Hypno AR - Nemo Equipment
Transcription
Hypno AR - Nemo Equipment
2/7 3/7 HYPNO AR Manual Text 1. When you receive your tent, inspect the box for damage. Do not use a knife or sharp object to open the box, as you may slice the tent. 2. Layout the contents of your shipment and make sure that you received your tent and the following items: stuff sack, replacement bladder with black fitting, stakes, Silnet, Seamgrip, 2 nozzles, and repair kit. Also confirm that you received any optional items you may have ordered including: Nemoid™ foot pump, Integrated Pump, t-shirts or accessories. 3. Hypno AR comes with two types of seam sealer. Seam sealing adds strength and waterproofness to the tent and is also useful for making repairs. Use the Silnet for the EPIC and sil-nylon fabric shell of the tent. Use the Seamgrip for the airbeams and tent floor. Allow to dry overnight. Note that both seam sealers can stick to themselves even after curing, so it is best to lightly dust fully cured areas with talcum powder. Please visit www.mcnett.com for more information. 4. When packing your backpack, keep the denser objects close to your body and near your shoulders. Don’t forget to bring your NEMO pumps along! 5. Hypno AR is designed for lightweight travel, be it lightweight backpacking or adventure racing. If you are an adventure racer, you should visit www.nemoequipment.com to see the latest news about NEMO sponsored teams or inquire about sponsorship. 6. And they’re off! 7. With all that adrenaline, it’s hard not to start out running, even with 300 miles to go!! 8. Choose your campsite carefully. Avoid areas with uneven ground, under trees or near tall objects which may attract lightning, near open flames or smoldering campfires, or areas of fragile vegetation. Also consider the direction of the sun and wind. 9. NEMO AST™ tents are easy to setup at night because they are all one piece. Just be sure to keep track of your stakes and other accessories. 10. Begin the setup of your tent by staking it out. This way you have the option of inflating the tent from the inside. 11. Be sure the deflation cap is clean and screwed on tightly before inflating the tent. Make a quick visual check that the airlines and airbeams are laid out without any major kinks or twists. 12. Connect the pump to the inflation valve on the Valve Interface. If using the Nemoid™ foot pump, be sure the red intake valve on the pump is open. If using the Integrated Pump, be sure the valve on top of the pump is closed. 13. When properly connected, the CPC quick-disconnect fittings will make an audible click. 14. Step on the Nemoid™ foot pump to inflate the tent. Allow a short time between steps for the pump to refill with air. Do not use the foot pump on top of sharp objects. Inflating Burrito takes as little as 15 seconds with the Nemoid™ pump. 15. NEMO AirSupported™ tents are designed to be very strong between 5 and 7 psi. You have achieved adequate pressure when it becomes difficult to pinch the airbeam together with your fingers. Do not over-inflate! The airbeams are designed to tolerate pressures up to 25 psi in case an increase in air temperature causes the air inside the airbeam to expand. To be safe, if you setup your tent in cold weather and the temperature increases significantly, release some air to keep the pressure between 5 and 7 psi. Failure to do this in the case of extreme temperature changes can cause the airbeams to explode! 16. To pack the Nemoid™ pump, first close the red intake valve and then squeeze the pump. This will squeeze the air out of the pump, making it very compact for carrying. Simply toss the pump into the mesh pocket of the stuff sack with the tent, or into your backpack or pannier. Do not leave the foot pump compressed for more than a few days or it may not return to its original shape. 17. Hypno AR is designed to fit 2 people very comfortably or up to 4 people during an adventure race. Of course it’s a little tight for 4, but you won’t care if you haven’t slept for two days! 18. The side vents on Hypno AR can be rolled up or closed from inside the tent through the vent access zipper. If you want to keep the vent closed during high winds, clip both the vent and the tent side wall to the guyout. 19. With the side vents rolled up and the Storm Door open or just the vent deployed, Hypno AR has good air circulation and affords a nice view of the sky. 20. To take the tent down, begin by unscrewing the deflation valve. Unscrew the cap slowly to allow the pressure to decrease before the cap is released. 21. Roll the tent along the airbeams to squeeze out all the air. 22. Pack the tent into Hypno AR’s Racing Stuff Sack, roll the dry closure top and clip the sides to make it watertight. 23. The racing stuff sack is watertight so your tent stays dry and light as you endure rough weather and varying terrain. 24. Be alert for signs of changing weather. Stop in time to find a campsite away from possible flooding and other risks. 25. Begin the setup of your tent by staking it out. This way you have the option of inflating the tent from the inside. This is a unique advantage of NEMO AirSupported™ tents! If it’s raining, remember to close all zippers, including the Pump Pocket! 26. Hypno AR features a NEMO’s own Storm Door front entry. The bottom of the tent door has a horizontal zipper with an 4/7 overlapping door sill that allows you to enter and exit your tent in harsh weather without letting rain inside. 27. Once inside the tent, remove the Integrated Pump from the Pump Pocket and open the outside zipper. Reach through the Pump Pocket to connect the Integrated Pump to the Valve Interface. 28. Hypno inflates in as little as 1 minute with the Integrated Pump. 29. To use the Integrated Pump, first make sure the valve on top of the pump is closed, then blow into the pump and squeeze it with your hand or under your foot. Repeat this sequence, being sure to frequently inhale! With practice, this becomes quite effortless. Be careful not to get lightheaded! 30. When you are finished, disconnect the pump and open the valve to allow the inside of the pump to dry out. Remember to put the pump back in the Pump Pocket for next time. Also, don’t forget to close the Pump Pocket zipper! 31. The incredible ease of setting up Hypno AR means you have more time to enjoy some rest! 32. The selection of fabrics in Hypno AR not only increases its performance, but also provides a beautiful play of light in the morning sunshine. With good quality rest, you’ll be able to get a jump on everyone else. 33. Since deflation takes only a few seconds, you won’t loose any time getting back on the trail. 34. Adventure racing is about endurance, perseverance and skill. Don’t forget to stay hydrated, well-fed and take care to avoid unnecessary risks. 35. Part of adventure racing is the beautiful vistas and dramatic scenes. Whether you’re racing or backpacking, remember to appreciate and show respect for your surroundings. 36. Thanks to the dedication and perseverance of Team NEMO, combined with all the time saved by using the beautiful Hypno AR tent, the team wins again! 37. When the rain stops, it’s a good idea to air out your tent before packing it away. This will save weight and reduce the likelihood of mildew. Try to clean as much dirt and debris from your tent as possible before packing it. This will help preserve the breathability of the tent fabrics and reduce wear and tear. Always cook away from the tent! 38. The same qualities that make Hypno a great tent for adventure racing make it terrific for lightweight backpacking. It sleeps 2 very comfortably with minimal weight, great ventilation and a cozy interior. It’s a gorgeous and very unique little tent! Repair Sequence: R1. NEMO AirSupported™ tents are designed to withstand all the usual rigors of backpacking and camping. We worked hard to select materials with the right balance of being lightweight and durable. If you take reasonable care of your tent, you should never have a problem. But, accidents do happen! If you have a puncture, the next few steps will allow you how to swap in a new bladder and repair the damaged one to keep as a spare. The whole process should only take a few minutes. Please read all the steps first before beginning. R2. Every airbeam has multiple Bladder Access Pockets. Never open the access pockets when the airbeam is inflated! The bladder inside is only meant to be airtight. If it is not supported by the airbeam outer shell it will expand and pop. First disconnect the quick-disconnect fitting on the airbeam and then open the access pockets. R3. If the puncture is close to a Bladder Access Pocket, you can simply patch the bladder with the included Tear-Aid patch kit. Otherwise, simply tie a new bladder to the one inside the airbeam and pull the old one out from the opposite side, dragging the new one into place. It is best to stake down one side of the airbeam or have someone hold it while you pull the bladder through. It is very important to insert the bladder without any twists. It helps to lay the new bladder flat on the ground pointing towards the access pocket with the valve oriented the right direction. R4. Any twists in the bladder will result in obvious un-inflated portions of the airbeam when you re-inflate the airbeam. These will require repeating this entire process, so it is best to take your time and be sure the bladder is fed into the tent with the valve oriented in the right direction and without any twists. Also be sure that the bladder goes all the way to the bottom of the airbeam on both ends. Remember that the bladder requires the airbeam shell to prevent it from expanding and popping! R5. Once the new bladder is in place, secure the Bladder Access Pockets and connect the quick-disconnect fitting. If the bladder is installed correctly, the fitting should be facing towards the round hole. If you need to twist the bladder to insert the fitting through the airbeam shell, you will need to reverse this process and try inserting the bladder again. Remember, no twists! R6. After reconnecting the bladder, inflate the tent and inspect the airbeam. If the bladder is installed properly, the entire airbeam will inflate evenly and firmly from end-to-end. If there are any twists, a section of the airbeam will not inflate and become firm. If this happens, you will need to tie the old bladder onto the new one and reverse and repeat the process. R7. Repairing small holes in a NEMO bladder is simple. If necessary, inflate the bladder underwater to locate the puncture. Once you locate the puncture, make sure the area is dry and clean and cover the hole with a generous piece of the self-adhesive patch included in your repair kit. If the damage is larger than 1/8” in length or diameter, the repair may not be reliable. Replacement bladders are available from your NEMO retailer or from www.nemoequipment.com. R8. Keep the repaired bladder as a spare in a plastic bag in your stuff sack accessory pocket. It is important to keep the bladder dry and clean so that it is ready for future use. Take care not to damage the CPC quick-disconnect fitting or allow it to get dirty. 5/7 Troubleshooting and getting the most from your NEMO tent 1. I want my tent to last forever, what do I need to do? Always take care where you setup your tent. Avoid rough ground, especially rocks and pavement. Before packing the tent, make sure it is clean and dry. Store the tent unpacked to allow air circulation. Occasionally inspect the tent for wear and tear, including all of the CPC quick-disconnect fittings. If you find a damaged o-ring on a fitting, replace it with one from your repair kit. Don’t store the tent exposed to UV light. 2. I pumped up the tent and it wouldn’t hold air! The most common problem is not having the deflation valve clean and screwed tightly. Make sure the cap is clean, screw it on tightly and listen for any leaks. If the threads or inside rim of the deflation valve have been damaged, a small amount of the silicone grease included in the repair kit should fix the problem. Be aware that the grease attracts dirt! If the problem is not with the deflation valve and you can’t locate the leak by listening, than try the following procedure: 1) Disconnect the left airbeam and inflate the tent. 2) If the tent holds air, the left airbeam must be damaged. If the tent doesn’t hold air, the right airbeam must be damaged. 3) Replace the damaged bladder with one of your spares. 4) At your first opportunity, submerge the bladder in water to locate the puncture. If possible, fix the puncture with your repair kit and keep it as a spare. It is also possible that your Valve Interface™ or airlines have been damaged. If the above procedure doesn’t help, try disconnecting both airbeams and inflating. The Valve Interface™ (peanut shaped thing behind the inflation and deflation valves inside the tent) should hold the air pressure. If it does not, inspect it and all the lines carefully and listen for leaks or submerge parts of the airlines in water while inflating. If you can’t locate the leak, it may be necessary to send the tent in for repair. 3. I woke up in a puddle! Be sure all the zippers are closed tightly. The most common problem is forgetting to close the Pump Pocket zipper. Have you seam sealed your tent? In all but the most severe storms, the tent will keep the water out without the seam sealer, but seam sealing makes the tent stronger and more watertight. Also check the floor and tent shell for damage. After repeated use, you may need to replenish the Durable Water Repellent finish on the tent fabrics. This is true when water no longer beads-up on the fabrics. DWR is available from most outdoor specialty shops. 4. I pitched my tent on top of a prickly pear cactus! Hopefully you didn’t lay down on the cactus too! Carefully remove all of the spines before patching or replacing the bladder(s). If you pack the tent with spines or sharp objects inside, they could damage the remaining airbeams. The good news is that such small holes patch very easily and effectively. Follow the instructions in the repair section above. 5. My tent has a mildew smell. Always pack and store your tent dry! Mildew is not only smelly and bad for the tent materials, it is also unhealthy. Contact Rainy Pass Repair (see below) for advice about safely removing mildew. 6. Does my NEMO warranty cover this? NEMO guarantees every product we sell. We put a great effort into choosing the best materials and providing you with the highest level of workmanship. If one of our products does not meet your expectations during its useful life, we promise to repair it, replace it, exchange it, or give you a refund. 6/7 NEMO does not warranty products against normal wear and tear, unauthorized modifications or alterations, improper use, improper maintenance, misuse or neglect or if the product is used for a purpose for which it is not intended. Except as expressly set forth in these terms and conditions, NEMO is not liable for any direct, indirect or consequential damages arising out of or resulting from the use of a NEMO product. The warranties set forth in these terms and conditions are in lieu of all other warranties, express or implied, including without limitation, implied warranties of merchantability or fitness for a particular purpose. 7. I damaged my tent and need to have it repaired. If you have any problems with a NEMO product, please contact Rainy Pass Repair, Inc., the industry leader in outdoor product care for repair or replacement. If you have any questions regarding warranty and repair, or if you need to send a product in for service, please call Rainy Pass. It is not necessary to clean the item before sending, but it will be appreciated if you remove any excessive soiling. Rainy Pass will be happy to give you advice about safely cleaning your product. Please provide the following when you send a NEMO product to Rainy Pass: 1. A note indicating your name, phone number, address, email and a description of the problem. For your convenience, you can download and a repair form on the right. 2. Please remove all of your personal items and mark all damaged areas on the product with masking tape. 3. Pack the product in a sturdy cardboard box with plenty of room. We prefer to return items in their original box to reduce waste. Ship to: Rainy Pass Repair, Inc. 5307 Roosevelt Way, NE Seattle, WA 98105 To contact Rainy Pass: Phone: 1 (888) 747-7867 Email: [email protected] www.rainypass.com If you live in the Seattle area, you can call Rainy Pass locally at (206) 523-8135 and visit their shop during the following hours: M,T,W,F 9am-6pm and Th 9am-7pm. 8. I would like to contact NEMO directly. We welcome your comments and questions. If you are a NEMO customer, you were provided with a special customer service phone number. If you lost that number, please send an email to the address below. Letters should be sent to the mailing address below. Please do not send tents or other products without contacting NEMO first. Repairs and warranty issues are handled by Rainy Pass Repair. NEMO Equipment, Inc. Attn: Customer Service 100 Factory Street Nashua, NH 03060 For customer service inquiries: Email: [email protected] For all other business or inquiries: Email: [email protected] 7/7