docBondtech Brochure - Medical waste autoclaves
download 
Report Transcription
Bondtech Brochure - Medical waste autoclaves
TABLE OF CONTENTS SECTION I BACKGROUND AND QUALIFICATIONS SECTION II TECHNICAL INFORMATION SECTION III ENGINEERING DATA SECTION IV SPECIFICATIONS SECTION V AUTOCLAVE BAGS, REUSABLE CONTAINERS AND DISPOZ A FONE SECTION VI PRICING, TERMS AND CONTRACT SECTION VII PICTURES SECTION VIII BROCHURES SECTION I BACKGROUND AND QUALIFICATIONS B ONDTE C H C OR PORATI ON BIO-MEDICAL WA S T E T R E A T M E N T INTRODUCTION INSIDE THIS ISSUE: General Performance 2 Treatment Method 2 Technical Background 3 Design 3 Installations 3 Important factors 4 BONDTECH’S AUTOCLAVES: Cost effective medical waste treatment. ¨Custom design for independent customers needs. ¨Extensive experience in the Medical Waste sector. Bondtech Corporation specializes in the sale and manufacturing of Autoclaves and Autoclave Systems. Bondtech has designed, engineered and manufactured autoclave systems for technical industries such as aerospace composite, glass lamination, rubber vulcanizing, wood treating, infectious medical waste treatment, yarn setting and many other technical applications. Bondtech has supplied autoclaves and autoclave systems to the medical waste treatment industry for the treatment of infectious waste for more than 15 years. Bondtech has made a total commitment to ensure that our customers purchase a quality autoclave system that is environmentally safe, reliable, easy to operate and priced competitively. In an effort to assist our customers with reliable equipment as well as a one-stop accountable supplier, Bondtech is offering the following auxiliary equipment and accessories: 1. 2. 3. 4. 5. 6. 7. 8. 9. Shredders for biomedical waste, sharps and paper destruction. Bin dumpers Aluminum and Aluminum bins Autoclavable bags Red bags and Chemo bags Reusable medical waste containers Compactors and balers Scissor lifts Boilers and more Bondtech has made a total commitment to provide the best possible service available. We offer a complete one-stop facility and turnkey service to improve pricing and customer accountability. Our ability to provide high quality equipment at competitive prices has made us the proven leader in the autoclave market and it has given us the respect of the industry. ¨Complete line of equipment and accessories for the medical waste industry. Bondtech is the largest manufacturer and supplier of commercial medical waste autoclave systems in the world. ¨Advance commercial and on-site technology S E RV I C E S O F F E R E D ¨ Complete turnkey installation and maintenance service. ¨ Evaluation of equipment requirements to satisfy market conditions. ¨ Identification and specification of equipment for plant or business applications. ¨ Design fabrication and supply of autoclaves, Hospital—Bondtech Autoclave Installation vacuum pumps, material handling systems, boilers, shredders, balers, compactors, roll-off containers, waste bins, autoclavable bags and misc. bags. ¨ Development and performance of maintenance management and quality control. ¨ Creation of training program to improve performance and/or acquaint company personnel to operate equipment properly and efficiently. Page 4 GENERAL PERFORMANCE Process Description: Bondtech Autoclave System’s are high vacuum, high pressure systems. Bondtech autoclaves are “PROVEN AND RELIABLE MEDICAL WASTE TREATMENT SYSTEM” subject to a pre-vacuum cycle, pulsating saturated steam cycle, and a post vacuum cycle to facilitate faster and more uniform penetration of steam into the medical waste to be treated. Bondtech Autoclave System’s high vacuum is achieved by using a top of the line liquid seal vacuum pump or a steam ejector. Bondtech Autoclave System’s locking ring, quick opening door is used in the most sophisticated aerospace autoclaves, and designed with safety in mind. In this particular design, the door is stationary and the locking ring is mounted on the periphery of the vessel and is rotated through a short arc by hydraulic or pneumatic cylinders located on the side of the vessel. TREATM E NT METHOD Bin Loading: Autoclave bins are loaded with infectious waste and are transferred into the autoclave vessel for treatment. This process can be performed by an automatic conveying system, in the most sophisticated commercial operations, or manually in smaller commercial and on-site operations; the door is closed, automatically or manually; and the operator is able to start the preprogrammed cycle by pushing a “start” button. Treatment: After the autoclave door is closed the following steps are performed by the preprogrammed controller. The first step is the pre-vacuum process. A vacuum of 24"28" Hg. is pulled during the pre-vacuum to evacuate the air from the vessel and to expedite and insure good steam penetration into the infectious medical waste. Steam ramps up the autoclave (275-305 Deg. F.). The waste load is then soaked at temperatures to meet the State regulations and to effectively treat the waste to render it noninfectious and safe for final disposal. Venting is performed through a steam condenser resulting in no steam being released into the atmosphere. The post vacuum cycle removes residual steam from the autoclave, flashes residual liquids drying the waste, minimizes the associated treatment smell and insures a safer environment for the operator and workers in the floor area. On-site hospital operation depicting: Aluminum bins, shredder, bin dumper and Bondtech’s autoclave. Record Keeping: Bondtech Autoclave Systems have an automated chart re- corder at the control panel which continuously records the temperature, vacuum and pressure. This information is maintained on permanent, hard copy records for each load of medical waste treated, further complying with quality control and satisfying environmental regulatory requirements. Unloading: Once the cycle is completed, the autoclave will illuminate a green light showing the cycle is complete and the door is ready to be opened. The operator will then unload the autoclave and the bin dumper will empty the bins into a compactor or a shredder. Shredders: Bondtech Autoclave Systems shredders are heavy duty, single or double stage shredders to meet required particle size. Each knife configuration has been designed to suit the material for maximum throughputs and optimum size. Advantages and Waste Volume Reduction: After autoclaving the waste volume is reduced by approximately 45-50%. Further reduction can be realized with the installation of an optional shredder. The major advantages of steam sterilization are the low costs associated with this process as well as the reliability of this well known technology. Page 5 T E C H N I C A L BAC KG RO U N D Bondtech has designed, supplied and installed more than 100 waste autoclaves/ sterilizers for the treatment of infectious medical waste for commercial operations processing more than 3.0 million pounds per day. These large autoclave systems have been designed in accordance with our customers requirements; follow EPA guidelines and regulations; and have been designed making sure decontamination of the waste occurs. In order to insure proper decontamination, Bondtech offers a pre-vacuum cycle to facilitate faster and more uniform steam penetration into the infectious waste to be treated and a post vacuum to insure a dryer end product and reduction of nuisance odors. The control system provides automatic sequencing and operation of the system and also records and provides data on every cycle of operation. Bondtech has a track record and a very good reputation in the Industry. Commercial—Bondtech Autoclave Installation BONDTECH’S DESIGN ¨ Ruggedly Designed and Built for Commercial Use ¨ Hydraulic Quick Opening Door/with Safety Pin Interlock ¨ Vacuum Pump or Vacuum Ejector for High Vacuum Operation ¨ Temperature Probes for Added Protection Assurance ¨ Programmable Control Systems ¨ Recorders ¨ Packaged and Modularized for Easy Installation ¨ Volume Reduction Achieved by the Vacuum Cycle and the Heat Cycle and Further Reduced if Shredding ¨ Weight Reduction at Time of Final Disposal Achieved by Removal of Moisture ¨ Built in Strict Accordance with the ASME Boiler and Pressure Vessel Code, Section VIII, Division 1 W OR L D W I D E INSTALLAT IO NS Bondtech’s medical waste autoclaves are operating in: United States: Arkansas, Alabama, California, Colorado, Florida, Georgia, Illinois, Iowa, Kansas, Kentucky, Louisiana, Michigan, Minnesota, Mississippi, Missouri, New Mexico, New York, Oklahoma, Pennsylvania, Puerto Rico, South Carolina, Tennessee, Texas, Virginia. International: Argentina, Canada, Korea, Mexico, Peru, Qatar, Thailand and the Philippines BONDTECH IS THE LEADER IN BIOMEDICAL WASTE AUTOCLAVES BONDTECH CORP ORATION ADDITIONAL PRODUCTS BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 We are on the web! www.bondtech.net ALUMINUM CARTS AUTOCLAVABLE LINERS COMPACTORS/ CONTAINERS/ DUMPERS SHREDDERS AUTOCLAVE SYSTEMS FEATURES: No Shredding prior to treatment: ¨ No potential aerosilization of pathogens. ¨No bloodborne pathogen exposure ¨Minimizes occupational exposure High vacuum system: ¨Ensures effective medical waste treatment ¨No residual steam exposure ¨Controls nuisance odors High pressure/temperature: ¨Insures effective medical waste treatment ¨Log 6 or better reduction against Bacillus stearothermophilus ¨Reliable proven technology ¨Largest company providing commercial medical waste systems ¨Experienced in medical waste since 1983 Simple and Safe System: ¨Safe Operation ¨No personal contact with infectious medical waste ¨No personal contact with sterilized medical waste ¨Minimal moving parts ¨Sing le push button ¨Automated System BAGS: Autoclavable, red, chemo & more WASTE CONTAINERS I M P O RTA N T FAC T O R S T O CONSIDER: In the United States, the steam autoclave is the most popular and cost effective medical waste treatment technology. Unlike the incinerator, the autoclave technology does not generate any hazardous combustion air pollutant emissions, such as hydrochloric acid, carbon monoxide, dioxin/furnans, metal (particulate matter), etc. The autoclaved medical waste byproduct is sanitized and safe for landfill disposal. More than 90% of the newly permitted commercial medical waste facilities since 1990 employ state of the art autoclave technology. Bondtech Corporation was awarded more than 90% of the contracts making Bondtech Corporation the worlds largest supplier of commercial medical waste treatment systems. Today, landfills across the world where medical waste is regulated accept autoclaved medical waste. Medical waste that is properly steam autoclaved is rendered noninfectious and safe for disposal at sanitary landfills. The autoclaved medical waste does not exhibit any leachate characteristics (heavy metals, etc.), as found in ash generated by incinerators. Autoclaved medical waste basically consists of approximately 75% paper and plastic, 22% fluff (cloth) and 36% pathological (body parts). In the United States, body parts are generally incinerated. To maximize landfill space, autoclaved medical waste can be safely compacted to achieve 60% volume reduction. Further reduction can be realized by installation of an optional shredder. The shredding process is performed only after the waste has been treated by the Bondtech Autoclave System. No shredding is ever performed prior to treatment. The autoclave technology has been thoroughly proven and Bondtech Autoclaves have been tested for more than 15 years in the United States. Today the bulk of the medical waste treatment capacity is by autoclave technology. BONDTECH IS READY TO HELP YOU DESIGN YOUR MEDICAL WASTE FACILITY. PLEASE DO NOT HESITATE TO CALL. TEL.: 800-414-4231 BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] CUSTOMER REFERENCES CUSTOMER & LOCATION Arcadia Composites/Petroleum Helicopter LaFayette, LA Mr. Frank Carter Phone: 318-237-6070 Fax: 318-237-6560 CUSTOMER & LOCATION NOVA COMPOSITES Mukilto, WA Mr. Greg Strand Phone: 425-347-4875 Fax; 425-347-0603 Sioux Manufacturing Corp. Fort Totten, ND Mr. Dana Grow Phone: 701-766-4211 Fax: 701-766-4359 R&F Products, Inc. Northridge, Ca. Mr. Findley Vanderby Phone: 760-929-8888 Fax: 760-929-8887 Nasa Marshal space Flight Center Marshall SFC, Al. Mr. Tracy Lamm Tel.: 256-544-0328 Fax: 1390 Architectural Safety Glass. Ft. Pierce, Fl. 34951-4110 Mr. George Sutorka Tel.: 561-467-0006 LAS Composites Paris, CA Mr. Gonzales Tel.: 909-657-0882 Fax: 909-940-5400 R&F Products, Inc. Northridge, CA Mr. Findley Vanderbey Tel.: 818-831-6699 Fax.: 760-929-8887 Cadillac Rubber Cadillac, MI Mr. Curt Reid Phone: 616-775-6571 ADTECH, INC. 19-10 Uchikanda, Chiyoda, KU Tokyo, Japan - Mr. Harada Phone: 3-3292-8455 Composites International Tulsa, OK Mr. Stoney Burke Phone: 918-834-2346 Fax: 918-834-6748 General Dynamics Corp. Fort worth, TX. 76101 Mr. Bill Karlela Phone: 817-777-3466 Foster Miller Walson, MA Mr. Victor Leemon BAE Automated Systems Dallas, TX. Ms. Mary Malone Fax.: 972-389-6480 Phone: 972-245-9411 Vision Composites Torrance, CA Mr. John Bartholomew Phone # changed GEC Marconi Materials San Diego, CA Mr. Martin Moran Phone: 909-947-7600 Fax.: 909-947-1823 Guardian Industries, Corp. Auburg Hills, Mi 48326 Mr. Tim Lemon Phone: 248-340-2245 Rogers South Windham, CT. Ms. Darline Taylor Phone: 860-423-6323 Fax.: 860-423-6120 BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] CUSTOMER & LOCATION National Glass, Ltd. Langley, B.C., Canada Mr. Marty Nixon Tel.: 604-530-2311 Fax.: 604-530-3222 CUSTOMER & LOCATION Brunswick Defense/Lincoln Compsites 4300 Idustrial Ave. Lincoln, NB 68504 Ms. Jannet Niemeyer Tel.: 402-464-8211 Fax.: 402-464-8729 Valmet-Sandy Hill, Inc. 27 Allen Street Hudson Falls, NY 12839 Mr. Kari Rajala Phone: 518-747-3381 Fax.: 518-747-1541 Engineers Fabrics Corp. Rockmart, Jga. Ms. Susan Daniels Phone: 770-684-7855 Fax.: 770-684-1634 Hexel/Heath Tecna Kent, Wa 98032 Mr. Tony Page Phone: 253-872-7500 Bonded Technology Cromwell, Ct. Mr. Robert E. Miller Phone: 860-635-1150 Fax.: 860-635-9585 Atlantic Roller Baltimore, Md 21237-2320 Mr. John Baldwin Phone: 410-687-7188 Valley Roller Fruitvale, Texas 75127 Mr. Bill Hunt Phone: 903-962-6024 Browning Ferries Industries (BFI) Lake City, GA Mr. Steve Shinner Tel.: 612-641-0009 Browning Ferries Industries (BFI) Sheridan, NY Mr. Don Kaminski Tel.: 716-366-4444 Browning Ferries Industries (BFI) Puerto Rico Mr. Steve Shinner Tel: 651-641-0009 Browning Ferries Industries (BFI) St. Paul, MN Mr. Steve Shinner Tel.: 651-641-0009 MED-X Miami, FL Mr. Frank Piriski Tel.: 305-885-4004 MED-X Eaton Park, FL Mr. Frank Piriski Tel.: 304-885-4004 MED-X St. John The Baptist Parish, LA Mr. Frank Piriski Tel.: 305-885-4004 SYSTEMS SOUTH APPLIED Beaver Dam, KY. (Now BFI) Mr. Dave Schoonmaker Tel.: 303-526-9778 Baptist Regional Medical Center Corbin, KY Mr. Clay Newman Tel.: 606-528-1212 Med-Tech Toronto, Ontario, Canada Mr. Dave Morrison Tel.: 905-791-3545 Darob, Inc. Louisville, KY. Mr. Robert Ford Tel.: 502-491-1535 Duval Medial Disposal, Inc. Jacksonville, FL Mr. William Olson Tel.: 904-354-7666 BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] CUSTOMER & LOCATION Medical Systems, Inc. St. Louis, MO Mr. Regis Hillow Tel.: 314-644-0100 CUSTOMER & LOCATION STERIMED, S.A. de C.V. Mexico City, Mexico Ms. Yesica Paredes Tel.: 011-525-626-5467 STERIMED, S.A. DE C.V. GUADALAJARA, MEXICO Ms. Yesica Paredes Tel.: 011-525-626-5467 American Medical Disposal Oklahoma City, OK Mr. Kent Robertson Tel.: 405-557-0024 Ogden Aviation Los Angeles, CA Mr. John Coughlin Tel.: 310-215-4555 Veterans Administration Hospital Fayetteville, AK Mr. Tom Miller Tel.: 501-444-5010 NEW YORK ENV. Oneontta, NY. Mr. David Schoonmaker Tel.: 607-432-9330 GENESIS ENVIRONMENTAL Pittsburgh, PA Mr. Jim Moritz Tel: 412-672-0400 ORB, INC. Seoul, Korea Ms. C. H. Lee Tel.: 206-441-6442 Southern Medical Disposal Nashville, TN Mr. John Needham Tel.: 512-476-7806 Texas Environmental Austin, TX John Needham Tel. 512-476-7806 Jackson Memorial Hospital Miami, FL Mr. Ron Bogue 305-585-1302 Medical Waste Management Brampton, Ontario Dan Kennedy Phone: 905-789-6660 Fax.: 905-789-6661 Jeff Anderson Regional Hospital Meridian, Mississippi Larry Townsand Tel.: 601-553-6196 Medical Waste Services of America Canton, Mississippi Gary Disotell Tel: 800-287-1726 Alhamad Trading Doha, Qatar St Francis Medical Center Peoria, Illinois David Volz Tel.: 309-655-2860 St. Joseph Medical Center Bloomington, Illinois David Volz Tel.: 309-655-2860 CGH Medical Center Sterling, Illinois Ken Millhouse Tel: 815-625-0400 Steritronix, Inc. Miami, Florida Travis Tel.: 954-931-7085 Aircraft Rubber Mfg. Co. Bend, Oregon 97701 Steve Russel Tel.: 541-388-0307 Advance Roller 212 Lewis Ct. Corona, Ca. 92882-1812 Tel.: 909-272-3010 BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] CUSTOMER & LOCATION CUSTOMER & LOCATION Acadian Composites LaFayette, La 70507 Brady Piorrier Tel.: 337-237-6070 Eagle Elastomer Cuyahoga Falls, Ohio 44224 Regal Makel Tel.: 330-923-7070 Flowers Hospital Dothan, Alabama MCM Engineers & General Contractors (Jackson Memorial) Miami, Florida Jose Fernandez Tel.: 305-324-6587 Mid-South Roller Co. Clarksville, Arkansas Robbie Mooney 501-754-6993 St. Lukes Hospital Manila, Philippines Rashomon Industries Lima, Peru Salisbury Machinery Salisbury, N.C. MUSC Charleston, S.C. Pat Mckitrick University of South Alabama Shredder Only Celsius Caguas, Puerto Rico Angel Perez Tel.: 787-743-2731 KOREA QATAR M E X I C O UNITED STATES C H I L E BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] MEDICAL WASTE ARTICLE FEATURING BONDTECH CORPORATION SECTION II TECHNICAL INFORMATION BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] TREATMENT OF INFECTIOUS WASTE Introduction The purpose of treating infectious waste is to change its biological character so as to reduce or eliminate its potential for causing disease. Incineration and steam sterilization are the most frequently used infectious waste treatment techniques. However, autoclaves have become the most popular medical waste treatment technology in the past few years. Since 1990 more than 90% of newly permitted commercial medical waste treatment capacity in the United States went to autoclave systems. Bondtech Corporation was awarded more than 90% of the contracts making Bondtech Corporation the largest commercial medical waste manufacturer in the world. the effectiveness of steam sterilization). Other indicators which monitor the treatment process may be used. However, it is recommended that the appropriateness and reliability of these indicators be confirmed before they are used to monitor infectious waste treatment. It is essential that indicators be properly placed within the waste load so that they will indicate accurately the effect of treatment of the entire waste load. Therefore, to Following is a list of other alternative assure accurate monitoring, the biological processes used to treat infectious waste: indicator should be distributed throughout ·Gas/vapor sterilization the waste load. ·Chemical disinfecting Monitoring is essential in develop·Microwave technology ment of standard operating procedures for ·Irradiation each treatment technique to verify that the ·Others treatment process is effective. Monitoring also permits refinement of the operating proMonitoring cedures that excess processing can be avoided A convenient approach to determine treatment effectiveness is the use of biological indi- while savings are realized in expenditures of time, energy and/or materials. Subsequently cators. Biological indicators are standardization products that are routinely used to demonstrate the periodic monitoring serves to demonstrate sterilization, thereby confirming that proper effectiveness of the treatment process. It is now current practice to use spores of a resistant strain of procedures were used and that the equipment was functioning properly. some particular bacteria species for testing each specific treatment process. The United States PharmaSteam treatment of infectious waste copoeia recommends the use of biological indicators utilizes saturated steam within a pressure vesfor monitoring treatment processes such as steam sel (known as a steam autoclave, sterilizer, or sterilization, incineration and thermal inactivation. retort), at temperatures sufficient to kill infecThere are other indicators that provide an tious agents present in the waste. There are two general types of instantaneous indication — usually by a chemically steam autoclaves - the gravity displacement induced color change — of the achievement of a certain temperature. However, these indicators are type in which the displaced air flows out the drain through a steam-activated exhaust valve, not suitable for use in monitoring the sterilization process because each treatment technique involves and high vacuum type, in which the vacuum a combination of factors; therefore, no single factor is pulled to remove the air before steam is is a valid criterion for indicating the effectiveness of introduced to the chamber. the sterilization process. (For example, in steam treatment, the waste must be exposed to a certain temperature for at least a minimum period of time in order to achieve disinfection. Therefore, any indicator that indicates only the attainment of a particular temperature is not suitable for monitoring Bondtech Autoclave Systems are supplied with an industrial grade vacuum pump to pull 28" HG pre-vacuum to void autoclave chamber of air before induction of steam treatment. After the steam treatment is completed, the unit then pulls a post vacuum that voids the autoclave chamber of moisture and odor. The moisture/condensed steam is scrubbed and filtered during the post vacuum cycle and the result is drier waste than what you started with, and with virtually no odors. With both types, as the air is replaced with pressurized steam, the temperature of the treatment chamber increases. This results in temperature increases within the waste load which under most conditions are sufficient to treat the waste Treatment by steam sterilization is time and temperature dependent; therefore, it is essential that the entire waste load is exposed to the necessary temperature for a defined period of time. (Heating the containers and the waste usually lags behind heating of the chamber. Bondtech Autoclave Systems are very efficient with total cycle time within approximately one hour. In steam sterilization, decontamination of the waste occurs primarily from steam penetration. Heat conduction provides a secondary source of heat transfer. Therefore, for effective and efficient treatment, the degree of steam penetration is the critical factor. For steam to penetrate throughout the waste load, the air must be completely displaced from the treatment chamber. The presence of residual air within the sterilizer chamber can prevent effective sterilization by reducing the ultimate possible temperature of the steam, regardless of the pressure; causing variation in temperature throughout the chamber, prolonging the time needed to attain the maximum temperature, and inhibiting steam penetration into porous materials Bondtech Autoclave Systems are full vacuum thus eliminating the chance for inadequate disinfection. Factors that can cause incomplete displacement of air include: improper loading (which may prevent the circulation of steam within the chamber), and use of individual heat resistant plastic bags. BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] The principal factors that should be considered when treating infectious waste by steam are: ¨ Type of waste ¨ Packaging and containers ¨ Volume of the waste load and its configuration in the treatment chamber TYPE OF WASTE Infectious waste with low density (such as plastics) is more amenable to steam disinfections. High density waste such as large body parts, and large quantities of animal bedding and fluids inhibit direct steam penetration and require longer disinfections time. Alternative treatment methods should be considered (i.e., incineration) for these wastes. PACKAGING AND CONTAINERS A variety of containers are used in steam sterilization including plastic bags, metal pans, bottles, and flasks. One consideration with plastic bags is the type and thickness of the plastic and its suitability for use in steam treatment. There are some plastic bags which are marketed as autoclavable (i.e., they are heat resistant and do not melt). These bags are constructed of high density polyethylene or polypropylene and help keep the autoclave carts clean. Bondtech autoclave carts can be Teflon coated in order not to use autoclavable bags, or Bondtech can supply a low price heat resistant bag. Bondtech Autoclave Systems full vacuum will bust sealed containers thus providing excellent steam penetration. VOLUME AND CONFIGURATION OF THE WASTE LOAD The volume of the waste is an important factor in steam disinfecting as it can be difficult to attain sterilizing temperatures in large loads. Many infectious wastes that have multiple hazards should not be steam disinfected. Infectious wastes that should not be disinfected include those that contain antineoplastic drugs, toxic chemicals, or chemicals that would be volatilized by steam. Persons involved in steam disinfecting waste should be educated in proper techniques to minimize personal exposure to the hazards posed by these wastes. These techniques include use of protective equipment, minimization of aerosol formation, and prevention of spillage of waste during autoclave loading. Bondtech provides through operation and maintenance training. A chart recorder should be used to ensure that a sufficient high temperature is maintained for an adequate period of time during the cycle. Bondtech Autoclave Systems are supplied with two temperature recorders - (1) stationary and (1) in the chart recorder. Failure to attain or maintain operating temperature may indicate mechanical failure. All steam autoclaves should be routinely inspected and serviced. Monitoring the steam process is required to ensure efficient treatment. The process should be monitored periodically to check that proper procedures are being followed and that the equipment is functioning properly. Bacillus stearothermophilus is recommended by the United States Pharmacopoeia as the biological indicator for monitoring steam sterilization/disinfecting. There are other indicators that may effectively monitor the treatment process; however, because steam disinfecting is time and temperature dependent, any indicator that is used should effectively monitor both of these factors REPRESENTATIVE DRAWINGS BONDTECH ON– SITE AUTOCLAVE BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] REPRESENTATIVE DRAWINGS BONDTECH COMMERCIAL UNITS BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] SECTION III ENGINEERING DATA BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] PROVEN MEDICAL WASTE TREATMENT SPECIAL EQUIPMENT FEATURES • Ruggedly Designed and Built for Commercial Use • Hydraulic Quick Opening Door • Liquid Ring Vacuum Pump or Steam Ejector for High Vacuum Operation • Programmable Control System • Recorders for Pressure & Temperature • Packaged and Modularized for Easy Installation • Removal of Moisture for Less Weight at Time of Disposal Built Under ASME Boiler and Pressure Vessel Code, Section VIII, Div1 PROCESS DESCRIPTION Bondtech Autoclave Systems are subject to a pre-vacuum cycle, pulsating saturated steam cycle, and a post vacuum cycle to facilitate faster and more uniform penetration of steam into the medical waste to be treated. Bondtech Autoclave Systems high vacuum is achieved by using a top of the line liquid seal vacuum pump or a steam ejector. Bondtech Autoclave Systems locking ring, quick opening door is used in the most sophisticated aerospace autoclaves. In this particular design, the door is stationary and the locking ring is mounted on the periphery of the vessel and is rotated through a short arc by hydraulic or pneumatic cylinders located on the side of the vessel. The meeting surfaces of the lugs on both the locking ring and door are tapered circumferentially at a slight angle to secure a wedging action which forces the door against a gasket to secure a pressure tight joint. BIN LOADING Infectious waste is loaded into the autoclave bins, which are located at the loading area. The bins are then loaded into the autoclave, the door is closed and the operator is able to start the cycle. TREATMENT After the autoclave door is closed the following steps are performed by the preprogrammed controller. The first step is the prevacuum process. The pre-vacuum is used to evacuate the air from the vessel and to expedite good steam penetration into the infectious medical waste. 28" +/- of vacuum is used. Steam ramps up the autoclave to 285 Deg. F. The waste is then soaked at temperatures from 285 Deg. F. to 305 Deg. F. (in accordance with state regulations) and for a predetermined time. The post vacuum is used to dry (“flash”) the load and to reduce the associated treatment “smell. The pre and post vacuum air is properly filtered. RECORD KEEPING When the autoclave door closes, the sterilization cycle begins and the record keeping starts. The recording chart at the control panel automatically records date, time, temperature and vacuum for each cycle. This information will be maintained on a permanent, hard copy record. UNLOADING Once the cycle is completed, the autoclave will show a green light showing the cycle is complete and the door is ready to be opened. The operator will then unload the autoclave. The bin will be manually unloaded from the autoclave. A bin dumper will empty the bin into a compactor or shredder (Optional Equipment). SAFETY FEATURES The Bondtech Autoclave Systems cycle time and requirements are preset to insure proper treatment of the infectious medical waste. Only qualified personnel will be able to change the cycle. There will be a printed record of the time, temperature and pressure achieved during the cycle. The Bondtech Autoclave System is fully insulated for safe and effi- cient operation. EMERGENCY SHUTDOWN Emergency shut down “Push Button” will be provided for worker’s safety. Workers are able to temporarily shut down the system whenever it is necessary. TRANSPORT TO LANDFILL The treated waste can in most cases be sent directly to the landfill. Bondtech offers optional equipment such as: proven medical waste shredders, self-contained compactors/ containers. OPTIONAL EQUIPMENT Bondtech offers auxiliary equipment for a complete medical waste treatment facility, including but not limited to: • Medical waste shredders • Self-contained compactor/containers and balers • Reusable medical waste containers (including sharp containers) • Autoclavable bags, red bags • Conveyer Systems EQUIPMENT OPERATOR TRAINING All employees will receive training and will become knowledgeable of the procedures, equipment and infectious medical waste treatment process. Training programs are oriented toward maintenance and operation of the facility. GENERAL Bondtech Autoclave Systems will be constructed for a maximum allowable working pressure of 75 PSI @ full vacuum. The loading arrangements are horizontal. DESIGN The autoclave will be designed, fabricated and tested in accordance with the ASME, Section VIII, Division 1, Boiler and Pressure Vessel Code. It will be fabricated of carbon steel plate, “pressure vessel quality” steel, well-suited to your requirements. The vessel will be designed for full vacuum. Our in house engineering design capabilities allow us to design our systems per our customer’s needs and specifications. BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] SYSTEM DESCRIPTION Door: The autoclave will be provided with a quick opening door. This is a breech lock type door, which does not produce any relative motion between the door and the pressure sealing o-ring. The door design operates by rotating the locking ring a few degrees to expose the door lugs through cut out areas of the lock ring. The door is simply pivoted 90 degrees to allow full access to the interior. The door is completely interlocked to prevent operation when pressure is present in the autoclave. Sizing the hydraulic components, directional control valve, hydraulic cylinders, etc. allow use of a one ½ HP hydraulic power unit for quick and efficient door operation. The door safety interlock device includes mechanical, pneumatic and electrical interlocks to prevent inadvertently opening the door under pressure. It also complies with Section UG-35(B), (1) AND (2) of the ASME code. A limit switch and “low pressure switch” are also provided for connection into the control system for electrical interlocks as well. Supports: Saddles will be provided for support: The front saddle will be fixed with provisions to allow the rear saddle to slide to accommodate thermal expansion. Tracks: Internal tracks will be provided. The configuration and location will be coordinated with the design of the lift table. Insulation: The exterior of the autoclave will be insulated with 2" of insulation which will then be covered with a polypropylene cover for both heat loss reduction and personnel protection. Some surfaces will not be insulated, such as the door, locking ring and hinge mechanism, support saddles, etc. These exposed surfaces will be painted with an industrial enamel. Code Papers: A U1-A manufacturer’s data report for pressure vessels will be provided. Manuals & Drawings: Two complete sets of operational and maintenance manuals will be provided. Controls: Microprocessor control system for autoclaves with instruments to monitor and control the autoclave, and the valve actuator and support equipment necessary to provide a complete operating system to perform the following operations will be included. • The autoclave will be initiated with a “CYCLE START” push-button. Automatic cycling will be initiated with no operator interaction necessary. A selector switch will allow “MANUEL” or “AUTOMATIC” operation. • Pre-Vacuum: The vacuum system will start and evacuate the autoclave 24-27" Hg. • Steam: A pneumatically actuated proportional steam control valve will then open and control steam based on the temperature of an internally located thermocouple. Upon reaching the set temperature a timing sequence will commence. A feature of the controller is the ability to perform a “guaranteed soak” which ensures that the temperature is at the programmed setting for the programmed time. • Blow-down: At the completion of the preset time the autoclave will be vented out through a steel condenser/ silencer. Upon reaching atmospheric pressure a “CYCLE COMPLETE” lamp will indicate to the operator that the door may be opened. Post-Vacuum: the final sequence will be the post vacuum, which will flash “dry” the load, removing any residual steam, for operator’s safety and weight reduction and minimizing odors. Recorder: A three pen chart recorder will be provided to record temperature, pressure and vacuum. Control Panel: The control panel will be a free standing NEMA 12 rated electrical enclosure with indicators, push-buttons, main disconnect, motor controls for hydraulic power unit and vacuum system, temperature controller, recorder and all associated wiring, fusing, etc. All wiring will be terminated on a numbered terminal strip for easy field installation. Steam controls include the proportional control valve described above plus a steam trap station. This includes a steam trap, block and bypass valves, strainer and check valves. A strainer and blocking valve are provided at the inlet also. Vacuum: The vacuum will be achieved through a vacuum pump or a steam ejector capable of pulling 24-28" Hg of vacuum. There will be a pre-vacuum cycle which will remove excess air from the waste load in order to allow for even steam penetration through the entire waste. The air removed during the pre-vacuum process will be mixed with heated steam at 308 Deg. F. and thereafter condensed and drained to the sewer system. The post-vacuum cycle removes the excess steam from the vessel and expedites the steam purging process. This process allows for a much drier end-product and also excess steam from being discharged into the work area when opening the autoclave door. The vacuum system will require approximately 5 to 15 gpm of water for service liquid. Material Handling: The bins will be manually rolled in and out of the vessel. Condenser: One properly sized spray condenser to handle the steam purge from the autoclave system will be provided. The steam will be condensed and drained to the sewer. Waste Bins: Waste bins will be properly sized for each model of autoclave. We will provide enough bins for one load. Additional bins can be obtained (prices will be quoted upon request). BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] OPTIONAL EQUIPMENT: In order to provide our customers with a one-stop supply house, we are pleased to supply the following equipment: MEDICAL WASTE SHREDDERS BALERS AUTOCLAVABLE BAGS, RED BAGS REUSABLE SHARP CONTAINERS REUSABLE MEDICAL WASTE CONTAINERS CONVEYOR SYSTEMS BIN DUMPERS SELF-CONTAINED COMPACTOR/ CONTAINERS SHREDDER: Based on the size of the autoclave, Bondtech Autoclave Systems can offer heavy duty shredders to render the medical waste unrecognizable. Based on the requirements, we can offer single or double stage shredders. Double stage shredders are used when the particle size has to be smaller. Each knife profile and configuration has been designed to suit the material for maximum throughput and optimum shred size. • • • • Optional features include: PLC interfacing for peripheral equipment Custom stand and hopper Compactor Pneumatic or hydraulic ram SECTION IV SPECIFICATIONS BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BIO-MEDICAL AUTOCLAVE SYSTEM SPECIFICATION– EFFECTIVE SEPTIEMBRE 27, 1999 AUTOCLAVE SIZE/PROCESS THROUGHPUT FOR AUTOCLAVES NOT NEEDING SHREDDERS Units Model 100 Model 250 Model 500 Model 750 Ft. 3'5" Dia x 4' 5' Dia x 4' 5' Dia x 8' 5' Dia x 12' 5' Dia x 16' 5' Dia x 24' Meters 1.06 x 1.21 1.52 x 1.21 1.52 x 2.43 1.52 x 3.65 1.52 x 4.87 1.52 x 7.31 Lbs/cycle 100 Lbs. 250 Lbs. 500 Lbs. 750 Lbs. 1000 Lbs. 1500 Lbs. Kgs/cycle 45.3 Kgs. 113.4 Kgs. 226.8 Kgs. 340.2 Kgs. 453.6 Kgs. 680.4 Kgs. Carts 1 cart 1 cart 2 carts 3 carts Model 1000 4 carts Model 1500 5 carts FOR AUTOCLAVES NEEDING SHREDDERS Units Model 187 Model 374 Model 561 Model 750 Model 1245 Ft. 5' Dia x 3' 5' Dia x 6' 5' Dia x 9' 5' Dia x 12' 6' Dia x 13' 6' Dia x 17' Meters 1.52 x .92 1.52 x 1.83 1.52 x 2.74 1.52 x 3.65 1.83 x 3.96 1.83 x 5.18 Lbs/cycle 187 Lbs. 374 Lbs. 750 Lbs. 1245 1660 Lbs. Kgs/cycle 85 Kgs. 170 Kgs. 255 Kgs. 340.2 Kgs. 565 Kgs. 753 Kgs. Carts 1 cart 2 carts 3 carts 4 carts 4 carts 3 carts Model 1660 Cycle time: 45 minutes (load to load) BONDTECH AUTOCLAVE: Design Rating: Operating Condition: Operating Assembly: Vessel Support: Loading Arrangements: Thermal Source: Temperature/Pressure Operation Process: Blow Down: 75 PSIG & F.V. 55 PSIG/305 Deg. F./Full Vacuum Single Door/Quick Opening Door/ Safety Pin Interlock 3 Saddles Horizontal Saturated Steam 305 Deg. F./55 PSIG High vacuum/Saturated Steam/High Pressure Spray Condenser The autoclave will be designed, fabricated and tested in accordance with the ASME, Section VIII, Division 1, Boiler and Pressure Vessel Code. It will be fabricated of carbon steel plate, “pressure vessel quality” steel, well-suited to your requirements. The vessel will be designed for full vacuum. VACUUM For models 250 and 500: The vacuum will be obtained by using a steam ejector capable of pulling 24-28" Hg. The steam ejector will evacuate the vessel 24-28". For other models, we will use a specifically sized liquid ring vacuum pump capable of pulling 2428 Hg There will be a prevacuum cycle which will remove excess air from the waste load in order to allow for even steam penetration throughout the entire waste load. The air removed during the pre-vacuum process will be mixed with heated steam at 305 Deg. F. and thereafter condensed and drained into the sewer system. The post vacuum cycle removes the excess steam from the vessel and expedites the steam purging process. This process allows for a much drier end-product, and prevents excess steam from being discharged into the work area when opening the autoclave door. VESSEL DISCHARGE One properly sized spray condenser to handle the steam purge from the autoclave system will be provided. The steam will be condensed and drained to the sewer. BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] MATERIAL CONSTRUCTION Shell, Head and Door Nozzle Support Saddles Carbon Steel Pressure Vessel Grade Carbon Steel Mild Steel DOOR OPERATION, SEALING AND LOCKING MECHANISM The autoclave will be provided with a quick opening door. This is a breach lock type door that does not produce any relative motion between the door and the pressure sealing oring. The door design operates by rotating the locking ring. The door is then simply pivoted 90 degrees to allow full access. Sizing of the hydraulic components, directional control valves, hydraulic cylinders, etc. allow use of a one ½ HP hydraulic power unit for quick and efficient door operation. A hydraulic reservoir is integral with the pump unit. The door safety interlock device includes mechanical, pneumatic and electrical interlocks to prevent inadvertently opening the door under pressure. It also complies with Section UG-35 (B), (1) and (2) of the ASME Code. A limit switch and “low pressure switch” are also provided for connection into the control system for electrical interlocks as well. SUPPORTS Saddles fabricated of mild steel and welded to vessel shell. INTERNAL TRACK AND PIPING Tracks are provided at the bottom of the autoclave to match the loading/lift platform. A steam distribution manifold is internally mounted to provide com- plete steam distribution for efficient penetration coverage. CONTROL SYSTEM 1) Microprocessor control system for autoclave complete with the following features: 1) Microprocessor control system for autoclave complete with the following features: • • • • • • • • • • • • Controlled vacuum and specified Hg for programmable time period Vacuum pressure exhaust to 0 PSIG/Hg Controlled heating 0-30% Deg. F. at 099 Deg./Min. F. Run at precise temperature 0-300 Deg. F. for programmed time period Operator alerts for loading and unloading of goods Total automatic control of cycle sequence from beginning to end Operator controls for locking band and toggle pin Temperature and pressure safety back ups User friendly keypad Full program editing and storage capabilities 4 line LCD display Prepackaged in C/S Nema 12 enclosure 2) Chart Recorder •Three pen recorder, for temperature, pressure and vacuum is provided INSULATION The exterior of the autoclave will be insulated with 2" of insulation, which will then be covered with embossed aluminum. The aluminum covering is for both heat loss reduction and personnel protection. Some surfaces will not be insulated such as the door locking ring and hinge mechanism, support saddles, etc. These exposed surfaces will be painted with an industrial enamel. MATERIAL HANDLING The bins will be manually rolled in and out of the vessel. STEAM CONDENSER One properly sized spray condenser to handle the steam purge from the autoclave system will be provided. The steam will be condensed and rained into the sewer. RAMP LIFT A hydraulic ramp lift will be provided to raise one end of the track from floor level to the track level inside the autoclave. WASTE BINS Waste bins will be properly sized for each model autoclave, and we will provide enough bins for one load. Additional bins can be obtained (prices will be quoted upon request). The bins will be constructed of 3/16" aluminum plate. OPTIONAL EQUIPMENT Bin Dumper A hydraulic dumper will be provided to raise and empty the bins individually into the customer’s supplied compactor or shredder Shredders Based on the size of the autoclave, Bondtech Autoclave Systems can offer heavy-duty shredders to render the medical waste unrecognizable. Based on the requirements, we can offer single or double stage shredders. Double stage shredders are used when particle size has to be smaller. Each knife profile and configuration has been designed to suit the material for maximum throughputs and optimum shred size. Optional Features Include: •PLC Interfacing per Peripheral Equipment •Custom Stand and Hopper •Compactor •Pneumatic or Hydraulic Ram •Truck Mounted •Feed and Discharge Conveyors •Stellite hard Facing on Knives BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] SHREDDERS 1) MODEL ST-25 INDUSTRIAL SHREDDER: Cutting Chamber: 16" x 27 1/2" Drive: One 20 HP gear reduction motor, 460 Volt, 3 Phase, 60 Hertz Flange connected to shredder gearbox Two stage gear reduction Knives: Diameter: 7 3/4" Knife width: 1.130" (nominal 29mm) Shaft center distance 5" Number of teeth per knife: Two, offset hex for quick material capture. Knife material: 8620 heat-treated alloy steel Contoured cleaning fingers and hex bore spacers between knives. Fast/Slow Shaft Speed: 20.81/17.69 rpm Maximum Tooth Force: 40,485 lbs/ft Maximum Torque: 156,716 in/lbs. Support stand: 3" structural tube construction, all welded construction 38" discharge height Height to accommodate customer's discharge cart Fully welded c/w foot pad mounting Approval drawing will be supplied prior to manufacture Feed Hopper with Pneumatic Ram Assist: Includes oversized feed hopper, pneumatic ram (cam shape ram retracts out of hopper, filter Regulator, lubricator and manual direction control valve (Note: customer to supply air for ram operation - 90 psi) Hopper opening 56" x 52" approx Control Panel: NEMA 4 enclosure Keyed "power" switch Illuminated function/indicating buttons for shredder operationFused lockable disconnect All necessary fuses, contactors and thermal overloads Direct across the line starting Integral 120 volt, AC control circuit Programmable logic controller for shredder operation and monitoring Run time hour meter 2) TWO STAGE MODEL ST-25 INDUSTRIAL SHREDDER: PRIMARY REDUCTION: Cutting Chamber: 16" x 27 1/2" Two hexagonal, counter rotating shafts (2.70" across flats) False bulkhead walls at both ends of chamber to prevent migration of contaminants into bearings and seals. Drive: One 20 HP gear reduced motor, 460 Volt, 3 Phase, 60 Hertz Flange connected to shredder gearbox Two stage gear reduction Knives: Shaft center distance 5" Number of knives: 24 Knife width: 1.130" (nominal 29mm) Knife diameter: 7 3/4" Number of teeth per knife: Two offset hexes for quick material capture. Knife material: 8620 heat-treated allow steel Contoured cleaning fingers and hex bore spacers between knives Fast/SlowShaft Seed: 20.81/17.69 rpm Maximum Tooth Force: 40,485 lbs/ft Maximum Torque: 156,716 in/Lbs. Support Stand: 3" structural tube construction all welded construction 40" discharge height Height to accommodate customer's dis charge cart Fully welded c/w foot pad mounting Support primary and sharps shredders Approval drawing will be supplied prior to manufacture Feed Hopper with Pneumatic Ram Assist: Includes oversized feed hopper, pneumatic ram (cam shape) Regulator, lubricator, and manual direction control valve. (Note: Customer supply air for ram op ration - 90 psi) Hopper opening 56" x 52" approx. SECONDARY REDUCTION: Cutting Chamber: 16" x 27 1/2" Two hexagonal, counter rotating shafts (2.70" across flats) False bulkhead walls at both end of chamber to prevent migration of contaminants into bearings and seals Chamber screen, 1/2" diameter openings, laser cut, CHT-100 abrasion resistance material. BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] Knives: Shaft center distance: 5" Number of knives: 40 Knife width: .680" (nominal 17mm) Knife diameter: 7 3/4" Number of teeth per knife: two, offset hex Knife material: 8620 heat-treated allow steel Contoured cleaning fingers and hex bore spacers between knives Drive System 15 HP gear reduced motor, 460 volt, 3 phase, 60 hertz Flange connected to shredder gearbox Two stage gear reduction Fast/Slow Shaft Speed: 21.11/17.94 rpm Maximum Tooth Force: 29,930 Lbs./ft Maximum Torque: 115,858 in/Lbs. 3) MODEL ST-50 INDUSTRIAL SHREDDER: Cutting Chamber: 21" x 52" Two hexagonal, counter rotating shaft (3 3/8" across flats) False walls for added seal protection Knives: Shaft center distance: 7 1/2" Number of knives: 41 Knife width: 1 3/16" Knife diameter: 10" Number of teeth per knife: Two, offset hex for quick materials capture Knife material: 8620 heat-treated allow steel Contoured cleaning fingers and hex bore spacers between knives Support Rail System and Moving Discharge Chute Drive System: 3" structural tube construction Fully welded c/w foot pad mounting complete with "V" Groove steel castors and rail for shredder movement Shredder is moved by 4" bore, 26" stroke pneu matic cylinder Discharge and bypass infeed chutes attached and travel with shredder All required valves and piping are included Actuation is by manual control lever Control Panel NEMA 4 enclosure Keyed "power" switch Illuminated function/indicating buttons for both shredders operation Fused lockable disconnect All necessary fuses, contactors and thermal over loads Direct across the line starting Integral 120 volt, AC control circuit Integral 120 volt, AC control circuit Programmable logic controller for shredder operation and monitoring Run time hour meter Two 20 HP gear reduced motors, 460 volt, 3 phase, 60 hertz Flange connected to shredder gearbox Two stage gear reduction Fast/Slow Shaft Speed: 25.93/21.94 RPM Maximum Tooth Force: 50,538 Lbs. Maximum Torque: 252,690 in/Lbs. Support Stand: 3" structural tube construction Discharge height to suit design May be modified to suit customer's requirements Hopper with Pneumatic Ram Assist Sides enclosed for safety & to prevent spillage Hopper opening approx. 70" width (may be modified) Pneumatic ram (rectangular pusher shape), internal ram design. Filter, regulator, lubricator, and direction control valve. (Note: Customer to supply air for ram operation - 90 psi). Operation of ram is by manual push button on panel. Control Panel: NEMA 4 enclosure Keyed power switch Illuminated functions/indicating button for shredder operation Fuse lockable disconnect All necessary fuses, contactors and thermal overloads Direct across the line starting Integral 120 volt, AC control circuit Programmable logic controller for shredder operation and monitoring Run time hour meter. BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] 4) TWO STAGE MODEL ST-50 INDUSTRIAL SHREDDER: PRIMARY REDUCTION Chamber Size: 21" x 42" Drive: Two 20 HP gear reduced motor, 460 volt, 3 Phase, 60 Hertz. Knives: Diameter: 10" Number: 34 Thickness: 1 3/16" Hooks: Two per Knife Material: 8620 case hardened to 60 RC @ .060 deep Close tolerance-cleaning fingers between knives Shaft: 3 3/8" diameter, hexagonal Spherical roller bearings Hopper: Top feed opening 40" x 40" Manufactured from 3/16" mild steel plate SECONDARY REDUCTION Cutting Chamber: 21" x 42" with mating flange between primary and secondary shredders. Drive: Two 20 HP gear reducer motor, 460 volt, 3 Phase, 60 Hertz. Knives: Diameter: 10" Number: 48 Thickness: 7/8" Hooks: Three per Knife Material: 8620 case hardened to 60 RC @ .060 deep Cleaning fingers between knives Shaft: 3 3/8" Diameter, hexagonal Material: 4340 heat-treated and stress relieved Spherical roller bearings Control Panel: NEMA 12 control panel with illuminated function buttons, keyed power switch, fused lockable disconnect, starter motor with thermal overload protection and programmable logic control circuit for shredder functions including knife reversal upon overload and hour meter. Ram: Guided ram with pneumatic cylinder, manual control valve, filter, regulator, lubricator, flow control and air exhaust muffler. SELF CONTAINED COMPACTOR 2.0 Cubic yard compactor or larger and 33 to 45 cubic yard container. Liquid tight to a level of 40 inches above the container floor. Specifications: Mfg. Rating: NSWMA Rating: 2 Cubic Yards 1.52 Cubic Yards Clear Top Opening: 41" x 57.5" Performance: Cycle Time: 37 seconds Normal Force: 42,700 Lbs. Maximum Force: 50,800 Lbs. Normal Ram Face Pressure: 24.3 PSI Maximum Ram Face Pressure: 28.8 PSI Ram Penetration: 3.5" Electrical: Motor: 10 HP Control Voltage C: 120 VAC UL label all circuits, fused, key lock, start, stop and reverse Hydraulic: Pump: 10 GPM Normal Pressure: 1,800 PSI Maximum Pressure: 2,000 PSI Standard: Double end pickup 10" sump Full door seal Tri-voltage transformer Constructed of QC prime hot rolled steel Features: • Auto safety latch on door to hold it securely in place while the three-point ratchet latch mechanism is engaged. • Full door seal is mounted in a “C” channel-mounting track to prevent spillage. • A 42" x 57 1/2" large charge box allowing easily dumping of large bulky trash. • Heavy-duty rollers for easy placement of unit without causing damage to unit area. Installation: Prepackaged modular design for easy installation. LIST OF OPTIONAL EQUIPMENT Bondtech Autoclave Systems can meet your specific needs on optional equipment such as: ¨ Reusable medical waste containers ¨ Balers ¨ Self-contained compactor/container ¨ Bin Dumpers ¨ Medical waste shredders ¨ Autoclavable Bags ¨ Material Handling SECTION V AUTOCLAVE BAGS, REUSABLE CONTAINERS AND DISPOZ A FONE Bondtech’s High Heat Liners Bondtech’s high heat easy to install “PRO-TECH” liners for your autoclave carts or other high temperature lining purpose. The Bondtech “PRO-TECH” liners provide several advantages to enhance your operation. Protect your Investment! · · · · · · · Extend the life cycle of every cart utilizing the “PRO-TECH” liner. Reduce wear and tear on your dumper by dumping the treated waste easily. Enhance perception of clean/ safe operation: Maintain carts free of debris. Eliminate a potential source of nuisance odors. Eliminate labor required to periodically remove waste debris from carts. Consistent full capacity utilization—eliminating waste built-up inside carts. Reduce occupational exposure, potential injures related to cleaning waste from carts. As Easy As 1, 2 & 3 1 Simply line the empty autoclave cart 2 Deposit waste into bin and treat 3 Simply dump the treated waste Bondtech’s High Heat Liners Enhance your operation by using the Bondtech “PRO-TECH” liners. Autoclavables and Non-Autoclavables Bags Introducing “Pro-Tech Autoclavable Bags and Liners” From All High Temperature Film Is Not The Same We can uniquely custom-engineer plastic film Reduce your film cost Solve tearing, sealing and other problems Extend the life cycle of equipment by lining it. Reduce occupational exposure, potential injuries related to cleaning your equipment. Ø Autoclave bags and liners for all types of autoclaves. Ø Ø Ø Ø Ø · · · SPECIALTY PRODUCTS · Autoclavable bags and bin liners · Automotive and high temperature auto body bags · Surlyn Ionomer Film Thermoplastic polyurethane film (Dev.) · · · Bondtech’s Overview Our Manufacturing facility began production in 1973. Today, Production capacity exceeds 17 MM pounds. Our strength is our ability to produce specialty products to suit your needs. Don’t forget we provide Customer technical support at no cost Our Facility has: ¨ Six blown film lines ¨ Die diameter from 4” to 22” ¨ ISO 9002 certification in progress ¨ Lay flat tube width from 10” to 120” Mobile Home Close-off Shrink Bundling Pharmaceutical bulk containment Liquid Packaging (IBC) Printing/Laminating Skin packaging Bondtech Autoclave Systems · · · · · · · · · · · Built for Commercial Use Hydraulic Quick Opening Door PLC Controlled Pre and Post Vacuum Condenser for vented steam Strip Recorder for Pressure and Temperature Aluminum or Stainless Bins Bin Dumper Lift Table/Track System Shred-Tech Shredders Compactor and cart dumper Bondtech Treatment Technology has been supplying autoclave and shredding systems to the medical waste industry since 1983. Bondtech has designed, supplied and installed over 90 infectious waste autoclave/sterilizers for commercial and hospital applications. These large autoclaves follow all EPA and state guidelines/regulations and are accepted in all 50 states. Bondtech has manufactured autoclave systems for technical industries such as aerospace composites, glass lamination, rubber vulcanizing, wood treating, and yarn setting in addition to the sterilization of infectious waste. Contact us for more information and a facility visit, and for pricing on our autoclavable liners/bags. 2400 N. Hwy 27; 42503 TEL. (606) 677- Somerset, KY 2616 or (800) 4144231 Email: [email protected] Web: www.bondtech.net Do You Need Reuseable Medical Waste Containers? Bondtech Corporation offers you the most comprehensive line of medical waste containers. Bondtech Containers provide you with a long lasting and cost effective solution for all your hospital waste and linen handling. Let us provide you with containers for any use, whether it be medical waste, laundry collection, refuse, or recycling. Model 60002 Model 60000 28 Gal. Model 60006 115 Gal Features: Model 60010 Model 60050 · Leak Resistant · OSHA Exposure Control Plan · All sides have upper and lower handles for manual handling · Puncture Resistance Bondtech Containers are Ideal For: Hospitals, doctor’s offices, clinics, lab’s, nursing homes, funeral homes, and veterinarians Model 60045 5gal. Model 60050 3 gal. Model 60039 1.5Gal. · Fire resistant: U.L. 94HB Material High density Polyethylene · Bins and lids nest together · Conforms to: DOT HM181 Regulation · Product Liability Insurance · Dolly System Available 2400 N. Hwy 27 Somerset, KY 42503 Tel: (800) 414-4231 Fax: (606) 676-9157 Tel: (606) 676-2616 Email: [email protected] Web : www.bondtech.net Your Own Personal Phone Dispoz-A-Phone is your answer for “Throw-away” hospital telephones. These telephones are designed for use worldwide by patients in hospitals in order to address the problem of the spread of infectious diseases. Patient telephone theft has also increased the need for hospitals to purchase Dispoz-A-Phone for every room in order to reduce the capital outlays. Models: HL-288 Touch-Tone dialing with last num399V ber redial Touch-tone dialing with Hi/ normal volume Dispoz-A-Phone has several Specifications/Features: advantages: · Dynamically styled for comfortable hand· Highest Quality Telephone holding · Lowest Cost · Push-button keyboard · Immediate Delivery · Ringer shut off when you wish not to be dis· Excellent Customer Service turbed · Screen Printing (for advertising) is · Power directly from telephone line, unaffected by power failure Available · Automatic cut-off when placed on flat sur· Hearing Aid Compatible face · Available in Two Models · Wall mount holder included 1) Touch-tone with Last Number Redial · 2) Touch-tone with Hi/normal volume · FCC approved · In-use LED indicator · Mute button for privacy · 6 month Warrantee · · · · Memory redial button to recall the last number dialed Weight: Approx. 230g Dimension: 205 (L) x 57 (W) x 35 (H) mm Packing: 50 sets/carton G.W. 13.5 kgs N.W. 12.5 kgs Meas. 44.5(L) x 27(W) x 47(H) cm Don’t Forget our Deluxe Line of Dispoz-A-Phones found on the back!! Our Deluxe Line of Phones Dispoz-A-Phone is also offering a deluxe line of two-piece phones with more features. These phones are of the highest quality, hearing aid compatible, FCC & ETL approved, and carry a 6month warrantee. Models : LI82VC DP5203H Touch-Tone dialing, 3 Position volume, and Call Indicator Light Touch-Tone dialing with Hi/normal volume Dispoz-A-Phone Deluxe Phones have many advantages: · · · · · · · · · · · · Lighted Keypad Last Number Redial Visual Ringer Indicator* Mechanical bell ringer Large push button keypad 3 Position Adjustable volume control** Tone/Pulse switchable Desk or wall mountable Braille on #5 button Extra long coil and line cords Mute and Flash buttons Ringer on/off switch *Visual Indicator on Model LI82VC only **Adjustable Hi/Lo Volume on Model DP5203H Dispoz-A-Phone is perfect for: · Hospitals · Nursing Homes · College/Student Dorms · Motels and Hotels · Anywhere large number of phones are used Revenue Increases Increase your revenue by providing your patients, guests, or residents with telephone service using a quality telephone from Dispoz-A-Fone. Through different ways of charging, it is possible for patients to take home a high quality, attractive phone with a limited warranty. This will yield you a consistent income as people use your telephone services. Bondtech Corporation 2400 N. Hwy 27 Somerset, KY 42503 Tel: (800) 414-4231 Fax: (606) 676-9157 Tel: (606) 676-2616 Email: [email protected] Web : www.bondtech.net CART WASH SYSTEM FOR WASHING AND SANITIZING ALL TYPES OF MATERIAL HANDLING CARTS CONCEPT OF DESIGN BONDTECH CORPORATION The Bondtech Cart wash systems have been designed to clean and sanitize most hospital material handling carts. Important features: · Low water usage. 10 gal./cart · 2 minute cleaning cycle · Wash and rinse cycle · Force air dryer is optional · Racks can be manufactured for smaller containers · Engineered with a user friendly controller · For high volume operations we can custom design an automatic cart washer using conveyors. · Stainless steel construction for durability. · Economical to operate SPECIFICATIONS BONDTECH CORPORATION TYPES OF CART WASH SYSTEMS: · · TYPE BM—MECHANICAL CART WASH SYSTEMS TYPE BA—AUTOMOMATIC CART WASH SYSTEMS T H E C A R T W A S H S YS TE M I S A V A I L A B E I N TW O - F O U R C YC L E S . T H E C A R TS A N D / O R C O N T A I N E R S R A C K S A R E M A N I P U L A TE D W I TH A M E C H A N I C A L R O TAI N G S YS TE M . Cycle One: Direct fresh water wash with timed chemical injection system is provided. Cycle Two: Direct fresh water rinse with timed cycle. Cycle Three: a halo fog rinse with chemical injection is optional. Cycle four: A forced air dryer utilizes a turbo blower (optional) Note: The fresh water (hot or cold) is from the site’s water supply at line pressure. Waste water is discharge directly to the drain. All units are equipped with revolving spray bars. Each spray bar has multiple spray nozzles. Spray effectiveness is directly affected by the water supply line pressure and line volume. AUTOMATIC CART WASH SYSTEMS Custom-made cart system that uses a conveyor system economizing on labor and speeding the washing process. The length of the conveyor will be based on the customer’s thru-put. This type of cart wash system will be custom made. Features: 30 second wash cycle and 90 second dry cycle CONSTRUCTION: The cart wash system has the following construction features: · Heavy duty 304 stainless steel frame, sump, enclosure, panels and door grating over sump area inside enclosure ELECTRICAL REQUIREMENTS: W ATER RE QU IRE MENTS: System is available with the following electrical features: · · · 115 Volts/ 1 Phase /60 Hz for chemical injection 115 Volts/ 1 Phase/60 Hz for the electrical manipulation system and/or forced air dryer 230/460 Volts/3 Phase/60 Hz for the electrical manipulation system and/or forced air dryer. · Washer system will require the following from the site's water supply (hot or cold) · 40 psi minimum · 1” pipe water supply line SYSTEM OPTIONS W AS H E R S Y S T E M H A S T H E FOLLOW ING OPTIONS AVABILABLE: · W AT E R P R E S S U R E SYSTEM · · W AT E R H E A T I N G S Y S T E M ELECTRICAL POW ER DRIVE FOR CART MANIPULATION H A L O R I N S E W IT H C H E M I C A L INJECTION SYSTEM AIR DRY SYSTEM UTILIZING A TURBO BLOW ER AND DUCT · · BOOSTER SYSTEM PRICING BONDTECH CORPORATION CWS with wash & rinse cycles CWS with, rinse and halo fog rinse cycles CWS with wash, rinse and dry cycles Price Available Upon Receipt Of Requirements CWS with wash, rinse, halo for rinse and dry cycles Automatic Cart System Terms on standard equipment: · 50% with purchase order · 45% progress payment due after inspection & prior to shipment · 5% final payment due net 30 days from shipment Terms on Custom equipment sales: · 20% startup payment at the time of order placement · 30% payment due with approved drawings · 45% progress payment due after inspection & prior to shipment · 5% final payment due net 30 days from shipment Prices are FOB Huston fabrication facility and do not include sales taxes. Lead-time: 4-6 weeks, depending shop load and customization required. CORPORATE OFFICE STAFF BONDTECH CORPORATION ELSA BROWN PRESIDENT PH: (606) 677 2616 EXT: 225 [email protected] ANGEL AGUIAR VICE PRESIDENT PH: ( 305 ) 275 5940 (Miami, FL) [email protected] OLGA DANIELS SALES LATIN AMERICA PH: (606) 677 2616 EXT: 224 [email protected] LISA CLARK SALES PH: (606) 677 2616 EXT: 223 [email protected] 2400 N. HWY 27 SOMERSET, KY 42503 PH: (606) 677 2616 EXT: 222 (800) 414 4231 FAX (606) 676 9157 Email: [email protected] Web: www.bondtech.net SECTION VI PRICING, TERMS AND CONTRACT BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] TERMS AND CONDITIONS OF SALE 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Acceptance of Proposals: All orders are subject to acceptance by Bondtech Corporation. Home office is in Somerset, Kentucky. Price list is subject to change without notice. Changes: If, after acceptance by Bondtech Corporation, the customer desires to change the order in any way, we reserve the right to re-quote all or that portion of the order to which the change applies. Such changes will be in writing and the applicable price adjustments must be made in writing to the customer. Cancellation: If, after the acceptance of order, customer wishes to cancel same, it may be so canceled only with our written permission. In the event nonstandard parts of components are involved, we reserve the right to assess customer for any special cost resulting from such cancellation. Packaging: Any special packaging or crating requirements requested by the customer will be billed to customer. F.O.B. Points: All shipments are FOB factory, or other points of origin, when applicable. Where common carrier is utilized, shipments are made freight collect unless otherwise agreed upon beforehand. Damages: Where damage in transit is clearly established, it shall be Buyer’s responsibility to file necessary claims with originating carrier. Seller will assist and provide available information to establish and support the claim and expedite settlement. Payment Terms: 30% with purchase order – 65% prior to shipment and after inspection at factory – 5% net 30 days. Late payments shall be subject to a surcharge of one ½% per month. Shipment: 14 to 18 weeks after approval of drawings. Pricing: Prices are valid for 30 days from date of proposal. Thereafter, prices quoted herein shall be subject to escalation as a function of the SIC Code 3433 Index, published for the month in which the proposal is made, and the subsequent Index published by the U.S. Department of Labor. The percent increase, if applicable, shall be based on the Index published for the month in which the proposal is made, and the subsequent Index published for the month prior to the month equipment is shipped. Miscellaneous Fees: Federal, State or Local Taxes, Fees or Permits are not included unless specifically stated above. Permit assistance will be provided. Warranty: Current Bondtech limited warranty applies at the time of sale. Contingency: If we are prevented from carrying our provisions of our proposal due to any Acts of God, war, revolution, blockades, strikes, riot, earthquake, cyclone, labor disturbance, the operation of statues of law, interference of civil or military authority or other providential governmental or physical cause, existing or future, beyond the reasonable control of the parties, interfering with the production or receipt of goods and herein contemplated, the party so interfered with, upon prompt written notice to the other party in advance of actual shipment, shall be excused from taking or taking deliveries to the extent of such interference. BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] CONTRACT/SCOPE OF SUPPLY EQUIPMENT AND SEVICE BY CLIENT All equipment, services and materials not specifically mentioned as being supplied by Bondtech Corporation are to be furnished by client, including but not limited to the following: · · · · · · · · · · · · · · Steam supply to autoclave Drains Lighting Building and Enclosure Plant water supply to battery limits Concrete and foundation design Electric power Plant rating and permitting Temporary erections, facilities, including parking, water, toiler facilities and access to work area. All necessary building, construction and operating permits for the system proposed herein shall be by client. Compressed Air 9 CFM @ 80 PSI Natural gas (regulated) Any insulation of heat tracing duct, piping, etc. Applicable sales and used taxes BONDTECH CORPORATION By: ______________________________ Elsa J. Brown, President PURCHASER’S ACCEPTANCE: This proposal is hereby accepted by: _____________________________________________ (Signature) Company/Institution:____________________________ Name:________________________________________ Title:_________________________________________ Date:_______________________ SECTION VII PICTURES BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] JEFF ANDERSON– HOSPITAL INSTALLATIONS BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH BIOMEDICAL, AUTOCLAVE SYSTEM CAPACITY: 750/Lbs/ cycle Bondtech Autoclave System includes: Autoclave, lift table, bin dumper, Shredder, 38 cu yd compactor roll off with cart dumper BONDTECH AUTOCLAVE SYSTEM (ROOM 45 wide x 50’ Long Cart Dumper and 38 cu.yd. Compactor Roll-off Containers BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] Bondtech Biomedical Autoclave System Capacity: 750 Lbs/cycle Bondtech Autoclave System includes: Autoclave, Lift table, bin dumper Shredder, 38 cu yd compactor roll off with cart dumper Autoclaved Waste Autoclaved & Shredded Waste BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] On-Site Bio-Medical Waste Treatment System 5’ DIA X 8’ LONG BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] Commercial Bio-Medical Waste Treatment System 6’ DIA X 19’ LONG BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] COMMERCIAL BIO-MEDICAL WASTE TREATMENT SYSTEM 8’ DIA X 32 LONG BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] COMMERCIAL BIO-MEDICAL WASTE TREATMENT SYSTEM 8’ DIA X 32’ LONG BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] COMMERCIAL BIO-MEDICAL WASTE TREATMENT SYSTEM 8’ DIA X 32’ LONG BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] COMMERCIAL BIO-MEDICAL WASTE TREATMENT SYSTEM 8’ DIA X 32’ LONG BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] ON-SIDE SYSTEM INSTALLATION PHASE BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] Bondtech Treatment Technology 2 Model 500 Autoclave with carts, lift table, Cart dumper and 2 stage shedder BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] Bondtech Treatment Technology Model 750 Autoclave with carts, lift table, Cart dumper and 2 stage shredder BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] COMMERCIAL BIO-MEDICAL WASTE TREATMENT SYSTEM 7’ DIA X 26’ LONG SECTION VIII BROCHURES BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected] BONDTECH CORPORATION 2400 N. Highway 27 Somerset, KY 42503 Phone: 800-414-4231 Phone: 606-677-2616 Fax: 606-676-9157 Email: [email protected]
