VENTIFLEX catalogue - Ground

Transcription

VENTIFLEX catalogue - Ground
AIR DISTRIBUTION SYSTEM
VENTIFLEX
healthy
high-tech micro-silver
technology
30 years guarantee
energy saving
comfortable
ventilation
ELASTIC CHANNELS VENTILATION SYSTEM
EXTREME EASY ASEMBLING
CLEAR, HYGIENIC SURFACE
Ventiflex system consists of air ducts, distributors, diffusers and additional elements enabling
construction of any extract or supply-exhaust recuperative ventilation system. Ventiflex allows to perform
a simple and quick installation of mechanical ventilation system which can be easily fitted in gap-filling
concrete, ceilings and under dry or wet plaster coating.
micro-silver technology
guarantee sterility of the system
ADVANTAGES OF THE SYSTEM
źEasy installation – no need for any specialist tools (captive connection)
źHygiene – antistatic, anti-mould anti-bacteria properties of the internal layer help to keep the required
level of cleanness – no mould or other organisms found typically in ventilation systems are able to grow
– guaranteed high level of purity of the supplied air.
źAesthetics – small weight and high level of stiffness of Ventiflex ducts makes them fit for casting in
ceilings or gap-filling layers – aesthetics of installation. Small diameter of Ventiflex ducts allows for
installation of the system under dry plaster coating or wooden panelling.
źLow pressure loss – minimum number of joints and fittings (elbows, bents) and gentle curves for the
distribution ducts ensure minimum level of pressure loss in the system.
źNo corrosion – unlike traditional installations using galvanized spiro pipes, cut with metal cutting
blades, leading to tearing off of galvanizing layer and, in effect, to corrosion, especially in rooms highly
exposed to humidity (bathrooms, kitchens, etc.).
źSimple cleaning and maintenance – the system is able to be thoroughly cleaned due to the lack of
aluminium elastic ‘flex’ ducts or screws sticking out.
2
VENTIFLEX VT-133
INTELLIGENT TECHNOLOGY - DISCREET DESIGN
Ventiflex VT-133 is a powerful ventilation system that requires only 52 mm thick
insulation. Easy to install, thanks to its compact size the total height from the
concrete base is only 140 mm. Installation spread directly on a concrete base.
Optionally, you can lay the duct damping tape 2 mm (eg shoreline foam used in
floor). The system is equipped with all the necessary elements to construct even
the most complex ventilation system.
The floor structure of the surface heating and ventilation system VENTIFLEX VT-133
5
4
3
2
1
1) The surface (eg concrete) 2) Insulation 50 mm 3) A ventilation duct oval 133x52 mm 4) screed
(spout right) approximately 60 mm 5) Top floor coverings (tiles, laminate, parquet)
Both systems are extremely easy to install. They do not require any additional
seals and allows to assemble ventilation system for a detached house within
1 or 2 days.
3
BASIC CONSTITUENTS OF THE SYSTEM
ELASTIC DUCT: VENTIFLEX VT-DN75
DESCRIPTION:
The pipe is used for laying of air ducts in sections requiring high level of
flexibility. It is useful for laying of air ducts both on the side of supplied and
exhausted air. The ring stiffness ensures the possibility of casting
VENTIFLEX pipes in concrete ceilings.
PRODUCT FEATURES:
VENTIFLEX pipes fulfil the requirements
specified in PN-EN 61386-24:2011
standard harmonized with the EU
2006/95/EC directive.
30-years warranty on the antimicrobial
activity of the inner layer.
DIMENSIONS:
Ć 75/62; roll 50m
MATERIAL:
poliethylen, micro-silver
ative inner layer with
antistatic agent.
Pressure loss per 1 m, [Pa]
Air flow resistance in VENTIFLEX DN75 mm
Air flowrate depending of flow velocity
in VENTIFLEX DN75 pipe
U [m/s]
3
V [m /h]
Pressure loss per 1 m, [Pa]
3
Air flow rate, [m3/h]
Air flow velocity, [m/s]
4
2,0
2,5
3,0
22
27
33
TWO-CHANNELS DIFFUSER BOX: KLO-2xDN75/DN125-OC
DESCRIPTION:
Diffuser is used for fitting in VENTIFLEX systems on the side of air supply
and exhaust. It is suitable for installation both in ceilings and on walls.
Inside, it is equipped with a special air stream driver which decreases flow
resistance
DIMENSIONS:
upper connector Ć 125 x 50
side connectors Ć 75 x 50
box dimensions:
200x180x90 (width x length x height)
MATERIAL:
galvanized steel
AIR FLOW RESISTANCE (supply and exhaust):
THREE-CHANNELS DIFFUSER BOX: KLO-3xDN75/DN125-OC
DESCRIPTION: This diffuser is used for fitting in VENTIFLEX systems
on the side of air supply and exhaust. It is suitable for installation both
in ceilings and on walls. Inside, it is equipped with a special air stream
driver which decreases flow resistance.
MATERIAL:
galvanized steel
DIMENSIONS:
1 end pipe Ć 125 x 50
2 end pipe Ć 75 x 50
box dimensions:
300x180x90 (w. l. h.)
AIR FLOW RESISTANCE (supply and exhaust):
5
8-CHANNELS DISTRIBUTOR: RKL-8xDN75/DN160-OC
DESCRIPTION: This distributor is used for smaller ventilation systems.
8-channels distributor is suitable for installation on the side of both air
supply and exhaust. This distributor can be placed in concrete layers of
a building.
MATERIAL:
galvanized steel
DIMENSIONS:
1 end pipe Ć 125 x 50
8 end pipe Ć 75 x 50
box dimensions:
400x200x90 (w. l. h.)
AIR FLOW RESISTANCE (supply and exhaust):
12-CHANNELS DISTRIBUTOR: RKL-12xDN75/DN200-OC
DESCRIPTION: 12-channels distributor distributor is used with most
ventilation systems. This distributor can be installed on the side of both air
supply and exhaust. It can be placed in concrete layers of a building.
MATERIAL:
galvanized steel
DIMENSIONS:
1 end pipe Ć 125 x 50
12 end pipe Ć 75 x 50
box dimensions:
600x300x90 (w. l. h.)
AIR FLOW RESISTANCE (supply and exhaust):
6
10-CHANNELS DISTRIBUTOR STRIGHT WITH EXCHANGABLE SIDE:
SRP-10xDN75/DN200-OC, SRP-16xDN75/DN200-OC
DESCRIPTION: 10-channels distributor is used in ventilation systems
where it is possible to distribute the air within the whole building from a
single point.
DIMENSIONS:
SRP-10xDN75/DN200: 500x400x250
MATERIAL:
galvanized steel
10-CHANNELS DISTRIBUTOR STRIGHT WITH EXCHANGABLE SIDE:
SRP-16xDN75/DN200-TL
DESCRIPTION: 16-channels distributor is used in ventilation systems
where it is possible to distribute the air within the whole building from a
single point.
DIMENSIONS:
SRP-16xDN75/DN200: 820x490x250
MATERIAL:
galvanized steel
SADDLE TOP: TS-DN160-200/DN75-OC
DESCRIPTION: Used to insert a single VENTIFLEX DN75 channel
into Spiro Ø 200 or Ø 160 pipe.
DIMENSIONS:
end pipe Ć 75 x 50
saddle: Ć 200 or Ć 160
MATERIAL:
galvanized steel
SADDLE TOPS (round/flat): KS-DN160/200x50-OC ; KS-DN200/200x50-OC
DESCRIPTION: Used to insert a single VENTIFLEX DN75 channel
into Spiro Ø 200 or Ø 160 pipe.
DIMENSIONS:
end pipe Ć 75 x 50
saddle: Ć 200 or Ć 160
MATERIAL:
galvanized steel
COUPLING: ZV-DN75
DESCRIPTION: The coupling is used for connecting VENTIFLEX
DN75 pipes. Pipes are sealed with the UV-DN75 pipe joint
DIMENSIONS: Ć 75 x 116
7
MATERIAL:
polyethylene
CONTROL DAMPER WITH ACOUSTIC ATTENUATOR: PRTA-125
DESCRIPTION: Allows to control the air flow and to effectively
reduce the noise of ventilation system; especially useful in short
sections between the MANIFOLD and the air valve. The air flow can
be easily controlled by changing the number of open openings.
DIMENSION: Ć 125 x 50 mm
MATERIAŁ:
pianka poliuretanowa o wysokiej
tłumienności
PLUGS: ZA-DN75, ZA-DN125, ZA-DN160, ZA-DN200
DESCRIPTION: The plugs are used to close the unused openings of
MANIFOLDs and ATUs, as well as to secure them from getting dirty
during installation process.
DIMENSIONS:
Ć 75 , Ć 125 , Ć 160 , Ć 200 mm
PIPE SEAL:
MATERIAL:
polyethylene
UV-DN75
DESCRIPTION: The pipe seal joint is placed on VENTIFLEX elastic
pipes to ensure tightness of connection between the pipe, MANIFOLD,
ATU and connection fitting.
DIMENSIONS:
Ć 75, 8 x 5 mm (thickness, height)
MATERIAL:
EPDM
SUPPLY DIFFUSER VALVE: AN-DN125N
DESCRIPTION: This diffuser valve is mounted in the diffuser boxes
KLO-2xDN75/DN125 and KLO-3xDN75/DN125 to adjust appropriate
flowrate of the supplied/returned air.
DIMENSIONS:
Ć 145, connector - Ć 125
MATERIAL:
powder coated steel
RETURN DIFFUSER VALVE: AN-DN125W
DESCRIPTION: This diffuser valve is mounted in the diffuser boxes
KLO-2xDN75/DN125 and KLO-3xDN75/DN125 to adjust appropriate
flowrate of the supplied/returned air.
DIMENSIONS:
Ć 145, connector - Ć 125
8
MATERIAL:
powder coated steel
OVAL FLAT ELASTIC CHANNEL: VENTIFLEX VT-133
DESCRIPTION: Efficient ventilation system, requiring only 52 mm of insulation layer where it can be
installed with ease thanks to small dimensions. It is intended to be placed directly onto the concrete.
The maximum length is 12 m. The maximum exhaust flow rate is 60 m³/h.
DIMENSIONS:
133 x 52 mm (roll 20 m)
MATERIAL:
polyethylene
1-CHANNEL DIFFUSER BOX: KLP-1x133/DN125
DESCRIPTION: This diffuzer is used for installation in VENTIFLEX VT-133 systems on the side of
both air supply and exhaust. It is suitable for installation under the gap-filling layer (in the insulation
layer). It can be also placed in the concrete construction of a building. The length of the end pipe can
be extended using any fixed or flex pipe.
DIMENSIONS:
box: 180x180x55 mm
end pipe: Ć 125 x 55 mm
MATERIAL:
polyethylene
galvanized steel
2-CHANNELS DIFFUSER BOX: KLP-2x133/DN125
DESCRIPTION: This diffuzer is intended to supply/return air into/from two rooms with only one
channel. It may be used in case of two neighbour rooms, when each needs no more than 30m3/h.
DIMENSIONS:
box: 180x180x55 mm
end pipe: Ć 125 x 55 mm
MATERIAL:
polyethylene
galvanized steel
9
3-CHANNELS DISTRIBUTOR: RKP-3x133/200X50
DESCRIPTION: Distributor RKP-3x133/200x50 is used to be placed under the gap-filling layer, in the
insulation layer. They can be fixed on the side of both air supply and exhaust. Distributor can also be
placed in the concrete construction of a building.
DIMENSIONS:
3 connections 130x50 mm
1 connection 200x50 mm
box: 500x200x55
MATERIAL:
polyethylene
galvanized steel
6-CHANNELS DISTRIBUTOR: RKP-6X133/200X50
DESCRIPTION: Distributor RKP-6x133/200x50 is used to be placed under the gap-filling layer, in the
insulation layer. They can be fixed on the side of both air supply and exhaust. Distributor can also be
placed in the concrete construction of a building.
DIMENSIONS:
6 connections 130x50 mm
1 connection 200 x 50 mm
box: 950x200x55
MATERIAL:
polyethylene
galvanized steel
HORIZONTAL OVAL BEND:
KPP-133
&
VERTICAL OVAL BEND: KPL-133
DESCRIPTION: Bends make it possible to form even most complex ventilation systems.
HORIZONTAL BEND
DIMENSIONS:
180 x 180 x 52 mm
VERTICAL BEND
DIMENSIONS:
133 x 90 x 90 mm
MATERIAL:
polyethylene
10
CONNECTOR:
ZKP-133
DESCRIPTION:
Connector ZKP-133 enable channel bonding and
make it possible to form even most complex ventilation systems.
MATERIAL:
polyethylene
DIMENSIONS:
133 x 52 x 80 mm
CONNECTOR REVERSED 180O: ZKP-133/180
Such connector make it possible to turn the flat
DESCRIPTION:
channel vertically in the case of application of a bend and then to turn it
again into horizontal arrangement.
DIMENSIONS:
133 x 52 x 80 mm
MATERIAL:
polyethylene
FLAT STRAIGHT CHANNELS: KP-200X50/1000-OC
DESCRIPTION: Straight channels provide a useful solution in situations
where it is impossible to apply a half-round channel. Due to the available
dimensions, they can be placed under the gap filling.
DIMENSIONS:
200 x 50 mm
MATERIAL:
galvanized steel
SADDLE TOPS: KS-DN200/200x50 ; KS-DN160/200x50
DESCRIPTION: The tops are used for connecting round Ø200 or
Ø160 pipes with flat channels.
DIMENSIONS:
Ć 200 or Ć 160/200x50 mm
MATERIAL:
galvanized steel
HORIZONTAL ADJUSTABLE BENDS: KLN-200x50/50-90-OC
DESCRIPTION: The quarter horizontal adjustable bends make it
possible to form even most complex ventilation systems.
DIMENSIONS:
200x50 mm
MATERIAL:
galvanized steel
VERTICAL ADJUSTABLE BENDS: KSS-200x50/45-90-OC
DESCRIPTION: The quarter vertical adjustable bends make it possible
to form even most complex ventilation systems.
DIMENSIONS:
200x50 mm
MATERIAL:
galvanized steel
NOTICE: details contained on drawings and photographs are only examples and in reality may differ
from the ones shown here.
11
In order to use the full scope of functionalities of VENTIFLEX
system, Ground-Therm recommends that it is supplemented
with our GAHE (Ground-Air Heat Exchanger).
Such solution provide substantial decrease of the costs of
heating (in the winter), efficient cooling (in the summer) and
will help to create a healthy, comfortable environment inside
the building. For more details see our web side.
Ground-Therm Sp. z o.o.
ul.Chorzowska 44b
44-100 Gliwice
POLAND
tel. +48 32 231 80 20
tel./fax +48 32 230 90 47
e-mail: [email protected]
www.ground-therm.com