M60 LED Recessed [L6Rx] selux.us

Transcription

M60 LED Recessed [L6Rx] selux.us
Customer:
Date:
Project:
Qty:
Type:
M60
LED Recessed
-
Order Code:
-
-
-
Series
L60
L6R1
Light Engine
1A351
1A301,2
Multi-Mount
Form
628lm/8.4W
per foot
-
-
1A251,2
464lm/6.0W
per foot
Available starting at 2’ and up.
2
MI
Clear Lens with
Microprism
Mounting
L60
SF1
SF2
SF3
SG
DC
Mounting
L6R1 or
L6R2
TB3
TBS3
PMT3
RC 4
TS
Nominal
Fixture
Length
01*
Finish
WH
Voltage
40
3500K
4000K
Spackle Flange Spackle Flange Spackle Flange Slot Grid (9/16”) Decoustic
(1/2” Drywall) (5/8” Drywall) (After Drywall) (Wire Suspension Ceiling
or 1/4-20 stud)
(up to 2” thick)
T-Bar Length w/ T-Bar Length
suspension clips w/1” 1/4-20
Stud
1 ft.
025
2 ft.
03
3 ft.
04 5
4 ft.
T-Bar Length
Perimeter
Mount
055
5 ft.
Rotating
1” 1/4-20 Stud
Crossbar
(Ceilings 1/4” to
2” thick )
06 5 07
6 ft.
7 ft.
PM
3
Perimeter
Mount
Consult factory for lengths under 2’
085 XX
8 ft.
L6R1 only
4
Length intended to fit centered between the
grid for SG, TB, TBS, PMT mountings.
5
Runs (over 8’) & Configurations, round up to the nearest
foot and replace the “xx” with the # (i.e. 09=09’ nominal)
*1’ fixture only available with 1A35 light engine.
Individual fixtures, Runs and Configurations are supplied in nominal lengths to ensure full, even,
illumination. See pages 2 thru 6 for additional details.
BK
SV
120
277
UNV
120 Volt
277 Volt
120 thru 277
50/60hz capable
DIM6
DM6,7
DML6,7
White
Fixture
Options
DL10
Sensor
Options
xE12,13
Damp Location
Rated
Enlighted
Black
Silver
EC
15
Emergency
Circuit Wiring
Configuration IL9018
Lit Horizontal
Options
90° Corner
SP
FS10
In-line Fuse
xP112,13
Philips Daylight
SS10
Separate
Switching
xP212,13
Philips Occ/
Vac
EMN
Custom colors are available, Please consult factory
Specify Premium Color
DMD6,7
eldoLED DALI
eldoLED
eldoLED
SOLOdrive 0-10V SOLOdrive 0-10V (Logarithmic)
(Linear)
(Logarithmic)
Replace “x” with quantity
YEAR
-
Values calculated from a 4’ fixture @4000K
using LW Shielding and DM driver.
For additional information please see page 2.
LED Optimized
white lens
0-10V
(Linear)
5
-
1 376lm/4.9W
per foot
LW
Emergency
Options
-
1A201,2
Shielding
Driver
35
3000K
-
Continuous Flange
(Flangeless Endcaps)
30
2700K
-
L6R2
Continuous Flange
(Flanged Endcaps)
552lm/7.2W
per foot
-
27
CCT
LED WARRANTY
-
CCEA10
CCEA
approved
xP312,13
Philips
Occ/Vac/Daylight
DC26,7,8
Lutron 2-Wire
DC36,7
Lutron 3-Wire
DCE6,7
Lutron EcoSystem
SR6,7,9
Philips
Xitanium SR
DALI
C911
Sensor Switch
Daylight
For use with E and P sensors only
9
See page 8 for full details and restrictions
Not available with EMN option
xS212,14
Sensor Switch
Occ/Vac
xS312,14
Sensor Switch
Occ/Vac/Daylight
Minimum fixture length 2’. See page 9 for
full details and restrictions
12
For use with SR driver only
13
For use with DIM driver only
14
See page 8 for full details and restrictions
15
EM battery pack
(Non-IC-rated)
Lit Inverted
90° Corner
120V only
8
11
16,17
V9018
Not available for 1’ length
7
10
90 CRI
xS112,14
See page 7 for full details
6
120 or 277 Volt only
16
Not available on lengths under 4’
17
IT9018
Lit “T” section
IX9016
See pages 10 and 11 for full details and restrictions
18
Lit “X” section
ARRA
Compliant
Selux Corporation © 2016, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 1 of 13
(Rev. 10/2016)
L60_Rec_ss_v2.5
M60
LED Recessed
2 3/8”
(60mm)
3 9/16”
3 9/16”
(91mm)
2 1/4”
(56mm)
2 3/8”
(60mm)
(91mm)
2 1/4”
(56mm)
3 5/16”
(84mm)
LW lens shown for reference
Construction:
Electrical/Performance:
Housing - Continuous, low copper 6063-T6
extruded aluminum profile with aluminum
endcaps, available as Individual fixtures (up to
12’) or Runs.
LED Light Engine - Brand-name mid-power
LEDs create a high efficiency LED light engine
able to provide a lumen maintenance of 96%
at 25,000 hours and 93% at 60,000 hours per
TM-21 report.
Flange - 9/16” (14mm) wide flange runs full
lengths of both sides and is part of the main
extruded body. Specify continuous flange (L6R1)
or flush (L6R2) end cap. L6R2 does not work in
T-Bar ceiling.
Geartray - Low copper 6063-T6 extruded aluminum profile.
Shielding - Extruded, impact resistant acrylic
snap in lens:
- LED optimized white lens (LW)
- Clear lens with microprism (MI)
Mounting(s) - Spackle in (drywall), Slot grid,
Decoustic, T-bar grid, Perimeter, Rotating
Crossbar and Threaded Stud Mountings (see
pages 3 thru 6 for details).
Standard Luminaire lengths - All standard
luminaires are supplied in nominal lengths to
ensure full, even, illumination. Runs and Configurations are available in approximately 1/4”
increments starting at the nominal 8’ fixture
length.
** Individual luminaires are not joinable in the
field.
Exact length luminaires - Individual luminaires, runs, and configuration are available
in exact lengths to meet your project needs.
Please consult factory with you requirements.
** Lens luminance may soften at the very
ends of the straight sections for exact length
luminaires.
L60 Joiner(s) - Runs and configurations are
supplied in multiple housing that are joined
together in the field using the supplied L60
Joiner System. This allows ease of installation
and ensures a uniform appearance (see page 8
for detail).
LED Life - Calculated L70 greater than 398,000
hours and Reported L70 greater than 60,000
hours @ 25°C per TM-21
Delivered Lumens - Due to LED manufacturer’s
tolerances the listed output has a ±5% tolerance. For outputs based on different shielding
or CCT please see photometry section at the
end.
CCT - Available in 2700K, 3000K, 3500K and
4000K, tolerance within a 3-step MacAdam
ellipse.
CRI - Min. 80. Optional 90CRI - for 2700K &
4000K, consult factory.
All Drivers - High efficiency, constant current,
soft start, Electronic Class 2 with a PFC>0.90.
For more detailed information on the available
drivers please see page 7.
Sensors - Selux offers a variety of integral
sensor options. For details and specifications,
please refer to page 9.
Thermal Performance:
Ambient Operating Temperature - Luminaires
suitable for Max. ambient temperature of
35° C (95° F) for all drivers.
Min. ambient temperature of:
-20°C (-4°F) for DIM, DM, DML, DMD,and SR
drivers.
0°C (32°F) for the DC2, DC3 and DCE drivers.
Luminaire Finish:
Powder Coat - All Selux luminaries are finished
in high quality polyester powder coating in our
Tiger Drylac certified facility and are tested in
accordance with test specifications for coatings
from ASTM and PCI.
All products undergo a five stage intensive
pretreatment process where product is thoroughly cleaned, phosphated, and sealed. Selux
powder coated products provide excellent salt
and humidity resistance as well as ultra violet
resistance for color retention.
Standard interior colors are White (WH), Black
(BK), and Silver (SV). Selux premium colors (SP)
are available, please specify from your Selux
color selection guide.
Warranty:
5 Year Limited LED Luminaire Warranty Selux offers a 5 Year Limited Warranty to the
original purchaser that the M60 series LED luminaire shall be free from defects in material and
workmanship for up to five (5) years from date
of shipment. This limited warranty covers the
LED driver and LED light engine when installed
according to Selux instructions and operated
within the Ambient Temperature. For additional
details and exclusions, see “Selux Terms and
Condition of Sale.”
Certifications and Compliance:
NRTL - For Dry and Damp location
(I.E. cULus; cCSAus)
ARRA Compliant
RoHS Compliant
IC-Rated *
*EMN option is Non-IC-rated
Selux Corporation © 2016, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 2 of 13
(Rev. 10/2016)
L60_Rec_ss_v2.5
M60
LED Recessed
1/2” Spackle Flange Mounting (SF1)
1/2” Spackle Flange Mounting (SF1)
5/8” Spackle Flange Mounting (SF2)
5/8” Spackle Flange Mounting (SF2)
After Sheetrock Flange Mounting (SF3)
After Sheetrock Flange Mounting (SF3)
After drywall
installation
Spackle Flange Mounting (SF1, SF2 & SF3) - Dimensions
Nominal
Length
“A”
O.A.L. w/o Flange
“B”
End Suspensions
* “C” (Ref.)
Mid. Suspension
“D”
Feed Location
Feet/Inch
MM
Feet/Inch
MM
Feet/Inch
MM
Feet/Inch
MM
01 (1 ft.)
1' - 5/16"
313
0' - 1 5/8"
41
0' - 9 1/8"
231
0' - 4 1/8"
105
02 (2 ft.)
1' - 11 7/16"
595
0' - 1 5/8"
41
1' - 8 3/16"
513
0' - 4 1/8"
105
03 (3 ft.)
3' - 5/16"
923
0' - 6 1/8"
156
2' - 1/8"
612
0' - 2 1/8"
54
04 (4 ft.)
3' - 11 7/16"
1205
0' - 6 1/8"
156
2' - 11 3/16"
894
0' - 2 1/8"
54
05 (5 ft.)
4' - 11 7/16"
1510
0' - 6 1/8"
156
3' - 11 3/16"
1199
0' - 2 1/8"
54
06 (6 ft.)
5' - 11 7/16"
1815
0' - 6 1/8"
156
4' - 11 3/16"
1504
0' - 2 1/8"
54
07 (7 ft.)
6' - 11 7/16"
2119
0' - 6 1/8"
156
5' - 11 3/16"
1808
0' - 2 1/8"
54
08 (8 ft.)
7' - 11 7/16"
2424
0' - 6 1/8"
156
6' - 11 3/16"
2113
0' - 2 1/8"
54
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
1. 1/4-20 Threaded rod to struture (supplied and installed by others).
2. 14-20 Coupler hardware (supplied and installed by others).
3. 1” 1/4-20 Stud (by Selux).
4. Ø5/16” [Ø7mm] mounting hole.
5. Drywall/Sheetrock screw (Ref.)
6. Drywall/Sheetrock (Ref.)
7. 1/6” Plaster skimcoat (Ref.)
8. Drywall/Sheetrock tape (Ref.)
9. Blocking to secure fixture (by others)
10. Electrical connection box, removable side cover for electrical
connection pre-installation, once installed the wiring is accessible from below the ceiling through the luminaire.
11. Luminaires ship with the brackets pre-installed.
- The brackets cannot be removed until the fixture is completely
installed and secured through the spackle flange.
- Once the brackets are removed, the lens/louvers can be
installed.
Selux Corporation © 2016, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 3 of 13
(Rev. 10/2016)
L60_Rec_ss_v2.5
M60
LED Recessed
Slot Grid Mounting (SG)
9/16” Slot Grid Mounting (SG)
(Wire Suspension or 1/4-20 Stud)
1. 9/16” Slot grid (shown as ref.)
2. Support wire to structure
(supplied and installed by others).
3. 1/4-20 Threaded rod to structure
(supplied and installed by others).
4. 1/4-20 Coupler hardware
(supplied and installed by others).
5. 1” 1/4-20 Stud (by Selux).
6. Ø5/16” [Ø7mm] mounting hole.
Slot Grid Mounting (SG) - Dimensions
Nominal
Length
“A”
Housing Length
Feet/Inch
MM
“B”
End Suspensions
Feet/Inch
* “C” (Ref.)
Mid. Suspension
MM
Feet/Inch
“D”
Feed Location
“E”
Grid Spacing
MM
Feet/Inch
MM
Feet
02 (2 ft.)
1' - 11 7/16"
595
0' - 1 5/8"
41
1' - 8 3/16"
513
0' - 4 1/8"
105
2’ Center to Center
04 (4 ft.)
3' - 11 7/16"
1205
0' - 6 1/8"
156
2' - 11 3/16"
894
0' - 2 1/8"
54
4’ Center to Center
05 (5 ft.)
4' - 11 7/16"
1510
0' - 6 1/8"
156
3' - 11 3/16"
1199
0' - 2 1/8"
54
5’ Center to Center
06 (6 ft.)
5' - 11 7/16"
1815
0' - 6 1/8"
156
4' - 11 3/16"
1504
0' - 2 1/8"
54
6’ Center to Center
08 (8 ft.)
7' - 11 7/16"
2424
0' - 6 1/8"
156
6' - 11 3/16"
2113
0' - 2 1/8"
54
8’ Center to Center
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
Decoustic Mounting (DC)
Decoustic Mounting (DC)
(Panels up to 2” thick)
Decoustic Mounting (DC) - Dimensions
Nominal
Length
“A”
Housing Length
“B”
End Suspensions
* “C” (Ref.)
Mid. Suspension
“D”
Feed Location
Feet/Inch
MM
Feet/Inch
MM
Feet/Inch
MM
Feet/Inch
01 (1 ft.)
1' - 5/16"
313
0' - 1 5/8"
41
0' - 9 1/8"
231
0' - 4 1/8"
MM
105
02 (2 ft.)
1' - 11 7/16"
595
0' - 1 5/8"
41
1' - 8 3/16"
513
0' - 4 1/8"
105
03 (3 ft.)
3' - 5/16"
923
0' - 6 1/8"
156
2' - 1/8"
612
0' - 2 1/8"
54
04 (4 ft.)
3' - 11 7/16"
1205
0' - 6 1/8"
156
2' - 11 3/16"
894
0' - 2 1/8"
54
05 (5 ft.)
4' - 11 7/16"
1510
0' - 6 1/8"
156
3' - 11 3/16"
1199
0' - 2 1/8"
54
06 (6 ft.)
5' - 11 7/16"
1815
0' - 6 1/8"
156
4' - 11 3/16"
1504
0' - 2 1/8"
54
07 (7 ft.)
6' - 11 7/16"
2119
0' - 6 1/8"
156
5' - 11 3/16"
1808
0' - 2 1/8"
54
08 (8 ft.)
7' - 11 7/16"
2424
0' - 6 1/8"
156
6' - 11 3/16"
2113
0' - 2 1/8"
54
1. 1/4-20 Threaded rod to structure (supplied and installed by others).
2. 1/4-20 Coupler hardware (supplied and installed by others).
3. 1 ” 1/4-20 Stud (by Selux).
4. Ø5/16” [Ø7mm] mounting hole.
5. 1/2” wide alum. angle runs the entire length of fixture to block view into
plenum area from below fixture.
6. Suitable for Decoustic® ceiling panel installations with panels up to 2” thick
(supplied and installed by others). Other ceiling systems possible, please
consult factory. Decoustic® is a registered trademark of Decoustics Ltd.
Corporation.
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
Selux Corporation © 2016, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 4 of 13
(Rev. 10/2016)
L60_Rec_ss_v2.5
M60
LED Recessed
T-Bar Mounting (TB)
T-Bar with Stud Mounting (TBS)
T-Bar with Suspension Clips (TB)
T-Bar with 1/4-20 Stud (TBS)
(9/16” or 15/16” grid)
(9/16” or 15/16” grid)
1. Support wire to structure (supplied and installed by others).
2. Spring steel suspension clips located approximately every 4 ft.
(supplied by Selux).
3. 9/16” T-bar grid (shown as ref.)
3a. 15/16” T-bar grid (shown as ref.)
4. 1/4-20 Threaded rod to structure (supplied and installed by others).
5. 1/4-20 Coupler hardware (supplied and installed by others).
6. 1” 1/4-20 Stud (by Selux).
7. Ø5/16” [Ø7mm] mounting hole.
T-Bar (TB & TBS) and Perimeter Mount (PMT) - Dimensions
Nominal
Length
“A”
O.A.L. with Flange
Feet/Inch
MM
“A1”
O.A.L. without Flange
Feet/Inch
MM
“B”
End Suspensions
Feet/Inch
MM
“BB” (TB mtg.)
Suspension
Clips
Quantity
** “C” (Ref.)
Mid. Suspension
Feet/Inch
MM
“D”
Feed Location
Feet/Inch
“E”
Grid Spacing
MM
Feet
“F”
Wall Angle
Feet/Inch
MM
*02 (2 ft.)
1' - 11 13/16"
605
1' - 10 15/16"
583
0' - 4 1/8"
114
4x
1' - 2"
355
0' - 1 1/8"
28
2’ Center to Center
1' - 11 13/16"
605
*04 (4 ft.)
3' - 11 13/16"
1215
3' - 10 15/16"
1193
0' - 6 1/8"
156
6x
2' - 10 11/16"
882
0' - 2 1/8"
54
4’ Center to Center
3' - 11 13/16"
1215
*05 (5 ft.)
4' - 11 13/16"
1519
4' - 10 15/16"
1497
0' - 6 1/8"
156
6x
3' - 10 11/16"
1187
0' - 2 1/8"
54
5’ Center to Center
4' - 11 13/16"
1519
*06 (6 ft.)
5' - 11 7/8"
1825
5' - 11"
1803
0' - 6 1/8"
156
6x
4' - 10 3/4"
1492
0' - 2 1/8"
54
6’ Center to Center
5' - 11 7/8"
1825
*08 (8 ft.)
7' - 11 13/16"
2434
7' - 10 15/16"
2412
0' - 6 1/8"
156
8x
6' - 10 11/16"
2101
0' - 2 1/8"
54
8’ Center to Center
7' - 11 13/16"
2434
**Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
*For other lengths consult factory
Perimeter Mounting T-Bar Length (PMT)
Perimeter Mount T-Bar Length (PMT)
(Recessed Wall Mounting)
8. S
teel Wall Bracket with provision for 1/4-20 fasteners
(hardware to code by others).
9. 2” 1/4-20 Stud (by Selux).
10. 1/2” x 1” Alum. wall angle allows a gap between flange
and wall to create shadow line allowing for uneveness
of wall. Provision for #10 screws supplied approximately
every 2 ft. (hardware to code by others).
Selux Corporation © 2016, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 5 of 13
(Rev. 10/2016)
L60_Rec_ss_v2.5
M60
LED Recessed
Rotating Crossbar Mounting (RC)
1/4-20 Threaded Stud Mounting (TS)
Rotating Crossbars (RC)
1/4-20 Threaded Stud (TS)
(1/4” to 2” thick ceiling)
(1” Threaded Stud)
1. Rotating Crossbar intended for inaccessible ceilings, adjustable for ceiling
thickness of 1/4” to 2”.
2. 1/4-20 Threaded rod to structure (supplied and installed by others).
3. 1/4-20 Coupler hardware (supplied and installed by others).
4. 1” 1/4-20 Stud (by Selux).
5. Ø5/16” [Ø7mm] mounting hole.
Rotating Crossbar (RC), Threaded Stud (TS), and Perimeter Mountings (PM) - Dimensions
Nominal
Length
“A”
O.A.L. with Flange
“A1”
O.A.L. without Flange
“B”
End Suspensions
** “C” (Ref.)
Mid. Suspension
“D”
Feed Location
“E”
Wall Angle
Feet/Inch
MM
Feet/Inch
MM
Feet/Inch
MM
Feet/Inch
MM
Feet/Inch
MM
Feet/Inch
MM
*01 (1 ft.)
1' - 1 3/16"
335
1' - 5/16"
313
0' - 1 5/8"
41
0' - 9 1/8"
231
0' - 4 1/8"
105
1' - 1 3/16"
335
605
02 (2 ft.)
1' - 11 13/16"
605
1' - 10 15/16"
583
0' - 4 1/2"
114
1' - 2"
355
0' - 1 1/8"
28
1' - 11 13/16"
03 (3 ft.)
3' - 1 3/16"
945
3' - 5/16"
923
0' - 6 1/8"
156
2' - 1/8"
612
0' - 2 1/8"
54
3' - 1 3/16"
945
04 (4 ft.)
3' - 11 13/16"
1215
3' - 10 15/16"
1193
0' - 6 1/8"
156
2' - 10 11/16"
882
0' - 2 1/8"
54
3' - 11 13/16"
1215
05 (5 ft.)
4' - 11 13/16"
1519
4' - 10 15/16"
1497
0' - 6 1/8"
156
3' - 10 11/16"
1187
0' - 2 1/8"
54
4' - 11 13/16"
1519
06 (6 ft.)
5' - 11 7/8"
1825
5' - 11"
1803
0' - 6 1/8"
156
4' - 10 3/4"
1492
0' - 2 1/8"
54
5' - 11 7/8"
1825
07 (7 ft.)
6' - 11 13/16"
2129
6' - 10 15/16"
2107
0' - 6 1/8"
156
5' - 10 11/16"
1796
0' - 2 1/8"
54
6' - 11 13/16"
2129
08 (8 ft.)
7' - 11 13/16"
2434
7' - 10 15/16"
2412
0' - 6 1/8"
156
6' - 10 11/16"
2101
0' - 2 1/8"
54
7' - 11 13/16"
2434
*RC mounting, consult factory for lengths under 2’
Perimeter Mounting (PM)
**Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
Perimeter Mount (PM)
(Recessed Wall Mounting)
6. Steel Wall Bracket with provision for 1/4-20 fasteners (hardware to code by others).
7. 2” 1/4-20 Stud (by Selux).
8. 1/2” x 1” Alum. wall angle allows a gap between flange and
wall to create shadow line allowing for uneveness of wall.
Provision for #10 screws supplied approximately every 2 ft.
(hardware to code by others).
Selux Corporation © 2016, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 6 of 13
(Rev. 10/2016)
L60_Rec_ss_v2.5
M60
LED Recessed
Drivers:
0-10V linear dimming (DIM)
Luminaires supplied with drivers offering the capability of either normal
switched operation of 0-10V dimming for linear dimming curve. Fixtures
ship wired for dimming. For on/off functionality, simply cap the dimming
leads. Minimum dimming level preset at factory to 1%. (Due to size constraints, 1’ luminaires are supplied with a driver from a different manufacturer than 2’ and above luminaires. For details, please consult factory).
eldoLED SOLOdrive 0-10V linear dimming (DM)
Luminaires supplied with SOLOdrive 0-10V dimming driver for linear dimming curve. Minimum dimming level preset at factory to 1%. For “dim to
dark” (down to 0.1%), please consult factory.
eldoLED SOLOdrive 0-10V logarithmic dimming (DML)
Luminaires supplied with SOLOdrive 0-10V dimming driver for logarithmic
dimming curve. Minimum dimming level preset at factory to 1%. For “dim
to dark” (down to 0.1%), please consult factory.
eldoLED SOLOdrive DALI dimming (DMD)
Luminaires supplied with SOLOdrive DALI dimming driver for logarithmic
dimming curve. Minimum dimming level preset at factory to 1%. For “dim
to dark” (down to 0.1%), please consult factory.
LUTRON 2-wire dimming (DC2)
Luminaires supplied with A-series 2-wire dimming driver programmed for
Constant Current Reduction (CCR). For Pulse Width Modulation (PWM)
dimming, please consult factory. Minimum dimming level down to 1%.
LUTRON 3-wire dimming (DC3)
Luminaires supplied with A-series 3-wire dimming driver programmed for
Constant Current Reduction (CCR). For Pulse Width Modulation (PWM)
dimming, please consult factory. Minimum dimming level down to 1%.
LUTRON Ecosystem dimming (DCE)
Luminaires supplied with A-series EcoSystem (4 wire, digital link) dimming driver programmed for Constant Current Reduction (CCR). For Pulse
Width Modulation (PWM) dimming, please consult factory. Minimum
dimming level down to 1%.
* For control recommendations and system layout for Lutron drivers,
please contact Lutron.
Philips Xitanium Sensor Ready DALI dimming (SR)
Luminaires supplied with Xitanium SR dimming driver programmed for
Constant Current Reduction (CCR). Minimum dimming level down to 5%.
For use with E and P sensors only.
* For control recommendations for eldoLED drivers, please consult
eldoLED.
Driver Quantity
DIM, DM, DML, DMD, and SR
drivers
DC2, DC3, & DCE drivers
1 ft.
2 ft.
3 ft.
4 ft.
5 ft.
6 ft.
7 ft.
8 ft.
9 ft.
10 ft.
11 ft.
12 ft.
RUN
1
1
1
1
1
1
2
2
2
2
3
3
Approximately 1 driver
per 4 ft.
N/A
1
1
1
2
2
2
2
3
3
3
3
Consult Factory
*For inrush and control current, please refer to the driver manufacturers’ spec sheets.
Wiring Diagrams
0-10V linear (DIM)
0-10V linear eldoLED SOLOdrive (DM)
0-10V logarithmic eldoLED SOLOdrive (DML)
DALI eldoLED SOLOdrive (DMD)
Philips SR DALI (SR)
Sensor Wiring Diagrams
standard
DIM, DM,
DML, DMD & SR
DALI
DALI
ENLIGHTED
OR PHILIPS
SENSOR
SR (+)
SR (-)
PHILIPS XR
SENSOR
SWITCH
ELDO 0-10V
(+)
(-)
Selux Corporation © 2016, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
0-10V
AUX (+)
AUX (-)
Page 7 of 13
(Rev. 10/2016)
L60_Rec_ss_v2.5
M60
LED Recessed
Fuse (FS) - Fusing, luminaires supplied with a in-line fuse located on the
hot wire for each feed. (supplied with an 8A slow burn fuse).
Damp Location (DL) - Luminaires are suitable for use in damp
location(s). Examples of such locations include protected areas under
canopies, marquees, roofed porches, and similar locations where the
fixture(s) are protected from direct contact with rain, snow, or excessive
moisture (such as ocean spray). Interior locations include areas subject
to moderate degrees of moisture, such as basements and certain barns
and cold storage buildings. All solder points on LED boards are conformal
coated. The phosphor layer of the LEDs is free of coating to avoid hazing.
Separate Switching (SS) - Luminaires available with separately
switched 4’ (nominal) sections starting at 7’ and up. Luminaire is intended to be wired to the same panel/breaker (not intended for Emergency use).
- To specify this option, the number of separately switched sections and
locations of these sections must be provided at time of order.
* If the project requires different separate switching than outlined above
please consult the factory.
*For Separate Switching with sensors, please consult factory.
*For Damp Location with sensors, please consult factory.
EMN (Emergency Battery Pack)* - Emergency battery pack is available starting at the 4’ nominal length and up in 2’ nominal sections. The
battery pack is housed in a box on the top of the luminaire and is fully
accessible from below the ceiling.
- F or individual luminaires, the lit section will be located on the feed end
of the fixture. If a different location is needed please consult the factory.
EMN Model #
Input
Operation Time
Lumen Output
CCT
Shielding
IOTA ILB-2412
2.5W Max.
90 Minutes
*836 lm
**4000K
LW
*Lumen output is fixed and the same for all light engines
**See page 12 for CCT multiplier
- For Runs, please specify location of lit section (in 2’ nominal sections).
*Luminaires with EMN option are Non-IC-rated
* For EMN with sensors, please consult factory.
1’-5”(432mm)
2 3/4”(70mm)
Emergency Circuit (EC) - Luminaires with EC option compliant to UL
924 listed emergency luminaire. EC luminaires are intended to be wired to
separate panels/breakers for emergency use.
- For 1’ to 6’ nominal luminaires, the entire fixture is wired for
operation on emergency circuit.
- For 7’ and up nominal luminaires, the first 4’ nominal length is
wired for operation by a separate EM circuit by default to meet
the required “Life Safety Code” (NFPA 101).
* If a different configuration is needed please consult the factory.
* For EC with sensors, please consult factory.
Flex Whip - standard for recessed fixtures
Joiner System - standard for Runs and Configurations
90° Elbow on top of the housing (7/8" feed hole)
3/8" flexible metal conduit (6' long)
6" leads
Straight fitting
Selux Corporation © 2016, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 8 of 13
(Rev. 10/2016)
L60_Rec_ss_v2.5
M60
LED Recessed
Sensor Ordering Chart
Quantity
x Number of Sensors
Sensor
Settings*
E Enlighted FS-D22
1 Daylight
P Philips Easy Sense SNS102
2 Occupancy/Vacancy
S Sensor Switch MSD EZ
3 Daylight/Occupancy/Vacancy
* Settings not available with Enlighted
Enlighted FS-D22 (E)
Occupancy/vacancy, daylight harvesting, plus the Internet of Things (IoT) data collection and reporting. For full details, please see FS-D22 spec sheet
on the Enlighted website. Must be paired with Philips Xitanium SR driver (SR driver selection). Commissioning by Enlighted. Please contact Enlighted
for complete details prior to specifying.
Philips EasySense SNS102 (P)
Occupancy/vacancy and daylight harvesting. Sensor can be programmed on-site via NFC or IR using Android app only, by others. For full details,
please see the SNS102 spec sheet on the Philips website. Must be paired with Philips Xitanium SR driver (SR driver selection). Wall dimming via wireless
wall switch from Philips/Illumra (www.illumra.com/easysense). Please contact Philips for complete details prior to specifying.
Sensor Switch MSD EZ (S)
Occupancy/vacancy and daylight harvesting. For full functionality and programming options, select settings option 3. If a different settings option is
selected, other settings may be unavailable. For full details, please see MSD EZ spec sheets on the Sensor Switch website. Must be paired with eldoLED
0-10V driver (DIM driver selection). Manual control of dimming not available with MSD EZ sensor. Please contact Sensor Switch for complete details
prior to specifying.
Occupancy
Enlighted FS-D22 (E)
Vacancy
Daylight Harvesting
See Enlighted’s website for full capabilities
Driver Compatibility
SR
Philips EasySense SNS102 (P)
√
√
√
SR
Sensor Switch MSD EZ (S)
√
√
√
DIM
Factory Presets - S
ensors come from the sensor manufacturer with factory presets for each of the settings in above chart. Please see sensor
manufacturers’ spec sheets for details on presets and re-programming.
Commissioning - Commissioning of sensors and installation by others. Contact sensor manufacturer for details and costs associated with
commissioning the system prior to specification of sensors.
Sensor Placement - for other placement options, please consult factory.
Qty 1 Sensor - Beginning
Qty 2 Sensor - Beginning and End
Fixture Length
Lit Section*
3”
(76mm)
2 3/8”
Qty 3+ Sensor - For spacing between sensors, please consult the sensor manufacturer.
(60mm)
Lens
Beginning of Run
Exact sensor placement will be defined by approved factory drawing.
Sensor Plate
*Lit section will be the fixture length minus 3”
for sensor plate.
Selux Corporation © 2016, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 9 of 13
(Rev. 10/2016)
L60_Rec_ss_v2.5
M60
LED Recessed
Standard Recessed (L60) shapes/configurations:
Listed below are the minimum lengths and details for standard shapes.
These standard shapes can be combined with each other and/or the
standard luminaire lengths, ensuring full even illumination. If you have any
questions, please consult the factory.
The minimum standard lengths for “L” shapes:
- IL90 or V90 open shapes is 4’ x 4’ nominal (example: leg, 90, leg)
- IL90 or V90 closed shapes is 6’ x 6’ nominal (example: 90, leg, 90)
(E xception is that the IL90 & V90’s can be joined directly to provide
a 4’ x 4’ nominal shape)
The minimum standard lengths for “T” & “X” shapes:
- IT90 = 4’ nominal on the short leg and 8’ nominal on the long side
- IX90 = 8’ nominal for either direction
*For sensors in configurations, please consult factory.
Project Specific Recessed (L60) shapes/configurations:
Selux is capable of supplying a wide range of project solutions including different shapes, angles, and sizes to meet the project requirements.
Due to the complex nature of these project specific layout(s) we ask that you please consult the factory with the project requirements for review.
Recessed (L60) Lit Corner and Section - Dimensions
IL90
V90
Feet/Inch
MM
“A” Housing (Outside)
2' - 1 1/4"
642
“A1” Housing (Inside)
1' - 10 15/16"
582
Feet/Inch
IT90
MM
“B” Housing (Outside)
1' - 11 1/2"
597
“B1” Housing (Inside)
2' - 3 1/16"
688
“C” Housing (Inside)
IX90
Feet/Inch
MM
2' - 1 1/4"
642
* “C1” Ref.
2' - 1/8"
612
“D” Housing
4' - 3/16"
1224
* “D1” Ref.
2' - 1/8"
612
“E” Housing
* “E1” Ref.
Feet/Inch
MM
4' - 3/16"
1224
2' - 1/8"
612
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
Selux Corporation © 2016, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 10 of 13
(Rev. 10/2016)
L60_Rec_ss_v2.5
M60
LED Recessed
Standard Recessed (L6R1/2) shapes/configurations:
Listed below are the minimum lengths and details for standard shapes.
These standard shapes can be combined with each other and/or the
standard luminaire lengths, ensuring full even illumination. If you have any
questions please consult the factory.
The minimum standard lengths for “T” & “X” shapes:
- IT90 = 4’ nominal on the short leg and 8’ nominal on the long side
- IX90 = 8’ nominal for either direction
The minimum standard lengths for “L” shapes:
- IL90 or V90 open shapes is 4’ x 4’ nominal (example, leg, 90, leg)
- IL90 or V90 closed shapes is 6’ x 6’ nominal (example, 90, leg, 90)
(E xception is that the IL90 & V90’s can be joined directly to provide
a 4’ x 4’ nominal shape)
*For sensors in configurations, please consult factory.
Project Specific Recessed (L6R1/2) shapes/configurations:
Selux is capable of supplying a wide range of project solutions including different shapes, angles, and sizes to meet the project requirements.
Due to the complex nature of these project specific layout(s) we ask that you please consult the factory with the project requirements for review.
Recessed (L6R1/R2) Lit Corner and Section - Dimensions
IL90
V90
Feet/Inch
MM
“A” w/Flange (Outside)
2' - 1 3/4"
654
“A1” Housing (Outside)
2' - 1 1/4"
642
IT90
Feet/Inch
MM
“C” Housing (Inside)
2' - 3 1/16"
688
“C1” Housing (Outside)
1' - 11 1/2"
597
IX90
Feet/Inch
MM
Feet/Inch
MM
“D” w/Flange
2' - 1 3/4"
654
“D1” Housing
2' - 1 1/4"
642
* “D2” Ref.
2' - 1/8"
612
“E” Housing
4' - 3/16"
1224
“F” Housing
* “E1” Ref.
2' - 1/8"
612
4' - 3/16"
1224
* “F1” Ref.
2' - 1/8"
612
“B” w/Flange (Inside)
1' - 10 7/16"
570
“B1” Housing (Inside)
1' - 10 15/16"
582
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
Selux Corporation © 2016, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 11 of 13
(Rev. 10/2016)
L60_Rec_ss_v2.5
M60
LED Recessed
Photometry
LW Optics / 34W LED / 4000K CCT
871
Link to photometry (IES & PDF files)
653
435
218
Catalog #: L60-1A35-40-LW-04-120
Report #: 747922
Delievered Lumens: 2511
Input Watts: 34W
Efficacy: 74
Power Factor: 0.994
Total Harmonic Distortion: 5.39
CCT: 3926K
CRI: 84.1
Max Candela: 871 @ 2.5° from Vertical
Spacing Criterion (0-180): 1.28
Spacing Criterion (90-270): 1.28
Spacing Criterion (Diagonal): 1.38
MI Optics / 35W LED / 4000K CCT
2
1
Maximum Candela = 870.7 Located At Horizontal Angle = 90, Vertical Angle = 2.5
# 1 - Vertical Plane Through Horizontal Angles (90 - 270)
# 2 - Vertical Plane Through Horizontal Angles (0 - 180)
1496
Link to photometry (IES & PDF files)
1122
748
374
Catalog #: L60-1A35-40-MI-04-120
Report #: 749917-L6040MI
Delivered Lumens: 2538
Input Watts: 35.9W
Efficacy: 71
Power Factor: 0.994
Total Harmonic Distortion: 5.39
CCT: 3926K
CRI: 84.1
Max Candela: 1495.772@ 7.5° from Vertical
Spacing Criterion (0-180): 1.24
Spacing Criterion (90-270): 1.06
Spacing Criterion (Diagonal): 1.10
2
1
Maximum Candela = 1495.772 Located At Horizontal Angle = 90, Vertical Angle = 7.5
# 1 - Vertical Plane Through Horizontal Angles (90 - 270)
# 2 - Vertical Plane Through Horizontal Angles (0 - 180)
Selux Corporation © 2016, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 12 of 13
(Rev. 10/2016)
L60_Rec_ss_v2.5
M60
LED Recessed
CCT Multiplier
4000K
1.000
3500K
0.968
3000K
0.987
2700K
0.939
90 CRI
Multiplier
4000K
0.884
3500K
0.924
3000K
0.880
CCT and CRI multipliers apply to the
photometry, IES files, and per foot values
listed on page one (light engine).
Light Engine Multiplier
Engine
Lumens
Watts
1A35
1.00
1.00
1A30
0.88
0.86
1A25
0.74
0.71
1A20
0.60
0.58
Light engine multiplier supplied for per foot
values listed on page one (light engine).
Selux Corporation © 2016, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 13 of 13
(Rev. 10/2016)
L60_Rec_ss_v2.5

Similar documents

M100 LED Recessed [L1Rx] selux.us

M100 LED Recessed [L1Rx] selux.us Length intended to fit centered between the grid for SG, TB, TBS, PMT mountings.

More information

M100 LED Direct [L10] selux.us

M100 LED Direct [L10] selux.us Luminaires supplied with A-series EcoSystem (4 wire, digital link) dimming driver programmed for Constant Current Reduction (CCR). For Pulse Width Modulation (PWM) dimming, please consult factory. ...

More information