QA Binder Documents Contractor`s Introductory Package

Transcription

TRIARCH ARCHITECTURAL FINISHES
Contractor’s introductory package








Duroplex®
Duroplex® Designer
Series
Plexture®
Granyte™
Collection of Joy™
Klondike®
Venetian Plaster
Performance architectural plasters,
decorative specialty paints and
seamless stone veneers
 Abrasion resistance
 Impact resistance
 Washable
 Non-fading
 Meets LEED criteria
Thank you for your interest in our materials. Triarch manufactures and supplies an expanding
line of specialty paint and plaster materials to contractors around the world.
We strive to be best in class in each product category we supply. We deliver a
high level of support with our products, wanting your company to excel in the
application of our materials. It is our intention to make you a life long customer
consistent with good business practices. Our products range from simple-touse products off the shelf, to products that require a training class before we
will sell you product. Please refer to the listing below of products that require
training and those that do not. We look forward to earning your business and
working with you.—BRUCE WINGATE, GENERAL MANAGER
Products that require a training:





A training class at our training center in Rhode Island
Duroplex
Plexture
Granyte
Spatula Stuhhi Venetian Plaster
Faulux
Product that do not require training*:
Klondike
Klondike Light
Collection of Joy



* Remote application support is available
through videos, illustrated application
guides and telephone.
Training Class at a Customer Facility
We currently have approximately 30 sales representatives nationally promoting our products to architects,
interior designers and end users. After successful completion of the training session, your firm's name will be
placed on our list of approved installers. From time to time, our reps will advise your company of projects
where are products are listed in the specifications. Sometimes these will be negotiated projects, sometimes
they will be open bid projects. Almost all of the currently trained contractors find the installation of our products to be profitable work, as well as an opportunity to expand into the specialty
finishes market - the fastest growing segment of the paint and coatings industry.
Company History
Triarch’s Duroplex® system, first entered the market in 1985. Over the years, the product line expanded to include a
wide range of decorative and performance products such as Plexture®, SKIMM™, and FRESCO™ coatings. In 2003,
Triarch was acquired by Dryvit Systems, Inc., the North American leader in exterior insulated wall systems. The acquisition caused the company to relocate from Houston, Texas to the current headquarters in West Warwick, Rhode
Island. Triarch materials are produced in ISO 9001 & 14001 certified facilities.
Products
Today, Triarch operates as a division of Dryvit Systems
Inc. offering a wide range of architectural paints and
coatings for the interior and the exterior of commercial
and residential buildings. Examples of various projects can
be found under NOTABLE PROJECTS. Please refer to
our website under PRODUCTS for a detailed listing and
product technical data. All Triarch products conform to
sustainable building protocols as detailed in LEED and
Green Seal Indoor Air Quality documentation.













Duroplex®
Duroplex® Dimensional Metals
Plexture ®
Granyte™
Spatula Stuhhi® Venetian Plasters
Klondike® & Klondike® Light specialty
paints
Faulux™
Acrylic Glaze™
PolyGlaz®
SKIMM™
REFORMIT™
RAC™ anti-cracking mesh
Environmental
ISO 14000 outlines a systematic approach to environmental management. It provides practical tools for organizations
looking to identify and control their environmental impacts. We constantly seek to improve our environmental performance through well defined objectives and measurement metrics. All four Triarch locations are ISO 14001 certified. On our website, under key word SUSTAINABILITY, we identify the following areas of focus:



Produce products that comply with sustainable building practices
A corporate commitment to the way we operate and view the world
Our manufacturing processes with regard to reducing our use of energy, water, waste disposal; we seek
year over year improvements. We control our noise generation, our dust emissions and have an active
recycling program that encourages employee participation at all levels. We use third party services to validate of our products, process and systems
Our Service Commitments
 Return all calls and emails promptly, if possible the same day
 Resolve problems head on, do what is fair to resolve problems and move on
 Stand by our quotes and stand behind our products
We welcome additional questions and interest regarding our products and our company. The next page provides additional information on our sampling, materials installation, our manufacturing locations and sustainability.
Please
contact me if we may be of service.
Sincerely,
Bruce R. Wingate
Bruce R. Wingate
Vice President & General Manager
www.triarchinc.com
Phone: 800-537-6111
How we do it
Samples
Installation
Triarch provides standard and custom colored samples
for projects. In many cases, samples using our standard
colors and patterns are on our inventory shelves and
may be shipped promptly. Custom colors and custom
patterns may take up to 10 days to fabricate and ship.
Projects using below 1000 square feet of product may
have a small sample charge. Certain products have custom color limitations. Visit our website for images of completed projects. Speak with our sales representatives for
catalogs and additional information.
Triarch supplies our paint and plaster products to leading
decorative painting contractors. We conduct product
application sessions for installation contractors every
month. See our website under the navigation tab CONTRACTORS for more details. We supply a contractor
referral list of trained contractors by specific markets.
Call CUSTOMER SERVICE at 800-537-6111 for contractors near your project. Certain products, such as
KLONDIKE® and Collection of Joy™ may be easily applied by anyone with basic painting skills and does not
require a trained contractor.
Supply
Sustainability
Triarch supplies our paint and plaster products to global
markets from our four ISO certified plants around the
country. This means delivery times are short and freight
cost is kept to a minimum. Shown above are the 500 hundred mile radius from each of plants that would allow our
materials to meet LEED Regional Material credit 5.1.
Please check our website for the latest information on our
sustainable products and practices.
Advance preparation for a product application training class
Thank you for your interest in our materials. Our training class is typically (1) day per
product, although some products may be understood in less time. The goal of the class
is to impart the basic skills and knowledge behind the application of our materials. The
class will not make you an expert1, as it is only a one day program, but it should provide
you the knowledge to enable you to practice and refine your newly acquired skills.
Typically there are materials left over from the class that you may keep and use for
practice. We supplement the training session with manuals, videos, and samples for
your reference.
This class is for experienced painters and finish plasters. The class is not for individuals
learning to paint, or for apprentices with minimum paint application skills. We will teach
different ways to use paint & plaster skills as it relates to our materials, but a solid
background in application techniques, substrate differences, primers, working with
applied color, spray guns and masking techniques is both expected and necessary.
Listed below are approximate training times. Class size and previous experience of the
attendees will affect the speed of the class:





Duroplex – (1) day
Plexture – ½ day
Granyte – ½ day
Sand Storm – ½ day
Spatula Stuhhi – 2 days MINIMUM
Things you will need to have set up and ready for the training in advance of our arrival.
Duroplex and Plexture training class:
 A square drywall mixing paddle and variable speed electric drill.
 Drywall surface. Provide at least eight (8) 4x8 gypsum boards (256 sqft/23 m2). Four
(4) need to be firmly mounted to a wall or vertical frame. The floor should be
covered with a drop cloth, plastic or paper.
 A freewheeling roller frame and a 3/8” nap roller cover with extension pole.
 An air compressor with regulator and hose.
 If a Plexture class, you will need an airless spray rig.
 Plastic spray bottle with adjustable nozzle to spray water.
 Clean rags
 A block sponge
 Four 5-gal pails of clean water.
 Training materials we have shipped to you. This should arrive 1- 2 days prior to the
training.
1
Practice is required before your work will be commercially viable
Page | 1
Advance preparation for a product application training class
If Granyte products are the focus of the training, then:
 (2) 4’ X 8’ pieces of drywall hung horizontally on a wall. Typically, this sheet
would be about 2 ft. off the ground and extend to 6 ft. high.
 A piece of tape can be used to separate the sheet in two and one side can be
used to demo and one side can be used for practice.
 These products mix up differently…the best way is a B-MEW mixer from
Windlock.
 T-PFTAN float (Windlock) for the Granyte just to show another application
technique for that product.
 A roller frame and ½” knap roller sleeve for the colored Primer.
 A stainless steel plastering trowel is also required along with a hawk and margin
trowel.
If Spatula Stuhhi products are the focus of the training, then:




A roller frame and ½” knap roller sleeve for the GEXXO Primer.
Trowels provided with the training materials
Cotton rags for waxing
Drywall surface. Provide at least eight (8) 4x8 gypsum boards (256 sqft/23 m2).
Four (4) need to be firmly mounted to a wall or vertical frame. The floor should
be covered with a drop cloth, plastic or paper.
 Training materials provided by us
Typically we do not provide a formal training class for some of our other products, such
as Klondike and Collection of Joy. However we would be pleased to review them with
you during class time, but we will need to know your intentions in advance so we can
have materials prepared to demonstrate properly.
Thank you. We look forward to meeting you and a fun day.
Page | 2
Dear Prospective Customer;
QA Cover Letter and Qualifications
Thank you for your inquiry into our product line(s). As described to you over the phone, we provide a training
program on a number of our products including Duroplex® and Plexture®. We find that this approach helps improve
quality control, reduces costly application errors, and potentially increases your profits. Basically, this program
consists of 2 short and easy steps:
1. Complete and return the attached application, which includes the appropriate data for us to run a
credit check, so we can consider opening a trade account for you. Be sure to sign page 03 of the
application and return it to us.
2. After our acceptance of your application, we will coordinate with you to schedule a training program
for your people. This training will take place at your facilities, or at our training center in Rhode Island.
After successful completion of the training session, your firm's name will be placed on our list of approved
applicators. Then, our Sales Representatives will, from time to time, bring jobs to your firm in which there will be
limited competition. We currently have approximately 30 Reps nationally. Almost all of the currently trained
contractors find our products to be profitable work, as well as an opportunity to expand into the specialty finishes
market - the fastest growing segment of the paint and coatings industry.
To begin this new and rewarding association, simply complete and return the attached application. The
combination application and the credit check form helps us to quickly respond to your needs and evaluate your
firm's ability to handle our product. Pricing will not be released until we have received a completed application.
Note: In certain areas of the country, pricing will not be released until training is completed.
As far as the cost associated with the training, we try to minimize your cost through careful planning. We will
provide you a hard number so that you will know in advance what the training cost will be.
We look forward to working with your firm on this project as well as future work. Very shortly after we receive the
completed forms, we will contact you with the training cost options available to you. Once we have agreed on cost,
a training date will be scheduled and we will send you a confirmation letter along with the training date. At the
training, we will provide you with instructions, videotapes, specialized tools, and written support materials. Should
you have any questions or concerns, please call us on our
toll free line: 1.800.537.6111.
Thank you,
Henry Severino
Henry Severino, ext: 1290
Customer Service Manager
Page | 1
QA Cover Letter and Qualifications
QUALIFICATIONS FOR BECOMING
A QUALIFIED APPLICATOR [QDA™ OR QPA™] COMPANY
___________________________________________________________________________
DUROPLEX®: (QDA)
TYPE OF BUSINESS: The applicant company must have been in the paint contracting business [wet goods
application] for at least the last three (3) consecutive years.
STABILITY OF CREW: Applicant company must have at least one (1) full time regular supervisory employee
meeting the following requirements:
1.
Must have been employed with applicant company for at least three (3) consecutive years as a painter
or painting supervisor.
2.
Must be skilled in the painting trades since our training class covers material application and does not
cover basic painting skills.
_______________________________________________________________________
PLEXTURE®: (QPA)
TYPE OF BUSINESS: In the construction trade & familiar with wall finishing techniques
STABILITY OF CREW: Applicant company must have at least one (1) full time regular supervisory employee
meeting the following requirements:
1.
2.
Must have been employed with applicant company for at least one (1) year.
Must be skilled in the painting trades since our training class covers material application and does not
cover basic painting skills. Familiarity with spray equipment is required.
________________________________________________________________________
SOUND FINANCIAL CONDITION: Applicant company must have a current sound financial condition, have a
recent record of timely payments to trade accounts, and have no current unpaid tax liens, judgements, or other
impairments to applicant's financial standing. TRIARCH reserves the right to determine the acceptability of
applicant's financial condition. NOTE: Applicant's financial condition must be sound regardless if applicant does
not request credit terms with the company.
PROVIDE ALL OF THE INFORMATION: Applicant company is requested to provide all information requested;
otherwise, delays in processing the application may result. Please submit the completed forms and sign the
Credit Application/Agreement.
APPLICATION TRAINING: Applicant company will be trained by a TRIARCH factory Field Operations'
representative. Upon successful completion of the training class, the Applicant will be considered as a Qualified
Applicator of the particular product line and listed on TRIARCH's Approved Applicator List.
QUALIFICATION MAY BE LOST IF:
1.
The personnel trained by TRIARCH leave the Applicator's employ.
2.
Non-payment or consistent late payments on trade account.
3.
Product(s) are not applied according to Triarch specifications and recommendations.
4.
The Applicator sells or provides unapplied (wet) materials to non-factory qualified contractors.
5.
Applicator transfers the knowledge, literature, or instructions of TRIARCH to a competitor of TRIARCH.
Page | 2
Qualified Installer Application
INSTRUCTIONS: Complete all requested information. Read and sign Page 3 & the "QUALIFIED
INSTALLER AGREEMENT" (attached). Fax all pages of the completed documents to (401) 822-2984.
Email: [email protected]
CREDIT DATA
TODAY'S DATE:
/
/
Company Name:
Street Address:
Billing Address:
(IF DIFFERENT FROM STREET ADDRESS)
Email Address:
City:
County:
Phone Number:
ST:
Zip:
FAX Number:
Type of Business:
Business Structure?
Corporation
Partnership
Proprietorship ____
Key Contacts:
President:
Email Address:
Chief Estimator:
Email Address:
What year was your business established? ___________
Is your business a division of another firm? YES 
NO 
If yes, what is the parent company's name and address?
Annual Business Volume: 2011
, 2012
, 2013 __________.
YES 
NO 
Average number of Employees on your payroll:
Union
Does your firm use purchase orders?
Field Operations Manager's Name:
What % of your business is: Commercial
Residential
Do you have a State Contractor's License: YES  Please provide the number:
NO 
Page | 1
Non-Union
Industrial
What trades are represented by your firm?
.,
___________________________________________
General Geographic Area Covered:
PAINT TRADE CREDIT REFERENCES:
Company name:
Acct #
Location:
Phone #
Company name:
Acct #
Location:
Phone #
Company name:
Acct #
Location:
Phone #
Tell us about some of projects that you are proud of:
PROJECT REFERENCES:
#1: Type of Project
Contact Name:
Phone#:
#2: Type of Project
Contact Name:
Phone#:
#3: Type of Project
Contact Name:
Phone#:
In order to provide the best training experience:
What products do you wish to train your firm in: (circle the appropriate products)
Duroplex
Plexture
Spatula Stuhhi
Granyte
Who are the crew members that will be trained to install TRIARCH products?
Foreman:
Yrs w/Co.
Email Address
Crewman:
Yrs w/Co.
Email Address
Crewman:
Yrs w/Co.
Email Address
Page | 2
____________
What specialty paints or coatings have you installed or distributed?
Product Name
Manufacturer's Name
_________________________
_________________________
I understand the information I am furnishing is for the purpose of establishing our
qualifications to become an authorized installer of products manufactured by TRIARCH
Industries, Inc. I also understand that I am granting TRIARCH authorization to contact
any of my references provided and to research my credit history.
I recognize that all amounts due and payable to TRIARCH are payable within thirty (30)
calendar days of material shipment to my designated location, and that materials are not
returnable. I agree that if payment is not received by TRIARCH within thirty (30) days of
shipment, TRIARCH is hereby authorized to charge the outstanding balance to my credit
card. A fully executed Credit Card Authorization form is attached. I understand that past
due amounts shall accrue late payment charges of 18% per annum and that any and all
costs incurred in collecting past due amounts shall be added to the amount due. I agree to
pay for all associated collection costs in addition to the amounts due.
FIRM NAME: _________________________________________________
SIGNATURE
DATE
TITLE
PRINTED NAME
If you have any questions regarding this application, please call TRIARCH Industries, Inc.
@.800.537.6111. Please allow 5-10 working days for processing.
Before returning this form:
Did you complete all of the questions?
Did you sign the application on page 3?
Did you sign the attached Qualified Agreement(s)?
Thank you for your interest.
We look forward to working with you!
Page | 3
QUALIFIED APPLICATOR AGREEMENT
DUROPLEX, PLEXTURE and/or Spatula Stuhhi
Page 01 of 04
COMPANY
(Qualified Applicator/Installer)
ADDRESS
In consideration of the opportunities and privileges granted by Triarch to Qualified
Applicator [Installer] of its products, Installer and Triarch agree thus:
Triarch appoints Installer as a Factory Qualified Applicator {QA} of products, but Triarch does not certify
Applicator's ability for any particular job. Applicator/Installer agrees to install all products in accordance
with the factory specifications, instructions, and recommendations in effect at the time of application.
•
•
•
Installer agrees to install all products utilizing Triarch factory trained personnel or skilled
personnel operating under the direct supervision of a Triarch factory trained supervisor
employed by Qualified Applicator.
Installer agrees to pay Triarch for purchased materials in accordance with Triarch's written
conditions of sale and credit terms by check or credit card. Triarch’s CONDITIONS OF
SALE are made a part of this AGREEMENT.
It is expressly understood that unapplied materials (i.e. wet materials) purchased from Triarch
by Installer may not be sold by Installer to any Third Party without Triarch's written consent.
This requirement shall not preclude Installer from leaving materials on a completed job for
customer's use as may be required by contractual specifications.
Use of Documentation and Product Names:
•
•
Page | 4
It is expressly understood that Triarch grants to Installer a perpetual license to use the
documentation provided by Triarch within the confines of the Qualified Company, provided
QA is a customer in good standing with Triarch. Any distribution or duplication of data to
third party firms is expressly prohibited and may result in a revocation by Triarch of the
Installer listed as "qualified".
Triarch grants to the Applicator a limited license for the use of Triarch’s product tradenames
on the Internet and on Applicator’s business cards, only as long as Applicator is a customer in
good standing with Triarch. In the event of Triarch removing the Qualified Applicator status,
QA will immediately remove any and all references to Triarch products by the QA from the
Internet and from any or all printed references. Removal of Triarch’s product names from
QA’s website, Internet search engines, and printed materials, shall be at the sole expense of
the QA.
QUALIFIED INSTALLER AGREEMENT
DUROPLEX and/or PLEXTURE
Page 02 of 04
Warranty by Qualified Applicator
Triarch warrants materials in accordance with Triarch's written Limited Warranty. Notwithstanding the
foregoing, Triarch's warranty is contingent upon Installer applying said materials in accordance with
Triarch's written specifications, instructions, and recommendations. Installer shall notify Triarch
immediately (prior to installation) of any apparent defect in materials. Triarch agrees to replace any
defective materials as soon as possible at no charge to Installer provided that defective materials are
returned to Triarch if requested by Triarch. As a condition of this agreement, Installer warrants the
installation {labor only} for a period of one-year following completion of each job. If materials are not
installed in accordance with Triarch's written specifications, instructions, and recommendations, Installer
agrees to provide the full warranty for both materials and labor.
In the event that Installer fails to conform to the terms and conditions of the agreement, Triarch may
withdraw this appointment. Installer may resign from this qualification at any time. The foregoing
notwithstanding, all terms and conditions pertaining to materials already sold and/or applied by Installer at
the time of dissolution of this Agreement, will remain in full force and effect for the warranty periods.
CONDITIONS OF SALE
Current as of March 31, 2011
Made a part of all Materials Orders and the Qualified Installer Agreement
CONDITIONS OF SALE are made a part of all MATERIAL ORDERS and the QUALIFIED ISTALLER
AGREEMENT.
1. PLACEMENT OF ORDERS. All orders shall be placed at the Triarch designated office and at all times are subject
to acceptance by Triarch (Seller).
2. CREDIT. Each delivery of material is subject to cash or to credit arrangements made by Buyer with Seller. If Buyer
does not comply with such terms, or if Seller believes Buyer’s credit standing is impaired, Seller may withhold
deliveries, or place a lien on the real estate. In the case of future deliveries, Seller may withhold deliveries until buyer
makes satisfactory cash or credit arrangements for payment of all
outstanding balances. If goods have already been delivered, Seller may withhold all future deliveries until Buyer makes
satisfactory security arrangements for payment of all outstanding balances. If Buyer fails to make cash or credit
arrangements satisfactory to Seller, or to comply with such arrangements, Seller may demand in writing that Buyer
provide written assurances that Buyer is able to make payments under the terms of this contract. If Buyer does not
provide assurances acceptable to Seller within 10 days of receiving Seller’s demand, Seller may terminate the contract
without liability and without waiving any other
remedies if may have against Buyer. Seller may also process and perfect any liens or bond claims against the subject
property according to local law.
3. TITLE AND RISK OF LOSS. All shipments are made under INCO terms: CPT (Carriage Paid to).
Seller does not accept any costs associated with unloading of materials. Any and all importation costs, including but not
limited to storage, VAT, certifications, translations, and tax stamps are for the account of the buyer.
4. GENERAL WARRANTIES OF SELLER. Seller warrants that (a) all material supplied under this contract will
conform to the description stated on the front side hereof, or to written product specifications and warranties published
by Seller; and (b) upon payment of the purchase price, Buyer will receive good title to all such material free from any
liens, encumbrances, or lawful security interests. Except for the foregoing warranties, SELLER MAKES NO OTHER
WARRANTIES EXPRESSED OR IMPLIED. SELLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Seller, upon request, may furnish to
Buyer such technical advice, as it may be able to supply with reference to the use by Buyer of any material delivered
hereunder. Seller, however, assumes no obligation or liability for the advice given or the results obtained. Buyer agrees
to fully determine the suitability of Seller’s material in Buyer’s applications prior to adopting them on a commercial
scale.
Page | 5
Page 03 of 04
5. MATERIAL SAFETY DATA SHEET: Seller will make available to Buyer through Triarch website a material safety
data sheet with information concerning the material and precautions to be taken in the material’s storage and handling.
Buyer shall be responsible for knowing all such information and precautions disclosed in the material safety data sheet,
and for conveying such information to persons who may be exposed to the material.
6. INSPECTION: Promptly upon receipt of all materials delivered under this contract, Buyer shall inspect such
materials for any damage, defect or shortage. All claims for shortage or non-delivery and any claim for damage or
defect which would reasonably be discoverable in the course of such investigation shall be waived unless Buyer
notifies Seller in writing days two (2) business days after receiving the materials to which the claim relates. Digital
photos with a date stamp are strongly suggested.
7. LIMITATION OF REMEDY: Buyer’s exclusive remedy against Seller for any claim hereunder shall be, at Seller’s
option, either (a) recovery of a dollar amount which does not exceed the purchase price of the materials the claim
relates to; or (b) replacement of the materials. The remedy provided in the proceeding sentence shall be Buyer’s
exclusive remedy, regardless of whether Buyer’s claim is in contract, tort (including negligence or gross negligence,
whether sole or concurrent), or otherwise, so long as the
claim arises in connection with this contact. In no event shall Seller be liable for special, indirect, incidental or
consequential damages arising out of this transaction, including without limitation lost profits, environmental damages
and attorneys’ fees. No custom materials may be returned to Seller. No standard materials may be returned to Seller
without Seller’s consent, and then subject to a restocking fee. Transportation charges for the return of materials shall be
the expense of the Buyer. Buyer
understands and agrees that Seller has no control over the use of any materials sold under this contract. Moreover, the
value of materials sold under this contract may be substantially less than the value of final products in which Buyer
uses such materials. Therefore, Buyer bears all responsibility for, and agrees to indemnify, defend and hold Seller
harmless from all liability and costs associated with (a) the handling, possession, use or disposal of such materials; and
(b) the performance or resale of any of Buyer’s products made from any of such materials. The provisions of this
paragraph shall survive the termination of this contract.
8. FORCE MAJEURE: Either party may reduce or suspend deliveries in the event if labor trouble, strike, lockout, or
injunction, or upon any event beyond the reasonable control of such party (including without limitation shortage of any
raw material or intermediate upon which the manufacture of the material is dependant), provided such event makes it
impracticable, to manufacture, transport, accept or use a shipment of the material. If it is impracticable for Seller to
supply the total demand for the material because of such an event, Seller may allocate its available supply of the
material among itself and its customers in a
manner it determines to be equitable. During such an allocation, Seller will not be obligated to purchase material from
other sources to satisfy its obligations under this contract. Either party may suspend deliveries under this paragraph
without liability, but this contract shall otherwise remain in effect. If deliveries are suspended due to force majeure for
thirty (30) consecutive days, either party may cancel this contract upon 30 days written notice.
9. DURATION OF PRICES & RETURNS: Material and sundry prices quoted herein shall be good for ninety
(90) days from date of order. Triarch reserves the right to adjust any invoice for clerical and math errors. Freight
costs are provided as a good faith estimate and are subject to change without notice. RETURN OF MATERIAL
is subject to the then current return policy and will be subject to a restocking charge and return freight costs are
the burden of the customer. However custom colored materials may not be returned.
10. GOVERNING LAW: The parties agree to exclude the application of the U.N. Convention on Contracts for the
International Sales of Goods, 1980. The parties also agree this contract shall be governed by the domestic law of the
State of Rhode Island, except with respect to its choice of law provisions.
11. ARBITRATION OF DISPUTES: Any controversy or claim arising out of this contract or the breach thereof may, at
Seller’s option, be referred to non-binding mediation under rules of Seller’s choice. If mediation does not result in
settlement of the dispute, (or if Seller does not elect to pursue mediation), Seller shall have the right to refer the dispute
to binding arbitration under rules of its choice, or to commence litigation.
12. WAIVER: Either party’s failure to insist upon strict performance of any of the terms of this contract will not be
construed as a waiver or relinquishment, to any extent, of the right to assert or rely upon such terms, or any other terms,
on any future occasion.
13. SEVERABILITY: The invalidity of any provision of this contract will not affect the validity of the remaining
provisions, and this contract will be construed as if the invalid provision has been omitted.
Page | 6
Page 04 of 04
14 ENTIRE AGREEMENT MODIFICATION: This contract, including any Triarch Order Form and Qualified Installer
Agreement, and any attachments, constitutes the full understanding of the parties and is a complete and exclusive
agreement. If there is a conflict between the printed terms and conditions of this
statement of the terms of their
form and the terms and conditions on the reverse side or any attachment, the terms and conditions on the reverse side or
on the attached will govern. Any modification of this contract or waiver to its terms must be made in writing and signed
by the party claimed to be bound by the modification. No
modification of this contract shall be effected by the acknowledgment or acceptance of purchase orders, shipping
instruction forms, or any other documents containing terms or conditions different from or in addition to those in this
contract, all such different or additional terms being hereby objected to: BY ORDERING FOR SHIPMENT ANY
MATERIAL UNDER THIS CONTRACT, BUYER AGREES TO ALL THE TERMS AND CONDITIONS
CONTAINED HEREIN.
INSTALLER:
________________________________________
(Signature)
TRIARCH
_______________________________________
(Signature)
TITLE: __________________________________ TITLE:________________________________
DATE: __________________________________
QA Consolidated Document.doc
February 4, 2014
Page | 7
DATE:_________________________________
“Noble life demands a noble
architecture for noble uses of noble
men. Lack of culture means what it
has always meant: ignoble civilization
and therefore imminent downfall.
Spray Pattern DS III
Frank Lloyd Wright
Flagstone DS II
T1220
Ancient Stone DSII
Maximum longevity, abuse resistance and low maintenance costs. Duroplex offers performance & aesthetics with design freedom.
Duroplex® has been a national and international market leader
for interior performance textures for more than 20 years.
Duroplex has been chemically engineered to have a low carbon
footprint and meets low VOC criteria for both LEED (IEQ 4.2)
and Green Seal. It provides maximum longevity, abuse
resistance and resistance against mold or mildew. The
advantages of Duroplex over traditional wall covering or other
materials with a similar appearance make it the logical
economic and aesthetic choice. It is backed by a ten (10) year
warranty against surface mold or mildew growth and cracking
or delamination. It is also 80% as hard as mild steel,
noncombustible, integral & colorfast pigmentation and is
breathable at 28 perms. Duroplex improves the abuse
resistance of drywall and impact resistant boards. See our
website for more information on abuse resistance and other
performance related features. Two hundred eighty-eight
standard colors and 25 established textures or patterns, plus
broad custom capabilities in both texture and color round out
the product line for uncompromising value.
Tuscany DS II
Eilan Hotel, San Antonio, TX
Antiqua DS II
Delta Crown Room, Seatac Airport, Seattle, WA
DUROPLEX
PERFORMANCE FEATURES
• 288 standard colors as well as custom colors
• Color Options: Monochromatic, multi-color blends,
metallic glazes (DDM2)
• Integral color and colorfast
• Washable
• Abrasion resistance – over 8000 scrub cycles
• 80% as hard as mild steel*
* Surface abrasion, Indentation, and soft body impact testing under ASTM C 1629
• Breathable – perm rate of 28
• Class “A” – noncombustible
• Typically installed $1.25 – $3/sqft*
• Low VOC USGBC LEED 4.2 compliant
• 10-year limited material warranty
• 10-year limited material warranty against surface
mold or mildew growth ASTM D 3273
• Most finishes easily patched
* Based upon 10,000 sqft, 9’ ceiling height and average labor rate
of $25/hr.
www.triarchinc.com
800-537-6111
Printed in USA R3:08-20-12
©Triarch 2010
Duroplex®
T102
High Performance Seamless Interior Coating System
CHARACTERISTICS
• An interior, high solids, one
part water based decorative
acrylic coating.
• Designed to improve the
abrasion and impact
resistance of drywall.
• Applies directly to most
common substrates.
• Class “A” non-combustible,
non-toxic, very low VOC.
• Exceptional performance
against mold and mildew
growth.
• Non-fading, very high UV
resistance.
• Use in lieu of vinyl wall
covering.
• Surface hardness 80% as
hard as mild steel.
• Improves the strength of
drywall.
• Significantly longer life
cycle than vinyl wall
covering.
10-YEAR WRITTEN
PERFORMANCE WARRANTY
Against fading, peeling,
delaminating, cracking, and
chalking.
10-YEAR WRITTEN
MOLD/MILDEW WARRANTY
•
•
•
High perm rate to achieve
breathability.
Engineered formulation
which virtually eliminates
food sources for organisms
combined with a long-term
mildewcide that provides
excellent performance.
Full details available by
contacting Triarch.
Printed in USA R:2 04/24/2013
©Triarch 2008
SCRUBBABLE
• Not damaged by water.
• Most marks and scuffs
removed after 7 – 10 days of
curing, using a stiff scrub
brush with liquid soap and
water.
DESIGN OPTIONS
• Actual job conditions,
volume, wall elevations, and
local labor may affect
installed prices.
PRODUCT DATA
SPECIFICATIONS
• Water based acrylic
• Over twenty-five (25)
textural effect/patterns and
almost unlimited integral
colors, both monochromatic
and multi-color finishes.
• Metallic Glazes
• Old World Stain™
• PolyGlaz® optional clear
coat provides a sealed
surface for healthcare and
food service installations.
• Call TRIARCH for samples
or a design binder.
• Integral & Colorfast
Pigments
DELIVERY TIME
• ASTM D 4977 Surface
Abrasion = Class 3 over 5/8”
drywall
Regional manufacturing from
four ISO certified plants. Most
orders delivered within 5 days.
FACTORY TRAINED
APPLICATORS*
• Over 600 factory trained
applicators available
nationally and
internationally.
• We offer training programs
to help insure quality control
and minimize installation
time.
COST
• Most projects install from
$1.25 - $4.00 per square
foot.
• Barcol Hardness of 38
• ASTM E-84, flame & smoke
Class A
• FAR 25.853(b), FAA Vertical
Burn Test, after flame time
<0.1 seconds
• ASTM E-96, English Wet
Perms = 28
• ASTM D3273-00 Surface
Mold Resistance = 10 (no
growth)
• ASTM D 5420 Gardner
Impact = Class 3 over
Impact resistant wallboard
• Final dry film thickness of 20
mils
• Qualifies under LEEDS
section 4.2 for low emitting
material
• Conforms to CHPS-CA
section 01350
APPLICATION
Applied by factory trained
installers. Texture roller or
texture spray applied
depending. Many patterns
require additional
finishing techniques.
Duroplex®
T102
High Performance Seamless Interior Coating System
page 2
STORAGE & SHIPPING
• Shipped in 5 gallon plastic
pails.
• Protect from freezing.
• Protect from heat over
100°F.
• Stack to maximum of three
pails high.
• Two (2) year shelf life.
RELATED DOCUMENTS
• T302 Guide Specifications
• T1210 Test and
Sustainability
• T1220 Web brochure
• StratoTone™ High
Performance
Color Charts
• T202 MSDS
• T121 PolyGlaz Clear Sealer
• Product Videos on website
Printed in USA R:2 04/24/2013
©Triarch 2008
Duroplex®- EXT
T105
High Performance Seamless Exterior Coating
•
DESCRIPTION
•
•
•
An exterior, high solids, one
part water based acrylic
coating, designed to deliver
high performance results at
a moderate price.
Perfect coating for
shopping centers, schools,
office buildings, etc.
Also provides different
performance characteristics
and traits than interior
Duroplex® coating.
Call TRIARCH for samples,
color charts, or a design
binder.
Burn. After Flame Time
<0.1 seconds
DELIVERY TIME
Dry film thickness of 20 mils
Most orders leave the centrally
located factory within 2-3 days.
SHIPPING AND STORAGE
FACTORY TRAINED
APPLICATORS*
Over 600 factory trained
applicators available nationally
and internationally.*
pails
• Protect from freezing
100°F.
• One (1) year shelf life
ADVANTAGES
NO SPECIAL SUBSTRATE
NEEDED
Applies to all clean, sound,
unpainted concrete and
masonry type substrates (not
for use with sheet goods)
5-YEAR LIMITED MATERIALS
WARRANTY
COST
APPLICATION
Most projects install from $1.50
- $3.00 per square foot. Actual
job conditions, volume, wall
elevations, and local labor may
affect installed prices.
Wet, color tinted in 5 gallon
pails. Install per application
instructions.
PRODUCT DATA
• Base coat and/or texture
applied 25-35 mils thick, wet
mils
SPECIFICATIONS
Against peeling, delaminating,
cracking, and chalking.
• Integral & colorfast pigments
DESIGN OPTIONS
• Most unique finishes in the
industry.
• Over fifteen (15) textural
effect/patterns and almost
unlimited integral colors,
both monochromatic and
multi-color finishes.
• 1000hr. QUV Weather
Simulation Test
• Ultraviolet, wet/dry, heat/chill
no failures
• Flame: Class A
ASTM E-84, Flame spread =
8.5, smoke contribution =
6.5
FINISH
• Final minimum required film
thickness shall be 20 mils
for warranty purposes.
• Finish may be roller, spray,
or tool applied depending
upon desired finish effect.
WARRANTY
Triarch offers a five (5) year
written Duroplex-Ext warranty.
Contact Triarch for details.
*TRIARCH DOES NOT WARRANT, GUARANTEE, OR ASSUME LIABILITY FOR THE WORKMANSHIP OF THE APPLICATOR.
Triarch
P.O. Box 1014
One Energy Way
West Warwick, RI 02893
800-537-6111
www.triarchinc.com
Printed in USA 11/22/12
©Triarch 2007
This information conforms to the standard detail recommendations
and specifications for the installation of Triarch products as of the date
of publication of this document and is presented in good faith. Triarch
assumes no liability, expressed or implied, as to the architecture,
engineering or workmanship of any project. To ensure that you are
using the latest, most complete information, contact Triarch. Triarch
expressly disclaims all implied warranties, including without limitation,
implied warranties of merchantability and fitness for a particular
purpose.
A Division of Dryvit Systems, Inc.
“Architecture should speak
of its time and place,
but yearn for timelessness.”
Frank Gehry
Sahara DDM2
Alexandria DDM2
Textured Duroplex Dimensional Metals 2 provide a durable metallic finish for interior and exterior space.
Capture the metallic reflection of “Old World Metallurgy” to
unite the performance characteristics and moderate cost of
Duroplex® with the aesthetic appeal of metallic finishes.
Duroplex Dimensional Metals 2 (DDM2) is “Duroplex” tough;
appropriate for use in higher traffic areas. Design options
include metallic patinas in INCA GOLD, STAINLESS STEEL, RUST,
OXIDATION, WELDERS ARC (purple hue) and ELECTRIC
ORANGE.
DDM2 finishes are best achieved over medium or dark toned
backgrounds. To begin, select from our VOC free color chart of
288 colors, an appropriate background color. Next, select a
metallic patina from one of the six options at right. By selecting
a Duroplex pattern or texture option, the process is complete
for design control sample fabrication. Some of the more
popular textural effects include: LUXOR (light stomp base),
SAHARA (Tuscany light pitting base) or ALEXANDRIA (textured
float base). Note – pastel backgrounds do not provide a strong
color contrast with the DDM2 metallic solution.
Duroplex Dimensional Metals 2 works in all sorts of elegant and
themed environments, from public forums, such as exposition
venues to gaming facilities and more sedate corporate
environments. DDM2 finishes are often selected for high traffic
areas because they are Duroplex tough – resistant to abrasion
and impact.
Georgia Aquarium, Atlanta, GA
www.triarchinc.com
800-537-6111
©Triarch 2010
T1226
6 STANDARD METALLIC WASHES
Choose from INCA GOLD, STAINLESS STEEL, RUST, OXIDATION, WELDERS
ARC (purple hue), ELECTRIC ORANGE patinas and glazes to a number of
the Duroplex finishes. Shown below in DDM2 Sahara texture.
Base: Onyx
DDM2: INCA GOLD
Base: Onyx
DDM2: STAINLESS STEEL
Base: Onyx
DDM2: RUST
Base: Onyx
DDM2: OXIDATION
Base: Onyx
DDM2: WELDERS ARC
Base: Onyx
DDM2: ELECTRIC ORANGE
DUROPLEX Dimensional Metals 2
• 6 standard metallic stains over 288 standard
base colors
• Washable
• LEED® Compliant
• Typically installed $3 – $5/sq ft*
• 10-year limited material warranty against
surface mold or mildew growth
• 80% as hard as mild steel
• Most finishes easily patched
• Low VOC
*Based
upon 10,000 sq ft, 9’ ceiling height and average labor rate of $25/hr.
Duroplex® Dimensional Metals 2 (DDM2)
High Performance Seamless Interior Coating
DESCRIPTION
The Duroplex Dimensional
Metals2 (DDM2) line offers
exciting and unique glazing
effects for the Duroplex and
Plexture product lines. Unlike
many of the metallic finishes
available on the market today,
a DDM2 finish is Duroplex
tough. DDM2 finishes
incorporate most of the
performance characteristics
associated with standard
Duroplex finishes, scrub &
abrasion resistant (8000 scrub
cycles), mildew resistant, class
“A” flame & smoke, and a 10
year written product warranty.
Due to the translucent nature of
the DDM2 pigments, we have
found that medium and darker
toned background colors are
necessary to produce the
appropriate effect. Pastels and
off white backgrounds do not
work well with the DDM2
pigment set, therefore, Triarch
will not provide samples of
DDM2 finish in pastel or off
white backgrounds.
• An interior, high solids, one
part water based acrylic
coating,
• Designed to deliver high
performance results at a
moderate price.
• Applies directly to most
common substrates. Class
“A” non-combustible, nontoxic, very low VOC.
• Exceptional performance
growth.
• Use in lieu of vinyl wall
covering.
ADVANTAGES
• Very durable.
• 80% as hard as mild steel.
• Improves the strength of
drywall.
Revised 07/30/2012
©Triarch 2008
10-YEAR WRITTEN
10-YEAR WRITTEN
• High perm rate to achieve
breathability.
• Engineered formulation
combined with a long-term
• Consult warranty
documents for details.
SCRUBBABLE
water.
DESIGN OPTIONS
• Over twenty-five (25) base
• DDM2 GLAZING COLORS
• Inca Gold
•
Stainless Steel
•
Oxidation (copper
oxide – green hue)
•
Rust
•
Electric Orange
•
Welders Arc (purple
hue)
or a design binder.
DELIVERY TIME
Typically ships within 3-5
business days.
T104
FACTORY TRAINED
APPLICATORS*
• Over 600 factory trained
nationally and
internationally.
time.
COST
$3.25 - $5.00 per square
foot.
installed prices.
PRODUCT DATA
SPECIFICATIONS
Pigments
• Barcol Hardness of 38
• Flame/Smoke: Class A
ASTM E-84, Flame spread =
15
• Smoke contribution = 5
Burn
• After Flame Time <0.1
seconds
Perms = 28
• Final dry film thickness of 20
mils
• Qualifies under LEEDS
section 4.2 for low emitting
material
ENVIRONMENTAL
CONDITIONS
Air and surface temperature for
the application must be 50 °F
(10 °C) or higher and must
remain so for a minimum of 24
hours.
DDM2
T104
Installation over Duroplex or
Plexture
Depending upon relative
moisture content of the
Duroplex or Plexture, it may be
necessary to lightly dampen the
substrate (Duroplex or
Plexture) just prior to applying
the Dimensional Metals 2.
Duroplex or Plexture that has
been installed within the
preceding 48 hours may not
need dampening. Try a control
sample board to understand
substrate adsorption and
pattern techniques.
Mixing
Gently stir Dimensional Metals
2 solution before using to
insure uniform viscosity. Some
settling of the metallic flakes
may occur during shipping and
storage. Do not whip material at
a high speed. Typically
Dimensional Metals 2 does not
require thinning and is ready to
use after stirring. If necessary
only thin with small amounts of
water. Too much thinning will
affect performance.
Application
Several techniques are
possible; a common application
technique for DDM2 uses a
“subtractive technique” similar
to antiquing.
It recommended that a
minimum team of two painters
be engaged in the application
of DDM2.
Ring out the rags or towels to a
damp condition prior to use.
Frequently fold the rag or towel
to work with a non-saturated
rag. Rinse rags in clean water
as needed.
Preferred method of application
is to apply Dimensional Metals
2 by spray. Spray equipment
should be either airless or
HVLP spray.
Applying by roller is possible,
but can be tricky. Pay attention
and do not “paint” with the
DDM2. Be careful not to apply
too heavy and do not overlap
your application. Dampen the
substrate to better control
adsorption of the DDM2. Use a
short nap (1/4") roller cover.
(Don’t use a grid or screen, dip
the roller directly into the
DIMENSIONAL METALS 2).
Apply DIMENSIONAL METALS
2 evenly to produce uniform
coverage of the wall. The
product will be somewhat
translucent on the wall and will
shift color as it dries. Avoid
creating ridges or roller lines
with the DDM2.
While the DDM2 is wet
(immediately) on the wall area,
use 100% cotton rags or towels
to “pat the surface” to remove a
portion of the DDM2. Prepare
the rags or towels by first
soaking them in clean water.
pails
100°F.
(3) pails high
Clean Up
Clean tools with water before
Dimensional Metals 2 cures.
Remove masking tape
promptly.
•
RELATED DOCUMENTS
• Guide Specifications T302
• Color brochure
• Warranties T402 & T402M
Installers Manual Chapters 6
&7
Exterior Limitations
Exterior versions of DDM2 are
available. Please contact us for
more details.
* TRIARCH DOES NOT WARRANT, GUARANTEE, OR ASSUME LIABILITY FOR THE WORKMANSHIP OF THE APPLICATOR
Triarch
One Energy Way
800-537-6111
www.triarchinc.com
Revised 11/30/2012
©Triarch 2008
This information conforms to the standard detail recommendations and
specifications for the installation of Triarch products as of the date of
publication of this document and is presented in good faith. Triarch
purpose.
Collection of Joy
T1223
™
Elegant Radiance to any Setting
Over 190 metallic tones of silver and gold to delight your senses. Easily applied by brush, roller or spray.
Argente Collection
Collection of Joy is a sophisticated, water‐based, low VOC ™
metallic paint available in a large selection of silver and gold tones. Color card T1212 Oro provides 84 tonal variations while color card T1213 Argente provides 112 pearlized silver tones. Each of these 196 metallic tones provides the designer or installer exceptional creativity and may be expressed in a variety of patterns and designs, depending upon the application technique. Swirls, combed, cross‐
hatch, Venetian effects and non‐directional applications are possible. Application methods include: brush, roller, painter’s glove and spray. The application method will define the pattern. See our instructions for more details. Unlike more conventional materials, this paint is viscous, allowing the installer to play with the material in either traditional or highly contemporary and original ways. Transform ordinary walls into inspired creations. Moderately priced, easily applied and highly washable are some of the many characteristics of this clever material. Oro Collection
Related Documents: Product DataSheet T119, Color Charts T1212 &
T1213, Guide Specifications T319
COLLECTION OF JOY
FEATURES






196 metallic tones of silver and gold
Washable and abrasion resistant
Exceeds 5000 scrub cycles ASTM 2486
Easily installed by brush, trowel or HVLP
LEED® Compliant
Easily patched if damaged–in many cases
invisibly
 Directly applies to most substrates
 Water clean up
 Visit our website for complete color palette
www.triarchinc.com 800‐537‐6111 Printed in USA R1:08‐20‐12 ©Triarch 2012 Collection of Joy™
T119
Interior Decorative Metallic Paint
DESCRIPTION
Collection of Joy is a waterbased, metallic paint used to
create a variety of highly
decorative metallic effects
on interior surfaces. The
wide range of application
techniques allows the
designer and installer
exceptional creativity.



Available in two bases:
Argente (silver) and Oro
(gold). From the Argente
base, 112 tints may be
created. From the Oro
base, 84 tints may be
created. All 196 metallic
tints are achieved using our
StratoTone™, zero VOC,
APEO free pigment system.
Applied full strength in two
coats over PRIME 1™
absorbent primer to
achieve a variety of lightly
textured metallic paint
effects.
May be applied by roller,
brush, painter’s mitt, a
variety of faux finishing
tools, or spray. Each
application method will
produce a different finish
effect.
DESIGN OPTIONS
Available in a variety of finish
effects. See brochure Oro
T1212 and Argente T1213 for a
suggestion of finish effects and
color options.
DELIVERY TIME
Delivered in a few days,
depending upon your selected
freight. The base: Oro or the
base: Argente are in stock.
APPROVED SUBSTRATES
All common interior building
materials which allow the Prime
1 Primer good adhesion.
©Triarch 2010
ADVANTAGES
 Superior film hardness to
most competing brands.
Scrub testing ASTM 248606 = 5000 cycles to failure.
 Washable without dulling
the finish.
 Pigments are zero VOC
and APEO free.
 Complies with SCAMD
1113 for VOC levels of faux
finishing coatings.
 Quick dry time allows for
minimum wait time between
coats.
 Ease of application. No
product training required.
Many different lightly
textured metallic effects are
easily accomplished.
 Easily repaired. If scratched
or damaged Collection of
Joy may be “spot touched
up”.
APPLICATION
Always create submittals and
mockup before starting the job
to insure design intent. The
desired finish effect will control
the application technique.
The desired finish is created by
applying two coats of Collection
of Joy over Triarch Prime 1
primer. Application of Collection
of Joy may be accomplished by
either: roller, spray, painter’s
mitt, or brush. The application
method chosen will determine
the finish texture. Refer to
Collection of Joy Color Charts
for examples of different
textures or consult with our
representative for textural
options. Collection of Joy
product arrives ready to use.
Thinning is typically not
necessary. All thinning of
Collection of Joy materials must
be done carefully with clean
water. Over-thinning will result
in loss of opacity (hide) and a
reduction of the desired textural
appearance.
1
Prime 1™: Apply by 3/16” nap
roller. Apply in one even coat
without ridges or runs. The
texture created by the Prime 1
will telegraph through the
metallic finish so an even
application is important.
Allow the primer to dry at least
one hour before applying
Collection of Joy. Over nonabsorbent substrates, allow
Prime 1 to dry 2 -4 hours.
Collection of Joy: Select
desired color and the desired
application method/textural
effect from our catalogs T1212
or T1213. Gently stir
thoroughly before use; do
not whip. Regardless of
application method, two coats
are required. Allow the first coat
to dry to the touch before
applying the second.
First coat should be applied
with 3/16” roller cover. Apply
evenly and uniformly without
ridges or runs. The first coat ay
also be applied by HVLP spray
– see spray instructions below.
The second coat is where the
textural effect is developed,
“the pattern coat”. See
illustrated instructions for
application details. Some
options are: brush apply in a
criss-cross pattern with each
stroke at 90 degrees to the
previous stroke; brush in a
vertical or horizontal drag to
achieve a raw silk effect;
repeating circles using a
stippling brush; tight irregular
circles using our special tool;
3/16” roller cover application for
a uniform effect; spray apply for
a non-directional metallic effect.
A roller applied application may
be accomplished with two coats
of Collection of Joy. However
careful attention is required to
not develop roller tracks.
rev 5
T119
Immediately and lightly back
roll wet material to eliminate
any roller tracks.
Spraying: HVLP or
conventional spray equipment
may be used. Thinning is not
typically required. But if
necessary, thin with up to 4
fluid ounces of clean water to
one gallon/3.78 liters. Overthinning of the paint will result
in loss of opacity (hide) and a
reduction of the desired
appearance.
Use an HVLP gun or a
conventional cup gun with the
fluid and air supply from a
pressure pot and compressor.
Air pressure at the HVLP spray
gun needs to be approximately
30 psi, with greater pressures
at the tank, approximately 45
psi.
Examples: Binks- Mach 1
HVLP, with a 94-nozzle set up
(0.55 or 1.4mm diameter fluid
tip and a 90P air nozzle). The
settings for this equipment
were: Fluid Pressure-25psi and
Air Pressure-45psi. Binks-2001
Conventional, with a 66SS air
nozzle set up (0.70 or 1.8 fluid
tips and a 66SD air nozzle).
The settings for this equipment
were: Fluid Pressure-30psi and
Air Pressure-60psi.
Use a NIOSH approved
respirator when spraying.
Provide adequate ventilation.
Use with Venetian Plaster as
metallic glaze: Use Argente or
Oro Collection of Joy to
produce a silver or gold glaze
effect on Venetian Plaster. Mix
in ratio of 4 ounces per liter of
Cera del Vecchio. Add
additional ounces as needed to
produce a stronger effect.
Apply Cera del Vecchio
normally. See document T113
colorants, so no VOC is added
due to colorants.
Taping – Use high quality, lowtack tape for delicate surfaces.
Handling & Storage – Close
all containers tightly when not
in use. Store in a cool, dry
place away from direct sunlight.
Protect from freezing.
Protect from heat over 100°F.
Stack to maximum of three (3)
pails high. Collection of Joy
and Prime 1 Primer have a one
(1) year shelf life.
Coverage – Selected
influence final coverage rate.
One gallon/3.78 liters will cover
approximately 350 to 400
square feet/32.7 to 37 square
meters. Approximately 1.25 1.5 mils dry film thickness per
coat. A minimum of 2.5 - 3 mils
dry film thickness (two coats) is
required for hide and full color
development. Therefore a twocoat application should deliver
around 200 square feet per
gallon.
Clean Up – Clean brushes,
rollers, tool, and equipment with
soap and warm water
immediately after use. Do not
reuse containers and properly
dispose of empty containers.
Warranty*: Five years
manufacture’s warranty against
adhesion failure if applied
according to our specifications
and instructions.
Packaging – Packaged in 1
gallon and 5 gallon pails.
Disposal – Dispose of unused
or unwanted product in
accordance with local laws
regulating water-based
coatings.
Related Documents
T1212 Oro Color Chart
T1213 Argente Color Chart
T319 Long Form Guide
Specifications
Coatings Design – Elegance
Material VOC – Collection of
Joy materials are compliant
with SCAQMD Rule 1113 for
Faux Finishing Coating
Category. VOC levels when
tested under ASTM D 6886:
Argente base: 21 grams/liter
Oro base: 82 grams/liter
Collection of Joy uses
StratoTone zero VOC
* TRIARCH DOES NOT WARRANT, GUARANTEE, OR ASSUME LIABILITY FOR THE WORKMANSHIP OF
THE APPLICATOR
Triarch
One Energy Way
800-537-6111
www.triarchinc.com
©Triarch 2010
This information conforms to the standard detail recommendations and specifications for the
installation of Triarch products as of the date of publication of this document and is presented in
good faith. Triarch assumes no liability, expressed or implied, as to the architecture, engineering
or workmanship of any project. To ensure that you are using the latest, most complete
information, contact Triarch. Triarch expressly disclaims all implied warranties, including without
limitation, implied warranties of merchantability and fitness for a particular purpose.
2
rev 5
“[A designer is] an emerging synthesis
of artist, inventor, mechanic, objective
economist and evolutionary strategist.”
Strata DS II
Buckminster Fuller
Strata DS II
Silk DS III
A decorative faux finish material with performance characteristics that make it perfect for your next project.
T1227
Faulux finishes utilize faux painting techniques for certain
effects, yet realize performance benefits from the use of high
quality acrylics and enhancement agents to achieve
impressive interior spaces.
Faulux finishes boast of over 2000 scrub cycles, making the
finishes durable and abrasion resistant and suitable for a
wide spectrum of uses. All finishes are also washable, Class
“A” Flame Spread and Smoke Resistant and have very low
VOCs.
Westin Cypress Creek, Ft. Lauderdale, FL
Two hundred eighty-eight standard colors and a variety of
textures such as Silk, Silk DM and Strata provide
a wide range of design options to make almost any interior
design special.
Faulux Strata DS III
FAULUX
• Washable
• No seams to peel or curl
• LEED® Compliant
• Standard finishes typically installed $1.50 –
$3.50/sq ft*
surface mold or mildew growth ASTM D 3273
• Easily patched
Based upon 25,000 sq ft, 9’ ceiling height and average labor rate of $25/hr. Premium
finishes will be higher.
www.triarchinc.com
Silver
Cross Hospital, Joliet, IL
800-537-6111
©Triarch 2010
FAULUX®
T103
INTERIOR WALL/CEILING FINISH SYSTEM
DESCRIPTION
•
•
•
water.
An interior, water-based,
high solids, pure acrylic
coating, designed to
decorate faux finish effects
with enhanced
performance results.
Applied directly to most
common construction
substrates.
Class ‘A” non-combustible,
non-toxic, very low VOC.
ADVANTAGES
•
•
Durable, abuse resistant,
easily cleaned, low
maintenance.
Life cycle 8 -10 years with
active use.
5-YEAR WRITTEN COATING
INTEGRITY WARRANTY
5-YEAR WRITTEN
•
•
Against mold and mildew
growing on the surface of
Faulux finish. See written
warranty for detailed
requirements.
Full details are available by
contacting Triarch.
SCRUBBABLE
•
•
Not damaged by water.
Most marks and scuffs
removed after 7—10 days
of curing, using a stiff scrub
DESIGN OPTIONS
Available in a variety of
patterns (unlimited, integral
and multi-color finishes). Call
TRIARCH for samples.
DELIVERY TIME
Quick ship. Smaller shipments
leave the centrally located
factory within 48 hours after
a placed order. Customer
samples and
smaller order may take a little
longer — up to 5-10 days.
INSTALLATION
Applied with traditional painter’s
tools. May require some
decorative painting skills.
FACTORY TRAINED
APPLICATORS*
Factory trained applicators
available nationally, however,
always request a
mockup.
COST
Most projects install between
$.75 - $3.50 per square foot,
depending upon finish selected,
actual job conditions,
elevations, and local labor may
affect installed prices.
PRODUCT DATA
SPECIFICATIONS
•
•
•
•
•
•
•
•
Water based acrylic
Integral and Colorfast
Pigments
ASTM E-84-95, Flame
spread = 15
Smoke Contribution = 0
ASTM E-96B, English Wet
Perms =20~
ASTM D-3960 VOC, 1#/gal.
ASTM D2488 Scrub> 2000
cycles
Dry film thickness of 10
mils, depending upon
pattern
•
•
•
•
•
Packaged in either 1 or 5
gallon plastic pails
Protect from freezing
Protect from heat over
100°F.
Stack to maximum of three
(3) pails high.
One (1) year shelf life.
APPLICATION
Wet application. Always obtain
approval on mockup before
doing the job. Finish selection
will control application
technique. May be spray
applied, roller applied, or
combination techniques.
Sequence depends upon
selected finish.
Triarch
P.O. Box 1014
One Energy Way
800-537-6111
www.triarchinc.com
©Triarch 2007
purpose.
1
T1224
“There is no such thing as a boring project.
There are only boring executions.”
Irene Etzkorn
Dress Shop, MS
Aquarium, GA
The luminous, reflective quality of natural mica allows light to dance off this high-performance interior or exterior finish.
Granyte delivers the rich traditional look of granite, creating spectacular
and durable interior walls or exterior designs at a reasonable price.
For the interior, use Triarch’s Granyte to create the substantial appearance
of quarried granite, with only the expense of a drywall partition and the
Granyte. Consider the use of various drywall reveals and moldings to add
design impact. On the exterior, apply directly to smooth concrete or
masonry substrates to transform the utility of cementitious construction
into the impressive appearance of stone.
Granyte seamless stone finishes are available in 12 standard colors; there
are some custom coloration capabilities, but minimum quantities apply.
Adding optional gold mica to any of the Granyte finishes adds interest to
the wall.
12 Standard Colors
#158 Bloodstone
#154 Raw Silk
#157 Rosewood
#155 Nordic Green
#160 Snow White
#160 Snow White
w/ Gold Mica
#151 Viscount White
#161 Zorro
#161 Zorro
w/ Gold Mica
#156 Labrador
#152 Zimbabwe
#150 Ocean Granite
Simple to apply with basic plastering skills, Granyte is easily and rapidly
installed. Visit our website for technical data and project photos.
GRANYTE
Scan the link to
our project
photos brochure
Granyte colors in
photos:
Above: Snow
White #160
Mid & bottom:
Raw Silk #154
• Practical Washability – ASTM D4828 – high
resistance to staining. Stains easily removed
by ordinary cleaning
• Abrasion resistance – ASTM D 968, ASTM D
4060
• Class “A” – ASTM E 84
• Low VOC – 26 g/l – meets LEED IEQ 4.2
• Typically installed $6.00 – $9.00/sq ft*
*Based upon 3000 sq ft, 9’ ceiling height and average labor rate of
$25/hr.
www.triarchinc.com
800-537-6111
©Triarch 2010
Granyte®
T109
Seamless Stone Wall Finish with Mica Aggregates in Acrylic Resin for Interior or Exterior
SCRUBBABLE
removed after 7 – 10 days
of curing, using a stiff scrub
water.
• ASTM G155 Accelerated
weathering: after 3000 hours
no deleterious effects
• Final dry film thickness of
1/16-1/8 inch
Exceptional performance
growth.
DESIGN OPTIONS
• Twelve (12) standard color
combinations along with
or a design binder.
Use in lieu of stone
veneers. Comprised of
natural aggregates and
mica, no pigment.
DELIVERY TIME
Most orders for standard colors
available within 1 week.
(3) pails high
• Two (2) year shelf life
FACTORY TRAINED
APPLICATORS*
COVERAGE
The recommended coverage is
85-95 (7.9-8.87 ) ) per 65 lb
pail (19 L) at a recommended
thickness of 1.75-3.2 mm (1/161/8 in). Coverage will vary
depending upon the texture and
appearance desired. Granyte
is shipped in a 5 gallon pail.
DESCRIPTION
• An interior or exterior, high
solids, one part water
based acrylic coating,
designed to reproduce the
look of flame cut granite.
• Designed to deliver high
performance results at a
moderate price.
•
•
•
Applies directly to most
common substrates. Class
“A” non-combustible,
breathable, non-toxic, low
VOC.
BENEFITS
Granyte is ready mixed and has
excellent color retention. It is
vapor permeable and is
resistant to dirt pickup, mildew
growth and UV degradation.
• Very durable.
• Interior: High abrasion and
impact resistance.
• Exterior: Provides a
decorative veneer over
concrete or masonry
substrates.
10-YEAR WRITTEN
cracking and chalking.
10-YEAR WRITTEN
SURFACE MOLD/MILDEW
WARRANTY
• High perm rate (45) to
achieve breathability.
• Engineered formulation
combined with a long term
• Full details available by
contacting Triarch.
• Factory trained applicators
available nationally and
internationally.
time.
COST
$5.00 - $7.00 per square
foot.
volume, wall elevations and
installed prices.
PRODUCT DATA
SPECIFICATIONS
Pigments
• ASTM D 4213-83 Scrub
Cycles: passes
• ASTM E-84, Flame spread <
25, = Class A
• ASTM D 3273 Mildew
resistance: passes
• ASTM D 2247 Moisture
Resistance: after 14 days:
no deleterious effects
Perms = 45
pails
100°F.
PROPERTIES
DRYING TIME - The drying
time of Granyte is dependent
upon the air temperature,
relative humidity and finish
thickness. Under average
drying conditions of 70 °F, [21
°C, 55% R.H.], the finish will dry
in 48 hours. Lower
temperatures and higher
humidity will require that the
Granyte finish be protected for
longer periods. Protect work
from rain during the drying
period.
TESTING INFORMATION:
For individual test data on this
product's properties, refer to the
chart included with this
document.
Granyte
APPLICATION PROCEDURE
JOB CONDITIONS - Air and
surface temperature for
application of Granyte must be
50 °F (10 °C) or higher and
must remain so for a minimum
of 48 hours.
TEMPORARY PROTECTION Shall be provided at all times
until, Granyte is dry. If an
exterior application, continue to
protect until permanent
flashings, sealants, etc. are
completed to protect the wall
from inclement weather and
other sources of weather
damage.
SURFACE PREPARATION
• Surface must be smooth and
free of imperfections to
ensure satisfactory
appearance.
• Application surfaces must be
above 50 °F (10 °C) and must
be clean, dry, structurally
sound and free of
efflorescence, grease, loose
paint, oil, form release agents
and curing compounds.
Interior painted surfaces may
be lightly sanded before
application of Triarch’s
Granyte Special Primer™.
• Drywall: (interior only)
Drywall shall be at a level 4.
Apply Granyte Special Primer
followed by Granyte finish per
application instructions.
• Concrete: Shall have cured a
minimum of 28 days prior to
application of Triarch’s
Special Granyte Primer and
Granyte. If efflorescence
form, release agents or
curing compounds are
present on the concrete
surface, the surface shall be
thoroughly washed with
muriatic acid and flushed to
remove residual acid. All
projections shall be removed
and small voids filled with
Triarch’s SKIMM™ or
REFORMIT™ (see product
data sheets for mixing and
application). Triarch’s
Special Granyte Primer shall
T109
be applied to the prepared
concrete surface using a
roller or brush (see product
data sheet for mixing and
application) prior to
application of Granyte.
• Masonry: The masonry
surface, with joints struck
flush, shall be "skim coated"
with Triarch’s SKIMM™ or
REFORMIT™ (see product
data sheets for mixing and
application) to produce a
smooth, level surface.
Triarch’s Special Granyte
Primer shall be applied to
the prepared masonry
surface using a roller or
brush (see product data
sheet for mixing and
application) prior to
application of Granyte.
• Stucco: Triarch’s Special
Granyte Primer shall be
applied over the cured
brown coat using a roller or
brush (see product data
sheet for mixing and
application). If additives are
present in the stucco, a test
patch shall be made and
bond strength checked prior
to application.
Mixing - Just prior to
application, mix the Granyte for
1 minute to ensure uniformity
using a Twister paddle or
equivalent mixing blade,
powered by a high-torque 12.7
mm (1/2 in) drill, at 400-500
rpm. DO NOT OVERMIX. The
Granyte will usually trowel
apply well enough after being
mixed without the addition of
water. If necessary, additional
water can be added in small
increments. The same amount
of water must be added to all
pails of a given batch. Do not
add more than 6 ounces of
water per pail. Contact a
Triarch Field Service
Manager if a given batch of
Granyte needs more than 6
ounces of water per pail to
spread properly.
Application - Colorcoordinated Triarch’s Special
2
Granyte Primer (*see chart
below) shall be applied to all
substrates a minimum of four
hours prior to application of
Granyte. Triarch’s Special
Granyte Primer must be fully
dry before Granyte is applied.
Trowel apply an even layer
onto the primed base coat,
approximately 1.6-3.2 mm
(1/16-1/8 in) thick. With a clean
plastic float, lightly float the
surface of the Granyte finish
using a tight figure 8 pattern.
Float over the finish lightly
several times, cleaning the float
frequently in the process. This
will bring the large mica to the
surface and enhance the
granite appearance. Allow the
Granyte to thoroughly dry for a
minimum of 48 hours under
average drying conditions [21
°C (70 °F), 55% R.H.]. Do not
apply Granyte on surfaces that
will receive sealant. Those
surfaces shall be coated with
Triarch’s Special Granyte
Primer.
Clean Up - Clean tools with
water while Granyte is still wet.
Maintenance - All Triarch
products are designed to
require minimal maintenance.
However, as with all building
products, depending on
location, some cleaning may be
required. See Triarch
publication on cleaning and
optional clear sealer.
Storage - Granyte must be
stored at a minimum of 10 °C
(50 °F) and a maximum of 38
°C (100 °F) in tightly sealed
containers out of direct sunlight.
Granyte
Cautions and Limitations
• Granyte must not be used on
exposed exterior horizontal
surfaces. Minimum slope is
6 in 12, which is 27°
Maximum length of slope is
305 mm (12 in).
• Granyte shall not be used
below grade.
• Granyte is not intended for
direct-applied, exterior
vertical applications over
exterior gypsum based
sheathing board, foam plastic
insulation or other type
insulation board.
• Minor color deviation will
occur due to the natural
aggregate and variations in
raw materials. To achieve
the best color results,
material from the same batch
150
151
152
153
154
155
156
157
158
159
160
161
Granyte Colors
Ocean Granite
Viscount White
Zimbabwe
Lava Stone
Raw Silk
Nordic Green
Labrador
Rosewood
Bloodstone
Dakota Brown
Snow White
Zorro
T109
• number should be applied to
a specific wall section.
Therefore, check batch
numbers before applying
materials.
• Similar to natural stone, some
lot variations within certain
colors will exist. It is
recommended to order
necessary quantity at one
time.
• Granyte shall not be returned
into any sealant joint.
Instead, a coat of Triarch’s
Special Granyte Primer shall
be applied over the base coat
in the joint.
• A site mock-up of sufficient
size [2.4 x 2.4 m (8 x 8 ft)]
shall be coated by the
applicator/contractor with the
Granyte finish to establish
325
365
2002
3095
2220
2330
2251
4120
6900
4140
100
4240
3
• acceptance by the owner,
architect or project manager.
Technical and Field Services
Available on request.
Related Documents:
T1224 brochure
T309 Guide Specifications
T636 Illustrated Application
Instructions
T209 MSDS
Coatings Design – Granyte
Coordinating Granyte Special Primer
Pinstripe
Cable
Storm Cloud
Deep Water
Moonstone
Sage
Mountain Eve
Brick
Bordeaux
Capuccino
White
Onyx
Granyte
T109
Test
Test Method
Surface Burning
Characteristics
ASTM E 84
Water Vapor
Transmission
Accelerated Weathering
Granyte Finish Testing
Criteria
ASTM D 522 Method B
ASTM E 96 Procedure B
Mildew Resistance
ASTM G 154 Cycle 1
(QUV)
ASTM G 155 Cycle 1
(Xenon Arc)
ASTM D 4214 after
ASTM G 154 Cycle 1
ASTM D 2244
CIELAB, 10° Observer
after ASTM G 154 Cycle 1
ASTM E 2485 (formerly
EIMA 101.01)
ASTM D 3273
Salt Spray Resistance
ASTM B 117
Water Resistance
ASTM D 2247
Abrasion Resistance
ASTM D 968 Method A
Falling Sand
Chalk Rating
Instrumentally Measured
Color (includes
yellowing)
Freeze-Thaw Resistance
Adhesion to Concrete
Tensile Bond
ASTM D 4060 Taber
Abrasion (500 g load)
ASTM D 4541
ASTM C 297/E 2134
(formerly EIMA 101.03)
Results
ICC and ANSI/EIMA 99-A-2001
Flame Spread <25
Smoke Developed <450
No ICC or ANSI/EIMA Criteria
ICC: Vapor Permeable No
ANSI/EIMA Criteria
ANSI/EIMA 99-A-2001
2000 hours: No deleterious
ICC: 2000 hours: No deleterious
Passed
Chalk rating: 8 after 5000 hours
QUV
Color change: 5.0 Delta E after
5000 hours QUV
Passed: 3.5" diameter @ 40 °F
45 Perms
ANSI/EIMA 99-A-2001
60 cycles: No deleterious
ANSI/EIMA 99-A-2001
28 days: No growth
300 Hours: No deleterious
14 days: No deleterious
ANSI/EIMA 99-A-2001
500 liters (528 quarts):
No deleterious
ICC and ANSI/EIMA 99-A-2001:
15 psi minimum
ICC and ANSI/EIMA 99-A-2001:
15 psi minimum
>231 psi
60 days: No growth
1000 liters (1057 quarts): No
deleterious
1000 cycles: .83 mg mass loss/rev
>23 psi
1. Finish applied over aluminum panels, bent on cylindrical mandrels as described in ASTM D 522 Method B. Lower diameter indicates higher
flexibility.
2. No cracking, checking, rusting, crazing, erosion, blistering, peeling, or delamination when viewed under 5x magnification.
3. Delta E is total color difference, including yellowing, lightening, darkening, changes in red, blue, and green color values. Finish exposed to
5,000 hours of QUV prior to evaluating Delta E.
TRIARCH
A division of Dryvit Systems, Inc.
One Energy Way
W. Warwick, RI 02893
(800) 537-6111
www.triarchinc.com
Printed in USA R6: 08-15-2013
©Dryvit Systems, Inc. 2003
This information conforms to the standard detail recommendations and specifications for
the installation of Triarch products as of the date of publication of this document and is
presented in good faith. Triarch assumes no liability, expressed or implied, as to the
architecture, engineering, or workmanship of any project. To ensure that you are using
the latest, most complete information, contact Triarch. Triarch expressly disclaims all
implied warranties, including without limitation, implied warranties of merchantability and
fitness for a particular purpose.
4
®
rev. 03
T1222
Oxidized metallic effects easily accomplished by trowel or brush. This unique product adds sophistication & charm to any setting.
KLONDIKE® is a sophisticated paint product providing the
effects of oxidized metals with optional hints of silver and gold.
This contemporary, water-based material has a VOC content of
less than 40 grams per liter, meeting the requirements for
LEED® IEQ Credit 4.2 for low VOC paints.
KLONDIKE is washable, breathable and easily repairable if
damaged. Klondike’s unique appearance allows it to transcend
traditional to contemporary design schemes, making it ideal for
almost every environment. Optional gold, silver and STAR™
effects enhance the general oxidized metal effect. Brochures,
samples and an installation DVD are available through our local
sales representatives. Applied in two coats, Klondike is fast and
easily installed without a formal application training. Most
projects will install for $2.50 – 3.50 per square foot with 9 foot
walls.
KLONDIKE
Scan QR Code for photos
of more installations
www.triarchinc.com
800-537-6111
©Triarch 2012
• 108 premixed colors – in stock
• Washable
• Easily installed by brush or trowel, DVD available
• Low VOC at less than 40 grams/liter meets LEED
IEQ 4.2
• Easily patched if damaged – in many cases invisibly
• Directly applied to most substrates
• Water clean up
• Visit our website for complete color palette
KLONDIKE® LIGHT is a sophisticated paint product providing the
effects of oxidized metals with optional hints of silver and gold.
This contemporary, water-based material has a VOC content of
less than 40 grams per liter, which meets the requirements for
interior paints and coatings in New Construction and Core & Shell
for IEQ Credit 4.2 under LEED®.
KLONDIKE LIGHT is a modern, elegant, water-based variegated
paint for interiors. The decorated surface is washable, breathable
and invisibly repairable without going corner to corner if
damaged. Klondike’s unique appearance allows it to transcend
traditional to contemporary design schemes, making it ideal for
almost every environment. Design options include a gold or silver
accent effect that creates a precious forged metal ambiance. An
additional effect is the STAR sparkle additive which accentuates
the light reflective mineral appearance. Brochures and samples
are available through our local sales representatives. Installation
video is on YouTube.
Klondike Light® on the walls. Collection of Joy™ – Oro on the ceiling.
KLONDIKE LIGHT
• 57 metallic colors – in stock
• Washable
• Easily installed by brush or trowel
• Installation instructions on YouTube. Use QR Code
at top of this page.
• Low VOC at less than 40 grams/liter meets LEED
IEQ 4.2
• Easily patched if damaged - invisibly
• Directly applied to most substrates
• Water clean up
• Visit our website for complete color palette
www.triarchinc.com
800-537-6111
©Triarch 2012
KLONDIKE® & KLONDIKE® LIGHT
T120
Interior Decorative Paint
DESCRIPTION
KLONDIKE is a modern and
elegant water-based
variegated paint for interiors
available in two different
base tones: a traditional
darker base and lighter
base. It is important to select
the correct base for color
reproduction. The decorated
surfaces suggest oxidized
metal fragments within the
paint. Additional
enhancements include gold,
silver and Star effects.
•
•
•
•
•
Klondike traditional is
available in 48 effects.
Klondike Light is available
in 57 effects
Application consists of a
special primer and two
coats of finish.
Applied by trowel or
optionally by brush with a
dry trowel burnish step.
VOC at less than 40 g/l.
May contribute to one point
under LEED IEQ: credit 4.2
DESIGN OPTIONS
Available in 48+57 effects:
a) without a gold or silver
patina
b) with a silver patina
c) with a gold patina
d) with Star G300 effect
DELIVERY TIME
Stock item ready to ship.
APPROVED SUBSTRATES
All common interior building
materials which allow the
Primer 900 or Primer 1000
good adhesion. Surface quality
of the substrates before
application should be equal to a
level 4 drywall finish or better.
Printed in USA
R1 07/2012
©Triarch 2010
Coverage & Packaging
Klondike finish material is
available in 2.5 liter pails. One
pail will cover 147 square feet
of finished wall. (5-6 m2/lt.)
Coverage may vary according
to the smoothness of the
substrate, surface absorption
and application method.
APPLICATION
Application is easy. To
create the colors displayed
in the catalog, carefully mix
by hand; do not use any
kind of electric or shaker
mixing.
KLONDIKE traditional:
with the exact quantity of
COLORI’ coloring paste
required: 15 ml for 2.5 liters
of KLONDIKE. To create the
Gold or Silver effects, add
GOLD ADDITIVE G 100 or
SILVER ADDITIVE G 200 to
the colored KLONDIKE
product, in the following
quantity: 250 ml for 2.5 liters
of KLONDIKE.
KLONDIKE Light: with the
exact quantity of COLORI’
coloring paste required: 5 ml
for 2.5 liters of KLONDIKE.
To create the Gold or Silver
effects, add GOLD
ADDITIVE G 100 or SILVER
ADDITIVE G 200 to the
colored KLONDIKE product,
in the following quantity: 250
ml for 2.5 liters of
KLONDIKE LIGHT.
STAR G300: may be added
to any Klondike or Klondike
Light color.
1
The application for Klondike
traditional and Klondike
Light is the same:
1) Classic effect (using a
Spatula): apply KLONDIKE
with the PV 43 Stainless
Steel Trowel, using uneven
strokes between 6-12
inches (15 -30 cm) long in all
directions, leaving a light
and uneven coating of
product on the surface. After
5 -6 hours at 70◦ F (20°C),
apply the second coat of
KLONDIKE using the same
method as for the first coat
(described previously). Wait
for approximately 1 hour at
◦
70 F (20°C) 20°C and go
over the part which has
already been treated, using
the same PV 43 Stainless
Steel Trowel but with no
product, making criss-cross
strokes approximately 6-12
directions and exerting
pressure so that the color
particles are crushed and
made smaller, thus forming
light and shade effects.
2) Classic effect (Brush +
Spatula): the Classic effect
can also be achieved using
the following application
cycle. Dip the PV 76 brush
into the product, making
sure it is well loaded, and
apply KLONDIKE using
small brushstrokes 3-6
directions, moving from right
to left and vice-versa, and
from bottom to top and viceversa, leaving a light layer of
product which is more or
less uneven. After
approximately 20 minutes at
◦
70 F (20°C) use the PV 43
KLONDIKE® & KLONDIKE® LIGHT
T120
Interior Decorative Paint
Stainless Steel Trowel
(without any product) to
smooth the decorated
surface, working in all
directions. Wait
approximately 5 -6 hours at
◦
70 F (20°C), before
applying the second coat of
KLONDIKE, with the same
PV 76 Brush and using the
same technique as for the
first coat. Wait for
◦
approximately 1 hour at 70
F (20°C) and go over the
part which has already been
applied, using the PV43
Stainless Steel Trowel
(without any product) to
make criss-cross strokes 612 inches (15 -30 cm) long in
all directions and exerting
pressure so that the color
particles are crushed and
made smaller, thus forming
light and shade effects.
3) Brushstroke effect: dip
the PV 76 brush into the
product, making sure it is
well loaded, and apply
KLONDIKE using small
brushstrokes 6-12 inches (15
-30 cm) long in all directions,
moving from right to left and
vice-versa, and from bottom
to top and vice-versa,
leaving a light layer of
product which is more or
less uneven. After
approximately 5 -6 hours at
◦
70 F (20°C), apply the
second coat of KLONDIKE,
using the same technique
as for the first coat. Wait for
◦
approximately 1 hour at 70
F (20°C) and go over the
part already treated with the
PV 76 Brush but without any
product, using criss-cross
strokes in all directions and
exerting pressure on the
surface.
ENVIRONMENTAL
Klondike and Klondike Light
are water based products:
VOC ratings:
Primer 900
27 g/l
Primer 1000
27 g/l
Klondike base 40 g/l
Klondike Light base: 39 g/l
Clean Up – Clean brushes,
rollers, tool, and equipment with
soap and warm water
immediately after use. Do not
reuse containers and properly
in use. Store in a cool dry place
away from direct sunlight.
Protect from freezing.
Stack to maximum of three (3)
pails high. Klondike has a one
(1) year shelf life when stored
properly.
coatings.
* TRIARCH DOES NOT WARRANT, GUARANTEE, OR ASSUME LIABILITY FOR THE WORKMANSHIP
OF THE APPLICATOR
Klondike is a trademark of Valpaint S.p.A. and is under exclusive license to Triarch, a division of Dryvit Systems, Inc.
Triarch
One Energy Way
800-537-6111
www.triarchinc.com
Printed in USA
R1 07/2012
©Triarch 2010
purpose.
2
c
Landscape
Cirrus DS II
Sedona DS II
Lace - Pearlescent
Mist - Pearlescent
The workhorse – a durable, highly-desirable interior finish to meet the demands of today’s busy interior spaces.
Plexture is the interior design workhorse; a moderately priced
wall finish with durability few other interior wall materials can
match. This seamless, acrylic textured finish is aggressively
priced; with a typical installation price below $0.75/sq.ft. for a
standard Plexture finish for medium scale commercial
installations with national average labor costs. The appearance is
similar to many knock down finishes, but the durability,
washability, abuse resistance and mold & mildew resistance have
allowed Plexture to capture a large percentage of the hospitality
marketplace.
More design options are available with the Premium Plexture
finishes such as Symphony, Sedona DS II, and Orange Peel.
Premium patterns Lace & Mist add a subtle high performance
pearlescent effect. Premium Plexture will typically install for
$1.00-1.25 per square foot under the same project conditions.
Regardless of the finish selected, Plexture is highly scrubable and
is warranted against mold and mildew growth (ASTM D 3273).
Visit our website for all our technical data.
T1221 - PP
Sedona DS II
Embassy Suites Lobby, Houston, TX
Cirrus DS II
Embassy Suites Restaurant, Houston, TX
now more
design options
PLEXTURE
•
•
•
•
•
•
•
288 standard colors as well as custom colors
Integral color and colorfast
Abrasion resistance – ASTM C 1629
Breathable – perm rate of 21
No seams to peel or curl
LEED® Compliant – IEQ 4.2 low VOC
Standard finishes typically installed $0.60 $0.75/sq ft*
Premium finishes are more expensive
QR code for link:
Coatings Design©
• Washable
• Easily patched
* Based upon 25,000 sq ft, 9’ ceiling height and average labor rate of
$25/hr. Premium finishes will be higher.
Embassy Suites Mezzanine Level, Houston, TX
www.triarchinc.com
800-537-6111
Printed in USA R2: 08-23-13
©Triarch 2010
The Plexture® system is made up a series of patterns and effects. Be certain to understand if
the selected pattern is within the standard Plexture line or the Premium Plexture line. Coverage
rates, application methods and product cost will vary from pattern to pattern.
Triarch
One Energy Way
800-537-6111
www.triarchinc.com
and specifications for the installation of Triarch products as of the
date of publication of this document and is presented in good faith.
Triarch assumes no liability, expressed or implied, as to the
architecture, engineering or workmanship of any project. To ensure
that you are using the latest, most complete information, contact
Triarch. Triarch expressly disclaims all implied warranties, including
without limitation, implied warranties of merchantability and fitness
for a particular purpose.
PLEXTURE® System
T110
LOW PROFILE TEXTURED COATING
DESCRIPTION
•
A two component interior,
water-based, high solids,
pure acrylic coating
designed to deliver
excellent performance
results at an economical
price. Applied directly to
most common construction
substrates.
•
Class “A” non-combustible,
non-toxic, low VOC.
•
Use instead of traditional
paint and texture, or as a
cost savings to vinyl wall
covering.
ADVANTAGES
• Durable, abuse resistant,
easily cleaned, low
maintenance.
•
active use.
5-YEAR WRITTEN
WARRANTY PERFORMANCE
5-YEAR WRITTEN
• Against mold and mildew
Plexture.
• ASTM D3273-00
Resistance to Mold –
extended testing =
10 (no growth)
• Full details available by
contacting Triarch.
SCRUBBABLE
water.
Ver: 03
©Triarch 2008
DESIGN OPTIONS
Available in a variety of patterns
and almost unlimited integral
colors, both in monochromatic
and multi-color finishes. Call
TRIARCH for samples. Pattern
options include:
• Sierra
• Landscape
• Cirrus
• Splatter
• Sierra DS II
DELIVERY TIME
Quick ship, smaller shipments
leave the centrally located
factory within 2-3 business days
after a placed order. Custom
samples and larger orders may
take a bit longer (up to 5-10
days).
FACTORY TRAINED
APPLICATORS*
•
•
nationally.
National training program
helps to ensure quality
control and minimize
installation time.
COST (typical installed)
•
Plexture finishes install
between $.55 - $.75 per
square foot. Premium Series
finishes are around $0.90 $1.20 per square foot.
Standard. Prices assume
square footage minimums
and all work can be
executed while standing on
the ground.
•
Actual job conditions,
installed prices.
PRODUCT DATA
SPECIFICATIONS
•
Pigments
•
Flame/Smoke: Class A
ASTM E-84-95, Flame
spread = 15, smoke
Contribution = 0
•
Perms = 21.93
•
VOC level per ISO 11890-2
less than 20 g/L
•
ASTM D2486 Scrub
4300 cycles Landscape
3500 cycles Sierra
•
ASTM D3273-00 Mold = 10
(extended test: no growth)
•
Dry film thickness of a
random 4 – 10 mils
depending upon pattern
ENVIRONMENTAL
APPLICATION CONDITIONS
the application area must be 50
°F (10 °C) or higher and must
hours.
APPLICATION
tools – airless and/or texture
sprayer. Sequence depends
upon selected finish. Two
components make the Plexture
System: Texture Coat and
FineCoat 2. Some finishes will
require a “knock-down” process.
Installation instructions available
to qualified purchasers.
®
PLEXTURE System
pails
• For smaller order quantities,
some products may be
shipped in 1 gallon pail
• Protect from heat over 100°F.
(3) pails high.
• One (1) year shelf life.
T110
RELATED DOCUMENTS
• StratoTone color chart
• Plexture Premium Series
System Data Page T125
• Guide Specifications T310
• Color brochure
• Coatings Design – Plexture
• MSDS T210
• Warranties T410 & T410M
• Cleaning Instructions T511
• Repair Instructions T515
• Test Data Summary T1215
• Installer’s Manual Chapter 9
• Refer our website for above
documents
CLEAN UP
Clean tools with water the same
day before Plexture System
cures. Remove masking tape
promptly.
Triarch
One Energy Way
800-537-6111
www.triarchinc.com
PLEXTURE® Premium Series
DESCRIPTION
An interior, water-based,
high solids, pure acrylic
coating designed to deliver
excellent performance
results at an economical
price. Applied directly to
most common construction
substrates.
Class “A” non-combustible,
non-toxic, low VOC.
Use instead of traditional
paint and texture, or as a
cost savings to vinyl wall
covering.
Premium series provides
additional design options
and patterns to the baseline
Plexture system
ADVANTAGES
Durable, abrasion resistant,
easily cleaned, low
maintenance.
active use.
5-YEAR WRITTEN
WARRANTY PERFORMANCE
5-YEAR WRITTEN
Against mold and mildew
Plexture.
ASTM D3273-00
Resistance to Mold –
extended testing =
10 (no growth)
Full details available by
contacting Triarch.
SCRUBBABLE
Not damaged by water.
Most marks and scuffs
water.
©Triarch 2008
DESIGN OPTIONS
Premium Series extends the
design options for the Plexture
System by providing a range of
designer options, including
pearlescent effects. Pattern
options include:
Symphony pattern
Plateau pattern
Sedona pattern
Cirrus DS II
Orange peel
Mist pattern
Lace pattern
DELIVERY TIME
Quick ship, smaller shipments
leave our factory within 2-3
business days after a placed
order. Custom samples and
larger orders may take a bit
longer (up to 5-10 days).
FACTORY TRAINED
APPLICATORS*
nationally.
National training program
helps to ensure quality
control and minimize
installation time.
COST (typical installed)
Premium Series finishes are
around $0.90 - $1.20 per
square foot. Standard
Plexture finishes install
between $.55 - $.75 per
square foot. Prices assume
square footage minimums
and all work can be
executed while standing on
the ground.
Actual job conditions,
installed prices.
T125
PRODUCT DATA
SPECIFICATIONS
Low VOC water based
100% acrylic resin
Pigments
Flame/Smoke: Class A
ASTM E-84-95, Flame
spread = 15, smoke
Contribution = 0
Perms = 21.93
ASTM D2486 Scrub:
exceeds 4500 cycles
ASTM D3273-00 Mold = 10
(extended test: no growth)
Dry film thickness of a
random 4 – 10 mils
depending upon pattern
ENVIRONMENTAL
the application area must be 50
°F (10 °C) or higher and must
hours.
APPLICATION
tools – airless spray and texture
sprayer such as the Graco
Texspray 1500. Some finishes
may also use a HVLP spray
application. The sequence of
material application depends
upon the finish selected.
Installation instructions available
to qualified purchasers.
Typically Plexture may be
applied directly to unprimed
drywall. However from time to
time and depending upon the
substrate and type of drywall
compounds used, it may be
necessary to apply a thin coat of
our Prime 1™ to avoid any
flashing. Prime 1 may be applied
by airless or roller.
PLEXTURE
®
Premium Series
T125
MIXING
Stir all materials after opening.
Do not whip material at a high
speed. Certain components may
require thinning with clean
water. Reference texture specific
installation instructions. Too
much thinning will affect
performance.
Shipped in 5 gallon plastic
pails
For smaller order quantities,
some products may be
shipped in 1 gallon pail
Protect from freezing
Stack to maximum of three
(3) pails high.
CLEAN UP
Clean tools with water the same
day before Plexture System
cures. Remove masking tape
promptly.
RELATED DOCUMENTS
StratoTone color chart
Plexture System Data Page
T110
Guide Specifications T310
Color brochure
Coatings Design – Plexture
MSDS T210
Warranties T410 & T4102M
Cleaning Instructions T511
Repair Instructions T515
Test Data Summary T1215
Installer’s Manual Chapter 9
Refer our website for above
documents
One (1) year shelf life.
Triarch
One Energy Way
800-537-6111
www.triarchinc.com
Bicolore (2 Color)
Classico (1 Color)
Spatula Stuhhi® Venetian plaster imported from Italy recreates Old World renaissance finishes for today’s refined interiors. T1225
An interior, slaked lime and ground marble veneer plaster
finish system, designed to deliver a sophisticated &
decorative finish for the commercial and residential
marketplace. Finish options include: gloss, matte, waxed,
unwaxed, metallic glazes, and multi color blends.
Spatula Stuhhi is applied by decorative faux artists and
many commercial painting companies. Ask us for a listing
of approved installers in your area.
Application consists of a special primer, two or three coats
of plaster and a recommended natural wax topcoat (Cera
del Vecchio) to seal the surface of the plaster.
Slaked lime polished plaster is available in three plaster
options:
•
•
•
Richlin Interiors, Naples, FL
Classic high sheen (item 1001)
OPACO matte finish (item 1014)
Spirito Libero lightly textured matte finish (item
1060)
DESIGN OPTIONS
•
•
•
Available in 147 standard colors, plus custom
colors available.
Optional metallic and pearlescent glazes
Terracotta burnt earth effect
Completed project photos and videos are on our website.
Georgia Pacific Corporate Offices, Atlanta, GA
VENETIAN POLISHED PLASTER
FEATURES
• Slaked lime and marble based plaster
• Gloss and matte effects
• Pearlescent and metallic glazes
• LEED VOC compliant at less than 5 grams/liter
• Non-fading colors
• Flame/Smoke: Class A
• Washable
• Breathable and mold & mildew resistant
• Complete system film thickness approx: 10 mils
• 10 year warranty when applied by factory approved
installer
• Typically installed $6.00 - $10.00/sqft*
Private Residence, Lake Tahoe, CA
www.triarchinc.com
Cherokee
Country Club, Knoxville, TN
800-537-6111
©Triarch 2010
* Minumum of 1,500 sqft, 9’ ceiling height and average labor rate
of $25 - $30/hour. Some markets will be higher due to local labor
prices.
SPATULA STUHHI™, Spirito Libero™ & Opaco™
T113
TRANSLUCENT VENETIAN PLASTER
DESCRIPTION
A high quality interior, lime and
ground marble based thin coat
polished plaster finish system,
designed to deliver a
sophisticated & decorative
finish for the commercial and
residential marketplace. Finish
options include: gloss, matte,
waxed, unwaxed, stencils,
metallics, and multi color
blends. Refer to e-document
T651 “Technical Overview”
for more detailed system
explanation.
DESIGN OPTIONS
Includes a wide range of
standard color options, as well
custom colors. Available in a
range of sheen levels, as either
a gloss (Classico) or various
matte finishes (Marmo, OPACO
of Spirito Libero). Additional
effects: metallic glazes,
banding, and multi color effects.
Optional wax topcoat improves
washability. Mineral plaster
options include:
 Classico (item 1001),
 OPACO (item 1014)
 Spirito Libero (item
1060)
Recommended Cera del
Vecchio™ natural wax topcoat
to seal the surface to enhance
cleaning and stain resistance is
available. Additional optional
effects can include metallic
glazes.
METALLIC GLAZING: Use
Argente or Oro Collection of
Joy™ product to produce a
silver or gold glaze effect on
Venetian Plaster. Mix in ratio of
4 ounces per liter of Cera del
Vecchio. Add additional ounces
as needed to produce a
stronger effect. Apply Cera del
Vecchio normally.
Call TRIARCH for samples,
color charts, or a design binder.
Website: www.triarchinc.com.
NO SPECIAL SUBSTRATE
NEEDED
Applies to all clean, sound,
unpainted drywall, concrete,
masonry or wood substrates.
Requires minimum of a level 4
or equivalent type drywall finish
for the substrate.
10-YEAR WRITTEN
WARRANTY*
When entire system is applied,
Spatula Stuhhi plaster carries a
10 year warranty against
peeling, delamination, cracking
and chalking.
MILDEW RESISTANT
High alkaline formula helps to
prevent mold or mildew growth
on the surface of the plaster.
DELIVERY TIME
Most orders leave a regional
warehouse within 2-3 b-days.
FACTORY TRAINING
Factory trained applicators
available nationally.*
COST
Most projects install between
$5.00 - $10.00 per sq. ft;
depending upon quantity, wall
height, local labor rates and
final effect. Job conditions may
also affect installed price.
PRODUCT DATA
SPECIFICATIONS
 Lime and marble based
plaster
 Complies with LEED and
Green Seal IEQ 4.2 for low
VOC materials.
 Zero VOC, APEO free
pigments, integral &
colorfast.
 Ultraviolet, wet/dry,
heat/chill no failures
 Class A Flame/Smoke:
ASTM E-84, Flame spread
= 8.5, Smoke contribution =
0.0
INSTALLATION
Consists of a special primer
(GEXXO™) and a 2 or 3 coat
steel trowel application process
of the selected special mineral
plaster to produce the desired
finish. After initial cure, apply a
special high pH resistant wax,
Cera del Vecchio, to finish the
effect and to provide stain
resistance and improved
cleaning.
FINISH QUALITY
Applied film thickness is
approximately 10 mils. The
typical finish is smooth to the
touch, almost glass like. Must
be trowel applied and be a multi
coat system using our primer
and wax for any warranty to
apply.
Taping – Use high quality, lowtack tape for delicate surfaces.
Coverage – Selected plaster
type will influence the coverage
rate as does the skill of the
installer. Shown below are
typical coverage rates.
Pkg Size # of coats
Final Yield
in sq.ft.
Prime 1
1
250/gal
1001/24
1060/24
1014/24
3
2
2
300+
200-250
200-25
1001/8
3
80-90
1060/8
2
60-75
1014/8
2
60-75
influence final coverage rate.
1001/2
1060/2
1014/2
3
2
2
Cera del Vecchio
©Triarch 2007
Rev: 04
22-30
10
10
500
SPATULA STUHHI™, Spirito Libero™ & Opaco™
T113
TRANSLUCENT VENETIAN PLASTER
Clean Up – Routinely clean
all sidewalls of partially used
pails using a damp sponge.
Interior sidewalls of pails
should be free of any
material before resealing any
lids. Dried material or
“crumblies” will fall into the wet
material and render wet
material unusable. Clean rollers
and trowels with warm water
immediately after use. Properly
Material VOC – Spatula Stuhhi
branded plasters are ultra-low
or free from VOC content. The
pigments used to color the
plaster are from the StratoTone
collection of pigments, which
are zero VOC rated pigments
and are APEO free.
in use. Store in a cool, dry
place away from direct sunlight.
Protect from freezing,
product is typical not useable
after one freeze. Protect
from heat over 100°F. Stack
to maximum of three (3) pails
high. At least a two year shelf
life with proper storage.
coatings. When allowed to
harden, Venetian Plaster
typically qualifies as solid land
fill, check local regulations.
Related Documents
Venetian Plaster Brochure
Spatula Stuhhi Catalog
Spirito Libero Catalog
T1234 Polished Plaster tip card
T313 Spatula Stuhhi Guide
Specifications
T651 Technical Overview
T413 Warranty
Coatings Design - Elegance
Product Videos Landing Page
 Available in 24 kilo pails (5
gallon pails) or 8 kilo pails
 Pigment system may be
factory pre-mixed or
shipped separately at
customer request.
 Protect from freezing
 Protect from heat over
100F.
*TRIARCH DOES NOT WARRANT, GUARANTEE, OR ASSUME LIABILITY FOR THE WORKMANSHIP OF THE APPLICATOR.
IT IS HIGHLY RECOMMENDED TO HAVE A MOCK UP WALL INSTALLED PRIOR TO AUTHORIZATION TO INSTALL THE WORK.
Triarch
One Energy Way
800-537-6111
www.triarchinc.com
This information conforms to the standard detail recommendations and specifications for the
installation of Triarch products as of the date of publication of this document and is presented in
good faith. Triarch assumes no liability, expressed or implied, as to the architecture, engineering
or workmanship of any project. To ensure that you are using the latest, most complete
information, contact Triarch. Triarch expressly disclaims all implied warranties, including without
limitation, implied warranties of merchantability and fitness for a particular purpose.
©Triarch 2007
2
rev 04
CT-100™
T100
WEATHERPROOF CONCRETE COATING
DESCRIPTION
High quality water based
coatings for use on exterior or
interior concrete, stucco,
masonry, and primed metal
surfaces. Available in smooth
(un-aggregated), fine, medium,
and coarse textures.
•
This product is non-toxic by
the Federal Hazardous
Substance Act. In
California, it meets CARB
and VOC requirements.
Please refer to the
Material Safety Data Sheet
for specific information.
COVERAGE RATES
Smooth:
Fine:
Medium:
Coarse:
100 sq. ft./gal. + 20
65 sq. ft./gal. + 10
50 sq. ft./gal. + 10
40 sq. ft./gal. + 10
Coverage rates are estimates.
The actual coverage will vary
depending on the porosity and
texture of the substrate.
RECOMMENDED USE
•
•
Total solids, by weight (%)
Total solids, by volume (%)
Viscosity, KU
Weight per gallon, lb.
PH
Flexibility
Mildew Resistance
Weathering
Flame Spread
57 + 2
44 + 2
104 + 2
10.4+ 2
9.2 + .2
Pass
Excellent
Pass
Class A
This product meets or
exceeds DOT standards for
concrete structures in many
states. CT-100 coatings
meet or exceed Federal
Government Specification
TTC-555B, Type I and II,
and all EPA and OSHA
standards for this type of
coating.
©Triarch 2007
Concrete Block:
Use TRIARCH’s SKIMM™
or Fill-o-Block™ compound
depending on the desired
appearance, either
completely floated (SKIMM)
or partially filled (Fill-OBlock). Refer to product
data pages for specific
LIMITATIONS
Previously Coated Surfaces:
Do not apply this product when
the surface or ambient
temperatures are below 45°F or
expect to drop below 45°F
within a 24-hour period. This
product is not recommended for
below grade use or use on
back filled retaining walls. Do
not apply during rain or if rain is
expected within 24-hours after
application. Do not apply to
floors or horizontal surfaces
where standing water can
occur.
Pressure wash the entire
surface area with hydro-spray
equipment (2,000-2,500 PSI
minimum) to remove all dirt,
mildew, chalk, or other foreign
contaminants. Let it dry
completely. If needed, apply
TRIARCH’s Masonry
Conditioner product, to tiedown any chalky residue.
SURFACE PREPARATION
When properly applied, CT100 coatings provide a long
lasting film of protection for
commercial, industrial, and
residential structures.
• Alkali Resistant: Masonry
Conditioner (Clear)
• Standard Primer: Prime 1™
(Pigmented/tintable)
•
TECHNICAL DATA
Type: Vinyl Acrylic emulsion.
Grades: Smooth, fine,
medium, and coarse.
Finish: Matte finish, slight
angular sheen.
Colors: Triarch standard or
custom.
Packaged: Available in 5gallon plastic pails
and 55-gallon metal
drums.
masonry and stucco surface 28
days to cure.
Concrete and Stucco Primers:
This product is to be applied
only to clean, dry, sound
surfaces. The type and degree
of surface preparation will
determine the appearance of
the finished project. CT-100
coatings will not fill voids in
substrates nor hides all
imperfections.
New Construction:
Concrete, stucco, and masonry
surfaces must be cured and
free of excess moisture prior to
the application of CT-100
coatings. Allow new concrete,
1
Surface Repair:
Repair any cracks and surface
imperfections prior to the
application of the finish coats.
Apply a coat of CT-100 smooth
coating to bridge most existing
hairline cracks with no
additional preparation being
necessary. Use TRIARCH’s
™
™
Durofloat or SKIMM product
to repair cracks larger than
hairline. Refer appropriate
product data guides for specific
CT 100 Weatherproof Concrete Coating
T100
CT-100 smooth:
Airless
COATING APPLICATION
CT-100 smooth and fine texture
coatings may be applied with a
brush, roller, or spray
equipment. CT-100 medium
and coarse textures must be
applied using air-powered
spray equipment only. MIX CT100 coating thoroughly with a
power drill and mixing blade
prior to use.
SPRAY APPLICATION
Spray application is
recommended for all grades of
CT-100 product. Contact
TRIARCH’s customer service
or your preferred paint spray
equipment manufacturer for
specific recommendations.
Triarch
P.O. Box 1014
One Energy Way
www.triarchinc.com
©Triarch 2007
CT-100 textured: TRIARCH
cannon or
equivalent.
LIMITED WARRANTY
GENERAL STATEMENT:
Subject to certain limitations,
TRIARCH warrants this product
for one (1) year against defects
in materials at the time of
purchase and to perform as
represented in our factory
published literature. Interested
parties should refer to the
published warranty statement
for specific wording, exclusions,
and product limitations. It
should be noted that the
warranty is predicated upon
proper application procedures,
and other considerations
pertaining to the use of this
product that are beyond the
control of the manufacturer.
TRIARCH does not warrant the
workmanship of the contractor.
Under no circumstances is
TRIARCH liable for
consequential damages.
Triarch expressly disclaims all
other implied warranties,
including implied warranties of
merchantability and fitness for a
particular purpose. Warranty
claims will not be honored
unless TRIARCH has the
opportunity to inspect the
problem areas of the incident,
and before repairs are
undertaken. TRIARCH offers
extended warranties under
specific conditions. Contact
TRIARCH for extended
warranty requirements.
purpose.
2
ELAST-O-FLEX™
T106
ELASTOMERIC COATING
DESCRIPTION
ELAST-O-FLEX™ elastomeric
coatings are high quality water
based products that provide a
flexible, durable, waterproof
membrane on specified vertical
wall surfaces when applied as
directed. These qualities are
only achieved through proper
surface preparation, product
selection and application
technique that provides a
pinhole free film at a minimum
15 mil DFT.
requirements and CARB and
VOC requirements where
applicable.
TECHNICAL DATA
Acrylic emulsion
(Internally plasticized)
Grades:
Smooth, fine, medium
and coarse
Finish:
Matte finish, slight
angular sheen
Colors:
Triarch standard or
custom
Packaged: Available in 5-gallon
plastic pails and 55gallon metal drums.
Fire Resistance:
Class A
Percent solids by weight:
(%) – Smooth
Fine
Medium
64 + 2
67 + 2
67+ 2
Coarse
65 + .2
Percent solids by volume:
(%) – Smooth
Fine
Medium
55 + .2
Type:
COVERAGE RATES
60 + 2
83+ 2
Viscosity
PH
82 + 2
114 + 4 Kus
9.5 + 2
Freeze/thaw cycles
Tensile strength
Weight per gallon
Pass
100 + 10 PSI
11.4lb. + .5
Elongation
Deep cup cracking
Wind driven rain
400% + 20
None
Pass
Perms
4.0 + .1
Coarse
•
Concrete, stucco and
masonry services must be
cured and free of excess
moisture prior to the
application of ELAST-OFLEX coatings. Allow new
concrete, masonry and
stucco surfaces 28 days to
cure.
Concrete and Stucco Primers
Alkali Resistant: Masonry
Conditioner (Clear)
Standard Primer: Prime 1™
(Pigmented/tintable)
Concrete Block
Use TRIARCH’s SKIMM® or
Fill-o-Block™ compound
depending on the desired
appearance, either completely
floated (SKIMM) or partially
filled (Fill-O-Block). Refer to
product data pages for specific
SURFACE PREPARATION
Metal
Coverage rates are estimates.
The actual coverage will vary
depending on the porosity and
texture of the substrate.
This product is to be applied
only to clean, dry, and sound
vertical surfaces. The following
are the recommended surface
preparations for most approved
surfaces. For surfaces other
than specifically addressed
here, contact your local
TRIARCH Representative for
detailed information.
RECOMMENDED USE
New Construction
ELAST-O-FLEX elastomeric
coating is designed for
application to properly prepared
vertical wall surfaces, including
stucco, concrete block, exterior
insulated wall systems, and
primed metal. ELAST-O-FLEX
coating meets or exceeds TTC555B, Types I and II. It is nontoxic by the Federal Hazardous
Substances Act and does not
contain lead or mercury. It
meets all EPA and OSHA
•
Remove rust and all foreign
materials from the surface.
New or weathered galvanized
surfaces will require the
removal of the “white rust” or
rolling oil. A mild phosphoric
acid wash may be used for this
purpose. Rinse the surface
with clean water and allow to
dry. Prime the surface with
zinc chromate primer according
to the manufacturer’s
instructions. Apply two coats of
ELAST-O-FLEX elastomeric
Coating.
Smooth:
20
Fine:
Medium:
Coarse:
100 sq. ft./gal. +
65 sq. ft./gal. + 10
50 sq. ft./gal. + 10
40 sq. ft./gal. + 10
©Triarch 2007
The surface must be
clean, dry, cool, free of
grease, surface
hardeners, mildew, curing
agents, bond breakers,
and other foreign matter.
area with high-pressure
hydro-spray equipment to
remove construction dirt
and other contaminants.
Rinse and let dry.
1
Previously Coated Surfaces
surface area with hydro-spray
equipment (2,000-2,500 PSI
minimum) to remove all surface
contaminants. Remove any
mildew with a diluted bleach
solution. Rinse it with clean
water and allow it to dry.
Chalky surface will require a
ELAST-O-FLEX™
T106
coat of TRIARCH’s Masonry
Conditioner product following
the recommended application
procedures contained in the
product data guide.
Surface Repair
Repair any cracks and surface
imperfections prior to the
application of the finish coats.
Apply a coat of ELAST-O-FLEX
smooth coating to bridge most
existing hairline cracks with no
additional preparation being
necessary. Use TRIARCH’s
®
®
Durofloat or SKIMM product
to repair cracks larger than
hairline. Refer to appropriate
product data guides for specific
MIXING INSTRUCTIONS
Thoroughly mix all materials
with a low speed mixer before
use. Avoid over mixing to
minimize the introduction of
excess air into the product.
COATING APPLICATION
After specified surface
preparation is completed and
the surface is dry, apply the first
coat of ELAST-O-FLEX
elastomeric Coating at the
recommended coverage rate.
The first coat should always be
smooth (un-aggregated). Back
roll the first coat to eliminate
trapped air and minimize
pinholes in the film. Allow the
first coat to thoroughly dry
before applying the second
coat. Apply the second coat of
either smooth or textured
ELAST-O-FLEX coating at the
recommended coverage rates.
Apply the first and second coat
of ELAST-O-FLEX elastomeric
Coating so as to achieve a
pinhole free film and a
combined minimum 15 mils
DFT.
EQUIPMENT
RECOMMENDATIONS
SPRAY APPLICATION
Spray application is
recommended for all grades of
ELAST-O-FLEX coating.
Contact customer service or
your preferred paint spray
equipment manufacturer for
specific recommendations.
ELAST-O-FLEX smooth: Airless
ELAST-O-FLEX textured: Triarch
“Cannon” or
equivalent
LIMITED WARRANTY
GENERAL STATEMENT:
TRIARCH warrants this product
for five (5) years against
defects in materials at the time
of purchase and to perform as
for specific wording, exclusions
proper application procedures,
TRIARCH does not warrant the
product as adequate for every
purpose, nor does it warrant the
TRIARCH liable for
consequential damages.
Triarch expressly disclaims all
other implied warranties,
including implied warranties of
merchantability and fitness for a
particular purpose. Warranty
claims will not be honored
unless TRIARCH has the
opportunity to inspect the
problem areas of the incident,
undertaken. TRIARCH offers
TRIARCH for extended
warranty requirements.
Triarch
P.O. Box 1014
One Energy Way
800-537-6111
www.triarchinc.com
©Triarch 2007
2
TM
SKIMM™ & DUROFLOAT™
T101
A HIGH PERFORMANCE FILLING COMPOUND
instructions for additional
details.
DESCRIPTION
•
•
•
An interior/exterior, one part,
water based filled acrylic
compound that is utilized by
itself for filling and skimming
mortar, grout lines in new or
painted CMU, block, brick, etc.
up to 3/8” deep and for
“sacking” new concrete.
For surfaces with average 3/8”
or greater irregularities, use our
REFORMIT™ product. Refer to
data page T116.
SKIMM and Durofloat use the
same acrylic chemical
technology. SKIMM uses larger
aggregate filler, while Durofloat
uses a finer aggregate. SKIMM
fills faster, but Durofloat
produces a finer surface which
may be necessary for thin film
paint finishes.
ADVANTAGES
•
Cures very hard
•
Over 85% solids results in very
low shrinkage to save labor.
•
High adhesion to all masonry
and concrete. May also provide
high adhesion to certain glazed
products, like tile, but a test
area is suggested.
•
Directly apply to concrete,
masonry, or painted surfaces.
High perm rating promotes
breathable substrates and
resists mold and mildew.
•
Water Resistant
•
Excellent for exterior joint
flushing for cement or masonry
boards. See installation
Triarch
One Energy Way
800-537-6111
www.triarchinc.com
Rev: 03
©Triarch 2007
•
Also good for uses in high
humidity areas such as Jacuzzi
rooms, pool rooms, laundries,
etc. (Not for use in standing
water).
•
Water based acrylic technology
meets LEED Low VOC criteria.
SPECIFICATIONS
•
Water base pure acrylic
•
Inorganic fillers
•
Pencil Hardness: 9H
•
Flame spread: Class A
ASTM E84 = 8.0
•
Zero VOC
•
Shipped in 5 gallon plastic pails
•
Net weight per pail = 65 lbs.
•
Shipping weight per pail = 68
lbs.
•
Protect from freezing and heat
over 100°F.
•
Typically ships within 2
business days of order from 1
of our 4 plants. Manufacturing
in RI, GA, OK, and CA.
•
•
•
•
Packaged in a 5-gallon pail,
simply remove the lid “and
go”.
At the installers option; trowel,
spray or texture roller apply
directly to the substrate. Knife
it flat, throwing the excess
back into the pail for future
use; very little material waste
and no wasted labor preparing
materials.
With zero VOCs, SKIMM
meets all LEED low emitting
material criteria.
Be certain to review any
substrate specific
specifications and installation
guidelines.
HOW TO SPECIFY
In varying or uncertain job
conditions, specify both options
and allow the contractor to make
the choice of which to use. The
specifications contained in the
architectural binder call for
SKIMM/Durofloat compound. The
contractor should determine the
correct product for the site
conditions. The materials cost the
same, so labor will be the only
variable factor in material
selection, so allow the contractor to
judge whether the job calls for
SKIMM or Durofloat compound.
USING SKIMM & DUROFLOAT
•
•
•
•
Wall surfaces on indoor
swimming pools.
To level or smooth all forms of
masonry construction to hide
grout lines.
To improve inferior concrete
pours.
Interior or exterior
This information conforms to the standard detail
recommendations and specifications for the installation of
Triarch products as of the date of publication of this
document and is presented in good faith. Triarch assumes no
liability, expressed or implied, as to the architecture,
engineering or workmanship of any project. To ensure that
you are using the latest, most complete information, contact
Triarch. Triarch expressly disclaims all implied warranties,
including without limitation, implied warranties of
merchantability and fitness for a particular purpose.
RELATED DOCUMENTS:
T301 SKIMM long form guide
specifications
T116 REFORMIT
T102 Duroplex®
T110 Plexture®
A
FRESCO 2™
T108
HIGH PERFORMANCE INTERIOR COATING
DESCRIPTION



An interior, one part,
water-base, high-solids
paint-like coating
consisting of high
strength inorganic
micro aggregates in a
high adhesion matrix of
pure acrylic resin.
Use it for color change
®
on Duroplex or
®
Plexture . When used
over Duroplex, it will
add an additional 5
years to the Duroplex
warranty.
When used over
Plexture, Fresco will
maintain the original
Plexture warranty.
MOLD/MILDEW RESISTANT
FRESCO coating is formulated
with minimal digestible
compounds and contains a long
term, highly effective nontoxic,
fungicide. Incubator tests
prove it is far more resistant to
organisms than paint.
APPLICATION
Applies directly to any clean,
sound, unpainted common
construction substrate. Great
on drywall; superb on concrete
and masonry. Apply with 3/8”
roller or by spray. If by roller, it
may require multiple coats to
achieve opacity. Spray may be
either conventional or airless.
See application instructions for
suggested air pressure and tip
sizes for spraying.
Thinning Instructions: adding
up to 1 quart of clean water per
5 gallon pail of FRESCO 2 is
acceptable to adjust viscosity.
DESIGN OPTIONS
Solid colors or multi-colored
speckle. Choose from our 80
standard colors. Custom color
matching available for
reasonable minimum volume.
LIMITED WARRANTY
Triarch warrants this product for
ten (10) years against defects
in materials at the time of
purchase and to perform as
for specific wording, exclusions,
proper application procedures
Triarch does not warrant the
Triarch liable for consequential
damages. Triarch expressly
disclaims all other implied
warranties, including implied
warranties of merchantability
and fitness for a particular
purpose. Warranty claims will
not be honored unless Triarch
has the opportunity to inspect
the problem area of the incident
undertaken. Triarch offers
Triarch for extended warranty
requirements.
PRODUCT DATA
SPECIFICATIONS








Waterbase pure acrylic
resin
VOC: ASTM 6886
27.03 g/l
Integral and colorfast
pigments
Pencil Hardness 5B
64.5% solids by volume
17 perms ASTM D1653
Film Thickness: 4 mils dry,
6 mils wet
Coverage: 240 square feet
per gallon, less on rough
surfaces.
Triarch
One Energy Way
800-537-6111
www.triarchinc.com
Rev: 12/19/2013
©Triarch 2007
1
REFORMIT™
T116
DRY MIX, POLYMER-MODIFIED, CEMENTITIOUS, FIBER - REINFORCED, LEVELING COAT
DESCRIPTION
High-performance, fiber-reinforced,
dry mix, polymer-modified cement
coat used for leveling and
smoothing of masonry or solid
cementitious substrates on either
interior or exterior walls.
Specifically formulated for use with
Triarch finish systems.
USES
REFORMIT is used to float
irregular wall surfaces, such as
concrete, CMU and other masonry
to achieve a level and acceptable
substrate for the application of
finish materials. The polymer
modified cement supports a wider
temperature curing range than
straight water based materials and
will typically fill minor holes in one
application.
ADVANTAGES
•
Wide application temperature
range
•
Water resistant when cured
•
Rapid build and fill reduces
labor.
COVERAGE
Approximately 55 - 120 ft2 (5.1 –
11.1 m2) of surface area per 50 lb.
(22.7 kg) bag, depending on wall
conditions, application techniques,
etc.
PROPERTIES
Working Time
After mixing, the working time of
the REFORMIT mixture is
approximately 1 to 1 1/2 hours,
depending on ambient temperature
conditions.
Drying Time
Drying time of the REFORMIT
mixture is dependent on the air
temperature and relative humidity.
Under average drying conditions of
700F [21 °C] and
55% R.H, the REFORMIT mixture
will dry in 24 hours.
©Triarch 2008
If exterior, protect work from rain
for at least 24 hours. Full cure is
achieved in 28 days.
Testing Information
For individual test data on this
product's properties, refer to the
chart included with this document.
FOR COMPLETE APPLICATION
INSTRUCTIONS, REFER TO THE
APPROPRIATE TRIARCH
SYSTEM APPLICATION
INSTRUCTIONS.
Job Conditions
Air and surface temperatures for
application of the REFORMIT
mixture must be at
40 °F (4 °C) or higher and must
remain so for a minimum of
24 hours.
Temporary Protection
Shall be provided to protect wall
surface from incidental damage or
weather.
Acceptable Substrates
Unglazed brick, cement plaster,
concrete, or masonry
Surface Preparation
Surfaces must be above 40 °F
(4 °C) and must be clean, dry,
structurally sound and free of
efflorescence, grease, oil, form
release agents and curing
compounds.
MIXING
Pail Mixing
One 50 lb. (22.7 kg) bag of
REFORMIT will produce
approximately 5 gallons (19 L) of
REFORMIT mixture. Add 6-7
quarts (5.7 - 6.6 L) of clean potable
water into a clean plastic container.
Add the REFORMIT slowly while
constantly mixing with a "Twister"
paddle or equivalent mixing blade,
powered by a ½ inch drill (12.7
mm) drill, at 500-1200 rpm. NOTE:
A minimum 7 amp drill works
best for Portland cement based
1
cement based materials.
Thoroughly mix until uniformly
wetted, adjusting consistency with
a small amount of water or
REFORMIT. Allow the material to
set for 10 minutes then re-temper,
adding a small amount of water if
necessary. Material must be free
of lumps before using.
Mortar Mixer – Add 6-7 quarts (5.7
- 6.6 L) of clean potable water for
each 50 lb. [22.7 kg] bag of
REFORMIT into a clean mortar
mixer. Add the REFORMIT while
the mixer is running. Let mix 3 to 5
minutes, shut the mixer off for
10 minutes, then run mixer for
another 2 to 3 minutes to break the
set adding a small amount of water
if necessary to adjust workability.
APPLICATION
Leveling Coat
After proper surface preparation
and materials have been properly
mixed, apply by trowel or texture
pump as needed. Trowel to a level
and smooth render. Repeat
application as needed to achieve a
level substrate to receive finish
materials. REFORMIT can be
applied at maximum ¼” and at a
minimum 25 mil thickness in a
single pass, as required to properly
smooth the wall.
Clean Up
Clean tools with water while the
REFORMIT mixture is still wet.
•
50 pound bags (22.7 Kg)
•
Protect from moisture and
weather & store off the ground
in a cool dry location out of
direct sunlight.
•
If the REFORMIT is warm or
hot, the pot life of the
REFORMIT mixture will be
reduced.
•
The shelf life is
1 year from date of
REFORMIT
T116
manufacture when properly
stored in unopened bags.
CAUTIONS AND LIMITATIONS
•
Clean cool potable water may
be added to adjust workability.
Do not overwater. Warm water
will accelerate the set
•
Mixing paddles and pails must
be clean. Contamination from
previous mixing will lead to a
shorter pot life.
•
Substrate and air temperatures
must be 40 °F (4 °C) or higher
and rising at time of
•
•
of application.
Wear protective eyewear and
clothing since the product
contains cement, which can
cause irritation.
Avoid working in direct sunlight
and keep mixed REFORMIT in
the shade.
TECHNICAL AND FIELD
SERVICES
Available on request
REFORMIT Testing
Criteria
Test
Test Method
Surface Burning
Characteristics
ASTM E 84
Water Vapor
Transmission
Accelerated Weathering
ASTM E 96 Procedure B
Freeze-Thaw
Resistance
ASTM E 2485 (formerly EIMA
101.01)
ASTM E 2485/ICC-ES Proc:
ICC ES (AC219*)
ASTM D 2247
Water Resistance
ASTM G 23 (Carbon Arc)
Tensile Bond2
ASTM C 297/E 2134
(formerly EIMA 101.03)
Water Penetration
ASTM E 331
Flame Spread <25
Smoke Developed <450
ICC: Vapor Permeable
No ANSI/EIMA Criteria
ICC: 2000 hours: No deleterious
effects1
ANSI/EIMA 99-A-2001
60 cycles: No deleterious effects1
No deleterious effects1 after 10
cycles
14 days: No deleterious effects1
Minimum 104 kPa (15 psi) –
substrate or insulation failure
No water penetration beyond the
inner-most plane of the wall after 2
hours at 299 Pa (6.24 psf)
Results
Passed
63 Perms
2000 hours: No
deleterious effects1
effects1
Passed – No deleterious
effects1 after 10 cycles
effects1
>104 kPa (15 psi)
Passed 2 hours at
299 Pa (6.24 psf)
1. No cracking, checking, rusting, crazing, erosion, blistering, peeling, or delamination when viewed under 5x magnification.
Triarch Systems, Inc.
P.O. Box 1014
One Energy Way
(800) 556-7752
www.Triarch.com
©Triarch 2008
and specifications for the installation of Triarch products as of the date
of publication of this document and is presented in good faith. Triarch
engineering, or workmanship of any project. To ensure that you are
purpose.
2
®
Acrylic Glaze™
T117
CLEAR ACRYLIC SURFACE PROTECTOR
DESCRIPTION
Acrylic Glaze is a 100% acrylic
emulsion binder that dries to a
clear appearance and helps
prevent liquid water that is not
under pressure from being
absorbed into the substrate. It
has excellent resistance to
water whitening after fully dried,
reduces dirt pickup, and
improves washability while
revitalizing the color of
weathered finishes.
USES - INTERIOR
Provides a partial seal for new
installations of Duroplex and
Plexture to provide increased
resistance to dirt pickup.
Improves “washability” by
reducing porosity and providing
a clear surface barrier for dirt.
USES – EXTERIOR
•
On older exterior
installations, Acrylic Glaze
revitalizes the color of
weathered Duroplex-EXT
and extends the life cycle,
while reducing porosity.
Provides a surface barrier
to continued attack by acid
rain and other pollutants.
Improves the freeze-thaw
resistance of porous
exterior surfaces by
lowering water absorption.
•
Also works well to reduce
porosity of other building
materials such as stone,
terra cotta, stucco, EIFS
and concrete. Not
recommended for use on
wearing horizontal surfaces
such as concrete decks or
on immersion surfaces
such as pools, hot tubs,
and whirlpools.
COVERAGE
•
The coverage of the 5
gallon (40 lb/18 kg) pail
depends on the texture and
porosity of the substrate.
Printed in USA
©Triarch 2008
•
•
For applications to new
installations of Duroplex or
Plexture, the coverage is
approximately 1200-1600
ft2 (110-150 m2) per coat
per 5 gallon pail.
For use over older Duroplex
or other porous material,
the coverage is reduced to
approximately 500- 1000 ft2
(37-110 m2) per coat per 5
gallon pail.
Porous Material
Concrete and stucco surfaces
must be fully cured a minimum
of 28 days prior to application of
Acrylic Glaze. Concrete and
masonry surfaces may be
slightly dampened prior to
application of Acrylic Glaze.
Mixing
Stir thoroughly before using and
often during the application
process.
PROPERTIES
Drying time
The drying time of Acrylic Glaze
is dependent upon the air
temperature and relative
humidity. Under average drying
conditions of 70o F {21 °C},
55% R.H., Acrylic Glaze is dry
to touch in 2 hours. If exterior,
protect work from rain for at
least 24 hours.
Job Conditions
application of Acrylic Glaze
must be 50 °F (10 °C) or higher
and must remain so for a
minimum of 24 hours.
Surface Preparation
All surfaces must be clean, dry,
structurally sound and free of
efflorescence, grease, oil,
mildew, algae, form release
agents and curing compounds.
Protect adjacent surfaces,
windows, shrubs, etc. from
drips.
New installations of Duroplex
or Plexture
Allow finish to dry a minimum of
24 hours under average drying
conditions [21 °C (70 °F), 55%
R.H.] before applying Acrylic
Glaze.
1
Application
The preferred method of
application is by spray. Suitable
spray equipment is airless
spray or low-pressure hand
pump garden-type sprayer.
Brush, roller, or paint pads can
be used but are prone to
dripping. Always start at the top
of the wall surface and, using
horizontal strokes, saturate the
surface to the point of run-off.
Acrylic Glaze goes on as a
milky white liquid, ensuring
complete coverage, and dries
clear. Do all applications across
a wall section or panel in a
continuous pattern, without
breaks, maintaining a wet edge
until a logical break is reached.
Ensure application is uniform
without runs or excessive
buildup in reveals, special
shapes, etc. Remove excess
Acrylic Glaze with a brush,
roller or cloth.
Clean Up
Clean tools with water while
Acrylic Glaze is still wet.
MAINTENANCE
All Triarch products are
designed to be virtually
maintenance free. However, as
with all building products,
depending on location, some
cleaning may be required.
Five gallon pails weighing 40
lbs. Acrylic Glaze must be
stored at 50 °F (10 °C) or above
in tightly sealed containers out
of direct sunlight.
TRIARCH
One Energy Way
(800) 537-6111
www.triarchinc.com
Printed in USA
©Triarch 2008
CAUTIONS AND
LIMITATIONS
Do not apply if weather
conditions will not permit
complete drying of material
before onset of rain, dew, fog,
or freezing temperatures. Do
not apply to surfaces in direct
sunlight or surfaces over 95 °F
(35 °C).
WARRANTY
Acrylic Glaze has an express
one-year limited material
warranty. Triarch makes no
other warranty expressed or
implied. Certain limitations and
restrictions apply. Contact
Triarch for full details.
Triarch products as of the date of publication of this document
and is presented in good faith. Triarch assumes no liability,
expressed or implied, as to the architecture, engineering, or
workmanship of any project. To ensure that you are using the
latest, most complete information, contact Triarch. Triarch
expressly disclaims all implied warranties, including without
limitation, implied warranties of merchantability and fitness for
a particular purpose.
2
®
PolyGlaz®
T121
CLEAR URETHANE SURFACE PROTECTOR
MIXING
DESCRIPTION
PolyGlaz is a low VOC,
water based, clear
aliphatic urethane that
imparts certain
performance
characteristics to almost
any substrate. Primary
characteristics gained by
the use of PolyGlaz are:
high abrasion resistance,
high UV resistance,
improved gloss levels,
resistance to marking and
ease of repeated cleaning.
Other characteristics
include high microbial
resistance, including
molds and mildews, and a
very low perm rating (0.8),
which may be desired for
certain type of
applications when a
sealed surface is desired.
USES - INTERIOR
Provides a sealed surface
for installations of
Duroplex®, Plexture®,
Klondike™ and Collection
of Joy.™ Benefits include
increased resistance to
dirt pickup, scratch
resistance, and improved
cleanability. Improves
“washability” with a low
perm rating and provides
a smooth, clear surface
barrier for dirt.
Revision 05/28/2012
Printed in USA
©Triarch 2008
PolyGlaz has a perm
rating of 0.8 perms. It is
ideal for use around food
preparation areas and
walls that will be wiped
and cleaned regularly.
COVERAGE
•
•
The coverage of
PolyGlaz depends on
the texture and
porosity of the
substrate.
Applications over a
smooth substrate will
achieve up to 400
square feet per gallon.
For applications over
an absorbent and
textured substrate
such as Duroplex or
Plexture, the coverage
is approximately 14001600 ft2 (110-150 m2)
per coat per 5 gallon
pail.
PROPERTIES
Adhesion:
excellent
VOC:
45 g/l
LEED IEQ 4.2 compliant
Microbial Resistance: 10(best)
Perm (1coat): 0.8 perms
Dry to touch: 20 mins
Complete dry: 24 hours
QUV Exposure: no change
1
Before using, stir with a
clean mixing paddle at low
speed for 1 minute. Do not
entrain air into the
material.
SUBSTRATE
CONSIDERATIONS
Air and surface
temperature for
application of PolyGlaz
must be 50 °F (10 °C) or
higher and must remain
so for a minimum of 24
hours.
Surface Preparation
All surfaces must be
clean, dry, and free of
efflorescence, grease, oil,
mildew, algae, form
release agents and curing
compounds. Since
PolyGlaz is a sealer, be
certain to allow any freshly
painted substrate to cure
before the application of
PolyGlaz. When going
over a new painted
surface, typically a wait
time of 48-72 hours is
required for the water
based paint to adequately
cure before the application
of PolyGlaz. Protect
adjacent surfaces,
windows, shrubs, etc.
from drips.
New installations of
Duroplex or Plexture
Allow substrate finish to
dry a minimum of 48
hours under average
drying conditions [21 °C
(70 °F), 55% R.H.] before
applying PolyGlaz.
Porous Material
Concrete and stucco
surfaces must be fully
cured a minimum of 28
days prior to application of
PolyGlaz.
APPLICATION
dripping. Always start at
the top of the wall surface.
Apply all applications
across a wall section or
panel in a continuous
pattern, without breaks,
maintaining a wet edge
until a logical break is
reached. Ensure
application is uniform
without runs or excessive
buildup. Exercise care
around reveals, special
shapes, etc. Remove
excess material
immediately with a brush,
roller or cloth.
depending upon
installation location, some
cleaning may be required.
SHIPPING AND
STORAGE
Five gallons 45 lbs.
One gallon
9 lbs.
PolyGlaz must be stored
at 50 °F (10 °C) or above
in properly sealed
containers and out of
direct sunlight.
WARRANTY
May be spray applied or
by 3/16” nap roller. If
spraying, where NIOSH
approved particle mask.
Suitable spray equipment
is HVLP or airless spray.
Brush, or paint pads can
be used but are prone to
directional movement or
Second coats will further
reduce perm rating and
provide more protection.
CLEAN UP
Clean tools with water
while PolyGlaz is still wet.
MAINTENANCE
All Triarch products are
designed to be virtually
maintenance free.
However, as with all
building products and
TRIARCH
One Energy Way
(800) 537-6111
www.triarchinc.com
Revision 05/28/2012
Printed in USA
©Triarch 2008
PolyGlaz has a one-year
limited material warranty.
Triarch makes no other
warranty expressed or
implied. Certain limitations
and restrictions apply.
Contact Triarch or our
website for full warranty
for details.
RELATED DOCUMENTS
Specifications
Triarch products as of the date of publication of this document
and is presented in good faith. Triarch assumes no liability,
expressed or implied, as to the architecture, engineering, or
workmanship of any project. To ensure that you are using the
latest, most complete information, contact Triarch. Triarch
expressly disclaims all implied warranties, including without
limitation, implied warranties of merchantability and fitness for
a particular purpose.
2
T311
®
Block Filler
T123
HI-PERFORMANCE FILLER FOR MASONRY
DESCRIPTION
APPLICATION:
Hi-Performance Block Filler is
acrylic resin block filler for use
on interior or exterior masonry,
including concrete block
(CMU), porous brick, poured in
place and precast concrete.
Characteristics are:
Hi-Performance Block Filler is
ready-to-spray and does not
require thinning. Mix material
prior to use with box paddle
and power drill. Apply by brush,
roller, or spray. While wet,
force material into pinhole
surface by back rolling or
trowel to produce a smooth
surface. Two coats will provide
the most uniform surface.









Excellent moisture
resistance
High filling
Low odor, low VOC
Breathable
Mold/mildew resistant
Finish: flat
Color: off white
VOC: 11.45 grams/liter
Hardness:
5B
RECOMMENDED SPREAD
RATE
Min
Wet mils
Dry
Sq ft/gal
Max
15
10
103
ENVIRONMENTAL
Temperature: min: 55F (13 C)
Max: 100F (30C)
Relative humidity: 85% max.
If applying exterior, protect from
rain for 48 hours.
DRY TIME
APPLICATION TIPS
Apply using cross hatch spray
method with 50% overlap to
achieve uniform coverage,
immediately back-roll with ½”
nap roller cover.
Airless Spray
Pressure
Tip size:
Reduction
+/- 2000 psi
517-519
not needed
Drying time is effected by
temperature and humidity. Dry
to touch over new CMU,
approximately (1) hour at 70 F.
CLEAN UP AND HANDLING
Packaging:
5 gallon pails
Weight:
68 lbs.
Do not stack more than 3 high.
Use warm water for clean up.
If needed: 1 qt clean water per
5 gallons
30
19.3
53.5
SURFACE PREPERATION
APPLICATION BEST
PRACITICES
Apply by airless and back-roll
to push material into all minor
pinholes.
Surface must be clean, dry,
and in sound condition.
Remove all oil, dust, grease,
dirt, loose rust, and other
foreign material to insure
adequate adhesion.
RELATED MATERIALS &
DOCUMENTS
SKIMM – acrylic leveling
compound, data page T101
REFORMIT – acrylic modified
Portland cement leveling
compound data page T116
800-537-6111
.triarchinc.
Triarch
One Energy Way
©Triarch 2007
using the latest, most complete
1 information, contact Triarch. Triarch
purpose.
Reinforcing Anti-Cracking Mesh™ (RAC Mesh)
T126
Coverage
Description
An open-weave glass fiber
fabric chemically treated for
compatibility with other system
components.
Uses: When embedded into a
base coat of either SKIMM® or
REFORMIT™, the glass fiber
reinforcing mesh provides ultra
high resistance to cracking and
increases impact resistance of
the wall assembly.
RAC Mesh: Specially coated
for long-term alkali resistance.
Shall weigh a minimum of
0.169 kg/m2 (5 oz/yd2) and
have a minimum tensile
strength of 3.88 kg/cm (225
lbs/in) of width.
Precut RAC Mesh:
Corner Mesh: Recommended
for additional impact resistance
and for clean, crisp arises;
outside corners, and
prefabricated panels. Shall
weigh a minimum of .24
2
2
kg/m (7.2 oz/yd ) and have a
minimum tensile strength of 4.9
kg/cm (274 lbs/in) of width.
RAC Mesh measures 48” wide
by 150 linear feet long. This is
enough RAC Mesh for 600
square feet. The reinforcing
meshes are lapped a minimum
of 2½” at all edges. A layer of
RAC Mesh must be applied
over the entire wall using
published application methods.
Corner Mesh: 9 ¼ inches wide
x 150 lineal feet. (Blue in Color)
Application Procedure
Apply SKIMM or REFORMIT
to the entire surface of the
substrate to form a base coat.
Fully embed the reinforcing
fabric in the wet base coat,
troweling from the center to the
edge of the reinforcing fabric so
as to avoid wrinkles. The
reinforcing fabric shall be
continuous at all corners and
lapped or butted in accordance
with Triarch’s project
recommendations. The overall
minimum base coat thickness
shall be sufficient to fully
embed the mesh. The
recommended method is to
apply the base coat in two
applications. After it cures
(minimum 24 hours), examine
for mesh projections. Correct
as needed to cover the RAC
Mesh. Apply finish coat system.
 Shipped in four foot long
rolls
Clean Up
Dispose of any cuttings in
environmentally acceptable
way and in accordance with
local laws.
RELATED DOCUMENTS
 SKIMM data page T101
 REFORMIT data page T116
 Installers Manual
Please contact Triarch for more
details.
* TRIARCH DOES NOT WARRANT, GUARANTEE OR ASSUME LIABILITY FOR THE WORKMANSHIP OF THE APPLICATOR
Triarch
One Energy Way
800-537-6111
www.triarchinc.com
Printed in USA 07/2013
©Triarch 2008
purpose.

QA Binder Documents Contractor`s Introductory Package

Transcription

Similar documents

harmony

Product Manual

Accura® Amethyst

compresor nebulizador pingüino compresseur nébuliseur penguin

eclipse

LDI - Enviroleather: California and Montana

ru-200 roofing underlayment - WaterBlock® Building Systems

Free Casino Games For Mobile Phones Slot Machine Repair

Energy Hog?

Swatchcard - National Office Furniture