ROBO-668

Transcription

ROBO-668
Dual CPU Full-size SBC
ACTI-777
Dual Pentium III processor based SBC with Intel Graphics and Enthernet
ROBO-667
Dual FC-PGA2 processor based SBC with AGP VGA and Fast Ethernet
ROBO-668
Dual Socket 370 processor based SBC with on-board AGP VGA and fast Ethernet
ACTI-688
Dual Pentium III processor based SBC with ISA64
Single CPU Full-size SBC
ROBO-8710VLA
Pentium 4 processor based SBC with on-board VGA/panel display, LAN and audio
ROBO-679
FC-PGA2 processor based SBC with fast Ethernet, Intel DVMT Display and Ultra 160 SCSI
ROBO-678
Pentium III or Celeron processor based SBC with dual fast Ethernet
ROBO-698
Pentium III or Celeron processor based SBC with on-board AGP VGA
ACTI-648L
Pentium III processor based SBC with on-board AGP VGA
NC-6060
Best Cost/Performance Pentium III processor based SBC with VGA/LAN
ROBO-658
FC-PGA processor based SBC with AGP display, Ethernet and Ultra 160 SCSI
ROBO-638
Pentium III processor based SBC with Ultra 2 SCSI AGP VGA and Ethernet
ROBO-608
Socket 370 processor based SBC with PCI VGA and panel display
ROBO-598VS
Pentium processor based SBC with flash disk
Half-size SBC
ROBO-616
Pentium III or Celeron processor based SBC with 3D direct AGP VGA, fast Ethernet and audio
ROBO-605
Pentium III or Celeron processor based SBC with PCI VGA, Panel Dispaly and ISA Bus
ROBO-505
Pentium processor based SBC with Panel VGA Display and Ethernet
Extension Board
ROBO-U160
U160 SCSI Extension Module with Portwell OmniPCI™ Connection Interface
ROBO-N100
Fast Ethernet Extension Module with Portwell OmniPCI™ Connection Interface
Embedded Board
ROBO-603
5.25" Pentium III or Celeron processor based Embedded Board with 2D/3D Graphics, dual fast
Ethernet and Audio
ROBO-503
3.5" NS GX1 processor based Embedded Board with CRT/LCD, dual Ethernet and Audio
Custom Products
ROBO-8611VG
64Bit PICMG SBC, Based on FC-PGA/FC-PGA2 Processor with PCI VGA, Gigabit Ethernet
ROBO-8610VL
Advanced PICMG SBC, Based on the Intel ® FC-PGA2 Processor with High Performance AGPx2
VGA and Fast Ethernet integrated
NC-6011J
PCI SBC, Based on FC-PGA or FC-PGA2 Processor, Support Dual CRT, AGP 4X 2D/3D
Graphics, Audio and Fast Ethernet Integrated
1
ACTI-777
The Most Advanced PICMG SBC, Based on Dual Intel ® Pentium ® III Processors
with Intel Graphics and Ethernet Solutions (RIMM Memory Supported)
◆
Support dual Socket 370 Pentium® III
(FC-PGA) processor with 100MHz FSB
up to 850MHz
◆
Support two channel RDRAM memory
up to 2GB
◆
Support C&T 69000 chips
◆
On board Intel® 82559 10/100 Base-T
Ethernet
CPU
◆
Support one or two Intel® Pentium ® III
processors for the PGA370 Socket
Chipset
◆
Intel® i840 AGPset, including
- 82840 memory controller hub (MCH)
- 82801 I/O controller hub (ICH)
- 82802 firmware hub (FWH)
Memory
◆
Two 184-pin RIMM sockets with max.
1GB capacity
◆
Support Ultra DMA33/66 IDE mode
◆
PCI Bus spec V2.1 compliant
BIOS
◆
Full-size all-in-one SBC with PICMG 1.0
Rev 2.0 compliant
On-Board I/O
◆
◆
Reserve space around IDE interface
connector to fit DOM (Disk-On-Module)
◆
Fully support ATX function with WOL,
Modem-Ring On, K/B & Mouse wake-up
◆
ISA64 driving capability
◆
Hardware monitoring and watchdog timer
for system protection
Additional Functionality
Specifications
◆
Award BIOS-Plug-n-Play compatible
Support two EIDE channels up to four
HDDs (Ultra DMA 33/66) 2S/1P, two
USB ports* and one IrDA infrared port
Integrated Graphics Controller
C&T 69000 Video display chipset
Adopt PCI interface, built-in 2MB VRAM
◆ DB15 connector at the rear panel
◆ Support display resolution up to
1280x1024,256 colors
◆
◆
Ethernet 10/100 Controller
Intel® 82559 PCI fast Ethernet controller
RJ-45 connector at the rear panel
◆ Support IEEE 802.3 auto-negotiation
algorithm of full-duplex and half-duplex
operation for 10Mb/s and 100Mb/s (NWAY)
◆
◆
DiskOnChip Flash Disk
◆
Support M-Systems' flash disk up to
288MB
System Hardware Monitor
Winbond super I/O is used to monitor
supply voltages to user programmable
voltage levels within 16 mV
◆ Separately monitor up to three fan
tachometer inputs for rotation speeds
and three temperatures sense via two
thermistors circuit
◆ Beep alarms for failed fan out, over/under
voltage of DC voltages, and over
temperature threshold
◆
Watchdog Timer
Watchdog timeout period programmable
via S/W from 0.5 to 254.5 sec./min.
◆ Can be enabled/disabled by jumper setting
◆
PS/2 Mouse
◆
◆
Routed to 6-pin mini-DIN on rear bracket
Shared 6-pin mini-DIN connector with
K/B (Auto-swap)
Power Requirement
"*" Only one USB port available when
◆
installed into standard chassis
+5V@10A (typ.),+12V@300mA,
-12V@30mA
Board Dimension
338.5(L) x 129(W) mm
13.33"(L) x 5.1"(W)
◆ 8-layer PCB
◆
◆
Operating Temperature
◆
ACTI-777
The most advanced PICMG SBC based
on dual Intel® Pentium® III processors
with Intel® graphics and Ethernet
solutions (RIMM memory supported)
0 to +55˚C
Storage Temperature
◆
Ordering Guide
-20 to +75˚C
2
ROBO-667
Feature
Feature
Reliable design for high speed dual Intel®
Pentium® III processors
VIA Pro133T chipset delivers high
performance on the Socket 370 platform
Advanced PICMG SBC with AGP VGA and Ethernet, Based
on the Dual Pentium® III (FC-PGA2) Processors
Specifications
CPU
PGA370 socket dual Intel® Pentium® III processors
System Bus Frequency 100/133 MHz PSB
Chipset
VIA VT82C694T, VT82C686B chipset
Memory
- Up to 1.5GB PC100/133 SDRAM on three 168-pin DIMM sockets
PC100/133 MHz SDRAM for cost effective high
volume memory support up to 1.5GB
BIOS
ATI Mobility with up to 8MB memory for highquality video to eliminate the need for a PCI
video card, saving a PCI slot and additional
expense
On-Board I/O
On-board Intel 10BASE-T/100BASE-TX Fast
Ethernet for high speed data transfers
Standard features for embedded system, like
H/W monitoring, WDT, SSD and Wake-on-LAN
Proprietary PCI daughter board connector for
expansion
Additional Functionality
Display
Ethernet
Solid State Disk
SCSI
- ATI Mobility M1 AGP VGA
- 8MB display memory
- DSUB-15 VGA connector
- Display resolution up to 1280x1024
32-bits colors at refresh rates 85Hz
- 10BASE-T/100BASE-TX Ethernet
- IEEE 802.3u auto-negotiation support
- One RJ-45 connector
- Modem-Ring-On and Wake-On-LAN
DOC socket for up to 288MB
Adaptec AIC 7892 single channel Ultra
160 SCSI controller (optional)
Watchdog Timer
PS/2 K/B & Mouse
Daughterboard
Expansion
ISA Bus
Hardware Monitor
ATX Power Control
Power Consumption
Board Dimension
Operating temperature
Storage temperature
Relative Humidity
Approval
- ECC support
- Award BIOS
- 512KB flash ROM for ease of upgrade
- Support for four EIDE devices with Ultra DMA/100
- Up to two floppy disk drives
- Floppy drive controller for 1.44/1.2MB floppy drives
- Two 16C550 compatible serial ports, one parallel, one IrDA and three
USB ports
Programmable via software from 0.5 sec to 254.5 min
- One mini-DIN 6-pin connector for keyboard and mouse
- One 5-pin header for external keyboard connection
Proprietary PCI connection interface
64mA high driving ISA bus interface to backplane for legacy ISA slots
System monitor (fan, temperature, voltage)
ATX function with 4-pin header connect to backplane
+5V@15A, [email protected]
338.5(L) x122(W) mm; 13.33"x(L) x 4.8"(W)
0 to 55˚C
-20 to +75˚C
5% to 95%, non-condensing
FCC, CE class A
Ordering Guide
ROBO-667
Dual Pentium® III or Pentium III-S processor based SBC with AGP VGA and Ethernet
ROBO-668
Advanced PICMG SBC with On-Board AGP VGA, Fast Ethernet ,
Based on the Dual Socket 370 Processor
Additional Functionality
Specifications
◆
SupportIntel ® Pentium® III or Celeron™
processor with 66/100MHZ FSB
CPU
◆
◆
Single or dual processors
◆
Support C&T 69000 chips
◆ Intel®
82440BX chipset
Chipset
◆
◆
Support up to 1GB of SDRAM memory
with ECC function
C&T 69000 AGP VGA display with 2MB
SDRAM
◆
Intel® 82559 Fast Ethernet
◆
Proprietary PCI connector for expansion
(optional daughter board provided, such
as Ultra 160 SCSI or fast Ethernet)
◆
Two EIDE, two serial port, parallel port,
two USB ports
◆
Watchdog Timer
◆
System hardware monitoring
◆
Full-size all-in-one SBC with PICMG 1.0
Rev 2.0 compliant
Intel ® 82440 BX chipset
Memory
◆
◆
One or dual Socket 370 Intel® Pentium® III
or Celeron™processors up to 850MHZ
Four 168-pin DIMM sockets support up
to 1GB of PC-100 SDRAM
BIOS
◆
AMI system BIOS (256KB flash ROM)
On-Board I/O
◆
On-board Winbond W83977ATF super
I/O with two USB ports*
Watchdog Timer
◆
Watchdog timeout period programmable
via S/W from 0.5 to 254.5 sec./min.
PS/2 Keyboard/Mouse
Single 6-pin mini-DIN Keyboard/mouse
connector on rear bracket
◆ One additional 5-pin header connector
for external keyboard connection through
Portwell Backplane
◆
Power Requirement
◆
+5V@10A,+12V@80mA, -12V@20mA
Board Dimension
◆
Fully PCI Bus spec. V2.1 compliant
339.5(L) x 122(W) mm
13.36"(L) x 4.8"(W)
◆ 8-layer PCB
◆
On board AGP Graphics
C&T 69000 Video display chipset
Built-in 2MB display Cache
◆ DSUB-15 VGA connector
◆ Support display resolution up to
1280x1024, 256 colors
◆
◆
On-board Fast 10/100 Base-T Ethernet
Intel® 82559 PCI fast Ethernet controller
RJ-45 connector at the rear panel
◆ Support IEEE 802.3 auto-negotiation
algorithm of full-duplex and half-duplex
operation for 10Mb/s and 100Mb/s (NWAY)
◆
◆
Ultra 160 SCSI (Optional)
◆
Adaptec AIC 7892 single channel Ultra
160 SCSI controller
DiskOnChip Flash Disk
◆
Support M-Systems' DOC up to 288MB
ISA64 ISA-bus Driving Capability
◆
Support 64mA high driving capability for
ISA-bus slot on Backplane
System Hardware Monitor
On-board temperature and voltages
monitoring
◆ Beep alarms for failed fan out, over/under
voltage of DC voltages, and over
temperature threshold
◆
◆
◆
ISA64 driving capability
Operating Temperature
"*" Only one USB port available when
installed into standard chassis
◆
0 to +55˚C
Storage Temperature
◆
-20 to +75˚C
Relative Humidity
◆
3
5% to 95%, non-condensing
Ordering Guide
ROBO-668
Advanced PICMG SBC with on-board
AGP VGA, Fast Ethernet , based on the
dual Socket 370 processor
ACTI-688
Advanced PICMG Dual-processor SBC with ISA64, Based on the Pentium ® III Processor
◆
Support dual Pentium® III processors for
the SC242 up to 850MHz
◆
Support up to 1GB (max.) of SDRAM with
ECC function
◆
Full-sized all-in-one SBC with PICMG 1.0
Rev. 2.0 compliance
◆
PCI Bus spec. V2.1 compliant
◆
PC '98 & Year 2000 compliant
◆
ISA64 driving capability
◆
Support DOC, DOM (Disk-On-Module)
and ATX function
Specifications
CPU
◆
Support dual Intel® Pentium® III processors
up to 850MHz
Chipset
◆
Intel® 82440BX AGPset
Memory
◆
Four 168-pin DIMM sockets support up
to 1GB (max.) of 3.3V SDRAM with ECC
function
BIOS
◆
AMI system BIOS
(128/256KB flash ROM)
On-Board I/O
◆
On-board Winbond W83977ATF super
I/O with two USB ports
Additional Functionality
DiskOnChip Flash Disk
Reserve socket for DiskOnChip up to
288MB flash disk size
◆ Compact Windows NT can be built into
the 16MB DOC for booting the system
◆
ISA64 ISA-bus Driving Capability
◆
Support 64mA high driving capability for
ISA-bus slot on backplane
System Hardware Monitoring (LM79)
◆
Monitor CPU & chassis fan status,
system temperature and DC voltage
Wake-On-LAN & Modem-Ring-On
Support ATX function with 4-pin header
to connect to backplane
◆ Standby 3-pin header to support LAN card
◆
Watchdog Timer
◆
8 time intervals from 0.5 sec. to 64 sec.
by jumper setting or 255 intervals from
0.5 min. to 254.5 min. by software
programming
Power Requirement
◆
+5V@15A (typ.),+12V@100mA,
-12V@20mA
Ordering Guide
ACTI-688
Advanced PICMG Dual-processor SBC
with ISA64, based on the Intel® Pentium® III
processor
Board Dimension
339.5(L) x 122(W) mm
13.37"(L) x 4.8"(W)
◆ 8-layer PCB (Double-sided component)
◆
◆
Operating Temperature
◆
0 to +55˚C
Connector
Support Mini DIN, 5-pin header & PS/2
type keyboard connector
◆ Support external power connector
◆
4
ROBO-8710VLA
Feature
Feature
Reliable design for higher speed Intel®
Pentium® 4 processor
Intel® 845 chipset, backed up by Intel® EID's
long product life support
High speed mainstream DDR SDRAM memory
Highly Integrated PICMG SBC, Based on
Socket 478 Pentium® 4 Processor with
DDR SDRAM, AGP 4X VGA, Fast Ethernet
and Audio
Specifications
CPU
mPGA478 socket Intel® Pentium® 4 processor
System Bus Frequency 400 MHz PSB
Chipset
- Intel® 845, Intel® MCH and ICH2
Memory
ECC function for data sensitive application
ATI M6 3D graphics controller supports
versatile interfaces for most of image process
transaction terminals and panel display
system applications
BIOS
On-Board I/O
High integration input/output function, such
as high driving digital I/O and SMbus
Standard features for embedded system, like
H/W monitoring, WDT, SSD and Wake-on-LAN
Additional external power connector for stand
alone operation for rugged embedded system
design
Watchdog Timer
PS/2 K/B & Mouse
Daughterboard
Expansion
ISA Bus
Hardware Monitor
ATX Power Control
Power Consumption
Dimension
Operating temperature
Storage temperature
Relative Humidity
Approval
- ATI Mobility M6 3D graphics controller
- Up to 2GB 2.5V 200/266MHz DDR SDRAM on two 184-pin DIMM
sockets
- ECC support
- Award BIOS
- 4Mb flash ROM for ease of upgrade
- Support for four EIDE devices with Ultra DMA/33/66/100
- Up to two floppy disk drivers
- Two serial, one parallel, one IrDA and three USB ports
- 8 high driving GPIO (4 GPI, 4GPO)
Programmable via software from 0.5 sec to 254.5 min
- One mini-DIN 6-pin connector for keyboard and mouse
- One 5-pin header for external keyboard connection
Proprietary PCI connection interface
64mA high driving ISA bus interface to backplane for legacy ISA slots
System monitor (fan, temperature, voltage)
ATX function with 4-pin header connect to backplane
- Two external power connectors (CPU power and system power)
for stand alone operation
338.5(L) x122(W) mm; 13.33"x(L) x 4.8"(W)
0 to 60˚C
-20 to +80˚C
5% to 90%, non-condensing
FCC, CE class A
Ordering Guide
Additional Functionality
ROBO-8710VLA
Display
Socket 478 Pentium® 4 processor based PICMG SBC
with DDR SDRAM, AGP 4X VGA, Fast Ethernet and
audio
Ethernet
Audio
Solid State Disk
SCSI
- ATI Mobility M6 graphics controller
- 16MB DDR SDRAM display memory
- TMDS/LVDS Interface support
- Dual view support
- TV-out
- 10BASE-T/100BASE-TX Ethernet
- IEEE 802.3u auto-negotiation support
- One RJ-45 connector with two LED indicators for LAN access and
link status
- Modem-RIng-On and Wake-On-LAN
AC '97 2.0 audio
DOC socket for up to 288MB
Adaptec AIC 7892 single channel Ultra 160 SCSI controller (optional)
ROBO-679
Feature
Feature
Reliable design for high speed FC-PGA2
Intel® Pentium® III or Celeron® processor
Intel® 815E chipset, backed up by Intel® EID's
long product life support
PC100/133 MHz SDRAM for cost effective
memory support
DVMT and 4MB external display memory enable
optimum system memory utilization for
maximum 2D/3D graphics performance
through Direct AGP
On-board Intel® 10BASE-T/100BASE-TX Fast
Ethernet for high speed data transfers
Standard features for embedded system, like
H/W monitoring, WDT, SSD and Wake-on-LAN
Proprietary PCI daughter board connector for
expansion
Highly Integrated SBC with VGA and Ethernet, Based on the
Intel® Pentium® III (FG-PGA2) or Celeron® Processor
Specifications
CPU
PGA370 Socket Intel® Celeron® or Pentium® III (FC-PGA2) processors
System Bus Frequency 66/100/133 MHz PSB
Chipset
Intel® 815E chipset
Memory
Up to 512MB PC100/133 SDRAM on two 168-pin DIMM sockets
BIOS
Award BIOS
On-Board I/O
- Support for four PCI Bus Master EIDE devices with Ultra
Watchdog Timer
PS/2 K/B & Mouse
Daughterboard
Expansion
ISA Bus
Hardware Monitor
ATX Power Control
Power Consumption
Board Dimension
Operating temperature
Storage temperature
Relative Humidity
Approval
DMA/33/66/100
- Up to two floppy disk drives
- Two serial, one parallel, one IrDA and three USB ports
Programmable via software from 0.5 sec to 254.5 min
- One mini-DIN 6-pin connector for keyboard and mouse
- One 5-pin header for external keyboard connection
Proprietary PCI connection interface
64mA high driivig ISA bus interface to backplane for legacy ISA slots
System monitor (fan, temperature, voltage)
ATX function with 4-pin header connect to backplane
+5V@10A (typ.), +12V@200mA, -12V@30mA
338.5(L) x122(W) mm; 13.33"x(L) x 4.8"(W)
0 to 55˚C
-20 to +75˚C
5% to 90%, non-condensing
FCC, CE class A
Ordering Guide
Additional Functionality
ROBO-679
Display
FC-PGA2 Pemtium® III or Celeron® processor based
SBC with DVMT display and Ethernet
Ethernet
Solid State Disk
SCSI
Specifications are subject to change without notice.
Celeron®, Pentium® III and Pentium® 4 are registered trademarks of Intel Corporation.
Other trademarks, logos, brands and company names are the property of their respective owners.
- Intel® DVMT (Integrated 3D)
- 4MB display memory
- Display resolution up to 1600x1200, 256 colors at refresh rates 85Hz
- 10BASE-T/100BASE-TX Ethernet
- IEEE 802.3u auto-negotiation support
- One RJ-45 connector
- Modem-Ring-On and Wake-On-LAN
DOC socket for up to 288MB
Adaptec AIC 7892 single channel Ultra 160 SCSI controller (optional)
ROBO-678
Highly integrated SBC with Dual Fast Ethernet, Intel ® DVMT Display and Ultra 160 SCSI,
Based on the Intel® Pentium ® III or Celeron™ Processor
◆
◆
SupportIntel ® Pentium® III or Celeron™
processor with FSB up to 133MHz, special
space reserved for high performance
Pentium® III processor
Support PC100/133 SDRAM memory up
to 512MB (max.)
Specifications
CPU
◆
Intel® Pentium® III or Celeron™processor
for PGA 370 socket
Chipset
◆
Intel® 815E chipset
Memory
◆
On-board dual 10/100 Base-T Ethernet
◆
Integrated 3D graphic controller (DVMT,
4Mbyte display memory)
BIOS
Support two DMA33/66/100 IDE
On-Board I/O
◆
◆
◆
◆
◆
Compliant with PCI Bus spec V2.1
◆
Full-size all-in-one SBC with PICMG 1.0
Rev 2.0 compliant
◆
Proprietary PCI connector for expansion
(optional daughter board provided, such
as Ultra 160 SCSI or fast Ethernet)
◆
Reserve space around IDE interface
connector to fit DOM (Disk-On-Module)
and socket 370 for easy installation of
higher speed processor
◆
Support ATX function with WOL, ModemRing On, K/B & Mouse wake-up
◆
ISA64 driving capability
◆
Hardware monitoring & Watchdog Timer
for system protection
"*" Only one USB port available when
installed into standard chassis
Two 168-pin DIMM sockets support up
to 512MB of PC-100/133 SDRAM
Award system BIOS (512KB flash ROM)
On-board Winbond W83627HF super
I/O with two USB ports*
Parallel Port
◆
Single parallel port controller with
bi-directional capability
Additional Functionality
Integrated Graphics Controller
Intel® DVMT ( Integrated 3D)
4MB display memory
◆ Support display resolution up to
1600x1200, 256 colors at refresh rates
85Hz
◆
◆
Dual Ethernet 10/100 Controller
◆
Ultra 160 SCSI (Optional)
◆
Watchdog timeout period programmable
via software from 0.5 sec to 254.5 min.
◆ Can be enabled/disabled by jumper
Real Time Clock
◆
◆
Up to 7 years of battery backup protection
An external Li Battery
PS/2 Keyboard/Mouse
◆
Share PS/2 keyboard 6-pin mini-DIN on
rear bracket
Power Requirement
◆
+5V@7A, +12V@200mA, -12V@20mA
Board Dimension
338.5(L) x 122(W) mm
13.3"(L) x 4.8"(W)
◆ 6-layer PCB
◆
Adaptec AIC 7892 single channel Ultra
160 SCSI controller
DiskOnChip Flash Disk
◆
Support M-Systems' DOC up to 288MB
ISA64 ISA-bus Driving Capability
◆
Watchdog Timer
◆
Intel® 82559 PCI fast Ethernet controller
and ICH2 embedded MAC controller
Support 64mA high driving capability for
ISA-bus slot on Backplane
System Hardware Monitor
On-board temperature and voltages
monitoring
◆ Beep alarms for failed fan out, over/under
voltage of DC voltages, and over
temperature threshold
◆
Ordering Guide
ROBO-678
Highly integrated SBC with dual fast
Ethernet, based on the Intel® Pentium® III
or Celeron™processor
◆
ROBO-678N
Operating Temperature
Highly integrated SBC with single fast
Ethernet, based on the Intel® Pentium® III
or Celeron™processor
◆
0 to +55˚C
Storage Temperature
◆
-20 to +75˚C
Relative Humidity
◆
5% to 95%, non-condensing
ROBO-678W
Highly integrated SBC without fast
Ethernet, based on the Intel® Pentium® III
or Celeron™processor
4
ROBO-698
Highly integrated PICMG AIO SBC, Based on the Intel ® Pentium ® III or Celeron™ Processor
◆
Intel® 440BX AGPset supports
66/100MHz FSB for Socket 370 SBC type
Pentium® III processor up to 850MHz or
Celeron™ processors up to 700MHz
◆
On-board AGP VGA with 2MB VRAM
inside and 10/100 Base-T Ethernet
◆
On-board 4 DIMM sockets support up to
1GB of system memory with ECC function
◆
Socket 370 type processors are more
rugged than traditional Slot 1 Pentium® III
processors
Specifications
CPU
On-board VGA
Support Intel ® Socket 370 type
Pentium ® III processor up to 850MHz
◆ Support Intel ® Celeron™ processor up
to 700MHz
◆
◆
Chipset
◆
PC '98, PICMG 1.0 Rev 2.0 and PCI V2.1
industrial standard compliant
◆
One DOC socket for booting Windows
NT directly
◆
Adopt DS1687 RTC to support real
Y2K compliance
Intel® 82440BX AGPset
Memory
◆
Four 168-pin DIMM sockets support up
to 1GB of SDRAM with ECC function
BIOS
◆
◆
AMI system BIOS (256KB flash ROM)
Intel® C&T 69000 chipset with built-in
2MB SDRAM
◆ Support display mode up to resolution
1280x1024 and refresh rate 60Hz
◆ Support TFT/DSTN flat panel or CRT
display simultaneously
On-Board 10/100 Base-T Ethernet
◆
◆
On-board Winbond W83977ATF super
I/O with two USB ports and one IrDA
infrared port
◆
System monitoring and protection
8 time intervals from 0.5 sec. to 64 sec.
by jumper setting or 255 intervals from
0.5 min. to 254.5 min. by software
programming
Power Requirement
◆
+5V@6A (typ.),+12V@140mA,
-12V@30mA
Board Dimension
338.5(L) x 122(W) mm
13.33"(L) x 4.8"(W)
◆ 6-layer PCB
◆
◆
Built with Intel® 82559 Ethernet chip to
support 10/100 Base-T connecting
capability
DiskOnChip Flash Disk
◆
On-Board I/O
Watchdog Timer
◆
Additional Functionality
Support M-Systems' flash memory disk
up to 288MB
ISA64 ISA-bus Driving Capability
◆
Support 64mA high driving capability for
ISA-bus slot on backplane
ATX Power Control
◆
Modem-Ring-On and Wake-On-LAN
Ordering Guide
ROBO-698
Highly integrated PICMG AIO SBC, based
on the Intel® Pentium® III or Celeron™
processor with VGA display and 10/100
Base-T Ethernet
Operating Temperature
◆
0 to +55˚C
Storage Temperature
◆
-20 to +75˚C
Connector
◆
Support Mini DIN, 5-pin header & PS/2
type keyboard connector
6
ACTI-648L
Advanced PICMG SBC with On-board AGP VGA, Based on the Pentium ® III Processor
◆
Support dual Pentium® III processors for
the SC242 up to 850MHz
◆
Support up to 512MB (max.) of SDRAM
with ECC function
◆
Support AGP VGA/Panel display up to
2MB VRAM
◆
Full-sized all-in-one SBC with PICMG
2.0 compliance
◆
PCI Bus spec. V2.1 compliant
Specifications
CPU
◆
Support dual Intel® Pentium® III processors
up to 850MHz
Chipset
◆
Intel® 82440BX AGPset
Memory
◆
Two 168-pin DIMM sockets support up
to 512MB (max.) of 3.3V SDRAM with
ECC function
BIOS
◆
PC '98 & Year 2000 compliant
◆
ISA64 driving capability
◆
◆
All electrolytic capacitors adopt 105°C for
safety consideration
Watchdog Timer
On-Board I/O
On-board Winbond W83977ATF super
I/O and two USB ports
8 time intervals from 0.5 sec. to 64 sec.
by jumper setting or 255 intervals from
0.5 min. to 254.5 min. by software
programming
Power Requirement
◆
+5V@10A (typ.),+12V@80mA,
-12V@20mA
Board Dimension
339.5(L) x 122(W) mm
◆ 13.37"(L) x 4.8"(W)
◆ 8-layer PCB (Single-sided component)
◆
Operating Temperature
◆
0 to +55˚C
Connector
Support Mini DIN, 5-pin header & PS/2
type keyboard connector
◆ Support external power connector
◆
5
Optional On-board VGA
Intel ® C&T 69000 chipset with built-in
2MB SDRAM
◆ Adopt AGP interface
◆ Support display mode up to resolution
1280x1024 and refresh rate 60Hz
◆ Support TFT/DSTN flat panel or CRT
display simultaneously
◆
ISA64 ISA-bus Driving Capability
◆
AMI system BIOS (256KB flash ROM)
◆
◆
Additional Functionality
Support 64mA high driving capability for
ISA-bus slot on backplane
System Hardware Monitoring (LM79)
◆
Monitor CPU & chassis fan status,
system temperature and DC voltage
Wake-On-LAN & Modem-Ring-On
Support ATX function with 4-pin header
to connect to backplane
◆ Standby 3-pin header to support LAN card
◆
Ordering Guide
ACTI-648L
Pentium® III processor based PICMG SBC
with on-board AGP VGA and normal
capacitor for cost saving
NC-6060
Feature
Feature
Reliable design for Intel® Pentium® III or
Celeron® processor
VIA PLE133 chipset delivers excellent levels
of scalability and performance on a costeffective, integrated chipset platform with
high graphics integration
PC100/133 MHz SDRAM for cost effective
memory support
VIA 2D/3D AGP VGA with up to shared 8MB
display memory for high-quality integrated
video
On-board RealTek 8139C Fast Ethernet
provides economic network connection
Standard features for embedded system, like
H/W monitoring, WDT and SSD
Proprietary PCI daughter board connector for
expansion
Best Cost/Performance PICMG SBC with AGP VGA and Fast
Ethernet, Based on Intel® Pentium® III or Celeron® Processor
Specifications
CPU
PGA370 socket Intel® Pentium® III or Celeron® processor
System Bus Frequency 66/100/133 MHz PSB
Chipset
VIA PLE133 chipset
Memory
Up to 1GB PC/VCM 100/133 SDRAM on three 168-pin DIMM sockets
BIOS
- AMI BIOS with PC '98 support
On-Board I/O
Watchdog Timer
PS/2 K/B & Mouse
ISA Bus
Hardware Monitor
ATX Power Control
Power Consumption
Dimension
Operating temperature
Storage temperature
Relative Humidity
Approval
- 256KB flash ROM for ease of upgrade
- Support for four EIDE devices with Ultra DMA/66/100
- Up to two floppy disk drives
- Two 16C550 compatible serial ports, one parallel, one IrDA and two
USB ports
Adjustable via hardware jumper setting from 0.5 sec. to 64 sec.
- One mini-DIN 6-pin connector for keyboard and mouse
- One 5-pin header ffor external keyboard connection
64mA high driving ISA bus interface to backplane for legacy ISA slots
System monitor (fan, temperature, voltage)
ATX function with 4-pin header connect to backplane
+5V@8A, +12V@150mA, -12V @20mA
338.5(L) x 122(W) mm ; 13.33"(L) x 4.8"(W)
0 to 55˚C
-20 to +75˚C
5% to 95%, non-condensing
FCC, CE class A
Ordering Guide
Additional Functionality
NC-6060
Display
Pemtium® III or Celeron® processor based SBC with
AGP VGA and Ethernet
Ethernet
Solid State Disk
- VIA 2D/3D AGP VGA
- Shared 8MB display memory
- Display resolution up to 1280x1024, 256 colors at refresh rates 60Hz
- RealTek 8139C PCI Ethernet
- IEEE 802.3x auto-negotiation support
- One RJ-45 connector
- Modem-Ring-On and Wake-On-LAN
DOC socket for up to 288MB
ROBO-658
World's First Fully Integrated SBC with AGP VGA Display, 10/100 Base-T Ethernet
and Ultra 160 SCSI Functions
◆
The most advanced SBC built with AGP
display, 10/100 Base-T Ethernet and
Ultra 160 SCSI
◆
Support Socket 370 type Pentium® III up
to 850MHz or Celeron™ processors up to
700MHz
◆
Support FSB up to 100MHz
◆
Support up to 512MB (max.) of SDRAM
Specifications
CPU
Support Intel ® Pentium® III processor
up to 850MHz
◆ Support Intel ® Celeron™ processor up
to 700MHz
◆
Chipset
◆
Memory
◆
◆
Intel®
◆
On-board Adaptec 7892 Ultra 160 SCSI
◆
Support 2D/3D graphics display with
4 MB SDRAM
◆
◆
◆
◆
82559 10/100 Base-T Ethernet
Ultra DMA33/66 IDE mode and ISA64
driving capability
Full-size AIO SBC with PICMG 1.0 Rev
2.0 and PCI Bus spec V2.1 compliant
Reserve space around IDE interface
connector to fit DOM (DiskOnModule)
Support ATX function with WOL,
Modem-Ring On, K/B & Mouse wake-up
◆
Support 4MB Video display cache
memory
◆
One DOC socket support up to 288MB of
flash memory disk
◆
Hardware monitoring and watchdog
timer for system protection
Two 168-pin DIMM sockets support up
to 512MB of SDRAM
BIOS
◆
AMI system BIOS
Integrated Graphics Controller
2D graphics display resolution up to
1600x1200
◆ Full 2D H/W acceleration, 100MHz
SDRAM interface
◆ Support 4MB SDRAM with 3D hyper
pipelined architecture
◆
On-Board 10/100 Base-T Ethernet
◆
◆
Support two EIDE channels up to four
HDDs (Ultra DMA 33/66) 2S/1P, two USB
ports and one IrDA infrared port
◆
Software programmable (0.5, 1.5, 2.5,...
~254.5 seconds and 0.5, 1.5, 2.5, ......
~254.5 minutes)
Power Requirement
◆
+5V@6A (typ.),+12V@100mA,
-12V@30mA
Board Dimension
Adaptec AIC 7892 SCSI controller to
support Ultra 160 SCSI transfer rate up
to 160MB/s
DiskOnChip Flash Disk
◆
Watchdog Timer
◆
Built with Intel® 82559 Ethernet chip to
support 10/100 Base-T connecting
capability
On-Board Ultra 160 SCSI
On-Board I/O
Support M-Systems' flash disk up to
288MB
Fully ATX Power Control
◆
Modem-Ring-On, K/B & mouse
wake-up, WOL and suspend to RAM
Ordering Guide
ROBO-658
338.5(L) x 122(W) mm
13.33"(L) x 4.8"(W)
◆ 6-layer PCB
Best performance PICMG AIO SBC with
VGA, Ethernet and SCSI, based on the
Pentium® III or Celeron™ processor
Operating Temperature
ROBO-658Z
◆
◆
◆
0 to +55˚C
Storage Temperature
◆
-20 to +75˚C
Connector
◆
7
Intel® i810E AGPset
Additional Functionality
Support Mini DIN, 5-pin header & PS/2
type keyboard connector
ROBO-658 without SCSI function
ROBO-658W
ROBO-658Z without Ethernet function
ROBO-638
Full Function SBC with Ultra 2 SCSI, AGP VGA/Ethernet, Based on the Pentium ® III Processor
◆
Support Intel® Pentium® III processors for
the SC242 up to 850MHz
◆
Intel® 440BX AGPset supports up to 1GB
of SDRAM with 100MHz memory bus
and ECC function
Specifications
CPU
◆
Adopt flush mounted Slot 1 CPU
architecture to make the board more
rugged and reliable
◆
On-board ATI Rage Pro AGP VGA
display with 4MB/8MB VRAM
On-board Intel® 82558 10/100 Base-T
Ethernet
◆
◆
◆
One DOC socket for booting Windows
NT directly
◆
256KB/512KB SDRAM built-in L2 cache
inside the embedded module with a
Pentium® III processor
◆
Adopt DS1687 RTC to support real Y2K
compliance
◆
Support system monitoring & protection,
and ATX power control
AMI system BIOS (256KB flash ROM)
On-Board I/O
Adaptec 7890 Ultra 2 SCSI, the fastest
disk I/O for 80MB/S
PC '98, PICMG 1.0 Rev. 2.0 and PCI V2.1
industrial standard compliant
◆
On board Winbond W83977ATF super
I/O with two USB ports and one IrDA
infrared port
Watchdog Timer
Eight segment (0.5, 1, 2, 4, 8, 16, 32,
64 seconds) hardware time-out intervals
◆ 255 intervals from 0.5 min to 254.5 min
by software programming
◆
Power Requirement
◆
+5V@9A (typical), +12V@100mA,
-12V@30mA
Board Dimension
339.5(L) x 122(W) mm
◆ 13.37"(L) x 4.8"(W)
◆ 8-layer PCB
On-board ATI Rage Pro graphics
accelerator supports industry leading 3D
and top grade 2D display performance/
quality
On-Board 10/100 Base-T Ethernet
◆
Four 168-pin DIMM sockets support up
to 1GB of SDRAM with ECC function
BIOS
◆
◆
Intel ® 82440BX AGPset with MMX™
technology and optimized SDRAM
Memory
◆
◆
On-board AGP VGA Display
Chipset
◆
◆
Support Intel ® Pentium® III processors
up to 850MHz
Additional Functionality
Built with Intel® 82558 Ethernet chip to
support 10/100 Base-T connecting
capability
On-Board Ultra 2 SCSI
Adaptec AIC 7890A SCSI controller to
support Ultra 2 SCSI transfer rate up to
80MB/s
◆ 15 devices connectivity
◆ Drivers supported: DOS, Windows 95,
Windows NT, Novell Netware, SCO
Unix, OS/2 Warp 3.0, ... etc
◆
System Hardware Monitoring (LM79)
◆
Monitor CPU & chassis fan status,
system temperature and DC voltage
DiskOnChip Flash Disk
◆
Support M-Systems' flash disk up to
288MB
Fully ATX Power Control
◆
Modem-Ring-On and Wake-On-LAN
◆
Operating Temperature
◆
0 to +55˚C
Connector
◆
Support Mini DIN, 5-pin header & PS/2
type keyboard connector
Ordering Guide
ROBO-638
Full function PCI/ISA AIO SBC, based on
the Pentium® III processor
ROBO-638Z
ROBO-638 without SCSI function
ROBO-608
Best Cost/Performance S-370 Type PICMG SBC with PCI VGA/Panel Display
◆
◆
Intel® 440BX AGPset support 66/100MHz
FSB for Socket 370 Pentium® III processor
up to 850MHz or Celeron™ processor
up to 700MHz
Support up to 1GB(max.) of registered
SDRAM with ECC function
Specifications
CPU
Support Intel® Socket 370 type
Pentium® III processor up to 850MHz
◆ Celeron™ processor up to 700MHz
◆
Chipset
◆
◆
◆
◆
PC104 connector and high ISA-bus
driving capability
BIOS
Memory
◆
◆
Intel® 82440BX AGPset
One DOC socket supports up to 288MB
of flash memory disk
Support C&T 69000 PCI VGA display
with optional panel solution
◆
Adopt DS 1687 RTC to support real Y2K
compliance
◆
Support system overheat protection, real
H/W Y2K compliant RTC and ATX power
control
Four 168-pin DIMM sockets support up
to 1GB of SDRAM with ECC function
AMI system BIOS (256KB flash ROM)
On-Board I/O
◆
On-board Winbond W83977ATF super
I/O with two USB ports and one IrDA
infrared port
Watchdog Timer
Eight time intervals from 0.5 sec. to
64 sec. by jumper setting
◆ 255 intervals from 0.5min to 254.5min
by software programming
Additional Functionality
On-Board PCI VGA Display
C&T 69000 high performance flat
panel/CRT HiQVideo accelerator with
2MB integrated memory
◆ Support TFT/DSTN flat panel or CRT
display simultaneously
◆
DiskOnChip Flash Disk
◆
Support M-Systems' flash memory disk
up to 288MB
System Monitoring/Protection
◆
Auto speeds down when CPU overheats
(OS independent & driverless)
Fully ATX Power Control
◆
Modem-Ring-On and Wake-On-LAN
Ordering Guide
◆
Power Requirement
◆
+5V@6A (typ.),+12V@140mA,
-12V@30mA
ROBO-608
Advanced Socket 370 PICMG SBC with
PCI VGA
ROBO-608V
Advanced Socket 370 PICMG SBC
without PCI VGA
Board Dimension
LCD-KIT-RS
338.5(L) x 122(W) mm
◆ 13.33"(L) x 4.8"(W)
◆ 6-layer PCB
Optional kit for TFT SVGA LCD panel
◆
LCD-KIT-RX
Optional kit for XGA LCD panel
Operating Temperature
◆
0 to +55˚C
Storage Temperature
◆
-20 to +75˚C
Connector
Support Mini DIN, 5-pin header & PS/2
type keyboard connector
◆ Support external power connector
◆ Support optional panel display port
◆
8
ROBO-U160
U160 SCSI Extension Module with Portwell
OmniPCI™ Connection Interface
ROBO-U160 is a daughter board for Portwell
SBCs with special PCI connection interface. (like
ROBO-668, ROBO-678) and more It provides
additional high performance SCSI Ultra 160/m
function to Single Board Computers.
This module can be factory optional item or an
additional item for customer's order later on. The
board is based on Adaptec AIC 7892 U160/m
SCSI controller. Designed in the most compact
form factor makes this board taking minimum
space upon the SBC.
All in all, ROBO-U160 is a flexible item for more
versatile factory configuration or an additional addon module for function extension.
ROBO-N100
Fast Ethernet Extension Module with
Portwell OmniPCI™ Connection Interface
ROBO-N100 is daughter board for Portwell SBCs
with special PCI connection interface. (ROBO-668,
ROBO-678) It provides additional high
performance fast Ethernet function to Single Board
Computers.
This module can be factory optional item or an
additional item for customer's order later on. The
board is based on Intel 82559 fast Ethernet
controller. It is designed in the most compact form
factor, which makes this board taking the minimum
space upon the SBC.
All in all, ROBO-N100 is a flexible item for more
versatile factory configuration or an additional addon module for function extension.
5
◆
Adaptec AIC7892 SCSI Ultra 160 SCSI controller
◆
Compact sized
◆
Proprietary PCI connector for piggy back (board to
board) connection
◆
Fully PCI Bus spec. V2.1 compliant
◆
68-pin SCSI connector located at PCBA component side
◆
Support SCSI Ultra160 SCSI
◆
Single channel
◆
With 68-pin LVDS SCSI cable
◆
Dimension: 77(L) x 54(W) mm
◆
Intel® 82559
◆
Compact sized
◆
Proprietary PCI connector for piggy back
(Board to Board) connection
◆
Fully PCI Bus spec. V2.1 compliant
◆
One Ethernet RJ-45 cable
◆
Support IEEE 802.3
◆
Auto-negotiation algorithm of full-duplex and halfduplex operation for 10Mb/s and 100Mb/s (NWAY)
◆
Dimension: 77(L)x52(W) mm
ROBO-616
All-in-one PICMG Half-size PCI Single Board Computer
◆
Support Intel® Pentium® III or Celeron™
Processor
Specifications
CPU
◆
◆ Intel ®
◆
◆
815E chipset support FSB133
Intel® 815E Direct AGP Graphic with
4MB display cache
Maximum SDRAM memory up to 512MB
(one DIMM socket)
Support Intel® Pentium® III or Celeron™
processor
Chipset
◆
Intel 815E with ICH2
Memory
one 168-pin DIMM socket
Support 3.3V SDRAM up to 512MB
◆ 64/128 Mbit DRAM technology
◆
◆
◆
Support 2 Ultra DMA/33/66/100 IDE
channel
◆
Half length all-in-one SBC, PCI bus
Interface (PCMCIA)
On-Board I/O
Integrated AC-97 2.0 sound blaster
compactible audio
On-board W83627HF super I/O with
two USB, one IrDA Interface
◆ Two Ultra DMA33/66/100 IDE channel
◆
On-board 10/100 Base-TX fast Ethernet
Watchdog Timer
◆
Fully support ATX function with WOL,
Modem-Ring On, K/B & Mouse wake-up
BIOS
◆
Additional Functionality
On-Board VGA Display
◆
Intel 815E GMCH integrated graphic
controller with 4MB display cache
On-board 10/100 Base-TX Ethernet
Intel 82801 BA (ICH2) integrated LAN
controller
◆ Intel 82562ET
◆
System Monitoring/Protection
◆
Monitor CPU and system temperate,
opening voltage and fan status
Award BIOS with PC'98 support
Ordering Guide
◆
◆
◆
ROBO-616
Half-sized PCI SBC with VGA/LAN/
Audio based on Pentium ® III or Celeron™
processor
Support 255 intervals from 0.5sec/min to
245.5 sec/min by software programming
Power Requirement
◆
+5V@7A (typ.),+12V@200mA,
-12V@20mA
Board Dimension
◆
◆
185(L) x 122(W) mm
7.3"(L) x 4.8"(W)
Operating Temperature
◆
0 to +55˚C
Storage Temperature
◆
-20˚C to 75˚C
10
ROBO-605
World's First Half-size SBC, Based on the Intel Pentium III or Celeron Processor
◆
◆
◆
Support Socket 370 processor with
PCI VGA/panel display
Specifications
CPU
Support Intel® Pentium® III or Celeron
processor
Intel 440BX AGPset supports 66/100MHz PSB
◆
Support Intel® Celeron™ processor
up to 600MHz
Chipset
◆
Support Intel® Pentium® III processor
up to 850MHz
◆
All-in-one half-sized SBC with ISA-bus
◆
Support up to 256MB (max.) of 3.3V
SDRAM with ECC function
◆
Intel® 82440BX AGPset with MMX™
technology and optimized SDRAM
Memory
◆
One 168-pin DIMM socket supports up
to 256MB of SDRAM with ECC function
BIOS
◆
AMI system BIOS
On-Board I/O
◆
On-board Winbond W83977ATF super
I/O, two USB ports and one IrDA
infrared port
◆
Support M-Systems' flash disk up to
288MB
◆
Support C&T 69000 PCI VGA
display with optional panel solution
Watchdog Timer
Support system processor overheat
protection and real hardware Y2K
compliant RTC
Power Requirement
◆
◆
◆
Eight segment (0.5, 1, 2, 4, 8, 16, 32,
64 seconds) hardware time-out intervals
[email protected] (typ.),+12V@120mA,
-12V@20mA
Board Dimension
On-Board PCI VGA Display
Intel® C&T 69000 high performance flat
panel/CRT HiQVideo accelerator with
2MB integrated memory
◆ Support TFT/DSTN flat panel or CRT
display simultaneously
◆ Optional kit for SVGA/ XGA LCD panel
◆
DiskOnChip Flash Disk
◆
Support M-Systems' flash memory disk
up to 288MB
System Monitoring/Protection
◆
Auto speeds down when CPU overheats
(OS independent & driverless)
Ordering Guide
ROBO-605
Half-sized SBC with PCI VGA/panel,
based on the Pentium® III or Celeron™
processor
LCD-KIT-RS
Optional kit for TFT SVGA LCD panel
◆
LCD-KIT-RX
◆
Optional kit for XGA LCD panel
185(L) x 122(W) mm
7.3"(L) x 4.8"(W)
◆ 8-layer PCB
Operating Temperature
◆
0 to +55˚C
Connector
Support Mini DIN, 5-pin header & PS/2
type keyboard connector
◆ Support panel display port
◆
11
Additional Functionality
ROBO-505
The Most Compact SBC with Panel/VGA Display and 10/100 Base-T Ethernet, Based
on the Pentium ® Processor
◆
Support Intel® Pentium® (P55C)
processor up to 233MHz; compatible
processor up to 333MHz
Intel ®
Specifications
CPU
On-Board PCI VGA Display
Intel P55C processors up to 233MHz
◆ AMD K6 processors up to 333MHz
◆ Cyrix 6x86MX processors up to 333MHz
Intel® C&T 69000 VGA display chipset
with 2MB VRAM
◆ Support TFT/DSTN flat panel or CRT
display simultaneously
◆ Support display resolution 1280x1024,
color 8bpp and refresh rate 60Hz
◆
◆
Adopt
◆
One DIMM socket supports up to 128MB
of SDRAM
Chipset
◆
On-board 512KB cache memory
Memory
◆
Adopt C&T 69000 VGA/panel display
with 2MB VRAM
◆
Support M-Systems' flash disk up to
288MB
430TX PCI chipset
◆
◆
On-board Realtek 8139A 10/100 Base-T
Ethernet
◆
Four COM ports supported
◆
8-layer PCB
◆
ISA high driving capability and CPU
overheat protection supported
One on-board 168-pin DIMM socket
supports up to 128MB of SDRAM
512KB pipeline burst SRAM
BIOS
AMI PCI/ISA Pentium BIOS
◆
DiskOnChip Flash Disk
◆
Support M-Systems' flash memory disk
up to 288MB
On-Board 10/100 Base-T Ethernet
◆
Built with Realtek 8139 Ethernet chip to
support 10/100 Base-T connecting
capability
On-Board I/O
◆
◆
Intel® 82430TX PCI chipset
Cash Memory
◆
◆
Additional Functionality
On-board Winbond W83977ATF super
I/O with two USB ports
Watchdog Timer
◆
Eight segment (0.5, 1, 2, 4, 8, 16, 32,
64 seconds) hardware time-out intervals
Power Requirement
◆
+5V@5A (typ.),+12V@60mA,
-12V@60mA
Board Dimension
Ordering Guide
ROBO-505
Advanced half-sized AIO SBC with onboard PCI VGA display and 10/100 BaseT Ethernet, based on the Pentium ®
processor
LCD-KIT-RS
Optional kit for TFT SVGA LCD panel
◆
LCD-KIT-RX
◆
Optional kit for XGA LCD panel
185(L) x 122(W) mm
7.3"(L) x 4.8"(W)
◆ 8-layer PCB
Operating Temperature
◆
0 to +55˚C
Storage Temperature
◆
-20 to +75˚C
Relative Humidity
◆
5 to 95% non-condensing
12
ROBO-603
Intel® Socket 370 Celeron™ or Pentium® III Processor Based 5.25" Embedded SBC
with 2D/3D Graphics, Dual Fast Ethernet and Audio
Specifications
◆
Support Intel FC-370 Celeron™ or
Pentium® III processor
CPU
◆
◆
SMI AGP 2X Lynx3DM SM 720 integrated
2D/3D graphics and multimedia
accelerator with embedded 4MB SGRAM
(Optional 8MB)
◆
Support 40-pin video capture port
◆
Dual Intel 82559ER 100Base-TX fast
Ethernets
◆
Support Type II compact flash disk
◆
Integrated AC-97 2.0 sound blaster
compatible audio
Chipset
◆
◆
PC/104 expansion connector
32-bit PCI slot
VIA Apollo Pro 133A, VT82C694X
Memory
◆
◆
Intel® FC-370 Celeron™ or Pentium ® III
(with system bus frequencies of 66/100/
133MHz)
Onboard one 168-pin DIMM socket
supports up to 256MB SDRAM
Cash Memory
◆
512KB pipeline burst SRAM
BIOS
◆
Award 256KB Flash BIOS
On-Board I/O
◆
VT82C686A / Winbond W83977
Watchdog Timer
◆
Generate a system reset, IRQ15 or NMI.
Software selectable time out interval
(32 ~ 254 min., 1 sec./step)
Power Requirement
◆
Flat Panel/CRT Interface
SMI Lynx3DM SM 720, high
performance 128-bit GUI, 3D engine
◆ 4MB of SGRAM frame buffer on
Lynx3DM SM 720
◆ Simultaneously support CRT and flat
panel (EL, LCD and gas plasma)
displays
◆ 2xAGP, accelerator graphics ports 1.0
compliantLCD panel supports up to
800x600 @24 bpp, 1024x768 @24 bpp
◆ CRT displays support up to 800x600 @
24 bpp, 1024x768 @24 bpp
◆
Dual Ethernet Interface
◆ On-board dual Intel 82559ER PCI-bus
Ethernet controllers
◆ PCI 100/10 Mbps, IEEE 802.3U
compatible
◆ For diskless system
Ordering Guide
[email protected], +12V@80mA
Board Dimension
ROBO-603
203(L) x 146(W) mm (3.5" FDD-size)
◆ 8"(L) x 5.75"(W)
Socket 370 based 5.25" Embedded
system board with LCD/CRT, dual
Ethernet, Audio
Operating Temperature
ROBO-603N
◆
0 to +60˚C
◆ 5 to 95% non-condensing
◆
13
Additional Functionality
ROBO-603 with single Ethernet
ROBO-503
NS GX1 Processor Based 3.5" Embedded SBC with CRT/LCD, Dual Ethernet and Audio
Specifications
◆
On-board NS Geode GX1 BGA CPUs
◆
NS Geode CS5530A support CRT and
18-bit TFT panels
◆
3.5" FDD SubCompact form factor
◆
Support type II compact flash disk
◆
Dual Intel® 82559ER 100 Base-TX fast
Ethernet
◆
Integrated AC-97 2.0 sound blaster
compatible audio
◆
5V only operation
◆
PC/104 expansion connector
CPU
Flat Panel / VGA Interface
On-board NS Geode GX1 200/300MHz
(available in different speeds by special
order)
◆ BGA package (Capable to support NS
Geode GXm, GXLV, and GX1)
◆
◆
Chipset
◆
NS Geode CS5530
Memory
◆
On-board one 144pin SODIMM socket
supports up to 256 MB SDRAM
NS CX5530
Shared display memory up to 4MB
◆ Simultaneously display CRT and flat
panel
◆
Dual Ethernet Interface
◆ On-board dual Intel 82559ER PCI-bus
Ethernet controllers
◆ PCI 100/10 Mbps, IEEE 802.3U
compatible
◆ For diskless system
BIOS
◆
Award 256KB FLASH BIOS
On-Board I/O
Winbond W83977F-A
Two RS-232, one Parallel port
◆ Two USB ports, one IrDA interface
Ordering Guide
◆
ROBO-503
◆
NS GX1 processor based 3.5" embedded
system based with CRT/LCD, dual
Ethernet and Audio
Watchdog Timer
◆
Generate a system reset, IRQ15 or NMI.
Software selectable time-out interval
(16 sec. ~ 7666 sec., 30 sec./step)
Power Requirement
◆
[email protected] w/GX1 200MHz
Board Dimension
◆
◆
145(L) x 102(W) mm (3.5" FDD-size)
5.7"(L) x 4.02"(W)
Operating Temperature
◆
0 to +55˚C
Storage Temperature
◆
-20 to +75˚C
Relative Humidity
◆
13
Additional Functionality
5 to 95% non-condensing
ROBO-503N
ROBO-503 with single Ethernet
ROBO-8611VG
64Bit PICMG SBC, Based on FC-PGA/FC-PGA2
Processor with PCI VGA, Gigabit Ethernet
Feature
Feature
Support Intel® FC-PGA/FC-PGA2 Pentium® III or
Celeron® Processor
Socket for M-System DiskOnChip; connected to 26-pin
shrouded header
Single processor with 66/100/133MHz PSB
Two EIDE, two Serial ports, one Parallel port, one IrDA
port and three USB port
Serverworks LC-T and OSB4 chipset
SDRAM memory up to 4GB with ECC function
ATI Rage XL PCI VGA display with 2MB VRAM
Broadcom 5703 Gigabit Ethernet
Support Watchdog Time and ISA64 Driving
Full-size All-In-One SBC with PICMG 1.0 Rev 2.0 compliant
Fully complies with PCI Bus spec. V2.1
Proprietary PCI connector for expansion (optional
daughter board provided, such as Ultra-160 SCSI
ROBO-U160 or fast Ethernet ROBO-N100 )
PCI SBC, Based on FC-PGA or FC-PGA2 Processor, Support Dual
CRT, AGP 4X 2D/3D Graphics, Audio and Fast Ethernet Integrated
NC-6011J
Feature
Feature
Support Intel® FC-PGA & FC-PGA2 Pentium® III or
Celeron® Processor
Single processor with PSB 66/100/133MHz
VIA Pro133T Chipset
Support SDRAM memory up to 512MB with ECC function
AGP x4 Graphics with 8 or 16 MB of display cache
One EIDE, two Serial, one Parallel port, one IrDA port and
three USB ports (One on bracket)
Audio output
Intel® 82559ER PCI Fast Ethernet Controller
Socket for M-System DiskOnChip
GPO 4 Channel (TTL signal)
Watchdog Timer
System hardware monitoring
PCI only half-size All-In-One SBC with PICMG 1.0 Rev2.0
compliant
One St
in Com
ead
mu
Ah
ations!
nic
ep
Fully complies with PCI Bus spec. V2.1
Portwell, Inc.
Headquarter
3F, No. 92, Nei-Hu Rd., Sec. 1,
114 Taipei, Taiwan, R.O.C.
Tel: +886-2-27992020
Fax: +886-2-27991010
E-mail: [email protected]
http://www.portwell.com.tw
American Portwell
eMCA (UK) Ltd.
Portwell Japan, Inc.
38507 Cherry St. Suite D,
Newark, CA 94560 USA
Tel: +1-510-790-9192
Fax: +1-510-790-9191
E-mail: [email protected]
http://www.portwell.com
Unit 30, Basepoint Enterprise Centre
Stroudley Road, Basingstoke, Hampshire,
RG24 8UP UK
Tel: +44-1256-406688
Fax: +44-1256-406689
E-mail: [email protected]
http://www.emca.co.uk
¢E101-0042 Ueda Build. 7F, 10-2
Kanda higashi matsushita-cho
chiyoda-ku Tokyo Japan
Tel: +81-3-5298-8071
Fax: +81-3-5298-8072
E-mail: [email protected]
http://www.portwell.co.jp
Single Board Computer
ROBO-8610VL
Advanced PICMG SBC, Based on the Intel® FC-PGA2 Processor
with High Performance AGPx2 VGA and Fast Ethernet integrated
ACTI-777
The Most Advanced PICMG SBC with Intel® Graphics and Ethernet
Solutions (RIMM Memory Supported), Based on the Dual Intel®
Pentium® III Processors
Support Pentium® III or Celeron® (FC-PGA2) processor with
133MHz PSB
■ Support PC133 SDRAM memory up to 1.5GB with ECC function
■ ATI range mobility with 4/8MB VRAM (factory optional)
■ Intel 82559 fast Ethernet controller
■ Proprietary PCI connector for expansion(optional daughter board
provided, such as Ultra 160 SCSI or fast Ethernet)
■ One parallel port, two EIDE, two serial and three USB ports
■ Support Watchdog Timer & system hardware monitoring
■ Full-size all-in-one SBC with PICMG 1.0 Rev 2.0 compliant
■
Support Dual Socket 370 Intel ® Pentium® III (FC-PGA) processor
with 100MHz PSB
■ Support two channel RDRAM memory up to 2GB
■ Support C&T 69000 chip
■ On board Intel 82559 10/100 Base-T Ethernet
■ Support Ultra DMA/33/66 IDE mode
■ Support ATX function with WOL, Modem-Ring On, K/B & Mouse
wake-up
■ ISA64 driving capability
■
ROBO-679
High-integrated SBC with Fast Ethernet, Intel DVMT Display and
Ultra 160 SCSI, Based on the Intel® FC-PGA2 Processor
ROBO-667
Advanced PICMG SBC with High Performance AGP VGA and Fast
Ethernet, Based on the Dual FC-PGA2 Processors
Support Pentium® III or Celeron® (FC-PGA2) processor up to
1.26GHz with 133MHz PSB
■ Support PC100/133 SDRAM memory up to 512MB
■ Integrated 3D graphic controller (DVMT, 4MB display Cache)
■ Support two Ultra DMA/33/66/100 IDE
■ Proprietary PCI connector for expansion (optional)
■ Hardware monitoring & watchdog timer for system protection
■ Support ATX function with WOL, Modem-Ring On, K/B & Mouse
wake-up
■ ISA64 driving capability
■
Support dual Intel Pentium® III (FC-PGA2) processors with
133MHz PSB
■ Support PC133 SDRAM memory up to 1.5GB with ECC function
■ ATI rage mobility 8MB VRAM
■ Intel 82559 fast Ethernet controller
■ Proprietary PCI connector for expansion (optional daughter board
provided, such as Ultra-160 SCSI or fast Ethernet)
■ One parallel port, two EIDE, two serial and three USB ports
■ Support Watchdog Timer & system hardware monitoring
■ Full-size all-in-one SBC with PICMG 1.0 Rev 2.0 compliant
■
ROBO-678
ROBO-668
Advanced PICMG SBC with On-board AGP VGA and Fast Ethernet,
Based on the Dual Socket 370 Processors
High-integrated SBC with Dual Fast Ethernet , Based on the Intel®
Pentium® III or Celeron® Processor
Support Intel® Pentium® III (FC-PGA) or Celeron® processor with
133MHz PSB
■ Support PC100/133 SDRAM memory up to 512MB
■ On-board dual 10/100 Base-T Ethernet
■ Integrated 3D graphic controller (DVMT, 4MB display cache)
■ Support two DMA/33/66/100 IDE
■ Compliant with PCI Bus spec V2.1
■ Proprietary PCI connector for expansion (optional)
■ Support ATX function with WOL, Modem-Ring On, K/B & Mouse
wake-up
■ ISA64 driving capability
■
Pentium®
Celeron®
Support single or dual
III (FC-PGA2) or
(PPGA)processors with 66/100MHz PSB
■ Support C&T 69000 chips and Intel® 82440BX chipset
■ One parallel port, two EIDE, two serial and two USB ports
■ Support SDRAM memory up to 1GB with ECC function
■ C&T 69000 AGP VGA display with 2MB SDRAM
■ Intel® 82559 Fast Ethernet
■ Support Watchdog Timer & system hardware monitoring
■ Proprietary PCI connector for expansion (optional daughter
board provided, such as Ultra 160 SCSI or fast Ethernet)
■
4
Intel ®
PCI & ISA Backplane
PBP-05P
ISA General Description
140mm
170mm
170mm
PBP-03I
PBP-20I
20-slot ISA Passive Backplane
199.4mm
14-slot ISA Passive Backplane
180.5mm
174.6mm
135mm
90mm
170mm
PBP-14I
8-slot ISA Passive Backplane
4-slot ISA Passive Backplane
182mm
PBP-08I
6-slot ISA Passive Backplane
PBP-04I
3-slot ISA Passive Backplane
72mm
4-layer PCB with ground and power planes for reducing noise and keeping lower impedance
Frame Rated PCB at 94-V0
LED power indicator for +5V, +12V, -5V and 12V
Heavy duty terminal block connector for industrial power supply wiring(*)
Equipped with gold-plated socket for good contact
Tantalum capacitor on board to maintain reliable and stable quality
Easy cut for dual or multi system(*)
Plug-in sockets of termination resistors for high speed signal.(*)
"*"means for most part of products
4-slot PCI Passive Backplane
104.08mm
PCI General Description
Compact size back plane for half sized PCI SBC
PICMG 1.0 Rev 2.1 Compliant (PCI golden finger only)
Support AT or ATX type power connector
4 layers PCB with power and ground planes to reduce power noise and keep lower
impedance
Frame rated PCB at 94-V0
User friendly design supporting external K/B connector, power for chassis fan and
power indicator
PBP-06I
PBP-04P
5-slot PCI Passive Backplane
416.7mm
175.3mm
318.9mm
220.6mm
Active PICMG Backplane
ACTI-18AH
2.4mm PCB thickness
ATX power connector support
Fit for any 20-slot chassis
ACTI-14AA
14-Slot (4xPCI) PICMG Backplane
257mm
264.8mm
264.8mm
415.29mm
8
ACTI-14P4
18-Slot (17xPCI) PICMG Backplane
415.29mm
2.4mm PCB thickness
ATX power connector support
Fit for any 20-slot chassis
Best installation for multiple cards
14-Slot (10xPCI) PICMG Backplane
257.18mm
ACTI-19A7
19-Slot (7xPCI) PICMG Backplane
317mm
2.4mm PCB thickness
ATX power connector support
PCI slot ID selectable
Fit for any 14-slot chassis
316.87mm
2.4 mm PCB thickness
ATX power connector support
Fit for any 14-slot chassis
Rack-mount Chassis
IRC-860
19" 6U Rack-mount CTI Chassis
IRC-850
19" 5U Rack-mount CTI Chassis with 10 Drive Bays
IRC-750
19" 5U Rack-mount CTI Chassis with 6 Drive Bays
PRC-4164/PNC-6162
Magic design for wall-mount, desk-top and rack-mount application
RDA-209
19" 4U 9-drive Rack-mount Disk-Array Chassis
RPC-800
19" 4U Rack-mount PC Chassis for 14-Full-length Cards
RPC-600FT
19" 4U Rack-mount Fault Tolerant Server (FTS) Chassis
RPC-520
19" 20-slot 4U Industrial Rack-mount PC Chassis
RPC-520FT
19" 4U Rack-mount Fault Tolerant Server (FTS) Chassis
RPC-500NE
The Most Cost-Effective 19" 4U Rack-mount PC Chassis
RPC-500NP
The Most Cost-effective 19" 4U Rack-mount PC Chassis
RPC-500N/L
The Most Cost-Effective 19" 4U Rack-mount PC Chassis
IRC-305
Advanced 19" 2U Industrial Rack-mount PC Chassis
PRC-2193/2193P
Advanced 19" 2U Industrial Rack-mount PC Chassis
PRC-1234
Compact 19" 1U Industrial Rack-mount Chassis for ATX M/B
PRC-1173
Super Slim 19" 1U Industrial Rack-mount PC Chassis
Rack-mount K/B Drawer
IRC-215N/PIK-215
19" 1U Rack-mount Keyboard Drawer with K/B & Trackball
IRC-210N/PIK-210
19" 1U Rack-mount Keyboard Drawer with 101-key Keyboard
Node Chassis
PNC-5063
Advanced 6-slot Industrial Node Chassis for Half-size PCI Cards
IRC-404S
Compact 4-slot Industrial Node Chassis
IRC-308
8-Slot Full-size Industrial Node Chassis (Shoe-box)
IRC-306
6-Slot Full-size Industrial Node Chassis (Shoe-box)
IRC-306S
6-Slot Industrial Node Chassis with NB CD-ROM, FDD, HDD
IRC-304S
Advanced 4-slot Industrial Node Chassis with NB CD-ROM, FDD, HDD
Accessory
EZDRV-300/200N
5.25" Compact Drive Set with Notebook Type CD-ROM, FDD and space for 2.5" HDD
RMC-214/217
19" Rack-mount Enclosure for 14"/15"/17" Regular Monitor
1
IRC-860
19" 6U Rack-mount CTI Chassis
IRC-860 is an advanced 19" 6U industrial rack-mount
chassis designed specially for CTI (Computer Telephony
Integration) and fault tolerant server applications.
Its rugged & detachable card cage is designed for easy
installation and three 12cm cooling fans for better
General
Construction
Heavy-duty steel with aluminum front
panel
Air Filter
One replaceable filter for boards and
two for drives
Cooling Fan
Three 12cm (86.5cfm) ball-bearing fans
Disk Drive Housing
A type: 2x5.25"+6x3.5";
B type: 4x5.25"+2x3.5"
Card Retainer
Two locations for one card retainer
Card Cage
Removable card cage for easy
installation
PSU Bracket
Replaceable module for PS/2 or PS/2
redundant PSU
Function Panel
Replaceable module for PS/2 or PS/2
redundant PSU
31
◆
4x5.25"+2x3.5" or 2x5.25"+6x3.5" drive
bays for RAID
◆
Three 12cm ball-bearing cooling fans
provide better ventilation for better
system reliability
◆
New rack-mount handle
◆
Detachable card cage for easy
installation and maintenance
◆
Modularized function panel for one, dual
or quad systems
◆
Single PS/2 power supply & dual PS/2
400W+400W redundant PSU installable
◆
Replaceable modularized back panel for
20-/14-slot ISA/PICMG BP or ATX M/B
ventilation. Besides, its design concept to prevent high
temperature from new high-frequency CPUs and to
provide sufficient power source to the system is important
for heavy-loading CTI & new servers to get the best
reliability.
Standard Color
Input Voltage
Beige, black
95 - 132V/185 - 264V Auto-range
Dimension
Input Frequency
482(W) x 495.3(D) x 266(H) mm
19"(W) x 19.5"(D) x 10.5"(H)
47Hz - 63Hz
Input Current
Weight
7A max./115V, 4A max./230V
Net: 22kg (48.4lb)
Gross: 24kg (52.8lb)
Efficiency
Backplane
Min. 70%
MTBF Reliability
20-slot ISA Backplane
20-slot PICMG 4-system BP
19-slot PICMG (18xPCI) active BP
19-slot PICMG (12xPCI) active BP
19-slot PICMG (4xPCI) BP
18-slot PICMG dual-system BP
Environment
Power Supply (ORION-450AX)
0 to +55˚C
Maximum Output
Storage Temperature Range
450W
Output Voltage & Current
+5V@40A, +12V@17A,
+3.3V@28A, [email protected]
[email protected], +5V&+3.3V (max. 225W)
Min. 50,000 hours at 25˚C (70˚F)
Safety
UL/CSA/TUV/FCC/CE
Operating Temperature Range
0 to +70˚C
Relative Humidity
5 to 95% non-condensing
IRC-860
19" 6U Rack-mount CTI Chassis
Features
Benefits
◆
19" 6U rack-mount chassis meets EIA RS-310C standard
◆
Easy to fit in a 19" cabinet from different venders
◆
Extremely compact size ( Only 49.5 cm / 19.5" )
◆
Economic and easy to choose rack-mount cabinet
◆
Modularized function panel for one, dual, quad systems
◆
Easy for installing multiple systems and redundant PSU
◆
Reserve LEDs & beep reset switches for redundant PSU
◆
Easy to keep stock and OEM project
◆
Detachable card cage for easy installation and maintenance
◆
Convenient and economic for system integration
◆
Three 12cm ball-bearing cooling fans
◆
The best ventilation to provide higher system reliability
◆
Two types of drives housing for 4x5.25"+2x3.5" or
2x5.25"+6x3.5" drives
◆
More flexible to integrate varied systems with RAID &
CD-ROM
◆
Replaceable modularized back panel for 20-/14-slot ISA &
PICMG BP or ATX M/B
◆
Flexible choice and easy upgrade of architecture to satisfy
most current and future application requirements
◆
Field replaceable power supply bracket for both normal
PS/2 PSU and dual PS/2 type redundant PSU
◆
Need only 3 minutes to change defective PSU
Only 30 seconds to change defective PSU module
◆
What's New
Detachable card cage
Replaceable back panel for PSUs
IRC-860 is equipped with a detachable
card cage to ease card installation. It is
convenient to link the cables between CPU
cards and devices.
For non-stop operation under CTI systems,
its modularized back panel design help to
install single or dual PS/2 400W + 400W
redundant PSU.
Replaceable back panel for different
Backplanes or ATX motherboard
By changing the modularized back panel,
different 20-slot Backplanes or ATX and
baby AT motherboards can be installed into
IRC-860.
Ordering Guide
IRC-860B-19P4-450AX
19" 6U rack-mount chassis of 4x5.25"+2x3.5" drives with 19-slot
PICMG Backplane and 450W Auto-range ATX power supply
IRC-860B-19P4-3005
19" 6U rack-mount chassis of 4x5.25"+2x3.5" drives with 19-slot
PICMG Backplane and 300W redundant ATX power supply
IRC-860B-19P4-4005
Replaceable function panel
Three modular designed function panels
are available for single , dual and quad
systems display. Any OEM project is
welcome.
19" 6U rack-mount chassis of 4x5.25"+2x3.5" drives with 19-slot
PICMG Backplane and 400W redundant ATX power supply
IRC-860B-MX-450AX
19" 6U rack-mount chassis of 4x5.25"+2x3.5" drives for ATX M/B
with 450W Auto-range ATX power supply
P.S.: "A" means 2x5.25"+6x3.5" drives
"B" means 4x5.25"+2x3.5" drives
32
IRC-850
19" 5U Rack-mount CTI Chassis with 10 Drive Bays
IRC-850 is an advanced 19" 5U Industrial rack-mount
chassis specially for CTI (Computer Te l e p h o n y
Integration) and fault tolerant server applications. Built
with eight 5.25" drive bays (for RAID) and a 800W
(600W+200W) N+1 redundant PSU, it provides reliable
power source to the system and non-crash storage to the
application.
General
Construction
Heavy-duty steel with 8mm aluminum
front panel
Cooling Fan
8x5.25"+1x3.5" (or 1xNB CD-ROM+1xNB
FDD) drives for RAID
◆
3 hot-swap cooling fans for better ventilation
◆
Detachable card cage for easy installation
and maintenance
◆
Dual card retainer positions
◆
Modularized function panel for one, dual
or quad systems
◆
Power On/Off switch protection cap and
touch free reset switch for secure access
◆
800W (600W+200W) N+1 redundant PSU,
suitable for full-loading CTI applications
◆
Modularized back panel, 20-slot BP, babyAT & ATX M/B applicable, especially for
big-AT size M/B
Its rugged and detachable card cage is designed for easy
installation and three 12cm hot-swap cooling fan for better
ventilation. The ways to prevent high temperature from
new high-frequency CPUs and to expand the system
functionality within a limited space are important for
heavy-loading CTI & new servers to get the best
reliability.
Standard Color
Input Voltage
Beige, black
90 - 132V/180 - 264V selectable
Dimension
Input Frequency
482(W) x 673(D) x 220(H) mm
19"(W) x 26.5"(D) x 8.7"(H)
47Hz - 63Hz
Input Current
Three 12cm hot swap ball- bearing fans
Weight
15A max./115V, 8A max./230V
Disk Drive Housing
Net: 25kg (55lb)
Gross: 27kg (59.4lb)
Efficiency
5.25"x8+3.5"x1 (or NB CD-ROMx1+NB
FDDx1)
Card Retainer
Two locations for one card retainer
PSU Bracket
Replaceable module for PS/2 or PS/2
redundant PSU
Function Panel
Modularized function panel for one or
dual systems
Backplane
MTBF Reliability
Environment
Power Supply (ORION-2004)
0 to +55˚C
Maximum Output
Storage Temperature Range
800W
Replaceable module for 20-slot BP or
ATX/Baby AT M/B
Output Voltage & Current
1xModule+1xAlarm+1xBeep Reset
Min. 70%
20-slot ISA BP
20-slot PICMG 4-system BP
19-slot PICMG 18xPCI active BP
19-slot PICMG 12xPCI active BP
19-slot PICMG 4xPCI BP
18-slot PICMG dual-system BP
Back Panel
Redundant PSU Signal
29
◆
+5V@60A, +12V@24A,
+3.3V@48A, [email protected]
-12V@3A, +5V, +12V&+3.3V (max. 550W)
Min. 50,000 hours at 25˚C (70˚F)
Safety
UL/TUV/FCC/CE
Operating Temperature Range
0 to +70˚C
Relative Humidity
5 to 95% non-condensing
IRC-850
19" 5U Rack-mount CTI Chassis with 10 Drive Bays
Features
Benefits
◆
19" 5U rack-mount chassis meets EIA RS-310C standard
◆
Easy to fit in a 19" cabinet from different vendors
◆
Modularized function panel for one, dual, quad systems
◆
Easy for installing multiple systems and redundant PSU
◆
ON/OFF switch protection cap and touch-free reset switch
◆
Avoid accidental reset of system
◆
Detachable card cage for easy installation and maintenance
◆
Convenient for system integration
◆
Two adjustable positions for hold-down card retainers
◆
Fix all the cards more flexibly and tightly
◆
Three 12cm hot-swap ball-bearing cooling fans
◆
The best ventilation to provide higher system reliability
◆
Enhanced drive bracket to hold 8x5.25" + 1x3.5" drives
◆
More flexible to integrate varied systems with RAID &
CD-ROM drives
◆
Changeable modularized back panel for 20-slot ISA & PICMG
BP or ATX M/B
◆
Flexible choice and easy upgrade of architecture to satisfy
most current and future application requirements
◆
800W (600W+200W) N+1 redundant PSU for non-stop computing
◆
Suitable for full-loading CTI applications
What's New
Detachable card cage
Replaceable back panel
800W N+1 (600W redundant) PSU
IRC-850 is equipped with a detachable
card cage to ease card installation. With
this cage, it is convenient to link the cables
between CPU cards and devices.
Only by changing the modularized back
panel, different 20-slot Backplanes or ATX
motherboards can be installed into IRC-850.
To meet the power requirement of CTI
system, IRC-850 is equipped with N+1
redundant PSU for non-stop operation.
Ordering Guide
IRC-850-19P4-2004
19" 5U rack-mount chassis of 8x5.25" drives with
19-slot PICMG Backplane and 600W+ 200W N+1
redundant Auto-range ATX PSU
IRC-850-19AC-2004
19" 5U rack-mount chassis of 8x5.25" drives with
19-slot PICMG (12 x PCI) Backplane and 600W+
200W N+1 redundant Auto-range ATX PSU
IRC-850-MX-2004
19" 5U rack-mount chassis of 8x5.25" drives for
ATX M/B with 600W+ 200W N+1 redundant Autorange ATX PSU
●
Special model for SPARC system board is
also ready for OEM customers
▲ Top View of IRC-850
30
IRC-750
19" 5U Rack-mount CTI Chassis with 6 Drive Bays
IRC-750 is an advanced 19" 5U industrial rack-mount
chassis designed specially for CTI (Computer Telephony
Integration) and fault tolerant server applications.
It's the best choice for installing RAID disk with four 5.25"
drives and also the floppy and CD-ROM drive. Its rugged,
General
Construction
Heavy-duty steel with aluminum front
panel
Air Filter
Enhanced drive bracket to hold 5.25"x4+
3.5"x1 (or 1xNB CD-ROM+1xNB FDD)
drives for RAID
◆
Two 12cm hot-swap ball-bearing cooling
fans provide better ventilation
◆
Dual card retainer positions
◆
Modularized function panel for one, dual
or quad systems
◆
Power On/Off switch protection cap and
touch free reset switch for secure access
◆
PS/2 type redundant PSU installable
◆
ATX M/B applicable, especially for bigAT size M/B
s t u r d y, full-sealed and well-cooled steel chassis is
specially designed to withstand shocks, dust, humidity,
trembling vibration and high operating temperature in the
harsh environment.
Standard Color
Input Voltage
Beige, black
95 - 132V/185 - 264V auto-range
Dimension
Input Frequency
482(W) x 495.3(D) x 221(H) mm
19"(W) x 19.5"(D) x 8.7"(H)
47Hz - 63Hz
Input Current
One replaceable air filter
Weight
7A max./115V, 4A max./230V
Cooling Fan
Net: 19kg (41.8lb)
Gross: 21kg (46.2lb)
Efficiency
Two 12cm (86.5cfm) ball-bearing fans
Disk Drive Housing
5.25"x4+3.5"x1 (or 5.25"x1 NB CDROM+3.5"x1 NB FDD)
Card Retainer
Two locations for one card retainer
PSU Bracket
Replaceable module for PS/2 or PS/2
redundant PSU
Function Panel
Modularized function panel for one or
dual systems
Speaker
One 8Ω speaker
27
◆
Backplane
Min. 70%
14-slot ISA BP
14-slot PICMG 12xPCI active BP
14-slot PICMG 7xPCI active BP
14-slot PICMG 4xPCI BP
13-slot PICMG 4xPCI BP
13-slot PICMG dual-system BP
MTBF Reliability
Power Supply (ORION-450AX)
0 to +55˚C
Maximum Output
Storage Temperature Range
450W
Output Voltage & Current
+5V@40A, +12V@17A,
+3.3V@28A, [email protected]
[email protected], +5V&+3.3V (max. 225W)
Min. 50,000 hours at 25˚C (70˚F)
Safety
UL/CSA/TUV/FCC/CE
Environment
Operating Temperature Range
0 to +70˚C
Relative Humidity
5 to 95% non-condensing
IRC-750
19" 5U Rack-mount CTI Chassis with 6 Drive Bays
Features
Benefits
◆
19" 5U rack-mount chassis meets EIA RS-310C standard
◆
Easy to fit in a 19" cabinet from different vendors
◆
Extremely compact size (only 49.5 cm / 19.5")
◆
Economic and easy to choose rack-mount cabinet
◆
Modularized function panel for one, dual, quad systems
◆
Easy for installing dual systems and redundant PSU
◆
ON/OFF switch protection cap and touch-free reset switch
◆
Avoid accidental reset of system
◆
Two 12cm ball-bearing hot-swap cooling fans
◆
Best ventilation to provide higher system reliability
◆
Enhanced drive bracket to hold 4x5.25" + 1x3.5" drives
◆
More flexible to integrate varied systems with RAID
◆
Two adjustable positions for hold-down card retainer
◆
Fix all the cards more flexibly and tightly
◆
Changeable modularized back panel for 14-/8-slot ISA &
BP, ATX or baby AT M/B
◆
◆
Need only one minute to change the back panel
Easy to change to different PICMG Backplanes and keep stock
Field replaceable power supply bracket for both normal PS/2
PSU and PS/2 type redundant PSU
◆
Need only 3 minutes to change defective PSU
◆
What's New
More drive space for expansion
Two fans for better ventilation
ATX Motherboard
IRC-750 enhances the drives' bracket to
hold up to four 5.25" disk drive and one NB
type floppy and CD-ROM together. It is
easy for you to install a RAID 5 disk array
with best reliability.
IRC-750 is equipped with two ball-bearing
fans to have better ventilation and a
replaceable filter to exclude dusts.
ATX and baby AT type motherboards can
be installed inside IRC-750 just by
changing the modularized back panel.
Ordering Guide
IRC-750-14I-45X
19" 5U rack-mount chassis with 14-slot ISA
Backplane and 450W Auto-range ATX PSU
IRC-750-14P4-45X
19" 5U rack-mount chassis with 14-slot PICMG
BP and 450W Auto-range ATX PSU
IRC-750-14A7-45X
19" 5U rack-mount chassis with 14-slot 7xPCI
PICMG BP and 450W Auto-range ATX PSU
IRC-750-MX-45X
19" 5U rack-mount chassis for ATX M/B with
450W ATX PSU
▲ IRC-750 in black
28
PRC-4164/PNC-6162
Magic 6-slot Node Chassis
▲ PRC-4164
PNC-6162 is a compact and rugged 6-slot full-size node
chassis designed for space limited applications. Its
rugged, sturdy, full-sealed and well-cooled steel chassis is
specially designed to withstand shocks, dust, humidity,
trembling vibration and high operating temperature in the
harsh environment.
General
Construction
Heavy-duty steel
Air Filter
One replaceable air filter at the front
door
Cooling Fan
One 12cm (86.5cfm) ball-bearing fan
Disk Drive Housing
External: 5.25"x1
Internal: 3.5"x1
Indicator
LED indicators for HDD and power
On/Off
Switch
Magic design for wall-mount, desk-top
and rack-mount application
◆
Rugged steel node chassis suitable for
harsh environment
◆
One built-in 12cm ball-bearing fan for
better ventilation
◆
Built-in micro-ATX type power supply
◆
Support one external 5.25" and one
internal 3.5" disk drive
◆
Optional kits to combine two PNC-6162
for the rack-mount application
With an optional built-in EZDRV, PNC-6162 can support a
notebook type CD-ROM and FDD within a 5.25" drive
bay. It helps you to install the system and application
software more easily.
Combining two PNC-6162 into a rack-mount kit with
additional software, you can have a high-availability fault
tolerant system.
Speaker
Input Voltage
One 8Ω speaker
AC 95 - 130V, 190 - 254V selectable
Standard Color
Input Frequency
Beige, Black
47Hz - 63Hz
Dimension
Input Current
PNC-6162:
220(W) x 407(D) x 160(H) mm
8.66"(W) x 16"(D) x 6.3"(H)
7A max./115V, 4A max./230V
Efficiency
Min. 70%
PRC-4164:
482(W) x 407(D) x 177(H) mm
19"(W) x 16"(D) x 7"(H)
MTBF Reliability
Weight
Safety
PNC-6162:
Net: 6.5kg (34.4lb)
Gross: 8.0kg (38.9lb)
Environment
Min. 50,000 hours at 25˚C (70˚F)
UL/CSA/TUV/CE
Operating Temperature Range
One for reset and one for power On/Off
with a protection cap
PRC-4164:
Net: 15.5kg (14.3lb)
Gross: 17.5kg (17.6lb)
0 to +55˚C
Mounting Bracket
Backplane
0 to +70˚C
Two brackets for vertical and horizontal
mounting
Keyboard Connector
Standard 6-pin PS/2 K/B connectors
with a cap
Keyboard Connector Cap
One cap for better security
23
◆
6-slot PICMG PISA bus Backplane
Power Supply
Output Voltage & Current
+5V@12A, +12V@5A,
+3.3V@7A, [email protected]
Storage Temperature Range
Relative Humidity
5 to 95% non-condensing
PRC-4164/PNC-6162
Magic 6-slot Node Chassis
Features
◆
5.25" drive space for EZDRV
◆
◆
Benefits
◆
Built in with FDD and CD-ROM to install software
Replaceable air filter
◆
For easy cleaning
Can be vertically or horizontally mounted
◆
Easy to fit into different space limited environment
◆
Both 6-slot ISA and PICMG BP are applicable
◆
Easy to change to different Backplanes and keep stock
◆
Adopt 150W micro-ATX PSU
◆
Save the space inside the chassis
◆
Special kit to combine dual systems into 4U space
◆
Can be formed as a fault tolerant system
What's New
Special design for the drive bay
Can be mounted in different styles
Easy-to-use control panel
Adopt notebook type device to save space.
PNC-6162's front door can be changed for
either vertical or horizontal installation.
All the switches and LEDs are located at
the front panel for direct operation.
Ordering Guide
Engineering Drawing
PNC-6162-06I-15X
6-slot full-size industrial node chassis
with 6-slot ISA Backplane and 150W
micro-ATX power supply
PNC-6162-06P3-15X
6-slot full-size industrial node chassis
with 6-slot PICMG(3 PCI) Backplane
and 150W MICRO ATX power supply
PRC-4164-06P3-15X
Two sets of PNC-6162 with rack-mount
kit, 6-slot PICMG(3 PCI) Backplane and
150W MICRO ATX power supply
▲ PNC-6162
24
RDA-209
19" 4U 9-drive Rack-mount Disk Array Chassis
◆
The most compact size to fit 9 disk
drives in a 19" rack-mount chassis
◆
Three horizontal drive bays for some
special devices, such as RAID
controller and CD-ROM
◆
450W redundant and standard PS/2
power supply optional
◆
Two cooling fans for better ventilation
◆
Only 4U in height, suitable for
communication node or rack server
◆
Easy for system installation and
maintenance
Specifications
General
Construction
Heavy-duty steel
Cooling
Disk Drive Housing
Standard Color
Dimension
Two 12cm internal cooling fans
Nine 5.25" drive bays
Weight
▲ RDA-209 with redundant PSU
Light gray, black
482(W) x 450(D) x 177(H) mm
19"(W) x 17.7"(D) x 7"(H)
Net: 15kg (33.3lb)
Gross: 16kg (35.6lb)
Power Supply
Maximum Output
450W
Output Voltage
&
Current
Input Voltage
Input Frequency
Input Current
Efficiency
MTBF Reliability
Safety
+5V@30A, +12V@14A,
[email protected], [email protected]
+12V (max. 220W)
90 - 132V/180 - 264V
47Hz - 63Hz
10A@115V, 5A@230V
Min. 80%
Min. 50,000 hours at 25˚C (70˚F)
UL/CUL/TUV/CE
Environment
▲ Power supply bracket
Operating Temperature
Storage Temperature
0 to +55˚C
Relative Humidity
5 to 95% non-condensing
0 to +70˚C
Ordering Guide
RDA-209
19" rack-mount disk array chassis w/o power supply
RDA-209-3002
19" rack-mount disk array chassis with 300W redundant power supply
▲ RDA-209 with PS/2 PSU
RDA-209-38A
19" rack-mount disk array chassis with 380W PS/2 power supply
40
RPC-800
19" 4U Industrial Rack-mount PC Chassis for 14 Full-length Cards
◆
19" rack-mount chassis meets EIA RS310C industrial standard
◆
Rugged construction and design for
harsh industrial environment
◆
Power On/Off switch with LED indicator
and a reset switch inside the lockable
door
◆
Replaceable air filter for easy cleaning
◆
Two cooling fans generate positive air
for better ventilation
◆
Easily-installed drive bracket with shockresistant cushion and well-conductive
rubber
General
◆
Specially designed for 14 full-length cards
Construction
Heavy-duty steel
Air Filter
Cooling
One removable front-panel filter
◆
◆
Support 14-slot ISA and various PICMG
Backplane
Many options of PSU: Safety-approved
380W Auto-range PS/2 PSU, 48VDC/DC
converter and PS/2 type redundant PSU
Ordering Guide
RPC-800-14I-33A
RPC-800 with 14-slot ISA Backplane and
330W PSU
RPC-800-14P4-33A
RPC-800 with 14-slot PICMG Backplane
(4xPCI) and 330W PSU
RPC-800-14AC-33A
RPC-800 with 14-slot PICMG Backplane
(12xPCI) and 330W PSU
RPC-800-14A7-33A
RPC-800 with 14-slot PICMG Backplane
(7xPCI) and 330W PSU
RPC-800-13D4-33A
RPC-800 with dual-system PICMG
Backplane and 330W PSU
Specifications
Disk Drive Housing
Indicator
Switch
Keyboard Connector
Standard Color
Dimension
Weight
Two cooling fans behind the fan filter panel and
one within the PSU
Two 3.5" drive bays
LED indicators for HDD and power On/Off
Reset & power On/Off
PS/2-connectors at both front and rear panel
Light gray
482(W) x 450.8(D) x 177(H) mm
19"(W) x 17.7"(D) x 7"(H)
Net: 15.5kg (34.4lb)
Gross: 17kg (37.8lb)
Backplane
14-slot ISA Backplane
14-slot PICMG (12xPCI) active Backplane
14-slot PICMG (7xPCI) active Backplane
14-slot PICMG (4xPCI) Backplane
13-slot PICMG dual-system Backplane
Power Supply (ORION-330A)
Maximum Output
330W
Output Voltage &
Current
Input Voltage
Input Frequency
Input Current
Efficiency
MTBF Reliability
Safety
+5V@30A, +12V@14A,
[email protected], -12V@1A
95 - 132V/185 - 264V Auto-range
47Hz - 63Hz
10A@115V, 5A@230V
Min. 70%
Min. 50,000 hours at 25˚C (70˚F)
UL/CSA/TUV/FCC/CE
Environment
▲ Top view of RPC-800
39
Operating Temperature
Storage Temperature
0 to +55˚C
0 to +70˚C
Relative Humidity
5 to 95% non-condensing
RPC-600FT
19" 4U Rack-mount Fault Tolerant Server (FTS) Chassis
◆
19" rack-mount chassis meets EIA RS310C industrial standard
◆
Rugged construction suitable for harsh
industrial environment
◆
Power On/Off switch with light indicator
and a reset switch
◆
Nine 5.25" drive bays for various RAID
configuration
◆
Three 12cm ball-bearing cooling fans
generate positive air to have better
ventilation
◆
One keyboard DIN connector on the rear
panel
◆
Specially designed dual-system PICMG
backplane for installing two systems
inside
◆
Support 14-slot PICMG Backplane or
ATX motherboard
◆
Both PS/2 and PS/2 type hot-swap
redundant PSU available
Ordering Guide
Specifications
General
Construction
Heavy-duty steel
Cooling
Three ball-bearing fans between RAID devices and
the system and one within the power
Nine 5.25" drive bays, one for CD-ROM drive or RAID
controller and five for RAID disks
Reset & power On/Off
Disk DriveHousing
Switch
Indicator
Standard Color
Dimension
Weight
Eight LED indicators for HDD and power On/Off switch
Light gray, black
482(W) x 638(D) x 177(H) mm
19"(W) x 25.1"(D) x 7"(H)
Net: 23Kg.(51.1Lb)
Gross: 25Kg.(55.6Lb)
RPC-600FT-14P4-270RD
19" 4U rack-mount FTS chassis with 14-slot
PICMG Backplane and 500W PS/2 type
redundant PSU
RPC-600FT-13D4-270RD
19" 4U rack-mount FTS chassis with dualsystem Backplane and 500W PS/2 type
redundant PSU
RPC-600FT-ATX-270RDX
19" 4U rack-mount FTS chassis with 500W
PS/2 type redundant ATX PSU for ATX M/B
Backplane
13-slot dual-system BP
14-slot PICMG BP
ATX M/B installable
Dual active systems installation:
- System 1 with 2xISA / 4xPCI
- System 2 with 2xISA / 3xPCI
Gold-plated, 4-layer Backplane
Power Supply (BPS-270RD)
Maximum Output
500W
Output Voltage &
Current
Input Voltage
Input Frequency
Input Current
Efficiency
MTBF Reliability
Safety
+5V@30A, +12V@14A, 3.3V@20A (max. 240W),
[email protected], [email protected], [email protected]
90 - 132V/180 - 264V Auto-range
47Hz - 63Hz
6A@115V, 3A@230V
Min. 75%
Min. 50,000 hours at 25˚C (70˚F)
UL/CUL/TUV/CE
Environment
Operating Temperature
Storage Temperature
0 to +55˚C
Relative Humidity
5 to 95% non-condensing
0 to +70˚C
▲ Top view of RPC-600FT
38
RPC-520
19" 20-slot 4U Industrial Rack-mount PC Chassis
◆
19" rack-mount chassis meets EIA RS-310C
industrial standard
◆
Rugged construction suitable for harsh
industrial environment
◆
Lockable front door for dust-proof and
running security
◆
Power On/Off switch with LED indicator
and a reset switch inside the lockable door
◆
Replaceable air filter for easy cleaning
◆
Three cooling fans and easily installed
drive bracket with shock-resistant cushion
and well-conductive rubber
◆
Removable disk drive bracket for 5 devices
(3.5"x3, 5.25"x2)
◆
Support 20-slot ISA, 19-slot PICMG &
multiple-system backplanes
◆
Safety-approved 450W ATX PSU installed
Specifications
General
Construction
Heavy-duty steel
Air Filter
Cooling
One removable front-panel filter
19" 4U industrial chassis with 19-slot ISA
Backplane and 450W PSU
Disk Drive Housing
Indicator
Switch
Keyboard Connector
Standard Color
Dimension
RPC-520-20Q3-450AX
Weight
Ordering Guide
RPC-520-20I-450AX
19" 4U industrial chassis with 20-slot
4-system PICMG BP and 450W PSU
RPC-520-19AI-450AX
19" 4U industrial chassis with 19-slot
PICMG BP (18xPCI) and 450W PSU
RPC-520-19AC-450AX
19" 4U industrial chassis with 19-slot
PICMG BP (12xPCI) and 450W PSU
RPC-520-19P4-450AX
19" 4U industrial chassis with 20-slot ISA
BP and 450W PSU
RPC-520-18D4-450AX
19" 4U industrial chassis with 18-slot
dual-system PICMG BP and 450W PSU
Three cooling fans behind the fan filter panel and
one within the PSU
Five drive bays, 3.5"x3, 5.25"x2
LED indicators for HDD and power On/Off
K/B lock, reset & power On/Off
AT-connectors at both front and rear panel
Light gray
482(W) x 638(D) x 177(H) mm
19"(W) x 25.1"(D) x 7"(H)
Net: 23kg (51.1lb)
Gross: 25kg (55.6lb)
Backplane
20-slot ISA Backplane
20-slot PICMG 4-System Backplane
19-slot PICMG 18xPCI active Backplane
19-slot PICMG 12xPCI active Backplane
19-slot PICMG 4xPCI Backplane
18-slot PICMG dual-system Backplane
Power Supply (ORION-450AX)
Maximum Output
450W
Output Voltage
&
Current
Input Voltage
Input Frequency
Input Current
Efficiency
MTBF Reliability
Safety
+5V@40A, +12V@17A,
+3.3V@28A, [email protected]
[email protected], +5V&+3.3V (max. 225W)
95 - 132V/185 - 264V Auto-range
47Hz - 63Hz
7A@115V, 4A@230V
Min. 70%
Min. 50,000 hours at 25˚C (70˚F)
UL/CSA/TUV/FCC/CE
Environment
▲ Top view of RPC-520
Operating Temperature
Storage Temperature
0 to +55˚C
Relative Humidity
5 to 95% non-condensing
0 to +70˚C
36
RPC-520FT
19" 4U Rack-mount Fault Tolerant Server (FTS) Chassis
◆
19" rack-mount chassis meets EIA RS310C industrial standard
◆
Rugged construction and design for
harsh industrial environment
◆
Front swappable PS/2 type redundant PSU
◆
Design for replaceable RAID disk
◆
Six 5.25" drive bays for various RAID
configuration
◆
Three 12cm ball-bearing cooling fans
generate positive air to have better
ventilation
◆
Special design, multiple (4 or 2) systems
installable
General
Construction
Heavy-duty steel
◆
Safety-approved PS/2 type hot swap
redundant PSU installed
Cooling
Three ball-bearing fans between RAID devices and
the system and one within the power
Six 5.25" drive bays, one for CD-ROM drive or RAID
controller and five for RAID disks
Four reset & power On/Off
Beige, black
Specifications
Disk Drive Housing
Ordering Guide
RPC-520FT-20Q3-270RD1
19" 4U rack-mount FTS chassis with 20-slot
4-system PICMG Backplane and 500W
redundant PSU
RPC-520FT-19P4-270RD1
19" 4U rack-mount FTS chassis with 19-slot
PICMG Backplane and 450W redundant
PSU
RPC-520FT-18D4-270RD1
19" 4U rack-mount FTS chassis with dualsystem Backplane and 500W PS/2 type
redundant PSU
Switch
Standard Color
Dimension
Weight
482(W) x 638(D) x 177(H) mm
19"(W) x 25.1"(D) x 7"(H)
Net: 23kg (51.1lb)
Gross: 25kg (55.6lb)
Backplane
20-slot PICMG 4-system Backplane
19-slot PICMG 18xPCI active Backplane
19-slot PICMG 12xPCI active Backplane
19-slot PICMG 4xPCI Backplane
18-slot PICMG dual-system Backplane
ATX M/B installable
Power Supply (BPS-270RD-1)
Maximum Output
500W
Output Voltage &
Current
Input Voltage
Input Frequency
Input Current
Efficiency
MTBF Reliability
Safety
+5V@30A, +12V@14A (max. 240W),
[email protected], [email protected]
90 - 132V/180 - 264V Auto-range
47Hz - 63Hz
6A@115V, 3A@230V
Min. 75%
Min. 50,000 hours at 25˚C (70˚F)
UL/CUL/TUV/CE
Environment
▲ Top view of RPC-520FT
37
Operating Temperature
Storage Temperature
0 to +55˚C
0 to +70˚C
Relative Humidity
5 to 95% non-condensing
RPC-500NP
Industrial Chassis
The Most Cost-effective 19" 4U Rack-mount PC Chassis
RPC-500NP is the most cost-effective 19" 4U rack-mount
chassis designed for various kinds of servers, Computer
Telephony Integration (CTI) and telecommunication
applications.
The rugged, sturdy, full-sealed and well-cooled steel
chassis is specially designed to withstand heavy shocks,
dust, humidity, trembling vibration and extremely high
operating temperature in the harsh environment.
u
Three 5.25" and two 3.5" drive bays for
RAID 0, 1, 5 & CD-ROM
u
Two ball-bearing cooling fans for better
ventilation
u
Traditional rack-mount handles
u
Dual card retainer positions and one K/B
connector cap included
u
One modularized function panel for
single & dual systems
u
ATX M/B applicable, especially for bigAT size M/B
u
PS/2 redundant power supply installable
These useful enhancements to meet the newest
technology make RPC-500NP the best choice to integrate
your rack-mount systems.
We enhanced RPC-500NP with a special designed
driver- set to hold one more device such as CD-ROM with
FDD inside the chassis, it will leave more device space
for high level application.
General
Dimension
Input Current
Construction
482(W) x 450(D) x 177(H) mm
19"(W) x 17.7"(D) x 7"(H)
10A max./115V, 5A max./230V
Weight
Min. 70%
Net: 15.5kg (34.4lb)
Gross: 17.5kg (38.9lb)
MTBF Reliability
Heavy-duty steel with aluminum front
panel
Air Filter
One replaceable filter
Cooling Fan
One 12cm (86.5cfm) and one 8cm
(35.3cfm) ball-bearing cooling fans
Disk Drive Housing
3x5.25"+2x 3.5" (one for external FDD
and one for internal HDD) drive bays
Card Retainer
Backplane
14-slot ISA backplane
14-slot PICMG 12xPCI active Backplane
14-slot ctive Backplane
14-slot PICMG 4xPCI Backplane
13-slot PICMG dual-system Backplane
Maximum Output
Switch
330W
One for reset, one for power On/Off and
one for K/B lock
Output Voltage & Current
+5V@30A, +12V@14A,
[email protected], -12V@1A
Standard PS/2 K/B connector at the
front panel
Input Voltage
Keyboard Connector Cap
Input Frequency
One cap at the front panel
Standard Color
Beige, black
Min. 50,000 hours at 25˚C (70˚F)
Safety
UL/CSA/TUV/FCC/CE
Environment
Operating Temperature Range
0 to +55˚C
Power Supply (ORION-330A)
Two locations for one card retainer
Keyboard Connector
Efficiency
95 - 132V/185 - 264V Auto-range
47Hz - 63Hz
Storage Temperature Range
0 to +70˚C
Relative Humidity
5 to 95% non-condensing
F CD-ROM & mobile rack are
optional items , not included in
standard models .
The Most Cost-effective 19" 4U Rack-mount PC Chassis
Features
Benefits
19" 4U Rack-mount chassis meets EIA RS-310C standard
u
Easy to fit in a 19" cabinet from different venders
u
A lockable front door with acrylic windows
Power switch with LED indicator, reset and K/B lock
switches inside the lockable door
u
Good for dust-proof
Avoid accidental reset for better running security
Running status visible
u
u
Modularized function panel for one or dual systems
Reserve LED holes for redundant PSU
u
Easy for installing dual systems and redundant PSU
Easy to keep stock and OEM project
u
Replaceable air filter
u
Good for easy cleaning
u
New K/B connector cap
u
Good for dust-proof at the front K/B connector
u
Two ball-bearing cooling fans
u
Better ventilation to provide the system with higher reliability
u
Enhanced drive bracket to hold 3x5.25"+1x3.5" (or EZ-Kit)
and 1x3.5" drives (internal)
u
u
More flexibility to integrate varied systems
Suitable for installing RAID and CD-ROM drive
u
Shock-mount cushion for the drive bracket
u
Suitable for harsh industrial environment
u
Changeable modularized back panel for 14-slot ISA/PICMG BP Only one minute needed to change the back panel
u Easy to change to different Backplanes and keep stock
or ATX M/B
u
Field replaceable power supply bracket for both normal
PS/2 PSU and PS/2 type redundant PSU
u
u
u
u
u
u
u
u
Only 3 minutes needed to change the defective PSU
Only 30 seconds to change the defective PSU module
Engineering Drawing
Industrial Chassis
RPC-500NP
RPC-500N/L
The Most Cost-effective 19" 4U Rack-mount PC Chassis
RPC-500N is the most cost-effective 19" 4U rack-mount
chassis designed for various kinds of servers, Computer
Telephony Integration (CTI) and telecommunication
applications.
The rugged, sturdy, full-sealed and well-cooled steel
chassis is specially designed to withstand heavy shocks,
dust, humidity, trembling vibration and extremely high
operating temperature in the harsh environment.
Three 5.25" and two 3.5" drive bays for
RAID 0, 1, 5 & CD-ROM
◆
Dual ball-bearing cooling fans for better
ventilation
◆
Traditional rack-mount handles
◆
Dual card retainer positions and one K/B
connector cap included
◆
One modularized function panel for
single & dual systems
◆
ATX M/B applicable, especially for bigAT size M/B
◆
PS/2 redundant power supply installable
RPC-500L is extended to 51.5 cm (20.2") for the newest
ATX server M/B, especially for dual Pentium® II (440BX)
processor based M/B. With such a compact size, RPC500L can be installed into a 60cm (23.6") rack-mount
cabinet. These useful enhancements to meet the newest
technology make RPC-500N/500L the best choice to
integrate your rack-mount systems.
General
Dimension
Output Voltage & Current
Construction
RPC-500N:
482(W) x 450(D) x 177(H) mm
19"(W) x 17.7"(D) x 7"(H))
+5V@30A, +12V@14A,
[email protected], -12V@1A
RPC-500L:
482(W) x 515(D) x 177(H) mm
19"(W) x 20.3"(D) x 10.5"(H)
95 - 132V/185 - 264V auto-range
Heavy-duty steel with aluminum front
panel
Air Filter
One replaceable filter
Cooling Fan
One 12cm (86.5cfm) one 8cm (35.3cfm)
ball bearing cooling fan
Disk Drive Housing
3x5.25"+2x 3.5" (one for external FDD
and one for internal HDD) drive bays
Card Retainer
Two locations for one card retainer
Switch
One for reset, one for power On/Off and
one for K/B lock
Keyboard Connector
Standard 6-pin AT K/B connectors at the
front and the rear panel
Keyboard Connector Cap
One cap at the front panel
Standard Color
Beige, black
37
◆
Weight
RPC-500N:
Net: 15.5Kg.(34.4 lb)
Gross: 17.5Kg.(38.9 lb)
RPC-500L:
Net: 15.5Kg.(34.4 lb)
Gross: 17.5Kg.(38.9 lb)
Backplane
14-Slot ISA backplane
14-Slot PICMG 12xPCI active backplane
14-Slot PICMG 7xPCI active backplane
14-Slot PICMG 4xPCI backplane
13-Slot PICMG dual-system backplane
Power Supply (ORION-330A)
Maximum Output
330W
Input Voltage
Input Frequency
47Hz - 63Hz
Input Current
10A max./115V, 5A max./230V
Efficiency
Min. 70%
MTBF Reliability
Min. 50,000 hours at 25˚C (70˚F)
Safety
UL/CSA/TUV/FCC/CE
Environment
Operating Temperature Range
0 to +55˚C
Storage Temperature Range
0 to +70˚C
Relative Humidity
5 to 95% non-condensing
RPC-500N/L
The Most Cost-effective 19" 4U Rack-mount PC Chassis
Features
◆
Benefits
19" 4U rack-mount chassis meets EIA RS-310C standard
A Lockable front door with acrylic windows
◆ Power ON/OFF switch with LED indicator, reset and K/B lock
switches inside the lockable door
◆
◆
Easy to fit in a 19" cabinet from different venders
Good for dust-proof
Avoid accidental reset for better running security
◆ Running status is visible
◆
◆
◆
Modularized function panel for one or dual systems
Reserve LED holes for redundant PSU
◆
Replaceable air filter
◆
Good for easy cleaning
◆
Two K/B DIN connectors on both front and rear panels
◆
Convenient to connect to the keyboard
◆
New K/B connector cap
◆
Good for dust-proof at the front K/B connector
◆
Dual ball-bearing cooling fan
◆
Better ventilation to provide the system with higher reliability
◆
Enhanced drive bracket to hold 3x5.25"+1x3.5" (external) and
1x3.5" drives (internal)
◆
More flexibility to integrate varied systems
Suitable for installing RAID and CD-ROM drive
◆
◆
◆
◆
Easy for installing dual systems and redundant PSU
Easy to keep stock and OEM project
◆
Shock-mount cushion for the drive bracket
◆
Suitable for harsh industrial environment
◆
Two adjustable positions for hold-down card retainers
◆
More flexibly and tightly to fix all the cards
◆
Changeable modularized back panel for 14-slot ISA/PICMG BP Only one minute needed to change the back panel
◆ Easy to change to different backplanes and keep stock
or ATX M/B
◆
Field replaceable power supply bracket for both normal
PS/2 PSU and PS/2 type redundant PSU
◆
◆
◆
Only 3 minutes needed to change the defective PSU
Only 30 seconds to change the defective PSU module
What's New
Redundant power supply
3x5.25"+2x3.5" drive space
ATX motherboard
Our new PSU bracket can install either
PS/2 type PSU or PS/2 redundant PSU to
enhance its security for high-end systems.
IRC-500N enhances the drive bracket to
hold up to 3x5.25"+2x3.5" disk drives for
floppy, hard disk and CD-ROM.
ATX mother board can be installed inside
IRC-500N just by changing the
modularized back panel.
Replaceable function panel
Replaceable panel for PSU modules
Dual fans for better ventilation
Two modular designed function panels are
IRC-500N is designed to install different
IRC-500N is equipped with two ball
available for single or dual system display
panels. Any OEM project is welcome.
power supply panels for PS/2 or
redundant PS/2 type PSU.
bearing fans to have better ventilation and
a replaceable filter to exclude dust.
Dual card retainers position
New rack-mount handle
K/B connector cap
Two positions for card clamps to hold both
PCI and ISA cards more tightly.
The new handles are designed to hold the
system tightly and distinguish from others.
IRC-500N includes a keyboard connector
cap to prevent dust.
38
RPC-500N/L
The Most Cost-effective 19" 4U Rack-mount PC Chassis
Engineering Drawing
Ordering Guide
PICMG Version
RPC-500N-14I-33A
19" 4U rack-mount chassis with 14-slot ISA backplane and
330W auto-range AT PSU
RPC-500N-14P4-33A
19" 4U rack-mount chassis with 14-slot PICMG BP and 330W
auto-range AT PSU
Except the rack-mount handle, IRC-500N is the
same as RPC-500N as the best selling 4U rackmount chassis for CTI, industrial, scientific,
engineering and server applications.
RPC-500N-14A7-33A
19" 4U rack-mount chassis with 14-slot 7-PCI PICMG
BACKPLANE and 330W auto-range AT PSU
M/B Version
RPC-500N-M-25
19" 4U rack-mount chassis for baby-AT M/B with 250W AT PSU
RPC-500N-MX-30X
19" 4U rack-mount chassis for ATX M/B with 300W ATX PSU
(Chassis can be changed to RPC-500N or RPC-500L)
39
▲ IRC-500N
RPC-500NE
The Most Cost-effective 19" 4U Rack-mount PC Chassis
RPC-500NE is the most cost-effective 19" 4U rack-mount
chassis designed for various kinds of servers, Computer
Telephony Integration (CTI) and telecommunication
applications.
The rugged, sturdy, full-sealed and well-cooled steel
chassis is specially designed to withstand heavy shocks,
dust, humidity, trembling vibration and extremely high
operating temperature in the harsh environment.
Three 5.25" and two 3.5" drive bays for
RAID 0, 1, 5 & CD-ROM
◆
Two ball-bearing cooling fans for better
ventilation
◆
Traditional rack-mount handles
◆
Dual card retainer positions and one K/B
connector cap included
◆
One modularized function panel for
single & dual systems
◆
ATX M/B applicable, especially for bigAT size M/B
◆
PS/2 redundant power supply installable
These useful enhancements to meet the newest
technology make RPC-500NE the best choice to integrate
your rack-mount systems.
We enhanced RPC-500NE with a special designed
drivers set to hold one more device such as CD-ROM
with FDD inside the chassis, it will leave more device
space for high level application.
General
Dimension
Input Current
Construction
482(W) x 450(D) x 177(H) mm
19"(W) x 17.7"(D) x 7"(H)
10A max./115V, 5A max./230V
Heavy-duty steel with aluminum front
panel
Weight
Min. 70%
Air Filter
Net: 15.5kg (34.4lb)
Gross: 17.5kg (38.9lb)
MTBF Reliability
One replaceable filter
Cooling Fan
One 12cm (86.5cfm) and one 8cm
(35.3cfm) ball-bearing cooling fans
Disk Drive Housing
3x5.25"+2x 3.5" (one for external FDD
and one for internal HDD) drive bays
Card Retainer
Backplane
14-slot ISA backplane
14-slot PICMG 12xPCI active Backplane
14-slot PICMG 7xPCI active Backplane
14-slot PICMG 4xPCI Backplane
13-slot PICMG dual-system Backplane
Power Supply (ORION-330A)
Maximum Output
Switch
330W
One for reset, one for power On/Off and
one for K/B lock
Output Voltage & Current
+5V@30A, +12V@14A,
[email protected], -12V@1A
Standard 6-pin PS/2 K/B connectors at
the front and the rear panel
95 - 132V/185 - 264V Auto-range
Keyboard Connector Cap
Input Frequency
One cap at the front panel
Standard Color
Beige, black
Efficiency
Min. 50,000 hours at 25˚C (70˚F)
Safety
UL/CSA/TUV/FCC/CE
Environment
Operating Temperature Range
0 to +55˚C
Two locations for one card retainer
Keyboard Connector
33
◆
Input Voltage
47Hz - 63Hz
Storage Temperature Range
0 to +70˚C
Relative Humidity
5 to 95% non-condensing
RPC-500NE
The Most Cost-effective 19" 4U Rack-mount PC Chassis
Features
◆
Benefits
19" 4U Rack-mount chassis meets EIA RS-310C standard
A lockable front door with acrylic windows
◆ Power ON/OFF switch with LED indicator, reset and K/B lock
switches inside the lockable door
◆
◆
◆
Modularized function panel for one or dual systems
Reserve LED holes for redundant PSU
◆
Easy to fit in a 19" cabinet from different venders
Good for dust-proof
◆ Avoid accidental reset for better running security
◆ Running status visible
◆
◆
◆
Easy for installing dual systems and redundant PSU
Easy to keep stock and OEM project
◆
Replaceable air filter
◆
◆
Two K/B DIN connectors on both front and rear panels
◆
Convenient to connect to the keyboard
◆
New K/B connector cap
◆
Good for dust-proof at the front K/B connector
◆
Two ball-bearing cooling fans
◆
Better ventilation to provide the system with higher reliability
◆
Enhanced drive bracket to hold 3x5.25"+1x3.5" (or EZ-Kit)
and 1x3.5" drives (internal)
◆
◆
More flexibility to integrate varied systems
Suitable for installing RAID and CD-ROM drive
◆
Shock-mount cushion for the drive bracket
◆
Suitable for harsh industrial environment
◆
Two adjustable positions for hold-down card retainers
◆
More flexibly and tightly to fix all the cards
◆
Changeable modularized back panel for 14-slot ISA/PICMG BP ◆ Only one minute needed to change the back panel
◆ Easy to change to different Backplanes and keep stock
or ATX M/B
◆
Field replaceable power supply bracket for both normal
PS/2 PSU and PS/2 type redundant PSU
◆
◆
Good for easy cleaning
Only 3 minutes needed to change the defective PSU
Only 30 seconds to change the defective PSU module
What's New
Special designed drivers set
3x5.25"+2x3.5" drive space
ATX motherboard
Special designed drivers set to hold one
slim CD-ROM & FDD, it can leave more
drive space available for higher application.
RPC-500NE enhances the drive bracket
to hold up to three 5.25" and two 3.5"
drive bays for RAID 0, 1, 5 & CD-ROM.
ATX mother board can be installed inside
RPC-500NE just by changing the
modularized back panel.
Replaceable function panel
Replaceable panel for PSU modules
Two fans for better ventilation
Two modular designed function panels are
available for single or dual system display
panels. Any OEM project is welcome.
RPC-500NE is designed to install different
PSU panels for PS/2 or redundant PS/2
type power supply.
RPC-500NE is equipped with two ballbearing fans to have better ventilation and
a replaceable filter to exclude dust.
Dual card retainers position
K/B connector cap
Two positions for card clamps to hold both
PCI and ISA cards more tightly.
RPC-500NE includes a PS/2 keyboard
connector cap to prevent dust.
34
RPC-500NE
The Most Cost-effective 19" 4U Rack-mount PC Chassis
Engineering Drawing
Ordering Guide
PICMG Version
RPC-500NE-14I-330A
19" 4U rack-mount chassis with 14-slot ISA Backplane and
330W Auto-range AT PSU
RPC-500NE-14P4-330A
19" 4U rack-mount chassis with 14-slot PICMG BP and 330W
Auto-range AT PSU
RPC-500NE-14A7-330A
19" 4U rack-mount chassis with 14-slot 7-PCI PICMG
Backplane and 330W Auto-range AT PSU
M/B Version
RPC-500NE-MX-30X
19" 4U rack-mount chassis for ATX M/B with 300W ATX PSU
EZ-Kit (optional)
The Kit to hold one slim type CD-ROM & FDD in a enhanced
3.5" drive bay
35
IRC-305
Advanced 19" 2U Industrial Rack-mount PC Chassis
IRC-305 is a compact and rugged 19" 2U rack-mount
chassis designed for space limited application, especially
in the telecommunication environment. Its rugged, sturdy,
full-sealed and well-cooled steel chassis is specially
designed to withstand shocks, dust, humidity, trembling
vibration and high operating temperature in the harsh
environment .
General
Construction
19" 2U rack-mount chassis meets EIA
RS-310C industrial standard
◆
5.25"x1+3.5" FDDx1+3.5" HDDx1 drive bay
◆
Replaceable air filter for easy cleaning
◆
Two 8cm ball-bearing cooling fans for
better ventilation
◆
One On/Off switch protection cap and one
touch free reset for secure access
◆
One K/B connector cap to prevent the front
K/B connector from the dust
◆
Replaceable back panel, easy to change to
different Backplanes
◆
PS/2 redundant power supply installable
◆
Field replaceable PS/2 PSU applicable,
easy for maintenance
The space inside a cabinet is more valuable than before
as the Internet business blooming. A 2U chassis, which
needs just a compact system for the application, saves
half the space than the traditional 4U chassis.
With the power switch protection cap, IRC-305 can avoid
accidental reset of the system.
Speaker
Input Frequency
One 8Ω speaker
43Hz - 63Hz
Heavy-duty steel with aluminum front
panel
Standard Color
Input Current
Beige, black
8A max./115V, 4A max./230V
Air Filter
Dimension
Efficiency
One replaceable air filter
482(W) x 430.6(D) x 88(H) mm
19"(W) x 17"(D) x 3.5"(H)
Min. 70%
Two 8cm (35.3cfm) ball- bearing fans
Weight
Min. 50,000 hours at 25˚C (70˚F)
Disk Drive Housing
Net: 10.5kg (23.1lb)
Gross: 11.5kg (25.3lb)
Safety
Cooling Fan
MTBF Reliability
UL/CSA/TUV/FCC/CE/CB
5.25"x1+3.5"x2 (one external FDD, one
external HDD)
Backplane
Indicator
Vertical 6-slot ISA Backplane
Vertical 6-slot PICMG 4xPCI Backplane
Environment
Power Supply (PW-250)
0 to +55˚C
LED indicators for HDD and power
On/Off
Switch
One for reset and one for power On/Off
with a protection cap
Keyboard Connector
Standard PS/2 K/B connector at the
front panel
Keyboard Connector Cap
One cap at the front panel
25
◆
Maximum Output
250W
Output Voltage & Current
+5V@25A, +12V@10A,
[email protected], [email protected]
Input Voltage
95 - 130V/190 - 254V selectable
Operating Temperature Range
Storage Temperature Range
0 to +70˚C
Relative Humidity
5 to 95% non-condensing
IRC-305
Advanced 19" 2U Industrial Rack-mount PC Chassis
Features
Benefits
◆
Meet EIA RS-310C standard
◆
Easy to fit in different 19" rack-mount cabinet
◆
Replaceable air filter
◆
For easy cleaning
◆
ON/OFF switch protection cap & touch-free reset
◆
Avoid accidental reset of system
◆
K/B connector cap included
◆
For dust-proof for the front K/B connector
◆
Two 8cm ball-bearing cooling fans
◆
Better ventilation to enhance system reliability
◆
Replaceable back panel
◆
Easy to change to different Backplanes
◆
Field replaceable PS/2 PSU
◆
Easy maintenance
What's New
Detachable card cage
Two fans for better ventilation
Touch-free ON/OFF & reset switch
IRC-305 is equipped with a detachable
card cage to install the boards more easily.
Two 8cm ball-bearing fan for better
ventilation.
For security reasons, a switch protection
cap is provided to prevent accidental reset.
Ordering Guide
Engineering Drawing
IRC-305-06V-25
19" 2U rack-mount chassis with
vertical 6-slot ISA Backplane and
250W power supply
IRC-305-06V4-25
19" 2U rack-mount chassis with
vertical 6-slot PICMG (4xPCI)
Backplane and 250W PSU
IRC-305-06V4-30X
19" 2U rack-mount chassis with
vertical 6-slot PICMG (4xPCI)
Backplane and 300W ATX PSU
26
PRC-2193/2193P
Advanced 19" 2U Industrial Rack-mount
PC Chassis
PRC-2193/P has been very well sold and is still one of the most
popular items among Portwell's chassis family. To meet the new
technology on CPU and to re-strength PRC-2193/P's features,
Portwell has improved PRC-2193/P in two ways. One is the solution
for P4, and the other is the mechanical design for more easy
maintenance.
As P4 solution, Portwell concerns not only for her own SBC, but
Main
Main Feature
Feature
P4 sloution ready for both M/B and SBC
Riser card and rear panel optional
19" rack-mount chassis meets EIA RS310C industrial standard
Rugged construction and design for harsh
industrial environment
Power On/Off switch with LED indicator
and a reset switch inside the lockable
door
Two cooling fans generate positive air for
better ventilation
Easily installed drive bracket with shockresistant cushion and well-conductive
rubber
Special design for 4 full-length cards with
detachable card cage
also for customers who need M/B solution. In order to ensure the
speed of dissipating the higher heat from P4 CPU, the airflow has been
rechecked. Also, in order to prevent board's bending by carrying the
heavy P4 CPU heat sink, the chassis base is enforced.
Also, committing customers' strong request on easy maintenance like
IRC-305's detachable card cage design, PRC-2193/P is also
implemented.
General
Construction
Device bays
Cooling Fan
Indicators and SW
Air Filter
Speaker
Standard Color
Dimension
Weight
Backplane
Heavy-duty steel with aluminum front panel
PRC-2193P : 3 drive bays, one for 5.25", two for 3.5"(one internal)
PRC-2193 : 4 drive bays, one for 5.25", three for 3.5" (two internal)
Two 8cm ball-bearing cooling fans
LED indicators for HDD and power On/Off
One for reset and one for power On/Of
f
One replaceable air filter
One 8 speaker
Beige, black
482.6(W) x 495.1(D) x 88.6(H) mm ;19"(W) x 19.5"(D) x 3.5"(H)
Net: 10.5kg (23.1lb) ; Gross: 11.5kg (25.3lb)
Vertical 6-slot (4xPCI) Backplane (for PRC-2193P)
Power Supply
300W (PRC-2193P) ; 150W (PRC-2193)
Output Voltage & Current PRC-2193P : +5V@26A, +12V@11A, +3.3V@6A, [email protected], -12V@1A
PRC-2193 : +5V@30A, +12V@14A, +3.3V@7A, [email protected]
Input Voltage
AC 95 - 130V, 190 - 254V selectable
Input Frequency
47Hz - 63Hz
Input Current
7A max./115V, 4A max./230V
Efficiency
Min. 70%
MTBF Reliability
Min. 50,000 hours at 25˚C (70˚F)
Safety
UL/CSA/TUV/CE
Maximum Output
Environment
Operating Temperature Range 0 to +55˚C
Storage Temperature Range
0 to +70˚C
Relative Humidity
5 to 95% non-condensing
PRC-2193/2193P
Advanced 19" 2U Industrial Rack-mount
PC Chassis
Features
Benefits
Meet EIA RS-310C standard
Replaceable air filter
Easy to fit in different 19" rack-mount cabinet
For easy cleaning
Dual ball-bearing cooling fans
Replaceable back panel
Better ventilation to enhance system reliability
Easy to change to different backplane
Front door equipped with a key
Field replaceable PS/2 power supply
Better security control for the system
Easy for maintenance
What's
What's New
New
Visible Drive Cover
Two fans for better ventilation
Smart PCI Riser Cards for M/B
Switches are inside the drive cover of
PRC-2193 for better security control.
Two 8cm ball-bearing fans are equipped
to keep better ventilation inside.
PRC-2193 is built with 2 PCI riser cards
to have two PCI slots in good reliability.
Space for Dual 3.5" HDD in PRC-2193
Well designed B/P for PRC-2193P
Space for 3.5" HDD in PRC-2193P
PRC-2193 reserves two 3.5" HDD drive
bays behind the fan sets to give higher
system performance.
PRC-2193P can hold a PBP-06V4 to
offer 4 PCI slots to PICMG system with
detachable card cage.
PRC-2193P reserves one 3.5" HDD drive
bays between PSU and CD-ROM.
Ordering Guide
Engineering
Engineering Drawing
Drawing
PRC-2193-MX-30S
Advanced 19" 2U rack-mount chassis for ATX M/B with 2 PCI
slots and 300W Micro ATX PSU
PRC-2193-MX-15X
Advanced 19" 2U rack-mount chassis for ATX M/B with 2 PCI
slots and 150W Micro ATX PSU
PRC-2193P-06V4-30X
Advanced 19" 2U rack-mount chassis with PICMG Backplane,
4 PCI slots and 300W ATX PSU
PRC-2193A
Advanced 19" 2U rack-mount chassis for ATX M/B with 1 AGP
One St
in Com
ead
m
Ah
tions!
ica
un
ep
slot and 1 PCI slot
Portwell, Inc.
Headquarter
3F, No. 92, Nei-Hu Rd., Sec. 1,
114 Taipei, Taiwan, R.O.C.
Tel: +886-2-27992020
Fax: +886-2-27991010
E-mail: [email protected]
http://www.portwell.com.tw
American Portwell
eMCA (UK) Ltd.
Portwell Japan, Inc.
38507 Cherry St. Suite D,
Newark, CA 94560 USA
Tel: +1-510-790-9192
Fax: +1-510-790-9191
E-mail: [email protected]
http://www.portwell.com
Unit 30, Basepoint Enterprise Centre
Stroudley Road, Basingstoke, Hampshire,
RG24 8UP UK
Tel: +44-1256-406688
Fax: +44-1256-406689
E-mail: [email protected]
http://www.emca.co.uk
¢E101-0042 Ueda Build. 7F, 10-2
Kanda higashi matsushita-cho
chiyoda-ku Tokyo Japan
Tel: +81-3-5298-8071
Fax: +81-3-5298-8072
E-mail: [email protected]
http://www.portwell.co.jp
PRC-1234
Compact 19" 1U Industrial Rack-mount Chassis for ATX M/B
1U PCI expansion slot available
For ATX motherboard (recommend Tyan
2420 and Gigabyte GA-6VXDR2)
◆ 2x5.25" HDD, 1 NB CD-ROM & 1 standard
3.5" FDD
◆ Compact and slim design with stylish
protective cover
◆ One blower (97x95x33 mm) and two fans
(40x40x20 mm)
◆ HDD, LAN and power LED indicators
◆ 250W power supply
◆ Dimension: 482.6(W) x 600(D) x 44(H) mm
◆
◆
PRC-1173
Super Slim 19" 1U Industrial Rack-mount PC Chassis
PRC-1173 is a super slim 19" 1U rack-mount chassis
designed for space limited applications, especially in the
Internet colocation applications. Its rugged, sturdy, fullsealed steel chassis and well-concerned ventilation are
designed to withstand shocks, dust, humidity, trembling
vibration and high operating temperature in the harsh
environment.
Designed as a user-concerned product, PRC-1173 is
equipped with an optional PCI or ISA slot for expansion. It
holds one more PCI add-on card than any other legacy
design to offer the best flexibility and meet customers'
demands.
General
19" rack-mount chassis meets EIA RS-310C
industrial standard
◆
The slimmest design for Internet application
◆
Power On/Off switch on the rear side and a
reset switch inside the lockable door
◆
Four cooling fans generate positive air for
better ventilation
◆
Easily-to-install drive bracket with shockresistant cushion design
◆
Special Backplane design for one PCI or
ISA slot
The space inside a cabinet is more valuable than before
as the Internet business is booming lately. As an 1U
chassis, a super slim system for the application, PRC1173 saves much more space than the traditional 4U
chassis.
To overcome the space limitation problem, PRC-1173
integrates CD-ROM, FDD and HDD together inside the
rack. Only of 1U in height, PRC-1173 has all the
necessary functionality as a 2U or 4U system.
Speaker
Input Current
One 8Ω speaker
40A max./115V, 2A max./230V
Heavy-duty steel with aluminum front
panel
Standard Color
Efficiency
Beige, black
Min. 60%
Air Filter
Dimension
MTBF Reliability
One replaceable air filter
482.6(W) x 438(D) x 44(H) mm
19"(W) x 17.2"(D) x 1.7"(H)
Min. 50,000 hours at 25˚C (70˚F)
Construction
Cooling Fan
Safety
Four 4cm ball-bearing cooling fans
Weight
UL/TUV/CUL/CE/FCC
Disk Drive Housing
Net: 8.5kg (18.7lb)
Gross: 9.5kg (20.9lb)
Environment
Special bracket and converting board to
hold notebook type CD-ROM, FDD and
HDD together inside a 5.25" drive bay
Indicator
LED indicators for HDD and power
On/Off
Switch
One for reset and one for power On/Off
with a protection cap
Keyboard Connector
Standard 6-pin PS/2 K/B connectors at
the front panel
Backplane
Support 2-slot (1xPICMG, 1xPCI or ISA)
Power Supply
Output Voltage & Current
+5V@10A, +12V@6A,
[email protected], -12V@1A
Input Voltage
AC 95 - 135V, 180 - 265V AC Autorange
Input Frequency
47Hz - 63Hz
19
◆
Operating Temperature Range
+10 to +50˚C
Storage Temperature Range
-20 to +60˚C
Relative Humidity
5 to 95% non-condensing
PRC-1173
Super Slim 19" 1U Rack-mount PC Chassis
Features
Benefits
◆
Meet EIA RS-310C standard
◆
Easy to fit in different 19" rack-mount cabinet
◆
Replaceable air filter
◆
For easy cleaning
◆
Four 4cm ball-bearing cooling fans
◆
Better ventilation to enhance system reliability
◆
Smart design of 3 in 1 drive kit
◆
FDD, HDD & CD-ROM only take 5.25" drive space
◆
Equipped with a front door
◆
Better security control for the system
◆
One PCI or ISA expansion slot available
◆
New legacy cards adoptable
◆
Customized 150W power supply
◆
Provide sufficient power source to the system
What's New
Smart 3 in 1 drive kit
Well-designed cooling system
Flexible design for slot expansion
A smart design to integrate CD-ROM, FDD
and HDD into a 5.25" drive bay.
With four 4cm cooling fans to expire heat,
PRC-1173 gives higher reliability.
The unique design can hold the PCI or ISA
add-on card without modification needed.
Ordering Guide
Engineering Drawing
PRC-1173-02V1-15A
Super slim 19" 1U rack-mount PC
chassis with 1-slot PCI or 1-slot ISA BP
and 150W Auto-range PSU
PRC-1173-02V1X-15AX
Super slim 19" 1U rack-mount PC
chassis with 1-slot PCI or 1-slot ISA BP
and 150W Auto-range ATX PSU
PRC-1173-02V1X-25S
Super slim 19" 1U rack-mount PC
chassis with 1-slot PCI or 1-slot ISA BP
and 250W Auto-range ATX PSU
▲ PRC-1173 in beige
20
IRC-215N/PIK-215A
19" 1U Rack-mount Keyboard Drawer with Keyboard & Trackball
◆
Smart and compact design for rackmount application
◆
1U (1.75") in height to save space
◆
Equipped with 101-key keyboard and
trackball
Ordering Guide
IRC-215N
19" 1U industrial keyboard drawer with
101-key keyboard & trackball
PIK-215A
19" 1U industrial keyboard drawer with
101-key keyboard & trackball
IRC-215N is the slimmest keyboard drawer which houses a compact
IBM-PC XT/AT compatible 101-key keyboard and a trackball for Windows
application. It has a slide bar for holding the keyboard and trackball cable
for smooth operation.
Engineering Drawing
Specifications
Keyboard
No. of Keys
101
Keys Travel
LED
MTBF
Interface
Safety
4mm
Num. Cap. Scroll Lock
10 million strokes
AT or PS/2
UL, CE
Trackball
No. of Keys
3
Compatibility
Interface
Safety
Microsoft
DB9 or PS/2
UL, CE
General
Construction
Heavy-duty steel
Color
Drawer Travel
Dimension
Beige, black
11"
Weight
Operating Temperature
Storage Temperature
Relative Humidity
▲ PIK-215A
41
482.8(W) x 333(D) x 44(H) mm
19"(W) x 13.1"(D) x 1.7"(H)
Net: 5.5kg (12.2lb)
Gross: 6.5kg (14.4lb)
0 to +55˚C / 20-90%RH
0 to +70˚C / 5-95%RH
5 to 95% non-condensing
IRC-210N/PIK-210A
19" 1U Rack-mount Keyboard Drawer with 101-Key Keyboard
◆
Smart and compact design for rackmount application
◆
1U (1.75") in height to save space
◆
Equipped with 101-key keyboard
Ordering Guide
IRC-210N
19" 1U industrial keyboard drawer with
101-key keyboard
PIK-210A
19" 1U industrial keyboard drawer with
101-key keyboard
IRC-210N, a slim keyboard drawer which houses a specially compact
IBM-PC XT/AT compatible 101-key keyboard, is nearly the same as IRK215 except trackball.
Engineering Drawing
Specifications
Keyboard
No. of Keys
101
Keys Travel
LED
MTBF
Interface
Safety
4mm
Num. Cap. Scroll Lock
>10 million strokes
AT or PS/2
UL, CE
General
Construction
Heavy-duty steel
Color
Drawer Travel
Dimension
Beige, black
11"
Operating Temperature
Storage Temperature
482.8(W) x 333(D) x 44(H) mm
19"(W) x 13.1"(D) x 1.7"(H)
Net: 4.2kg (9.3lb)
Gross: 5.6kg (12.4lb)
0 to +55˚C / 20-90%RH
0 to +70˚C / 5-95%RH
Relative Humidity
5 to 95% non-condensing
Weight
▲ PIK-210A
42
PNC-5063
Advanced 6-slot Industrial Node Chassis for half-size PCI cards
◆
Equipped with one CD-ROM and one
slim FDD ; support 3.5" HDD drive bays
◆
Can be vertically or horizontally
mounted, easy to fit into space limited
environment
◆
Fan direction changeable
◆
Replaceable air filter for easy cleaning
◆
One On/Off switch protection cap and
one touch free reset for secure access
◆
Equipped with front access USB ports
◆
One 12cm ball-bearing cooling fan
provides better ventilation to enhance
system reliability
◆
Built-in 125W ATX power supply
PNC-5063 is a compact and rugged 6-slot half-size node chassis
designed for space limited application. With the most economical space,
PNC-5063 provides you the maximum configuration. Its well-shield, wellcooled and user friendly access are specially designed to withstand
shocks, dust, humidity, trembling vibration and high operating
temperature in the harsh environment
General
Construction
Heavy-duty steel
Air Filter
One replaceable air filter at the front
door
Cooling Fan
Speaker
Input Frequency
One 8Ω speaker
47Hz - 63Hz
Standard Color
Input Current
Industrial dark gray
4A max./115V, 2A max./230V
Dimension
Efficiency
196(W) x 262(D) x 196(H) mm
7.72"(W) x 10.31"(D) x 7.2"(H)
Min. 65%
One 12cm (86.5cfm) ball-bearing fan
Weight
Disk Drive Housing
Net: 6.5kg (14.321lb)
Gross: 7kg (15.421lb)
External: One NB CD-ROM and
one NB FDD(Devices
built-in)
Internal: 3.5" HDD
Indicator
LED indicators for HDD
Switch
One for reset and one for power On/Off
with a protection cap
USB Connector
Two Front access USB ports
Backplane
Min. 100,000 hours at 75% max. output
at 25˚C ambient temperature
Safety
UL / CSA / TUV / CB / NEMKO
PBP-05P : 5-slot PCI backplane
Environment
Power Supply (ENP-0812A)
Maximum Output
125W
Operating Temperature Range
0 to +55˚C
Storage Temperature Range
Output Voltage & Current
0 to +70˚C
+3.3V@10A, +5V@12A,12V@3A,
[email protected],[email protected], 5VSB@2A
Relative Humidity
Input Voltage
AC 95 -132V
AC 180 - 264V
1
MTBF Reliability
5 to 95% non-condensing
PNC-5063
Advanced 6-slot Industrial Node Chassis for half-size PCI cards
What's New
Better ventilation and high
frequency CPU thermal issue
Well Shielding for EMI solution
Well Shielding for EMI solution
Fan noise eliminated by mechanical
design
Reserved certain CPU cooler space
for higher frequency CPU
Extra open slot for expansion
Engineering Drawing
Dustproof fan filter design
Ordering Guide
PNC-5063-05P-125X
6-slot node chassis, PBP-05P,
125W ATX PSU, 24X slim CD-ROM
and slim FDD
2
IRC-404S
Compact 4-slot Industrial Node Chassis
IRC-404S is a compact and rugged 4-slot
node chassis to be the industrial controller in
the space limited application. It is designed
for the diskless operation which needs the
best reliability and bears no peripherals'
errors.
Its rugged, sturdy, full-sealed and well-cooled
steel chassis is designed to withstand shock,
dust, humidity, vibration and high
temperature in the harsh environment.
General
Dimension
Input Current
Construction
110(W) x 218(D) x 195(H) mm
4.3"(W) x 8.6"(D) x 7.7"(H)
2A max./115V, 1A max./230V
Weight
Min. 70%
Heavy-duty steel
Air Filter
One replaceable filter inside the chassis
Cooling Fan
No fans needed
Disk Drive Housing
Net: 2.35kg (5.2lb)
Gross: 2.85kg (6.3lb)
MTBF Reliability
Min. 200,000 hours at 25˚C (70˚F)
Backplane
Safety
4-slot ISA Backplane
UL/CUL/TUV
One internal 2.5" HDD
Power Supply (MPE-8071)
Indicator
Maximum Output
LED indicators for HDD and power
On/Off
Switch
One for reset and one for power On/Off
Standard Color
Industrial dark gray
Efficiency
Environment
Operating Temperature Range
70W
0 to +55˚C
Output Voltage & Current
+5V@10A, [email protected],
[email protected]
Storage Temperature Range
Input Voltage
Relative Humidity
AC 85 - 264V
0 to +70˚C
5 to 95% non-condensing
Input Frequency
43Hz - 63Hz
Engineering Drawing
▲ Rear Side of IRC-404S
51
IRC-308
8-slot Full-size Industrial Node Chassis (Shoe-box)
IRC-308 is a compact and rugged 8-slot full-size node chassis
designed for space limited application. Its rugged, sturdy, full-sealed
and well-cooled steel chassis is specially designed to withstand shocks,
dust, humidity, trembling vibration and extremely operating temperature
in the harsh environments.
General
Construction
Heavy-duty steel
Air Filter
One replaceable air filter at the front
door
5.25" drive space for CD-ROM or mobile
rack, easy to install software and mirror
disk (RAID1)
◆
Replaceable air filter for easy cleaning
◆
Fan direction changeable
◆
Can be vertically or horizontally
mounted, easy to fit into space limited
environment
◆
One 12cm ball-bearing cooling fan for
better ventilation
◆
Two adjustable positions for hold-down
card retainers provide higher flexibility to
fix all the cards tightly
◆
Both 8-slot ISA and PICMG BP applicable,
easy to change to different Backplanes
◆
Field replaceable power supply bracket
for both normal PS/2 and PS/2 type
redundant PSU, easy for defective PSU
changing
Keyboard Connector Cap
Input Voltage
One cap for better security
95 - 130V/190 - 254V selectable
Speaker
Input Frequency
One 8Ω speaker
43Hz - 63Hz
Standard Color
Input Current
Beige, black
8A max./115V, 4A max./230V
Cooling Fan
Dimension
Efficiency
One 12cm (86.5cfm) ball-bearing fan
330(W) x 408(D) x 172(H) mm
13"(W) x 16.1"(D) x 6.8"(H)
Min. 70%
Weight
Min. 50,000 hours at 25˚C (70˚F)
Net: 9kg (19.8lb)
Gross: 10kg (22lb)
Safety
Disk Drive Housing
External: 5.25"x2+3.5" FDDx1
Internal: 3.5" HDDx1
Indicator
LED indicators for HDD and power
On/Off
Switch
One for reset and one for power On/Off
with a protection cap
Mounting Bracket
MTBF Reliability
UL/CSA/TUV/FCC/CE/CB
Backplane
8-slot ISA Backplane
8-slot PICMG (4xPCI) Backplane
8-slot PICMG (3xPCI) Backplane
Power Supply (PW-250)
Maximum Output
Two brackets for vertical and horizontal
mounting
250W
Keyboard Connector
Output Voltage & Current
Standard 5-pin AT K/B connector with a
cap
43
◆
+5V@25A, +12V@10A,
[email protected], [email protected]
Environment
Operating Temperature Range
0 to +55˚C
Storage Temperature Range
0 to +70˚C
Relative Humidity
5 to 95% non-condensing
IRC-308
8-slot Full-sized Industrial Node Chassis (Shoe-box)
Features
Benefits
◆
5.25" drive space for CD-ROM or mobile rack
◆
◆
Replaceable air filter
◆
For easy cleaning
◆
Can be vertically or horizontally mounted
◆
Easy to fit into different space limited environment
◆
Two adjustable positions for hold-down card retainer
◆
Fix all the cards more flexibly and tightly
◆
Both 8-slot ISA and PICMG Backplane are applicable
◆
Easy to change to different Backplane and keep stock
◆
Field replaceable power supply bracket for both normal
PS/2 PSU and PS/2 type redundant PSU
◆
Easy for maintenance
Need only 30 seconds to change the defective PSU module
◆
Easy to install software and mirror disk (RAID 1)
What's New
Redundant power supply
Can be mounted in different styles
Dual card retainers
With a new bracket, a PS/2 or redundant
PSU can be installed to enhance security.
IRC-308's front door can be changed for
either vertical or horizontal installation.
It has two positions for card clamps to hold
both PCI and ISA cards tightly.
Ordering Guide
Engineering Drawing
IRC-308-08I-25
8-slot full-size industrial node
chassis with 8-slot ISA Backplane
and 250W power supply
IRC-308-08P4-25
8-slot full-size industrial node
chassis with 4xPCI Backplane and
250W power supply
IRC-308-08P4-30X
8-slot full-size industrial node
chassis with 4xPCI Backplane and
300W ATX power supply
IRC-308-08P3-25
8-slot full-size industrial node
chassis with 3xPCI Backplane and
250W power supply
44
IRC-306
6-slot Full-size Industrial Node Chassis (Shoe-box)
IRC-306 is a compact and rugged 6-slot full-size node chassis
designed for space limited applications. Its rugged, sturdy, fullsealed and well-cooled steel chassis is specially designed to
withstand shocks, dust, humidity, trembling vibration and high
operating temperature in the harsh environment.
General
Construction
Heavy-duty steel
Air Filter
One external 5.25" and 3.5" and one
internal HDD drive bays
◆
Replaceable air filter for easy cleaning
◆
Can be vertically or horizontally mounted,
easy to fit into space limited environment
◆
One 12cm ball-bearing cooling fan for
better ventilation
◆
Fan direction changeable
◆
Two adjustable positions for hold-down
card retainers provide better protection
from vibration
◆
Both 6-slot ISA and PICMG BP applicable,
easy to change to different Backplanes
◆
Field replaceable power supply bracket for
both normal PS/2 and PS/2 type redundant
PSU, easy for defective PSU changing
Keyboard Connector Cap
Input Voltage
One cap for better security
95 - 130V/190 - 254V selectable
Speaker
Input Frequency
One 8Ω speaker
43Hz - 63Hz
One replaceable air filter at the front
door
Standard Color
Input Current
Beige
8A max./115V, 4A max./230V
Cooling Fan
Dimension
Efficiency
One 12cm (86.5cfm) ball-bearing fan
260(W) x 408(D) x 172(H) mm
10.2"(W) x 16.1"(D) x 6.8"(H)
Min. 70%
Weight
Min. 50,000 hours at 25˚C (70˚F)
Net: 8.5Kg.(18.7 lb)
Gross: 9.5Kg.(20.9 lb)
Safety
Disk Drive Housing
External: 5.25"x1+3.5" FDDx1
Internal: 3.5" HDDx1
Indicator
LED indicators for HDD and power
On/Off
Switch
One for reset and one for power On/Off
with a protection cap
Mounting Bracket
MTBF Reliability
UL/CSA/TUV/FCC/CE/CB
Backplane
6-slot ISA Backplane
6-slot PICMG (4xPCI) Backplane
6-slot PICMG (3xPCI) Backplane
Power Supply (PW-250)
Maximum Output
Two brackets for vertical and horizontal
mounting
250W
Keyboard Connector
Output Voltage & Current
Standard 5-pin AT K/B connector with a
cap
45
◆
+5V@25A, +12V@10A,
[email protected], [email protected]
Environment
Operating Temperature Range
0 to +55˚C
Storage Temperature Range
0 to +70˚C
Relative Humidity
5 to 95% non-condensing
IRC-306
6-slot Full-sized Industrial Node Chassis (Shoe-box)
Features
Benefits
◆
5.25" drive space for CD-ROM or mobile rack
◆
Easy to install software
◆
Replaceable air filter
◆
For easy cleaning
◆
Can be vertically or horizontally mounted
◆
Easy to fit into different space limited environment
◆
Two adjustable positions for hold-down card retainer
◆
Fix all the cards more flexibly and tightly
◆
Both 6-slot ISA and PICMG Backplane are applicable
◆
Easy to change to different Backplane and keep stock
◆
Field replaceable power supply bracket for both normal
PS/2 PSU and PS/2 type redundant PSU
◆
Easy for maintenance
Need only 30 seconds to change the defective PSU module
◆
What's New
Redundant power supply
Can be mounted in different styles
Dual card retainers
With a new bracket, a PS/2 or redundant
PSU can be installed to enhance reliability.
IRC-306's front door can be changed for
either vertical or horizontal installation.
It has two positions for card clamps to hold
both PCI and ISA cards tightly.
Ordering Guide
Engineering Drawing
IRC-306-06I-25
6-slot full-size industrial node
chassis with 6-slot ISA Backplane
and 250W power supply
IRC-306-06P4-25
6-slot full-size industrial node
chassis with 6-slot 4xPCI
Backplane and 250W PSU
IRC-306-06P3-25
6-slot full-size industrial node
chassis with 6-slot 3xPCI
Backplane and 250W PSU
46
IRC-306S
6-slot Industrial Node Chassis with NB CD-ROM, FDD and HDD
IRC-306S is a compact and rugged 6-slot node chassis for industrial
controller in the space limited application. Since CD-ROM is the most
common device for installing s/w, it is equipped with a notebook PC CDROM drive for easy installation of the necessary OS or application s/w.
Its rugged, sturdy, full-sealed and well-cooled steel chassis is designed
to withstand heavy shock, dust, humidity, vibration and high temperature
in the harsh environments.
General
Construction
Heavy-duty steel
Support one 5.25" drive bay for
EZDRV-300 or other kind of device
◆
Can be vertically or horizontally
mounted, easy to fit into space limited
environment
◆
Fan direction changeable
◆
Replaceable air filter for easy cleaning
◆
One On/Off switch protection cap and
one touch free reset for secure access
◆
Equipped with one K/B connector cap to
prevent the front K/B connector from the
dust
◆
One 12cm ball-bearing cooling fan
provides better ventilation to enhance
system reliability
◆
Built-in 130W power supply
Speaker
Input Frequency
One 8Ω speaker
43Hz - 63Hz
Standard Color
Input Current
Black, beige
8A max./115V, 4A max./230V
Dimension
Efficiency
135(W) x 256.7(D) x 188(H) mm
5.3"(W) x 10.1"(D) x 7.4"(H)
Min. 70%
One 12cm (86.5cfm) ball-bearing fan
Weight
Min. 50,000 hours at 25˚C (70˚F)
Disk Drive Housing
Net: 5.5kg (12.1lb)
Gross: 6kg (13.2lb)
Safety
Air Filter
One replaceable air filter at the front
door
Cooling Fan
External: NB CD-ROMx1+NB FDDx1
Internal: NB 2.5" FDDx1
Indicator
LED indicators for HDD and power
On/Off
Switch
One for reset and one for power On/Off
with a protection cap
Keyboard Connector
Standard PS/2 K/B connector at the rear
panel
Keyboard Connector Cap
One cap at the rear panel
47
◆
MTBF Reliability
UL/CSA/TUV/CE
Backplane
6-slot ISA Backplane
6-slot PICMG PISA bus Backplane
Environment
Power Supply (ORION-130ATX)
0 to +55˚C
Maximum Output
135W
Output Voltage & Current
+5V@15A, +12V@6A, +3.3V@6A
[email protected], -12V@1A, +5VSB@1A
Input Voltage
90 - 132V/180 - 264V selectable
Operating Temperature Range
Storage Temperature Range
0 to +70˚C
Relative Humidity
5 to 95% non-condensing
IRC-306S
6-slot Industrial Node Chassis with NB CD-ROM, FDD and HDD
Features
Benefits
◆
Replaceable air filter
◆
ON/OFF switch protection cap
◆
Avoid accidental reset of system
◆
K/B connector cap included
◆
For dust-proof for the front K/B connector
◆
One 12cm ball-bearing cooling fan
◆
Better ventilation to enhance system reliability
◆
For easy cleaning
What's New
Can be mounted in different styles
Touch-free ON/OFF & reset switch
The rear of IRC-306S
IRC-306S allows for vertical and horizontal
installation.
For security concerns, a switch protection
cap is provided to prevent accidental reset.
IRC-306S has well-cooling design to expire
the heat from the system.
Ordering Guide
Engineering Drawing
IRC-306S-06I-135
6-slot node chassis with 6-slot ISA
Backplane and 135W power
supply
48
IRC-304S
Advanced 4-slot Industrial Node Chassis for Both ISA or PCI SBC
◆
IRC-304S is a compact and rugged 4-slot node chassis for industrial
controller in the space limited application. Since CD-ROM is the most
common device for installing s/w, it is equipped with a notebook PC type
CD-ROM drive for easy installation of the necessary OS or application
software.
One CD-ROM, FDD and 2.5" HDD (all
slim type) and one 3.5" HDD drive bays
◆
Can be vertically or horizontally
mounted, easy to fit into space limited
environment
◆
Fan direction changeable
◆
Replaceable air filter for easy cleaning
◆
One On/Off switch protection cap and
one touch free reset for secure access
◆
Equipped with one K/B connector cap to
prevent the front K/B connector from the
dust
◆
One 12cm ball-bearing cooling fan
provides better ventilation to enhance
system reliability
◆
Built-in MPE-8071 70W power supply
Its rugged, sturdy, full-sealed and well-cooled steel chassis is designed
to withstand shock, dust, humidity, vibration and high temperature in the
harsh environment.
General
Speaker
Input Frequency
One 8Ω speaker
43Hz - 63Hz
Construction
Heavy-duty steel
Standard Color
2A max./115V, 1A max./230V
Dimension
Efficiency
172(W) x 256.7(D) x 172(H) mm
6.8"(W) x 10.1"(D) x 6.8"(H)
Min. 70%
One 12cm (86.5cfm) ball-bearing fan
Weight
Min. 200,000 hours at 25˚C (70˚F)
Disk Drive Housing
Net: 5kg (11lb)
Gross: 5.5kg (12.1lb)
Air Filter
One replaceable air filter at the front
door
Cooling Fan
External: NB CD-ROMx1+NB FDDx1
Internal: NB 2.5" HDDx1+3.5" HDDx1
Indicator
Switch
One for reset and one for power On/Off
with a protection cap
Keyboard Connector
Standard 5-pin AT K/B connector at the
rear panel
Keyboard Connector Cap
One cap at the rear panel
MTBF Reliability
Safety
ULC/UL/TUV
Backplane
PBP-04I: 4-slot ISA backplane
Environment
Power Supply (MPE-8071)
0 to +55˚C
LED indicators for HDD
1
Input Current
Industrial dark gray
Operating Temperature Range
Maximum Output
Storage Temperature Range
70W
0 to +70˚C
Output Voltage & Current
Relative Humidity
+5V@10A, [email protected],
[email protected]
Input Voltage
AC 85 - 264V
5 to 95% non-condensing
IRC-304S
Advanced 4-slot Industrial Node Chassis with NB CD-ROM, FDD and HDD
Features
Benefits
◆
Replaceable air filter
◆
ON/OFF switch protection cap
◆
Avoid accidental reset of system
◆
K/B connector cap included
◆
For dust-proof for the front K/B connector
◆
One 12cm ball-bearing cooling fan
◆
Better ventilation to enhance system reliability
◆
For easy cleaning
What's New
Moveable card guide for both PCI and
ISA position
Maximum expandability in limited space
for 3.5" HDD
Removable fan filter for easy-cleaning
Can be vertically or horizontally mounted
Friendly design for easy assembly
4-slot ISA passive BP installable (PBP-04I)
Engineering Drawing
Ordering Guide
IRC-304S-04I-70
4-slot node chassis with 4-slot ISA
backplane and 70W power supply
* CD-ROM & FDD are optional items,
not included in standard models
Portwell, Inc.
American Portwell Technology, Inc.
Portwell Japan, Inc.
3F, No. 92, Nei-Hu Rd., Sec.1
114 Taipei, Taiwan, R.O.C.
Te l : +886-2-2799-2020
Fax: +886-2-2799-1010
E-amil: [email protected]
http://www.portwell.com.tw
38507 Cherry St., Suite D
Newark, CA 94560
Te l : (510)790-9192
Fax: (510)790-9191
E-mail: [email protected]
http://www.portwell.com
101-0042 Ueda Build. 7F, 10-2 Kanda higashi
matsushita-cho chiyoda-ku Tokyo Japan
Te l : +81-3-5298-8071
Fax: +81-3-5298-8072
E-mail: [email protected]
http://www.portwell.co.jp
2
N+1 Redundant PSU
ORION-2253
ORION-2003
ORION-2004
Advanced 450W+225W (N+1) PS/2 Type Hot-Swap Redundant Power Supply
400W+200W Load Sharing (N+1) Hot-swap Power Supply
600W+200W (N+1) Redundant Switching Power Supply
1+1 Redundant PSU
ORION-2302
ORION-3002
ORION-F30020
ORION-3005H/4005H
ORION-F4002
BPS-270RD/270RDX
BPS-250RDDX/48
230W for 2U Slim Type ATX Hot-Swap Redundant Power Supply
Advanced 300W PS/2 Type Hot-Swap Redundant Power Supply
300W+300W PS/2 Active PFC Redundant Power Supply
400W+400W/300W+300W Horizontal Type ATX Redundant Power Supply
400W+400W Dual PS/2 Active PFC Redundant Power Supply
270W PS/2 Type Hot Swap Redundant Power Supply
-48V Input 450W PS/2 Type DC/DC Hot Swap Redundant Power Supply
PS/2 Size PSU
PW-250/380
ORION-330A
PW-300ATX
PW-330ATXE-12V
ORION-3001PY
ORION-450AX
ORION-300DX/24/48
ORION-48T
Standard PS/2 380W/250W Power Supply
Full 330W Single PS/2 AT Power Supply with Auto-range Input
Standard PS/2 300W Power Supply
330W PS/2 Power Supply for Pentium® 4 Processor Solution
Full 300W PS/2 Active PFC Power Supply
Full 450W Single PS/2 ATX Power Supply with Auto-range Input
48V&24V DC Input PS/2 DC/DC Converter with ATX Output
48V DC Output Power Supply Tester
Slim Size PSU
ORION-300S
ORION-400S
ORION-150AX
ORION-250S
Slim Type of 300W ATX Power Supply
Slim Type of 400W ATX Power Supply
Slim Type of 150W ATX Power Supply
Slim Type of 250W ATX Power Supply
Open Frame PSU
BPS-7004/24/12
70W Open-frame +24V or +12V DC/DC Power Supply
Power Cable
CABLE-EXT-ATX
CABLE-EXT-AT
CABLE-ATX-P8P9
CABLE-HDD-P4
Extension Cable for ATX to ATX+P8/P9 Connectors
Extension Cable for P8/P9 Connectors
Cable for ATX to P8/P9 Connectors Converting
P4 power adapter cable
ORION-2004
600W+200W (N+1) Redundant Switching Power Supply
Features
Values / Benefits
Apply true load-sharing N+1 design
High reliability & redundancy
Four 200W Hot-swap redundant modules
Alarm beeping and LED indicator
Provide 1.5A for stand-by +5V
+3.3V on each module
+5V,+12V,+3.3V o/p have OVP design
2-Layer, FR-4, 94-V0 PCB
Silver plated Germany DIN connector
Ball bearing NMB fan
Use 15A/400V power transistor
2 pcs of 30A/40V parallel for +5V diode
20A/200V (Fuji D92-02) for +12V diode
Varistor installed
Total 800W for heavy loading system
Easy for maintenance
Meet ATX2.01 Spec. for newest ATX M/B
Real redundant design for +3.3V output
No worry for any DC o/p damage
Good reliability for industrial grade PSU
Extra reliability for high current situation
Good reliability
High current tolerance with longer durability
Durability twice better than normal PSU
Durability twice better than normal PSU
Absorb more inrush spike
Remote sense installed
Output power connector
Auto-adjust M/B loading & o/p voltage
One ATX & one P8P9 connector
ORION-2004 is a "state-of-the-art" design to the
traditional power supply market. It is smart not only in
the PSU circuit design, but also in the mechanical
design. Besides, it is easy to hot swap the modules.
Together with its compactness, it brings a lot of benefits
to customers in non-stop computing environment.
The "N+1" load sharing technology is the trend for highend switching power module. With this feature,
customers can expand the power on their demand. It
surely meets the growing demand for the mission critical
application.
Specifications
◆
Input
Voltage
Frequency
Current
Max. Load
Min. Load
Max. Watt.
Load Reg.
Cross Reg.
Line Reg.
Ripple
Noise
◆
DC Output
◆
◆
Efficiency
Holdup Time
◆
Hi-Pot Test
◆
Over Voltage Protection
Over Load Protection
MTBF
◆ EMI & Safety Approval
◆
◆
◆
Temperature/Humidity
◆
Dimension (WxDxH)
90V ~ 132V, 180 ~ 264V selectable
47 ~ 63 Hz
15A@115V, 8A@230V
+5V
+3.3V +12V -5V
-12V
60A
48A
20A
1A
1A
3A
0.3A 0.5A 0A
0A
580W
5W
12W
+/-5% +/-4% +/-5% +/-10% +/-10%
+/-5% +/-4% +/-5% +/-10% +/-10%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-2% +/-2%
> 65%
16ms. at full load
1.5KVRMS, 60sec. from i/p to ground
3.0KVRMS, 60sec. from i/p to o/p
+5V: 5.6V ~ 6.5V/+3.3V: 3.8V ~ 4.3V
+12V: 13.6V ~ 15.6V
Total o/p 110% ~ 130%
> 100,000hrs
TUV, UL, CE, FCC
Operating : 0 ~ 50˚C, 20 ~ 90%RH
Storage : -20 ~ 60˚C, 5 ~ 95%RH
100x210x214.1 mm / 4"x8.3"x8.4"
Engineering Drawing
Ordering Guide
●
600W+200W (N+1) redundant PSU (total 800W output),
with one ATX & one P8P9 output connectors
●
ORION-2004-S (for SunSPARC AXmp)
600W+200W (N+1) redundant PSU (total 800W output),
with one 24-pin ATX and one 20-pin ATX connectors
●
53
ORION-2004
PFC-Kit-2004 (Optional)
Passive-kit for ORION-2004
ORION-2003
400W+200W (N+1) Redundant Switching Power Supply
Features
Values / Benefits
Apply true load-sharing N+1 design
Three 200W hot-swap redundant modules
High reliability & redundancy
Total 600W for heavy loading system
Alarm beeping and LED indicator
Provide 1.5A for stand-by +5V
Easy for maintenance
Meet ATX2.01 Spec. for newest ATX M/B
+3.3V on each module
+5V,+12V,+3.3V o/p have OVP design
2-Layer, FR-4, 94-V0 PCB
Real redundant design for +3.3V output
No worry for any DC o/p damage
Good reliability for industrial grade PSU
Silver plated German DIN connector
Ball-bearing NMB fan
Use 15A/400V power transistor
2 pcs of 30A/40V parallel for +5V diode
20A/200V (Fuji D92-02) for +12V diode
Extra reliability for high current situation
Good reliability
High current tolerance with longer durability
Durability twice better than normal PSU
Durability twice better than normal PSU
Varistor installed
Remote sense installed
Output power connector
Absorb more inrush spike
Auto-adjust M/B loading & o/p voltage
One ATX & one P8P9 connector
ORION-2003 is a "state-of-the-art" design to the
traditional power supply market. It is smart not only in
the PSU circuit design, but also in the mechanical
design. Besides, it is easy to hot swap the modules.
Together with its compactness, it brings a lot of benefits
to customers in non-stop computing environment.
The "N+1" load sharing technology is the trend for highend switching power module. With this feature,
customers can expand the power on their demand. It
surely meets the growing demand for the mission critical
application.
Specifications
◆
Input
Voltage
Frequency
Current
Max. Load
Min. Load
Max. Watt.
Load Reg.
Cross Reg.
Line Reg.
Ripple
Noise
◆
DC Output
◆
◆
Efficiency
Holdup Time
◆
Hi-Pot Test
◆
Over Voltage Protection
Over Load Protection
MTBF
◆ EMI & Safety Approval
◆
◆
◆
Temperature/Humidity
◆
Dimension (WxDxH)
90V ~ 132V, 180 ~ 264V selectable
47 ~ 63 Hz
9A@115V, 5A@230V
+5V
+3.3V +12V -5V
-12V
40A
32A
14A
1A
1A
3A
0.3A 0.5A 0A
0A
380W
5W
12W
+/-5% +/-4% +/-5% +/-10% +/-10%
+/-5% +/-4% +/-5% +/-10% +/-10%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-2% +/-2%
> 65%
20ms. at full load
1.5KVRMS, 60sec. from i/p to ground
3.0KVRMS, 60sec. from i/p to o/p
+5V: 5.6V ~ 6.5V/+3.3V: 3.8V ~ 4.3V
+12V: 13.6V ~ 15.6V
Total o/p 110% ~ 130%
> 100,000hrs
TUV, UL, CE, FCC
Operating : 0 ~ 50˚C, 20 ~ 90%RH
Storage : -20 ~ 60˚C, 5 ~ 95%RH
100x210x170 mm / 4"x8.3"x6.7"
Engineering Drawing
Ordering Guide
●
ORION-2003
400W+200W (N+1) redundant PSU (total 600W output),
with one ATX & one P8P9 output connectors
54
ORION-2253
Advanced 450W+225W (N+1) PS/2 Type Hot-Swap Redundant Power Supply
PS/2 type PSU is the default standard for all chassis
manufacturers. Keeping the same size makes it easy
for the PSU suppliers to find the market. As the
computing power is enhanced, the demand for higher
power output comes. It is easy to increase the power
output by extending its size, but not easy to have
redundant capability and keep it in an exact PS/2 size
at the same time.
ORION-2253 shows the technology to meet
customers' requirements without sacrificing any
advantages of traditional PS/2 power supplies. With
the "N+1" design, the total power output of ORION2253 can be more than 675W and has 450W output
when any module fails.
Ordering Guide
●
ORION-2253
Advanced 450W+225W (N+1) PS/2 type
hot-swap redundant power supply with ATX
output
Features
Values / Benefits
Apply true load-sharing N+1 design
Three 225W hot-swap redundant modules
Alarm beeping and LED indicator
Provide 2.5A for stand-by +5V
+3.3V on each module
+5V,+12V,+3.3V o/p have OVP design
2-Layer, FR-4, 94-V0 PCB
Ball-bearing fan
High reliability & redundancy
Total 675W for heavy loading system
Easy for maintenance
Meet ATX2.03 Spec. for newest ATX M/B
Real redundant design for +3.3V output
No worry for any DC o/p damage
Good reliability for industrial grade PSU
Good reliability
Varistor installed
Remote sense installed
Absorb more inrush spike
Auto-adjust M/B loading & o/p voltage
Specifications
◆
Input
Voltage
Frequency
Current
Max. Load
Min. Load
Max. Watt.
Load Reg.
Cross Reg.
Line Reg.
Ripple
Noise
◆
DC Output
◆
◆
Efficiency
Holdup Time
◆
Hi-Pot Test
◆
Over Power Protection
Over Load Protection
MTBF
◆ Safety Approval
◆
◆
57
◆
Temperature/Humidity
◆
Dimension (WxDxH)
AC 95 ~ 132V, 180 ~ 264V selectable
47 ~ 63 Hz
12A@115V, 6A@230V
+5V
+3.3V +12V -5V
-12V
45A
25A
25A
1A
2A
3A
0A
1A
0A
0A
410W
5W
24W
+/-5% +/-6% +/-5% +/-10% +/-10%
+/-5% +/-6% +/-5% +/-10% +/-10%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-2% +/-2%
> 75%
16ms. at full load
1.5KVRMS, 60sec. from i/p to ground
3.0KVRMS, 60sec. from i/p to o/p
+5V: 5.6V ~ 6.5V/+3.3V: 3.8V ~ 4.3V
+12V: 13.6V ~ 15.6V
Total o/p power over 120%
> 167,000hrs
UL, TUV, CE, FCC
Operating : 0 ~ 50˚C, 20 ~ 90%RH
Storage : -20 ~ 60˚C, 5 ~ 95%RH
86x181x150 mm / 3.4"x7.1"x5.9"
Engineering Drawing
ORION-2302
230W for 2U Slim Type ATX Hot-Swap Redundant Power Supply
ORION-2302 is a compact redundant power
supply for "Mission Critical" applications. As
"High Availability" becomes a common
requirement, now the redundant power supply is
part of non-stop computers. With its compact
size, ORION-2302 can be easily applied to get
great added value of "High Availability" without
changing any mechanism or redesigning
systems.
Specifications
◆
◆
Input
DC Output
Voltage
Frequency
Current
Max. Load
Min. Load
Max. Watt.
Load Reg.
Cross Reg.
Line Reg.
Ripple
Noise
◆
Efficiency
Holdup Time
◆
Hi-Pot Test
◆
Over Voltage Protection
◆
Over Power Protection
MTBF
◆ Safety Approval
◆
◆
◆
Temperature/Humidity
◆
Dimension (WxDxH)
AC 95 ~ 132V, 180 ~ 264V selectable
47 ~ 63 Hz
4A@115V, 2A@230V
+5V
+12V +3.3V -5V
-12V
25A
13A
15A
0.5A 1A
3A
1A
0A
0A
0A
210W
14.5W
+/-5% +/-6% +/-5% +/-10% +/-10%
+/-5% +/-6% +/-5% +/-10% +/-10%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-2% +/-2%
> 75% at full load
16ms. at full load
1.5KVRMS, 60sec. from i/p to ground
3.0KVRMS, 60sec. from i/p to o/p
+5V: 5.6V ~ 6.5V/+12V: 12.6V ~ 15.6V
+3.3V: 3.7V ~ 4.5V
Total o/p 120%
> 176,000hrs
UL, CUL, TUV, CE
Operating : 0 ~50˚C, 20 ~90%RH
Storage : -20 ~60˚C, 5 ~95%RH
86x181x109 mm / 3.4"x7.1"x4.3"
Features
The most compact hot swap redundant PSU to fit into a
limited space, suitable for 2U chassis
Two 230W hot-swap redundant modules provide 460W output
for the new computers high-frequency CPUs
Provide 1.5A for standby +5V
High reliable ball bearing sensitive fan
Equipped with 4-ear brackets for fixing the PSU easily and
flexibly
Alarm beeping and LED indicator of defective module for
field replacement directly
Enhanced swappable fan to get high security for 100%
mission critical application
Engineering Drawing
Ordering Guide
●
ORION-2302
230W for 2U slim type ATX redundant PSU
58
ORION-3002
Advanced 300W PS/2 Type Hot-Swap Redundant Power Supply
PS/2 type PSU is the default standard for all chassis
manufacturers. Keeping the same size makes it easy
for the PSU suppliers to find the market. As the
computing power is enhanced, the demand for
higher power output comes. It is easy to increase the
power output by extending its size, but not easy to
have redundant capability and keep it in an exact
PS/2 size at the same time.
ORION-3002 shows the technology to meet
customers' requirements without sacrificing any
advantages of traditional PS/2 power supplies. With
the "Dual Redundant" design, the total power output
of ORION-3002 can be more than 600W and has
300W output when any module fails.
Ordering Guide
●
ORION-3002-X
Advanced 300W PS/2 type hot-swap
redundant power supply with ATX output
●
ORION-3002-T
Advanced 300W PS/2 type hot-swap
redundant power supply with AT output
●
ORION-3002-R
Advanced 300W PS/2 type hot-swap
redundant power supply for RAID
Features
Values / Benefits
Apply true load-sharing N+1 design
High reliability & redundancy
Two 300W hot-swap redundant modules
Alarm beeping and LED indicator
Provide 2A for stand-by +5V
+3.3V on each module
+5V,+12V,+3.3V o/p have OVP design
2-Layer, FR-4, 94-V0 PCB
Ball-bearing fan
Remote sense installed
Total 600W for heavy loading system
Easy for maintenance
Meet ATX2.01 Spec. for newest ATX M/B
Real redundant design for +3.3V output
No worry for any DC o/p to damage
Good reliability for industrial grade PSU
Good reliability
Auto-adjust M/B loading & o/p voltage
PS: Front loading type power supply available
Specifications
◆
Input
◆
DC Output
◆
◆
Efficiency
Holdup Time
◆
Hi-Pot Test
Voltage
Frequency
Current
Max. Load
Min. Load
Max. Watt.
Load Reg.
Cross Reg.
Line Reg.
Ripple
Noise
Over Voltage Protection
Over Load Protection
◆ MTBF
◆ Safety Approval
◆
◆
◆
Temperature/Humidity
◆
Dimension (WxDxH)
Engineering Drawing
AC 90 ~ 132V, 180 ~ 264V Auto-range
47 ~ 63Hz
6A@115V, 3A@230V
+5V
+3.3V +12V -5V
-12V
36A
16A
14A
0.5A 1A
3A
1A
1A
0A
0A
280W
2.5W 6W
+/-5% +/-5% +/-5% +/-10% +/-10%
+/-5% +/-5% +/-5% +/-10% +/-10%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-2% +/-2%
> 65%
20ms. at full load
1.5KVRMS, 60sec. from i/p to ground
3.0KVRMS, 60sec. from i/p to o/p
+5V: 5.6V ~ 6.5V/+12V: 13.6V ~ 15.6V
Total o/p 120% ~ 140%
> 100,000hrs
UL, TUV, CE, FCC
Operating : 0 ~ 50˚C, 20 ~ 90%RH
Storage : -20 ~ 60˚C, 5 ~ 95%RH
86x175x150 mm / 3.4"x6.9"x5.9"
56
ORION-F30020
PS/2 type 300W+300W Active PFC Redundant Power Supply
Orion-F30020 is the most up-to-date Power Supply
to meet high-end application system. It's a PS/2
type redundant power supply with ATX (Ver. 2.03)
output and active PFC design to meet the
environmental protection needs. Its very reliable
design makes it not only fit normal computing
system requests, but also meet certain critical
applications.
Specifications
Features
Support Intel P4 CPU
Real active PFC design for both 110V/230V
Full range AC input 90V~240V
PS/2 type for good feasibility
Dual AC inlet type available
Front access type available
◆
Input
Voltage
Frequency
Current
◆
DC Output
Max. Load
Min. Load
Max. Watt.
Efficiency
Holdup Time
◆ Hi-Pot Test
◆
Application
rack-mount system
Industrial computer
◆
Over Voltage Protection
Over Circuit Protection
◆Over Load Protection
◆ MTBF
◆
◆
◆
Temperature/Humidity
◆
Safety Approval
Dimension (WxDxH)
◆
100~240 VAC +/-10%, Full Range
47~63 Hz
Max. 6A/90VAC
+5V
+12V
-5V
-12V
+5VSB
+3.3V
30A
15A
0.3A
0.8A
2A
28A
2A
0.5A
0A
0A
0A
0.3A
+5V/+3.3V Max. 180W , +5V/+3.3V/+12V Max.280W
> 65% at full load
16ms minimum with full load
1500VRMS, 50Hz, 1 min., from input to ground.
3000VRMS, 50Hz, 1 min., from input to outputs.
+5V: 5.7V~6.5V, +3.3V: 3.9V~4.5V, +12V: 13.3V~14.5V
Shut Down Power Supply
Total Output 120% - 140%
> 100,000hrs
Operating: +0 ~ +50˚C, 20%~90% non-condensing at 40˚C
Storage: -20 ~ +60˚C, 5% ~ 95% non-condensing at 50˚C
UL / TUV / CSA / CE
150 x 85 x 227 mm, PS/2 type
Ordering Guide
●
ORION-F30020
PS/2 type 300W+300W Active PFC Redundant Power Supply
Portwell, Inc.
American Portwell Technology, Inc.
Portwell Japan, Inc.
3F, No. 92, Nei-Hu Rd., Sec.1
114 Taipei, Taiwan, R.O.C.
Te l : +886-2-2799-2020
Fax: +886-2-2799-1010
E-amil: [email protected]
http://www.portwell.com.tw
38507 Cherry St., Suite D
Newark, CA 94560 USA
Te l : (510)790-9192
Fax: (510)790-9191
E-mail: [email protected]
http://www.portwell.com
101-0042 Ueda Build. 7F, 10-2 Kanda higashi
matsushita-cho chiyoda-ku Tokyo Japan
Te l : +81-3-5298-8071
Fax: +81-3-5298-8072
E-mail: [email protected]
http://www.portwell.co.jp
ORION-4005H/3005H
400W+400W/300W+300W Horizontal Type ATX Redundant Power Supply
ORION-4005H is a horizontal type dual
PS/2 redundant power supply with
ATX (Ve r. 2.01) output for "Mission
Critical" applications.
The power supply is designed with
separate AC inputs to get zero down
time for real-time disaster recovery
and the remote DC sense to have the
best reliability for the non-stop
computing systems.
Ordering Guide
●
ORION-4005H
400W+400W dual PS/2 type ATX redundant
power supply
●
ORION-3005H
Features
Values / Benefits
Apply true load-sharing N+1 design
Two 400W hot-swap redundant modules
High reliability & redundancy
Total 800W for heavy loading system
Alarm beeping and LED indicator
Pass the 72 hrs 400W load burn-in test
Provide 1A for stand-by +5V
+3.3V on each module
Each DC o/p voltage has OCP design
Easy for maintenance
Real & full 400W redundant PSU
Meet ATX2.01 for newest ATX M/B
Real redundant design for +3.3V output
No worry for any DC o/p damage
+5V,+12V,+3.3V o/p have OVP design
Dual AC input
No failure on each DC o/p short test
AC input redundancy for safety
2-Layer, FR-4, 94-V0 PCB
Ball-bearing NMB fan
Use 3A components for -5V / -12V
Good reliability for industrial grade PSU
Good reliability
Suitable for CTI systems
Use 15A/400V power transistor
2 pcs of 30A/40V parallel for +5V diode
20A/200V (Fuji D92-02) for +12V diode
Varistor installed
Remote sense installed
High current tolerance w/ longer durability
Durability twice better than normal PSU
Durability twice better than normal PSU
Absorb more inrush spike
Auto-adjust M/B loading & o/p voltage
300W+300W dual PS/2 type ATX redundant
power supply
Specifications
◆
55
Input
Voltage
Frequency
Current
Max. Load
Min. Load
Max. Watt.
Load Reg.
Cross Reg.
Line Reg.
Ripple
Noise
◆
DC Output
◆
◆
Efficiency
Holdup Time
◆
Hi-Pot Test
◆
Over Voltage Protection
◆
◆
Over Load Protection
MTBF
◆
Temperature/Humidity
◆
Dimension (WxDxH)
AC 90 ~ 132V, 180 ~ 264V selectable
47 ~ 63 Hz
9A@115V, 5A@230V
+5V
+12V +3.3V -5V
-12V
50A
15A
30A
1.5A 1.5A
3A
1A
0A
0A
0A
370W
7.5W 18W
+/-5% +/-5% +/-5% +/-5% +/-5%
+/-5% +/-5% +/-5% +/-10% +/-5%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-2% +/-2%
> 70%
20ms. at full load
1.5KVRMS, 60sec. from i/p to ground
3.0KVRMS, 60sec. from i/p to o/p
+5V: 5.6V ~ 6.5V/+3.3V: 3.8V ~ 4.3V
+12V:13.6V ~ 15.6V
Total o/p 110% ~ 130%
> 100,000hrs
Operating : 0 ~ 50˚C, 20 ~ 90%RH
Storage : 0 ~ 70˚C, 5 ~ 95%RH
353x201x105 mm / 13.9"x7.9"x4.1"
Engineering Drawing
ORION-F4002
400W+400W Dual PS/2 Active PFC Redundant Power Supply
ORION-F4002 is the latest Power Supply that meets EC's requirements for the Harmonics EN-61000-3-2.
With the active PFC function, it not only conforms to the EC's standard, but also has a more flexible fullrange AC power input. In addition, the dual IEC inlet design is compliant with ISP's requirements to ensure
the stability of power input. The reliable design makes it fit into normal computing system as well as certain
critical applications.
Features
Support Intel ® P4 processor
Real active PFC design for both
110V/230V
Full-range AC input 90V~240V
Dual PS/2 type for good feasibility
Dual AC inlet
Hot swappable
Applications
IPC system
CTI system
Specifications
Voltage
Frequency
Current
◆
Input
◆
DC Output
◆
◆
Efficiency
Hold up Time
◆
Hi-Pot Test
◆
Over Voltage Protection
Max. Load
Min. Load
Max.Watt
Over Circuit Protection
Over Load Protection
◆ MTBF
◆ Temperature/Humidity
◆
◆
◆
◆
Safety Approval
Dimension (WxDxH)
100~240 VAC +/- 10%, full-range
47~ 63 Hz
Max. 6A/115V AC, 5A/230V AC
+5V
+12V
-5V
-12V
+5VSB
+3.3V
45A
18A
0.3A
0.8A
2A
30A
3A
1A
0A
0A
0A
0A
+5V/+3.3V/+12V max. 370W
> 65% at full load
20ms minimum at full load
1500VRMS, 50Hz, 60 sec., from i/p to ground
3000VRMS, 50Hz, 60 sec., from i/p to o/p
+5V: 5.6V~6.5V, +3.3V: 3.8V~4.3V,
+12V: 13.6V~15.6V
Shut down power supply when overloaded
110% ~ 130% on +3.3V/+5V, 120% ~ 150% on +12V
100,000 hrs at 25˚C
Operating: +0~ 50˚C, 20%~90% non-condensing at 40˚C
Storage: -20˚C ~ +60˚C, 5% ~ 95% non-condensing at 50˚C
UL, TUV, CB, CE
353x201x105 mm / 13.9"x7.9"x4.1" (dual PS/2 type)
Ordering Guide
●
ORION-F4002
400W+400W dual PS/2 active PFC redundant power supply
Portwell, Inc.
American Portwell Technology, Inc. eMCA (UK) Ltd.
Portwell Japan, Inc.
3F, No. 92, Nei-Hu Rd., Sec.1
114 Taipei, Taiwan, R.O.C.
Te l : +886-2-2799-2020
Fax: +886-2-2799-1010
E-amil: [email protected]
http://www.portwell.com.tw
38507 Cherry St., Suite D
Newark, CA 94560 USA
Te l : (510)790-9192
Fax: (510)790-9191
E-mail: [email protected]
http://www.portwell.com
E101-0042 Ueda Build. 7F, 10-2
Kanda higashi matsushita-cho
chiyoda-ku Tokyo Japan
Tel: +81-3-5298-8071
Fax: +81-3-5298-8072
E-mail: [email protected]
http://www.portwell.co.jp
* Specifications are subject to change without notice.
* Pentium 4 is a registered trademark of Intel Corporation.
Unit 30, Basepoint Enterprise Centre
Stroudley Road, Basingstoke,
Hampshire, RG24 8UP UK
Tel: +44-1256-406688
Fax: +44-1256-406689
E-mail: [email protected]
http://www.emca.co.uk
* Other trademarks, logos, brand names and company names are the
property of their respective owners.
BPS-270RD/270RDX
270W PS/2 Type Hot-Swap Redundant Power Supply
BPS-270RD/270RDX is a compact (exact PS/2
size) redundant power supply for "Mission
Critical" applications. As "High A v a i l a b i l i t y "
becomes a common requirement, now the
redundant power supply is part of non-stop
computers. With its compact PS/2 size, BPS270RD/RDX can be easily applied to get great
added value of "High Availability" without
changing any mechanism or redesigning
systems.
Specifications
Voltage
Frequency
Current
◆ Input
◆ DC
Max. Load
Min. Load
Max. Watt.
Load Reg.
Cross Reg.
Line Reg.
Ripple
Noise
Output
◆ Efficiency
◆ Holdup
◆ Hi-Pot
Time
Test
◆ Over
Voltage Protection
Current Protection
◆ Over Load Protection
◆ MTBF
◆ Safety Approval
◆ Over
◆ Temperature/Humidity
◆ Dimension
(WxDxH)
AC 90 ~ 132V, 180 ~ 264V selectable
47 ~ 63 Hz
6A@115V, 3A@230V
+5V
+12V +3.3V -5V
-12V
30A
16A
20A
0.5A 0.5A
3A
1A
3A
0A
0A
240W
10W
+/-5% +/-5% +/-5% +/-10% +/-10%
+/-5% +/-5% +/-5% +/-10% +/-10%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-2% +/-2%
> 75% at full load
20ms. at full load
1.5KVRMS, 60sec. from i/p to ground
3.0KVRMS, 60sec. from i/p to o/p
+5V: 5.6V ~ 6.5V/+12V: 12.6V ~1 5.6V
+5V, +12V: 130% ~ 150%
Total o/p 110% ~ 130%
> 176,000hrs
UL, CUL, TUV, CE
Operating : 0 ~ 50˚C, 20 ~ 90%RH
Storage : -20 ~ 60˚C, 5 ~ 95%RH
150x175x86 mm / 5.9"x6.9"x3.4"
Features
The most compact hot-swap redundant PSU with standard
PS/2 size to fit into a limited space
Two 250W hot-swap redundant modules provide 500W output
for the new computers high-frequency CPUs
Provide 1.5A@-12V for CTI systems
High reliable ball bearing sensitive fan
Equipped with 4-ear brackets for fixing the PSU easily and
flexibly
Alarm beeping and LED indicator of defective module for
field replacement directly
Enhanced swappable fan to get high security for 100%
mission critical applications
Support 3.3V and stand-by +5V (1.5A) output ( ATX 2.01)
with a 20-pin ATX connector for ATX /B (BPS-270RDX and
BPS-270RDX-1)
Engineering Drawing
Ordering Guide
●
BPS-270RD
●
BPS-270RDX
●
BPS-270RD-1
●
BPS-270RDX-1
270W PS/2 type redundant PSU
270W PS/2 type ATX output redundant PSU
270W PS/2 type front loading redundant PSU with swappable fan
270W PS/2 type front loading ATX output redundant PSU with
swappable fan
54
PW-380/250
Standard 380W/250W PS/2 Type Power Supply
Specifications
Voltage
AC 95 ~ 132V, 185 ~ 264V selectable
Frequency 47 ~ 63 Hz
10A@115V, 5A@230V for 380W
Current
8A@115V, 4A@230V for 250W
+5V
+12V
-5V
-12V
Max. Load 36A
16A
0.5A
0.5A
◆ DC
380W
Output
Min. Load 3A
1A
0A
0A
Max. Load 25A
10A
0.5A
0.5A
250W
Min. Load 1A
0.4A
0A
0A
◆ Efficiency
> 70%
◆ Hold up time
16ms at full-load
1.5K VRMS, 60 sec from i/p to ground
◆ Hi-Pot Test
1.5K VRMS, 60 sec from i/p to o/p
+5V: 5.6V ~ 6.5V/+3.3V: 3.8V ~ 4.3V
◆ Over Voltage Protection
+12V: 13.6V ~ 15.6V
+5V, +3.3V: 110% ~ 130%
◆ Over Current Protection
+12V: 120% ~ 150%
◆ Over Load Protection
Total o/p 110% ~ 130%
◆ MTBF
> 50,000hrs
◆ Safety Approval
UL, CSA, TUV, CE, CB, FCC
Operating : 0 ~ 50˚C, 20 ~ 90%RH
◆ Temperature/Humidity
Storage : -20 ~ 60˚C, 5 ~ 95%RH
◆ Dimension (WxDxH)
150x140x86 mm / 5.9"x5.5"x3.4"
◆
Input
PW-380/250 is a typical PS/2 power supply that
has been used for several years. With its steady
quality and reliability, it is still extensively adopted
and receives high popularity.
Ordering Guide
●
PW-380
●
PW-380A
●
PW-250
380W PS/2 type AT PSU
380W PS/2 type Auto-range AT PSU
250W PS/2 type AT PSU
PW-300ATX
Standard 300W PS/2 Type Power Supply
Features
Full 300W output design
Provide OVP, OCP, OLP protection
Application
Rack-mount chassis
Factory environment
Specifications
Voltage
AC 85 ~ 132V, 185 ~ 254V selectable
Frequency 47 ~ 63 Hz
Current
10A@115V, 5A@230V for 300W
+5V
+12V +3.3V -5V
-12V
Max. Load 30A
14A
22A
0.8A 1A
◆ DC Output
Min. Load 2A
0.2A 0A
0A
0A
Max. Watt (+5V)+(+3.3V) < 140W
◆ Efficiency
> 70%
◆ Hold up time
16ms at full-load
1.5K VRMS, 60 sec from i/p to ground
◆ Hi-Pot Test
1.5K VRMS, 60 sec from i/p o/p
◆ Over Voltage Protection +5V: 5.6V ~ 6.5V/+3.3V: 3.8V ~ 4.3V
+12V: 13.6V ~ 15.6V
◆ Over Current Protection +5V, +3.3V: 110% ~ 130%
+12V: 120% ~ 150%
◆ Over Load Protection
Total o/p 110% ~ 130%
◆ MTBF
> 40,000hrs
◆ Safety Approval
UL, CSA, TUV, CE, CB, FCC
Operating : 0 ~ 50˚C, 20 ~ 90%RH
◆ Temperature/Humidity
Storage : -20 ~ 60˚C, 5 ~ 95%RH
◆ Dimension (WxDxH)
150x140x86 mm / 5.9"x5.5"x3.4"
◆
Because of its good reliability and quality for ATX
functionality. PW-300ATX is the best seller among
all PSUs.
Ordering Guide
●
PW-300ATX
300W PS/2 type ATX PSU
Input
62
ORION-300DX
-48V & 24V DC Input PS/2 Type DC/DC Converter with ATX Output
Specifications
Voltage
◆
Input
Current
◆
DC Output
Max. Load
Min. Load
Max. Watt.
Load Reg.
Cross Reg.
Line Reg.
Ripple
Noise
Efficiency
Over Voltage Protection
◆ Over Load Protection
◆ MTBF
◆
◆
◆
Temperature/Humidity
Safety Approval
◆ Dimension (WxDxH)
◆
DC -40V ~ -72V for -48V input
DC 19V ~ 32V for 24V input
10A@-48V DC input
20A@24V DC input
+5V
+3.3V +12V -5V
-12V
30A
15A
15A
2A
2A
2A
0A
0.1A 0A
0A
150W
180W 10W 24W
+/-3% +/-2% +/-5% +/-2% +/-2%
+/-5% +/-5% +/-5% +/-10% +/-10%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-2% +/-2%
> 65%
+5V: 5.6V ~ 6.5V
Total o/p 110% ~ 130%
> 150,000 hrs
0 ~ 70˚C (-20˚C can start up)
The maximum 300W output power
should be under the cabinet
temperature 30˚C
TUV, CSA, NRTL/C, UL
150x140x86 mm / 5.9"x5.5"x3.4"
Features
-48 or +24 V DC input, ATX output
Provide 1.2A for stand-by +5V
Provide +5V o/p to have OVP design
-20˚C can start up
Application
Truck
Telecommunication
Remote control unit
Ordering Guide
●
ORION-300DX/48
●
ORION-300DX/24
300W PS/2 type -48V DC/DC converter with ATX output
300W PS/2 type 24V DC/DC converter with ATX output
BPS-250RDDX/48
-48V Input 450W PS/2 Type DC/DC Hot-Swap Redundant Power Supply
Specifications
◆
Features
AT or ATX output as optional
Provide OVP, OLP protection
Provide 1A for +5V VSB
Application
Telecommunication
environment
Remote control unit
Input
◆
DC Output
◆
◆
Efficiency
Holdup Time
◆
Hi-Pot Test
Voltage
Current
Max. Load
Min. Load
Max. Watt.
Load Reg.
Cross Reg.
Line Reg.
Ripple
Noise
Over Voltage Protection
Over Load Protection
◆ MTBF
◆ Safety Approval
◆
◆
Ordering Guide
●
BPS-250RDD/48
-48V DC input PS/2 type hot-swap redundant PSU
●
BPS-250RDDX/48
-48V DC input PS/2 type hot-swap ATX redundant PSU
◆
Temperature/Humidity
◆
Dimension (WxDxH)
DC -40 to -56V
8A
+5V
+3.3V +12V -5V
-12V
30A
15A
14A
0.5A
0.5A
3A
3A
1A
0A
0A
220W
10W
+/-5% +/-5% +/-5% +/-10% +/-10%
+/-5% +/-5% +/-5% +/-10% +/-10%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-2% +/-2%
> 75% at full load
16ms. at full load
1.5KVRMS, 60sec. from i/p to ground
3.0KVRMS, 60sec. from i/p to o/p
+5V: 5.6V ~ 6.5V/+12V: 12.6V ~ 15.6V
Total o/p 130% ~ 150%
> 167,000 hrs
UL, CUL, TUV, CE
Operating : 10 ~ 50˚C, 20 ~ 90%RH
Storage : -20 ~ 60˚C, 5 ~ 95%RH
150x140x86 mm / 5.9"x5.5"x3.4" (RDD)
150x175x86 mm / 5.9"x6.9"x3.4" (RDDX)
60
PW-330ATXE-12V
330W PS/2 Power Supply for Pentium 4 Processor Solution
PW-330ATXE-12V is the up-to-date power supply
that meets the new power consumption demand on
Pentium 4 processor. It's a standard PS/2 power
supply with full 330W ATX (Ver. 2.03) output for
server and industrial application, the most economical
for Pentium 4 processor based system. Want to
upgrade your M/B to Pentium 4 processor solution?
Try PW-330ATXE-12V, you will see the difference.
Specifications
Features
Support Intel Pentium 4 processor
Optional Auto range function
Dual-ball bearing fan
OVP on 3.3V/5V/12V
Optional over Temp. protection
2-year warranty
◆
Input
Voltage
Frequency
Current
◆
DC Output
Max. Load
Min. Load
Max. Watt.
Efficiency
Holdup Time
◆ Hi-Pot Test
◆
Application
PC server
Industrial computer
◆
Over Voltage Protection
Over Circuit Protection
◆Over Load Protection
◆ MTBF
◆
◆
◆
Temperature/Humidity
◆
Safety Approval
Dimension (WxDxH)
◆
95~132/190~264V AC, switch selectable
47~63 Hz
Max. 10A/90V AC, 5A/230V AC
+5V
+12V
-5V
-12V
+5VSB
+3.3V
30A
16A
0.3A
0.8A
2A
28A
0.1A
0A
0A
0A
0.1A
0.3A
+5V/+3.3V max. 200W, total max. output 350W
> 68% at full load
16.7 ms minimum with full load
1500VRMS, 50Hz, 1 min., from input to ground.
3000VRMS, 50Hz, 1 min., from input to outputs.
+5V: 5.6V~6.5V, +3.3V: 4V~4.5V, +12V: 13.5V~15.5V
Shut Down Power Supply
Total 5V/3.3V/12V combined output 105% - 160%
> 100,000hrs
Operating: +0 ~ +40˚C, 10%~90% non-condensing
Storage: -40 ~ +70˚C, 5% ~ 95% non-condensing
UL / TUV / FCC / CE / CB
150 x 86 x 140 mm, standard PS/2
Ordering Guide
●
PW-330ATXE-12V
PS/2 330W power supply for Pentium 4 processor
Portwell, Inc.
American Portwell Technology, Inc.
Portwell Japan, Inc.
3F, No. 92, Nei-Hu Rd., Sec.1
114 Taipei, Taiwan, R.O.C.
Te l : +886-2-2799-2020
Fax: +886-2-2799-1010
E-amil: [email protected]
http://www.portwell.com.tw
38507 Cherry St., Suite D
Newark, CA 94560 USA
Te l : (510)790-9192
Fax: (510)790-9191
E-mail: [email protected]
http://www.portwell.com
101-0042 Ueda Build. 7F, 10-2 Kanda higashi
matsushita-cho chiyoda-ku Tokyo Japan
Te l : +81-3-5298-8071
Fax: +81-3-5298-8072
E-mail: [email protected]
http://www.portwell.co.jp
ORION-450AX
Full 450W Single PS/2 Type ATX Power Supply with Auto-range Input
Specifications
◆
◆
Voltage
Frequency
Current
Input
DC Output
Max. Load
Min. Load
Max. Watt.
Load Reg.
Cross Reg.
Line Reg.
Ripple
Noise
◆
Efficiency
Holdup Time
◆
Hi-Pot Test
◆
Over Voltage Protection
◆
Over Circuit Protection
Over Load Protection
◆ MTBF
◆ Safety Approval
◆
◆
◆
Temperature/Humidity
◆
Dimension (WxDxH)
AC 95 ~ 132V, 185 ~ 264V Auto-range
47 ~63 Hz
7A@115V, 4A@230V
+5V
+3.3V +12V -5V
-12V
40A
28A
17A
0.5A 1.5A
2A
0A
0.2A 0A
0A
225W
204W 2.5W 18W
+/-5% +/-5% +/-5% +/-5% +/-10%
+/-5% +/-5% +/-5% +/-10% +/-5%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-1% +/-1%
+/-1% +/-1% +/-1% +/-2% +/-2%
> 70% at full load
16.7ms. at full load
1.5KVRMS, 60sec. from i/p to ground
3.0KVRMS, 60sec. from i/p to o/p
+5V: 5.6V ~ 6.5V/+3.3V: 4.0V ~ 4.5V
+12V: 13.5V ~ 15.5V
Shutdown power supply
Total o/p 110% ~ 130%
> 100,000hrs
UL, CSA, TUV, CE, FCC
Operating : 0 ~ 50˚C, 20 ~ 90%RH
Storage : -20 ~ 60˚C, 5 ~ 95%RH
150x140x86 mm / 5.9"x5.5"x3.4"
ORION-450AX is a brand new design for higher
output ATX PSU. It is designed to meet the
demand of high current support, such as servers
or disk-array.
Features
Application
Full 450W output design
Auto-range AC input
+5V,+12V,+3.3V OVP design
One ATX and one P9 connector
Internet server
High-end Rack-mount
computer
Ordering Guide
●
ORION-450AX
Full 450W PS/2 type ATX PSU with Auto-range input
ORION-330A
Full 330W Single PS/2 Type AT Power Supply with Auto-range Input
Specifications
◆
ORION-330A is the most cost effective PSU
designed to fit your mid-grade server that needs
more power than that of PC. It is mostly adopted in
the rack-mount systems.
Features
Full 330W output design
Auto-range AC input
Provide OVP, OCP protection
Application
Rack-mount chassis
Factory environment
Ordering Guide
●
61
ORION-330A
Full 330W PS/2 type AT PSU with Auto-range input
Input
Voltage
Frequency
Current
Max. Load
Min. Load
Max. Watt.
Load Reg.
Cross Reg.
Line Reg.
Ripple
Noise
◆
DC Output
◆
◆
Efficiency
Holdup Time
◆
Hi-Pot Test
◆
Over Voltage Protection
Over Circuit Protection
Over Load Protection
◆ MTBF
◆ Safety Approval
◆
◆
◆
Temperature/Humidity
◆
Dimension (WxDxH)
AC 95 ~ 132V,190 ~ 264V Auto-range
47 ~ 63 Hz
10A@115V, 5A@230V
+5V
+12V
-5V
-12V
30A
14A
0.5A
1A
2A
0.2A
0A
0A
150W
168W
2.5W
12W
+/-5%
+/-5%
+/-5%
+/-10%
+/-5%
+/-5%
+/-10% +/-5%
+/-1%
+/-1%
+/-1%
+/-1%
+/-1%
+/-1%
+/-1%
+/-1%
+/-1%
+/-1%
+/-2%
+/-2%
> 70% at full load
16.7ms. at full load
1.5KVRMS, 60sec. from i/p to ground
3.0KVRMS, 60sec. from i/p to o/p
+5V: 5.6V ~ 6.5V/+3.3V: 4.0V ~ 4.5V
+12V: 13.5V ~ 15.5V
Shutdown power supply
Total o/p 110% ~ 130%
> 100,000 hrs
UL, CSA, TUV, CE, FCC
Operating : 0 ~ 50˚C, 20 ~ 90%RH
Storage : -20 ~ 60˚C, 5 ~ 95%RH
150x140x86 mm / 5.9"x5.5"x3.4"
ORION-3001PY
Full 300W PS/2 type Active PFC Power Supply
ORION-3001PY is the most up-to-date
Power Supply to meet different system demands.
It's a standard PSII type power supply with ATX
(Ver. 2.03) output and active PFC design to meet
the environmental protection needs. Its very
reliable design makes it not only fit normal
computing system requests, but also meet certain
critical applications.
Specifications
Features
Support Intel Pentium 4 processor
Support AMD Athlon processor
Support special input frequency (400Hz)
Active PFC design
Full range AC input
Full 300W output design
Maximum output power 180W on +3.3V
and +5V
◆
Input
Voltage
Frequency
Current
◆
DC Output
Max. Load
Min. Load
Max. Watt.
Efficiency
Holdup Time
◆ Hi-Pot Test
◆
◆
Application
High-end rack-mount system
Industrial computer
Factory environment
Over Voltage Protection
Over Circuit Protection
◆Over Load Protection
◆ MTBF
◆
◆
◆
Temperature/Humidity
◆
Safety Approval
Dimension (WxDxH)
◆
100~240 VAC +/- 10%, Full Range
47~63 Hz, 400Hz
7A/90~132V , 4A/180~264V
+5V
+12V
-5V
-12V
+5VSB
+3.3V
30A
15A
0.3A
0.8A
2A
28A
0.1A
0A
0A
0A
0A
0.3A
(+5V) + (+3.3V) = 180W
> 65% at full load
16ms minimum with full load
1500VRMS, 50Hz, 1 min., from input to ground.
3000VRMS, 50Hz, 1 min., from input to outputs.
+5V: 5.5V~7.0V, +3.3V: 3.5V~4.5V, +12V: 12.7V~15.6V
Shut Down Power Supply
Total Output 120% - 140%
> 100,000hrs
Operating: +10 ~ +50˚C, 20% ~ 80% RH
Storage: -40 ~+70˚C, 10% ~ 95% RH
UL / TUV / CSA / CE / Nemko
150x140x86mm , standard PS/2 size
Ordering Guide
●
ORION-3001PY
Full 300W PS/2 type Active PFC Power Supply
Portwell, Inc.
American Portwell Technology, Inc.
Portwell Japan, Inc.
3F, No. 92, Nei-Hu Rd., Sec.1
114 Taipei, Taiwan, R.O.C.
Te l : +886-2-2799-2020
Fax: +886-2-2799-1010
E-amil: [email protected]
http://www.portwell.com.tw
38507 Cherry St., Suite D
Newark, CA 94560 USA
Te l : (510)790-9192
Fax: (510)790-9191
E-mail: [email protected]
http://www.portwell.com
101-0042 Ueda Build. 7F, 10-2 Kanda higashi
matsushita-cho chiyoda-ku Tokyo Japan
Te l : +81-3-5298-8071
Fax: +81-3-5298-8072
E-mail: [email protected]
http://www.portwell.co.jp
ORION-400S
Slim Type of 400W ATX Power Supply
Specifications
Voltage
AC 90 ~ 132V, 180 ~ 264V selectable
Frequency 47 ~ 63 Hz
Current
10A@115V, 6A@230V
+5V
+12V
+3.3V -12V
-5V
◆ DC Output
Max. Load
40A
16A
20A
1A
0.5A
Min. Load
3A
1A
0A
0A
0A
◆ Efficiency
>70%
◆ Hold up Time
20ms. at full load
1.5K VRMS, 60sec. from i/p to ground
◆ Hi-Pot Test
3.0K VRMS, 60sec. from i/p to o/p
◆ Over Voltage Protection +3V: 3.7 ~ 4.5V; +5V: 5.6 ~ 6.9V
+12V: 13.6 ~ 15.6V
◆ Over Load Protection
When over 120%
◆ MTBF
> 100,000hrs
Operating : 10 ~ 50˚C
Non-operating : -20 ~ 60˚C
◆ Temperature/Humidity
Humidity: 20~90% non-condensing at 40˚C
5~95% non-condensing at 50˚C
◆ Safety Approval
UL, TUV, CB
◆ Dimension (WxDxH)
100x190x70 mm / 3.94"x7.48"x2.76"
◆
ORION-400S is the smallest 400W ATX
power supply for 2U system in the world.
Its fancy and smart design makes it
possible to integrate those compact
systems into your applications. To meet
the new power consumption demand from
the latest Pentium ® 4 processor, 12V
output is also upgraded.
Features
Applications
Support Pentium 4 processor
High power output for 2U solution
Total power of +5V &+3.3V is 250W
Provide OVP, OLP, SCP protection
2U rack-mount PC sever
system
Compact node chassis
Input
Ordering Guide
●
ORION-400S
400W slim ATX PSU for 2U Chassis with 12V output connector for
Pentium ® 4 processor
Portwell, Inc.
American Portwell Technology, Inc.
Portwell Japan, Inc.
3F, No. 92, Nei-Hu Rd., Sec.1
114 Taipei, Taiwan, R.O.C.
Te l: +886-2-2799-2020
Fax: +886-2-2799-1010
E-amil: [email protected]
http://www.portwell.com.tw
38507 Cherry St., Suite D
Newark, CA 94560 USA
Te l: (510)790-9192
Fax: (510)790-9191
E-mail: [email protected]
http://www.portwell.com
101-0042 Ueda Build. 7F, 10-2 Kanda higashi
matsushita-cho chiyoda-ku Tokyo Japan
Te l: +81-3-5298-8071
Fax: +81-3-5298-8072
E-mail: [email protected]
http://www.portwell.co.jp
* Specifications are subject to change without notice.
* Pentium 4 is a registered trademark of Intel Corporation.
* Other trademarks, logos, brand names and company names are the
property of their respective owners.
ORION-250S
Slim Type of 250W ATX Power Supply
Specifications
Voltage
AC 90 ~ 132V, 180 ~ 264V selectable
Frequency 47 ~ 63 Hz
Current
6A@115V, 3A@230V
+5V
+12V +3.3V -12V -5V
◆ DC Output
Max. Load 30A
10A
15A
0.5A
0.5A
Min. Load 3A
1A
1A
0A
0A
◆ Efficiency
>75%
◆ Hold up Time
16ms. at full load
1.5K VRMS, 60sec. from i/p to ground
◆ Hi-Pot Test
3.0K VRMS, 60sec. from i/p to o/p
◆ Over Voltage Protection +5V: 5.15V ~ 6.45V/+12V: 12.6V ~ 15.6V
◆ Over Load Protection
When over 120%
Operating : 10 ~ 50˚C
◆ Temperature/Humidity
Storage : -20 ~ 60˚C
◆ Safety Approval
UL, TUV, CE, FCC
◆ Dimension (WxDxH)
100x190x40.5 mm / 3.94"x7.5"x1.6"
◆
Input
ORION-250S is a high output PSU for 1U
chassis. It's the best choice for your compact
system applications.
Features
Ordering Guide
●
ORION-250S
250W slim ATX PSU for 1U Chassis
40.5mm high, the best solution
250W high output for 1U solution
Total power of +5V &+3.3V is 150W
Provide OVP, OLP, SCP protection
Application
1U chassis
Compact node chassis
ORION-300S
Slim Type of 300W ATX Power Supply
Specifications
Voltage
AC 90 ~ 132V, 180 ~ 264V selectable
Frequency 47 ~ 63 Hz
Current
4A@115V, 2A@230V
+5V
+12V +3.3V -12V
-5V
◆ DC Output
Max. Load 30A
14A
15A
1A
0.5A
Min. Load 3A
1A
1A
0A
0A
◆ Efficiency
>75%
◆ Hold up Time
16ms. at full load
1.5K VRMS, 60sec. from i/p to ground
◆ Hi-Pot Test
3.0K VRMS, 60sec. from i/p to o/p
◆ Over Voltage Protection +5V: 5.15V ~ 6.45V/+12V: 12.6V ~ 15.6V
◆ Over Load Protection
When over 120%
Operating : 10 ~ 50˚C
◆ Temperature/Humidity
Storage : -20 ~ 60˚C
◆ Safety Approval
UL, TUV, CE, FCC
◆ Dimension (WxDxH)
100x210x70 mm / 3.94"x8.3"x2.8"
◆
Input
ORION-300S is the smallest 300W ATX PSU
in the world. Its fancy and smart design makes
it possible to integrate those compact systems
into your applications.
Features
Ordering Guide
●
ORION-300S
300W slim ATX PSU for 2U Chassis
59
High power output for 2U solution
Total power of +5V &+3.3V is 150W
Provide OVP, OLP, SCP protection
Application
2U chassis
Compact node chassis
ORION-150AX
Slim Type of 150W ATX Power Supply
Specifications
Voltage
AC 90 ~135V, 180 ~260V Auto-range
Frequency 47 ~ 63 Hz
Current
5A@115V, 2.5A@230V
+5V
+12V +3.3V -12V
-5V
◆ DC Output
Max. Load 10A
6A
6A
1A
0.2A
Min. Load 1A
1A
1A
0A
0A
◆ Efficiency
> 60%
◆ Hold up Time
16ms. at full load
1.5K VRMS, 60sec. from i/p to ground
◆ Hi-Pot Test
3.0K VRMS, 60sec. from i/p to o/p
◆ Over Voltage Protection +5V: 5.5V ~ 7V/+3.3V: 4.0V ~ 4.5V
+12V: 13.5V ~ 16V
◆ Over Load Protection
110% ~150%
Operating : 10 ~ 50˚C
◆ Temperature/Humidity
Storage : -20 ~ 60˚C
◆ Safety Approval
UL, TUV, CE, FCC
◆ Dimension (WxDxH)
100x190x40.5 mm / 3.94"x7.5"x1.6"
◆
Input
ORION-150AX is the smallest 150W AT X
PSU in the world. Its fancy and smart design
makes those compact systems available in
your applications.
Features
Ordering Guide
●
ORION-150AX
Slim type of 150W ATX PSU with Auto-range input
40.5mm high, the best solution
95~135V, 180~265 Auto-range input
PFC function as optional
Provide OVP, OLP, SCP protection
Application
1U chassis
Compact node chassis
ORION-48T
-48V DC Output Power Supply Tester
ORION-48T is designed for those engineers who
need 48V power source for system testing. By
using so many batteries to get the 48V power
source in our laboratory is not easy. The ORION48T is just what engineers need for their
application.
Ordering Guide
●
ORION-48T
-48V DC power supply tester
Features
Input voltages: 110V/220V
Output voltage: -48V DC
Max. output: 300W
Application
Testing equipment
64
BPS-7004/24/12
70W Open Frame +24V or +12V DC to DC Power Supply
Specifications
◆
Voltage
Input
Current
◆
Max. Load
Min. Load
Load Reg.
Cross Reg.
Line Reg.
Ripple
Noise
DC Output
◆
Efficiency
Holdup Time
◆
Hi-Pot Test
◆
Over Voltage Protection
Over Load Protection
◆ MTBF
◆ Safety Approval
◆
◆
◆
Temperature/Humidity
◆
Dimension (WxDxH)
DC 18V to 30V for 24V input
DC 10V to 18V for 12V input
4A
+5V
+12V
-5V
-12V
7A
2.5A
0.3A
0.3A
3A
1A
0A
0A
+/-5%
+/-5%
+/-10% +/-10%
+/-5%
+/-5%
+/-10% +/-10%
+/-1%
+/-1%
+/-1%
+/-1%
+/-1%
+/-1%
+/-1%
+/-1%
+/-1%
+/-1%
+/-2%
+/-2%
> 70% at full load
16ms. at full load
1.5KVRMS, 60sec. from i/p to ground
3.0KVRMS, 60sec. from i/p to o/p
+5V: 5.15V ~ 6.45V/+12V: 12.6V ~ 15.6V
Total o/p 130% ~ 150%
> 50,000hrs
UL, CUL, TUV, CE
Operating : 10 ~ 50˚C, 20 ~ 90%RH
Storage : -20 ~ 60˚C, 5 ~ 95%RH
80.6x127x50 mm / 3.2"x5"x2"
BPS-7004 is a well designed PC PSU for those
applications to equipment for boat, mobile and
truck. Without the possibility of fan failure, it is
more stable and reliable than any others.
Features
Max. output 70W
Open frame design to save space
Provide OVP, OLP protection
Application
Compact chassis
Equipment
Panel PC
Ordering Guide
●
BPS-7004/24
●
BPS-7004/12
70W open frame 24V DC/DC converter
70W open frame 12V DC/DC converter
SNP-9F40
65W Universal Input Open Frame Power Module
Specifications
SNP-9F40 is an open frame PSU used in those
compact machine or equipment. It has been in
the market for a long time because of its good
reliability and quality.
◆
Input
◆
DC Output
◆
◆
Efficiency
Holdup Time
◆
Hi-Pot Test
Voltage
Frequency
Current
Max. Load
Min. Load
Max. Watt.
Over Voltage Protection
Over Circuit Protection
◆ Over Load Protection
◆ MTBF
◆
◆
Features
Universal AC input
Easy to install
Long life cycle
Application
Compact chassis
Equipment
Panel PC
◆
Temperature/Humidity
◆
Safety Approval
Dimension (WxDxH)
◆
Ordering Guide
63
●
SNP-9F40
65W universal input power supply
AC 90 ~ 264V
47 ~ 63 Hz
1.5A@115V, 0.8A@230V
+5V
+12V
-5V
-12V
4A
3A
0.3A
0.3A
0A
0A
0A
0A
20W
36W
1.5W
3.6W
>70%
16ms. at full load
1.5KVRMS, 60sec. from i/p to ground
3.0KVRMS, 60sec. from i/p to o/p
Crowbar, Trip point 6.2V +/-0.5V
Auto recover
Fold back
281,000hrs
Operating : 0 ~ 50˚C, 20 ~ 90%RH
Storage : -20 ~ 60˚C, 5 ~ 95%RH
TUV, CSA, NRTL/C
127x76.2x36 mm / 5"x3"x1.4"
ORION-150AX
Slim Type of 150W AT Power Supply
Specifications
Voltage
AC 95 ~135V, 180 ~265VAC auto range
Frequency 47 ~63 Hz
Current
40A@115V, 2A@230V
+5V
+12V
-12V
-5V
◆ DC Output
Max. Load 10A
6A
1A
0.1A
Min. Load 1A
0.2A
0A
0A
◆ Efficiency
>60%
◆ Hold up Time
16ms. at full load
1.5K VRMS, 60sec. from i/p to ground
◆ Hi-Pot Test
3.0K VRMS, 60sec. from i/p to o/p
◆ Over Voltage Protection +5V-5.5V ~7V, 3.3V-4.0V ~4.5V
◆ Over Load Protection
110% ~150%
◆ Short Circuit Protection
+5V, -5V, +12V, -12V
Operating : 10 ~50˚C
◆ Temperature/Humidity
Storage : -20 ~60˚C
◆ Safety Approval
UL, TUV
◆ Dimension (WxDxH)
100x190x40.5 mm / 3.94"x7.5"x1.6"
◆
Input
ORION-150AX is the smallest 150W AT X
PSU in the world. Its fancy and smart design
makes those compact systems available in
your applications
Features
●
ORION-150AX
●
ORION-150A
Application
40.5mm height, best solution
95~135V, 180~265 auto range input
PFC function as optional
Provide OVP OLP SCP protection
Ordering Guide
150W slim ATX PSU with auto range input
1U height Chassis
Compact node chassis
150W slim AT PSU with auto range input
CABLE-ATX-P8P9
CABLE-EXT-AT
CABLE-EXT-ATX
Cable for ATX to P8/P9
connectors converting
Extension Cable for P8/P9
connectors
Extension Cable for ATX to
ATX+P8/P9 connectors
C A B L E - ATX-P8P9
is an
extension cable to convert the
ATX connector to P8P9
connectors for fitting those old
backplane or computer boards.
With an extra power on/off
cable, it is easy for user to
control their system.
CABLE-EXT-AT is a Y cable to
extend one set of P8/P9
connectors into two. This is
important for those backplanes
with dual power-in connectors.
Features
ATX convert to P8P9 connector
2 pins of PSU on-off
Features
Y cable of P8P9 connector
Ordering Guide
●
CABLE-ATX-P8P9
Cable for ATX to P8/P9 connectors
converting
CABLE-EXT-ATX is a special Y
cable that extends the A T X
connector to ATX and P8/P9
connectors. It is well-adopted in
those high-end systems that
need both types of ATX and
P8/P9 connectors altogether.
Features
Y cable of ATX connector
Ordering Guide
●
CABLE-EXT-AT
Extension cable for P8/P9 connectors
Ordering Guide
●
CABLE-EXT-ATX
Extension cable for ATX to ATX+P8/P9
connectors
66
P4 power adapter cable *_*
•
General Information
–
•
Features
–
•
CABLE-HDD-P4 is a adapter cable which was made for the power supply does not
support +12V power connector by convert two peripheral power connectors
Solve the connection problem between power supply and P4 SBC
Ordering Guide – CABLE-HDD-P4
–
Adapter cable for two peripheral (hard drive type) power connectors to one +12V (4-pin)
power connector Ordering Guide
Item # B7861130
Internal Use Only
Do Not Copy
Portwell Confidential
6
Leading The Evolution
Rack-mount Server
ACTI-8500
ACTI-3500
ACTI-2800
ACTI-1500
ACTI-1234
19" 5U Rack-mount CTI Server
The World's First 2U SCSI-to-IDE RAID Server with 6 IDE Drives
2U Fault Resilient Server with Hot-Swappable Power Supply
1U Server with Hot-Swappable, H/W Based Mirroring RAID
Compact and Economical 1U Rack-mount Server
RAID Subsystem
CETUS-3400
CETUS-3300
CETUS-3200
The Most Cost-effective 3U SCSI-to-IDE RAID Subsystem
19" 3U Advanced SCSI-to-SCSI RAID Subsystem
2U Cost Effective SCSI-to-IDE RAID Subsystem
19" Rack-mount 5U CTI Server
Anti-vibration
Height-adjustable card retainer
ensures 100% bus contact
Adaptability
Rich choice of SBCs and backplanes to
meet your different requirements
Max. Data Storage Capacity
Eight 5.25" drive space could
install up to twelve mobile racks
for 3.5" HDDs
Reliability
3+1 load-balance hot-swap
redundant PSU with max. 800W
output for system availability
and durability
Security
System switch with cap protection
Customization
Changeable system front panel
for easier customization
Feature at a Glance Feature at a Glance
Advanced fault-resilient features for non-stop
computing
Easy Maintenance with hot-swap HDDs, PSU,
and cooling fans
More safety design for better system security
Flexible design for easier customization
Flexibility
Optional slim type
CD-ROM & FDD
Serviceability
Specifications
Intel®
Specifications
Pentium® III processor 850MHz or above
CPU
Single or dual
Memory
128MB SDRAM or above
Chipset
Intel® 82440BX
Display
C&T 69000 AGP VGA
LAN
Intel® 82559 10/100 BaseT Ethernet
Expansion Slot
Twelve PCI and six ISA slots
Drive Bay
Eight 5.25" and one 3.5" FDD
Power Supply
600W+200W N+1 redundant PSU w/ enhanced -12VDC output,
60A@+5v, 24A@+12V, 3A@-12V, 1.5A@-5V
Cooling Fan
Three 12cm 86.5 cmf hot-swap and dual ball-bearing fans
Operating Temperature 0˚C to 55˚C, 20~90% RH
Storage Temperature
-20˚C to 70˚C, 5~95% RH
Dimension
482(W) x 673(D) x 220(H)mm/19" x 26.5" x 8.7"
Weight (w/o HDD)
Gross:25kg / 52.5lb / Net:27kg / 56.7 lb
Detachable card
cage for easier field
service and system
installation
Safty
Two positions for
card retainer to fix
the add-on cards
more tightly
Superior Cooling
Three 12 com toolfree hot-swap
cooling fans with
the best ventilation
for long system life
Update Date :2001.10.15
1U Server with Hot-swappable, H/W Based Mirroring RAID
Features
A total of 42 sets of ACTI-1500 installed
in a 42U cabinet for colocation
Cost effective IDE RAID level 1 solution
Built-in OS independent Hardware-based
IDE mirror RAID controller
Specifications
Automatic on-line rebuilding to secure the
precious data
CPU
Drive Bay
Support single and dual Intel® FC-PGA
Pentium III or Celeron™ peocessor
Two IDE Hot-swap mobile racks and one
removable slim-type CD-ROM/FDD module
Hot-swappable mobile racks for easy
maintenance HDD
LAN
Data Transfer Rate
Support single & dual 10/100 Mbps LAN ports
Disk interface Ultra DMA 66
Audible alarm for drive failure warning
Memory
Operating Temperature Range
Support two and four DIMMs SDRAM, up to
2GB, depends on mother board used
5 to 40˚ C, 20-90%RH
Power Supply
0 to 70˚ C, 5-95%RH
Storage Temperature Range
250W ATX power supply
Dimension
Cooling Fan
483(W) x 580(L) x 44.5(H) mm
19"(W) x 22.8"(L) x 1.75"(H)
One 10cm blower with two 4cm ball-bearing
fans
RAID Levels
Support Hardware management
(voltage; CPU thermal; fan)
Support various mother board
Weight
Gross: 11kg /24.2lb (without HDD)
Net: 8.5kg /18.7lb (without HDD)
0, 1
Color
Zinc-plated
ACTI-2800
2U Fault Resilient Server with Hot-swappable Power Supply
Features
A total of 21 sets of ACTI-2800 installed
in a 42U cabinet for colocation
SCA backplane (Ultra 2)
Heavy duty 230W redundant power
supply to provide secure and sufficient
power source
Specifications
CPU
Operating Temperature Range
Easily detachable top chassis-cover
with thumb screws
Support single and dual Intel® FC-PGA
Pentium III or Celeron™ processor
5 to 40˚ C, 20-90%RH
Detachable CD-ROM and FDD bracket
SCA HDD Backplane
0 to 70˚ C, 5-95%RH
Removable HDD trays with thumb
screws
Storage Temperature Range
Four SCA SCSI HDD connected to a SCA B/P
Dimension
Hard Disk Drive
483(W) x 606(L) x 89(H) mm
19"(W) x 23.9"(L) x 3.5"(H)
Four Hot-swappable SCSI mobile racks
Foldable HDD tray handle
Drive Bay
Weight
Easily detachable fan bracket
One 5.25" drive for CD-ROM or PW-RAID
controller and one 3.5" drive for a standard FDD
Membrane key pad
Power Supply
Gross: 17.8kg /39.2lb
Net: 12.5kg /27.5lb
(without RAID controller and HDD)
Support either CD-ROM or PW-RAID
controller
230W ATX redundant power supply
Color
Riser Card
Black
One and two PCI expansion slots available
depends on mother board used
COMMUNICATION APPLIANCE
ACTI-1500
ACTI-1234
Compact and Ecomical 1U Rack-mount Server
Features
◆
A total of 42 sets of ACTI-1234 installed
in a 42U cabinet for colocation
◆
Support various mother board
◆
Support single and dual 10/100 Mbps
LAN controller
◆
Two 5.25" HDD, one NB CD-ROM and
one 3.5" FDD
◆
CD-ROM and FDD drive bay can be
converted for HDD use
◆
HDD, LAN and power LED indicators
◆
250W power supply to provide sufficient
power source
◆
Support Hardware management
(voltage; CPU thermal; fan)
Specifications
◆
CPU
◆
Intel®
Support single and dual
FC-PGA
Pentium III or Celeron™ peocessor
◆
◆
2 x HDD + 1 x slim CD-ROM + 1 x 3.5" FDD
◆
Cooling Fan
One 10cm blower with two 4cm ball-bearing
fans
◆
Memory
◆
Expansion Slot
◆
Data Transfer Rate
Disk interface Ultra DMA 66
Dimension
483(W) x 580(L) x 44.5(H) mm
19"(W) x 22.8"(L) x 1.75"(H)
◆
Weight
Gross: 11kg /24.2lb (without HDD)
Net: 8.5kg /18.7lb (without HDD)
Power Supply
250W ATX power supply
Storage Temperature Range
0 to 70°C, 5-95%RH
One PCI slot available
◆
Operating Temperature Range
5 to 40°C, 20-90%RH
Support two/four DIMMs SDRAM, up to 2GB
depends on mother board used
◆
Drive Bay
◆
Color
Zinc-plated
ACTI-3500
The World's First 2U SCSI-to-IDE RAID Server with 6 IDE Drives
Features
The world's first cost-saving 2U RAID server
OS independent and no driver required
Space saving system with up to 6 Ultra DMA
IDE disks
Specifications
Intel® i960 Hardware-based RAID controller
Computing Board
Cooling Fan
Support various SBC boards
Four 8cm ball-bearing fans (4x35.31CFM)
Ultra-wide SCSI host interface
RAID Levels
Operating Temperature Range
0 to 45˚ C, 20-90%RH
Storage Temperature Range
0 to 70˚ C, 5-95%RH
Dimension
On-line Hot-spare and Hot-swap features
and auto-rebuild
483(W) x 638(D) x 89(H) mm
19"(W) x 25.1"(D) x 3.5"(H)
300W redundant power supply provides
secure and sufficient power for system
0, 1, 3, 5, 0+1
Data Transfer Rate
High speed host interface up to 40MB/sec
Hot-swappable mobile racks
For up to 6 IDEs
Peripherals
Support one Laptop type CD-ROM & FDD
Weight
Backplane:
Support 4 PCI slots
Gross: 20kg / 44lb
Net: 12.3kg / 27lb (without SBC & HDD)
Power Supply
Color
Two 300W redundant modules with
load-sharing feature
Black
Fax and pager event notification
Lower cost per megabyte
PICMG backplane for SBC and add-on card
expansion
Compact EZDRV with laptop type of
CD-ROM and FDD
CETUS-3200
2U Cost Effective SCSI-to-IDE RAID Subsystem
Features
The world's first cost-saving 2U RAID
Space saving system with up to 6 ATA 33/66
IDE disks
Optional dual host support
OS independent and no driver require
Intel®
Specifications
i960 Hardware-based RAID controller
Ultra-Wide SCSI host interface
RAID Levels
Operating Temperature Range
0, 1, 3, 5, 0+1
0 to 45˚ C, 20-90%RH
On-line hot spare and swappable features
and auto-rebuild
Data Transfer Rate
Storage Temperature Range
High speed host interface up to 40MB/sec
0 to 70˚ C, 5-95%RH
FAX and pager event notification
Hot-swappable mobile racks
Dimension
For up to 6 IDE HDDs
483(W) x 457(L) x 89(H) mm
19"(W) x 17.9"(L) x 3.5"(H)
Lower cost per megabyte
Memory Cache
Backplane disk channels, no disks cabling
required
16-128MB (built-in 32MB)
Weight
Power Supply
Gross: 18kg / 39.6lb (without HDD)
Net: 12kg / 26.45lb (without HDD)
300W redundant power supply provides
secure and sufficient power for system
Two 300W redundant modules with
load-sharing feature
Cooling Fan
Four 8cm ball-bearing fans (4x35.31CFM)
Color
Black
19" 3U Advanced SCSI-to-SCSI RAID Subsystem
Features
Fully integrated system backplane, allows
cable-less connection to all HDDs for better
performance and reliability
Two Hot-swappable fans, located at the back
for easy maintenance
Specifications
Front-side-loading Hot-swappable redundant
power supply
RAID Controller
Operating Temperature Range
Equipped with Intel® i960 chipset based,
Ultra2 SCSI - Ultra2 SCSI RAID controller
5 to 45˚C, 20-90%RH
Hard Disk Drive Bay
0 to 70˚C, 5-95%RH
Storage Temperature Range
Eight Hot-swappable SCSI HDDs
Dimension
Cooling Fan
Two 8cm ball-bearing fans
482(W) x 431(L) x 132.6 (H) mm
19"(W) x 16.9(L) x 5.2" (H)
Power Supply
Weight
Two 300W redundant power supply
Raid Level
Gross: 24.5kg/54lb (without HDD)
Net: 16.6kg/36.5lb (without HDD)
Support RAID 0, 1, 3, 5 and 0+1
Color
Data T ransfer Rate
Black
Drive interface: U2 SCSI
Host interface: U2 SCSI and upgradeable to
fiber channel
Support Hot-spare, Hot-swap, and on-line
auto-rebuild function
Auto failure detection, and pager & fax event
notification
OS Independent and host transparent, no
driver is required
Key-lock Hot-swappable mobile rack with
LEDs to indicate HDD status
80MB/sec
CETUS-3400
The Most Cost-effective SCSI-to-IDE RAID Subsystem
Features
Fully integrated system backplane, allows
cable-less connection to all HDDs for better
performance and reliability
Two Hot-swappable fans, located at the back
for easy maintenance
Front-side-loading Hot-swappable redundant
power supply
Specifications
Drive interface: ATA66
Host interface: U2 SCSI and upgradeable to
fiber channel
Hot-spare, Hot-swap, and on-line auto-rebuild
function support
RAID Controller
Operating Temperature Range
Equipped with Intel® i960 chipset based,
Ultra2 SCSI-ATA 66 IDE RAID controller
5 to 45˚C, 20-90%RH
Hard Disk Drive Bay
0 to 70˚C, 5-95%RH
Storage Temperature Range
Eight Hot-swappable IDE HDDs
Dimension
Cooling Fan
482(W) x 431(L) x 132.6 (H) mm
19"(W) x 16.9(L) x 5.2" (H)
Auto failure detection, and pager & fax event
notification
Two 8cm ball-bearing fans
OS Independent and host transparent, no
driver is required
Power Supply
Weight
Two 300W redundant power supply
Gross: 24.5kg/54lb (without HDD)
Net: 16.6kg/36.5lb (without HDD)
Key-lock Hot-swappable mobile rack with
LEDs to indicate HDD status
Support Raid 0, 1, 3, 5 and 0+1
Color
Data T ransfer Rate
Black
Raid Level:
80MB/sec
RAID SYSTEM
CETUS-3300