LOG SPLITTER

Transcription

LOG SPLITTER
OWNER’S MANUAL & OPERATING INSTRUCTIONS
35 Ton
LOG SPLITTER
MODEL NUMBER
93520
SAVE THESE INSTRUCTIONS
Important Safety Instructions
are included in this manual.
MADE IN CHINA
REV 93520-20130425
10006 Santa Fe Springs Road
Santa Fe Springs CA 90670
USA / 1-877-338-0999
www.championpowerequipment.com
AN IMPORTANT MESSAGE ABOUT TEMPERATURE:
Your Champion Power Equipment product is designed and rated for continuous operation at ambient temperatures up to
40°C (104°F). When your product is needed your product may be operated at temperatures ranging from -15°C (5°F) to
50°C (122°F) for short periods. If the product is exposed to temperatures outside this range during storage, it should be
brought back within this range before operation. In any event, the product must always be operated outdoors, in a
well-ventilated area and away from doors, windows and other vents.
Have questions or need assistance?
Do not return this product to the store!
WE ARE HERE TO HELP!
Visit our website:
www.championpowerequipment.com
for more info:
• Product Info & Updates
• Frequently Asked Questions
• Tech Bulletins
• Product Registration
– or –
Call our Customer Care Team Toll-Free at:
1-877-338-0999
WARNING:
The Engine Exhaust from this product contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
*We are always working to improve our products. Therefore, the enclosed product may differ slightly from the image on the cover.
93520
35 Ton
LOG SPLITTER
TABLE OF CONTENTS
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Portable Log Splitter. . . . . . . . . . . . . . . . . . . . . 1
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
This Booklet. . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Manual Conventions. . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Training. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Maintenance and Storage. . . . . . . . . . . . . . . . . . 6
Controls and Features . . . . . . . . . . . . . . . . . . . . . . 7
Log Splitter . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Open Shipping Crate. . . . . . . . . . . . . . . . . . . . . 8
1) Install the Hydraulic Oil Filter. . . . . . . . . . . . . 8
2) Install the Fenders . . . . . . . . . . . . . . . . . . . . 8
3) Install the Wheels. . . . . . . . . . . . . . . . . . . . . 8
4) Install the Tow Bar . . . . . . . . . . . . . . . . . . . . 8
5) Install the Beam. . . . . . . . . . . . . . . . . . . . . . 9
6) Install the Cylinder and Wedge . . . . . . . . . . . . 9
7) Install the Engine and Hoses . . . . . . . . . . . . 10
High Pressure Hose. . . . . . . . . . . . . . . . . . . 11
Suction Hose. . . . . . . . . . . . . . . . . . . . . . . 11
Oil Return Hose . . . . . . . . . . . . . . . . . . . . . 11
8) Install the Log Catcher. . . . . . . . . . . . . . . . . 11
Add Hydraulic Oil . . . . . . . . . . . . . . . . . . . . . . 11
Add Engine Oil. . . . . . . . . . . . . . . . . . . . . . . . 12
Add Engine Fuel. . . . . . . . . . . . . . . . . . . . . . . 13
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Before Each Use Inspect the Log Splitter. . . . . . 14
Towing Log Splitter Safety . . . . . . . . . . . . . . . . 14
Log Splitter Location. . . . . . . . . . . . . . . . . . . . 14
Starting the Engine. . . . . . . . . . . . . . . . . . . . . 15
Stopping the Engine . . . . . . . . . . . . . . . . . . . . 15
Log Splitter Operation. . . . . . . . . . . . . . . . . . . 16
Operation at High Altitude . . . . . . . . . . . . . . . . 17
Maintenance and Storage. . . . . . . . . . . . . . . . . . . 18
Engine Maintenance . . . . . . . . . . . . . . . . . . . . 18
Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Spark Plugs. . . . . . . . . . . . . . . . . . . . . . . .
Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . .
Log Splitter Maintenance. . . . . . . . . . . . . . . . .
Changing the Hydraulic Oil
and Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance Schedule. . . . . . . . . . . . . . . . . . .
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Log Splitter Storage . . . . . . . . . . . . . . . . . .
Engine stored for Less than 30 Days. . . . . . .
Engines Stored for Over 30 Days. . . . . . . . . .
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . .
Log Splitter Specifications. . . . . . . . . . . . . . . .
Engine Specifications . . . . . . . . . . . . . . . . . . .
Spark Plugs. . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance Valve Clearance . . . . . . . . . . . . . .
Hydraulic Oil System. . . . . . . . . . . . . . . . . . . .
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
An Important Message About Temperature. . . . .
Parts Diagram. . . . . . . . . . . . . . . . . . . . . . . . .
Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Parts Diagram . . . . . . . . . . . . . . . . . . .
Engine Parts List . . . . . . . . . . . . . . . . . . . . . .
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty Qualifications . . . . . . . . . . . . . . . . . .
Repair/Replacement Warranty. . . . . . . . . . . . . .
Do Not Return The Unit
To The Place Of Purchase . . . . . . . . . . . . . . . .
Warranty Exclusions. . . . . . . . . . . . . . . . . . . .
Normal Wear . . . . . . . . . . . . . . . . . . . . . . .
Installation, Use and Maintenance. . . . . . . . .
Other Exclusions. . . . . . . . . . . . . . . . . . . . .
Limits of Implied Warranty and
Consequential Damage . . . . . . . . . . . . . . . .
Contact Information. . . . . . . . . . . . . . . . . . . . .
Address. . . . . . . . . . . . . . . . . . . . . . . . . . .
Customer Service. . . . . . . . . . . . . . . . . . . .
Technical Service . . . . . . . . . . . . . . . . . . . .
18
18
18
19
20
20
20
20
20
20
21
22
22
22
22
22
22
22
22
22
23
24
25
26
27
27
27
27
27
27
27
27
27
27
27
27
27
ENGLISH 93520
Introduction
Introduction
Accessories
Congratulations on your purchase of a Champion
Power Equipment log splitter. CPE designs and builds
log splitters to strict specifications. With proper use
and maintenance, this log splitter will bring years of
satisfying service.
Champion Power Equipment manufactures and sells
accessories designed to help you get the most from your
purchase. To find out more please visit our website at:
www.championpowerequipment.com
Portable Log Splitter
Every effort has been made to ensure the accuracy and
completeness of the information in this manual. We reserve
the right to change, alter and/or improve the product and
this document at any time without prior notice.
This Booklet
This unit is a gasoline engine driven hydraulic log splitter.
It is designed to split wood logs for use as fire wood for
a stove or fire place. This log splitter will only split logs
lengthwise, with the grain only.
Record the model and serial numbers as well as date and place of purchase for future reference. Have this information
available when ordering parts and when making technical or warranty inquiries.
Champion Power Equipment Support
1-877-338-0999
Model Number
93520
Serial Number
Date of Purchase
Purchase Location
For Oil Type see “Add Engine Oil” section. For Fuel Type see “Add Fuel” section.
1
REV 93520-20130425
93520 ENGLISH
Manual Conventions
This manual uses the following symbols to help differentiate between different kinds of information. The safety symbol
is used with a key word to alert you to potential hazards in operating and owning power equipment.
Follow all safety messages to avoid or reduce the risk of serious injury or death.
DANGER
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
WARNING
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
CAUTION
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which, if
not avoided, may result in property damage.
NOTE
If you have questions regarding your log splitter, we can
help. Please call our help line at 1-877-338-0999
CAUTION
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury.
REV 93520-20130425
2
ENGLISH 93520
Safety Rules
WARNING
Read this manual thoroughly before operating your
log splitter. Failure to follow instructions could result
in serious injury or death.
WARNING
The engine exhaust from this product contains
chemicals known to the state of California to cause
cancer, birth defects, or other reproductive harm.
DANGER
Log Splitter engine exhaust contains carbon
monoxide, a colorless, odorless, poison gas.
Breathing carbon monoxide will cause nausea,
dizziness, fainting or death. If you start to feel dizzy
or weak, get to fresh air immediately.
Operate log splitter outdoors only in a well
ventilated area. DO NOT operate the log splitter
inside any building, enclosure or compartment.
DO NOT allow exhaust fumes to enter a confined
area through windows, doors, vents or other
openings. DANGER CARBON MONOXIDE, using a
log splitter indoors CAN KILL YOU IN MINUTES.
DANGER
Rotating parts can entangle hands, feet, hair,
clothing and/or accessories. Traumatic amputation or
severe laceration can result.
Keep hands and feet away from rotating parts. Tie up
long hair and remove jewelry. Operate equipment with
guards in place. DO NOT wear loose-fitting clothing,
dangling drawstrings or items that could become
caught.
WARNING
Operation of this equipment may create sparks that
can start fires around dry vegetation.
A spark arrestor may be required. The operator
should contact local fire agencies for laws or
regulations relating to fire prevention requirements.
3
REV 93520-20130425
DANGER
Sparks can result in fire or electrical shock.
When servicing the engine:
Disconnect the spark plug wire and place it where
it cannot contact the plug. DO NOT check for spark
with the plug removed. Use only approved spark
plug testers.
WARNING
Running engines produce heat. Severe burns can
occur on contact. Combustible material can catch
fire on contact.
DO NOT touch hot surfaces. Avoid contact with
hot exhaust gases. Allow equipment to cool before
touching. Maintain at least three feet of clearance
on all sides to ensure adequate cooling. Maintain
at least five feet of clearance from combustible
materials.
WARNING
Crush Hazard
Wedge can cut through skin and break bones. Keep
all limbs away from wedge and endplate.
WARNING
Projectile Hazard
Pieces of log may be ejected from the splitter while
operating. Wear ANSI approved safety glasses when
operating. Be alert.
WARNING
Keep Operator Work Zone Clear
Keep work zone clear of debris while working to
ensure safe footing.
93520 ENGLISH
DANGER
Skin Injection Hazard. High pressure hydraulic oil
can inject under your skin.
Make sure all fittings are tightly secure before
applying pressure. Relieve system of pressure
before servicing.
WARNING
Towing Hazard
ALWAYS check all local and state regulations
regarding towing, licensing and lights before towing
your log splitter. Review towing safety warnings in
your towing vehicle manual.
Drive safely. Be aware of the added length of the
log splitter. NEVER ride or transport cargo on the
log splitter. Choose a level surface to operate the
log splitter.
NEVER EXCEED MAX. Towing Speed 45 MPH
(72 KPH)
WARNING
Rapid retraction of the starter cord will pull hand and
arm towards the engine faster than you can let go.
Unintentional startup can result in entanglement,
traumatic amputation or laceration.
Broken bones, fractures, bruises or sprains could
result.
When starting engine, pull the starter cord slowly
until resistance is felt and then pull rapidly to avoid
kickback.
CAUTION
Parts of the hydraulic circuit (cylinder, pump, valvebody, hoses) can become very hot during operation.
Safety Rules
DANGER
Fuel and fuel vapors are highly flammable and
extremely explosive.
Fire or explosion can cause severe burns or death.
Unintentional startup can result in entanglement,
traumatic amputation or laceration.
When adding or removing fuel:
Turn the engine off and let it cool for at least two
minutes before removing the fuel cap. Loosen the
cap slowly to relieve pressure in the tank.
Only fill or drain fuel outdoors in a well-ventilated area.
DO NOT pump gas directly into the engine at the
gas station. Use an approved container to transfer
the fuel to the engine.
DO NOT overfill the fuel tank.
Always keep fuel away from sparks, open flames,
pilot lights, heat and other sources of ignition.
DO NOT light or smoke cigarettes.
When starting the engine:
DO NOT attempt to start a damaged engine. Make
certain that the gas cap, air filter, spark plug,
fuel lines and exhaust system are properly in
place. Allow spilled fuel to evaporate fully before
attempting to start the engine.
Make certain that the log splitter is resting firmly on
level ground.
When operating the log splitter:
DO NOT move or tip the log splitter during
operation.
DO NOT tip the log splitter or allow fuel or oil to
spill from the engine. Block the wheels to prevent
unintended movement.
When transporting or servicing the log splitter:
Make certain that the fuel shutoff valve is in the off
position and the fuel tank is empty.
Disconnect the spark plug wire.
When storing the log splitter:
Store away from sparks, open flames, pilot lights,
heat and other sources of ignition.
CAUTION
Improper treatment or use of the log splitter can
damage it, shorten its life and void your warranty.
Use the log splitter only for intended uses. Operate
only on level surfaces. DO NOT expose log splitter
to excessive moisture, dust, or dirt.
DO NOT allow any material to block the cooling
slots. DO NOT use the engine if:
–– Equipment sparks, smokes or emits flames
–– Equipment vibrates excessively
REV 93520-20130425
4
ENGLISH 93520
Safety Rules
5
Training
Preparation
1. Read the Operator’s Manual completely before
attempting to use this log splitter.
2. Do not allow anyone to operate your log splitter who
has not read the Operator’s Manual or has not been
instructed on the safe use of the log splitter.
3. Never allow children or untrained adults to operate
this machine.
4. Many accidents occur when more than one (1)
person operates the log splitter. If a helper is
assisting in loading logs to be split, never actuate
controls until helper is clear of the area.
5. Never allow anyone to ride on the machine.
6. Never transport cargo on the log splitter.
7. High fluid pressures are developed in hydraulic
1. Be thoroughly familiar with all controls and with
proper use of the equipment.
2. Safety Gear:
a. Always wear safety shoes or heavy boots when
operating the machine.
b. Always wear safety glasses or goggles when
operating the machine.
c. Never wear jewelry or loose-fitting clothing that
might become entangled in moving or rotating
parts of the machine.
3. Make sure the splitter is on a level surface. Block
tires and ensure support leg is secure to prevent
unintended movement of the log splitter during
operation.
log splitters. Pressurized hydraulic fluid escaping
through a pin hole opening can puncture skin
and cause sever blood poisoning. Therefore, the
following instructions should be heeded at all times.
a. Do not operate the unit with frayed, kinked,
cracked or damaged hoses, fittings, or tubing.
b. Stop the engine and relieve hydraulic system
pressure before changing or adjusting fittings,
hoses, tubing, or other system components.
c. Do not adjust the pressure settings of the pump
or valve.
d. Do not check for leaks with your hand. Leaks
can be detected by passing cardboard or wood
over the suspected area. Look for discoloration.
If injured by escaping fluid, see a doctor at
once. Serious infection or reaction can develop
if proper medical treatment is not administered
immediately.
8. Keep the operator zone and adjacent area clear for
safe, secure footing.
9. If your log splitter is equipped with an internalcombustion engine and intended for use near any
unimproved forest, brush, or grass covered land,
the engine exhaust should be equipped with a spark
arrestor. Make sure you comply with local, state,
and federal codes. Take appropriate fire-fighting
equipment with you.
10.Log splitters should be used only for splitting
wood. Do not use for other purposes unless the
manufacturer provides attachments and instructions.
a. Always operate the splitter from the
manufacturer’s indicated operator zone.
4. Logs to be split on ram-type units should be cut as
squarely as possible.
5. Fuel:
a. Use an approved fuel container.
b. Never add fuel to a running or hot engine.
c. Fill fuel tank outdoors with extreme care. Never
fill fuel tank indoors.
d. Replace gasoline cap securely and clean up any
spilled fuel.
REV 93520-20130425
93520 ENGLISH
Safety Rules
Operation
Maintenance and Storage
1. Before starting this log splitter, review all safety
rules. Failure to follow these rules may result in
serious injury to the operator or bystanders.
2. Be sure to confirm all hose connections and hose
clamps are tight before each use. It is possible for
connections to vibrate loose over time.
3. Never leave the machine unattended with the power
source operating.
4. Never operate the machine when under the
influence of alcohol, drugs or medication.
5. The machine owner should instruct all operators in
safe log splitter operation.
6. Always operate the log splitter with all safety
equipment in place and all controls properly
1. Always shut off the power source while repairing or
adjusting the splitter except as recommended by the
manufacturer.
2. Clean debris and chaff from the engine cylinder,
cylinder head fins, recoil starter cover, and muffler
areas. If the engine is equipped with a spark
arrestor muffler, clean and inspect it regularly
(follow manufacturer’s service instructions).
Replace, if damaged.
3. Never store the unit indoors with fuel in the tank.
Fumes might reach an open flame spark. Allow the
engine to cool before storing in any enclosure.
4. Clear debris from moveable parts, but only when the
power source is shut off.
adjusted for safe operation.
7. Always operate the log splitter at manufacturer’s
recommended speed.
8. Always keep hands and feet clear of moving parts.
9. When loading a ram-type log splitter, place your
hands on the sides of the log, not the ends. Never
place your hands or any part of your body between a
log and any part of the log splitter.
10.On ram-type log splitters, never attempt to split
more than one (1) log at a time unless the ram has
been fully extended and a second log is needed to
complete the separation of the first log.
11.On ram-type log splitters on which the logs are not
cut square, the longest portion of the log should be
rotated down and the most square end placed against
the ram.
12.Use only your hand to operate the log splitter
controls.
13.Do not refuel the engine until it has cooled for several
minutes.
5. Check to be sure all nuts and bolts are tight to
assure the equipment is in safe working condition.
REV 93520-20130425
6
ENGLISH 93520
Controls and Features
Read this owner’s manual before operating your log splitter. Familiarize yourself with the location and function of the
controls and features. Save this manual for future reference.
Log Splitter
10
11
12
9
13
14
8
15
7
6
5
4
3
2
16
1
18
17
(1) Beam Bracket – Holds splitting beam in place.
(10) Log Cradle – Prevents log from rolling off the beam.
(2) Beam Lock Pin – Secures in either horizontal or
vertical position.
(11) Wedge
(3) Hydraulic Pump – Pumps hydraulic oil through the
system.
(4) Hydraulic Oil Filter
(5) Wheels – Maximum travel speed is 45 MPH
(72 KPH).
(6) Fenders
(7) Log Strippers
(8) Log Catchers – Prevents split logs from falling to
the ground.
(9) Splitting Beam
7
REV 93520-20130425
(12) Control Valve Handle – Controls the movement of
the cutting wedge.
(13) Mounting Plates – Holds hydraulic cylinder in
place.
(14) Engine – 338cc, OHV, 4-stroke, air cooled.
(15) Hydraulic Cylinder – 5 in. bore (12.7 cm) x 23 in.
(58.4 cm) stroke. Rated to 3500 psi.
(16) 2” Ball Coupler – For towing the log splitter behind
your vehicle.
(17) Safety Chains – For use while towing.
(18) Support Leg – Supports log splitter while
operating. Raise leg for towing.
93520 ENGLISH
Your log splitter requires some assembly.
If you have any questions regarding the assembly of your
log splitter, call our help line at 1-877-338-0999. Please
have your serial number and model number available.
Open Shipping Crate
1. Set the shipping crate on a solid, flat surface
2. Carefully cut the shipping bands and remove lid of
shipping crate.
3. Locate all hardware before beginning assembly.
1) Install the Hydraulic Oil Filter
Install the oil filter base onto the hydraulic oil tank.
The barb fitting should be oriented vertically and once
installed the oil filter should be oriented so that it does
not extend below the hydraulic oil tank.
Assembly
3) Install the Wheels Cont’d.
5. Spin the wheel to distribute grease.
6. Loosen the castle nut and re-tighten by hand.
7. Install the cotter pin through the castle nut and axle
and spread the ends of the pin to prevent the nut from
backing off.
8. Place axle cap over castle nut and axle. Use a hammer
and wood block to seat the cap.
9. Repeat steps 1-8 for the other wheel.
NOTE
Keep the wheel hub clean and free from debris during
assembly.
CAUTION
Over-tightening the castle nut will cause the bearings to
run hot and fail prematurely.
2) Install the Fenders
1. Attach the fender to the side of the hydraulic oil tank
with an M10x30 bolt, M10 washer, M10 lock washer
and M10 nut. The safety reflector should be facing the
back of the hydraulic oil tank.
2. Repeat with second fender on opposite side.
3) Install the Wheels
1. Place bearings in the wheel hub and orient the bearing
so that the taper on the bearing matches the taper on
the hub.
2. Press the bearing seal flush into the hub. Use a
hammer and wood block to flush the seal with the end
of the hub.
3. Slide the wheel over the axel on the hydraulic oil tank.
4. Install the castle nut and tighten by hand. Tighten
another ¼ turn with a wrench to seat the bearing.
4) Install the Tow Bar
1. Assemble two piece tow bar with two M12x65 bolts
and M12 lock nuts and washers. (A)
A
2. Attach the tow bar to the bracket on top of the hydraulic
oil tank with two M12x85 bolts and M12 lock nuts. (B)
Tighten to 50 ft-lb.
B
A
To A
REV 93520-20130425
8
ENGLISH 93520
Assembly
4) Install the Tow Bar Cont’d.
5) Install the Beam Cont’d.
3. Install the front support leg and secure with pin and
R-pin (hairpin clip). (C)
5. Once the bracket on the bottom of the beam is aligned
with the tow bar, secure the beam in the horizontal
position with pin and R-pin. (C)
C
C
5) Install the Beam
1. Stand the beam upright on foot plate behind the
hydraulic oil tank. (A)
6) Install the Cylinder and Wedge
1. Place the wedge on the beam between the cylinder
mounts and slide it forward into the rails. (A)
2. Remove the cylinder mounting plates. (A)
WARNING
The beam is very heavy and should only be moved
or lifted by at least 2 able persons at all times
during assembly process. Use extreme caution to
avoid injury.
A
A
2. Slowly lift the front of the tow bar to roll the frame
toward the beam and carefully align the pivot holes
on the bottom of the beam and the top of the
hydraulic oil tank.
3. Once aligned, secure the beam to the tank with hitch
pin and R-pin. (B)
4. Hold the top of the beam by the cylinder mount and
carefully rotate the beam toward the tow bar.
B
To B
REV 93520-20130425
NOTE
The cylinder will support itself when slid all the way back
into the mounting slots.
4. Secure the cylinder mounting plates with hardware
removed in step 2. (B)
5. Slide the wedge back toward the cylinder and align
the bolt hole in the wedge with the bolt hole in the
cylinder rod. (B)
NOTE
B
9
3. Install the cylinder by sliding the pegs at the end
of the cylinder into the mounting slots on top of the
beam. Be sure to slide the cylinder all the way back
into the mounting slots. (B)
The cylinder rod may need to be rotated slightly
in order to properly align the the wedge. Insert a
screwdriver into the bolt hole in the cylinder rod
and slowly rotate as needed.
93520 ENGLISH
Assembly
6) Install the Cylinder and Wedge Cont’d.
7) Install the Engine and Hoses Cont’d.
6. Secure the wedge to the cylinder rod with an
M12x75 bolt and M12 nut. Lightly tighten the nut to
approximately 5 ft-lb. (B)
B
B
4. Connect one end of the clear oil hose to the hydraulic
oil tank just beneath the engine and the other end to
the pump inlet on the bottom of the pump. (C)
C
7) Install the Engine and Hoses
1. Attach the engine/pump to the engine mounting plate
on the hydraulic oil tank. (A) Secure with hardware
provided.
2. Place O-ring into the outlet fitting on the top of the
pump. (A)
A
5. Connect one end of the oil return hose to the outlet
barb fitting on the control valve and the other end to
the barb fitting on the oil filter. (D)
6. Install the hose retaining ring to the side of the
splitting beam. (E)
3. Connect one end of the high pressure hose to the
pump outlet fitting and the other end to the inlet on
the control valve. (B)
E
NOTE
The swivel nut end of the high pressure hose
connects to the pump outlet.
NOTE
D
The pump outlet connection does NOT require teflon
tape. The o-ring seals against the face of the fittings on
the pump and hose. Tighten to approximately 12 ft-lb.
Over-tightening can damage the pump.
REV 93520-20130425
10
ENGLISH 93520
Assembly
7) Install the Engine and Hoses Cont’d.
8) Install the Log Catcher
High Pressure Hose
1. Attach log catcher to side of beam with four M10x15
bolts, M10 lock washers, and M10 washers.
2. Repeat step 1 for the other side.
–– This is the only hose with steel connectors crimped
on both ends.
–– One end connects to the Control Valve (sealed with
teflon tape).
–– Other end connects to the top of the Pump (sealed
by O-Ring).
–– Because of the male/female ends, this hose only fits
the correct way.
Suction Hose
–– This is the clear hose that connects the hydraulic
tank to the pump inlet.
–– Both ends of the hose are secured with hose clamps
Oil Return Hose
–– This hose returns the oil exiting the cylinder to the
tank.
–– It has no connectors crimped onto it.
–– The hose ends push over barbed fittings on the
control valve and the oil filter.
–– Both ends are secured with hose clamps.
–– Notice how the hose is placed through the retainer
ring on the beam. This holds the hose close to the
frame so it does not flop out beyond the wheels (and
catch on things while towing).
Add Hydraulic Oil
1. Make sure the log splitter is on a flat, level surface.
2. Remove the oil plug from the oil tank. (A)
3. Add 7 gal. (26.5 L) of hydraulic oil - 10W AW32,
ASLE H-150, or ISO 32 are all acceptable types of
fluid.
4. Check the hydraulic oil level using the oil sight
glass. Oil level should visibly fill the glass sight. (B)
5. Replace and tighten the oil plug and orient the vent
hole away from the operator zone.
A
B
6. Start Engine. Extend and retract the wedge to purge
air from the hydraulic system. When the wedge
motion is smooth, the system is properly purged.
7. Stop the engine and check the hydraulic oil tank
sight glass. Add approximately 1 to 2 gallons
(3.79 to 7.6 L) of hydraulic oil to bring the level
back up to the sight glass.
8. Check oil level daily and add as needed.
11
REV 93520-20130425
93520 ENGLISH
Add Hyrdraulic Oil Cont’d.
NOTE
When temperature is below 32º F (0ºC) use
universal tractor/transmission fluid.
WARNING
DO NOT remove the hydraulic oil fill cap when the
engine is running or hot. Hot oil can escape causing
severe burns. Always allow the log splitter to cool
completely before removing the hydraulic oil cap.
High fluid pressure and temperatures are created
in the hydraulic log splitters. Hydraulic fluid will
escape through a pin-size hole opening and can
puncture skin and cause severe blood poisoning.
Inspect hydraulic system regularly for possible
leaks. Never check for leaks with your hand while
the system is pressurized. Seek medical attention
immediately if injured by escaping fluid.
Assembly
Add Engine Oil
CAUTION
DO NOT attempt to crank or start the engine before
it has been properly filled with the recommended
type and amount of oil. Damage to the log splitter
as a result of failure to follow these instructions will
void your warranty.
1. Make sure the log splitter is on a flat, level surface.
2. Remove oil fill cap/dipstick to add oil.
3. Add up to 1.16 qt. (1.1 L) of oil (SAE 10W-30) - oil
should cover all but 2 threads of filler hole. Replace
oil fill cap/dipstick. DO NOT OVERFILL.
4. Check engine oil level daily and add as needed.
CAUTION
The engine is equipped with a low oil shut-off and
will stop when the oil level in the crankcase falls
below the threshold level.
NOTE
Check oil often during the break-in period. Refer to
the Maintenance section for recommended service
intervals.
REV 93520-20130425
12
ENGLISH 93520
Assembly
Add Fuel
1. Use clean, fresh, regular unleaded fuel with a
minimum octane rating of 85 and an ethanol
content of less than 10% by volume.
2. DO NOT mix oil with fuel.
3. Clean the area around the fuel cap.
4. Remove the fuel cap.
5. Slowly add fuel to the tank. DO NOT OVERFILL.
Fuel can expand after filling. A minimum of ¼ in.
(0.64 cm) of space left in the tank is required
for fuel expansion, more than ¼ in. (0.64 cm) is
recommended. Fuel can be forced out of the tank
as a result of expansion if it is overfilled, and can
affect the stable running condition of the product.
When filling the tank, it is recommended to leave
enough space for the fuel to expand.
Add Fuel Cont’d.
CAUTION
Use regular unleaded gasoline with a minimum
octane rating of 85.
Do not mix oil and gasoline.
Fill tank to approximately ¼ in. (0.64 cm) below
the top of the tank to allow for fuel expansion.
DO NOT pump gas directly into the tank at the gas
station. Use an approved container to transfer the
fuel to the tank.
DO NOT fill fuel tank indoors.
DO NOT fill fuel tank when the engine is running or hot.
DO NOT overfill the fuel tank.
DO NOT light cigarettes or smoke when filling the
fuel tank.
NOTE
6. Screw on the fuel cap and wipe away any spilled
fuel.
WARNING
Pouring fuel too fast through the fuel screen may
result in blow back of fuel at the operator while
filling.
13
REV 93520-20130425
Our engines work well with 10% or less ethanol
blend fuels. When using blended fuels there are
some issues worth noting:
–– Ethanol-gasoline blends can absorb more water
than gasoline alone.
–– These blends can eventually separate, leaving
water or a watery goo in the tank, fuel valve and
carburetor.
–– With gravity-fed fuel supplies, this compromised
fuel can be drawn into the carburetor and cause
damage to the engine and/or potential hazards.
–– There are only a few suppliers of fuel stabilizer
that are formulated to work with ethanol blend
fuels.
–– Any damages or hazards caused by using
improper fuel, improperly stored fuel, and/
or improperly formulated stabilizers, are not
covered by manufacture’s warranty.
It is advisable to always shut off the fuel supply,
run the engine to fuel starvation and drain the tank
when the equipment is not in use for more than 30
days.
93520 ENGLISH
Operation
Before Each Use Inspect the Log Splitter
Log Splitter Location Cont’d.
1. Check the hydraulic oil level and visually inspect all
hoses, attachments and cylinder for loose fittings,
leaks, cracks, fraying or other damage.
2. DO NOT operate the log splitter if there is any
indication of damage.
3. Inspect the engine and make sure the oil level is
correct before operating. If the engine is equipped
with a spark arrestor, clean and inspect it regularly
(follow spark arrestor maintenance schedule).
4. The tires need to be fully inflated and in good repair.
Reference the tire sidewall for recommended tire
pressure.
The log splitter needs to be on a dry level surface with
good footing. DO NOT work on mud, ice, tall grass,
brush or snow.
Only operate log splitter from work zones shown below.
W
Zo
e
n
DO NOT over inflate tires. Serious injury can result
if tires explode.
DO NOT tow the log splitter if the tires are worn or
will not hold air.
DO NOT exceed the maximum 45 MPH (72 KPH)
towing speed.
or
k
WARNING
Horizontal Operating
Position
Towing Log Splitter Safety
1. Always check local and state regulations regarding the
requirements for towing, licensing and lights.
2. Before towing make sure the log splitter is correctly
and securely attached to the vehicle and the safety
chains attached with enough slack to allow for turning.
3. Support leg must be pinned in the “UP” position for
towing.
4. Never exceed the max. travel speed of 45 mph. Towing
the log splitter at speeds greater than 45 mph could
result in serious injury or death. Always adjust your
towing speed according to the terrain and conditions.
5. Always disconnect the log splitter from the towing
vehicle before operating.
Log Splitter Location
This log splitter must have at least seven feet of
clearance from combustible material. Leave at least
three feet of clearance on all sides of the log splitter to
allow for adequate cooling, maintenance and servicing.
DO NOT place the log splitter near vents or intakes
where engine exhaust fumes could be drawn into
occupied or confined spaces. ONLY operate the log
splitter outdoors.
Vertical Operating
Position
Wo
rk Zone
NOTE
For Vertical Operation:
–– Remove the beam lock-pin from the beam
bracket
–– Use handle on cylinder to rotate beam to vertical
position
–– Insert beam lock-pin in the pivot bracket
REV 93520-20130425
14
ENGLISH 93520
Operation
Log Splitter Location Cont’d.
WARNING
ALWAYS use the log splitter for its intended use. The
log splitter should only be used to split wood logs,
length wise with the grain.
NEVER modify, alter or change the log splitter in
anyway. Modifications will void the warranty.
NEVER attach a rope, cable or other device to the
control lever on the log splitter.
DO NOT modify or change the engine and operating
speeds or pressure settings. These changes can
cause safety issues.
ONLY operate the log splitter in daylight.
NEVER operate, or let anyone else operate, the log
splitter while under the influence of alcohol, drugs,
or medication.
NEVER leave the log splitter unattended while the
engine is running.
DO NOT change the splitting position with the engine
running. Contact with the muffler can cause serious
burns.
Always make sure the beam is in the locked position.
DO NOT let the beam drop as it could crush fingers
or cause damage to the log splitter.
Starting the Engine
1. Make certain the log splitter is on a flat, level
surface.
2. Using your fingers, open the hydraulic vent screw by
turning it counter clockwise approximately 2-3 times.
3. Flip engine switch to “ON” position (Item A).
4. Rotate the fuel valve to the “ON” position (Item B).
5. Move the throttle lever (Item C) to the “Fast”
position.
6. Move the choke lever (Item D) to the “Choke”
position.
7. Pull the starter cord slowly until resistance is felt and
then pull rapidly. SEE NOTE BELOW.
NOTE
Keep choke lever in “Choke” position for 2 pulls
of the recoil starter. After second pull, move choke
lever to the “Run” position for up to the next 3
pulls of the recoil starter. Too much choke leads to
spark plug fouling/engine flooding due to the lack of
incoming air. This will cause the engine not to start.
15
REV 93520-20130425
Starting the Engine Cont’d.
8. As engine warms up, move the choke lever (Item D)
to “Run.”
B
C
A
D
NOTE
If the engine starts but does not run make certain
that the log splitter is on a flat, level surface. The
engine is equipped with a low oil sensor that will
prevent the engine from running when the oil level
falls below a critical threshold.
The hydraulic oil needs to be above 10° F (-12° C)
before starting the engine. Cold hydraulic oil can
damage the hydraulic pump.
If outdoor air temperature is below 32° F (0° C)
allow the log splitter to warm up by extending and
returning the wedge several times before splitting
wood.
Stopping the Engine
1. Turn the fuel knob to the “Off” position. (B)
2. Let the engine run until fuel starvation has stopped
the engine. This usually takes a few minutes.
3. Turn the engine switch to the “Off” position. (A)
4. Using your fingers, tighten the hydraulic vent screw
by turning it clockwise approximately 2-3 times.
Important: Always ensure that the Fuel Valve and the
Engine Switch are in the “OFF” position when the
engine is not in use.
NOTE
If the engine will not be used for a period of two (2)
weeks or longer, please see the Storage section for
proper engine and fuel storage.
93520 ENGLISH
Log Splitter Operation
1. ALWAYS wear ear and eye protection, protective clothing
and safety gear.
Operation
Log Splitter Operation Cont’d.
NOTE
If a log gets stuck, embedded or will not split
completely, push the control handle in the reverse
direction and allow the splitter to strip the log from
the wedge.
ALWAYS keep hands clear of the log and wedge
while it is retracting.
NOTE
2. Block tires and ensure support leg is secure to
prevent unintended movement of the log splitter
during operation.
3. Set log splitter in either the horizontal or vertical
position.
The cylinder stroke is designed so the wedge stops
approximately 3.81 cm (1.5 in.) from the end plate.
NOTE
HORIZONTAL position is used for lighter logs that
can easily be loaded onto the beam.
VERTICAL position is used for light logs as well as
heavy logs that are difficult to load onto the beam.
Back injury can result from lifting logs onto the log
splitter if proper lifting techniques are not used.
4. Load a log onto the beam against the end plate
(MAX LOG LENGTH – 24” [61 cm]).
5. Make sure all limbs are clear of crush zones.
6. Push the control valve handle forward (towards the
end plate) to split the log.
7. Push the auto control valve handle backward to
return the wedge to its original position.
8. Clear the split wood from the work zone.
CAUTION
Do not hold auto control valve in return position. It
will damage the stop block or beam.
NOTE
It is normal for the hydraulic fluid to become foamy
or frothy during operation.
REV 93520-20130425
16
ENGLISH 93520
Operation
Operation at High Altitude
The density of air at high altitude is lower than at sea
level. Engine power is reduced as the air mass and
air-fuel ratio decrease. Engine power and output will
be reduced approximately 3½% for every 1000 feet of
elevation above sea level. This is a natural trend and
cannot be changed by adjusting the engine. At high
altitudes increased exhaust emissions can also result
due to the increased enrichment of the air fuel ratio.
Other high altitude issues can include hard starting,
increased fuel consumption and spark plug fouling.
To alleviate high altitude issues other than the natural
power loss, Champion Power Equipment can provide a
high altitude carburetor main jet. The alternative main
jet and installation instructions can be obtained by
contacting Customer Support. Installation instructions
are also available in the Technical Bulletin area of the
Champion Power Equipment internet site.
The part number and recommended minimum altitude
for the application of the high altitude carburetor main
jet is listed in the table below.
In order to select the correct high altitude main jet
it is necessary to identify the carburetor model. For
this purpose, a code is stamped on the side of the
carburetor. Select the correct main jet part number
corresponding to the carburetor code found on your
particular carburetor.
Carburetor
Code
P23-1-Z
P23-1-R
Main Jet
Part Number
Standard
46.131017.01.Z
Altitude
46.131017.01.01.Z
Standard
46.131017.01.R
Altitude
46.131017.01.01.R
Altitude
5000 Feet
(1524 Meters)
WARNING
Operation using the alternative main jet at
elevations lower than the recommended minimum
altitude can damage the engine. For operation at
lower elevations, the standard main jet must be
used. Operating the engine with the wrong engine
configuration at a given altitude may increase
its emissions and decrease fuel efficiency and
performance.
17
REV 93520-20130425
93520 ENGLISH
The owner/operator is responsible for all periodic
maintenance.
WARNING
Never operate a damaged or defective log splitter.
Maintenance and Storage
Spark Plugs
1. Remove the spark plug cable from the spark plug.
2. Inspect the electrode on the plug. It must be clean
and not worn to produce the spark required for
ignition.
3. Make certain the spark plug gap is 0.7 - 0.8 mm
(0.028 - 0.031 in.).
WARNING
Improper maintenance will void your warranty.
0.7 - 0.8 mm
0.028 - 0.031 in.
NOTE
For service or parts assistance, contact our help line
at 1-877-338-0999.
Engine Maintenance
4. Refer to the spark plug recommendation chart when
replacing the plug.
5. Carefully thread the plug into the engine.
6. Use the spark plug tool to firmly install the plug.
7. Attach the spark plug wire to the plug.
To prevent accidental starting, remove and ground spark
plug wire before performing any service.
Air Filter
Complete all scheduled maintenance in a timely manner.
Correct any issue before operating the log splitter.
Oil
Change oil when the engine is warm. Refer to the oil
specification to select the proper grade of oil for your
operating environment.
1. Remove the oil drain plug with a 15 mm socket and
extension.
2. Allow the oil to drain completely.
3. Replace the drain plug.
4. Remove oil fill cap/dipstick to add oil.
5. Add up to 1.16 qt. (1.1 L) of oil and replace oil fill
cap/dipstick. DO NOT OVERFILL.
6. Dispose of used oil at an approved waste
management facility.
NOTE
Once oil has been added, a visual check should show
oil about 1-2 threads from running out of the fill hole.
If using the dipstick to check oil level, DO NOT screw
in the dipstick while checking.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Unscrew wing nut to remove the air filter cover.
Unscrew wing nut to remove the air filter.
Separate the foam element and the paper element.
Tap the paper filter element to remove dirt and
debris. Use compressed air (25 PSI) to clear debris.
For the foam element: Wash in liquid detergent and
water. Squeeze thoroughly dry in a clean cloth.
Saturate in clean engine oil.
Squeeze in a clean, absorbent cloth to remove all
excess oil.
Reassemble the two elements and reattach. Tighten
wing nut.
Reattach the air filter cover and snap in place.
Log Splitter Maintenance
Make certain that the log splitter is kept clean and stored
properly. Only operate the unit on a flat, level surface in
a clean, dry operating environment. DO NOT expose the
unit to extreme conditions, excessive dust, dirt, moisture
or corrosive vapors.
Inspect all air vents and cooling slots to ensure that they
are clean and unobstructed.
Check and tighten all bolts and nuts before operating the
log splitter.
Be sure to confirm all hose connections and hose clamps
are tight before each use. It is possible for connections
to vibrate loose over time.
REV 93520-20130425
18
ENGLISH 93520
Maintenance and Storage
Changing the Hydraulic Oil and Oil Filter
NOTE
Changing the Hydraulic Oil and Oil Filter Cont’d.
B
Install a new hydraulic oil filter each time the
hydraulic oil is changed
1. Begin with the cylinder retracted and the engine
“OFF.”
2. Turn the fuel valve “OFF.”
3. Release any stored pressure by moving the valve
lever forward and backward several times.
4. Place a container under the hydraulic tank. Make
sure it is large enough to hold the contents of the
tank.
5. To drain the oil, unscrew and remove the tank drain
plug on the bottom of the hydraulic tank.
a. Unscrew and remove the hydraulic oil filter.
b. Drain any oil in the filter into the container.
6. Allow oil to completely drain from the tank into the
container.
7. Install a new hydraulic oil filter. (A)
a. Turn the filter counter-clockwise to remove it. A
strap wrench may be used.
b. Lubricate the gasket of the new filter with a thin
film of clean oil.
c. Screw the new filter on clockwise. Tighten 3/4 1 turn after the gasket makes contact.
A
C
9. Unscrew and remove the tank fill plug, on top of the
tank. Using a funnel add approximately 7 gal.
(26.5 L) of hydraulic oil to the tank. Wipe up any
spilled oil. (B)
10.Turn the fuel valve on, and start the engine. Purge
the air from the system by extending and retracting
the wedge several times until the motion is smooth.
11.Check the hydraulic oil level using the sight glass.
Add 1 to 2 gal. (3.79 to 7.6 L) of hydraulic oil, so
the oil level is visible in the sight glass. (C)
12.Dispose of used oil at approved recycling locations.
WARNING
Always shut off the engine, disconnect the spark
plug, and relieve system pressure before cleaning,
adjusting, or repairing the splitter. Relieve system
pressure by moving split control lever back and
forth several times
NOTE
Change the hydraulic oil filter after the first 50 hours
of use. Then every 100 hours or seasonally.
NOTE
The drain plug is sealed with Teflon tape. Add 2-3
wraps of new Teflon tape as needed when replacing
the drain plug to prevent oil leak
8. Reinsert and screw in the tank drain plug. Tighten,
but do not over tighten.
19
REV 93520-20130425
NOTE
Replacement filters can be purchased from
Champion Power Equipment by calling
1-877-338-0999. Wix #51391 or Fram PH3682
can also be used if needed.
93520 ENGLISH
Maintenance and Storage
Cleaning
Storage
Clear the debris from the beam, wedge and end plate.
Use a damp cloth to clean exterior surfaces of the engine
and log splitter.
Use a soft bristle brush to remove excess dirt and oil. Use
an air compressor (25 PSI) to clear dirt and small debris.
Wipe all metal parts with an oily rag to help prevent rust
and corrosion.
Refer to the Maintenance section for proper cleaning
instructions.
CAUTION
DO NOT use a garden hose to clean the engine or
log splitter.
Water can contaminate the fuel system and can
enter the engine through the cooling slots and
damage the engine.
Maintenance Schedule
Follow the service intervals indicated in the schedule
below. Service your log splitter more frequently when
operating in adverse conditions. Contact our help line at
1-877-338-0999 to locate the nearest Champion Power
Equipment authorized service dealer for your log splitter
or engine maintenance needs.
Every 8 hours or daily
Check engine and hydraulic oil levels
Clean around air intake and muffler
First 5 Hours
Change engine oil
Every 50 hours or every season
Clean air filter
Change engine oil if operating under heavy load or in
hot environments
Every 100 hours or every season
Change engine oil
Clean/Adjust spark plug
Check/Adjust valve clearance*
Clean fuel tank and filter*
Change hydraulic oil
Log Splitter Storage
1. The log splitter needs to be cool for at least 5
minutes before storing.
2. Clean the log splitter before storage according to the
Maintenance section.
3. Retract the wedge to protect the rod from corrosion.
4. Wipe the beam and wedge with an oily rag to
prevent rust and corrosion.
Engine Stored for Less than 30 Days
1.
2.
3.
4.
Allow the engine to cool completely before storage.
Clean engine according to the Maintenance section.
To extend the fuel storage life add fuel stabilizer.
Turn the fuel valve to the off position.
Engines Stored for Over 30 Days
1. Run the engine with the fuel valve in the “Off”
position until the engine stops.
2. The engine needs to cool completely before storage.
3. Clean engine according to the Maintenance section.
4. Drain all fuel completely from the fuel line and
carburetor to prevent gum from forming.
5. Add a fuel stabilizer into the fuel tank.
6. Change the oil.
7. The fuel valve needs to be in the off position.
8. Remove the spark plug and pour about 1⁄2 ounce
of oil into the cylinder. Crank the engine slowly to
distribute the oil and lubricate the cylinder.
9. Reattach the spark plug.
WARNING
Never store the log splitter inside next to appliances
where there is a source of heat or open flame, spark
or pilot light because they can ignite gasoline vapors.
DO NOT store a log splitter near fertilizer or any
corrosive material.
Even with an empty gas tank, gasoline vapors could
ignite.
Change hydraulic oil filter
Every 250 hours
Clean combustion chamber*
Every year
Inspect wheel bearings and repack bearing grease as needed.
Every 3 years
Replace fuel line
*To be performed by knowledgeable, experienced owners or
Champion Power Equipment certified dealers.
REV 93520-20130425
20
ENGLISH 93520
TROUBLESHOOTING
Problem
Cause
Solution
Engine will not start
No fuel
Add fuel
Faulty spark plug
Replace spark plug
Unit loaded during start up
Remove load from unit
Low oil level
Fill crankcase to the proper level
Engine will not start;
Engine starts but runs roughly
Engine shuts down during operation
Place log splitter on a flat, level surface
Choke in the wrong position
Adjust choke
Spark plug wire loose
Attach wire to spark plug
Out of fuel
Fill fuel tank
Low oil level
Fill crankcase to the proper level. Place
log splitter on a flat, level surface
Engine cannot supply enough power or Insufficient ventilation
overheating
Check for air restriction. Move to a
well ventilated area
Wedge movement is slow or erratic
Air in the hydraulic oil system
Purge air by extending and retracting
the wedge several times until motion
is smooth
Debris lodged in beam guides
Clear debris from beam
Low hydraulic oil
Check oil level and add as needed
Oil leak from hose connection
Loose hose clamp or hydraulic fitting
Tighten hose clamp or hydraulic fitting
Oil leak from cylinder
Faulty cylinder rod seal
Contact Customer Service
Scored or bent cylinder rod
Contact Customer Service
Loose hydraulic fitting
Tighten hydraulic fitting
Faulty combination washer seal on
cylinder hydraulic fitting
Contact Customer Service
Faulty control valve
Contact Customer Service
Faulty hydraulic pump
Contact Customer Service
Low hydraulic oil
Check oil level and add as needed
Low hydraulic oil
Check oil level and add as needed
Faulty control valve
Contact Customer Service
Under-inflated tires
Inflate tires to proper pressure. Refer
to tire sidewall
Wedge will not extend or retract
Wedge does not Auto-Return
Excessive bouncing while towing
For further technical support:
Technical Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
[email protected]
21
REV 93520-20130425
93520 ENGLISH
Specifications
Log Splitter Specifications
Hydraulic Oil System
––
––
––
––
––
––
––
––
––
––
––
––
––
––
Oil capacity is 9 gallons (34 L).
Use types 10W AW32, ASLE H-150, ISO32 or universal
hydraulic fluid.
Spin-On Filter – 15GPM, 10 Micron, ¾-16 Thread.
Ram Force. . . . . . . . . . . . . . . . . . . . . . . . . 35 Ton
Cycle Time. . . . . . . . . . . . . . . . . . . . . . 16 seconds
Hydraulic Tank Capacity. . . . . . . . . . 7 gal. (26.5 L)
Max Log Length . . . . . . . . . . . . . . . 24-in. (61 cm)
Max Log Weight . . . . . . . . . . . . . . . 100 lb. (45 kg)
Coupler Ball Size. . . . . . . . . . . . . . . . . 2-in. (5 cm)
Tire Size . . . . . . . . . . . . . . . . . . . 16-in. (40.6 cm)
Max towing speed. . . . . . . . . . . . 45 MPH (72 KPH)
Engine. . . . . . . . . . . . . . . . . 338 cc, OHV, 4 stroke
Cylinder size. . . . . 5 in. x 23 in. (12.7 cm x 58.4 cm)
Cylinder rod size. . . . . . . . . . . . . 1.84 in. (4.5 cm)
Gear Pump. . . . . . . . . . . . . . . . . . . . . . . . 2-stage
Max pressure. . . . . . . . . . . . . . . . . . . . . 3500 psi
Max flow capacity. . . . . . . . . . . . . . . . . . . 13 GPM
–– Control Valve . . . . . . . . . . . . . . Detent (auto-return)
Overall Dimensions
––
––
––
––
––
Gross Weight . . . . . . . . . . . . . . . 617.3 lb. (280 kg)
Net Weight. . . . . . . . . . . . . . . . . 562.2 lb. (255 kg)
Height. . . . . . . . . . . . . . . . . . . . 47 in. (119.4 cm)
Width . . . . . . . . . . . . . . . . . . . . 41 in. (104.1 cm)
Length. . . . . . . . . . . . . . . . . . . .86.2 in. (219 cm)
NOTE
When temperature is below 32º F (0ºC) use
universal tractor/transmission fluid.
Fuel
Fuel capacity is 1.64 gal. (6.2 L). Use regular unleaded
gasoline with a minimum octane rating of 85 and an
ethanol content of less than 10% by volume.
Oil
Use 10W-30 automotive oil.
Oil capacity is 1.16 qt. (1.1 L).
DO NOT OVERFILL.
Please reference the following chart for recommended
oil types for use in the log splitter.
Engine Specifications
––
––
––
––
Model. . . . . . . . . . . . . . . . . . . . . . . . YF182F-001
Displacement. . . . . . . . . . . . . . . . . . . . . . . 338 cc
Type. . . . . . . . . . . . . . . . . . . . . . . . 4-Stroke OHV
Start Type . . . . . . . . . . . . . . . . . . . . . . . . . Recoil
Spark Plugs
OEM spark plug: NHSP F6RTC
Replacement spark plug: NGK BPR6ES or equivalent
Make certain the spark plug gap is 0.7 - 0.8 mm or
(0.028 - 0.031 in.).
Maintenance Valve Clearance
–– Intake: 0.13 – 0.17 mm (0.005 – 0.007 in.)
–– Exhaust: 0.18 – 0.22 mm (0.007 – 0.009 in.)
Note: Tech bulletin regarding the valve adjustment
procedure is on www.championpowerequipment.com.
An Important Message About Temperature
Your Champion Power Equipment product is designed
and rated for continuous operation at ambient
temperatures up to 40°C (104°F). When your product is
needed your product may be operated at temperatures
ranging from -15°C (5°F) to 50°C (122°F) for short
periods. If the product is exposed to temperatures
outside this range during storage, it should be brought
back within this range before operation. In any event,
the product must always be operated outdoors, in a
well-ventilated area and away from doors, windows and
other vents.
REV 93520-20130425
22
23
82
81
REV 93520-20130425
78
26
80
27
76
28 29
77
75
79
28
78 69
27 48
86
74
(D)
83
68
(C)
2 3
TO(D)
1
85
30
67 11
71
41
66
TO(C) 73
72
84
4
11
12
13
14
5 15
(A)
6 7
65
9
64
70
32
49
24
25
18
TO(B)
42
2
60
59
3
44
35
TO(E)
(E)
43
50
58
52 2
45 23 22
37 38 39 40
34 36
33
63 62 61
(F)
31
TO(A)
21
42
20
19
(B)
10
22 23 24
18
16
17
8
51
57
31
53
TO(F)
47 28 27 48
46
54
55
56
Specifications
ENGLISH 93520
Parts Diagram
93520 ENGLISH
Parts List
#
Part Number
Description
1
PMJ35-02
Beam
Qty
#
Part Number
Description
Qty
1
44
GB/T 77-2000
Screw M6×10
1
45
ASME B18.2.1 1996
Bolt 5/16"-24×1"
4
46
YF182F-001
Engine
1
2
GB/T 889.1-2000
Lock Nut M12
8
3
GB/T 95-2000
Washer 12
7
4
PMJ22J-04-00
Wedge Slide
1
5
PMJ22J-20
Bolt
1
6
PMJ22J-12
Control Valve
1
7
GB/T 818-2000
Bolt M8×12
2
8
GB/T 859-1987
Washer 8
2
9
PMJ22J-19
Plate
1
10
PMJ22G-51
Filter Housing "IN" Connection
1
11
PMJ22G-49
Filter Housing "OUT" Connection
2
12
JB/T 8870-1999
Clamp d25
2
13
PMJ22G-25
Valve Joiner
1
14
GB3452.1-92
"O" Ring 14×2.65
1
15
PMJ22G-22
Front Cover Connection
1
16
PMJ22G-24
Valve Joiner
1
17
GB 982-1977
Combination Washer 14
4
18
PMJ22G-23
Bolt Connection
2
19
PMJ22J-13
Hydraulic Hose(Valve-Cylinder)
1
20
PMJ35-08-00
Cylinder
1
2
21
PMJ30-03
Cylinder Fixing Plate
22
GB/T 95-2000
Washer 8
12
23
GB/T 93-1987
Lock Washer 8
12
24
GB/T 5783-2000
Bolt M8x20
12
25
PMJ22J-18
Hydraulic Hose(Valve-Pump)
1
26
GB/T 5781-2000
Bolt M10x15
8
27
GB/T 93-1987
Lock Washer 10
16
28
GB/T 95-2000
Washer 10
16
29
PMJ30F-01
Log Catcher
2
30
PMJ22J-15
Pin
1
31
PMJ22G-30
R Pin
2
32
PMJ22G-15
Hydraulic Hose(Valve-Oil Tank)
1
33
GB/T 3452.1-92
"O" Ring 10×2.65
1
34
PMJ22G-21
Outlet Connector Of Pump
1
35
GB/T 1096-1979
Flat Key
1
36
PMJ22G-26
Gear Pump Connector
1
37
PMJ30-23
Gear Pump Stand
1
38
PMJ30-28
Engine Connector
1
39
PMJ30-29
Engine Bushing
1
40
PMJ30-32
Key
1
41
GB/T 5782-2000
Bolt M12x70
1
42
JB/T 8870-1999
Clamp d40
2
43
PMJ35-10
Gear Pump
1
47
GB/T 5780-2000
Bolt M10x45
4
48
GB/T 41-2000
Nut M10
8
49
PMJ30-06
Base Tube
1
50
GB/T 5782-2000
Bolt M12×65
2
51
PMJ22J-01-00
Base Connector
1
52
PMJ22J-10
Pin
1
53
GB/T 97.2-1985
Washer 12
4
54
GB/T 5782-2000
Bolt M12×90
1
55
GB/T 5782-2000
Bolt M12×80
2
56
PMJ22G-40
2" Coupler
1
57
PMJ22G-41
Safety Chain With Hook
2
58
PMJ22J-07-00
Front Support Leg
1
59
PMJ30-17
Oil Pipe
1
60
GB/T 70.1-2000
Screw M5×20
6
61
GB/T 93-1987
Lock Washer 5
6
62
GB/T 95-1985
Washer 5
6
63
PMJ22G-07-00
Filter Fix Plate
1
64
PMJ22G-44
Filter
1
65
GB/T 3452.1-92
"O" Ring 80×3.55
1
66
PMJ22G-52
Auto Filter
1
67
PMJ22G-50
Auto Filter Base
1
68
PMJ22G-19
Oil Plug
1
69
PMJ30-01
Oil Tank
1
70
PMJ22G-35-00
Right Fender
1
71
GB/T 5782-2000
Bolt M12×85
2
72
PMJ22G-12
Hinge Pin
1
73
PMJ22G-18
Screw NPT1"
1
74
GJY12-3
R Pin
1
75
GB/T 5781-2000
Bolt M10x30
4
76
PMJ22G-34-00
Left Fender
1
77
GB/T 91-2000
Cotter Pin 4×32
2
78
PMJ22J-05-01
Cased Seal
2
79
L44634 LYC DS
Tapered Bearing
4
80
PMJ22J-05-03
Wheel
2
81
GB/T 9459-1988
Slotted Nut M20x1.5
2
82
PMJ22J-05-02
Axle Cap
2
83
PMJ22G-38
Big Tension Spring
1
84
GB/T 798-1988
Swing Bolt M8x28
1
85
GB/T 6170-2000
Nut M8
1
86
GB 1160.2-89
Oil Scale
1
REV 93520-20130425
24
25
REV 93520-20130425
2
117
13
1
116
115
3
120
121
122
123
92
124
125
114
119 118
113
12
4
13
91
23
112
5
24
111
25
128
6
26
127
7
27
110
8
28
126
9
29
30
11
108
10
109
31
107
130
13
32
14
129
90
89
15
13
106
105
104
100
101
102
103
16
88
17
33
64
87
91
92
18
86
65
85
99
66
19
34
67
68
20
35
69
70
36
71
21
72
13
73
74
37
75
22
93
95
96
97
98
31
76
94
78
38
77
79
47
39
80
81
48
82
40
49
22
51
84
50
83
41
52
53
54
46
131
55
56
45
132
13
44
57
43
146
58
42
133
59
134
107
60
135
61
134
62
136
63
137
147
89
145
138
139
140
141
142
143
144
Specifications
ENGLISH 93520
Engine Parts Diagram
93520 ENGLISH
Engine Parts List
#
Part Number
Description
Qty
#
Part Number
Description
1
21.061300.00
Recoil Handle
1
76
46.040004.00
Guide Plate ,Push Rod
1
2
1.5789.0608
Flange bolt M6×8
3
77
46.040016.00
Shaft, Rocker Arm
1
3
46.061100.00.2
Recoil Starter Cover
1
78
46.040201.00
Retainer, Rocker Arm
1
4
45.060005.00
Recoil Starter Spring
1
79
46.040009.00
Rocker Arm, Intake Valve
1
5
45.061102.00
Recoil Starter Reel
1
80
46.040018.00
Rocker Arm, Exhaust Valve
1
6
2.10.003
Rope(Ø5×1550)
1
81
1.97.1.06
Washer 6
2
7
45.060003.00
Spring,Ratchet
2
82
22.040012.00
Screw, Valve Adjustment
2
8
45.060002.00
Starter Ratchet(Iron)
2
83
1.6177.1.06
Flange Nut M6
2
9
45.060009.00
Spring,Ratchet Guide
1
84
21.040021.00
Net,Lock
2
10
45.060007.00
Ratchet Guide
1
85
2.01.007
Stud Bolt(M6×M8×130)
2
11
45.060008.00
Screw, Ratchet Guide
1
86
46.130002.20
Gasket, Insulator(No Asbestos)
1
12
46.061000.00
Recoil Assembly
1
87
45.130001.01
Insulator, Carburetor
1
13
1.5789.0612
Flange bolt M6×12
13
88
46.130003.00
Gasket ,Carburetor(No Asbestos)
1
14
2.05.003
Clamp(Ø11.5×10)
1
89
46.131000.01
Carburetor
1
15
46.080100.00.48
Fan Cover
1
90
45.130004.00
Gasket, Air Cleaner
1
16
2.02.007
Nut(M16×1.5)
1
91
2.06.007
clip(Ø8×b6)
3
17
1.5789.0629
Flange bolt 6×29
2
92
1.6177.06
Flange Nut (M6)
3
18
45.060001.00
Pulley, Starter
1
93
46.091100.01
Base, Air Cleaner
1
19
46.123000.03
Ignition Coil
1
94
1.5789.0633
Flange bolt M6×33
1
20
45.080001.00
Cooling Fan
1
95
46.091003.02
Element, Air Cleaner
1
21
46.120100.03
Flywheel
1
96
46.091102.02
Supporter, air cleaner
2
22
2.11.007
Oil Seal(Ø35×Ø52×8)
2
97
46.091200.02
Cover, Air Cleaner
1
23
23.120700.02
Change wire flameout
1
98
46.091600.01
Screw cap, Air clean Cover
2
24
21.120400.00
Diode Assembly
1
99
46.091000.02
Air Cleaner Assembly
1
25
45.030032.00
Sheath, Wire
1
100
46.070013.00
Pipe, Air Cleaner
1
26
2.08.039
Bolt, Drain(M12×1.5×15)
2
101
46.070014.00
Pipe
1
27
2.03.023
Washer(Ø12.5×Ø20×2)
2
102
2.12.001
Buffer(Ø7.5×7.5)
1
28
46.030100.00
Crankcase
1
103
46.070700.00
Carbon Canister
1
29
45.127000.01
Oil Level Sensor
1
104
24.070100.02
Fuel tank cap
1
30
1.5789.0615
Flange bolt 6×15
2
105
46.070300.00
Fuel filter componet
1
31
1.276.6202
Bearing 6202
2
106
2.06.006
Clamp(Ø7×Ø1)
3
32
45.050006.00
Weight Balancer
1
107
1.6187.1.08
Nut M8
5
33
45.050100.09
Crankshaft(U)
1
108
111.070300.01
Fuel filter component
1
34
46.030008.00
Gasket, Crankcase Cover
1
109
2.06.018
clip(Ø10.5×b8)
1
35
2.04.001
Dowel Pin(Ø9×14)
2
110
46.071000.01
Fuel tank
1
36
46.080600.00
Air Guide, Right Side
1
111
1.5789.0832
Flange bolt 8×32
2
37
1.276.6207
Bearing 6207
1
112
46.070011.00
Pipe, Fuel
1
38
46.031000.01.48
Oil Dipstick Assembly
1
113
24.070400.00
Fuel valve
1
39
45.030007.01
Cover, Crankcase
1
114
1.16674.0512.2
Flange bolt M5×12
1
40
22.031000.01.48
Oil filler cap
1
115
46.070011.01
Pipe, Fuel
1
41
1.5789.0840.0.8
Flange bolt 8×40
7
116
46.070010.00
Fuel tank veil
1
42
2.03.021.1
Washer(Ø6.4×Ø13×1)
1
117
5.1010.002
43
45.110013.00
Shaft,Governor Gear
1
118
24.070001.00
Fuel valve knob
1
44
45.110100.00
Gear, Governor
1
119
1.818.0412
bolt M4X12
1
45
21.110011.00
Clip, Governor Gear
1
120
45.110001.00
Shaft, Governor Arm
1
46
45.110012.00
Bushing, Governor Gear
1
121
2.03.019
Washer(Ø8.2×Ø17×0.8)
1
47
45.050200.00
Connecting Rod
1
122
2.11.006
Oil Seal(Ø7×Ø14×5)
1
48
46.050005.01
Piston
1
123
45.110008.00
Pin, Shaft
1
49
2.09.004
Circlip(Ø21×Ø1)
2
124
45.110003.00
Arm, Governor
1
50
45.050003.00
Wrist Pin
1
125
2.08.040
Bolt,Governor Arm(M6×21)
1
51
46.050303.01
Ring, Oil
1
126
45.110007.00
Spring, Governor
1
52
46.050302.01
Ring, Second Piston
1
127
45.110005.00
Spring, Throttle Return
1
53
46.050301.01
Ring,First Piston
1
128
45.110006.00
Rod Governor
1
54
2.04.004
Dowel Pin(Ø12×20)
2
129
46.080300.00
Air Guide, Upper
1
55
46.030009.00
Gasket, Cylinder Head(no asbestos)
1
130
24.111008.01
Sheath,Grip
1
56
46.080400.00
Air Guide, Lower
1
131
2.01.005
Stud Bolt(M8×49)
2
57
46.010100.00
Cylinder Head
1
132
46.100001.07
58
2.15.002(F6RTC)
Spark Plug(F6RTC)
1
133
46.101001.05
Exhaust pipe
1
59
2.08.014
Flange bolt 10×80
4
134
1.848.08
Washer Ø8
7
60
46.020002.00
Gasket, Cylinder Head Cover
1
135
1.859.08
Spring washer Ø8
5
61
46.021000.00
Cylinder Head Cover (CPE)
1
136
1.93.08
Spring washer Ø8
2
62
45.020001.02
Breather Tube
1
137
1.6175.08
Nut M8
2
63
45.020100.00
Bolt, Cylinder Head Cover
1
138
46.101002.05
Washer, Muffler
1
64
46.041000.00
Camshaft (EPA)
1
139
46.101100.05
Muffler component
1
65
45.040013.00
Lifter, Valve
2
140
1.16674.0510
Flange bolt M5×10
5
66
45.040002.00
Valve, Intake
1
141
46.101202.05
Muffler Protector
1
67
45.040006.00
Valve, Exhaust
1
142
46.101300.05
Spark Arrester
1
68
46.040005.00
Push Rod
2
143
1.818.046
screw M4×6
4
69
45.040015.00
Retainer, Valve Spring (Down)
2
144
1.848.05
Washer Ø5
5
70
45.040017.00
Oil Seal, Valve
2
145
1.859.05
Spring washer Ø5
5
71
45.040003.00
Spring, Valve
2
146
46.101000.05
Muffler Assembly
1
72
23.040010.00
Bolt, Rocker Arm
2
46.131017.01
Standard Main Jet
1
73
45.040001.00
Retainer, Intake Valve Spring(Up)
1
46.131017.01.01
Altitude Main Jet
/
74
45.040007.00
Retainer, Exhaust Valve Spring(Up)
1
75
45.040008.00
Rotator, Exhaust Valve
1
147
Qty
Flameout Switch
Gasket,Exhaust pipe
1
1
REV 93520-20130425
26
ENGLISH 93520
Warranty
WARRANTY
CHAMPION POWER EQUIPMENT
1 YEAR LIMITED WARRANTY
Warranty Qualifications
Champion Power Equipment (CPE) will register this
warranty upon receipt of your Warranty Registration Card
and a copy of your sales receipt from one of CPE’s retail
locations as proof of purchase.
Please submit your warranty registration and your proof
of purchase within ten (10) days of the date of purchase.
Repair/Replacement Warranty
CPE warrants to the original purchaser that the
mechanical and electrical components will be free of
defects in material and workmanship for a period of one
(1) year from the original date of purchase (90 days for
commercial & industrial use). Transportation charges on
product submitted for repair or replacement under this
warranty are the sole responsibility of the purchaser.
This warranty only applies to the original purchaser and
is not transferable.
Do Not Return The Unit To The Place Of Purchase
Contact CPE’s Technical Service and CPE will
troubleshoot any issue via phone or e-mail. If the
problem is not corrected by this method, CPE will, at its
option, authorize evaluation, repair or replacement of the
defective part or component at a CPE Service Center.
CPE will provide you with a case number for warranty
service. Please keep it for future reference. Repairs
or replacements without prior authorization, or at an
unauthorized repair facility, will not be covered by this
warranty.
Warranty Exclusions
This warranty does not cover the following repairs and
equipment:
Normal Wear
Log Splitter needs periodic parts and service to perform
well. This warranty does not cover repair when normal
use has exhausted the life of a part or the equipment as
a whole.
Installation, Use and Maintenance
This warranty will not apply to parts and/or labor if
this log splitter is deemed to have been misused,
neglected, involved in an accident, abused, loaded
beyond its limits, modified, and installed improperly.
Normal maintenance such as spark plugs, air filters,
adjustments, fuel system cleaning and obstruction due
to buildup is not covered by this warranty.
27
REV 93520-20130425
Other Exclusions
This warranty excludes:
–– Cosmetic defects such as paint, decals, etc.
–– Wear items such as filter elements, o-rings, etc.
–– Accessory parts such as starting batteries, and
storage covers.
–– Failures to due acts of God and other force majeure
events beyond the manufacturer’s control.
–– Problems caused by parts that are not original
Champion Power Equipment parts.
Limits of Implied Warranty and Consequential Damage
Champion Power Equipment disclaims any obligation to
cover any loss of time, use of this product, freight, or
any incidental or consequential claim by anyone from
using this log splitter. THIS WARRANTY IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
A unit provided as an exchange will be subject to the
warranty of the original unit. The length of the warranty
governing the exchanged unit will remain calculated by
reference to the purchase date of the original unit.
This warranty gives you certain legal rights which may
change from state to state. Your state may also have
other rights you may be entitled to that are not listed
within this warranty.
Contact Information
Address
Champion Power Equipment, Inc.
Customer Service
10006 Santa Fe Springs Rd.
Santa Fe Springs, CA 90670
www.championpowerequipment.com
Customer Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
[email protected]
Fax no.: 1-562-236-9429
Technical Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
[email protected]
24/7 Tech Support: 1-562-204-1188
Champion Power Equipment, Inc. (CPE),
The United States Environment Protection Agency (U.S. EPA.) and the California Air Resources Board (CARB)
Emission Control System Warranty
Your Champion Power Equipment (CPE) engine complies with both the U.S. EPA and state of California Air
Resources Board (CARB) emission regulations.
YOUR WARRANTY RIGHTS AND OBLIGATIONS:
The US EPA, California Air Resources Board, and CPE are pleased to explain the Federal and California Emission
Control Systems Warranty on your 2013 small off-road engine and engine powered equipment. In California, new,
small off-road engines and new equipment that use small off-road engines must be designed, built and equipped to
meet the State’s stringent anti smog standards. In the other states, new engines and equipment must be designed,
built and equipped, at the time of sale, to meet U.S. EPA regulations for small non-road engines. CPE warrants the
emission control system on your small off-road engine and equipment for the period of time listed below, provided
there has been no abuse, neglect, unapproved modification, or improper maintenance of your equipment.
Your emission control system may include parts such as the carburetor, fuel-injection system, the ignition system,
catalytic converter and fuel lines. Also included may be hoses, belts, connectors and other emission related
assemblies. Where a warrantable condition exits, CPE will repair your small off-road engine at no cost to you
including diagnosis, parts and labor. For engines less than or equal to 80cc, only the fuel tank and fuel line is
subject to the evaporative emission control warranty requirements of this section.
MANUFACTURER’S EMISSION CONTROL SYSTEM WARRANTY COVERAGE:
This emission control system is warranted for two years, subject to provisions set forth below. If, during the
warranty period, emission related part on your engine is defective in materials or workmanship, the part will be
repaired or replaced by CPE.
OWNER WARRANTY RESPONSIBILITIES:
As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in
your Owner’s Manual. CPE recommends that you retain all your receipts covering maintenance on your small offroad engine, but CPE cannot deny warranty solely for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.
As the small off-road engine owner, you should however be aware that CPE may deny you warranty coverage if
your small, off-road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved
modifications.
You are responsible for presenting your small off-road engine to an Authorized CPE service outlet or alternate
service outlet as described in (3)(f.) below, CPE dealer or CPE, Santa Fe Springs, Ca. as soon as a problem exists.
The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact:
Champion Power Equipment, Inc.
Customer Service
10006 Santa Fe Springs Road
Santa Fe Springs, CA 90670
1-877-338-0999
[email protected]
EMISSION CONTROL SYSTEM WARRANTY
The following are specific provisions relative to your Emission Control System (ECS) Warranty Coverage.
1. APPLICABILITY: This warranty shall apply to 1995 and later model year California small off-road engines (for
other states, 1997 and later model year engines). The ECS Warranty Period shall begin on the date the new engine
or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months
thereafter.
2. GENERAL EMISSIONS WARRANTY COVERAGE
CPE warrants to the original, end-use purchaser of the new engine or equipment and to each subsequent
purchaser that each of its small off-road engines is:
a. Designed, built and equipped so as to conform to U.S. EPA emissions standards for spark-ignited
engines at or below 19 kilowatts and all applicable regulations adopted by the California Air Resources Board
and
b. Free from defects in materials and workmanship that cause the failure of a warranted part to be identical
in all material respects to the part as described in the engine manufacturer’s application for certification for a period
of two years.
3. THE WARRANTY ON EMISSION-RELATED PARTS WILL BE INTERPRETED AS FOLLOWS:
a. Any warranted part that is not scheduled for replacement as required maintenance in the Owners
Manual shall be warranted for the ECS Warranty Period. If any such part fails during the ECS Warranty Period, it
shall be repaired or replaced by CPE according to Subsection “d” below. Any such part repaired or replaced under
the ECS Warranty shall be warranted for any remainder of the ECS Warranty Period.
b. Any warranted, emissions-related part which is scheduled only for regular inspection as specified in the
Owners Manual shall be warranted for the ECS Warranty Period. A statement in such written instructions to the
effect of “repair or replace as necessary”, shall not reduce the ECS Warranty Period. Any such part repaired or
replaced under the ECS Warranty shall be warranted for the remainder of the ECS Warranty Period.
c. Any warranted, emissions-related part which is scheduled for replacement as required maintenance in
the Owner’s Manual shall be warranted for the period of time prior to the first scheduled replacement point for that
part. If the part fails prior to the first scheduled replacement, the part shall be repaired or replaced by CPE
according to Subsection “d” below. Any such emissions-related part repaired or replaced under the ECS Warranty,
shall be warranted for the remainder of the ECS Warranty Period prior to the first scheduled replacement point for
such emissions-related part.
d. Repair or replacement of any warranted, emissions-related part under this ECS Warranty shall be
performed at no charge to the owner at a CPE Authorized Service Outlet.
e. The owner shall not be charged for diagnostic labor which leads to the determination that a part covered
by the ECS Warranty is in fact defective, provided that such diagnostic work is performed at a CPE Authorized
Service Outlet.
f. CPE shall pay for covered emissions warranty repairs at non-authorized service outlets under the
following circumstances:
i. The service is required in a population center with a population over 100,000 according to U.S.
Census 2000 without a CPE Authorized Service Outlet AND
ii. The service is required more than 100 miles from a CPE Authorized Service Outlet. The 100 mile
limitation does not apply in the following states: Alaska, Arizona, Colorado, Hawaii, Idaho, Montana, Nebraska,
Nevada, New Mexico, Oregon, Texas, Utah and Wyoming.
g. CPE shall be liable for damages to other original engine components or approved modifications
proximately caused by a failure under warranty of an emission-related part covered by the ECS Warranty.
h. Throughout the ECS Warranty Period, CPE shall maintain a supply of warranted emission-related parts
sufficient to meet the expected demand for such emission-related parts.
i. Any CPE Authorized and approved emission-related replacement part may be used in the performance of
any ECS Warranty maintenance or repair and will be provided without charge to the owner. Such use shall not
reduce CPE’s warranty obligation.
j. Unapproved add-on or modified parts may not be used to modify or repair a CPE engine. Such use voids
this ECS Warranty and shall be sufficient grounds for disallowing an ECS Warranty claim. CPE shall not be liable
hereunder for failures of any warranted parts of a CPE engine caused by the use of such an unapproved add-on or
modified part.
EMISSION-RELATED PARTS INCLUDE THE FOLLOWING: (using those portions of the list applicable to the
engine)
Systems covered by this
warranty
Fuel Metering System
Fuel regulator, Carburetor and internal parts
Air Induction System
Air cleaner, Intake manifold
Ignition System
Spark plug and parts, Magneto ignition system
Exhaust System
Exhaust manifold, catalytic converter
Miscellaneous Parts
Tubing, Fittings, Seals, Gaskets, and Clamps associated with these listed
systems.
Fuel Tank, Fuel Cap, Fuel Line, Fuel Line Fittings, Clamps, Pressure
Relief Valves, Control Valves, Control Solenoids, Electronic Controls,
Vacuum Control Diaphragms, Control Cables, Control Linkages, Purge
Valves, Vapor Hoses, Liquid/Vapor Separator, Carbon Canister, Canister
Mounting Brackets, Carburetor Purge Port Connector
Evaporative Emissions
Parts Description
TO OBTAIN WARRANTY SERVICE:
You must take your CPE engine or the product on which it is installed, along with your warranty registration card or
other proof of original purchase date, at your expense, to any Champion Power Equipment dealer who is
authorized by Champion Power Equipment, Inc. to sell and service that CPE product during his normal business
hours. Alternate service locations defined in Section (3)(f.) above must be approved by CPE prior to service. Claims
for repair or adjustment found to be caused solely by defects in material or workmanship will not be denied because
the engine was not properly maintained and used.
If you have any questions regarding your warranty rights and responsibilities, or to obtain warranty
service, please write or call Customer Service at Champion Power Equipment, Inc.
Champion Power Equipment, Inc.
10006 Santa Fe Springs Road
Santa Fe Springs, CA 90670
1-877-338-0999
Attn.: Customer Service
[email protected]