut This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 1999. Cleaning Natural stone - Wipe up spills immediately. Clean with warm soapy water (a mild, neutral PH7, non-acidic detergent) and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. To ensure your natural stone looks its best year after year, apply a stone sealant approximately every 6 months or when required. Assembly 700 mm Waste ø440 mm 500 mm 180 mm maximum 100 mm Top dry seal Cubolong basin Bottom dry seal Locknut Note: Drawing and assembly illustrate a right hand bowl. Left hand bowl also available. design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 86 Softskin edition three 87 Softskin Available finishes Selection of colours. For available colours please refer to the Omvivo website or contact Omvivo directly. Additional information and recommended fittings Softskin provides a two tone effect that has a durable tactile finish. Softskin is applied to a range of Omvivo’s solid surface basins including KL, Mono and Latis. Assembly Softskin finish is available on solid surface basins. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cleaning Softskin - Clean with warm soapy water or non acidic, non abrasive, mild detergent and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. ©OMVIVO Pty Ltd. 2009. Softskin application examples Latis rectangular basin Latis round basin KL basin Mono basin CDesign 620 basin Mono basin with pedestal CDesign 1330 basin design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 88 Furniture edition three 89 Latis Trestle Table edition three 91 Latis Trestle Table Available finishes Cleaning Selection of timber finishes. For available finishes, please refer to the Omvivo website or contact Omvivo directly. Timber - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. For individual shelf cleaning recommendations please contact Omvivo. Trestle Shelf available finishes Solid surface white. Selection of natural stone. Selection of timber finishes. For available finishes, please refer to the Omvivo website or contact Omvivo directly. Additional information and recommended fittings The Latis trestle table is designed specifically to compliment the Latis basins and will also suit other Omvivo basins such as the Mono, Aqua and Pond. Assembly Important Latis Trestle table assembly includes: - Trestle table - Trestle shelf This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2009. Assembly 1600 mm Trestle table 510 mm Trestle shelf 535 mm 735 mm design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 92 CDesign 620 Cabinet edition three 93 CDesign 620 Cabinet Available finishes Additional information and recommended fittings Powder coat white. The CDesign 620 cabinet is designed to be wall mounted. The CDesign 620 cabinet is designed specifically to compliment the CDesign 620 basin, which can be installed on the cabinet with a left or right hand bowl. Assembly CDesign 620 cabinet assembly includes: - Cabinet body - Large drawer - Soft close drawer mechanism - Full length powder coat handle Cleaning Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2008. Assembly 620 mm CDesign 620 basin (purchased separately) 430 mm Full length handle Large drawer Cabinet body 525 mm 350 mm design Carr Design Group Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 94 CDesign 1330 Cabinet edition three 95 CDesign 1330 Cabinet Available finishes Additional information and recommended fittings Powder coat white. The CDesign 1330 cabinet is designed to be wall mounted. The CDesign 1330 cabinet is designed specifically to compliment the CDesign 1330 basin, which can be installed on the cabinet with a left or right hand bowl. Assembly CDesign 1330 cabinet assembly includes: - Cabinet body - Large drawers - Soft close drawer mechanisms - Full length powder coat handle Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cleaning Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. ©OMVIVO Pty Ltd. 2008. Assembly 1330 mm CDesign 1330 basin (purchased separately) 430 mm Full length handle Large drawer 525 mm 350 mm Cabinet body design Carr Design Group Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 96 Neo 700 Cabinet edition three 97 Neo 700 Cabinet Available finishes Additional information and recommended fittings Selection of finishes. For available finishes, please refer to the Omvivo website or contact Omvivo directly. In Australia, this product is available exclusively through Reece showrooms. The Neo 700 cabinet is designed to be wall mounted. The Neo 700 cabinet is designed specifically to compliment the Neo 700 basin, which can be installed on the cabinet with a left or right hand bowl. There are three designer handles to choose from which can be positioned on the left, right or centre of the Neo drawer. Assembly Important Neo 700 cabinet assembly includes: - Cabinet body - Large drawer - Adjustable shelf - Soft close drawer mechanism - Chrome designer handle This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2009. Cleaning Thermofoil - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Assembly 700 mm Neo 700 basin (purchased separately) Ø400 mm 450 mm Adjustable shelf Designer handle Large drawer 225 mm 155 mm Cabinet body 500 mm design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 98 Neo 1000 Cabinet edition three 99 Neo 1000 Cabinet Available finishes Cleaning Selection of finishes. For available finishes, please refer to the Omvivo website or contact Omvivo directly. Thermofoil - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. In Australia, this product is available exclusively through Reece showrooms. Additional information and recommended fittings Assembly Neo 1000 cabinet assembly includes: - Cabinet body - Large drawer - Adjustable shelf - Soft close drawer mechanism - Chrome designer handle The Neo 1000 cabinet is designed to be wall mounted. The Neo 1000 cabinet is designed specifically to compliment the Neo 1000 centered basin and the Neo 1000 offset basin. The Neo 1000 offset basin can be installed with a left or right hand bowl. There are three designer handles to choose from which can be positioned on the left, right or centre of the neo drawer. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2009. Assembly 1000 mm 1000 mm Neo 1000 basin Neo 1000 basin (purchased separately) (purchased separately) Ø400 mm Ø400 mm 450 mm 450 mm Adjustable shelf Designer handle Large drawer 155 mm 500 mm Adjustable shelf Designer handle Large drawer 155 mm 500 mm Cabinet body Cabinet body design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 100 Neo Double Cabinet edition three 101 Neo Double Cabinet Available finishes Cleaning Selection of finishes. For available finishes, please refer to the Omvivo website or contact Omvivo directly. Thermofoil - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. In Australia, this product is available exclusively through Reece showrooms. Additional information and recommended fittings The Neo double cabinet is designed to be wall mounted. The Neo double cabinet is designed specifically to compliment the Neo double basin. There are three designer handles to choose from which can be positioned on the left, right or centre of the Neo drawer. Assembly Neo double cabinet assembly includes: - Cabinet body - Large drawers - Adjustable shelves - Soft close drawer mechanism - Chrome designer handle Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2009. Assembly 1400 mm 1400 mm Neo double basin Neo double basin (purchased separately) (purchased separately) Ø400 mm Ø400 mm 450 mm 450 mm Adjustable shelf Adjustable shelf Large drawer Large drawer 325 mm 325 mm 155 mm 155 mm 500 mm 500 mm Designer handle Designer handle Cabinet body Cabinet body design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 102 KL Cabinet Dark Oak Veneer edition three 103 KL Cabinet Dark Oak Veneer KL basin and Vessel shelf (purchased separately) Internal drawer Available Designer handle KL basin and Vessel shelf (purchased separately) Internal drawer Additional finishes Dark oak veneer. information and recommended fittings The KL cabinet is designed to be wall mounted. Large drawer The KL cabinets are designed specifically to compliment the KL basins and the vessel shelves. Large drawer Assembly KL cabinet assembly includes: - Cabinet body - Large drawer - Internal top drawer - Soft close drawer mechanisms Cabinet body- Steel wall mounting bracket Cleaning Veneer - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Kl cabinet motion Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cabinet body ©OMVIVO Pty Ltd. 1999. Mounting bracket Kl cabinet Assembly KL basin and Vessel shelf (purchased separately) 510 mm KL basin and Vessel shelf (purchased separately) 510 mm Internal drawer Internal drawer Designer handle Large drawer Large drawer Cabinet body Cabinet body Mounting bracket 500 mm 500 mm 600 mm 510 mm 600 mm 510 mm design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 104 KL Cabinet Gunmetal Gloss Thermofoil edition three 105 KL Cabinet Gunmetal Gloss Thermofoil KL basin and Vessel shelf (purchased separately) Internal drawer Available Designer handle KL basin and Vessel shelf (purchased separately) Internal drawer Additional finishes Gunmetal gloss thermofoil. information and recommended fittings The KL cabinet is designed to be wall mounted. Large drawer The KL cabinets are designed specifically to compliment the KL basins and the vessel shelves. Large drawer Assembly KL cabinet assembly includes: - Cabinet body - Large drawer - Internal top drawer - Soft close drawer mechanisms Cabinet body- Steel wall mounting bracket Cleaning Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cabinet body ©OMVIVO Pty Ltd. 1999. Mounting bracket Thermofoil - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Kl cabinet motion Kl cabinet Assembly KL basin and Vessel shelf (purchased separately) 510 mm KL basin and Vessel shelf (purchased separately) 510 mm Internal drawer Internal drawer Designer handle Large drawer Large drawer Cabinet body Cabinet body Mounting bracket 500 mm 500 mm 600 mm 510 mm 600 mm 510 mm design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 106 KL Cabinet White Gloss Thermofoil edition three 107 KL Cabinet White Gloss Thermofoil KL basin and Vessel shelf (purchased separately) KL basin and Vessel shelf (purchased separately) Internal drawer Internal drawer Available finishes Designer handle Large drawerWhite Additional information and recommended fittings gloss thermofoil. KL Large The drawer cabinet is designed to be wall mounted. The KL cabinets are designed specifically to compliment the KL basins and the vessel shelves. Assembly KL cabinet assembly includes: - Cabinet body - Large drawer - Internal top drawer - Soft close drawer mechanisms Cabinet body- Steel wall mounting bracket Cleaning Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cabinet body ©OMVIVO Pty Ltd. 1999. Mounting bracket Thermofoil - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Kl cabinet motion Kl cabinet Assembly KL basin and Vessel shelf (purchased separately) 510 mm KL basin and Vessel shelf (purchased separately) 510 mm Internal drawer Internal drawer Designer handle Large drawer Large drawer Cabinet body Cabinet body Mounting bracket 500 mm 500 mm 600 mm 510 mm 600 mm 510 mm design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 108 KL Motion Cabinet Malt Timber Wrap edition three 109 KL Motion Cabinet Malt Timber Wrap KL basin and Vessel shelf (purchased separately) Internal drawer Available Designer handle KL basin and Vessel shelf (purchased separately) Internal drawer Cleaning finishes Malt timber wrap Large drawer Timber wrap - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Large drawer In Australia, this product is available exclusively through Reece showrooms. Assembly KL Motion cabinet assembly includes: - Cabinet body - Large drawer Cabinet body - Internal top drawer - Soft close drawer mechanisms - Designer handle Additional information and recommended fittings The KL Motion cabinet is designed to be wall mounted. The KL cabinets are designed specifically to compliment the KL basins and the vessel shelves. Cabinet body Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Mounting bracket Kl cabinet motion ©OMVIVO Pty Ltd. 1999. Assembly 510 mm K KL basin and Vessel shelf (purchased separately) 510 mm KL basin a (purchase Internal drawer Internal d Designer handle Large drawer Large dra Cabinet body Cabinet b Mounting 500 mm 500 mm 600 mm 600 mm 510 mm 510 design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 110 KL Motion Cabinet White Gloss Thermofoil edition three 111 KL Motion Cabinet White Gloss Thermofoil KL basin and Vessel shelf KL basin and Vessel shelf (purchased separately) Internal drawer Available Designer handle (purchased separately) Internal drawer Cleaning finishes White gloss thermofoil Large drawer Thermofoil - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Large drawer In Australia, this product is available exclusively through Reece showrooms. Assembly KL Motion cabinet assembly includes: - Cabinet body - Large drawer Cabinet body - Internal top drawer - Soft close drawer mechanisms - Designer handle Additional information and recommended fittings The KL Motion cabinet is designed to be wall mounted. The KL cabinets are designed specifically to compliment the KL basins and the vessel shelves. Cabinet body Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Mounting bracket Kl cabinet motion ©OMVIVO Pty Ltd. 1999. Assembly 510 mm K KL basin and Vessel shelf (purchased separately) 510 mm KL basin a (purchase Internal drawer Internal d Designer handle Large drawer Large dra Cabinet body Cabinet b Mounting 500 mm 500 mm 600 mm 600 mm 510 mm 510 design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 112 Vessel Cabinet Dark Oak Veneer edition three 113 Vessel cabinet separately) er dy Vessel Cabinet Dark Oak Veneer Available finishes Additional information and recommended fittings Dark oak veneer. The vessel cabinet is designed to be wall mounted. The vessel cabinet is designed specifically to compliment the Omvivo Pond and Aqua, Motif basins and the vessel shelves. Assembly Vessel cabinet assembly includes: - Cabinet body - Large drawer - Soft close drawer mechanisms - Steel wall mounting bracket Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 1999. Cleaning Veneer - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Vessel cabinet motion racket Vessel cabinet Assembly Basin (purchased separately) Basin (purchased separately) 400 mm Designer handle Large drawer Large drawer Cabinet body Cabinet body Mounting bracket 500 mm 600 mm 400 mm 400 mm design Omvivo 500 mm Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 500 mm T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 114 Vessel Cabinet Gunmetal Gloss Thermofoil edition three 115 Vessel cabinet separately) er dy Vessel Cabinet Gunmetal Gloss Thermofoil Available finishes Additional information and recommended fittings Gunmetal gloss thermofoil. The vessel cabinet is designed to be wall mounted. The vessel cabinet is designed specifically to compliment the Omvivo Pond and Aqua, Motif basins and the vessel shelves. Assembly Vessel cabinet assembly includes: - Cabinet body - Large drawer - Soft close drawer mechanisms - Steel wall mounting bracket Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 1999. Cleaning Thermofoil - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Vessel cabinet motion racket Vessel cabinet Assembly Basin (purchased separately) Basin (purchased separately) 400 mm Designer handle Large drawer Large drawer Cabinet body Cabinet body Mounting bracket 500 mm 600 mm 400 mm 400 mm design Omvivo 500 mm Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 500 mm T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 116 Vessel Cabinet White Gloss Thermofoil edition three 117 Vessel cabinet separately) er dy Vessel Cabinet White Gloss Thermofoil Available finishes Additional information and recommended fittings White gloss thermofoil. The vessel cabinet is designed to be wall mounted. The vessel cabinet is designed specifically to compliment the Omvivo Pond and Aqua and Motif basins and the vessel shelves. Assembly Vessel cabinet assembly includes: - Cabinet body - Large drawer - Soft close drawer mechanisms - Steel wall mounting bracket Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 1999. Cleaning Thermofoil - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Vessel cabinet motion racket Vessel cabinet Assembly Basin (purchased separately) Basin (purchased separately) 400 mm Designer handle Large drawer Large drawer Cabinet body Cabinet body Mounting bracket 500 mm 600 mm 400 mm 400 mm design Omvivo 500 mm Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 500 mm T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 118 Vessel Motion Cabinet Malt Timber Wrap edition three 119 arately) Vessel cabinet Vessel cabinet motion Vessel Motion Cabinet Malt Timber Wrap Available finishes Malt timber wrap Additional information and recommended fittings Basin (purchased separately) In Australia, this product is available exclusively through Reece showrooms. e The vessel cabinet is designed to be wall mounted. The vessel cabinet is designed specifically to compliment the Omvivo Pond and Aqua, Motif basins and the vessel shelves. Important Assembly Large drawer Vessel Motion cabinet assembly includes: - Cabinet body - Large drawer - Soft close drawer mechanisms - Designer handle Cleaning This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 1999. Cabinet body Timber wrap - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Mounting bracket Vessel cabinet motion Assembly Basin (purchased separately) 400 mm 400 mm Basin (purc Designer handle Large drawer Larg Cabinet body Cabi Mou 500 mm 500 mm 600 mm 600 mm 400 mm design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com 500 mm edition three 120 Vessel Motion Cabinet White Gloss Thermofoil edition three 121 arately) Vessel cabinet Vessel cabinet motion Vessel Motion Cabinet White Gloss Thermofoil Available finishes White gloss thermofoil Additional information and recommended fittings Basin (purchased separately) In Australia, this product is available exclusively through Reece showrooms. e The vessel cabinet is designed to be wall mounted. The vessel cabinet is designed specifically to compliment the Omvivo Pond and Aqua, Motif basins and the vessel shelves. Important Assembly Large drawer Vessel Motion cabinet assembly includes: - Cabinet body - Large drawer - Soft close drawer mechanisms - Designer handle Cleaning This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 1999. Cabinet body Thermofoil - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Mounting bracket Vessel cabinet motion Assembly Basin 400 mm (purchased separately) 400 mm Basin (purc Designer handle Large drawer Larg Cabinet body Cabi Mou 500 mm 500 mm 600 mm 600 mm 400 mm design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] 500 mm www.omvivo.com edition three 122 Vessel Shelf edition three 123 Vessel Shelf Available finishes Additional information and recommended fittings Selection of stone, glass, solid surface and Caesarstone® Please note - The Vessel shelf is used with the Vessel and KL cabinets. It simply sits between the vessel and the cabinet, no fixing is required. In Australia selected finishes are available exclusively through Reece showrooms. For available finishes, please refer to the Omvivo website or contact Omvivo directly. Assembly Each shelf is created from solid materials supplied with a 50 mm waste hole. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 1999. Cleaning For individual shelf cleaning recommendations please contact Omvivo. Assembly KL basin (purchased separately) 1180 mm 590 mm 115 mm Shelf 400 mm Ø50 mm hole 12-40 mm KL cabinet (purchased separately) Basin (purchased separately) Shelf Vessel cabinet (purchased separately) design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 124 Bath edition three 125 Latis Bath with Timber Storage End edition three 127 Latis Bath with Timber Storage End Available finishes Solid surface white with a selection of timber finishes. For available timber, please refer to the Omvivo website or contact Omvivo directly. Timber - Clean with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Additional information and recommended fittings Assembly Latis bath with storage end assembly includes: - Solid surface bath - Timber storage end - Chrome pop up waste - Rubber seals - Locknut Ulisse 950 mm floor outlet. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2009. Cleaning Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly 1800 mm Waste Top dry seal 690 mm 750 mm 150 mm 1600 mm Latis bath 495 mm 600 mm Bottom dry seal Locknut Timber storage end 1320 mm design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 128 Latis Bath edition three 129 Latis Bath Available finishes Solid surface white. Additional information and recommended fittings Assembly Latis bath assembly includes: - Solid surface bath - Chrome pop up waste - Rubber seals - Locknut Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Ulisse 950 mm floor outlet. ©OMVIVO Pty Ltd. 2009. Cleaning Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly 1600 mm Waste Top dry seal 690 mm 750 mm 150 mm 495 mm 600 mm Latis bath Bottom dry seal Locknut 1320 mm design Thomas Coward Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 130 Le Cob Bath edition three 131 Le Cob Bath Available finishes Glass - Clean with warm soapy water or non acidic, mild detergent and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. Solid surface white, glass and charcoal pebbles. Assembly Additional information and recommended fittings Le Cob assembly includes: - 19 mm glass sides - Formed solid surface chaise lounge - Solid surface drainage grate - Smart valve waste - Stainless steel overflow tray - Stainless steel mesh grate - Pebbles Ulisse 950 mm floor outlet. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. © OMVIVO Pty Ltd. 2001. Cleaning Solid surface - Clean with a mild detergent and a soft cloth. For more stubborn marks a very mild abrasive cleaner can be used with a soft cloth over the entire surface in wide circular motions. Finish by cleaning off detergents with a soft wet cloth and towel dry. Assembly 650 mm 650 mm 690 mm LeCob bath 2200 mm Pebbles 660 mm 535 mm Floor Grate Overflow tray 975 mm design Omvivo Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 132 Accessories edition three 133 Ulisse Wall Outlets edition three 135 Ulisse Wall Outlets Available finishes Additional information and recommended fittings Polished chrome. Ulisse wall outlets are perfect for most vessels and baths, and are specifically designed to partner the Omvivo washplane® and basin collection. Each Ulisse outlet is rated 5* and uses approximately 5 litres per minute. To use with a bath simply remove the aerator and replace with a standard bath aerator. The wall outlet suits a standard ½” BSP threaded male fitting. Assembly Ulisse wall outlets’ assembly includes: - Outlet - Flange - Water saving aerator Important Cleaning Polished Chrome - Clean with warm soapy water, or non acidic, mild detergent and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. 10 mm 32 mm 90 mm 50 mm 50 mm 150 mm 150 mm 10 mm 10 mm 25 mm 80 mm 32 mm 90 mm 50 mm 50 mm 200 mm 200 mm 10 mm 10 mm 25 mm 80 mm 32 mm 90 mm 50 mm 50 mm 250 mm ©OMVIVO Pty Ltd. 1997. 10 mm 25 mm 80 mm This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. 250 mm Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 136 Ulisse Hob and Floor Outlets edition three 137 Ulisse Hob and Floor Outlets Available finishes Additional information and recommended fittings Polished chrome. Ulisse hob and floor outlets are perfect for most baths and many vessels, and are specifically designed to partner most of the Omvivo vessel and bath collection. The Ulisse hob and floor outlets can be fixed into position or installed to swivel. Each Ulisse outlet is rated 5* and uses 5 litres per minute. To use with a bath simply remove the aerator and replace with a standard bath aerator. The outlets suit a standard ½ inch BSP threaded male or female fitting. Assembly Ulisse Hob and Floor Outlets’ assembly includes: - Outlet - Flange - Water saving aerator Important Cleaning Polished Chrome - Clean with warm soapy water, or non acidic, mild detergent and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 1997. 232 mm 225 mm 350 mm 220 mm 25 mm 390 mm 270 mm 25 mm 50 mm 25 mm 32 mm 50 mm 232 mm 232 mm 950 mm 1120 mm 980 mm 810 mm 25 mm 32 mm 75 mm 25 mm 32 mm 75 mm Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 138 Tom Stool edition three 139 Tom Stool Available finishes Selection of colours. For available finishes please refer to the Omvivo website or contact Omvivo directly. Assembly Portable stool. Cleaning Additional information and recommended fittings Created from UV stabilised roto-moulded polyethylene, the Tom stool is suitable for indoor and outdoor use and is 100% recyclable. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Clean with warm soapy water, or non acidic, mild detergent and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. ø395 mm 460 mm 300 mm design Korban/Flaubert Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 140 Cero Stool edition three 141 Cero Stool Available finishes Selection of colours. For available finishes please refer to the Omvivo website or contact Omvivo directly. Additional information and recommended fittings Created from UV stabilised roto-moulded polyethylene, the Cero stool is suitable for indoor and outdoor use and is 100% recyclable. Important Assembly This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Portable stool. Cleaning Clean with warm soapy water, or non acidic, mild detergent and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. 575 mm 450 mm 420 mm design Brian Steendÿk Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 142 Sub-cero Stool edition three 143 Sub-cero Stool Available finishes Selection of colours. For available finishes please refer to the Omvivo website or contact Omvivo directly. Additional information and recommended fittings Created from UV stabilised roto-moulded polyethylene, the Sub-cero stool is suitable for indoor and outdoor use and is 100% recyclable.The Sub-cero, a scaled down version of the classic Cero stool, is ideal for children. Assembly Portable stool. Important Cleaning This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Clean with warm soapy water, or non acidic, mild detergent and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. 385 mm 300 mm 280 mm design Brian Steendÿk Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 144 La la stool edition three 145 La la stool Available finishes Selection of colours. For available finishes please refer to the Omvivo website or contact Omvivo directly. Additional information and recommended fittings Assembly Portable stool. Important Created from UV stabilised roto-moulded polyethylene, the La la stool is suitable for indoor and outdoor use and is 100% recyclable. This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cleaning Clean with warm soapy water, or non acidic, mild detergent and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. ø395 mm 420 mm design Helen Kontouris Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 146 Tangier edition three 147 Tangier Available finishes Selection of colours. For available finishes please refer to the Omvivo website or contact Omvivo directly. Additional information and recommended fittings Assembly Portable stool. Important Created from UV stabilised roto-moulded polyethylene, the Tangier stool is suitable for indoor and outdoor use and is 100% recyclable. This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cleaning Clean with warm soapy water, or non acidic, mild detergent and a soft cloth. Finish by cleaning off detergents with a soft wet cloth and towel dry. 1180 mm 450 mm 500 mm design Ivan Woods Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 148 Living edition three 149 edition three 150 Orchid edition three 151 Orchid Available finishes Each Orchid lamp is hand made. The colours for the lamp can be selected using available images and brochures or a Dulux colour chart. The standard colour mix is 20% colour and 80% white, however additional colour can be requested at time of order (POA). Additional information and recommended fittings The Orchid light collection is a range of beautiful, elegant fittings that will add individual style to any room. The range includes a pendant light, table lamp and standard floor lamp. The Orchid will suit either a G9 75W Halogen globe or ES Eddison 15-20W warm white, depending on which is specified at time of ordering. A licensed electrician should install all hardwired fittings. Assembly The Orchid is supplied with either a G9 75W Halogen globe or ES Eddison 15W warm white. Please specify at time of ordering. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cleaning Clean with a light dust or with a soft damp cloth. For a thorough clean, shade is detachable and can be washed in a hot soapy bath and drip dry. ©OMVIVO Pty Ltd. 2008. 1100 mm 900 mm 1100 mm 1100 mm 800 mm 1900 mm 1100 mm 1100 mm (length is measured from the ceiling to centre of light globe) Pendant light Table lamp Floor lamp design Marc Pascal Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 152 Eyoi yoi edition three 153 Eyoi yoi Available finishes Additional information and recommended fittings Each Eyoi yoi lamp is hand made. The colours for the lamp can be selected using available images and brochures or a Dulux colour chart. The standard colour mix is 20% colour and 80% white, however additional colour can be requested at time of order (POA). The Eyoi yoi light collection incorporates modern, sophisticated fittings that add creative elegance to any room. The range includes a pendant light, table lamp and standard floor lamp. The Eyoi yoi will suit either a G9 75W Halogen globe or ES Eddison 20W warm white, depending on which is specified at time of ordering. A licensed electrician should install all hardwired fittings. Assembly The Eyoi yoi is supplied with either a G9 75W Halogen globe or ES Eddison 20W warm white. Please specify at time of ordering. Cleaning Clean with a light dust or with a soft damp cloth. For a thorough clean, shade is detachable and can be washed in a hot soapy bath and drip dry. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2001. 900 mm 850 mm 1800 mm 1500 mm 800 mm 450 mm 900 mm (length is measured from the ceiling to centre of light globe) Pendant light Table lamp Floor lamp design Marc Pascal Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 154 Worvo edition three 155 Worvo Available finishes Additional information and recommended fittings Each Worvo lamp is hand made. The colours for the lamp can be selected using available images and brochures or a Dulux colour chart. The Worvo light collection incorporates modern, sophisticated fittings that add creative elegance to any room. The range includes a pendant light, table lamp and standard floor lamp. The Worvo suits a compact fluorescent bayonet 15-20W warm white globe. A licensed electrician should install all hardwired fittings. Cleaning Clean with a light dust or with a soft damp cloth. For a thorough clean, shade is detachable and can be washed in a hot soapy bath and drip dry. Important This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2001. 300 mm 1500 mm 1520 mm 300 mm 495 mm 480 mm 300 mm (length is measured from the ceiling to centre of light globe) Pendant light Table lamp Floor lamp design Marc Pascal Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 156 Acacia edition three 157 Acacia Additional information and recommended fittings The Acacia light collection incorporates modern, sophisticated fittings that add creative elegance to any room. The range includes a pendant light, table lamp and standard floor lamp. The Acacia suits a compact fluorescent ES Eddison 20W warm white globe. A licensed electrician should install all hardwired fittings. Available finishes White. Assembly The Acacia is supplied with a compact fluorescent ES Eddison 20W warm white. Important Cleaning Clean with a light dust or with a soft damp cloth. For a thorough clean, shade is detachable and can be washed in a hot soapy bath and drip dry. This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2001. 850 mm 850 mm 1500 mm 1800 mm 900 mm 850 mm 850 mm (length is measured from the ceiling to centre of light globe) Pendant light Table lamp Floor lamp design Marc Pascal Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 158 Uleabe edition three 159 Uleabe Available finishes Additional information and recommended fittings Each Uleabe lamp is hand made. The colours for the lamp can be selected using available images and brochures or a Dulux colour chart. The Uleabe light collection incorporates modern, sophisticated fittings that add creative elegance to any room. The range includes a pendant light, table lamp and standard floor lamp. The Uleabe suits a compact fluorescent bayonet 15-20W warm white globe. A licensed electrician should install all hardwired fittings. Important Cleaning Clean with a light dust or with a soft damp cloth. For a thorough clean, shade is detachable and can be washed in a hot soapy bath and drip dry. This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. ©OMVIVO Pty Ltd. 2001. 480 mm 480 mm 1500 mm 1620 mm 800 mm 410 mm 360 mm 360 mm Table lamp Floor lamp 480 mm (length is measured from the ceiling to centre of light globe) Pendant light design Marc Pascal Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 160 Xploff edition three 161 Xploff Available finishes Additional information and recommended fittings Each Xploff lamp is hand made. The colours for the lamp can be selected using available images and brochures or a Dulux colour chart. The standard colour mix is 20% colour and 80% white, however additional colour can be requested at time of order (POA). The Xploff light collection incorporates modern, sophisticated fittings that add creative elegance to any room. The range includes a pendant light, table lamp and standard floor lamp. The Xploff suits a compact fluorescent ES Eddison 20W warm white globe. A licensed electrician should install all hardwired fittings. Assembly Important The Xploff is supplied with a compact fluorescent ES Eddison 20W warm white. This is not an installation guide. Please contact OMVIVO for technical details. Product specifications are subject to alteration without notice. Cleaning Clean with a light dust or with a soft damp cloth. For a thorough clean, shade is detachable and can be washed in a hot soapy bath and drip dry. ©OMVIVO Pty Ltd. 2001. 850 mm 650 mm 1500 mm 1800 mm 900 mm 850 mm 850 mm (length is measured from the ceiling to centre of light globe) Pendant light Table lamp Floor lamp design Marc Pascal Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 Note: due to varying manufacturing methods, the dimensions illustrated here are nominal and subject to change. Omvivo has detailed, to the best of its ability, the most approximate measurement possible for each product given the method of manufacturing used. T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com edition three 162 Omvivo Pty Ltd Schiavello Complex 1 Sharps Road Tullamarine Victoria Australia 3043 T: + 61 3 9339 8130 F: + 61 3 9330 8611 [email protected] www.omvivo.com
