IDENTIVISION IIP- IP NVR recorders Installation Guide

Transcription

IDENTIVISION IIP- IP NVR recorders
Installation Guide
Document version: v1.6. ENG
IP NVR – only with IP channels (NVR)
IIP-N810, 8 csat.
MEGASTORE
IIP-N820, 8 csat.
MEGASTORE
IIP-N810SPOE, 8 csat.
MEGASTORE
IIP-N3210ECO, 8/16/24/32 csat.
MEGASTORE
IIP-N1641, 8/16/24/32 csat.
MEGASTORE
IIP-N2480, 24/32 csat.
MEGASTORE
IIP-N820SPOE, 8 csat
MEGASTORE
IDENTIVISION IP NVR INSTALLATION GUIDE
CONTENT
1.
Product ...................................................................................................................................................... 5
1.1
2.
Product overview................................................................................................................................ 5
Open-package check and cable connections........................................................................................... 5
2.1
Open-package check ......................................................................................................................... 5
2.2
HDD installatation .............................................................................................................................. 6
2.3
IIP-N410-N411S-N411SPOE-N4120-N3210-.................................................................................... 7
2.4
IIP-N820 ............................................................................................................................................. 8
2.5
IIP-N1640-N1641 ............................................................................................................................... 9
2.6
IIP-N2460-N2480 ............................................................................................................................. 10
2.7
Audio and video input and output connections................................................................................ 11
2.7.1
Video input connections ........................................................................................................... 11
2.7.2
Video output connections and options ..................................................................................... 11
2.7.3
Audio signal input ..................................................................................................................... 11
2.7.4
Audio signal output ................................................................................................................... 11
2.7.5
Alarm input and output connections......................................................................................... 12
2.7.6
Alarm input port specification ................................................................................................... 12
2.7.7
Alarm output port specification ................................................................................................. 13
2.7.8
Alarm output port relay parameters.......................................................................................... 13
2.7.9
Speed dome connections......................................................................................................... 13
2.8
Turn on ............................................................................................................................................. 14
2.9
Turn off ............................................................................................................................................. 14
2.9.1
Auto resume after power failure ............................................................................................... 14
2.9.2
Replace the hard disk............................................................................................................... 14
2.9.3
Replace the battery .................................................................................................................. 14
2.10
Login................................................................................................................................................. 15
2.11
Plug&Play (Wizard) .......................................................................................................................... 16
2.12
Plug&Play (Wizard) 2. ...................................................................................................................... 16
3.
Remote controller.................................................................................................................................... 17
4.
mouse operation ..................................................................................................................................... 18
5.
Preview.................................................................................................................................................... 19
5.1.1
6.
Control buttons ......................................................................................................................... 19
Desktop shortcut menu ........................................................................................................................... 20
6.1
Menu ................................................................................................................................................ 20
6.2
Playback........................................................................................................................................... 21
6.2.1
Playback control ....................................................................................................................... 22
6.3
Backup ............................................................................................................................................. 22
6.4
Record backup ................................................................................................................................. 23
6.5
Recorded files playing on a PC ....................................................................................................... 24
6.6
Files Convert .................................................................................................................................... 24
6.7
Record mode.................................................................................................................................... 25
6.8
Color settings ................................................................................................................................... 25
6.9
Output Adjust ................................................................................................................................... 25
Product specifications, parameters, functions of the device can change without notice!
2
6.10
PTZ control....................................................................................................................................... 26
6.11
PTZ Special functions：............................................................................................................... 27
6.11.1
Preset ....................................................................................................................................... 27
6.11.2
Cruise between Points ............................................................................................................. 27
6.11.3
Scan.......................................................................................................................................... 28
6.11.4
Boundary Scan ......................................................................................................................... 29
6.11.5
Horizontal Rotating ................................................................................................................... 29
6.11.6
Rotate ....................................................................................................................................... 30
6.11.7
Reset ........................................................................................................................................ 30
6.12
7.
Logout .............................................................................................................................................. 30
Record mode........................................................................................................................................... 31
7.1
8.
Snapshot storage (Partial model support) ....................................................................................... 31
Alarm ....................................................................................................................................................... 33
8.1
Video motion .................................................................................................................................... 33
8.2
Video blind........................................................................................................................................ 34
8.3
Video loss......................................................................................................................................... 35
8.4
Abnormal .......................................................................................................................................... 35
9.
System setup .......................................................................................................................................... 36
9.1
General............................................................................................................................................. 36
9.2
Network settings............................................................................................................................... 37
9.3
Netservice ........................................................................................................................................ 38
9.4
GUI display....................................................................................................................................... 44
9.5
Tour setup ........................................................................................................................................ 45
10.
Advanced ............................................................................................................................................. 45
10.1
HDD manage ................................................................................................................................... 45
10.2
Account ............................................................................................................................................ 46
10.3
Online user ....................................................................................................................................... 48
10.4
TV settings ....................................................................................................................................... 49
10.5
Auto-maintain ................................................................................................................................... 49
10.6
Restore............................................................................................................................................. 49
10.7
Upgrade............................................................................................................................................ 50
10.8
Eszköz infó ..................................................................................... Hiba! A könyvjelző nem létezik.
10.9
Import/export .................................................................................................................................... 51
11.
Info menü ............................................................................................................................................. 51
11.1
HDD információ................................................................................................................................ 51
11.2
BPS .................................................................................................................................................. 52
11.3
Log ................................................................................................................................................... 53
11.4
Version ............................................................................................................................................. 53
12.
Digital channels.................................................................................................................................... 55
12.1
Basic knowledge .............................................................................................................................. 55
12.2
Digital channels.............................................................................. Hiba! A könyvjelző nem létezik.
12.3
First steps......................................................................................................................................... 56
12.4
Static IP address to the Cameras .................................................................................................... 56
3
12.4.1
Add device to CMS software .................................................................................................... 56
12.4.2
Static IP address with Upgrade Tool........................................................................................ 59
12.4.3
Static IP address with CMS...................................................................................................... 61
12.4.4
Port forwarding ......................................................................................................................... 62
12.5
Recorder settings ............................................................................................................................. 66
12.6
Digital channels................................................................................................................................ 66
12.6.1
Add camera to the recorder...................................................................................................... 66
13.
Lan connection..................................................................................................................................... 67
14.
Cloud connection\Remote access ....................................................................................................... 68
14.1
Cloud connection\Remote Access................................................................................................... 68
14.2
Remote access (without wizard) ...................................................................................................... 69
14.3
Remote access (with more devices)................................................................................................ 69
15.
Mobilphone\Tablet access with vmeye app......................................................................................... 70
16.
CLoud access with vMEyecloud app................................................................................................... 72
17.
Specifications....................................................................................................................................... 73
18.
FAQ and maintenance ......................................................................................................................... 75
18.1
Maintenance..................................................................................................................................... 80
4
1. PRODUCT
1.1 Product overview
The series DVR is designed specially for security and defense field which is an outstanding digital
surveillance product. It introduces embedded LINUX operating system which is more stable. It introduces
standard H.264mp video compressed format and G.711A audio compressed format which insures the high
quality image, low error coding ratio and single frame playing. It introduces TCP/IP network technology
which achieves the strong network communication ability and telecommunication ability.
The series DVR can be used individually or online applied as a part of a safety surveillance network. With
the professional network video surveillance software it achieves the strong network communication ability
and telecommunication ability.
The series DVR can be applied in the bank, telecom, electric power system, judicial system, transportation,
intelligent housing, factory, storehouse, water conservancy and so on.
2. OPEN-PACKAGE CHECK AND CABLE CONNECTIONS
2.1 Open-package check
When you receive the DVR, please check first whether there is any visible damage to the package
appearance. The protective materials used for the package of the DVR can protect most accidental clashes
during transportation.
Then, please open the box and get rid off the plastic protective materials. Check whether there is any visible
damage to the DVR appearance.
At last, please open the machine crust and check the data wire in the front panel, power wire, the
connection between the fan power and the main board.
Front panel and rear panel
 The key function specification in the front panel and the interface specification in the real panel are
in the specification.
 Please check the product type in the front panel whether is accordant with the product type you
order.
The label in the real panel is very important for the after service. Please protect it carefully. When
you contact us for after service, please provide the product type and serial number in the label.
5
2.2 HDD installatation
Please install the Hard disk before the first time to use this product.
Please connect power cable and data cable of HDD correctly, our product can support 1 or 2 or 4
or 8 HDD, how many HDD can support is depends on which kind of product that buyer
purchase.(Remark: the device can run normally without HDD, but can not do record and
playback)
6
2.3 IIP-N410-N411S-N411SPOE-N4120-N3210-
1.
2.
3.
4.
Front
2. picture
Back
Indicator Leds
Menu button
Direction button
ESC
Network connector
(RJ45)
2. Switch
network
connectors (RJ45)
3. Video output VGA
1.
1. picture
4.
5.
6.
7.
8.
Video output HDMI
Video output BNC
On/Off button
Audio output RCA
USB ports
9. RS458 port
10. Power
supply
connector
The IIP-N410 back panel has no switch connectors.
The N411SPOE has a plus power suply connector to the switch adapter.
A termék specifikációk, paraméterek, funkciók előzetes figyelmeztetés nélkül megváltozhatnak!
7
2.4 IIP-N820
3. picture
11.
12.
13.
14.
15.
16.
On
Alarm
HDD
Alarm
Network
Status
17.
18.
19.
20.
21.
22.
Ready
Menu
PTZ
Search
Channel up
Channel down
4. picture
1.
2.
3.
4.
Video output BNC
Audio output RCA
Video output VGA
Video output HDMI
Előlap
23.
24.
25.
26.
27.
28.
Record
Play buttons
Esc
Menu buttons
ON\OFF
USB port
Back
Network connector
(RJ45)
6. USB ports
7. RS485 port
5.
Power
supply
connector
9. ON/OFF button
8.
8
2.5 IIP-N1640-N1641
0.
1.
2.
3.
4.
Menu button
Mode select
Search
PTZ control
FN button
5.
6.
7.
8.
9.
SHIFT button
ESC
Play buttons
ON/OFF button
USB port
1.
2.
3.
4.
5.
Video output BNC
Video output BNC
Audio output RCA
Video output VGA
Audio output RCA
6. Video output HDMI
7. Network connector
RJ45
8. USB port
9. Alarm in/out
10. Indicator Leds
11. Directions buttons
12. Jog dial
10. Power
supply
connector
11. Power switch
9
2.6 IIP-N2460-N2480
Play buttons
Menu buttons
ESC
Menu
FN
6. Shift button
7. Search
8. PZT button
9. ON/OFF button
10. Direction buttons
11. USB port
12. Jog dial
1.
2.
3.
4.
5.
1.
2.
3.
4.
5.
Video output BNC
Video output BNC
Audio IN/OUT
Power switch
FAN
6. Video output VGA
7. Video output HDMI
8. Network connector
RJ45
9. USB port
10. Alarm in/out
11. Power
supply
connector
10
2.7 Audio and video input and output connections
2.7.1
Video input connections
The video input port is BNC connector plug. The demand of input signal is PAL/NTSC BNC(1.0VP-P,75Ω).
The video signal must be accorded with the state standard which has the high signal to noise ratio, low
aberration and low interference. The image must be clear and has natural color in the appropriate
brightness.
Insure the vidicon signal stable and credible
The vidicon should be installed in the appropriate location where is away from backlighting and low
illumination or adopts the better backlighting and low illumination compensation.
The ground and power supply of the vidicon and the DVR should be shared and stable.
Insure the transmission line stable and credible
The video transmission line should adopt high quality coaxial pair which is chosen by the transmission
distance. If the transmission distance is too far, it should adopt shielded twisted pair, video compensation
equipment and transmit by fiber to insure the signal quality.
The video signal line should be away from the electro magnetic Interference and other equipments signal
lines. The high voltage current should be avoided especially.
Insure the connection stable and credible
The signal and shield lines should be firm and connected credible which avoid false and joint welding and
oxidation.
2.7.2
Video output connections and options
The video output is divided into PAL/NTSC BNC(1.0VP-P,75Ω) and VGA output(selective configuration).
When replace the monitor by the computer display, there are some issues to notice.
1、Do not stay in the turn-on state for a long time.
2、Keep the computer display normal working by demagnetizing regularly.
3、Stay away from the electro magnetic Interference.
TV is not a credible replacement as a video output. It demands reducing the use time and control the power
supply and the interference introduced by the nearby equipments strictly. The creepage of low quality TV
can lead to the damage of other equipments.
2.7.3
Audio signal input
Audio port is RCA connection.
The input impedance is high so the tone arm must be active.
The audio signal line should be firm and away from the electro magnetic Interference and connected
credible which avoid false and joint welding and oxidation. The high voltage current should be avoided
especially.
2.7.4
Audio signal output
Commonly the output parameter of DVR audio signal is greater than 200mv 1KΩ(RCA) which can connect
the low impedance earphone and active sound box or other audio output equipments through power
amplifier. If the sound box and the tone arm can not be isolated, howling phenomena is often existed. There
are some methods to deal with the above phenomena.
 Adopt better directional tone arm.

Adjust the sound box volume to be under the threshold that produces the howling phenomena.

Use fitment materials that absorb the sound to reduce reflection of the sound.

Adjust the layout of the sound box and the tone arm.
11
2.7.5
Alarm input and output connections
Alarm input
A. Alarm input is grounding alarm input.
B. Alarm input demand is the grounding voltage signal.
C. When the alarm is connected with two DVRs or connected with DVR and other equipments, it should be
isolated by relay.
Alarm output
Alarm output can not be connected with high-power load (no more than 1A).When forming the output loop it
must prevent the big current from relay damage. Use the contact isolator when there is a high-power load
PTZ decoder connections
A. The grounding of the PTZ decoder and DVR must be shared otherwise the common-mode voltage will
lead to the PTZ control failure. The shielded twisted pair is recommended.
B. Avoid the entrance of high voltage. Make the layout reasonably. Take precaution from the thunder.
C. In the outlying end connect 120Ω resistance paralleled to reduce the inflection and insure the signal
quality.
D. The 485 AB lines of DVR can not connected with other 485 output equipments paralleled.
E. The voltage between the AB lines of the decoder must be less than 5V.
Front equipment grounding note
Bad grounding can lead to the burnout of the chip.
Alarm input type unlimited
The DVR alarm output port is constant opening type.
(1) alarm input (2) grounding (3) RS232 (4) alarm output (5) RS485
parameter
G
C1、NO1
T、R
A、B
2.7.6
meaning
grounding
Alarm output interface(constant open
type)
RS232 port
485communication interface which is
connected with the recording control
equipments such as the decoder
Alarm input port specification
1 channels alarm input. Alarm input type unlimited.
12
The grounding and the com port of the alarm sensor are parallel (The alarm sensor is external power
supply) .
The grounding of the alarm and the DVR should be shared.
The NC port of the alarm sensor must be connected with the DVR alarm input port.
The grounding of the power supply and the alarm sensor must be shared when used in external power
supply.
2.7.7
Alarm output port specification
1 channels alarm output. There is external power supply when using the external alarm equipment.
Please refer to the relay relevant parameters to avoid the overload that damages main machine.
2.7.8
Alarm output port relay parameters
Type：JRC-27F
Interface material
rating
(resistance load)
maximal switch power
maximal switch voltage
maximal switch current
isolation
Inhomo-polarity interface
Interface and winding
Surge voltage
Turn-on time
Turn-off time
longevity
electric
Environment temperature
silver
Rating switch
30VDC 2A, 125VAC
capacity
1A
125VA 160W
250VAC, 220VDC
1A
Homo-polarity
1000VAC 1minute
interface
1000VAC 1 minute
1000VAC 1 minute
Homo-polarity
1500VAC (10×160us)
interface
3ms max
3ms max
mechanical
50×106 MIN（3Hz)
200×103 MIN (0.5Hz)
-40~+70℃
2.7.9
Speed dome connections
Step 1.
Connect the 485 lines of the speed dome with the DVR 485 interface.
Step 2.
Step 3.
Connect the video line with the DVR video input.
Electrify the speed dome.
13
2.8 Turn on
Connect with power, turn on the switch at the back panel, the indicator is on, then DVR was turned on. After
starting up, you can hear a beep, the default output mode is multi-window mode. Remark: Restart the power
after the abnormal power off, DVR will automatically recover the state before power off.
Note:
 Make sure that the input voltage corresponds with the switch of the DVR power supply.
 Power supply demands: 220V±10% /50Hz.
Suggest using the UPS to protect the power supply under allowable conditions.
2.9 Turn off
There are two methods to turn off the DVR. Entering [main menu] and choosing [turn off] in the [turn off the
system] option is called soft switch. Pressing the power supply switch is called hard switch.
Illumination:
2.9.1
Auto resume after power failure
If the DVR is shut down abnormally, it can automatically backup video and resume previous working status
after power failure.
2.9.2
Replace the hard disk
Before replacing the hard disk, the power supply switch in the real panel must be turned off.
2.9.3
Replace the battery
Before replacing the battery, the setting information must be saved and the power supply switch in the real
panel must be turned off. The DVR uses button battery. The system time must be checked regularly. If the
time is not correct you must replace the battery, we recommend replacing the battery every year and using
the same battery type.
Note: The setting information must be saved before replacing the battery otherwise information will lose.
14
2.10 Login
When the DVR boots up, user must login and the system provides the corresponding functions with the user
purview. There are two user settings which are admin, and guest; and they have no passwords. “Admin” is
the super user purview; “Guest” is the user for preview and playback. User can modify the password of
Admin and Guest, but can not modify the authority of them.
3 deafult profil: admin, gues, default
There is no default password, the admin is the super authorized user at default. For the guest and the
default login are enabled to use the preview and play functions. The admin and the guest can modify the
password, but the permissions not. By default the default login can change the authorization, but the
password not.
5. picture
Login
Note: Password alert: If the password incorrect in 3 times, it generates an alarm. After 5 times, it
lock the recorder for 1,5 hour (please reboot the device after this).
Please change the password at the first login!
Only service can change the forgotten password!
15
2.11 Plug&Play (Wizard)
When the recorder starts, there is a wizard, which can help you to access and cofigure the cameras in an
easy way.
The products with POE function has a Plug&Play option. With this feature is it possible to configure every
settings without any IP settings before that.
Note: The default IP address of the recorder is 192.168.1.1. After changing it, please reboot the device. This
is necessary to the normal functions.
6. picture
Guide
Step 1.
Choose the Cloud Enable function (if there is no need this wizard next, click on will no longer
br prompted)
Step 2.
Click on the Next option.
Step 3.
After a short search time, the available cameras will be shown on the screen.
Step 4.
Click on the OK button.
7. picture
Ip config wizard
Step 5.
Only with ONVIF compatible cameras- choose the ONVIF option on the left side (instead of
NETIP) and click on the Search option. After a short search time the ONVIF cameras will be shown
on the screen. Clik on the Ok button.
2.12 Plug&Play (Wizard) 2.
There are some new devices that have a newer guide option.
Step 1.
Choose the Cloud Enable function (if there is no need this wizard next, click on will no longer
br prompted)
16
Step 2.
Click on the Next option.
8. picture
Step 3.
Step 4.
Step 5.
Step 6.
Mode selection
Click on the Manual mode.
In the next window you can see the available devices.
Click on the device that will be added to the first channel and double click on it.
Make these steps to all cameras.
9. picture
Step 7.
IP config wizard
When finished click on the OK button and the cameras are ready.
3. REMOTE CONTROLLER
No.
Name
Function
1
Multi-channels
button
Multi-channels preview
2
Number button
Password input/number input/ channel switch
17
3
【Esc】
Back to up window
4
Direction button
Direction and OK button
5
Playback operate
Playback Basic operation
6
Record control
Enter into record menu
7
Remote controller
Input the number of DVR to control it
8
FN
Assistant function
4. MOUSE OPERATION
Operation
Function
Double left click
Double click one item in the file list to playback
the video
Double click the playback video to zoom in or
out the screen
Double click the channel to make it full screen
display in preview
double click again to resume the multi-channel
display
Left click
Choose according option in the menu
Right click
Pop desktop shortcut menu in preview state
Current shortcut menu in the menu
Wheel button
Add or subtract number value in the number setting
Switch the items in the combo box
Page up or down in the list
Move mouse
Choose the widget or move the item in the widget
Drag mouse
Set the motion detect area
Set the cover area
18
5. PREVIEW
10. picture
1.
2.
3.
Preview
Control buttons
Channel properties
Channel select
The system date, time and channel title are shown in each viewing window. The surveillance video and the
alarm status are shown in each window.
5.1.1
Control buttons
Record buttons
1
Recording status
3
Video loss
2
Video motion
4
Camera lock
19
6. DESKTOP SHORTCUT MENU
In preview mode you can right click mouse to get a desktop shortcut menu. The menu includes: main
menu, record mode, playback, PTZ control, High Speed PTZ, Alarm Output, color Setting, Output
adjust, Logout, view1/4/8/9/16 screens.
11. picture Desktop shortcut menu
6.1 Menu
When you login, the system main menu is shown as below.
12. picture Menu
20
6.2 Playback
There are two methods for you to play the video files in the hard disk.
 In the desktop shortcut menu.
 Main Menu>Record>Playback.
Enter the playback interface, you can playback video of multi-channels at the same time.
Note: The hard disk that saves the video files must be set as read-write or read-only state.
13. picture
1. Playback control
buttons
5. Time mode
select
9. Search by time
2. Time
6. Search by hour
10. Search by storage
Playback
3. Sync
7. File type
4. Video type
8. Listed files
11. Serach by
12.Seach by
date
channel
21
6.2.1
Playback control
Button
Function
Button
Function
/
Play/Pause
Reverse Play
Stop
Slow play
Reverse fast play
Fast play
Previous frame
Next frame
Previous file
Next file
Ciculation
Fullscreen
Cut
Save
6.3 Backup
14. picture
Backup
Step 1.
Plug a pendrive\portable winchester to the USB port of the device.
Step 2.
Choose the [Menu]-[Record]-[Save] menu (there can be a short waiting time).
Step 3.
Choose the device and click on the Save option. After this a new windows will pop up (see
the chapter)
Detect: Detect the storage connected with the DVR such as hard disk or universal disk.
Erasure: Choose the file to delete and click erasure to delete the file.
Stop: Stop the backup.
Backup: Click backup button and the dialog box is popped up. You can choose the backup file according to
the type, channel and time.
22
6.4 Record backup
15. picture
Backup
Step 1.
Choose the right type of the recording (or leave on the ALL option).
Step 2.
Choose the channel number.
Step 3.
Choose the time which will be saved.
Step 4.
After a short time, it will be shown which records are available for the period. Click on the
right file (or select more) and click on the Start button.
Step 5.
The record are downloading to the pendrive (it can be a long time, depending on the
recorder file size).
1 hour record is between ~600MB and 3,5GB (depends on the quality of the record)
Bad quality
2000KB/s
~600MB
Good quality
4000KB/s
~1.7GB
Best quality
8000Kb/s
~3.5GB
500GB harddrive good quality, 1 camera ~300 hour recording (~12 days)
500GB harddrive good quality, 8 camera ~37 hour recording (~1,5 days)
1TB harddrive good quality, 1 camera ~600 hour recording (~24 days)
1TB harddrive good quality, 8 camera ~74 hour recording (~3 days)
Remove：Clear the file information.
Add：Show the file information satisfying the set file attributes.
Start/Pause：Click the play button to start the backup and click the pause button to stop the backup.
Cancel：During backup you can exit the page layout to carry out other functions.
23
6.5 Recorded files playing on a PC
The recorded files can be watched on the PC:
Step 1.
Install the Disc Player software from the CD.
Step 2.
After the installing, start the program. Click on the play button and choose which file will be
watched.
Step 3.
On the PC there are the same functions when playing a file as on the recorder (slow, fast
play,...)
1. H264 Player
6.6 Files Convert
Step 1.
Start the Video Converter Tool software (there is no need to install the program, it can be
found on the CD).
Step 2.
Click on the Open button and the choose the file(s) will be converted.
Step 3.
Click on the Settings menu and choose the right option.
Step 4.
Click on the convert button and wait for to finish.
2. Video converter tool
24
3.
6.7 Record mode
Please check current channel status: “○” means it is not in recording status, “●” means it is in recording
status.
You can use desktop shortcut menu or click [main menu]> [recording function]> [recording set] to enter the
recording control interface.
16. picture
Record mode
[Schedule] Record according to the configuration.
[Manual]Click the all button and the according channel is recording no matter the channel in any state.
[Stop] Click the stop button and the according channel stops recording no matter the channel in any state.
6.8 Color settings
Set image parameter of chosen channel (when single view preview, it should be current channel, when
multi-view preview, it should be the channel where the cursor stay), you can enter the page by shortcut
menu. Image parameters including: brightness, contrast, saturation, hue, gain, horizontal and vertical
sharpness. Also you can base on requirement to set different image parameter in different period.
The color adjustment contains the following:
 Brightness
 Contrast
 Saturation
 Hue
 Strenght
 Horizontal and vertical sharpness
17. picture
Color settings
6.9 Output Adjust
Adjust TV output area parameters. You can use the desktop shortcut menu or enter [main menu]>
[management tools]> [Output adjust].
25
18. picture
Output adjust
6.10 PTZ control
Operation interface is as followed. The functions include: PTZ direction control, step, zoom, focus, iris, setup
operation, patrol between spots, trail patrol, boundary scan, assistant switch, light switch, level rotation and
so on.
19. picture
PTZ control
Note:
 Decoder A(B)line connects with DVR A(B)line. The connection is right.
 Click [main menu] >[system configuration] >[PTZ setup] to set the PTZ parameters.
 The PTZ functions are decided by the PTZ protocols.
[SpeedSet] the PTZ rotation range. Default range: 1 ~ 8.
[Zoom] Click -/+ button to adjust the zoom multiple of the camera.
[Focus] Click -/+ button to adjust the focus of the camera .
[Iris] Click -/+ button to adjust the iris of the camera.
[Direction control] Control the PTZ rotation. 8 directions control is supportive.(4 directions in Front panel is
supportive )
[High speed PTZ] Full-screen show channel image. Left press mouse and control PTZ to rotate orientation.
Left press mouse and then rotate the mouse to adjust the zoom multiple of the camera.
[Set] Enter the function operation menu.
[Page switch] Switch between different pages.
26
6.11 PTZ Special functions：
6.11.1 Preset
Set a location for the preset, calls the preset points, PTZ automatically turns to the setting position
Preset option
Set a location for the preset, procedure is as follows:
Step 1.
click the Direction button will turn into preset position , click the Settings button to enter
Step 2.
click the Preset button , then write the preset points in the input blank,
20. picture
PTZ config
Step 3.
click Settings button, return the Complete setup, that is the preset points and preset position
corresponds.
Clear Preset：Input preset points, click Remove button, remove the preset
Preset Point Calls
Step 1.
click Page Shift button
Step 2.
enter PTZ control interface
Step 3.
In the input blank, write the preset points, then click Preset button
Step 4.
PTZ turn to the corresponding preset point.
21. picture
PTZ control
6.11.2 Cruise between Points
Multiple preset points connected cruise lines, call cruise between points, the PTZ run around on the line
27
Cruise Between Points Settings
Cruise lines is connected by multiple preset points, setting procedure is as follows:
Step 1.
the Direction key will turn PTZ to designated location , click Settings button to enter
Step 2.
click Cruise buttons, the write proper value into the Cruise Line and Preset Points
blank，then click Add Preset Points button, complete setting (also can add and delete cruise line
which has been set up)
Step 3.
repeat step1 and step2 , until set out all the preset designated cruise lines
Remove Preset：Please input preset value in the blank, click Remove Preset button, then remove the
preset points.
Remove Cruise Line：Input the number of cruise line, click Remove Cruise Lines button, then remove the
cruise lines set
22. picture
Cruise Between Points Settings
The Calls of Cruise between Points
Step 1.
click Page Shift button, enter PTZ control menu as shown
Step 2.
Please input the number of cruise in the value blank, then click Cruise between Points button
Step 3.
PTZ begins to work on the cruise line.
Step 4.
Click Stop button to stop cruise.
6.11.3 Scan
PTZ also can work on the preset scan line repeatedly.
Scan setup
Step 1.
click Setup button, enter
Step 2.
Click Scan button，the input proper value in the scan value blank;
Step 3.
Click Start button, enterhere you can set the following items:
Zoom、Focus、Aperture、Direction and so on. Click Setup button to go back
Step 4.
Click End button to complete setup
Step 5.
Click the right button of the mouse to exit.
28
23. picture
Scan Calls
Step 1.
Step 2.
Step 3.
Step 4.
Scan setup
click Page Shift button, then enter PTZ control menu as shown in Picture
Please input the number of scan in the value blank , then click Scan button
PTZ begins to work on the scan line.
Click Stop button to stop.
6.11.4 Boundary Scan
Boundary Scan setup
Step 1.
click Direction button to turn the PTZ to preset direction, then click Setup button enter select
the left boundary, return
Step 2.
Please click direction arrows to adjust PTZ direction, click Setup button enter then select the
right boundary ,return
Step 3.
Complete setup, that is the position of left and right boundary
24. picture
Boundary Scan Setup
Boundary Scan Calls
Step 1.
click Page Shift button, then enter PTZ control menu as shown in Picture
Step 2.
Please input the number of scan in the value blank , then click Scan button
Step 3.
PTZ begins to work on the scan line
Step 4.
Click Stop button to stop.
6.11.5 Horizontal Rotating
Click Horizontally Rotating button, PTZ begins to rotate horizontally (relative to the original position of the
camera). Click the Stop button to stop.
29
6.11.6 Rotate
Click on horizontal Rotating button, PTZ turn around.
6.11.7 Reset
PTZ restart, all the data clears to 0.
6.12 Logout
Logout, shut down the system or reboot up. You can use the desktop shortcut menu or enter [main menu].
25. picture
Logout
[logout] Quit the menu. Offer password next entrance.
[shut down] Quit the system. Turn off the power supply.
When press the shut down button, there is schedule hint. After three seconds, the system is shut down.
Cancel midway is of no effect.
[reboot] Quit the system. Reboot up the system..
30
7. RECORD MODE
Set the recording parameters in the surveillance channel. You can enter [Main Menu]> [Record]> [Record
Config] to set. The system’s default set is 24 hours continuous recording.
Note: There is at least one read-write hard disk if the DVR records normally
[Channel] which channel settings are activated
[Redundancy] Select this mode, if you would like to backup the video sin two hard disks (only with two hard
disks)
[Length] video files duration
[Pre-recording] not working function
[Record mode] timing, power, stop
[Period] Set a time frame of when to record
[Allways] recording all-time
[Move] only recording when motion is detected
[Alarm] only recording when alarm is activated
26. picture
Record config
7.1 Snapshot storage (Partial model support)
Base on settings to save the monitor image
Parameter setting:【Main menu】>【Record】>【Snapshot】to do related setting, see pic 3, the function is
closed in default.
Note: If normal snapshot storage, please set Snap at 【Main Menu】->【Advanced】->【HDD Manage】>【Snapshot】
31
27. picture
Snapshot storage
【Channel】Select the related channel to set,click "all" to set all channels.
【Presnap】Setup presnap picture quantity before recording, default is 5 pieces.
【Record】Set record status,"Schedule","Manual" and "Stop" Page 32
Schedule:Realise snapshot according to record type(regular,detect and alarm) and period.
Manual:No matter what the present channel is in a state,once choose "manual" button,it will have snapshot
at related channels.
Stop:No matter what the present channel is in a state,once choose "stop" button,it will stop snapshot at
related channels.
【Period】Set normal record period,it only startup Snapshot Storage at set period.
【Type】Three types:regular,detect and alarm
【Record type】Three types:regular,detect and alarm
Regular: snapshot at set period
Detect: snapshot at set period when motion detect,video blind and video loss which are preset for snapshot
enable.
Alarm:snapshot at set period when alarm in which is preset for snapshot enable.
32
8. ALARM
28. picture
Alarm
8.1 Video motion
When the system detects the motion signal that reaches the sensitivity, the motion detection is activated.
[Channel] which channel settings are activated
[Activation] function activation
[Sensitivity] set the sensitivity for the right option
[Area] Click on Settings, and set the area control (the light blue is the guarde, dark blue is ungarded area)
[Period] Set a time frame of when to record
[Alarm output] select the alarm output
[Record channel] select the channel which would you like to record
[Step] step selection
[Delay] When alarm is over, recording will last some seconds (10~300sec), then stop
[Snapshot] snapshot activation
The snapshot can be linked to enable the motion detection in the corresponding period of the [Record
Setting] in (recording settings).
[PTZ activation] when alarm is detected, the PTZ option can be activated (for this option please first set
the right PTZ options in he [PTZ control]
[Email] when alarm happen, link email sending to inform user.
Note: sending email, need to do related setting at[Net service]
[FTP upload] when alarm happens, if record or snapshot channel was chosen, the record file and snapshot
image will be uploaded to the appointed position.
Note: FTP upload, need to do related setting at[Net service]
33
29. picture
Video motion
8.2 Video blind
When the video image disappear because of the poor brightness or by masking, the video blind is activated.
Settings are described in the motion detection function.
30. picture
Video blind
34
8.3 Video loss
When the vide image disappear the video loss is activated.
Settings are described in the motion detection function.
31. picture
Video loss
32. picture
Abnormal
8.4 Abnormal
There are abnormal events which can trigger an alarm.
 Storage problem
 Low storage capacity
 Storage access problem
 IP address problem
 Network problem
[Activation] function activation
[Message] message on the main screen
[Buzzer]
35
9. SYSTEM SETUP









General options
Encoding
Network
Net service
Gui option
PTZ configuration
Digital settings
RS485, RS232 options
Camera parameters
9.1 General
33. picture General settings
[System time] system date and time settings
[Date format] select the date format
[Date separator] choose the separator of the data format
[Time format] select the time format
[Language] Hungarian, English, Chinese, Italian, Spanish, Russian, French, German, Portuguese, Polish,
Suomi, Greece
[HDD full]
[DVR No.] with more recorders is it possible to choose them with the right button in the remote control
[Video standard] PAL or NTSC
[Auto logout] automation logout after the set time
36
9.2 Network settings
34. picture Network settings
[Net card] wireless or wired land card (check if the wireless is available in the specification)
[DHCP Enable] automatic IP address configuration
[IP address] IP address settings default: 192.168.1.10
[Subnet mask] default: 255.255.255.0.
[Gateway] default: 192.168.1.1
[DNS settings] option to use a DNS server, which converts the IP address to DNS address. Reboot after
set.
[TCP port] default: 34567 for CMS access
[HTTP port] default 80 for Internet Explorer access
[High speed download] Network high speed download
[Quality strategy] there are 3 policies, adaptive, quality preferred, fluency preferred. Base on different
setting, code stream is auto-adjusted, adaptive is eclectic between quality and fluency, also considers
fluency when the quality is not greatly influenced. Fluency preferred and adaptive is valid only when the
extra stream is enabled, if extra stream is not enabled, it will base on network status to adjust quality
preferred
Note: Changing the IP address in a POE compatible recorder, make sure to reboot after that!
37
9.3 Netservice
35. picture NetService
[PPPoE settings]
Click on the activate and write the user name and the password, which provided by the ISP (Internet Service
Provider). Reboot after set and the record will make a PPPoE connection with ISP. The IP address will
change to dynamic.
36. picture
PPPOE
[NTP setup]
First the NTP server will be installed on the PC or use a public NTP server.
Server Ip: write the server IP address.
Port: default: 123
Time zone: London GMT+0, Berlin GMT +1, Cairo GMT +2, Moscow GMT +3, New Delhi GMT +5,
Bangkok GMT +7, Hongkong Beijing GMT +8, Tokyo GMT +9, Sydney GMT +10, Hawaii GMT-10,
Alaska GMT-9, Pacific time GMT-8, American mountain time GMT-7, American mid time GMT-6,
American eastern time GMT-5, Atlantic time GMT-4, Brazil GMT-3, Atlantic mid time GMT-2.
Refresh time: default: 10 Min.
38
37. picture
NTP setup
[EMAIL settings]
When an alarm is triggered, the recorder can send an email with the alarm informations.
38. picture E-mail settings
SMTP server: email account provider SMTP server address (IP or DNS address)
Port: email account port number
SSL: secured socker layer protocoll activation
User name: email user name
Password: email password
Sender: write a sender name
To: write an email address which you would like to send the emails.
Subject: write an email subject.
[IP filter settings]
White addresses: devices with these IP addresses can access the recorder only. (64 IP addresses is
available)
Black addresses: devices with these IP addresses can not access the recorder (64 IP addresses is
available)
39
39. picture IP filter
[DDNS]
Dynamic Domain Name System
DDNS type: set the right option
Enable: set to activate
DNS name: write the DNS address
User name: write the user name
Password: write the password
When DDNS is activated and ready, you can access with this address from the Internet Explorer.
40. picture
DDNS settings
[FTP Settings]
Server IP: server IP address
Port: FTP server port number
User name: write the user name
Password: write the password
File size: Set the max upload file size to. default: 128MB
Order name: upload order name
40
FTP upload is only possible when alarm is activated. When the alarm time is over, the uploading is
automatic.
41. picture
FTP settings
[Alarm server]
When alarm is activated, the alarm server receives information from the device.
Protocoll type: set the right option, default: General
Server IP: IP address of alarm server
Port: port address
Alarm: set to activate
History: set to activate
[Wi-Fi settings]
42. picture
Wifi settings
41
Search: You can search for Wi-Fi networks in your area
SSID: The name of the used Wi-Fi network
Encryption: type of encryption (suggest to use WPA2)
Password: the preshared key of the Wi-Fi network
IP address: IP address of the camera
Subnet mask: Subnet mask of the actual network
Gateway: the gateway of the network
3G: optional with 3G compatible router (example:TP-LINK TL-MR3420)
[Mobil Monitor settings]
To visit the device by mobile, please make a router mapping of this port and use CMS to monitor and
operate it by protocol.
Port: default port: 34599
43. picture
Mobil monitor Port forward
[UPNP]
UPNP protocol can auto port forwarding on router, make sure UPNP is enable on router before use it.
44. picture
UPNP
Http port: Route will automatically distribute HTTP port for the device, when IE viewing, it need this port
Az Internet Explorer –es kéréseket automatikusan a DVR-re írányítja a Router
TCP port: Router will automatically distribute TCP port for the device, when monitoring via CMS
Port: Router will automatically distribute Mobile Port for the device, when mobile monitor
42
[Cloud]
Cloud settings and activation.
MTU: default: 1280 Byte
[PMS]
PMS cloud access.Please do not change these settings (just enable)!
45. picture
PMS settings
43
9.4 GUI display
46. picture GUI Display settings
[Channel Name] Click the channel name modify button and enter the channel name menu. Modify the
channel name.
[Time title] the system time on monitoring pag
[Channel title] channel No at monitoring page
[Record status] record status on monitoring page
[Alarm status] alarm status on monitoring page
[Transparency] choose the transparency of background image, span within: 128~255
[Resolution] set resolution of monitor
[Channel] choose channel No that set for encode output.
[Region Cover] choose region cover quantity, then click setting
，enter
related channel, user can use mouse to choose any size of cover region, (the covered region, video output
should be in black)
[Time title]& [Channel title] set time title and channel title whether need be show out and the position to
show.
44
9.5 Tour setup
Set the patrol display. You can choose the single window, four windows, nine windows, sixteen windows
patrol display or single display.
[Interval] Set the patrol switch interval. The set range is 5-120 seconds.
Note： / means turn off/on the patrol.
47. picture
Tour setup
10. ADVANCED







HDD manage
Account
Auto Maintain
Default
Import & Export
Upgrade
Reboot
10.1 HDD manage
Configure and manage the hard disk. The menu displays current hard disk information: hard disk number,
input port, type, status and overall capability. The operation include: setup the write-read disk, read-only
disk, redundant disk, hard disk format, resume default. Choose the hard disk and click the right function
button to execute.
Note：
 Read/Write Disk:The equipment can write or read data.
 Read-only Disk:The equipment can read data but can not write data.
 Redundant Disk:Double backup the video files in the write-read disk.
45
48. picture
HDD manage
10.2 Account
Manage the user purview.
49. picture Account settings
Manage the user authority of this device.
Note:
1. The character length is 8 bytes at most for the following user and user team name. The blank ahead
or behind the character string is invalid. The middle blank in the character string is valid. Legal
characters include: letter, number, underline, subtraction sign, and dot.
2. There is no limit in the user and user group. You can add or delete the user group according to user
definition. The factory setup include: user\admin. You can set the team as you wish. The user can
appoint the purview in the group.
3. The user management include: group/ user. The group and user name cannot be the same. Each
user only belongs to one group.
46
50. picture Password change
[Add user] Add a user in the team and set the user purview. Enter the menu interface and input the user
name and password. Choose the team and choose whether cover using the user. Cover using means that
the account can be used by multiple users at the same time.
Once choose the team the user purview is the subclass of the team.
We recommend that the common user’s purview is lower than the advanced user
51. picture Ad account
Add Group: Add a user team and set the purview. There are 36 different purviews: shut down the
equipment, real time surveillance, playback, recording setup, video file backup and so on.
Note: Please dicuss with the customer, which functions need to be enable. (These user account has
no access to these features: record saving, record settings, alarm settings)
47
52. picture Add group
[Delete user] Delete the current user. Choose the user and click delete user button.
[Delete Group] Delete the current group. Choose the group and click delete group button.
53. picture Group delete
10.3 Online user
Look up the network user information in the local DVR. You can choose the network user and cut the
connection. Then the user is locked until next boot-strap.
48
54. picture
Online user
10.4 TV settings
Chapter 6.9.
10.5 Auto-maintain
The user can set the auto reboot time and auto file deleting time limit.
55. picture Auto-maintain
10.6 Restore
The system restore to the default setup. You can choose the items according to the menu.
49
56. picture Restore
10.7 Upgrade
57. picture Upgrade
.
[Upgrade file] to select upgrade file via IE or client software to do upgrading.
10.8 Device info
Provide device interface info like audio in,alarm in/out to be conveniently used for user.
50
58. picture
Device info
10.9 Import/export
It is possible to import or export settings from the recorder to a pendrive or harddrive.
59. picture
Import/export
11. INFO MENÜ
HDD info, BPS, Log, version
11.1 HDD információ
It shows the infos abbout the HDD. (type, capacity, remaining space, status)
51
60. picture HDD information
Clue: means that the hard disk is normal. X means that the hard disk is broken-down.- means that there is
no hard disk. If the user need to change the damaged hard disk, you must shut down the DVR and take up
all the damaged hard disks,then install a new one.
* behind serial number means the current working disk such as 1*. If the corresponding disk is damaged,
the information will show “？”.
11.2 BPS
Display the code stream（Kb/S）and hard disk capability （MB/H）in real time. It displays as the wave
sketch map.
61. picture BPS infomation
52
11.3 Log
Look up system log according to the set mode.
Log information include: system operation, configuration operation, data management, alarm affair,
recording operation, user management, file management and so on. Set the time section to look up and
click the look up button. The log information will display as a list. (one page is 128 items) Press Page up or
Page down button to look up and press delete button to clear all the log information.
62. picture Log
11.4 Version
Display the basic information such as hardware information, software edition, issue data and so on.
53
63. picture
Version
54
12. DIGITAL CHANNELS
12.1 Basic knowledge
[IP address] two functions: host or network interface identification (IP address example: 192.168.1.110)
Two versions of IP are in use: IP Version 4 and IP Version 6. Each version defines an IP address differently.
Because of its prevalence, the generic term IP address typically still refers to the addresses defined by IPv4.
[TCP port] Internet protocoll, which helps the datatransfer.
[DHCP] clien-server protocoll, which provide to the network using devices to get every information
automatically by the DHCP server. It provides the IP addresses for the cameras, when it is enabled.
[Fix or static IP address] these type of IP address will not change after a system reboot.
[POE] Power over Ethernet describes any of several standardized or ad-hoc systems which pass electrical
power along with data on Ethernet cabling. This allows a single cable to provide both data connection and
electrical power to devices such as wireless access points or IP cameras. These feature is in every
compatible device’s specifications.
The maximum compatible cable long for the POE is 100 m.
We have tested the N411SPOE recorder with a 100m good quality solid copper Belden cable (FTP
connectors). It had no problems, but please make sure that every situation is different and the compatible
long can decrease because of the installations methods.
55
12.2 First steps
First connect the cameras to the power supply and to the network, after this make sure that the devices
have static IP addresses (at default they have, but its the same, we have change that). This steps are not
necessary, but provide a stable network connection.
These steps are showed by a system with a TP-link router and an NVR recorder. Other manufactures
have the same solutions, but the steps can be different.
First find out what is your router default IP address (it is written on your router, or in the setting
menu)
64. picture
Router settings
Default IP address: 192.168.1.1
Subnet Mask: 255.255.255.0
Router Mac address: F4-EC-38-CC-8A-5A
12.3 Static IP address to the Cameras
12.3.1 Add device to CMS software
To make these steps, the devices have to be in the same IP region as the router ( the default region for the
cameras is 192.168.1. ...). If it is not, please make the next chapter steps first.
Step 1.
Install the CMS software from the CD, on a PC that is on the network as the cameras.
Step 2.
Log-in to the CMS software.
user: super
password:(default none)
65. picture
Step 3.
CMS program
Choose the System, and click on the Device Manager.
56
66. picture
Step 4.
…).
CMS software menu
Choose the Add Region and write an optional region name (example: Home, Office, Storage,
67. picture
Step 5.
Add region
Choose the region, and click on the add device option.
68. picture
Add Device
Step 6.
On he new screen click on the IP Search option. After the searching time, it will show the
available devices.
57
69. picture
Step 7.
IP Searc
Choose the device, which will be used (double click, and the fields will be automatically filled)
70. picture
Camera network settings
Note: If there are no devices after the search, probably there is a network problem. Please make sure
that the network settings are good, or the devices have installed correctly. (It can cause problems a
broken UTP cable, make sure to test every network cable with an UTP tester).
Other problem can be, that the devices are not in the same network region. (example: IP addresses:
router: 192.168.0.1, device 192.168.1.10). In this case use the Upgrade Tool software to change IP
addresses of the devices.
Step 8.
Click on the OK button when finished. If every settings are correct, the cameras picture can
be watched in the program. Choose the left side the region and the name\IP address of the camera
and double click on it.
58
71. picture
Camera picture
12.3.2 Static IP address with Upgrade Tool
Step 1.
Download or install from the CD the Upgrade Tool software.
Step 2.
Click on the IP search option.
59
72. picture
Upgrade Tool
Step 3.
It shows the IP address of the available IP cameras. Click on the camera which will be
modified and click on the Edit Device option.
Step 4.
In the pop up windows set up the right network parameters.
73. picture
Edit device
[IP address] At default is 192.168.1.10, this has to be changed to the right IP address.
[Gateaway] Write the IP address of the router.
(Example for a network system:
Router: 192.168.1.1
Camera 1: 192.168.1.10
Camera 2: 192.168.1.11
Camera 3: 192.168.1.12
For the same network devices(computer, camera, laptop, tablet) please avoid the same IP addresses,
because it will causes problems.
Please do not change the other settings, only if you are an expert.
60
12.3.3 Static IP address with CMS
Step 1.
Click on the Settings menu and choose the remote settings.
74. picture
Remote settings
Step 2.
Choose on the left side to which camera will be modified. Click on the Settings and the
Network option.
75. picture
Network options
Step 3.
In this window can be modified the network settings to the device.
Step 4.
First click out the DHCP Enable option.
[IP address] At default is 192.168.1.10, this has to be changed to the right IP address.
(Example for a network system:
Router: 192.168.1.1
Camera 1: 192.168.1.10
61
Camera 2: 192.168.1.11
Camera 3: 192.168.1.12
For the same network devices(computer, camera, laptop, tablet) please avoid the same IP
addresses, because it will causes problems.
Please do not change the other settings, only if you are an expert.
76. picture
Network settings of the device
Step 5.
Note: If the camera will be used on the CMS program after that, it has to to search again, because the IP
address was changed.
12.3.4 Port forwarding
Please use this feature, if your router does not have a UPNP option, otherwise these steps are
unnecessary.
77. picture
Router UpnP settings
62
78. picture
Enable the UPNP feature on the device too!
Port forwarding steps.
Step 1.
Log-in to the router admin screen. (Write the IP address of the router to the browser)
Default IP addresses for different type of routers (Please check in your router’s manual guide)
TP-LINK:http://192.168.1.1 vagy http://192.168.0.1
D- link:http://192.168.0.1
Linksys:http://192.168.2.1
Asus:http://192.168.2.1
ZTEhttp://192.168.1.254)
79. picture
Step 2.
Router admin screen
Choose the Forwarding option and click on the Add new option.
80. picture
Virtual servers
63
Step 3.
Write the right settings.
[Service Port] default port: 34567
[IP Address] IP addresses for the camera (pl: 192.168.168.10)
[Protocol] ALL-TCP-UDP
[Status] set to Enable
Do not change the Common Service Port!
81. picture
Virtual server settings
Lépés5: A Virtual Servers oldalon láthatjuk is, hogy melyik portot aktiváltuk az adott kamerára.
Step 4.
Click on the Save option, and the settings for the first device is finished.
82. picture
Virtual server settings
If you have more devices, repeat these steps to every one (make sure that you use the right IP
addresses for the devices)
Step 5.
Reboot the router. (System Tools-Reboot option)
83. picture
Router reboot
64
Asus Virtual Server
84. picture
Asus router
85. picture
D-link router
86. picture
Belkin router
D-Link Virtual Server
Belkin Virtual Server
65
87. picture
12.4 Recorder settings
The next step is to set the right settings to the router.
Step 1.
Step 2.
Step 3.
Step 4.
Step 5.
Step 6.
Log-in to the recorder, click on the Channel mode.
Choose the right option for your system. (There are just only fix modes)
Click on the left side to activate the mode.
The device will ask for reboot, click on the OK button.
After this, there are 2 more options in the Digital options (only with HVR recorders)
88. picture
Channel mode settings (HVR with 4 channel)
12.5 Digital channels
12.5.1 Add camera to the recorder
89. picture
Digitális channels
Step 1.
Click on the channel which will be modified.
Step 2.
Click on the Enable option.
Time Sync- camera-recorder time synchronization
Encode: default: real-time 2
Connection type: default: Only one connection
Step 3.
Select the Add button.
Step 4.
In the new screen can be changed the camera settings.
66
90. picture
Remote settings
Click on the Search option, and double click to the camera which will be used for the channel. (It will
fill the requiered forms, if it is not, please write the settings to the form).
Device name: optional
Device type: IPC- IP Camera
DVR- recorder
Protocoll:
NETIP (for Identivision camera)
ONVIF
Stream:
Main stream (Default, good quality stream)
Extra stream (bad quality CIF resolution)
IP channel: Channel select for the camera
Address:
IP address
Port:
default: 34567
User name:
default: admin
Step 5.
Click on the Ok button, and if the camera settings are good, the camera’s picture will be on
the screen.
13. LAN CONNECTION
Step 1.
Step 2.
Step 3.
Install the ActiveX_V1.1.0.68 and QuickTimeInstaller software from the CD.
Open a web browser (Chrome, Internet Explorer, Firefox,...)
Write to the address bar, the IP address of the device.
91. picture
Login screen
Step 4.
Write the admin and user name. (default: user name:admin, password: (none))
Step 5.
Double click on the name of the camera. (if Internet Explorer ask to enable and run the
plugins, click to OK.)
67
92. picture
Camera screen
If Chrome is your default browser, you can enable the Quicktime Player to ask nothing while running.
First write the chrome://plugins/ address to browser, and next to the Quicktime PLayer name click ont he
Allways enable option.
93. picture
Chrome plugin settings
14. CLOUD CONNECTION\REMOTE ACCESS
14.1 Cloud connection\Remote Access
The devices can be used to remote access without any DynDNS provider.
Step 1.
On the device enable the Cloud option in the Netservice- Cloud settings.
Step 2.
Write to the browser the http://www.xmeye.net/ address.
68
94. picture
Step 3.
Step 4.
Step 5.
Remotea access
Click on the Enter Guide and with the easy wizard search the devices.
If the device has found, click on the next option (every option is automatic)
After the succces settings, the device will be shown on the left side.
95. picture
Remote access
14.2 Remote access (without wizard)
Step 1.
Step 2.
Click on the By Device option and write the factory number of the device (which will be
accessed)(it can be found in the Settings-Info-Version.
Step 3.
Click on the Login.
After the succces settings, the device will be shown on the left side.
Step 4.
14.3 Remote access (with more devices)
With these steps is it possible to make a profile, to access more devices.
Step 1.
Step 2.
Click on the Register option and write the optional settings ont he screen. Choose the OK
option.
Step 3.
If the Registration process is finished, check your email and click on the e-mail from the
xmeye and activate the profile.
Step 4.
On the new screen click on the Device Mananeg option and choose the Add.
69
96. picture
Step 5.
Device manager
Write the factory number, device name, password of the device. Click on the OK button.
97. picture
My devices menu
If the settings are OK, on the My devices screen the device will be shown.
15. MOBILPHONE\TABLET ACCESS WITH VMEYE APP
The Vmeye app can be used to watch the surveillance system, control the PTZ cameras.
Available mobilphone’s systems: Android, Blackberry, Iphone, Symbian, Windows mobile.
Step 1.
Install the right app for the mobilphone\tablet from the App store.
Step 2.
Click on the Settings option.
98. picture
Step 3.
Using the Vmeye app
Click on the ’Plus’ button to add a device and write the network settings to the fields.
70
99. picture
VMEye settings (example)
[DeviceName] Device name
[Address] IP address of the device
[Mobile Port] default: 34599
[User Name] default: admin
[Password] default: none
[Max channel] channel number of the device
Step 4.
Click on the OK button and the device can be access with the mobilphone.
100. picture Recorder access
71
16. CLOUD ACCESS WITH VMEYECLOUD APP
The devices can be used to remote access without any DynDNS provider with the VMeyecloud app.
Available mobilphone’s systems: Android, Blackberry, Iphone, Symbian, Windows mobile.
In
Step 1.
Install the right app for the mobilphone\tablet from the App store. (VMeyecloud)
Step 2.
If the devices was registered at the Xmeye.net page, with the user name and password can
be acccessed automatically.
Step 3.
If the device was not registered at the Xmeye.net page, click on the By Device option and
choose the Search option.
Step 4.
When the search finished and the device was found, click on it and choose ’plus’ button.
101. picture VMEyeCloud app
Step 5.
On the next page, you can change the settings of the device if it is necessary, otherwise click
on the OK button.
Step 6.
Close the settings menu and ont he main screen the picture of the device will be shown.
102. picture Finish
Note: There could be error messages with using the app, because the servers for this feature are in
China, but there are just temporary. This feature has 4-5 seconds delay!
72
17. SPECIFICATIONS
IIP-N411SP
MEGASTORE
IIP-N411SPOE
MEGASTORE
Record mode:
NVR
NVR
NVR
NVR
NVR
Analog mode:
-
-
-
-
-
FPS (analog)
-
-
-
-
-
Analog channels
-
-
-
-
-
HD-SDI channels (DVR mode):
Analog
+
Ip
channels
(HVR mode)
-
-
-
-
-
-
-
-
-
-
- 4*2MP.
- 4*1.3MP.
- 4*1.3MP.
- 8*2MP.
- 8*2MP.
25fps / ch
25fps / ch
25fps / ch
25fps / ch
25fps / ch
IDENTIVISION,
GEOVISION
IDENTIVISION,
GEOVISION
IDENTIVISION,
GEOVISION
IDENTIVISION, GEOVISION
IDENTIVISION, GEOVISION
LAN:
yes
yes
yes
yes
yes
WIFI:
with optional access
point
point
with optional
access point
with optional access point
with optional access point
with optional mobil
router
yes
with optional mobil
router
yes
with optional mobil
router
yes
with optional mobil router
with optional mobil router
yes
yes
CMS software
yes
yes
yes
yes
yes
Mobiltelephone client:
yes
yes
yes
yes
yes
with built in
microphone in the
cameras
0/0
with built in
microphone in the
cameras
0/0
with built in
microphone in the
cameras
0/0
-
-
with built in microphone in the
cameras
with built in microphone in the
cameras
0/0
0/0
16*12
16*12
16*12
16*12
16*12
yes
yes
yes
yes
yes
VGA video out:
1920*1080
1920*1080
1920*1080
1920*1080
1920*1080
HDMI video out:
1920*1080
1920*1080
1920*1080
1920*1080
1920*1080
BNC video out:
1
1
1
1
1
IP
(NVR mode)
Frame\s. (IP cameras):
Compatible cameras:
3G:
CLOUD:
Video analytics:
Audio record:
Alarm IN\OUT:
Video motion matrix
PTZ:
SPOT:
channels:
IIP-N810
MEGASTORE
IIP-N820
MEGASTORE
IIPIIP-N820SPOE
N810SPOE
MEGASTORE
MEGASTORE
IIP-N4120
MEGASTORE
-
-
-
-
-
Aspect Ratio:
16:9 / 4:3
16:9 / 4:3
16:9 / 4:3
16:9 / 4:3
16:9 / 4:3
HDD number:
1 x 4 TB
1 x 4 TB
1 x 4 TB
1 x 4 TB
2 x 4 TB
1 x 4 TB
3
2
RAID:
-
-
-
USB:
2
2
2
mouse,infra remote
mouse,infra remote
mouse,infra remote
mouse,infra remote
mouse,infra remote
-
yes (4 channels)
-
yes (4 channels)
yes (4 channels)
-
yes (4 channels)
yes (4 channels)
Manage:
Switch built-in:
POE built-in:
-
2 x 4 TB
2
3
73
IIP-N3210ECO
MEGASTORE
IIP-N1641
MEGASTORE
IIP-N2480
MEGASTORE
Record mode:
NVR
NVR
NVR
Analog mode:
-
-
-
FPS (analog)
-
-
-
Analog channels
-
-
-
HD-SDI channels (DVR mode):
Analog
+
Ip
channels
(HVR mode)
-
-
-
-
-
- 8*5MP
- 16*3MP
- 24*2MP.
- 32*1MP
25fps / ch
- 8*5MP
- 16*3MP
- 24*2MP.
- 32*1MP
25fps / ch
25fps / ch
IDENTIVISION,
GEOVISION
IDENTIVISION,
GEOVISION
IDENTIVISION,
GEOVISION
LAN:
yes
yes
yes
WIFI:
with optional
access point
point
point
with optional mobil
router
yes
with optional mobil
router
yes
with optional mobil
router
yes
CMS software
yes
yes
yes
Mobiltelephone client:
yes
yes
yes
with built in
microphone in the
cameras
0/0
with built in
microphone in the
cameras
16/4
with built in
microphone in the
cameras
16/4
16*12
16*12
16*12
yes
yes
yes
VGA video out:
1920*1080
1920*1080
1920*1080
HDMI video out:
1920*1080
1920*1080
1920*1080
BNC video out:
1
2
2
SPOT:
-
-
-
Aspect Ratio:
16:9 / 4:3
16:9 / 4:3
16:9 / 4:3
HDD number:
8 x 4 TB
IP
(NVR mode)
Frame\s. (IP cameras):
Compatible cameras:
3G:
CLOUD:
Video analytics:
Audio record:
Alarm IN\OUT:
Video motion matrix
PTZ:
channels:
- 24*2MP.
1 x 4 TB
4 x 4 TB
RAID:
-
-
-
USB:
3
2
2
mouse,infra remote
-
mouse,infra remote
-
mouse,infra remote
-
Manage:
Switch built-in:
POE built-in:
74
18. FAQ AND MAINTENANCE
If the problems are not listed, please contact the local service or call the HQ service. We are willing to offer
the service.
1. The DVR can not boot up normally.
Possible reasons are as followed:
 The power supply is not correct.

Switch power supply line is not in good connection.

Switch power supply is damaged.

The program updating is wrong.

The hard disk is damaged or the hard disk lines are broken.

The front panel is damaged.

The main board of the DVR is damaged.
2. The DVR reboots automatically or stops working after boot up a few minutes.
 The input voltage is not stable or too low.

The hard disk is damaged or the hard disk lines are broken.

The power of the switch power supply is low.

Frontal video signal is not stable.

Bad heat radiator or too much dust or bad running circumstance for the DVR.

The hardware of the DVR is damaged.
3. System can not detect hard disk.
 The hard disk power supply line is not connected.

The cables of the hard disk are damaged.

The hard disk is damaged.

The SATA port of main board is damaged.
4. There are no video outputs in single channel, multiple channels and all channels.
75
 The program is not matched. Please update the program.

The image brightness is all 0. Please restore the default setup.

There is no video input signal or the signal is too weak.

The channel protection or the screen protection is set.
 The hardware of the DVR is damaged.
5. Real-time image problems such as the image color or the brightness distortion.
 When using the BNC output, the option between the N mode or PAL mode is wrong and the image
becomes black and white.

The DVR is not matched the monitor impedance.

The video transmission distance is too far or the loss of the video transmission line is too large.

The color and brightness setting of the DVR is wrong.
6. I can not find the video files in local playback mode.
 The data line of the hard disk is damaged.


Update the different program with the origin program files.

The video files to look up are covered.

The recording is not on.
7. The local video is not clear.
 The image quality is too bad.

The reading program is wrong. Reboot up the DVR.

The data line of the hard disk is damaged.


8. There is no audio signal in the surveillance window.
76

It is not an active tone arm.

It is not an active sound box.

The audio lines are damaged.

9. There is audio signal in the surveillance window but mo audio signal in the playback state.
 Setting issues: the audio option is not chosen.

The according channel is not connected with the video.
10. The time is wrong.
 Setting is wrong..

The battery is in bad connection or the voltage is too low.

The oscillation is damaged.
11. The DVR can not control the PTZ.
 There is something wrong with the frontal PTZ.

The setting, connection or the installation of the PTZ decoder is not correct.

The connections are not correct.

The PTZ setting of the DVR is not correct.

The protocols of the PTZ decoder and the DVR are not matched.

The address of the PTZ decoder and the DVR are not matched.

When multiple decoders are connected, the far port of the PTZ decoder line A(B) must connect a
120 resistance to reduce the reflection otherwise the PTZ control is not stable. 

The distance is too far.
12. The motion detect is not working,
 The time range set is not correct.
 The motion detect area set is not correct.
 The sensitivity is too low.
 Limited by some hardware edition.
13. I can not login via web or CMS.
 The system is windows 98 or win me. We recommend updating to windows 2000sp4 or higher
Version or installing the software for low edition.

ActiveX is hold back.
77

The version is not exceeded dx8.1. Update the display card driver.

Network connection failure.

Network setting issues.

Invalid password or user name.

The CMS is not matched the DVR program version.
14. The image is not clear or there is no image in network preview state or video file playback
state.
 Network is not stable.

The user machine is resource limited.

Choose the play-in-team mode in the network setup of DVR.

The region shelter or channel protection is set.

The user has no surveillance purview.

The real-time image of the hard disk recording machine itself is not clear.
15. Network connection is not stable.
 Network is not stable.

IP address is conflicted.

MAC address is conflicted.

The net card of the DVR is bad.
16. There is something wrong with the USB backup or writing a CD.
 The rewritable machine and the hard disk are shared the same data lines.
Page 66
78

The data is too much. Please stop recording and backup.

The data exceeds the backup storage.

The backup equipment is not compatible.

The backup equipment is damaged.
17. The keyboard can not control the DVR.
 The serial port of the DVR is not set correctly.

The address is not correct.

When multiple transformers are connected, the power supply is not large enough. Please give each
transformer individual power supply.

The distance is too far.
18. Alarm can not be recessional.
 The setting of the alarm is not correct.

The alarm output is turned on manually.

The input machine is damaged or the connections are not correct.

There are some problems for specific program edition, Please update the program.
19. Alarm is not working.
 The setting of the alarm is not correct.

The connection of the alarm is not correct.

The alarm input signal is not correct.

A alarm is connected with two loops synchronously.
20. The remote controller is not working,
 The remote control address is not correct.

The remote control distance is too far or the angle is too large.

The battery is used up.

The remote controller or the front panel of the recording machine is damaged.
21. The storage time is not enough.
79
 Front vidicon quality is bad. The lens is too dirty. The vidicon is in backlighting installation.

The hard disk capability is not enough.

22. The downloading files can not play.
 There is no media player.

There is no DX8.1 software or higher edition.

There is no DivX503Bundle.exe file to play AVI video files.

DivX503Bundle.exe and ffdshow-2004 1012 .exe files must be installed in the windows xp system.
23. I can not remember the advanced code or network code in the local menu operation.
Please contact the local service or call the HQ service. We will offer the service according the machine type
and the program edition.
18.1 Maintenance
1. Please brush printed circuit boards, connectors, fans, machine box and so on regularly.
2. Please keep the grounding well done to prevent the video or audio signal interfered and the DVR
from static or inductive electricity.
3. Do not pull out the video signal line or RS-232 port or RS-485 port with the power on.
4. Do not use the TV in the local video output port(VOUT) of DVR. It will damage the video output
circuit easily.
5. Do not turn off the switch directly. Please use the turn-off function in the menu or press the turn-off
button in the panel (3 seconds or longer) to protect the hard disk.
6. Please keep the DVR away from heat resource.
7. Please keep the DVR ventilated for better heat radiator.
Please check the system and maintain regularly.
80

IDENTIVISION IIP- IP NVR recorders Installation Guide

Transcription

Similar documents

IDENTIVISION IIP- IP NVR recorders Manual Guide

Regions CD Check Viewer Installation Guide

Dome PoE H.264 - Atlantis-Land

Hotmail/Live/ MSN/Outlook.com

Time Sheet Reminder

Burglar Alarm Permit Form - Palm Beach County Sheriff`s Office

welcome to bell expressvu

Blaze Rush – Medium VR intensity - Targem

parents! - First In Math

S5100/ S5500 - Fujifilm USA

NVR - Ness Corporation

Burnout Legends - Sony PSP - Manual

SunEyes Mini NVR