WAUS Power Supplies CAT_02-2010

WE HAVE THE RIGHT
POWER SUPPLY
FOR YOUR APPLICATION
PLUS COMPLETE PEACE OF MIND WITH
HIGHEST QUALITY & PROVEN RELIABILITY
Switchmode Power Supplies
Australia Core Assortment
Catalogue & Price List 2010/2011
Power Supply Selection Considerations
Output Voltage
Overload Protection
Redundancy
ƒ All Weidmuller Switchmode Power
ƒ Overload thermal protection is built in
ƒ For
Supplies have a regulated output
voltage, that is the output voltage
remains constant irrespective of input
voltage or load current, provided the
supply voltage is within the specified
range. Some models can be powered
from DC as well as AC
to protect the power supply if the load
applied is in excess of the rated current,
for a period of time. This will shutdown
the output until the power supply cools
down, and will need to be reset by
disconnecting and reconnecting the
input supply.
redundant operation where
two identical power supplies are
connected in parallel, for reliability
and safety reasons the use of diode
auctioneering modules is necessary. In
this configuration there is no possibility
of a back feed from one power supply to
the other and supply failure alarms can
be operated.
Environmental
Short Ciruit Protection
Load Sharing
ƒ Environmental issues to consider are the
ƒ Short circuit protection is also built in so
ƒ When two or more power supplies are
ambient temperature where the power
supply is expected to operate. Note the
de-rating for high ambient temperature
use. Vibration in the area of use must
also be considered.
that if there is a short circuit in the load
circuit the power supply will shutdown
until the short circuit is removed, and
will auto start.
to be connected in parallel for power
sharing the output voltage of the power
supplies must be adjusted to be within
50mV of each other. To achieve this
the voltmeter being used must be
accurate and all test leads must be
securely connected when making the
adjustment, not just held or pushed
onto the terminals. The method of
wiring must also be done in the correct
configuration so as to avoid different
wire lengths when bridging the power
supplies. If possible the use of a single
higher output power supply is a better
option than parallel connect smaller
power supplies. It is often difficult to
get more than two parallel connected
power supplies to current share.
Power Boost
Mounting
ƒ All Weidmuller Switchmode Power
ƒ Mounting types available are “DIN”
Supplies have start up boost of up to
400%. This allows for non resistive
loads to be started. Inductive loads,
i.e. solenoid valves and motors, have
a starting current as high as six times
full load current, while capacitive loads,
i.e. some electronic devices and PLC’s
with input filtering capacitors have a
start up current of up to twelve times.
Switchmode power supplies have a
built in protection circuit which turns the
output off if a sudden load is introduced
which exceeds the rated load of the
power supply.
rail mounting or chassis / panel
mounting.
Method of operation
Primary switch-mode power supplies are distinguished by a
high degree of efficiency and also by their compact dimensions
and moderate generation of heat. The mains voltage is rectified
directly. The rectified voltage is then chopped with a higher
frequency than that of the mains frequency. A transformer –
which can be quite small due to the high switching frequency –
converts the voltage with the switching frequency to the
required value.
The voltage is now rectified and smoothed by a filter. This
regulator control itself is carried out by means of pulse-width
modulation. The on and off times of the chopper transformers
are regulated to ensure that the output voltage remains stable.
2
Power Supplies
CONTENTS
4-5
ECOLine
The price vs performance winner.
6-7
PRO-M
Advanced feature power supply in ultra compact housing.
8-9
PRO-H
For industrial and critical power requirements.
10
INSTAPower 25-48W
Versatile adjustable output voltages from 4 to 55Vdc.
10
INSTAPower 24W
Powering inductive loads. Up to 3 times starting current.
10
WAVEPower
Slimline fully protected power supply with plug / socket connections.
11
EasyLine
Panel mount stable and reliable power for machines.
Input
Voltage DC
Output
Voltage DC
Adjustable
Output
Voltage
Output
Current
Power
Boost at
start up
Stackable
Housing
ECOline
88-132/176-264
110-330
24
24-28
3 to 20
50% for 2 - 5s
Y
Metal
ECOline
3 Phase
340-575
X
24
24-28
10 to 40
50% for 2 - 5s
Y
Metal
PRO-M
85-264
80-370
24
22.5-29.5
3 to 40
120% for 2min
with
space
Metal
PRO-M
3 Phase
320-575
450-800
24
22.5-29.5
5 to 40
120% for 2min
with
space
Metal
PRO-H
85-132/187-264
N/A
24
24-28
3.75 to 25
N/A
Y
Metal
INSTAPower
25-48W
85-264
110-370
4 to 55
Y
1 to 5
N/A
Y
Plastic
INSTAPower
24W
85-265
120-300
5 to 28
N
1 to 2
400%
Y
Plastic
EasyLine
85-264
110-370
12, 24, 48
Y
1.1 to 10.5
150%
N/A
Metal
Power
Supply
Model
Input
Voltage AC
QUICK SELECTION GUIDE
3
ECOLINE
Efficient and Reliable DC Switchmode Power Supplies
Ventilation
Ventilation Channel for Side by Side
stacking with no derating
Indication
Output LED Power Indication
Robust
Robust metal housing mounts on TS35
DIN Rail
AC / DC
International use
Thanks to the wide range of inputs (85 V AC to 265 V AC), the
power supplies range is suitable for a wide variety of
applications. Local and International Approvals: C Tick, CE, UL,
CSA
4
Note: All prices above are list prices and standard customer discounts may apply.
All prices exclude GST. Weidmuller standard terms & conditions of sale also apply.
ECOLINE 1 & 3 Phase 72-960W
MAXIMUM PERFORMANCE vs PRICE
If you're comparing price with performance, the economical ECOLINE series is the
flagship of Weidmuller's range of switchmode power supplies. Packed with features
and with the same quality and reliability you've come to expect from Weidmuller, the
ECOLINE will not disappoint.
ƒ Robust metal housing
ƒ Mounts on TS35 Din Rail
ƒ Output LED power indication
ƒ Adjustable output 24-28Vdc for Voltage Drop Compensation
ƒ Wide range switchable supply input voltage
ƒ Built-in remote status alarm via C/O relay
ƒ Power diode module for parallel connection/redundancy
ƒ Built-in ventilation channel for side by side stacking & no de-rating
ƒ Up to 50% overload protection and auto restart (Power boost 2-5s)
ƒ Local and International Approvals: CTick, CE, UL, CSA
Max. Output
Power
Output
Current
Output
Voltage
Input
Voltage
Dimensions
(LxWxHmm)
Order
Number
List
Price
72W
3A
24-28 Vdc
85-264Vac/110-370Vdc
110 x 55.5 x 125
8708660000
$74.12
120W
5A
24-28 Vdc
88-132Vac/176-264Vac/250-370Vdc
110 x 65.5 x 125
8708670000
$88.73
240W
10 A
24-28 Vdc
88-132Vac/176-264Vac/250-370Vdc
110 x 125.5 x 125
8708680000
$163.39
480W
20 A
24-28 Vdc
88-132Vac/176-264Vac/250-370Vdc
110 x 227.5 x 125
8778870000
$275.00
250W
10 A
24-28 Vdc
3x400Vac/340-575Vac
110 x 125.5 x 125
8708700000
$173.00
480W
20 A
24-28 Vdc
3x400Vac/340-575Vac
110 x 227.5 x 125
8708710000
$260.00
960W
40 A
24-28 Vdc
3x400Vac/340-575Vac
125 x 280 x 150
8708730000
$440.00
1-phase
3-phase
ECOLINE Diode Modules
+
240V~
24V
-
E1
+
E2
DC
V
ECOLINE
Power Supplies
V
24V
Diode Module
+
240V~
-
DOUBLE YOUR POWER / REDUNDANCY
It is often necessary to connect two power supplies in parallel for increased load current
requirements or redundancy. The best solution to do this is to use a Diode Auctioneering
Module. These modules contain two full current rated diodes with a common cathode
connection. To install you simply connect the output of each power supply to the input
terminals of the diode module. A single output is then available from the diode module.
With this setup the power supplies can not drive each others output .
ƒ Robust metal housing
ƒ Mounts on TS35 Din Rail
ƒ Built-in ventilation channel for side by side stacking & no De-rating
ƒ Local and International Approvals: C Tick, CE, UL, CSA
Output
Current
Output
Voltage
Input
Voltage
Input
Current
Dimensions
(LxWxHmm)
Order
Number
List
Price
CP DM 10
0-20A max or 10A
redundancy mode
Vin-0.5
typical
40Vdc
max.
2 x 0-10A
max.
125x55.5x100
8710620000
$78.04
CP DM 20
0-40A max or 20A
redundancy mode
Vin-0.5
typical
40Vdc
max.
2 x 0-20A
max.
142x55.5x100
8768650000
$111.73
Type
Note: All prices above are list prices and standard customer discounts may apply.
All prices exclude GST. Weidmuller standard terms & conditions of sale also apply.
5
PRO-M
Power supplies for space-saving use in automation technology
from
33 m
m
Narrow
Space-saving configuration in the switching
cabinet through very narrow housing
construction and side-by-side connectability.
–25 °C
to
+70 °C
Robust
Wide temperature range from
–25 °C … +70 °C.
Parallel connection
Module power can be increased by connecting up
to five power supplies in parallel without diode
module.
AC / DC
International use
Thanks to wide-range input (both DC as well as AC voltages
can be used; no switching required) and extensive approvals
(UL/CSA and GL (EMC 1 - bridge).
6
Note: All prices above are list prices and standard customer discounts may apply.
All prices exclude GST. Weidmuller standard terms & conditions of sale also apply.
PRO-M
Small in Size, Big on Performance
PRO-M Advanced Feature
Switchmode Power Supplies
The optimal and reliable power supply for machinery. The solid, very narrow metal housing of the 10 different
versions of the 24 V DC supply enable installation without lateral spacing, thereby saving space on the DIN
rail .
AC and DC wide-range inputs and a broad temperature range enable universal use. Thanks to its high
efficiency, over load resistance and high performance reserves, the PRO-M is the reliable power supply in all
applications. Should one phase fail, the 3-phase PRO-M power supply modules continue to work reliably,
i.e. in two-phase operation.
ƒ The new PRO-M range of switchmode power supplies have a space saving of up to 50% and no gap
required between multiple units. PRO-M will squeeze into the tightest of switchboards or machines
ƒ Extended temperature Range of -25°C to +70°C extends the number of application possibilities
ƒ Power increasing with up to 5 modules is accomplished without the need for external diode modules
ƒ A Power boost up to 120% is provided for up to 2 minutes and with overall efficiencies of up to 90% the
new PRO-M series delivers in all areas
Powerful
Wide choice
Rated load
120 %
100 %
Power reserve
45 °C
60 °C 70 °C
Temperature
With additional power reserves at standard temperatures.
The right power supply for every application:
1-phase 3 A, 5 A, 7.5 A, 10 A, 20 A, 40 A and
3-phase 5 A, 10 A, 20 A, 40 A.
Max. Output
Power
Output
Current
Output Voltage
Input Voltage
Dimensions
(LxWxHmm)
Order No.
List Price
1-phase
70 W
3A
24 V (22.5 to 29.5 V)
85-264Vac / 80-370Vdc
125x33x130
8951330000
$99.00
120 W
5A
24 V (22.5 to 29.5 V)
85-264Vac / 80-370Vdc
125x40x130
8951340000
$129.00
180 W
7.5 A
24 V (22.5 to 29.5 V)
85-264Vac / 80-370Vdc
125x50x130
8951350000
$199.00
250 W
10 A
24 V (22.5 to 29.5 V)
85-264Vac / 80-370Vdc
150x60x130
8951360000
$219.00
500 W
20 A
24 V (22.5 to 29.5 V)
85-264Vac / 80-370Vdc
150x115x130
8951370000
$369.00
1000W
40 A
24 V (22.5 to 29.5 V)
85-264Vac / 80-370Vdc
150x140x130
8951380000
$779.00
3-phase
120 W
5A
24 V (22.5 to 29.5 V)
320-575Vac / 450-800Vdc
125x40x130
8951390000
$249.00
250 W
10 A
24 V (22.5 to 29.5 V)
320-575Vac / 450-800Vdc
150x60x130
8951400000
$315.00
500 W
20 A
24 V (22.5 to 29.5 V)
320-575Vac / 450-800Vdc
150x115x130
8951410000
$429.00
1000 W
40 A
24 V (22.5 to 29.5 V)
320-575Vac / 450-800Vdc
150x140x130
8951420000
$665.00
Note: All prices above are list prices and standard customer discounts may apply.
All prices exclude GST. Weidmuller standard terms & conditions of sale also apply.
7
PRO-H
Industrial Power Supplies for Extreme Requirements
Status Alarms
Green LED OK
Red LED OFF
–25 °C
to
+70 °C
Remote alarms
Robust
1G Vibration
15G Shock
Wide temperature range from
–25 °C … +70 °C.
Shock & Vibration Proof
Designed for use in areas of high shock and vibration
Reliable
Equiped for long reliable service life.
High Mean Time Between Failures
(MTBF) up to 1.8 Million hours.
8
Note: All prices above are list prices and standard customer discounts may apply.
All prices exclude GST. Weidmuller standard terms & conditions of sale also apply.
PRO-H
FOR EXTREME REQUIREMENTS
Single-Phase
Power Supplies
The PRO-H is a new generation of high performance DIN-rail mounted
single-phase power supplies designed to work reliably even under the most
demanding factory floor conditions. A high power reserve guarantees reliable
start-up of loads with high inrush currents such motor starting applications.
Excellent electrical specifications and high immunity against fluctuations in input
voltage makes these compact modules the best choice to power sensitive
loads in industrial process control systems, machine tools or other demanding
industrial applications.
ƒ Industrial grade design
ƒ Rugged metal case for harsh industrial environments
ƒ Autoselect input and international safety approvals
ƒ Variable output voltage
ƒ Indefinite short circuit, overvoltage and over temperature
protection
ƒ Power OK signal
ƒ Remote On/Off
ƒ Shock and vibration proof
ƒ Optional panel mounting
ƒ Redundancy module
Max. Output
Power
Output
Current
Output
Voltage
Input
Voltage
Dimensions
(LxWxHmm)
Order
Number
70 W
6.5 A
12 Vdc
85-132Vac / 187-264Vac
110x35x110
1105430000
140 W
13.0 A
12 Vdc
85-132Vac / 187-264Vac
110x54x110
1105440000
90 W
3.75 A
24 Vdc
85-132Vac / 187-264Vac
110x35x110
1105790000
180 W
7.5 A
24 Vdc
85-132Vac / 187-264Vac
110x54x110
1105810000
360 W
15 A
24 Vdc
85-132Vac / 187-264Vac
125x80x125
1105820000
600 W
25 A
24 Vdc
85-132Vac / 187-264Vac
125x165x125
1105840000
180 W
4A
48 Vdc
85-132Vac / 187-264Vac
110x54x110
1105850000
360 W
7.5 A
48 Vdc
85-132Vac / 187-264Vac
125x80x125
1105860000
600 W
12.5 A
48 Vdc
85-132Vac / 187-264Vac
125x165x125
1105870000
PRO-H Diode Modules
DOUBLE YOUR POWER / REDUNDANCY
With a redundancy module and two PRO-H power supplies (of same type)
you can configure a highly reliable, truly redundant power system without
any additional components. This module enforces the equivalent sharing of
the output current by each power supply. The system is fully redundant and
provides output power even if one power supply has completely failed e.g by
short circuit on the output. In the event that either power supply fails or is
disconnected, the second unit will automatically supply the full current to the
load. The redundancy of the system is monitored and if lost, indicated by an
alarm output. The inputs are hot swappable and can be loaded up to 15 A
each.
Output
Current
Output
Voltage
Input
Voltage
Input
Current
Dimensions
(LxWxHmm)
Order
Number
CP T RM 10
15A @ 24Vdc
@ 40°C
24 Vdc
2 x 24Vdc
15 A
110x35x110
1105880000
CP T RM 20
15A @ 24Vdc
@ 40°C
24 Vdc
2 x Control
Input
25 A
110x54x110
1105890000
Type
9
INSTAPOWER 1 Phase 25-48W
ADJUSTABLE OUTPUT VERSATILITY
The new INSTApower single phase 25-48W power supplies provide the answer to a
wide range of power supply needs. Just four different modules provide for all output
voltages from 4 to 55VDC. An easily accessible trimpot is provided via an access port
to enable wide adjustment to meet your requirements. Fully protected against overload
INSTApower 48W provides up to 50% over current drive to start your load.
ƒ Wide range of adjustment & universal AC/DC inputs
ƒ Suitable for use as a DC/DC Converter
ƒ Ultra-compact only 70mm wide
ƒ Mounts on standard TS35 DIN rail
ƒ Local and International Approvals: CTick, CE, UL, CSA
Max. Output
Power
Output
Current
Output
Voltage
Input
Voltage
Dimensions
(LxWxHmm)
Order
Number
List
Price
25 W
5A
4-8 Vdc
85-264Vac/110-370Vdc
62.5x70.0x90.5
8754960000
$103.55
48 W
4A
9-15 Vdc
85-264Vac/110-370Vdc
62.5x70.0x90.5
8754970000
$103.55
48 W
2A
15-28 Vdc
85-264Vac/110-370Vdc
62.5x70.0x90.5
8739140000
$93.74
62.5x70.0x90.5
8879230000
$103.55
48 W
1A
46-55 Vdc
85-264Vac/110-370Vdc
INSTAPOWER 1 Phase 24W
FOR DRIVING INDUCTIVE LOADS
Devices such as relays, contactors, solenoids and motors all require an initial starting
current many times their normal level. The compact INSTAPOWER range has the
capacity to supply the initial inrush current to start inductive loads and can actually
provide 3 times their rated output for a short duration.
ƒ Thermal overload protection & automatic restart
ƒ High Efficiency & universal inputs
ƒ Compact design only 52mm wide
ƒ Mounts on standard TS35 DIN rail
ƒ Suitable for use as a DC/DC converter
ƒ Local and International Approvals: C Tick, CE, UL, CSA
Max. Output
Power
Output
Current
Output
Voltage
Input
Voltage
Dimensions
(LxWxHmm)
Order
Number
List
Price
24 W
2A
5 Vdc
85-265Vac/120-300Vdc
62.5x52x90.5
9928890005
$148.79
24 W
1.5 A
12 Vdc
85-265Vac/120-300Vdc
62.5x52x90.5
9928890012
$143.88
24 W
1.5 A
15 Vdc
85-265Vac/120-300Vdc
62.5x52x90.5
9928890015
$143.88
24 W
1A
24 Vdc
85-265Vac/120-300Vdc
62.5x52x90.5
9928890024
$135.16
24 W
1A
28 Vdc
85-265Vac/120-300Vdc
62.5x52x90.5
9928890028
$135.16
WAVEPOWER 1 Phase 12W
ULTRA COMPACT ONLY 22mm WIDE
Compact design and powerful functionality make the WAVEPOWER a very valuable
solution to spacing problems in many applications.
ƒ Slimline only 22.5mm in wide with plug/socket terminals
ƒ Thermal overload protection & automatic restart
ƒ Mounts on standard TS35 DIN rail
ƒ Local and International Approvals: C Tick, CE, UL, CSA
Max. Output
Power
Output
Current
Output
Voltage
Input
Voltage
Dimensions
(LxWxHmm)
Order
Number
List
Price
12 W
0.5 A
24 Vdc
85-265Vac/120-300Vdc
92.4x22.5x112.4
9918840024
$300.84
10
Note: All prices above are list prices and standard customer discounts may apply.
All prices exclude GST. Weidmuller standard terms & conditions of sale also apply.
Easyline Chassis Mount
LONG SERVICE LIFE
EasyLine Chassis Mount Power Supplies in a
range of capacities
With outputs from 25 to 250 Watts in industry standard 12, 24 and 48Vdc versions. Efficiencies of up to 87% the new
“EasyLine” from Weidmuller can reduce your power requirements and extend overall service life of your equipment. International approvals and universal input voltages, “EasyLine “ can be installed into equipment bound for any market.
ƒ Up to 150% overload protection.
ƒ Stable DC output voltage
ƒ Wide range input AC/DC
ƒ OEM Product
ƒ Long life and high efficiency in a compact chassis mount housing fitted with fingersafe terminations.
ƒ Extended temperature ratings: -20 °C to 70 °C and a low 100mV ripple add value to the already high value package.
ƒ All models feature adjustable output voltage
250 Watt EasyLine with
forced coiling keeps size
to a minimum
Easily accessible
terminals with touch
safe cover
Max. Output
Power (Watts)
Output
Current
Output
Voltage
Input
Voltage
Dimensions
(LxWxHmm)
Order No.
List Price
25W
1.1 A
24 V
85-264 Vac / 110-370 Vdc
105 x 77 x 35
7760052036
$29.95
75W
6A
12 V
85-264 Vac / 110-370 Vdc
135 x 100 x 40
7760052043
$46.95
75W
3.2 A
24 V
85-264 Vac / 110-370 Vdc
135 x 100 x 40
7760052044
$49.95
75W
1.6 A
48 V
85-264 Vac / 110-370 Vdc
135 x 100 x 40
7760052045
$46.95
150W
6.5 A
24 V
85-264 Vac / 110-370 Vdc
205 x 100 x 50
7760052051
$69.95
250W
10.5 A
24 V
85-264 Vac / 110-370 Vdc
205 x 100 x 50
7760052054
$99.95
7760052061
$4.95
Accessories
Bracket 250W
Note: All prices above are list prices and standard customer discounts may apply.
All prices exclude GST. Weidmuller standard terms & conditions of sale also apply.
11
Weidmuller Power Solutions
Power Product
Distributors
Weidmuller is a leading manufacturer of Power Electrical and Electronic products that
are designed, tested and certified to the most stringent Australian and International
standards. The extensive ‘Power Products’ portfolio encompasses, devices, modules
and accessories essential to the requirements of Electrical Engineers, Electricians and
Technicians.
NSW: Sydney
Ramelec (NSW) Pty Ltd
Phone: (02) 9684 6700
Fax: (02) 9684 6722
[email protected]
Weidmuller ‘Power Products’ are used worldwide in switchboards, machines and vehicles
where ever electrical power is terminated, switched, conditioned or transformed. With
over sixty years of experience and our strict attention to quality, reliability and efficient
functionality Weidmuller is the sensible choice for all your power electrical and electronic
needs.
NSW: North & Central Coast
PDC Group (Aust) Pty Ltd
Phone: (02) 4952 5200
Fax: (02) 4952 9337
[email protected]
• Terminals
• Markers
• Industrial Multipole Connectors
• Power Supplies
• Relays & Optocouplers
• Surge Protection
• Enclosures
• Cable Glands
• Tools
• Accessories
NSW: South & Wollongong
Excell Control Pty Ltd
Phone: (02) 4272 1922
Fax: (02) 4272 2957
[email protected]
QLD
Ramelec (QLD) Pty Ltd
Phone: (07) 3899 1322
Fax: (07) 3899 1422
[email protected]
VIC
Quador (Aust) Pty Ltd
Phone: (03) 9874 7388
Fax: (03) 9873 5134
[email protected]
TAS
TAS Electrical & Engineering Supplies
Phone: (03) 6273 9855
Fax: (03) 6273 9866
[email protected]
Or contact your local distributor, reseller or wholesaler:
SA
Ramelec (SA) Pty Ltd
Phone: (08) 8374 2100
Fax: (08) 8374 2102
[email protected]
NT
Ramelec (NT) Pty Ltd
Phone: 1300 309 303
Fax: 1300 309 308
[email protected]
Weidmuller Pty Ltd (Head Office)
43 Huntingwood Drive, Huntingwood
NSW 2148
Phone +61 (0) 2 9671 9999
Fax +61 (0) 2 9671 9900
Email [email protected]
www.weidmuller.com.au
WA
JTDay Pty Ltd
Phone: (08) 9345 3388
Fax: (08) 9345 3068
[email protected]
NEW ZEALAND
Cuthbert Stewart Limited
Phone: +64 (0) 4 568 6156
Fax: +64 (0) 4 568 6056
[email protected]
Order Number: WAUS/PowerSupplies2010