MULTIIMPEXЖ Company produces high

MULTIIMPEXÆ Company produces high-quality construction materials
according to the requirements of the European and international quality
standards, using environmentally friendly raw materials, know-how and
experience of European and American chemical concerns with
established names in construction chemistry.
During the years since its foundation up to now, MULTIIMPEXÆ Company
won the customersí confidence with its correctness and high quality,
and established its products on the market.
Following the world novelties and your requirements, we continuously
create new high-quality products and improve the existing ones.
Since July 2001, MULTIIMPEXÆ Company introduced the ISO 9001:2000
Quality Management System that was certified on 9 August 2001 by
ìLloydís Register Quality Assuranceî in conformity with the following
quality management systems standards:
ISO 9001:2000, EN ISO 9001:2000, BS EN ISO 9001:2000
according to the requirements of the United Kingdom Accreditation
Service (UKAS) and obtained a certificate with the sign for national
accreditation by the United Kingdom for Quality Management Systems.
The Quality Management System introduced is under the constant
control of ìLloydís Register Quality Assuranceî and is a guarantee for
permanent high quality of our products.
The team of highly qualified specialists working in MULTIIMPEXÆ Company
are ready to meat all your needs, as well as to share your ideas and
experience.
TO BUILD WITH GOOD QUALITY, USE THE MULTIIMPEXÆ PRODUCTS OF
GUARANTEED ORIGIN AND WORLD QUALITY!
WE WISH YOU SUCCESS IN THE CONSTRUCTION OF MODERN BULGARIA!
WE WILL BE DELIGHTED WITH FUTURE BENEFICIAL WORK TOGETHER
MULTIIMPEXÆ founder
Pencho Kukersky
1972 - 2002
The adhesive is a dry homogenous cement-based compound
produced according to a modern technology with environmentally friendly materials of leading world chemical
concerns.
When working with it, better adhesion to the base and improved
intrinsic strength are obtained. The adhesive has increased waterresistance and frost-resistance coefficients compared to the
construction adhesives used hitherto.
MULTICOLÆ is used to stick terracotta, faience, marble, granite,
Granitogres™ (fine stoneware tiles), stone flags, aerated
concrete and other types of cellular concrete. It is easily applied
during work and has a long open time.
One may stick directly on:
floor-heating system, lime mortar coat, concrete, cement
coating, aerated concrete, gypsum fibreboards, plasterboards,
etc. In case of wet rooms (bathrooms, swimming pools), before
applying the adhesive, the base shall be primed with GRUND-DP.
PACKING: 5, 10 and 25 kg
in three-ply paper bags
with polyethylene insert
OPERATION METHOD:
Immediately before use, add to 4 parts by weight of the dry
adhesive 1 part by weight of water. Stir manually or with a
mechanical mixer and leave for about 15 minutes so that the
components solve, then stir again and the composition thus
obtained is ready for use.
The composition is applied with a serrated mortarboard in order to achieve uniform coating. About
15-20 minutes after application, the adhesive starts to set. Soaking of the tiles in water before
sticking is not necessary.
In order to maintain the qualities of the product, the addition of cement, sand or other construction
materials is not recommended.
CONSUMPTION RATE:
For sticking tiles – 2.5-3 kg/m2
For laying aerated concrete blocks – 12-15 kg/m3
STORAGE: In original packing, stacked on wooden pallets, in dry and ventilated storerooms.
Note: Protect from moisture and water!
SHELF LIFE: 18 months
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
MULTICOLÆ adhesive for terracotta, faience, marble, granite and other linings
No.
1
2
3
4
5
6
7
INDICES
Initial tensile adhesive strength to concrete base after 28 days
Tensile adhesive strength to concrete base after 7 days in the dry and 21 days in water
Tensile adhesive strength to concrete base after heat treatment:14 days in the dry and
14 days in a drying oven at a temperature of 60∞C
Tensile adhesive strength to concrete base after freezing/defreezing cycles:
7 days in the dry, 21 days in water and 25 cycles at a temperature of -15∞C-15∞C
Tensile adhesive strength to concrete base after open time
Slippage
Open time at 23±2∞C and 55±5 % humidity
Requirements according
to BDS EN 12004
for C-1 type adhesives
≥ 0.5 N/mm2
≥ 0.5 N/mm2
≥ 0.5 N/mm2
≥ 0.5 N/mm2
≥ 0.5 N/mm2
0 ÏÏ
≥ 20 min
Complies with: BDS EN 12004 – requirements to cement-based C-1 type adhesive
PTT (product type testing) No. 011-RERECCP (Regulations on Essential Requirements and Evaluation of Conformity of Construction Products)-03.296/01.07.04.
ID No. of CAP (conformity assessment person) – 011 from the register of SAMTS (State Agency for Metrology and Technical Surveillance).
The adhesive is a dry homogenous cement-based compound
produced according to a modern technology with environmentally
friendly materials of leading world chemical concerns.
It provides better adhesion and improved intrinsic strength.
The adhesive has increased water-resistance and frost-resistance
coefficients compared to the construction adhesives used hitherto.
MULTICOL Æ White is used to stick terracotta, faience, marble,
granite, Granitogres™ (fine stoneware tiles), swimming pool tiles,
glass bricks and tiles, aerated concrete and other types of cellular
concrete. It is easily applied during work and has a long open
time.
One may stick directly on:
floor-heating system, lime mortar coat, concrete, cement coating,
aerated concrete, gypsum fibreboards, plasterboards, etc. In case
of wet rooms (bathrooms, swimming pools), before applying the
adhesive, the base shall be primed with GRUND - DP.
OPERATION METHOD:
Immediately before use, add to 4 parts by weight of the dry adhesive
1 part by weight of water. Stir manually or with a mechanical mixer
and leave for about 15 minutes so that the components solve, then
stir again and the composition thus obtained is ready for use.
PACKING: 5, 10 and 25 kg
in three-ply paper bags
with polyethylene insert
The composition is applied with a serrated mortarboard in order to achieve uniform coating. About
15-20 minutes after application, the adhesive starts to set. Soaking of the tiles in water before
sticking is not necessary. In order to maintain the qualities of the product, the addition of cement,
sand or other construction materials is not recommended.
CONSUMPTION RATE:
For sticking tiles – 2.5-3 kg/m2
For laying aerated concrete blocks – 12-15 kg/m3
STORAGE: In original packing, stacked on wooden pallets, in dry and ventilated storerooms.
Note: Protect from moisture and water!
SHELF LIFE: 18 months
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
MULTICOLÆ White adhesive for terracotta, faience, glass tiles and bricks
No.
1
2
3
4
5
6
7
INDICES
Requirements according
to BDS EN 12004
for C-1 type adhesives
Initial tensile adhesive strength to concrete base after 28 days
Tensile adhesive strength to concrete base after 7 days in the dry and 21 days in water
Tensile adhesive strength to concrete base after heat treatment:14 days in the dry and
14 days in a drying oven at a temperature of 60∞C
Tensile adhesive strength to concrete base after freezing/defreezing cycles:
7 days in the dry, 21 days in water and 25 cycles at a temperature of -15∞C-15∞C
Tensile adhesive strength to concrete base after open time
Slippage
Open time at 23±2∞C and 55±5 % humidity
Complies with: BDS EN 12004 – requirements to cement-based C-1 type adhesive
PTT No. 011-RERECCP-04.288/10.02.05. ID No. of CAP – 011 from the register of SAMTS.
≥ 0.5 N/mm2
≥ 0.5 N/mm2
≥ 0.5 N/mm2
≥ 0.5 N/mm2
≥ 0.5 N/mm2
0 ÏÏ
≥ 20 min
The adhesive is a dry homogenous cement-based compound
created according to a modern technology with environmentally
friendly materials of leading world chemical concerns – a
guarantee for high quality of the product.
It provides better adhesion and improved intrinsic strength.
The adhesive has increased water-resistance and frost-resistance
coefficients compared to the special construction adhesives used
hitherto.
It is easily applied during work and has a long open time.
MULTICOLÆ Flex is used to stick faience, terracotta, tile on tile,
marble, Granitogres™ (fine stoneware tiles), granite, stone flags,
etc.
One may stick directly on:
floor-heating system, lime mortar coat, concrete, cement coating,
aerated concrete, gypsum fibreboards, plasterboards, etc. In case
of wet rooms (bathrooms, swimming pools), before applying the
adhesive, the base shall be primed with GRUND - DP.
PACKING: 25 kg
in three-ply paper bags
with polyethylene insert
OPERATION METHOD:
Immediately before use, add to 4 parts by weight of the dry adhesive
1 part by weight of water. Stir manually or with a mechanical mixer
and leave for about 15 minutes so that the components solve, then
stir again and the composition thus obtained is ready for use.
The composition is applied with a serrated mortarboard in order to achieve uniform coating. About
15-20 minutes after application, the adhesive starts to set. Soaking of the tiles in water before
sticking is not necessary.
In order to maintain the qualities of the product, the addition of cement, sand or other construction
materials is not recommended.
CONSUMPTION RATE: For sticking tiles – 2.5-3 kg/m2
STORAGE:
In original packing, stacked on wooden pallets, in dry and ventilated storerooms.
Note: Protect from moisture and water!
SHELF LIFE: 18 months
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
MULTICOLÆ Flex high-quality flexible adhesive
No.
1
2
3
4
5
6
7
INDICES
Requirements according
to BDS EN 12004
for C-2 type adhesives
Initial tensile adhesive strength to concrete base after 28 days
Tensile adhesive strength to concrete base after 7 days in the dry and 21 days in water
Tensile adhesive strength to concrete base after heat treatment:14 days in the dry and
14 days in a drying oven at a temperature of 60∞C
Tensile adhesive strength to concrete base after freezing/defreezing cycles:
7 days in the dry, 21 days in water and 25 cycles at a temperature of -15∞C-15∞C
Tensile adhesive strength to concrete base after open time
Slippage
Open time at 23±2∞C and 55±5 % humidity
Complies with: BDS EN 12004 – requirements to cement-based C-2 type adhesive
PTT No. 011-RERECCP-04.289/10.02.05. ID No. of CAP – 011 from the register of SAMTS.
≥ 1.0 N/mm2
≥ 1.0 N/mm2
≥ 1.0 N/mm2
≥ 1.0 N/mm2
≥ 0.5 N/mm2
0 ÏÏ
≥ 30 min
The adhesive is a dry homogenous cement-based compound
created according to a modern technology with environmentally
friendly materials of leading American and German chemical
concerns – a guarantee for high quality of the product. It provides
better adhesion and improved intrinsic strength. The adhesive has
increased water-resistance and frost-resistance coefficients
compared to the special construction adhesives used hitherto. It
is easily applied during work and has a long open time.
MULTICOLÆ WHITE Flex is used to stick terracotta, faience, marble,
granite, Granitogres™ (fine stoneware tiles), stone flags, swimming
pool tiles and panels, glass tiles and bricks, glass ceramics and
other linings.
One may stick directly on:
floor-heating system, lime mortar coat, concrete, cement coating,
aerated concrete, gypsum fibreboards, plasterboards, etc. In
case of wet rooms (bathrooms, swimming pools), before applying
the adhesive, the base shall be primed with GRUND - DP.
OPERATION METHOD:
Immediately before use, add to 4 parts by weight of the dry
adhesive 1 part by weight of water. Stir manually or with a
mechanical mixer and leave for about 15 minutes so that the
components solve, then stir again and the composition thus
obtained is ready for use.
PACKING: 25 kg
in three-ply paper bags
with polyethylene insert
The composition is applied with a serrated mortarboard in order to achieve uniform coating. About
15-20 minutes after application, the adhesive starts to set. Soaking of the tiles in water before
sticking is not necessary.
In order to maintain the qualities of the product, the addition of cement, sand or other construction
materials is not recommended.
CONSUMPTION RATE: For sticking tiles – 2.5-3 kg/m2
STORAGE: In original packing, stacked on wooden pallets, in dry and ventilated storerooms.
Note: Protect from moisture and water!
SHELF LIFE: 18 months
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
MULTICOLÆ White Flex high-quality white flexible adhesive
No.
1
2
3
4
5
6
7
INDICES
Requirements according
to BDS EN 12004
for C-2 type adhesives
Initial tensile adhesive strength to concrete base after 28 days
Tensile adhesive strength to concrete base after 7 days in the dry and 21 days in water
Tensile adhesive strength to concrete base after heat treatment:14 days in the dry and
14 days in a drying oven at a temperature of 60∞C
Tensile adhesive strength to concrete base after freezing/defreezing cycles:
7 days in the dry, 21 days in water and 25 cycles at a temperature of -15∞C-15∞C
Tensile adhesive strength to concrete base after open time
Slippage
Open time at 23±2∞C and 55±5 % humidity
Complies with: BDS EN 12004 – requirements to cement-based C-2 type adhesive
PTT No. 011-RERECCP-04.290/10.02.05. ID No. of CAP – 011 from the register of SAMTS.
≥ 1.0 N/mm2
≥ 1.0 N/mm2
≥ 1.0 N/mm2
≥ 1.0 N/mm2
≥ 0.5 N/mm2
0 ÏÏ
≥ 30 min
The adhesive is a dry homogenous cement-based compound
created according to a modern technology with environmentally
friendly materials of leading American and German chemical
concerns – a guarantee for high quality of the product.
It provides better adhesion and improved intrinsic strength. The
adhesive has increased water-resistance and frost-resistance
coefficients compared to the special construction adhesives used
hitherto. It is easily applied during work and has a long open time.
MULTICOLÆ Flex 30 is a high-strength elastic adhesive for sticking
Granitogres™ (fine stoneware tiles), marble, granite, tile on tile,
stone flags and other rock facings, used on hard bases working
under static loads.
It is used for external and internal vertical and horizontal linings
under complete observance of requirements for anchoring and
fixing of heavy lining elements.
One may stick directly on:
floor-heating system, lime mortar coat, concrete, cement coating,
aerated concrete, gypsum fibreboards, plasterboards, etc. In
case of wet rooms (bathrooms, swimming pools), before applying
the adhesive, the base shall be primed with GRUND - DP.
PACKING: 25 kg
in three-ply paper bags
with polyethylene insert
OPERATION METHOD:
Immediately before use, add to 4 parts by weight of the dry
adhesive 1 part by weight of water. Stir manually or with a
mechanical mixer and leave for about 15 minutes so that the
components solve, then stir again and the composition thus
obtained is ready for use.
The composition is applied with a serrated mortarboard in order to achieve uniform coating. About
15-20 minutes after application, the adhesive starts to set. Soaking of the tiles in water before
sticking is not necessary.
In order to maintain the qualities of the product, the addition of cement, sand or other construction
materials is not recommended.
CONSUMPTION RATE: For sticking tiles – 2.5-3 kg/m2
STORAGE: In original packing, stacked on wooden pallets, in dry and ventilated storerooms.
Note: Protect from moisture and water!
SHELF LIFE: 18 months
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
MULTICOLÆ Flex 30 special high-strength elastic adhesive for ceramics
No.
1
2
3
4
5
6
7
INDICES
Requirements according
to BDS EN 12004
for C-2 type adhesives
Initial tensile adhesive strength to concrete base after 28 days
Tensile adhesive strength to concrete base after 7 days in the dry and 21 days in water
Tensile adhesive strength to concrete base after heat treatment:14 days in the dry and
14 days in a drying oven at a temperature of 60∞C
Tensile adhesive strength to concrete base after freezing/defreezing cycles:
7 days in the dry, 21 days in water and 25 cycles at a temperature of -15∞C-15∞C
Tensile adhesive strength to concrete base after open time
Slippage
Open time at 23±2∞C and 55±5 % humidity
Complies with: BDS EN 12004 – requirements to cement-based C-2 type adhesive
PTT No. 011-RERECCP-04.291/10.02.05. ID No. of CAP – 011 from the register of SAMTS.
≥ 1.0 N/mm2
≥ 1.0 N/mm2
≥ 1.0 N/mm2
≥ 1.0 N/mm2
≥ 0.5 N/mm2
0 ÏÏ
≥ 30 min
The adhesive is a dry homogenous cement-based compound
created according to a modern technology with environmentally
friendly materials of leading American and German chemical
concerns – a guarantee for high quality of the product.
It provides better adhesion and improved intrinsic strength. The
adhesive has increased water-resistance and frost-resistance
coefficients compared to the special construction adhesives used
hitherto. It is easily applied during work and has a long open
time.
MULTICOLÆ Flex 40F is a high-strength elastic adhesive for sticking
heavy facings: Granitogres™ (fine stoneware tiles), marble,
granite, stone and other rock facings, used on elastic bases
working under weak dynamic loads.
It is used for external vertical and horizontal linings under
complete observance of requirements for anchoring and fixing
of heavy lining elements.
One may stick directly on:
floor-heating system, lime mortar coat, concrete, cement
coating, aerated concrete, gypsum fibreboards, plasterboards,
etc. In case of wet rooms (bathrooms, swimming pools), before
applying the adhesive, the base shall be primed with GRUND-DP.
OPERATION METHOD:
PACKING: 25 kg
in three-ply paper bags
with polyethylene insert
Immediately before use, add to 4 parts by weight of the dry adhesive 1 part by weight of water. Stir
manually or with a mechanical mixer and leave for about 15 minutes so that the components solve,
then stir again and the composition thus obtained is ready for use.
The composition is applied with a serrated mortarboard in order to achieve uniform coating. About
15-20 minutes after application, the adhesive starts to set. Soaking of the tiles in water before
sticking is not necessary.
In order to maintain the qualities of the product, the addition of cement, sand or other construction
materials is not recommended.
CONSUMPTION RATE: For sticking tiles – 2.5-3 kg/m2
STORAGE: In original packing, stacked on wooden pallets, in dry and ventilated storerooms.
Note: Protect from moisture and water!
SHELF LIFE: 18 months
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
MULTICOLÆ Flex 40F special high-strength elastic adhesive with fibres for ceramics
No.
1
2
3
4
5
6
7
INDICES
Requirements according
to BDS EN 12004
for C-2 type adhesives
Initial tensile adhesive strength to concrete base after 28 days
Tensile adhesive strength to concrete base after 7 days in the dry and 21 days in water
Tensile adhesive strength to concrete base after heat treatment:14 days in the dry and
14 days in a drying oven at a temperature of 60∞C
Tensile adhesive strength to concrete base after freezing/defreezing cycles:
7 days in the dry, 21 days in water and 25 cycles at a temperature of -15∞C-15∞C
Tensile adhesive strength to concrete base after open time
Slippage
Open time at 23±2∞C and 55±5 % humidity
Complies with: BDS EN 12004 – requirements to cement-based C-2 type adhesive
PTT No. 011-RERECCP-04.292/10.02.05. ID No. of CAP – 011 from the register of SAMTS.
≥ 1.0 N/mm2
≥ 1.0 N/mm2
≥ 1.0 N/mm2
≥ 1.0 N/mm2
≥ 0.5 N/mm2
0 ÏÏ
≥ 30 min
TITANOL is used for sticking and preliminary thin puttying of
aerated concrete blocks, foam concrete and other types of
cellular concrete.
The adhesive is a dry homogenous cement-based compound
produced according to a modern technology with environmentally friendly materials of leading world chemical
concerns.
The adhesive is easily and quickly applied and is with a long open
time, which increases the performance when working with it, it
has high adhesive strength to the base and small consumption
rate. These properties are ideal in every aspect and are a
guarantee for the product quality.
The adhesive has increased water-resistance and frost-resistance
coefficients.
PACKING:
25 kg in three-ply paper bags
with polyethylene insert
CONSUMPTION RATE:
12-15 kg/m3
SHELF LIFE: 18 months
OPERATION METHOD:
Add to 3 parts by weight of the dry adhesive 1 part by weight of
water. Stir manually or with a mechanical mixer until obtaining a
homogeneous mass. If necessary, add water or TITANOL until
obtaining the desired working consistency.
ATTENTION!
Leave the mixture for 15-20 minutes so that the special ingredients
contained in it solve. After that interval, it is stirred again and is
already ready for use.
The composition is applied with a serrated broad knife or trowel
depending of the structure of the elements to be stuck.
In order to preserve the qualities of the product, it is not
recommended to add cement, sand or other additives.
STORAGE:
In original packing, stacked on wooden pallets, in dry and ventilated storerooms.
Note: Protect from moisture and water!
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
No.
1
2
3
4
5
VALUES
TECHNICAL DATA
Tensile adhesive strength to aerated concrete after 72 hours
Tensile adhesive strength to aerated concrete after 72 hours
and 24 hours soaking
Adhesive strength to aerated concrete after 24 hours
Adhesive strength to aerated concrete after 72 hours and
24 hours soaking
Open time at 23±2∞C and 55±5 % humidity
0.6 MPa
0.4 MPa
0.5 MPa
0.3 MPa
25 min
Issued certificate of production control system (CPCS) No. 011-RERECCP-03.297
PTT No. 011-RERECCP-192-3-62/2004
ID No. of CAP – 011 from the register of SAMTS.
The adhesive is a dry homogenous cement-based compound
produced according to a modern technology with environmentally
friendly materials of leading world chemical concerns – a
guarantee for high quality of the product.
The adhesive is used to stick ceramic bricks, lay aerated concrete
and other types of cellular concrete.
BRICKOL provides better adhesion between bricks and improved
intrinsic strength. The adhesive is easily and quickly applied and is
with a long open time, which increases the performance when
working with it, it has high adhesive strength to the base and small
consumption rate. These properties are ideal in every aspect and
are a guarantee for the product quality.
The adhesive has increased water-resistance and frost-resistance
coefficients.
OPERATION METHOD:
Immediately before work, add to 4 parts by weight of the dry
adhesive 1 part by weight of water and stir manually or with a
mechanical mixer until obtaining a homogeneous mixture.
ATTENTION:
Leave the prepared mixture for 15-20 minutes so that the special
ingredients in it solve. After that waiting time, the mixture is stirred
again and is already ready for use.
PACKING: 25 kg
in three-ply paper bags
with polyethylene insert
The application on the ceramic bricks or aerated concrete blocks is performed by means of an
appropriate tool depending of the structure of the elements to be stuck or through immersing the
ceramic bricks in the prepared solution at the surface that will be stuck.
In order to preserve the qualities of the product, it is not recommended to add cement, sand or
other additives.
CONSUMPTION RATE:
For sticking ceramic bricks – 3-4 kg/m2
For laying aerated concrete – 12-15 kg/m2
STORAGE:
In original packing, stacked on wooden pallets, in dry and ventilated storerooms.
Note: Protect from moisture and water!
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
SHELF LIFE: 18 months
Complies with: BDS EN 998PTT No. 011-RERECCP-53-3-22/2005
ID No. of CAP – 011 from the register of SAMTS.
TERMOCOLÆ is a dry homogenous compound produced on
the basis of cement, mineral fillers, polypropylene fibres and
polymer additives, which is used for sticking and puttying heatinsulating plates of extruded foamed polystyrene Styrodur,
Styrofoam, Fibran, Ursafoam, Deltadur and other trademarks,
plates of hard rock wool, perlite plates, etc.
The polypropylene fibres incorporated in the product create
optimum configuration and provide protection against cracks,
increase the impact and grinding resistance, impart residual
strength and prevent formation of non-structural cracks. All
types of plasters, fine putties and facade paints may be applied
on the puttied plates.
The adhesive is water- and frost-resistant.
OPERATION METHOD:
Add to 3 parts by weight of the adhesive 1 part by weight of
water. Stir manually or with a mechanical mixer until obtaining
a homogenous mixture.
PACKING: 20 kg
in three-ply paper bags
with polyethylene insert
CONSUMPTION RATE:
Sticking: 2.5-4 kg/m2
Puttying: 2-3 kg/m2
Attention:
The homogenous mixture thus obtained is left for 15-20 minutes
so that all special additives added to the mixture solve (an
important point for the product quality) and then stirred again.
If necessary, add water until obtaining the desired consistency.
The mixture thus prepared is ready for use.
In order to preserve the qualities of the product, it is not
recommended to add cement, sand or other additives.
STICKING:
In case of uneven base, the adhesive is applied on several places on the backside of the heatinsulating plate in order to facilitate its plumbing. In case of even surface, it is applied with a
serrated mortarboard (teeth size 8-10 mm).
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
PUTTYING:
Apply on the stuck and doweled
plates one layer of the material with
a metal mortarboard, place a glass
fibre reinforcing mesh and putty
thinly down to the level of the
reinforcing mesh until a smooth and
even surface is obtained. All types of
coloured plasters and paints may be
applied on the puttied surface after
drying of the puttied layer – up to 7
days and a temperature of not less
than 5∞C.
NOTE:
Before puttying hard rock wool
plates, it is necessary to prime with
GRUND - DP.
SHELF LIFE: 18 months
No.
1
2
3
4
5
6
7
8
TECHNICAL DATA
Tensile adhesive strength to concrete after 28 days
Tensile adhesive strength to concrete after 28 days
ageing and 24 hours soaking
Tensile adhesive strength to concrete after 28 days
ageing and 5 cycles of 24 hours soaking and
48 hours drying at 60±5∞C
Tensile adhesive strength to XPS after 28 days
Tensile adhesive strength to XPS after 28 days ageing
and 24 hours soaking
Tensile adhesive strength to XPS after 28 days ageing
and 5 cycles of soaking and 48 hours drying at 60± 5∞C
Resistance to crack formation for a layer
with a thickness of up to 5 mm
Loss after heating at 500±50∞C
VALUES
1,240 ÍN/m2
1,080 ÍN/m2
980 ÍN/m2
310 ÍN/m2
250 ÍN/m2
240 ÍN/m2
No cracks
1.68 %
Complies with: BULGARIAN TECHNICAL APPROVAL No. BTO-03.107/17.06.2004
PTT No. 011-RERECCP-03.298/07.09.2004
TAIP (Technical approval issuing person), permit No. ROSSP-09/09.05.2003
by MRDPW (Ministry of Regional Development and Public Works)
ID No. of CAP – 011 from the register of SAMTS.
STORAGE: In original packing, stacked on wooden pallets,
in dry and ventilated storerooms.
Note: Protect from moisture and water!
STIROCOLÆ is a dry homogenous compound produced on the
basis of cement, mineral fillers, polypropylene fibres and polymer
additives, which is used to stick and putty heat-insulating plates
of expanded polystyrene (Styropor) and rock wool. The
polypropylene fibres incorporated in the product create optimum
configuration and provide protection against cracks, increase
the impact and grinding resistance, impart residual strength and
prevent formation of non-structural cracks. All types of plasters,
fine putties and facade paints may be applied on the puttied
plates. The adhesive is water- and frost-resistant.
OPERATION METHOD:
Add to 3 parts by weight of the adhesive 1 part by weight of
water. Stir manually or with a mechanical mixer until obtaining a
homogenous mass.
Attention: The mixture thus obtained is left for 15-20 minutes so
that all ingredients incorporated in the mixture solve (an important
point for the adhesive quality), then stirred again and, if
necessary, water is added until obtaining the desired consistency.
The mixture thus prepared is ready for use.
In order to preserve the qualities of the product, it is not
recommended to add cement, sand or other additives.
PACKING: 20 kg
in three-ply paper bags
with polyethylene insert
STICKING:
In case of even base surface, the adhesive is applied with a serrated broad knife
(teeth size 8-10 mm).
In case of uneven base, the adhesive is applied on several places in palmate form on the backside
of the heat-insulating plate in order to facilitate its plumbing.
PUTTYING:
Apply on the stuck and doweled plates one layer of the material with a metal mortarboard, place
a glass fibre reinforcing mesh and putty thinly down to the level of the reinforcing mesh in order to
obtain a smooth and even surface. All types of plasters, putties and paints may be applied on the
puttied surface after drying of the puttied layer – up to 7 days and a temperature of not less than
5∞C.
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
CONSUMPTION RATE:
Sticking: 2.5-4 kg/m2
Puttying: 2-3 kg/m2
No.
TECHNICAL DATA
VALUES
1
2
Tensile adhesive strength to concrete after 28 days
Tensile adhesive strength to concrete after 28 days ageing
and 24 hours soaking
Tensile adhesive strength to concrete after 28 days ageing
and 5 cycles of 24 hours soaking and
48 hours drying at 60±5∞C
Tensile adhesive strength to XPS after 28 days
Tensile adhesive strength to XPS after 28 days ageing
and 24 hours soaking
Tensile adhesive strength to XPS after 28 days ageing
and 5 cycles of soaking and 48 hours drying at 60± 5∞C
Resistance to crack formation for a layer
with a thickness of up to 5 mm
Loss after heating at 500±50∞C
980 ÍN/m2
3
STORAGE:
In original packing, stacked on
wooden pallets, in dry and ventilated
storerooms.
4
5
Note:
Protect from moisture and water!
8
SHELF LIFE: 18 months
6
7
910 ÍN/m2
870 ÍN/m2
250 ÍN/m2
190 ÍN/m2
170 ÍN/m2
No cracks
1.81 %
Complies with: BULGARIAN TECHNICAL APPROVAL No. BTO-03.108/17.06.2004
PTT No. 011-RERECCP-03.299/07.09.2004
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
MINERALCOL is a dry homogenous compound produced on the
basis of cement, mineral fillers, polypropylene fibres and polymer
additives, which is used to stick and putty heat-insulating plates of
rock wool. The polypropylene fibres incorporated in the product
create optimum configuration and provide protection against
cracks, increase the impact and grinding resistance, impart
residual strength and prevent formation of non-structural cracks.
All types of plasters, fine putties and facade paints may be applied
on the puttied plates.
The adhesive is water- and frost-resistant.
OPERATION METHOD:
Add to 3 parts by weight of the adhesive 1 part by weight of water.
Stir manually or with a mechanical mixer until obtaining a
homogenous mass.
PACKING: 20 kg
in three-ply paper bags
with polyethylene insert
Attention:
The mixture thus obtained is left for 15-20 minutes so that all
ingredients incorporated in the mixture solve, an important point
for the adhesive quality, then stirred again and, if necessary, water
is added until obtaining the desired consistency. The mixture thus
prepared is ready for use.
In order to preserve the qualities of the product, it is not
recommended to add cement, sand or other additives.
STICKING:
In case of uneven base, the adhesive is applied on several places in palmate form on the backside
of the heat-insulating plate in order to facilitate its plumbing. In case of even base surface, the
adhesive is applied with a serrated broad knife (teeth size 8-10 mm).
PUTTYING:
Apply on the stuck and doweled plates one layer of the material with a metal mortarboard, place
a glass fibre reinforcing mesh and putty thinly down to the level of the reinforcing mesh until a
smooth and even surface is obtained. All types of coloured plasters and paints may be applied on
the puttied surface after drying of the puttied layer – up to 7 days and a temperature of not less
than 5∞C.
STORAGE:
In original packing, stacked on
wooden pallets, in dry and ventilated storerooms.
Note:
Protect from moisture and water!
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
No.
TECHNICAL DATA
1
2
Tensile adhesive strength to concrete after 28 days
Tensile adhesive strength to concrete after 28 days ageing
and 24 hours soaking
Tensile adhesive strength to concrete after 28 days ageing
and 5 cycles of 24 hours soaking and
48 hours drying at 60±5∞C
Tensile adhesive strength to rock wool after 28 days
Resistance to crack formation for a layer with
a thickness of up to 5 mm
3
CONSUMPTION RATE:
Sticking: 2.5-4 kg/m2
Puttying: 2-3 kg/m2
SHELF LIFE: 18 months
4
5
VALUES
760 ÍN/m2
640 ÍN/m2
610 ÍN/m2
30 ÍN/m2
No cracks
Complies with: BULGARIAN TECHNICAL APPROVAL No. BTO-04.96/07.01.2005
PTT No. 011-RERECCP-04.298/07.09.2004
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
The adhesive is a dry homogeneous compound created from
special cements according to modern technologies with
environmentally-friendly materials of leading world chemical
concerns – a guarantee for high quality of the product.
The adhesive is used to build and putty fireplaces.
With MULTICOLÆ TERMO, better adhesion to the base, improved
intrinsic strength and increased heat resistance coefficient – it
resists up to t 1,500∞C, are achieved.
The adhesive is water- and cold-resistant.
OPERATION METHOD:
Immediately before use, add to 4 parts by weight of the dry
adhesive 1 part by weight of water. Stir manually or with a
mechanical mixer and leave for about 10-15 minutes so that the
components solve. After stirring again, the composition thus
obtained is ready for use. The composition is not setting for 4-5
hours. It is applied with a serrated broad knife in order to achieve
uniform and smooth coating. About 15-20 minutes after
application, the adhesive starts to set.
The adhesive has a long open time.
In order to preserve the qualities of the product, it is not
recommended to add cement, sand or other construction
materials.
PACKING: 5 kg and 25 kg
in three-ply paper bags
with polyethylene insert
CONSUMPTION RATE:
For laying refractory bricks – 2.5-3 kg/m2
For puttying – 2-3 kg/m2
STORAGE: In original packing, stacked on wooden pallets, in dry and ventilated storerooms.
Note:
Protect from moisture and water!
SHELF LIFE: 18 months
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
Complies with: CS (Company Specification)-025-2004
Test report: CTC (Construction Testing Centre)
No. 1146-3-447/2005 of RIC (Research Institute
of Construction) EOOD
PACKING: 15 kg
in three-ply paper bags
with polyethylene insert
STORAGE:
In original packing,
stacked on wooden
pallets, in dry and
ventilated storerooms.
Note: Protect from
moisture and water!
SHELF LIFE: 18 months
The adhesive for gypsum is a dry homogenous compound on gypsum basis
and special additives controlling the setting time and other specific technical
characteristics.
USE:
The adhesive for gypsum is used for laying gypsum panels, sticking and jointing
gypsum fibreboards and plasterboards.
The gypsum compound is suitable for puttying concrete surfaces, walls of
aerated concrete blocks, lime mortar coats, as well as for sticking gypsum
cornices, ornaments, and other gypsum products.
COMPOUND PREPARATION:
Add to 2.5 parts by weight of the adhesive 1 part by weight of water. Stir
manually or with a mechanical mixer until obtaining a homogenous mass.
The mixture is left for 10 minutes, then stirred again and is ready for use. The
ready solution has a long open time of 1.30 to 2 hours. In order to preserve the
qualities of the product, it is not recommended to add cement, sand or other
construction materials.
CONSUMPTION RATE:
In case of sticking and jointing gypsum fibreboards and plasterboards –
0.750-0.900 kg/m2 depending of the joint width.
In case of puttying lime mortar coat or aerated concrete, the consumption
rate varies from 0.900 to 1.5 kg/m2.
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
No.
TECHNICAL DATA
VALUES
1 Tensile bending strength of the glue line after 24 hours
2 Tensile bending strength after 7 days
3 Compression strength after 7 days
4 Adhesive strength to gypsum base after 7 days
Complies with: BDS EN 12860, PTT No. 011-RERECCP-203-3-703/2005
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
2.2
2.1
4.2
0.8
MPa
MPa
MPa
MPa
The injection putty is used for application on old, sound base such as terracotta, faience
and Granitogres™ (fine stoneware tiles) in order to avoid their coming-off. That new
technology allows applying a new lining or other coatings of this type on the old one. The
injection putty has a high adhesion ratio, water and frost resistance.
OPERATION METHOD:
Immediately before use, add to 3 parts by weight of the dry compound 2 parts
by weight of water. Stir manually or with a mechanical mixer and leave for
PACKING: 4 kg
about 10 minutes so that the components solve. After stirring again, the
in three-ply paper bags with
composition obtained is ready for use. It does not set for about 3-4 hours. It is
polyethylene insert
applied with a roll, brush or metal mortarboard (when it is applied with a metal
CONSUMPTION RATE:
mortarboard, the composition must be made thicker). The layer applied dries
From 0.300 to 0.500 kg/m2
after 1.30-2 hours. If necessary, one more layer may be applied in order to
depending of the base and
obtain a thick coating. MULTICOLÆ Flex adhesive is applied on the surface thus
the way of application.
prepared using a serrated broad knife in order to stick terracotta, faience,
Complies with: TS(technical
Granitogres™ (fine stoneware tiles), etc. or to apply putties and pargeting.
specification)-001-2002
Adhesive strength to the base after 72 hours according to BDS 5771-85 – 3.5 MPa.
STORAGE: In dry and ventilated storerooms, stacked on wooden pallets in
original packing. Note: Protect from moisture and water!
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
BDS EN 196-6:2000
BDS EN 1542:2001 or
BDS EN 1015-12:2002
SHELF LIFE: 18 months
PACKING:
20 and 5 kg plastics buckets
and 1 kg polyethylene bottle
The adhesive is produced on the basis of polyvinyl acetate dispersion, with stabilisers
and substances controlling the setting time being used.
The adhesive is intended for
TECHNICAL DATA
VALUES
No.
use as an additive to cement,
1 Viscosity at 20∞—
Not less than 2,500 MPa.s
gypsum, and, latex paints
2 Dry substance content
Not less than 35%
when priming before painting. 3 Drying at 23±2∞C
No more than 3 h
4 Adhesive strength to paper Rupture of the paper and
STORAGE:
no rupture of the adhesive
In tightly closed containers, in
covered and dry rooms at a 5 Adhesive strength to floor
covering after 48 hours
Not less than 18 kg
temperature of 5∞C-25∞C.
Complies with: BTO-03.118/2004, PTT No. 011-RERECCP-03.309/04
Protect from freezing!
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
SHELF LIFE: 12 months
C - 200 PLUS is a water-soluble adhesive produced from polyvinyl
acetate dispersion and auxiliary additives at proper ratios.
APPLICATION: It is used for sticking wall-to-wall carpet, balatum, and
polymer floor coverings (linoleum) with textile base, floor and wall
coverings of non-woven fabrics on concrete, cement and gypsum
fibreboard surfaces.
OPERATION METHOD: The adhesive is applied with putty knife or brush
only on the surface to which the respective covering will be stuck.
No.
1
2
3
4
TECHNICAL DATA
Viscosity at 20∞—
Dry substance content
Drying at 23±2∞C
Adhesive strength to paper
VALUES
Not less than 2,800 ÃPa.s
Not less than 40%
No more 3 h
Rupture of the paper and
no rupture of the adhesive
5
Adhesive strength to floor
covering after 48 hours
Not less than 20 kg
Complies with:BTO-03.118/2004, PTT No. 011-RERECCP-03.313/2004
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
PACKING: 5 and 20 kg plastics buckets,
1 kg polyethylene bottle
CONSUMPTION RATE: 0.300 to 0.800 kg/m2
depending of the base structure.
STORAGE: In tightly closed containers, in covered
and dry rooms at a temperature of 5∞C-25∞C.
Protect from freezing!
SHELF LIFE: 12 months
PARQUETFIX is polyvinyl acetate dispersion with additives controlling the setting
time and other technical characteristics. It is intended for sticking parquet, plankboard flooring, and other wooden floor coverings directly to a previously cleaned
concrete base.
CONSUMPTION RATE:
0.400-0.600 kg/m2
PACKING: 5, 7 and 20 kg
plastics buckets
STORAGE:
In tightly closed containers, in
covered and dry rooms at a
temperature of 5∞C-25∞C.
Protect from freezing!
SHELF LIFE: 12 months
No.
TECHNICAL DATA
1
Viscosity at (23±2)∞—
2
3
Dry substance content
Tensile adhesive strength
ofthe glue line - after 7 days
under standard weather
conditions
VALUES
Not less than
2,500 MPa.s
Not less than 40%
Not less than 10 MPa
Complies with: CS-025-2004
Test report: CTC No. 198-3-68/2005 of RIC EOOD
The TERMO FIXÆ adhesive is used to stick light heat-insulating materials from
extruded and expanded polystyrene – Depron, Selitron, PenetronÆ, etc. It is
also used to stick heat-insulating rolls with a thickness (of material) of up to 10
mm (normal, backed with aluminium foil, etc) panels, plates, battens, cornices,
rosettes, etc.
The adhesive is produced from high-quality materials providing good working
consistency, excellent adhesion between the materials and the base; it imparts
water resistance and prevents the mould formation.
PACKING: 5 kg plastic buckets
CONSUMPTION RATE: 0.180-0.250 kg/m2
OPERATION METHOD: The adhesive is applied one-sidedly on
the base or the heat insulating material by means of a brush or
mortarboard at a thickness of the layer from 2 to 5 mm.
WORKING TEMPERATURE INTERVAL: 10∞C-35∞C
No.
1
2
3
TECHNICAL DATA
Dry substance content
Drying at 23±2∞C
Adhesive strength to
heat-insulating material
VALUES
Not less than 35%
Not less than 3 h
Not less than 0.2 MPa
Complies with: BTO-03.122/2004, PTT No. 011-RERECCP-03.315/2004
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
Attention: After application of the adhesive, press firmly
the heat-insulating material to the base in order to avoid
the air pocket formation.
STORAGE: In tightly closed containers, in covered and
dry rooms at a temperature of 5∞C-25∞C.
Protect from freezing!
SHELF LIFE: 12 months
The EXPRESS adhesive is produced from polyvinyl acetate dispersion, using
stabilisers, plasticisers, and other substances controlling the setting time.
When drying, the adhesive produces a transparent, smooth and elastic film. It
possesses high adhesive ability in conformity with the European quality
standards.
APPLICATION
IN THE FURNITURE INDUSTRY
To glue (manually or mechanically) wooden details and
wooden veneer. The adhesive is applied in a thin layer only
on one of the surfaces and pressure from 0.4 to 0.5 MPa is
applied for 15-20 minutes. The surfaces must be well
prepared smooth, dry, and without sawdust, which is an
important condition for quality gluing.
FOR FLOOR COVERINGS
To stick parquet, plank-board flooring, and other wooden
floor coverings. One may stick directly to previously cleaned
concrete base.
CONSUMPTION RATE: 0.180-0.250 kg/m2
STORAGE: In tightly closed containers, in covered and dry
rooms at a temperature of 5∞C-25∞C.
Protect from freezing!
SHELF LIFE: 12 months
PACKING:
5 and 20 kg plastic buckets
and 1 kg polyethylene bottle
No.
TECHNICAL DATA
VALUES
1
2
Viscosity at 23±2∞C
Dry substance content
3
Sticking strength
- after 7 days under standard
Not less than 10 MPa
weather conditions
- after 7 days at standard
weather conditions and 3 h
Not less than 8 MPa
in cold water
Complies with: CS-011-2002
Test report: CTC No. 197-3-69/2005 of RIC EOOD
Not less than 2,500 MPa.s
Not less than 40%
WORKING TEMPERATURE INTERVAL above 10∞C
QUICK CEMENT is a dry mixture of special cements and additives controlling the setting
time and strength indices. The amount of water indicated on the packing is added to the
mixture. The mixture obtained acquires very high early strength. It is used to quickly fix
parts and elements installed on frames, for openings of inspection pits, filling holes, etc.
The fixing of parts and elements takes place within 5 minutes, and full loading is applied
not earlier than in 30 minutes.
BASE PREPARATION: The base and parts should be whole and cleaned from grease
spots, etc. The crumbling sections of the base should be removed in order to ensure
good adhesion. The base shall be obligatorily primed with GRUND – DP.
The minimum layer thickness is 5 mm, the maximum one is 50 mm.
ATTENTION:
Do not add water to the mixture after the starting of the setting.
In order to preserve the qualities of the product, it is not recommended to add
cement, sand or other construction materials.
PACKING:
1 kg paper bags.
STORAGE:
In original packing, stacked on wooden pallets, in dry and ventilated storerooms.
Note: Protect from moisture and water!
SHELF LIFE: 18 months
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
Complies with: CS-030-2005, Test report: CTC No. 1145-3-446/2005 of RIC EOOD
WORKING INSTRUCTIONS: The adhesive application is done manually by means
of a suitable brush, by applying a thin layer on both surfaces to be stuck. Wait for
10-15 min. so that the sticking together of the parts takes place, before the parts
are moved, cut, or processed. The full sticking strength is reached in 24 hours.
NOTE: Clean well both surfaces before applying the adhesive. During
work, use suitable gloves and keep the packing tightly closed. The materials
used for the adhesive production are inflammable. Avoid working beside
fire and spark-producing instruments.
PACKING:
0.180 kg polyethylene bottle
CONSUMPTION RATE: 150-200 g/m2
STORAGE:
In tightly closed containers, in covered, dry, and
fire-proof rooms at a temperature of 5∞C-25∞C.
Keep away from children!
SHELF LIFE: 12 months
No.
TECHNICAL DATA
1
2
3
Dry substance content
Open time
Minimum temperature of film
formation
Sticking strength of PVC floor
covering to concrete base after
72 hours
Sticking strength for PVC/PVC
after 72 hours
4
5
VALUES
Not less than 15%
≥ 10 min
≤ 5∞—
Not less than 150 N
Not less than 100 N
Complies with: CS-011-2002
Test report: CTC No. 197-3-69/2005 of RIC EOOD
MAXPROTEKTÆ is a dry homogenous compound for puttying walls built of aerated
concrete elements, for puttying normal external plasters and smoothly cast
concrete surfaces, puttying injected chimneys, ceilings in wet premises, and laying
glass bricks.
MAXPROTEKTÆ is extremely suitable for fine (smooth) second putty when making
external or internal heat insulations if the finishing layer will be latex, faÁade paint,
faÁade silicone coatings or any type of plasters. The putty is extremely suitable for
insulation of the humidity that forms on the walls of cellars and wet premises.
Besides with spatula, the material may also be applied with whitewash brush, with
water being additionally added in this case. It is recommendable to prime the
base before use with GRUND - DP. The putty has high coefficients of water and
frost resistance, in conformity with the European quality standards.
OPERATION METHOD:
Mix together 2.5 to 3 parts by weight of the compound with 1 part by weight of
water in a plastic container, if possible, with a mechanical mixer. Leave the
compound for about 15-20 minutes so that the components in it solve, then stir
again. After its application on the wall, the putty does not dry for 15-20 minutes. If
necessary, after it had dried, it may be smoothed with expanded polystyrene or
fine sand paper glued to a rectangular board with handle. If small uneven spots
remain, they are corrected with STENOPLAST.
PACKING: 10 kg
in three-ply paper bags
with polyethylene insert.
CONSUMPTION RATE:
0.500-1.5 kg/m2 depending of the
application method
STORAGE: In dry and ventilated
storerooms, stacked on wooden
pallets in original packing.
Note:
Protect from moisture and water!
SHELF LIFE: 18 months
INDEX
No.
VALUE
Adhesive strength to concrete base
after 72 hours
Not less than 0.3 MPa
2 Adhesive strength to aerated concrete base
after 72 hours
Not less than 0.2 MPa
Not less than 1.0 MPa
3 Bending strength after 7 days
Not less than 3.5 MPa
4 Compression strength after 7 days
No cracks
5 Resistance to crack formation
Complies with: BTO-03.114/2004, PTT No. 011-RERECCP 200-03-70/2005
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
1
WORK WITHIN A TEMPERATURE INTERVAL OF 5∞C-35∞C!
Used for puttying walls built of aerated concrete elements, for puttying normal
external plasters and smoothly cast concrete surfaces, puttying injected chimneys,
ceilings in wet premises, for insulation of leakages in bathrooms and concrete
slabs.
MAXPROTEKTÆ is extremely suitable for fine (smooth) second putty when making
external or internal heat insulations if the finishing layer will be latex, faÁade paint,
faÁade silicone coatings or any type of plasters. The putty is extremely suitable for
insulation of the humidity that forms on the walls of cellars and wet premises. Besides
with spatula, the material may also be applied with whitewash brush, with water
being additionally added in this case. It is recommendable to prime the base before
use with GRUND - DP. The putty has high coefficients of water and frost resistance,
in conformity with the European quality standards.
No.
INDEX
VALUE
1
Adhesive strength to concrete base
after 72 hours
Not less than 0.3 MPa
2 Adhesive strength to aerated concrete base
after 72 hours
Not less than 0.2 MPa
3 Bending strength after 7 days
Not less than 1.0 MPa
4 Compression strength after 7 days
Not less than 3.5 MPa
5 Resistance to crack formation
No cracks
Complies with: BTO-03.114/2004, PTT No. 011-RERECCP 200-03-70/2005
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
PACKING: 10 kg in three-ply
paper bags with polyethylene insert.
CONSUMPTION RATE:
0.500-1.5 kg/m2 depending of the
application method
SHELF LIFE: 18 months
WHITE GYPSUM-BASED PUTTY COMPOUND FOR INTERIOR WALLS
AND DRY ROOMS
PLASTIKAÆ is a dry homogenous compound on gypsum basis and
special additives controlling the setting time and strength indices.
It is used for puttying concrete surfaces (panels), aerated concrete
walls, lime mortar coats, sticking and filling joints during work with
gypsum fibreboards, etc.
OPERATION METHOD: Mix together 2.5 parts by weight of the
compound with 1 part by weight of water, leave for about 10
minutes and stir again. The putty thus obtained does not harden
for about 1.30-2 hours. The base on which the putty will be applied
shall be primed with GRUND-DP. Before puttying aerated concrete
walls, they should be sprinkled with water.
CONSUMPTION RATE: On plaster – from 0.250 to 0.750 kg/m2
depending on the plaster smoothness.
On concrete surfaces (panels) – from 0.900 to 1.500 kg/m 2
depending on the surface smoothness.
STORAGE:
In dry and ventilated
storerooms, stacked on
wooden pallets in original
packing.
Note:
Protect from moisture and
water!
SHELF LIFE: 18 months
PACKING: 15 kg
in three-ply paper bags with
polyethylene insert.
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
No.
INDEX
Tensile bending strength after 7 days
1
Compression strength after 7 days
2
Tensile adhesive strength to concrete base after 3 days
3
Resistance to crack formation of a layer up to 5 mm thick
4
Chalking of the hardened putty after 3 days
5
Complies with: BTO-03.112/2004, PTT No. 011-RERECCP 194-03-64/2004
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
VALUE
≥ 1.0 N/mm2
≥ 2.5 N/mm2
≥ 0.4 N/mm2
No cracks
No chalking
The STENOPLAST putty is a white paste-like compound ready for use. It is
intended for puttying interior walls, correction of cracks and small defects
on old putties, correction of unevenness during puttying with gypsum
and cement putties..
PACKING:
5 kg plastic buckets
STORAGE: In dry and ventilated storerooms at a temperature of 5∞C-35∞C in
original packing.
Note: Protected from freezing!
SHELF LIFE: 12 months
OPERATION METHOD:
The putty is applied with a metal mortarboard or metal
spatula. The thickness of the layer applied should not
exceed 1 mm. Each following layer is applied after the
drying of the previous one. Only after the complete drying
of the puttied surface you may proceed with the painting.
CONSUMPTION RATE:
0.600-1.500 kg/m2 depending of the operation method.
WORKING TEMPERATURE INTERVAL: 5∞C-25∞C
Complies with: CS-031-2002
Test report: CTC No. 193-3-63/2005
of RIC EOOD
PACKING: 20 kg
in three-ply paper bags
with polyethylene insert
CONSUMPTION RATE:
for MULTIART-M2 – 3.2 kg/m2
SHELF LIFE: 18 months
The products represent dry homogenous compounds produced on
the basis of cement, mineral additives, polymer binders, light-resistant
pigments and other additives regulating the setting time and the time for
preservation of the working consistency.
MULTIART-M2, M3 are produced white or coloured according to
catalogue of the manufacturing company. All colours are UV rays resistant.
They may be applied on cement and gypsum putties, cement and limecement plasters, gypsum fibreboards and plasterboards, concrete panels
or on other sound and even bases. The plasters applied have excellent
behaviour during beating rain, icing and strong (direct) sunshine. The
plasters are breathing – easily pervious to water vapours. The plasters are
water- and frost-resistant and easily cleaned.
PREPARATION OF THE BASE:
The base is cleaned from dust, unstable particles, grease spots, rests of oil
paints, etc. Then, GRUND - DP shall be obligatorily applied on the even,
sound and dry base, waiting for it to dry for at least 24 hours.
PREPARATION OF THE WORKING MIXTURE:
Add to 10 parts by weight of the dry compound 2.2-2.5 parts by weight of
water in portions, stirring simultaneously with a mechanical mixer or
manually until obtaining a dense homogenous mixture. Leave it for about
20 minutes and stir again. The working mixture thus prepared is ready for
application for 2-3 hours.
APPLICATION AND TEXTURING:
The mixture prepared is applied by means of a stainless steel mortarboard
by spreading it down to the grain size both on horizontal and vertical
surfaces. Within an interval of 5-10 minutes after application (depending
on weather conditions) proceed with its structuring by means of a plastic
or rubber mortarboard (float) so that visible furrowing remains.
One may obtain a wide variety of attractive and specific individual relieves
and figures depending on the hand motion – horizontal, vertical, circular,
etc..
STORAGE:
In original packing, stacked on wooden pallets, in dry and ventilated
storerooms.
Note: Protect from moisture and water! Work within the temperature
interval +5∞C to +25∞C!
Avoid working in strong wind and direct (strong) sunlight!
SHELF LIFE: 18 months
For MULTIART-M2
Complies with: BDS EN 998-1
PTT No. 011-RERECCP 209-03-97/2005
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
For MULTIART-M3
Complies with: BDS EN 998-1
PTT No. 011-RERECCP 205-03-75/2005
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
CONSUMPTION RATE:
for MULTIART-M3 – 4.5 kg/m2
The products represent ready-to-use paste-like homogenous
compounds produced on the basis of mineral fillers and polymer
binders, light- and alkali-resistant pigments and other additives
regulating the setting time and the time for preservation of the
working consistency.
PACKING:
25 kg plastic buckets
CONSUMPTION RATE:
for MULTIART-PM2 – 2.8-3.2 kg/m2
MULTIART-PM2, PM3 are produced white or coloured
according to catalogue of the manufacturing company. All
colours are UV rays resistant. They may be applied on cement
and gypsum putties, cement and lime-cement plasters,
gypsum fibreboards and plasterboards, concrete panels or
on other sound and even bases. The plasters applied have
excellent behaviour during beating rain, icing and strong
(direct) sunshine. The plasters are breathing easily pervious
to water vapours. The plasters are water- and frost-resistant
and easily cleaned.
PREPARATION OF THE BASE:
The base is cleaned from dust, unstable particles,
grease spots, etc. GRUND - DP shall be obligatorily
applied on the even, sound and dry base, waiting for
it to dry for at least 24 hours.
PREPARATION OF THE WORKING MIXTURE:
Before use, stir vigorously the contents of the bucket.
APPLICATION AND TEXTURING:
The plaster is applied by means of a stainless steel
mortarboard by spreading it down to the grain size.
Within an interval of 5-10 minutes after application
(depending on weather conditions) proceed with
forming the desired structure by means of a plastic,
wooden or rubber mortarboard (float). One may obtain
a wide variety of relieves and figures depending on
the hand motion.
Note:
Protect the plaster applied from getting dirty for 24
hours.
Work within the temperature interval +5∞C to +25∞C!
Avoid working in strong wind and direct (strong)
sunlight!
STORAGE:
In closed and dry rooms protected from freezing
and high temperatures.
SHELF LIFE: 12 months
PACKING:
25 kg plastic buckets
CONSUMPTION RATE:
for MULTIART-PM3 – 3.5-4.2 kg/m2
RASTIKA is a dry homogenous compound produced on the basis of mineral
and polymeric binding matters, as well as other additives regulating the
physical and chemical properties and the time for preservation of the working
consistency. It is intended for application as a faÁade-decorative coating
with a relief structure on the surfaces of products of normal, light and cellular
concrete (including aerated concrete), as well as on cement and lime–
cement plasters. The plaster has an increased coefficient of water and frost
resistance.
OPERATION METHOD:
Add to 100 parts by weight of the dry plaster 30-32 parts by weight of water
and stir manually or with a mechanical mixer until obtaining a homogenous
mixture. Leave it for about 20 minutes and stir again, then it is ready for use.
RASTIKA may be applied manually – with a broad knife, roll (normal or with
relief), with a plaster-applying roll and mechanically – with a plastering
machine, depending on the effects you want to obtain. The base on which
the plaster will be applied shall be primed with deeply penetrating GRUND-DP.
NOTE: If the plaster is applied on aerated concrete, sprinkle the base with
water before application.
PACKING: 5 and 25 kg in three-ply paper
WORKING TEMPERATURE INTERVAL: 5∞C-25∞C
bags with polyethylene insert
No.
TECHNICAL DATA
VALUES
3
CONSUMPTION RATE:
Not less than 1,500 kg/m
1 Density of hardened plasters
2-3 kg/m2 depending of the application
2 Adhesive strength to concrete base
after 72 hours
Not less than 0.4 MPa
method and base structure
Not less than 0.5 MPa
3 Bending strength after 28 days
STORAGE: In original packing, stacked on
Not less than 2.0 MPa
4 Compression strength after 28 days
wooden pallets, in dry and ventilated
Not less than 20 cycles
5 Frost resistance
storerooms. Note: Avoid working in strong
Complies with: BDS EN 998-1, PTT No. 011-RERECCP 204-03-74/2005
wind and direct sunlight!
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
SHELF LIFE: 18 months
MULTIART-F is a dry homogenous compound produced on the basis of cement,
mineral additives, polymer binders and other additives regulating the time for
preservation of the working consistency. It is used as interior and exterior
decorative coating. It is applied with a brush (whitewash brush) or with a metal
mortarboard in a layer with a thickness of 1 to 6 mm depending on what structure
you wish to obtain. It may be structured with a brush, mortarboard, foamed
polyurethane sponge, and all kinds of rolls: rubber, foamed polyurethane, leather,
figural, and special depending on what figures and relieves you want to obtain.
The plaster is water- and frost-resistant, water vapour permeable (breathing) and
easy to clean. MULTIART-F may be coloured with oxide colouring agents or with
light-resistant and alkali-resistant pigmenting pastes for water dispersion paints
depending on what colour you want to obtain. The base on which the plaster will
be applied shall be primed with deeply penetrating GRUND - DP.
CONSUMPTION RATE: 1.5-4 kg/m2 depending of the thickness of the layer applied
WORKING TEMPERATURE INTERVAL: 5∞C-25∞C
PACKING:
No.
VALUES
TECHNICAL DATA
20 kg in three-ply paper bags with
polyethylene insert
Not less than 1,500 kg/m3
1 Density of hardened plasters
2 Adhesive strength to concrete base
STORAGE: In original packing, stacked on
after 72 hours
Not less than 0.4 MPa
wooden pallets, in dry and ventilated
Not less than 0.4 MPa
3 Bending strength after 28 days
storerooms. Note: Protect from moisture
Not less than 2.0 MPa
4 Compression strength after 28 days
and water! Avoid working in strong wind
Complies with: BDS EN 998-1, PTT No. 011-RERECCP 196-03-66/2005
and direct sunlight!
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
SHELF LIFE: 18 months
The plaster is a dry homogenous compound on the basis of cement,
mineral binders and additives regulating the time for preservation of the working
consistency and other physical and chemical properties.
APPLICATION: Intended for application as faÁade and interior coating on
surfaces of normal, light and cellular concrete (including aerated concrete).
OPERATION METHOD: Add to 100 parts by weight of the dry plaster 15-20
parts by weight of water and stir manually or with a mechanical mixer until
obtaining a homogenous mixture. Leave it for 15-20 minutes and stir again,
then it is ready for application. It is applied manually or mechanically with
plastering machines. The plaster is with increased coefficient of water and frost
resistance.
NOTE: If the plaster is applied on aerated concrete, it is necessary to sprinkle
previously with water the surface it is applied on.
WORKING TEMPERATURE INTERVAL: 5∞C-25∞C
No.
1
2
3
4
5
TECHNICAL DATA
Density of hardened plasters
Adhesive strength to concrete base
after 72 hours
Bending strength after 28 days
Compression strength after 28 days
Frost resistance
VALUES
Not less than 1,500kg/m
Not
Not
Not
Not
less
less
less
less
than
than
than
than
0.4 MPa
0.5 MPa
4.0 MPa
20 cycles
Complies with: BDS EN 998-1, PTT No. 011-RERECCP 201-03-71/2005
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
3
PACKING: 25 kg in three-ply paper bags
with polyethylene insert
CONSUMPTION RATE: 4-8 kg/m2
STORAGE: In original packing, stacked on
wooden pallets, in dry and venti-lated
storerooms.
Note: Protect from moisture and water!
SHELF LIFE: 18 months
GIPSOPLAST is a dry homogenous compound intended for indoor use. It may be applied
directly on aerated concrete, ceramic bricks, concrete, panels, and other sound
bases. It is applied manually or mechanically.
OPERATION METHOD: Add to 100 parts by weight of the dry plaster add 15-20 parts by
weight of water and stir manually or with a mechanical mixer until obtaining a
homogenous mixture. Leave it for 5-10 minutes and stir again. If necessary, add water
or dry compound until obtaining the necessary working consistency. The plaster retains
its working consistency for up to 1 hour, then starts setting. The application of the
compound is carried out with a metal mortarboard in a layer with a thickness of 2 mm
to 1 cm. The plaster applied may be treated up to 1 hour after its application by
smoothing it down with a mortarboard covered with porous rubber or after the
hardening it is puttied with PLASTICAÆ.
NOTE: Clean the base before applying the plaster. If necessary to apply a layer with a
thickness of more than 1 cm, you should do this in two coats.
WORKING TEMPERATURE INTERVAL: 5∞C-25∞C
No.
PACKING: 20 kg in three-ply paper
bags with polyethylene insert
CONSUMPTION RATE: 4-8 kg/m2
STORAGE: In dry and ventilated storerooms, stacked on wooden pallets in
original packing. Note: Protect from
moisture and water!
SHELF LIFE: 18 months
INDEX
VALUE
≥ 0.4 N/mm 2
1 Tensile adhesive strength to concrete
≥ 0.2 N/mm 2
2 Tensile adhesive strength to aerated concrete
≥ 1.5 N/mm 2
3 Tensile bending strength
≥ 3.0 N/mm 2
4 Compression strength
No cracks
5 Resistance to crack formation of a layer up to 10 mm thick
Complies with: BTO-03.113/01.06.2004, PTT No. 011-RERECCP-195.3.65/2004
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
OPERATION METHOD: Empty the contents of the packing in 6.5 l warm water, stir well about for about 3 minutes,
and leave for about 12 hours. The wallpapers are coated with the adhesive and are left to soften. Then, they are
hung on the wall, with the air under them being driven out by means of a piece of cloth or a roll. About 8-10 rolls
may be stuck with one package.
PACKING: 0.800 kg polyethylene bags
Tapetin-Normal is a special adhesive for sticking:
ï light paper wallpapers ï normal paper wallpapers ï heavy paper wallpapers
The adhesive is resistant to
temperature changes and features a
low consumption rate and good
sticking ability. It is water-soluble,
without insoluble particles being
formed, and allows correc-tions before
drying.
PACKING:
0.125 kg boxes
SHELF LIFE:
24 months
STORAGE: In dry and ventilated place
in original packing.
Attention: Protect from moisture and
water! Keep away from children!
No.
1
2
3
TECHNICAL DATA
Dry substance content
Õ
Drying time at 20∞C
Produced and tested according to: CS-015-2002
Operation method
Priming
Normal wallpapers
Heavy wallpapers
Dissolution of
one packing in
litres of water
m2
rolls
10
7
6
100
40
30
8
6
TAPETIN- Spezial is a special adhesive with increased synthetic resin content providing
perfect sealing and water resistance. It is used to stick relief wallpapers, fibrous wallpapers,
wallpapers from natural materials (grass, wood, cork, jute, silk, flax), fabric wallpapers,
picture wallpapers, posters, heavy paper wallpapers, and special wallpapers.
OPERATION METHOD:
Preparation of the adhesive:
Empty the contents of the packing in lukewarm water at the ratio shown in the table. Stir
well and leave for 25-30 min so that it solves, and stir again. The adhesive thus prepared is
ready for use.
Preparation of the base:
The wall must be smooth, dustless and clean from grease spots. The porous surfaces must
be primed with diluted adhesive according to the table.
Operation method
Dissolution of
one packing in
litres of water
m2
rolls
8
4
4
80
30
30
5
5
Priming
Wallpapers
Special wallpapers
No.
1
2
3
TECHNICAL DATA
Dry substance content
Õ
Drying time at 20∞C
Enough for:
VALUES
Not less than 20 %
6-7
8 min
Produced and tested according to: CS-015-2002
ï
ï
ï
ï
ï
ï
ï
ï
VALUES
Not less than 20 %
6-7
1.20 h
Enough for:
PACKING:
0.200 kg boxes
THE ADHESIVE FEATURES FOLLOWING QUALITY
CHARACTERISTICS:
low consumption rate
water resistance – suitable for damp rooms
good sticking ability
allows sticking corrections before drying
dissolves in water without insoluble particles
being formed
resistance to temperature changes
long shelf life
easy work
MULTIFLOORÆ is a powdered compound on the basis of cement, silicates,
polymers, plasticisers, and other additives controlling the physical and
chemical properties. The product consists entirely of ecological
components in conformity with the European quality standards.
MULTIFLOORÆ is intended for interior and exterior application. It is used
to smooth concrete floors during repair work and in newly constructed
buildings, when laying floor heating systems, before laying laminated
floor plates, parquet, plank-board flooring, balatum, and other floor
coverings requiring even surface, as well as only to level concrete floors.
MULTIFLOORÆ is recommended for making floors subjected to strong
loading such as production rooms, hospitals and other public buildings
that will be treated later with epoxy-based EPOXYGRUND EPG 2000 primer
and coloured epoxy-based EPOXYFLOOR floor covering, as well as other
industrial floor coverings. The floor covering thus made has a high
coefficient of wear resistance, acid resistance and may be cleaned
and disinfected easily.
PACKING: 25 kg
in three-ply paper bags
with polyethylene insert
BASE PREPARATION:
The base the self-smoothing MULTIFLOORÆ floor will be applied on must
be cleaned from grease spots, rests of gypsum and lime mortar.
Before its application, the base shall be obligatorily primed with GRUNDDP primer. Wait for the primer to dry (up to 12 hours) and then apply
MULTIFLOORÆ.
NOTE:
The base the self-smoothing MULTIFLOORÆ
floor will be applied on must be dry –
moisture content not more than 6-7 %.
MIXTURE PREPARATION:
Add to 25 parts by weight of the dry
compound 8-9 parts by weight of water
and stir with a mechanical mixer or
manually until obtaining a homogenous
mixture. If necessary, add an additional
amount of water until obtaining a
flowable consistency. Leave for 15-25
minutes so that the components solve
completely and stir again. The mixture
thus prepared is ready for application.
WORKING TEMPERATURE INTERVAL: 5∞C-25∞C
TECHNICAL DATA
No.
1
2
3
4
Adhesive strength to concrete base after:
- 3 days
- 7 days
- 28 days
Bending strength after:
- 3 days
- 7 days
- 28 days
Compression strength after:
- 3 days
- 7 days
- 28 days
Bulk density
VALUES
0.7 MPa
0.8 MPa
0.8 MPa
4.8 MPa
5.1 MPa
9.7 MPa
16.1
24.7
31.5
1.26
MPa
MPa
MPa
kg/m3
Produced and tested according to: CS-003-2002,
BDS EN 1015-1,3,4,6,9,10,11:2001; BDS EN 1542:2001, BDS EN 1015-12: 2002
APPLICATION: MULTIFLOORÆ application is started from any corner of the room helping the uniform
spreading of the mixture by means of a serrated metal mortarboard to obtain well-levelled surface.
The mixture is applied within an interval of no more than 5 minutes in order to avoid sills when individual
sections dry. The self-smoothing MULTIFLOORÆ floor thus applied hardens within up to 72 hours
depending on the humidity of the base and the air.
NOTE: MULTIFLOORÆ may be applied at a temperature
above +5∞C. Avoid working in direct sunlight and air
streams in order to prevent the quick drying and crack
formation. In view of preserving the product quality, it
is forbidden to add cement and other construction
materials.
STORAGE:
In dry and ventilated storerooms, stacked
on wooden pallets in original packing.
Note:
Protect from moisture and water!
CONSUMPTION RATE:
4-6 kg/m2 for application thickness of 3-5 mm
SHELF LIFE: 18 months
The EPOXYFLOOR epoxy composition forms monolithic floor coverings with high density;
wear and chemical resistance in various aggressive media, possibility for easy cleaning,
and esthetical appearance. The composition consists of resinous part (rich variety of
colours according to RAL CLASSIC catalogue) and hardener, which are mixed
immediately before work.
It is intended for floor covering of sites in the food industry, chemical industry, repair
shops, production areas and halls, hospitals, educational institutions, and other civil
buildings.
The composition is produced on the basis of epoxy resin and hardener imported from
Dow Chemical Company, USA. The materials have a sanitary permit issued by the
delivering company and their application is co-ordinated with the Ministry of Health
for civil construction.
Complies with: BTO-03.116/2005, PTT No. 011-RERECCP-03.308/2005
CONSUMPTION RATE:
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
1-2.5 kg/m2 depending on
ID No. of CAP – 011 from the register of SAMTS.
the floor load
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
No.
TECHNICAL DATA
VALUES
1
2
3
4
5
Appearance
Colour
Density
Viscosity at ∅ = 6 and t = 20∞C
Pot life of the composition after addition
of the hardener
Hardening time
Spreadability
Abrasion resistance according to Grasselli
Tensile bending strength
Compression strength after 7 days
Adhesive strength to concrete after 7 days
Homogenous flowable matter
According to the RAL catalogue
1.724 g/ml
186 s
6
7
8
9
10
11
45 min
14 h
195 mm
0.05 g/cm2
40.1 N/mm2
78 N/mm2
0.9 N/mm2
The EPOXYFLOOR-based floor covering
formed features high chemical
resistance in following media:
- sodium hydroxide –
various concentrations
- hydrochloric acid – 3 and 10 %
- acetic acid – 10 %
- sulphuric acid –10 and 25 %
- alcohols - methanol and ethanol
- solutions of salts, mineral oils, benzines, distilled water, antifreezes, etc.
Used as wall finishing coat. May be applied on solid, even and smooth
concrete or cement bases and putties, gypsum plasters and putties,
faience coatings, etc.
EPOXYFLOOR and EPOXYCOLOUR feature excellent technical
characteristics and performance: adhesion to the base, compression
strength, bending strength, wear resistance, resistance to bacteria,
resistance to petrol products and acids except for nitric acid.
The coatings may be easily
cleaned with suitable detergents.
CONSUMPTION RATE:
0.350-0.400 kg/m2
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
Complies with: BTO-03.116/2005
PTT No. 011-RERECCP-03.308/2005
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
The polyurethane composition forms monolithic floor coverings with high density, wear and chemical
resistance in various aggressive media, possibility for easy cleaning, and esthetical appearance.
The composition consists of modified polyurethane (rich variety of colours according to RAL CLASSIC
catalogue) and hardener, which are mixed immediately before work.
It is intended for floor covering of sites in the food industry, chemical industry, repair shops, production
areas and halls, hospitals, educational institutions, and other civil buildings.
The composition is produced on the basis of modified polyurethane and hardener imported from
Dow Chemical Company, USA. The materials have a sanitary permit issued by the delivering company
and their application is co-ordinated with the Ministry of Health for civil construction.
The polyurethane composition is weather resistant (UV rays) and has high strength and strain indices
(tension, bending, elongation, elasticity, linear and thermal expansion coefficients).
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
CONSUMPTION RATE: 1-3 kg/m2
Complies with: BTO-03.117/2004
PTT No. 011-RERECCP-03.314/2005
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
One-component air-drying composition on the basis of vinyl resin, fillers, pigments, additives, etc.
It is intended for processing of concrete floors with the purpose of preventing dust release, aesthetic
appearance and easy cleaning. This is the ideal solution for floors of sites in light industry, repair
shops, production areas and halls, educational and sports institutions, stores for raw materials and
finished products and other civil site.
The floors processed feature high weather resistance, resistance to light, moisture, water, petrol,
oils, etc.
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
CONSUMPTION RATE: 0.700-0.800 kg/m2
SILICATE-POLYMER CONCRETE is composed of dry ìAî and liquid ìBî components that, after their
mixing and application, form coating of very high quality. It is suitable for sealing cement coatings,
concrete products, washable concrete, garages, sites for handling activities, workshops, etc.
SILICATE-POLYMER CONCRETE is water-resistant coating with high compression strength and abrasion
resistance.
OPERATION METHOD: The base SILICATE-POLYMER CONCRETE will be applied on must be solid and
well cleaned from any impurities, oil paints, rests of gypsum, lime mortar, etc.
The base shall be obligatorily primed with GRUND - SPB.
Add component ìBî to component ìAî by stirring with a mechanical mixer. After homogenisation
(without granules), the mixture is left for about 10 minutes and stirred again. The mixture thus obtained
is ready for use.
The material prepared is easily applied with a metal mortarboard at a layer thickness of 5-10 mm
depending on the base loads. Attention: Do not work at temperatures above 30∞C and on surfaces
directly heated by sun in order to avoid cracking of the surface processed.
CONSUMPTION RATE: 3.5-4 kg/m2 for layer thickness of 2 mm
STORAGE: In dry and ventilated storerooms in original packing. The liquid component ìBî should be
protected from freezing and direct light.
SHELF LIFE: 18 months in original packing.
WORKING TEMPERATURE INTERVAL: 5∞C-30∞C
The coating applied is ready for use 72 hours after its application.
It is produced on the basis of epoxy resin, thinners, and
other additives.
APPLICATION: It is applied with ‡ fleecy roll with
short pile as a base before applying EPOXYFLOOR
and EPOXYCOLOUR.
It may be used for impregnation and sealing of
slightly loaded concrete floors in order to avoid
dust formation.
CONSUMPTION RATE:
0.150-0.200 kg/m2
WORKING TEMPERATURE INTERVAL: 5∞C-25∞C
The primer is an acrylic dispersion resin of high penetrating capability, which
reinforces, impregnates, and protects from penetration of humidity and
water.
APPLICATION:
ï Priming of plasters, concrete panels, concrete floors, and aerated
concrete before laying coverings and facings glued with cement based
adhesives.
ï Priming of plaster walls, gypsum fibreboards and plasterboards, aerated
concrete blocks, concrete, etc. before applying interior and exterior
plasters and putties.
ï Priming of walls before hanging wallpapers and cork facings.
ï Priming of old crumbling faÁade and interior plasters with the purpose of
their reinforcement.
ï Priming of concrete floors bases before applying self-smoothing floor
covering.
ï Priming of concrete floors before laying parquet, plank-board flooring
or other wooden floor coverings.
ï Priming stone pavements and facings, as well as decorative cement
based plates.
OPERATION METHOD:
The base the primer will be applied on must be cleaned from dust and
impurities. The primer is applied with a roll, brush, or spraying apparatus.
No.
TECHNICAL DATA
VALUES
1
2
3
Appearance and colour
Density
Viscosity at a temperature of 23±2∞C and relative air
humidity of 55±5 %
Dry substances content
pH
Drying time
Time for sphericity preservation of water drop after
application on:
- aerated concrete
- gypsum fibreboard
Penetration depth
Low-viscosity white liquid
1.02 g/cm3
4
5
6
7
8
24 s
Not less than 17 %
6-7
40 min without sticking
150 min
70 min
2 mm
Produced and tested according to: CS-006-2002, ISO 2811-1, EN 535, EN ISO 3678, 3251
PACKING:
5 kg plastic cans and
1 kg plastic bottles.
CONSUMPTION RATE:
0.150-0.200 kg/m2
WORKING TEMPERATURE
INTERVAL: 5∞C-35∞C
STORAGE:
In tightly closed containers, in
covered and dry rooms at a
temperature of 5∞C-35∞C.
Protect from freezing!
Protect from heat and direct
sunlight!
Keep away from children!
SHELF LIFE: 18 months
GRUND SPB is a product on the basis of polymer dispersion with very small grain size, which allows
deep penetration in the base capillaries, thus strengthening and sealing it.
It is used as a base before application of SILICATE-POLYMER CONCRETE, HYDROPLAST S and
HYDROPLAST STE.
OPERATION METHOD: The base GRUND SPB will be applied on must be cleaned from dust and impurities,
whereupon the primer is applied with a roll, brush, or spraying apparatus. It shall be only applied on
absorbing surfaces such as concrete, cement coatings, plasters, etc.
Attention: Do not work at temperatures above 35∞C.
CONSUMPTION RATE: 0.180-0.200 kg/m2
STORAGE:
In dry and ventilated storerooms in original packing. Protect from freezing, heating and direct light!
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
SHELF LIFE: 18 months in original packing.
SILICONPROTECT is a finishing coating that penetrates into the base
capillaries and form in depth a moisture-resistant barrier.
APPLICATION: It is used to make wet walls, concrete surfaces and
concrete products, cement bricks and roof-tiles, perlite plasters,
gypsum- and cement-based putties and plasters, smooth and relief
stone linings and other limestone, mineral and silicate linings
hydrophobic.
It is also used to ìinjectî under pressure into wet walls.
The product is clear and does not form a shiny coating.
CONSUMPTION RATE: 0.150-0.200 kg/m2
SHELF LIFE: 12 months
The contact primer was produced on the basis of acrylic polymer dispersion and additives improving
the rheology film formation.
It is used as a binding material between old strong bases with a smooth surface layer (old tiles,
smooth concrete, etc.), where normal adhesives and primer cannot have good adhesion.
OPERATION METHOD: Before use, stir vigorously the material, then apply it with a brush or roller in
thin layer.
Wait for 24 hours before subsequent processing of the base.
CONSUMPTION RATE: 0.150-0.200 kg/m2
STORAGE: In tightly closed original package in covered and dry rooms. Protect from freezing and
direct sunlight!
SHELF LIFE: 12 months in original packing.
WORKING TEMPERATURE INTERVAL: 5∞C-25∞C
The jointing compound is produced on the basis of cement, iron oxide paint,
polymers, and additives controlling the setting time.
It is used for jointing faience, terracotta, marble facings, granite, granitogres™
(fine stoneware tiles), stone facings, cleft plates, hewn plates, brick masonry,
glass brick masonry, ceramic mosaics, etc.
PACKING: 1 kg
in three-ply paper bags
with polyethylene insert
OPERATION METHOD:
Add to 3 parts by weight of the mixture 1 part by weight of water and stir
manually or with a mechanical mixer until obtaining a homogenous
mixture. Leave it for about 15 minutes so that the components solve,
then stir again. If necessary, add water to obtain the desired consistency.
The mixture thus obtained is ready for work. It is applied with rubberised
mortarboard, diagonally to the plates. After thickening, the joints are
shaped with a mortarboard with foamed polyurethane cover, or foamed
polyurethane sponge. One hour after the shaping of joints, the plates
are cleaned. After the complete drying of the joints, they may be
processed (fixed) at will with MULTIFIX or SILICONFIX.
STORAGE:
In original packing, stacked on wooden pallets, in dry and ventilated
storerooms. NOTE: Protect from moisture and water!
No.
TECHNICAL DATA
1
2
3
4
5
6
Time for setting, beginning
Adhesive strength between faience parts after 72 hours
Bending strength after 7 days
Compression strength after 7 days
Resistance to crack formation
Light resistance – no change of colour
VALUES
Not less than 60 min
Not less than 0.3 MPa
Not less than 2.0 MPa
Not less than 4.0 MPa
No cracks
After 16 hours
Complies with: BDS EN 1388, PTT No. 011-RERECCP 202-03-72/2005
TAIP, permit No. ROSSP-09/09.05.2003 by MRDPW
ID No. of CAP – 011 from the register of SAMTS.
CONSUMPTION RATE:
JOINT SIZE
5 ÏÏ
4 ÏÏ
3 ÏÏ
2 ÏÏ
DRY MASS
0. 600 Í„
0. 500 Í„
0. 400 Í„
0. 300 Í„
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
COLOUR RANGE:
30 COLOURS (according to catalogue)
SHELF LIFE: 18 months
SILICONFIX is a product on the basis of silicone emulsion. The product is characterised by deep
penetration in the joints of ceramic linings and formation of a transparent water-impervious film.
It may be applied in one or several layers, with each subsequent layer being applied after the
previous one had dried.
Attention: Do not work at temperatures above 35∞C.
CONSUMPTION RATE:
20-40 g/m2 depending on joint width and tile size.
STORAGE:
In dry and ventilated storerooms in original packing.
Protect from freezing, heating and direct light!
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
SHELF LIFE: 12 months in original packing.
MULTIFIX is a product on the basis of acrylate polymer dispersion. The product is characterised by
deep penetration in the joints of ceramic linings and formation of a transparent water-impervious
film for joints produced on cement basis.
Attention: Do not work at temperatures above 35∞C.
CONSUMPTION RATE:
20-40 g/m2 depending on joint width and tile size.
STORAGE:
In dry and ventilated storerooms in original packing.
Protect from freezing, heating and direct light!
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
SHELF LIFE: 12 months in original packing.
HYDROPLAST ST is composed of dry ìAî and liquid ìBî components on the basis of silicone
impregnating dispersion and may be easily applied in the form of putty with a mortarboard. The
covering is suitable for both interior and exterior use and has breathing effect.
OPERATION METHOD: The base HYDROPLAST ST will be applied on must be solid and well cleaned
from any impurities, oil paints, rests of gypsum, lime mortar, etc. It is desirable that the base is primed
with HYDROPLAST T – liquid hydrophobic dispersion.
Add component ìBî to component ìAî by stirring with a mechanical mixer. After homogenisation,
the mixture is left for about 10 minutes and stirred again.
The mixture thus obtained is ready for use.
The material prepared is easily applied with a metal mortarboard at a layer thickness of minimum 2
mm.
Attention: Do not work at temperatures above 30∞C and on surfaces directly heated by sun in order
to avoid cracking of the surface puttied.
CONSUMPTION RATE: 4 kg/m2 for layer thickness of 2 mm
STORAGE: In dry and ventilated storerooms in original packing.
WORKING TEMPERATURE INTERVAL: 5∞C-30∞C
SHELF LIFE: 18 months in original packing.
HYDROPLAST STE is composed of dry ìAî and liquid ìBî components that, after their mixing and
application, form a flexible and elastic membrane. The application is performed in the form of putty
with a mortarboard.
HYDROPLAST STE is applied when insulating hydraulic works and water reservoirs, swimming pools,
underground and aboveground concrete structures, etc.
OPERATION METHOD: The base HYDROPLAST ST will be applied on must be solid and well cleaned
from any impurities, oil paints, rests of gypsum, lime mortar, etc. The base shall be obligatorily primed
with HYDROPLAST T – liquid hydrophobic dispersion.
Add component ìBî to component ìAî by stirring with a mechanical mixer. After homogenisation,
the mixture is left for about 10 minutes and stirred again.
The mixture thus obtained is ready for use.
The material prepared is easily applied with a metal mortarboard at a layer thickness of 2-5 mm.
Attention: Do not work at temperatures above 30∞C and on surfaces directly heated by sun in order
to avoid cracking of the surface puttied.
CONSUMPTION RATE: 3.5-4 kg/m2 for layer thickness of 2 mm
STORAGE: In dry and ventilated storerooms in original packing. The liquid component ìBî should be
protected from freezing and direct light.
WORKING TEMPERATURE INTERVAL: 5∞C-30∞C
SHELF LIFE: 18 months in original packing
The composition applied is ready for use 72 hours after its application.
HYDROPLAST S is a powdered polymer-modified cement-based material that is applied on external
and internal surfaces, on concrete, cement coatings, etc. It is used against surface water without
pressure, against leakages and moisture.
The material is water- and frost-resistant.
OPERATION METHOD: The base HYDROPLAST S will be applied on must be solid and well cleaned
from any impurities, oil paints, rests of gypsum, lime mortar, etc. The base shall be obligatorily primed
with HYDROPLAST T – liquid hydrophobic dispersion. Add to 4 parts by weight of HYDROPLAST S 1 part
by weight of water. Stir manually or with a mechanical mixer until obtaining a homogeneous mixture.
Leave for 10-165 minutes and stir again and the mixture thus obtained is ready for use.
The material prepared is easily applied with a metal mortarboard at a layer thickness of 2 mm.
Attention: Do not work at temperatures above 30∞C and on surfaces directly heated by sun in order
to avoid cracking of the surface puttied.
CONSUMPTION RATE: 4 kg/m2 for layer thickness of 2 mm
STORAGE: In dry and ventilated storerooms in original packing.
WORKING TEMPERATURE INTERVAL: 5∞C-30∞C
SHELF LIFE: 18 months in original packing
The composition applied is ready for use 72 hours after its application.
HYDROPLAST T is a product on the basis of silicone emulsion, forming a transparent impregnating
layer after application.
HYDROPLAST T is characterised by good penetration in the base and is suitable for insulation of
moisture in concrete, bricks, lime mortar, stone, calcium-silicate bricks, etc. It is also suitable for
deeply penetrating primer before applying silicone plasters and paints.
OPERATION METHOD: The base HYDROPLAST T will be applied on must be solid and well cleaned
from dust, grease spots, etc. It may be applied on any absorbing surfaces.
It is easily applied with a roll, brush, or spraying apparatus.
Attention: Do not work at temperatures below 5∞C
CONSUMPTION RATE: 0.200-0.500 kg/m2
STORAGE: In tightly closed packing in covered and dry rooms. Protect from direct light, high
temperatures and freezing.
WORKING TEMPERATURE INTERVAL: 5∞C-30∞C
SHELF LIFE: 12 months in original packing
The AMERICAN FASAGEN-GOLD facade paint is created after the
technology of the leading German and American chemical
concerns with environmentally friendly materials.
THE PRODUCT FEATURES FOLLOWING CHARACTERISTICS:
ï High viscosity
ï Excellent covering ability
ï Increased resistance to running down
ï High coefficient of weather resistance
ï High coefficients of water and frost resistance
ï Increased coefficient of biological resistance
ï Excellent adhesion to various surfaces
PACKING:
7 and 25 kg plastic buckets
CONSUMPTION RATE:
0.230-0.280 kg/m2 depending on the base
STORAGE:
In tightly closed containers, in covered and
dry rooms at a temperature of 5∞C-25∞C.
Protect from freezing!
Protect from heat and direct sunlight!
Keep away from children!
USE:
For exterior and interior painting of elements and products made
of concrete, cellular concrete, ceramics, lime-cement plaster,
lime plaster, all types of putties, etc.
It is applied at a temperature not lower than 5∞C. The base
AMERICAN FASAGEN-GOLD is applied on must be cleaned from
dust and impurities. Before application, the base shall be primed
with GRUND - DP. The application of the paint may be carried
out manually with a brush, roll, or spraying gun with nozzle
diameter of 5 to 6 mm and at a pressure of 4 to 20 at. AMERICAN
FASAGEN-GOLD may be coloured, if necessary, with pigmenting
pastes for water dispersion paints until obtaining the desired
colour.
SHELF LIFE: 12 months
WORKING TEMPERATURE INTERVAL: 5∞C-35∞C
The AMERICAN LATEX-GOLD latex paint is created after the
technology of the leading German and American chemical
concerns with environmentally friendly materials.
THE PRODUCT FEATURES FOLLOWING CHARACTERISTICS:
ï High viscosity
ï Excellent covering ability
ï Increased resistance to running down
ï High coefficient of weather resistance
ï High coefficient of water resistance
ï Increased coefficient of biological resistance
ï Excellent adhesion to various surfaces
USE: For interior painting of elements and products made of
concrete, cellular concrete, ceramics, lime-cement plaster,
lime plaster, all types of putties, etc.
It is applied at a temperature not lower than 5∞C. The base
AMERICAN LATEX-GOLD is applied on must be cleaned from
dust and impurities. Before application, the base shall be primed
with GRUND - DP. The application of the paint may be carried
out manually with a brush, roll, or spraying gun with nozzle
diameter of 5 to 6 mm and at a pressure of 4 to 20 at. AMERICAN
LATEX-GOLD may be coloured, if necessary, with pigmenting
pastes for water dispersion paints until obtaining the desired
colour.
PACKING: 5, 7, and
25 kg plastic buckets
CONSUMPTION RATE: 0.180-0.200 kg/m2
depending on the base
STORAGE:
In tightly closed containers, in covered and
dry rooms at a temperature of 5∞C-25∞C.
Protect from freezing! Protect from heat and
direct sunlight!
Keep away from children!
SHELF LIFE: 12 months
DELTADUR E and URSAFOAM
Thickness: 20-80 mm
ìNI ECELLî Ë ìSWISSPORî
Thickness: 10-100 ÏÏ
Density: 10-35 kg/m3
Thickness: 10-100 mm
Glass wool:
ìURSAî
ìISOVERî
Rock wool:
ìROCKWOOLî
ìNOBASILî
Mesh: VERTEX – 100-160 g/m2
Dowels: For bricks and concrete
Profiles: PVC and aluminium with and without mesh, bearing socle
profile, arch profile, beak profile, profile for plaster
TERRAPLAST drainage membranes and consumables
MASTERPLAST roof foils – vapour-barrier and vapour-drainage
PLASTOMER AND ELASTOPLASTOMER (APP) MEMBRANES
SUPERTORCH, SINTEC, PERMATEC, MEGATEC,
STANDARDTEC, ULTRATEC, MAXITEC, IPERTEC
reinforcement from glass fibre mats or combined polyester
with or without slates, various thickness and weight per
sq. m.
ELASTOMER (SBS) MEMBRANES
TECH 100, TECH 500, TECH 1000, TECH 3000, TECH 5000
reinforcement from glass fibre mats or combined polyester
with or without slates, various thickness and weight per
sq. m.
UNDERTILING MEMBRANES
IPERTEC SV 800, IPERTEC T 500, RESPIRA
INCOMBUSTIBLE MEMBRANES
IPERTEC NOFLAME
COMPOSITE APP + SBS MEMBRANES
PLURA – special re-roofing membrane
PLURA R – self-adhesive membranes
PLURA THERMO AD – thermoactivating membranes
PRATIKO – cold applied membranes
MAXITEC ANTI-ROOT – anti-root membrane
MAXITEC VAPOUR BARRIER – vapour-barrier
membrane
MAXITEC VIADUCTS – for bridges and viaducts,
parking lots
PRIMERTEC – bitumen primer
IDROPRIMER – water-based bitumen primer