our catalog

Transcription

our catalog

Knowing
your environment
Monitoring
and data logging
Products
& solutions 2015
Information
to keep you aware
Be in touch at all times
When storing or transporting products that are sensitive to ambient
conditions, the last thing you want are surprises. You’ve put too much time
and energy into your research to find out too late that the power to your
incubator went down and damaged your cultures. The biological samples
in your cryogenic freezer are too valuable to lose because of an unreported
change in storage conditions. Transporting blood is too important to take
any chances with temperature variations. The dangers of not respecting the
cold-chain in food handling are well-known and well-regulated. It is simply
not enough to measure the cost of these types of losses in monetary terms.
Time, opportunity, and safety are also critical factors.
Automated solutions can keep watch for you.
Fast response can change
everything
Anomalies can occur even with the best storage and refrigeration
equipment, cabinets, containers, and incubators. Nobody can prevent
every power outage, freezer compressor failure, or defective thermostat.
Sometimes simply leaving a door open accidently can have dramatic
consequences if left undetected. Part of your job is to expect the unexpected
to address these issues before it’s too late.
In most cases, all you need is to know what’s going on.
Our goal is to protect
your work
Monitoring your environment is part of an overall process that enables you
to concentrate on your field of expertise. At OCEASOFT, we measure our
success by how well we help keep your work going smoothly. You may have
medical emergencies, deadlines, budgets or mission-critical research at stake.
The less you have to think about equipment reliability the better.
Peace-of-mind in your field comes from being prepared.
© 2015 OCEASOFT | www.oceasoft.com | [email protected]
2
Dear Customer –
For well over a decade, OCEASOFT has been proudly serving you
with complete end-to-end systems for monitoring thermal and
ambient conditions in static and mobile environments. Our remote
monitoring tools enable you to keep rigorous track of the physical
parameters that have a direct impact on your mission-critical
storage, research, and transport equipment.
Your satisfaction with OCEASOFT solutions is going to be based on
their reliability and robustness in your particular situation. As such,
we are dedicated to a rigorous approach in designing, developing,
testing, delivering, and following up on our products and solutions.
This quality is something that we prove to our customers consistently.
“Quality
in-house,
quality in
the field”
OCEASOFT continues to focus on ways to better meet and
anticipate your needs, such as with the new Cobalt M solution
dedicated to smart mobile monitoring. Whatever the size of your organization, OCEASOFT
and its distribution partners are ready to give you the close, personal attention you need to
set up the most appropriate monitoring solution for your needs. Our products are distributed
around the entire world and are used by leaders in the health, life science, and research fields.
This catalog presents the OCEASOFT product line, from our wireless and standalone datalogging modules to complete software monitoring tools, alert systems, and related services.
These systems and solutions are designed to give you the peace-of-mind to know that your
projects or products are being monitored 24 hours a day.
For additional details regarding the products featured in this catalog, please contact your
sales representative or check www.oceasoft.com.
Sincerely,
Laurent Rousseau
President of OCEASOFT
3
4
Table of contents
Introduction6
Why you need monitoring
OCEASOFT sensor - datalogging applications
Architecture overview
Cobalt 2 - Advanced wireless monitoring
Cobalt 2 wireless module overview
Digital temperature sensors (internal / external)
Precision temperature sensors (PT100)
Dual humidity & temperature sensor
Dual CO2 & temperature Sensor
Differential pressure sensor
4-20 mA or 0-5 V active output sensor
Dry contact input sensor
Cobalt T - temperature, light & humidity sensors
Cobalt M - Monitoring on the move
Temperature monitoring, light detection
Cobalt 1 - The original wireless monitoring solution
Cobalt 1 wireless module overview
Digital temperature sensors (internal / external)
Precision temperature sensors (PT100)
Dual humidity & temperature sensor
Wireless receivers and repeaters
6
8
9
11
12
14
16
17
18
19
20
21
22
23
24
27
28
30
32
33
35
TCP/IP receiver
36
USB receivers
37
Repeaters38
Alert solutions
Wireless siren
Dry contact alarm controller (IP)
USB telephone modem
OCEAVoice – ThermoServer alerts via the Internet 41
42
43
43
44
Software45
ThermoServer 5 - Thermoclient 5
ThermoClient Mobile for smartphones & tablets
ThermoCalibration: sensor calibration kit
Thermal mapping
Standalone datalogging
46
48
49
50
51
Emerald - temperature tracking with a smartphone
52
LogTag54
Thermo Tracer
56
Services59
Site surveys
60
Installation60
IQ/OQ equipment qualification
61
Maintenance and support contracts (Cobalt)
62
Replacement parts
63
Hosted ThermoServer solution: OCEAHost
64
Calibration / metrology
65
Sales information
71
About OCEASOFT
72
Accreditations / compliance
72
Where to buy
73
Contacting OCEASOFT
73
Shipping74
Product warranty
74
Copyrights74
Product notices
75
Glossary76
Notes77
5
Introduction
Introduction
WHY YOU NEED MONITORING
Don’t leave your lab unattended
Labs, cold-rooms, and storage facilities of all kinds can easily be equipped
with a variety of sensors to monitor specific conditions that are important
to you. Many types of sensors are at your disposal for projects, products, or
research that require stable conditions. Combined with automatic datalogging systems, you can keep track of these conditions even when you
are not around. With OCEASOFT monitoring solutions, from standalone
dataloggers to networked wireless sensor modules, there’s no reason to
leave your critical parameters without 24-hour a day surveillance.
ooTemperature
ooRelative humidity
ooCO2 levels
ooDifferential pressure
oo4-20 mA / 0-5 V output
ooDry contact
“You can’t keep
an eye on all your
refrigerators,
incubators, coldrooms, and storage
facilities all the time,
all by yourself, so let
us help you do it.”
Monitoring on the move
With the right mounting kit it’s easy to place sensors where they need
to be, where they can monitor your permanent installations, equipment,
and facilities. Other sensors can simply be set on a shelf, such as inside
an incubator. In some cases data from these sensors can be downloaded
manually. In others, the data is transmitted wirelessly back to a server at
preprogrammed intervals.
But how can you keep track of temperature when your products or
samples are being transported? It’s a slightly different situation, also one
that OCEASOFT products are designed to handle. For shipments of blood
or food, not only is a timely alert essential in case of temperature change,
but delivery services need to be able to document the fact that proper
shipping conditions were respected on the trip from point A to point B to
point C.
ooBiological samples
ooBlood
ooPharmaceutical products
ooFood
6
Don’t worry, we’ll let you know if
there’s a problem
Monitoring systems are only as good as the information they provide
you. Accuracy, reliability, and long battery life are all important factors
for logging sensor data. An alert system that is responsive to unexpected
changes can bridge the gap between your equipment and yourself,
wherever you may be, whenever the anomaly occurs. The OCEASOFT Alarm
Management System (AMS) is an integral part of the Cobalt software
solution. AMS keeps a constant watch over your data to make sure it stays
within range. If not, it knows how to reach you by phone, fax, e-mail or
instant message.
“Not only do we
help protect your
products, but
OCEASOFT solutions
generate regulatorycompliant audit
trails to protect your
liability.”
ooAutomated alerts
ooWireless sirens
ooEmergency contact groups
ooAudit trails
Peace of mind starts early, and
stays with you for the long-term
OCEASOFT has many years experience helping customers get the most out
of their monitoring solutions. Whether you choose a Cobalt-based wireless
solution or one of our standalone monitoring products, OCEASOFT offers
a complete range of services to get you started efficiently and to ensure
your satisfaction over time. From initial site evaluations to installation,
calibration, training and maintenance, OCEASOFT technical staff is ready
to provide the help you need. We also work closely with a network of
qualified partners who offer services locally around the world.
ooPersonalized pre- and post-sales service
ooIQ/OQ site validation assistance
ooSensor calibration by accredited OCEASOFT laboratory
ooHotline and support contracts
ooTraining
7
OCEASOFT SENSOR - DATALOGGING APPLICATIONS
OCEASOFT datalogging solutions help protect your critical samples, materials, and products by
monitoring critical parameters in a wide range of situations. Our Cobalt, Emerald, ThermoTracer, and
LogTag products are adapted to various uses, applications, and industry sectors as summarized below:
Standalone
solutions
Wireless solutions
Cobalt Cobalt
T
M(2)
Sectors
Life science, health,
medical
Food
Transport
Features
Parameters
Temperature
Temperature
Humidity +
Temperature
Temperature
21
Temperature
20
Humidity +
Temperature
x
19
Temperature
x
x
18
22
x
24
x
28
x
30
x
52
x
54
x
54
x
56
x
x
x
x
x
x
x
x
x
x
x
x
ThermoTracer
Temperature
x
17
x
Cobalt
Emerald LogTag (1)
1 (1)
Temperature,
light, humidity
x
Dry contact
x
4-20 mA / 0-5 V
x
Differential
pressure
16
CO2 +temp.
14
x
Humidity +
Temperature
14
x
PT100
Temperature
(external sensor)
Environments
See page:
Ambient temp.
Cargo, packages
Cold rooms
Refrigerators
Freezers
-80°C Freezers
Nitrogen tanks
Water baths
Incubators
Ovens
Clean rooms
Active sensors
Detection systems
Temperature
(internal sensor)
Cobalt 2 (1)
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Humidity
Differential pressure
Voltage
CO2
Light
Binary on/off
x
x
x
x
x
x
x
x
x
x
x
Display
Alert system
Real-time alerts
Datalogging
Wireless monitoring
Replaceable battery
Data on Cloud
USB cradle
Companion
software
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
ThermoServer - ThermoClient
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Emerald
View
LogTag
x
x
ThermoTracer
OCEASOFT monitoring solutions and their applications. (1) Modules sold separately. (2) With dedicated Cobalt M client software.
ABOUT THIS CATALOG
The reference numbers provided in this catalogue are for modules with sensors. Please contact OCEASOFT
directly for ordering sensors and/or modules separately.
In product references, replace the “#” symbol with the code for your geographical zone:
1 = 867 MHz; 2 = 868 MHz, 3 = 915 MHz, 4 = 434 MHz, 5=2.4 GHz (Bluetooth)
Reading precision depends on target ranges. Please see Calibration section for more details.
8
ARCHITECTURE OVERVIEW
The Cobalt wireless monitoring system is a fully integrated wireless sensor
network solution that is comprised of:
Sensors
Digital and analog sensors capable of
measuring a variety of critical parameters, such
as temperature, relative humidity, C02, voltage
output, etc.. These sensors are connected to, or
integrated in, the Cobalt modules.
Cobalt
2 and
Cobalt 1
modules
These battery-powered modules read their
sensors and then log the data in internal
memory. Stored data is then transmitted
wirelessly to a central server.
Wireless
repeaters
Repeaters may be used to provide extra
wireless range between modules and receivers
if necessary.
Wireless
receivers
Connected directly to the server computer or
elsewhere on a TCP/IP network, receivers forward
data from modules to the server database and
transmit read requests from software.
Clientserver
software
Manages wireless configuration and
communications, 24/24 data collection, reports,
alerts, and all other solution parameters.
The diagram below shows how these components fit together in a typical layout:
Sample Cobalt solution
9
10
Cobalt 2
Advanced wireless monitoring
OCEASOFT’s secondgeneration environment
monitoring system
with one-touch
setup, LCD displays,
unparalleled wireless
range and battery life.
Cobalt 2 - Advanced wireless monitoring
11
Cobalt 2
Advanced wireless
monitoring
COBALT 2 WIRELESS MODULE OVERVIEW
Cobalt 2 is a highly reliable wireless datalogger that reads connected sensors at programmable intervals, stores
the data locally, and then transfers it wirelessly to the ThermoServer database, as described in the previous
section. This product is the technological evolution of OCEASOFT’s flagship Cobalt 1 module (see page 27), now
also featuring:
ooInformative LCD display with latest reading,
module details, signal strength, and
remaining battery level
ooOne-touch wireless configuration
ooA wide range of supported sensors
Did you know?
The wireless range
of Cobalt modules
is equal to about 1/3
that of a cell phone,
but with 80 times
less output power!
Easy to change battery
(non-proprietary)
12
Common Cobalt 2 features
All Cobalt 2 products offer the following features:
..Configurable data-logging, transmission cycles
..Mounting kit with plastic holder, magnet, screws,
..Automatic alarms for out-of-bounds conditions
..Size: 132.7 x 64.2 x 34 mm (5.2 x 2.5 x 1.3 in.)
and upper/lower limits
and technical problems
..Easy-to-read LCD display with latest reading,
alerts, signal strength, and battery level
..On-board memory for up to 3,000 readings
cable ties, plastic cable holders and Velcro®
..Weight (depending on model):
• ~150 g (5.3 oz.)
..Fully integrated with ThermoClient /
ThermoServer software suite (which includes
installation guides for all Cobalt 2 products)
(1,500 + 1,500 for dual modules)
..3.6V Lithium battery (3600 mAh) providing up to
4 years service (depending on conditions)
..Type approvals: CE EN 300-220-1, FCC, EN12830, IC
(Industry Canada), WPF (India), CMIIT (China)
..Plastic ABS casing with IP65 protection for indoor
use (some models available with IP66/67 casing)
..Wireless module operating conditions
• -0°C to +50°C (standard)
• -30°C to +50°C (with IP66/67 option)
• 0 to 90% RH, non-condensing
Wireless specifications
OCEASOFT products integrate a robust wireless module that offers industry-leading range, reliability and
efficient power usage:
vvOne-touch configuration using Service Discovery
Protocol, with automatic reconnection
vvISM (Industrial Scientific Medical) band with four
frequencies: US/CAN 915 MHz; Europe 868 MHz;
APAC 434 MHz; India and other countries 867
MHz
vvIndoor wireless range:
• 25-100 meters (82-328 ft.); up to 400 meters
(1,312 ft.) with 3 repeaters
vvLine-of-sight range: approximately 700 meters
(2,300 ft.)
vvChannel width: 50 kHz
vvFrequency deflection: 16 KHz (867/868/915 MHz),
9 KHz (434 MHz)
vvTransmission speed: 9600 Baud in NRZ mode
vvModulation type: GFSK
vvDriven receiver sensitivity for BER = 1%:
-107 dbm to -110 dBm
vvDriven transmission: 8 dBm to 10 dBm
vvPower output:10 mW (434 MHz) or
25 mW (867/868/915 MHz)
vvIntegrated repeater functionality to extend
range of other modules
North America:
915 MHz
Wireless ISM
frequencies used
by OCEASOFT
products around
the world
South America:
915 MHz
Europe:
868 MHz
Asia:
434 MHz
867 MHz
India:
867 MHz
Pacific:
434 MHz
13
DIGITAL TEMPERATURE SENSORS (INTERNAL / EXTERNAL)
Cobalt 2 modules can be equipped with a variety of digital temperature
sensor types. Internal and external sensor options are available,
depending on the target application, such as monitoring ambient
temperatures, food products, incubators, or freezers. Digital sensors
are read directly by the Cobalt 2 signal processor to ensure consistent
accuracy over time. Data is logged locally in Cobalt 2 memory and
transmitted wirelessly to a host computer at programmable intervals.
Alerts can be sent automatically in case these readings indicate alarm
conditions as configured in the software.
Simple
recalibration of
digital sensors
via standard
exchange
Common features
..Digital temperature sensors (resolution
..Fully integrated with ThermoServer / Thermo
..Temperature ranges to match various
..Automatic alert transmission for out-of-
..Cobalt 2 wireless module with LCD and
..On-board memory for 3,000 measurements
0.0625°C)
application needs
battery (3.6V Lithium, 3600 mAh)
..ISO/IEC 17025 (Cofrac) accredited calibration(1)
available, please contact us
Client software solution
bounds conditions and technical issues
..Wireless range indoors: 25-100 meters (82328 ft.) point-to-point; up to 400 meters
..Mounting kit
14
Cobalt 2 module options
Specific details
Cobalt 2 with one internal
temperature sensor
for measuring ambient
temperature
•
•
+10° to +50°C
Self-contained module
•
•
•
•
-40° to + 80°C
Up to 2 sensors per Cobalt module
Sensor : Ø 6 mm, L 30 mm
Module cable 1.5 m + sensor cable 1 m
(including connector)
Waterproof with extended
range external temperature
sensor for ovens, incubators
and water baths
•
•
•
•
-40° to + 120°C
Sensor: Ø 6 mm, L 30 mm
(incl. connector)
External contact sensor for
monitoring water pipes,
Legionella conditions, water
baths
•
•
•
-40° to + 80°C
L 40 mm, W 16 mm, H 8.5 mm
(incl. connector)
•
•
•
-40° to + 120°C
L 150 mm, Ø 6 mm, handle 100 mm
(incl. connector)
External temperature sensor
for refrigerators, cold rooms,
freezers, ovens, incubators
Insertion probe, typically for
sampling temperature in
food products.
References (Cobalt 2 module + digital sensor)
Cobalt 2 module
Sensor
type
Internal
temp.
# Sensors Range °C
1
Standard
module
+10 to +50°C
COB#0119122
-40 to + 80°C
COB#0201122
(1 m cable
standard)
-40 to + 120°C
COB#0203122
-40 to + 80°C
COB#0301122
(2)
Module with options
IP66 casing
(transparent)
External
power option
COB#0220132
(internal = IP67)
COB#0201132
1
External
temp.
2
Contact
Insertion
1
2
1
-40 to + 120°C
-40 to +80°C
-40° to +120°C
Also available with
opaque casing:
COB#0201152
COB#0201322
COB#0202132
COB20202322
COB20301322
COB20302322
COB#0303122
COB#0303322
COB#0204122
COB#0304122
COB#0205122
COB#0205132
(1) Accuracy depends on target temperature. Please see Calibration section for more details. (2) Replace # for
your geographical zone in product references: 1 = 867 MHz; 2 = 868 MHz, 3 = 915 MHz, 4 = 434 MHz
15
PRECISION TEMPERATURE SENSORS (PT100)
Cobalt 2 modules are available with three types of precision PT100
sensors to cover a wide range of applications, from liquid nitrogen tanks
to high-temperature kilns. Each external analog sensor is connected
to the Cobalt 2 module via a robust cable designed for the target
temperature range. Data is logged locally on the Cobalt 2 module and
Common features
..3-wire, Class B PT100 sensors (1)
(resolution 0.07°C)
application needs
..Wireless range indoors: 25-100 meters (82-
328 ft.) point-to-point; up to 400 meters
..Mounting kit
Cobalt 2 PT100 module options
Specific details
•
•
•
•
•
•
•
•
•
References (Cobalt 2 module + PT100 sensor)
Cobalt 2 module
Sensor
type
External
# Sensors Range °C
1
Standard
module
-100 to +150°C for ultra-lowtemperature freezers
Ø 3 mm, L 100 mm
Module cable 1.5 m + PTFE sensor cable 3.5 m
-200 to +50°C for LN2 and cryogenic
freezers
Ø 3 mm + 5 mm, L 150 mm
Module cable 1.5 m + PTFE sensor cable 1.4 m
+100 to +348°C for ovens, incubators, kilns
Ø 3 mm + 5 mm, L 150 mm
Module cable 1.5 m + glass silk sensor
cable 2 m
(3)
Module with options
IP66 casing
(transparent)
-100°C to +150°C
COB#0506122
COB#0506132
-200°C to +50°C
COB#3807122
COB#3807132
+100°C to +350°C
COB#3908122
COB#3908132
Industryleading high
precision
temperature
measurement
(1) 4-wire and Class A sensors are also available. Please contact your sales representative. (2) Accuracy
depends on target temperature. Please see Calibration section for more details. (3) Replace # for your
geographical zone in product references: 1 = 867 MHz; 2 = 868 MHz, 3 = 915 MHz, 4 = 434 MHz
16
DUAL HUMIDITY & TEMPERATURE SENSOR
The Cobalt 2 wireless humidity / temperature module includes is a dualfunction device that logs both relative humidity levels and temperature.
This module is generally used in various types of storage, medical and
tracking applications. The Cobalt 2 module collects and stores humidity
(RH) and temperature readings from the connected sensor module
at regular intervals and transmits them to a computer running the
ThermoServer / ThermoClient system management software.
Features
..Digital temperature (resolution 0.0625°C) /
relative humidity sensor (resolution 0.025%
RH), 4-wire connector
..Range -40°C to +100°C and 0% to 99.9% RH
(2 x 1500)
..Mounting kit
Dual humidity & temp. sensor for Cobalt 2
Cobalt 2 with combination
digital temperature and
relative humidity sensor
for monitoring ambient
room environments and
stabilization cabinets.
References (Cobalt 2 module + dual sensor)
Cobalt 2 module
Sensor
type
#
Sensors
External
T + RH
1
Specific details
•
•
•
Sensor: IP67 protection
33 x 11.6 mm plastic casing with PTFE
filter
Standard cable length: 80 cm module
cable, 20 cm ribbon cable (for door
gaskets), IP40 protection
Extension cable: 1 m
IP67 protection for connectors
(for total length of 1.8 m)
(2)
Module with options
Standard
module
IP66 casing
(transparent)
External
power
IP67
extension
cable
Measure 2
parameters
with one
sensor!
COB#0413122 COB#0413132 COB#0413322 contact us
17
DUAL CO2 & TEMPERATURE SENSOR
The Cobalt 2 C02 wireless module is a dual-function device that monitors
both C02 concentration and temperature. The sensor module is placed
upright inside the incubator and connected to the Cobalt 2 module
outside the incubator via a flat ribbon cable.
Features
..Single external module with digital
temperature (res. 0.0625°C) and CO2
(0.0625%) sensors
(1,500 temp / 1,500 CO2)
..Mounting kit
..4-wire flat ribbon cable, 1 m
Dual CO2 & temp. sensor for Cobalt 2
Specific details
•
Cobalt 2 with external
module containing both
CO2 and digital temperature
sensor for use inside
incubators.
References (Cobalt 2 module + CO
2
•
•
•
Measures temperature: 0°C to +50°C,
CO2: 0 to 9.99%
Module powered by external AC
adapter, with backup battery
Dimensions: 79.5 x 76.5 x 45.5 mm (3.1
x 3.0 x 1.8 in.)
External sensor unit with IP44
protection, plastic casing (ABS,
polycarbonate) with PTFE filter;
operation 0 - 50°C and 0 to 95% RH non
condensing for indoor use
/ temperature sensor) (2)
Cobalt 2 module
Sensor
type
External
# Sensors Range °C
1
CO2: 0% / 9.99%
Temp: 0° to +50°C
Standard module
Measure 2
parameters
with one
sensor!
COB#1014222
18
DIFFERENTIAL PRESSURE SENSOR
The Cobalt differential pressure module contains two pressure sensors,
enabling you to compare the relative pressure between two zones, such
as physically separated rooms. This module is typically placed in the room
in which the ambient pressure is considered as “normal.” A tube is placed
on one of the module’s inputs to measure the pressure in another room.
The Cobalt differential pressure module is particularly suitable for use in
monitoring “clean” and “dirty” laboratory areas.
Features
..Internal digital differential pressure sensor
..Calibration traceable to Cofrac(1) available,
(resolution 0.0625 Pa)
please contact us
..Mounting kit
Differential pressure sensor for Cobalt 2
Specific details
•
Cobalt 2 with internal
differential pressure sensor
for use in monitoring “clean”
and “dirty” laboratory areas.
References (Cobalt 2 module + integrated sensor)
•
•
•
•
Pressure measurable from -500 Pa to
+500 Pa (-2 to +2 in. / -5 to +5 cm in H2O)
Tube length: 50 cm
Diameter: 4 mm (4-5 mm adapter
included)
Full compatibility: Air, N2
Limited compatibility: O2
Allowable overpressure: 1 bar (100 kPa,
400 inches H2O)
(2)
Cobalt 2 module
Sensor
type
Internal
# Sensors Range
1
-500 / +500 Pa
Standard module
COB#1216122
Batterypowered
module stores
up to 3,000
readings in onboard memory
19
4-20 MA OR 0-5 V ACTIVE OUTPUT SENSOR
The Cobalt 2 4-20 mA or 0-5 V wireless monitor can be connected to any
industry-standard device that generates an active output current of 4-20
mA or 0-5 V, which can be measured to provide status information in a
variety of applications, ranging from speed and wind monitors to angle
and position devices to particle counters and ultra-low-temperature
(ULT) freezers, and more. These modules are typically installed in a
convenient location at room temperature. Read values are converted into
useful information by the ThermoServer-ThermoClient application and
displayed on the Cobalt end-point module.
Features
..Internal 4-20 mA or 0-5 V input sensor
available for 4-20 mA module only, please
contact us
..Mounting kit
..Automatic alert transmission for out-ofbounds conditions and technical issues
Cobalt 2 with 4-20 mA or 0-5 V sensor
Specific details
For logging levels of
electrical current in industrystandard devices
References (Cobalt 2 module + integrated sensor)
Cobalt 2 module
Sensor
type
•
•
Cable length 2.9 m
2-wire cable to connect to a device that
generates 4-20 mA or 0-5 V current
(2)
Options
# Sensors Range
Standard module
IP66 casing
(transparent)
Internal
1
4 - 20 mA input
COB#0700122
COB#0700132
Internal
1
0 - 5 V input
COB#0800122
COB#0800132
Converts
current data
into useful
values for easy
reading
(1) Accuracy depends on target currents. Please see Calibration section for more details. (2) Replace # for
20
DRY CONTACT INPUT SENSOR
The Cobalt dry contact wireless module can be connected to any industrystandard device with a dry contact output. As dry contact devices do not
generate any power, the Cobalt module emits a low current to detect
whether the switch on the other device is open or closed.
Typical devices that provide a dry contact output include alarm units,
door open/close sensors, and switches. The Cobalt module can be
configured to detect either a “normally closed” or “normally open” state
to correspond with the device to monitor. The Cobalt module indicates
open or closed status in large characters on its LCD display.
Features
..Internal dry contact input sensor
..Mounting kit
Cobalt 2 with dry contact sensor
Specific details
Cobalt 2 with internal dry
contact sensor for logging
binary (on/off, open/closed)
states.
•
•
Cable length 2.9 m
2-wire cable to connect to a device that
generates dry contact signal
References (Cobalt 2 module + integrated dry contact sensor)
Cobalt 2 module
Sensor
type
Internal
# Sensors Range
1
On / off
Standard module
COB#0900122
(1)
Options
IP66 casing (transparent)
COB#0900132
Displays
remote
sensor’s open/
close status at
all times
(1) Replace # for your geographical zone in product references: 1 = 867 MHz; 2 = 868 MHz, 3 = 915 MHz, 4
= 434 MHz
21
COBALT T - TEMPERATURE, LIGHT & HUMIDITY SENSORS
Cobalt T is equipped with sensors to monitor ambient
conditions in research laboratories that use animals. Measuring
temperature, relative humidity and day/night light cycles, Cobalt
T meets the requirements of the European Parliament’s 2010/63/
UE directive concerning the protection of animals used for
scientific purposes.
Current values are displayed on an easy-to-read screen, with data
transferred wirelessly at regular intervals to a central database.
Cobalt T can be installed as a complement to existing Cobalt
wireless monitoring systems or in new installations. Wireless
transmission is fast and easy to set up.
Features
..Cobalt T wireless module with LCD and user-
..Internal temperature sensor (res. 0.0625°C),
replaceable battery (3.6V Lithium, 2600 mAh)
light sensor, external humidity sensor
(resolution 0.025% RH)
..On-board memory for 3,000 readings
..Monitors day-night cycles
..Mounting kit
Cobalt T with three sensors
Specific details
•
Multi-parameter wireless
module to monitor animal
conditions in research
laboratories
References (Cobalt T module + 3 sensors)
•
•
Measures temperature: -30°C to +50°C,
humidity: 5 to 95% RH
Casing: IP 65 protection
Sensor: IP67 protection (33 x 11.6 mm
plastic casing with PTFE filter)
Easy recalibration by standard
exchange
(2)
Cobalt T module
Sensor
type
Int. & ext.
# Sensors Range
3
-30°C to +50°C
5 to 95% RH
Standard module
COB#4313122
Multiparameter
wireless
monitoring for
research labs
(1) Accuracy depends on target currents. Please see Calibration section for more details. (2) Replace # for
22
Cobalt M
Smart datalogging
and wireless
connectivity
for transport
and delivery
applications
Cobalt M - Monitoring on the move
23
Cobalt M
TEMPERATURE MONITORING, LIGHT DETECTION
Designed for use inside refrigerated trucks and containers, Cobalt M
monitors and records air temperature to protect temperature-sensitive
products and provide tracking details to prove conditions during transit.
Drivers can be alerted via a wireless siren if the temperature inside the
refrigerated chamber changes unexpectedly.
The module, which also operates submersed in liquid, transmits stored
data wirelessly and provides a complete audit trail to analyze refrigeration
system performance. The module integrates a light sensor with patented
door open/close detection, offering wireless range up to 400 meters and
battery life of at least one year. Cobalt M memorizes delivery locations for
viewing with Google Maps.
Features
..Internal temperature sensor (resolution
0.0625°C), light detector
..Cobalt M wireless module with inclined LCD,
..ISO/IEC 17025 (Cofrac) certified or traceable
calibration(1) available, please contact us
..Lockable mounting kit
..Documentation CD-ROM
..Completely integrated with ThermoServer
5 solution (software may be launched from
ThermoClient or separately)
..On-board memory for 3,000 total
measurements
..Wireless range indoors:
25-100 meters (82-328 ft.) point-to-point(2)
Specially
designed for
datalogging
in mobile
scenarios
24
Cobalt M with temperature and light sensor Specific details
Cobalt M for transport
applications in food, health,
and life science sectors
•
•
•
•
Temperature range: -30°C to +50°C
Dimensions: 86 x 64 x 29.6 mm (3.4 x
2.5 x 1.2 inches)
IP65 protection, water resistant
Battery life 1 year or more, depending
on use (user-changeable battery)
References (Cobalt M module + integrated temperature and light sensor)
Sensor type
Internal
# Sensors
1
Range
-30°C to +50°C
Standard module
COB#2521122
(1) Accuracy depends on target currents. Please contact us for more details. (2) Please see page 13 for details
regarding wireless properties.
25
26
Cobalt 1
The original wireless solution
The Cobalt
module that
started it all:
great wireless
connectivity for a
variety of sensor
types
Cobalt 1 - The original wireless monitoring solution
27
Cobalt 1
Wireless monitoring
COBALT 1 WIRELESS MODULE OVERVIEW
The original OCEASOFT Cobalt product, the Cobalt 1 sensor monitoring module offers outstanding wireless
performance in terms of range and robustness against interference, as well as long battery life. Cobalt 1 is
available with the following sensor types:
ooInternal temperature sensor
ooExternal digital and analog sensors
ooPT100 sensors (high precision measurements)
ooDual digital temperature and humidity sensor
ooContact temperature sensors
OCEASOFT’s
original datalogger
with class-leading
wireless range and
a variety of sensor
options
Easy to change
battery (nonproprietary)
28
Common Cobalt 1 features
All Cobalt 1 products offer the following features:
..Simple push-button operation
..Wireless module operating conditions:
..Configurable data-logging, transmission cycles
• -0°C to +50°C (standard)
..Automatic alarms for out-of-bounds conditions
• 0% to 90% RH, non-condensing
• -30°C to +50°C (with IP66/67 option)
and upper/lower limits
and technical problems
..Mounting kit with plastic holder, magnet, screws,
..Red / green LED status indicator
cable ties, plastic cable holders and Velcro®
(1,500+1,500 for dual modules)
..3.6V Lithium battery (2600 mAh) providing up to
2 years service (depending on conditions)
..Size: 90 x 58 x 25 mm (3.5 x 2.3 x 1.0 in.)
..Weight: 120 g (4.2 oz.)
..Fully integrated with ThermoClient /
ThermoServer software suite
..IP44 protection for indoor use (some models
available with optional IP66/67 casing
Wireless specifications
OCEASOFT products integrate a robust wireless module that offers industry-leading range, robustness and
efficient power usage:
vvISM (Industrial Scientific Medical) band with four
frequencies: US/CAN 915 MHz; Europe 868 MHz;
India and other countries 867 MHz
vvIndoor wireless range:
• 25-100 meters (82-328 ft.)
• Up to 400 meters (1,312 ft.) with 3 repeaters
vvLine-of-sight range: approximately 500 meters
(1,650 ft.)
vvTransmission speed: 9600 Baud in NRZ mode
vvModulation type: GFSK
vvDriven receiver sensitivity for BER = 1%:
-107 dbm to -110 dBm
vvDriven transmission: 8 dBm to 10 dBm
vvPower output:
25 mW (867/868/915 MHz)
vvIntegrated repeater functionality to extend
range of other modules
vvChannel width: 50 kHz
vvFrequency deflection: 16 KHz
North America:
915 MHz
Wireless ISM
frequencies used
by OCEASOFT
products around
the world
South America:
915 MHz
Europe:
868 MHz
Asia:
434 MHz
867 MHz
India:
867 MHz
Pacific:
434 MHz
29
DIGITAL TEMPERATURE SENSORS (INTERNAL / EXTERNAL)
Cobalt 1 modules may be equipped with a variety of digital temperature
sensor types. Internal and external sensor options are available,
depending on the target application, such as monitoring ambient
temperatures, food products, incubators or freezers. These digital sensors
are read directly by the Cobalt 1 signal processor to ensure consistent
accuracy over time. Data is logged locally on the Cobalt 1 module and
A cost-effective
and reliable
temperature
monitoring
solution
Common features
..Digital temperature sensors (resolution
..Cobalt 1 wireless module with battery
0.0625°C)
application needs
(3.6V Lithium, 2600 mAh)
..Mounting kit
30
Cobalt 1 module options
Specific details
Cobalt 1 with one internal
temperature sensor
for measuring ambient
temperature
for refrigerators, cold rooms,
freezers, ovens up to 80°C
Extended range external
temperature sensor for
ovens, incubators and water
baths
External contact sensor for
monitoring water pipes,
Legionella conditions
References (Cobalt 1 module + digital sensor)
Cobalt 1 module
Sensor
type
Internal
temp.
# Sensors Range °C
1
1
External
temp.
Contact
2
1
2
Standard
module
•
•
+10° to +50°C
Self-contained module
•
•
•
•
-40° to + 80°C
Ø 6 mm, L 30 mm
•
•
•
•
-40° to + 120°C
Sensor: Ø 6 mm, L 30 mm
•
•
•
-40° to + 80°C
L 40 mm, W 16 mm, H 8.5 mm
(2)
Module with options
IP66 casing
(transparent)
External
power option
COB#0119111
+10 to +50°C
COB#0119101
-40 to + 80°C
COB#0201101
COB#020111
Contact us
-40 to + 120°C
COB#0203101
COB#0202111
Contact us
-40 to + 80°C
COB#0301101
-40 to + 120°C
COB#0303122
-40 to +80°C
(internal = IP67)
COB#0204101
COB#0304101
your geographical zone in product references: 1 = 867 MHz; 2 = 868 MHz, 3 = 915 MHz
31
PRECISION TEMPERATURE SENSORS (PT100)
Cobalt 2 modules are available with three types of precision
PT100 sensors to cover a wide range of applications, from liquid
nitrogen tanks to high-temperature kilns. Each external analog
sensor is connected to the Cobalt 2 module via a robust cable
designed for the target temperature range. Data is logged
locally on the Cobalt 2 module and transmitted wirelessly to a
host computer at programmable intervals. Alerts can be sent
automatically in case these readings indicate alarm conditions as
configured in the software.
Common features
..4-wire, Class A PT100 sensor (res. 0.01°C)
application needs
..Cobalt 1 wireless module with battery (3.6V
Lithium, 2600 mAh)
..Mounting kit
PT100 sensor for Cobalt 1
Specific details
•
•
•
-100 to +150°C for high-precision
measurements
Ø 3 mm, L 100 mm
References (Cobalt 1 module + PT100 sensor)
(2)
Cobalt 1 module
Sensor type
External
# Sensors
1
Range °C
-100°C to +150°C
Standard module
COB#0512101
High-precision
temperature
monitoring
solution
(1) Accuracy depends on target temperature. Please see Calibration section for more details. (2) Only
available for 868 MHz.
32
DUAL HUMIDITY & TEMPERATURE SENSOR
The Cobalt 1 wireless humidity / temperature module is a dualfunction device that logs both relative humidity levels and
temperature. This module is generally used in various types of
storage, medical and tracking applications. The Cobalt 1 module
collects and stores humidity (RH) and temperature readings from
the connected sensor module at regular intervals and transmits
them to a computer running the ThermoServer / ThermoClient
system management software.
Features
..Digital temperature (res. 0.0625°C)/ relative
humidity sensor (res. 0.025 %RH), 4-wire
connector
..Range -40°C to +100°C and 0% to 99.9% RH
..Cobalt 1 wireless module with battery
(3.6V Lithium, 2600 mAh)
..Mounting kit
Dual humidity & temp. sensor for Cobalt 1
Cobalt 1 with combination
digital temperature and
relative humidity sensor
for monitoring ambient
room environments and
stabilization cabinets.
References (Cobalt 1 module + dual sensor)
Cobalt 1 module
Sensor
type
#
Sensors
External
T + RH
1
Specific details
•
•
•
Sensor: IP67 protection
33 x 11.6 mm plastic casing with PTFE
filter
Standard cable length: 80 cm module
cable, 20 cm ribbon cable (for door
gaskets), IP40 protection
Extension cable: 1 m
IP67 protection for connectors
(for total length of 1.8 m)
(2)
Module with options
Standard
module
IP66 casing
(transparent)
External
power
IP67
extension
cable
Two sensors
integrated into
a single unit
COB#0413122 COB#0413132 COB#0413322 contact us
your geographical zone in product references: 1 = 867 MHz; 2 = 868 MHz, 3 = 915 MHz
33
34
Wireless receivers
& repeaters
Simple and
robust network
infrastructure to
build your wireless
monitoring
solution
Wireless receivers and repeaters
35
TCP/IP RECEIVER
Plugged into your local Ethernet network, TCP/IP receivers collect data
wirelessly from your Cobalt monitoring modules and transfer it to the
ThermoServer data monitoring software.
Network receivers are particularly useful when you need to read
large groups of Cobalt modules that are located remotely from the
ThermoServer computer receiving the data.
Features
..Includes antenna, 10/100BT RJ-45 connector,
mounting kit, and AC adapter
..Wireless range from 25-100 meters (65-325
ft.) indoors; up to about 700 meters (2,300
ft.) in line of sight
..Compatible with Cobalt 2 (including
automatic wireless configuration using
Service Discovery Protocol) and Cobalt 1
..Dimensions: 190 x 52 x 30 mm (7.4 x 2 x 1.2
in.)
..Supports a nearly unlimited number of endpoint modules
..Output power:(1)
• 25 mW in 867 / 868 / 915 MHz regions
..Windows 32- and 64-bit drivers,
• 10 mW in 434 MHz regions
documentation CD-ROM
Wireless receivers (TCP/IP connection)
Specific details
•
Standard external power
device
•
110/240 V AC Adapter with 4
international plug formats
Option: 25/500 mW automatic
switching for use with 500 mW
repeaters in 867 / 868 / 915 MHz
regions
Power-over-Ethernet device
(PoE)
•
Power supplied by Ethernet network
(must be enabled by your router)
References
(2)
Type
Standard 110/240V AC
Power-over-Ethernet
(PoE)
Frequency
Power output
Models
25 / 100 mW
COB#1900242
25
COB#1800242
434
10
COB41800242
867, 868, 915
25 mW
COB#2000242
434
10 mW
COB42000242
867, 868, 915
Supports
automatic network
configuration (see
us on Youtube®:
“OCEASOFT
New Wireless
datalogger”)
(1) Cobalt modules all communicate with 25 mW or 10 mW, depending on the region. Some repeaters
support automatic 25/500 mW switching for extra range to reach a 25/500 mW receiver. Please check
with us for more details on defining network topology. (2) Replace # for your geographical zone in product
references: 1 = 867 MHz; 2 = 868 MHz, 3 = 915 MHz, 4 = 434 MHz
36
USB RECEIVERS
Plugged directly into your ThermoServer host computer, USB
receivers collect data wirelessly from your Cobalt monitoring
modules and transfer it to the ThermoServer data monitoring
software.
USB receivers are generally used when your Cobalt modules
are within about 100(1)meters from the ThermoServer computer
receiving the data.
Features
..Includes antenna and mounting kit
..Windows 32- and 64-bit drivers,
..Wireless range from 25-100 meters (65-325
ft.) indoors; up to about 700 meters (2,300
ft.) in line of sight
..Compatible with Cobalt 2 and Cobalt 1
documentation CD-ROM
..Dimensions: 90 x 50 x 25 mm (3.5 x 2 x 1.0
in.)
..Output power:
..Supports a nearly unlimited number of endpoint modules
USB receiver for ThermoServer computer
Standard USB-powered
device
• 25 mW in 867 / 868 / 915 MHz regions
• 10 mW in 434 MHz regions
Specific details
•
•
References
(2)
Product
USB
Receiver
Frequency
Output
power
Models
867, 868, 915
25 mW
COB#1500002
434
10 mW
COB41500002
USB connection
Automatically detected by
ThermoServer installation wizard
No external
power supply
required directly powered
via USB.
(1) This range can be extended by using wireless repeater modules. (2) Replace # for your
geographical zone in product references: 1 = 867 MHz; 2 = 868 MHz, 3 = 915 MHz, 4 = 434
MHz
37
REPEATERS
A repeater extends the range between wireless nodes in the Cobalt
monitoring system, such as between far-away Cobalt modules and a
receiver on your ThermoServer computer.
While Cobalt modules and receivers offer best-in-class wireless range, it is
sometimes necessary to use repeaters to improve overall signal strength
and to cover hard-to-reach locations reliably.
Features
..Includes antenna, mounting kit, 110/240 V AC
adapter, documentation CD-ROM
..Indoor wireless range:
..Line-of-sight: appr. 700 meters (2,300 ft.)
..Compatible with Cobalt 2 and Cobalt 1
Wireless repeaters (range extenders)
• 25-100 meters (82-328 ft.)
• Up to 400 meters (1,312 ft.) with 3
repeaters (up to 3 repeaters may be cascaded
in a given network branch)
Specific details
•
Standard repeater module
Cobalt 2 module with
integrated repeater feature
Cobalt 1 module with
integrated repeater feature
•
•
•
•
•
•
•
•
10 or 25/500 mW operation and
automatic switching(1) for optional use
with 500 mW repeaters
110/240 V AC adapter
Dimensions: 190 x 52 x 30 mm
(7.4 x 2 x 1.2 in.)
10 or 25 mW standard output power
Internal +10 to + 50°C temperature
sensor, power outage detection
Battery or 110/240 V AC adapter
10 or 25 mW standard output power
Internal +10 to + 50°C temperature
sensor, power outage detection
Battery or 110/240 V AC adapter
38
References
Type
Standard
Cobalt 2
Cobalt 1
Power output
Models(2)
25/500 mW
COB#1900242
25 mW
COB#1800242
10 mW
COB42400242
25 mW
COB#1319322
10 mW
COB41319322
25 mW
COB#1319301
10 mW
COB41319301
Supports up
to 3 repeaters
in a row for
maximum
range!
(1) Cobalt sensor modules all communicate with 25 mW; repeaters support automatic 25/500 mW switching
for extra range to reach a 25/500 mW receiver. Please check with us for more details on defining network
topology. (2) Replace # for your geographical zone in product references: 1 = 867 MHz; 2 = 868 MHz, 3 =
915 MHz, 4 = 434 MHz
39
40
Alert solutions
Keeping you aware
of anomalies that
may occur in the
environments you
monitor
Alert solutions
41
WIRELESS SIREN
OCEASOFT wireless sirens are used to raise alerts if alarm conditions are
detected on the modules in your Cobalt wireless monitoring system.
For example, you could configure a Cobalt temperature module to
trigger an alarm if the temperature exceeds an upper limit, or drops
below a lower limit. The siren is triggered when an alarm sent by the
Cobalt module is detected by the software.
Features
..Siren volume output from 60 to 100 dBA
..110/240V AC power adapter and mounting
..Wireless range up to 200 meters (650 ft)
..Optional car cigarette lighter adapter
(± 10%)
in open space, from 8 meters (26 ft) to 30
meters (98 ft) indoors, and up to 120 meters
(390 ft) indoors with 3 repeaters
..Plastic casing: ABS and polycarbonate with
IP54 protection
kit
available for in-vehicle use with Cobalt M
..Operating temperature range: 0°C to +50°C
..Size: 160 x 80 x 83 mm (1.6 x 3.1 x 3.3 in.)
..Weight: 400 g (14.1 oz.)
References
Product
Wireless siren
Wireless siren with
cigarette lighter adapter
Reference(1)
COB#2600202
contact us
(1) Replace # for your geographical zone in product references: 1 = 867 MHz; 2 = 868 MHz, 3 = 915 MHz, 4
= 434 MHz
Sound and
light grab your
attention fast!
42
DRY CONTACT ALARM CONTROLLER (IP)
As part of your Cobalt Alarm Management System, the OCEASOFT TCP/
IP Dry Contact alarm controller triggers alerts on one or two external dry
contact devices when the system detects alarms from end-point modules.
Configure a Cobalt temperature monitoring module to trigger an alarm
if the temperature exceeds, or drops below, a specified limit. The TCP/
IP Dry Contact device receives the alarm signal over the TCP/IP (Ethernet)
network and triggers the alarm on a connected dry contact device(s).
Features
..100/240 V AC power adapter with
international plugs and 1 meter (3.3 ft.) cable
..Output: 24V DC - 0.4 A
..RJ-45 Ethernet cable (2 meters / 6.5 feet)
..Size: 102 x 54 x 30 mm
..Two simultaneous dry contact outputs,
configurable as “normal open” or normal
“closed)
References
Product
Models (1)
Dry contact IP
COB08100201
(1) Please indicate the desired IP address, gateway, and network mask for your network when you place your order.
USB TELEPHONE MODEM
The OCEASOFT USB modem is a key part of your Cobalt Alarm
Management System. The modem is connected to a dedicated analog
phone line to notify users in case anomalies are detected by Cobalt
modules. The modem, designed by US Robotics, has been optimized in
cooperation with OCEASOFT to properly support the alert types required
by the ThermoServer software.
Features
..Sends alerts via voice call and fax
..USB plug and RJ-11 phone socket
..Power and data transmission LED indicators
..32 and 64-bit drivers on CD-ROM
References
Product
USB alert modem
Models
COB03600000
Compatible with ThermoServer 4.2 and higher. Requires analog/PSTN telephone line (not a digital line).
43
OCEAVOICE – THERMOSERVER ALERTS VIA THE INTERNET
Your ThermoServer alarm management system can use the OCEAVoice(1)
service to send alert notifications via the Internet using Push Voice XML
technology.
Replacing a dial-up modem and associated analog telephone line, this
solution is a highly reliable, hassle-free and cost-effective way to send
voice messages, SMS texts and fax alerts from your Cobalt wireless
monitoring solution.
Features
..Secure transmission for voice, SMS and fax
..Worldwide coverage with 99.7% reliability,
..Telephone service handles key-press
..Redundant infrastructure, fully compliant
messages
acknowledgement, busy signals, and no
answer
..Uses the Internet without any modem,
24/7/365 service
with Disaster Recovery Plan requirements
..Easily modifiable, high quality voice
messages
dedicated phone line, or specific installation
References
Type
References
Annual service for 1,000 alerts
PRE10000000
Additional alerts
PRE11000000
(1) Requires ThermoServer 4.2 or higher.
No
installation
required!
44
Software
Management,
calibration, and
control over
your monitoring
modules.
Software
45
THERMOSERVER 5 - THERMOCLIENT 5
The ThermoServer-ThermoClient software suite(1) is the cornerstone
of the Cobalt wireless monitoring system. With the included Alert
Management System, these applications enable you to manage all
aspects of your installation, from configuring the wireless sensor network
and collecting sensor data automatically to generating reports and audit
trails.
An easy-to-use interface displays a visual dashboard so you can see
the status of your sensors at all times. The solution’s advanced alert
management system to notify you 24/24 if sensor readings exceed the
limits you define or if a technical problem occurs anywhere in the system.
The complete
companion
software suite
for your Cobalt
systems
ThermoClient 5
..Provides visual dashboard to monitor sensor
..Controls alert management system with call-
..Configures sensor reading and data transmission
..Generates reports, graphs, and audit trail
..Manages users, passwords, and access rights
..Simple executable file to run on unlimited
status and run on-demand reads
cycles
(compliant with FDA 21 CFR Part 11)
groups and day/night/weekend/holiday settings
(complies with FDA 21 CFR Part 11)
number of PCs (no installation process required)
46
ThermoServer 5
..Core services for the Cobalt monitoring system
..Transmits alerts in case of technical or limit alarms
..Collects data from Cobalt modules wirelessly
..Scalable solution handles nearly unlimited
..Includes SQL database and archive features
..Client-server architecture supports local network
..Compatible with OPC gateway(2)
..Cloud services also available(2)
and automatically
number of sensor end-points
(complies with FDA 21 CFR Part 11)
and Internet access
Alert Management System
..Watchdog software monitors all incoming sensor data
..Issues alerts in case readings exceed configured limits
..Supports automated voice calls, e-mail, SMS, printer,
fax, dry contact alarm devices, and wireless siren
..Fully compatible with OceaVoice Internet-based alert
solution
..Monitors proper operation of ThermoServer and alert
media
..Handles alert acknowledgement by users
References
Product
Sensors in system
Reference
1-20
LOG01050010
21-49
LOG01050020
50-99
LOG01050030
unlimited
LOG01050040
1-19
LOG02050010
20-49
LOG02050020
50-99
LOG02050030
unlimited
LOG02050040
ThermoServer 5 / ThermoClient 5
with Alert Management System
ThermoServer 5 / ThermoClient 5
with Alert Management System
& Cobalt M support
PC system requirements - one the following Microsoft® Windows® operating systems(3):
• Windows® Server 2012 (64 bits)
• Windows® Server 2008 and 2008 R2 (32 bits / 64 bits)
• Windows® Server 2003 (32 bits / 64 bits)
• Windows® 8 (64 bits)
• Windows® 7 (32 bits / 64 bits)
Compl
ie
with FD s
21 CFR A
Part 11
(1) Software provided in English and French. (2) Additional fee may apply.
(3) Please contact us for more details regarding server capacity.
47
THERMOCLIENT MOBILE FOR SMARTPHONES & TABLETS
ThermoClient® Mobile is a free(1,2), easy-to-use application that displays
the details of your OCEASOFT Cobalt™ wireless datalogging networks
right on your smartphone or tablet. ThermoClient Mobile connects
securely via the Cloud to your Cobalt system over the Internet or Wi-Fi so
you can check up on the latest sensor readings and settings, and monitor
alarms anytime and anywhere.
ThermoClient® Mobile is the perfect complement to your existing system,
giving you direct access to your remote sensors conveniently from your
iOS or Android device. Use ThermoClient Mobile to keep in touch with
your laboratory and storage facility sensors from home, work, and on the
go, and rest assured that your critical work is being monitored 24 hours a
day, every day.
Features
..Get mobile access to your Cobalt wireless
sensor networks from anywhere in the world
..Login securely to all your sites
..Access sensors with alarms directly
..Connect to our sample database using
ThermoClient Mobile in demo mode
..View latest data from sensors in your labs
and storage facilities
..For iOS® and Android® smartphones and
tablets
References
Product
References
ThermoClient Mobile for iOS®
ThermoClient Mobile for Android®
Contact us
(1) Software available in English and French. (2) Requires OCEACloud subscription.
Viewer apps for
Cobalt wireless
systems from
your iOS®
or Android®
device
48
THERMOCALIBRATION: SENSOR CALIBRATION KIT
This kit enables you to calibrate up to ten external digital or
analog temperature sensors simultaneously using OCEASOFT’s
specialized ThermoCalibration software and a reference sensor
that you may choose to have calibrated by our Cofrac (ISO/IEC
17025) accredited laboratory.
ThermoCalibration software automatically reads connected
sensors to calculate sensor uncertainty and determine compliance
using your own measurement points and preferred calculation
methods (normal, uniform).
Features and options
..Calibrated PT100 reference sensor and Cobalt
1 wireless module: high-precision PT100
(-100°C to +150°C; 0.05°C uncertainty), 4-wire,
class A
..USB wireless receiver to read reference
sensor
..10-sensor octopus cable with USB connector
..ThermoCalibration software(1) based on
digital standard interface API
• Calculates correction coefficients and
uncertainty
• Creates customizable calibration reports
• Automated control via RS-232 of Julabo
baths
(1.5 m)
References
Product
References
Thermo-Calibration software and
interface kit
Requires Windows XP® SP3 or
higher
LOG06021000
10-sensor USB “octopus” cable
COB07100002
PT100 Reference chain
COB#0512101
USB wireless receiver
COB#1500002
Complete
toolkit for
calibrating
your own
temperature
sensors
(1) Software available in French only.
49
THERMAL MAPPING
Compatible with the FD X 15-140 (or NF X 15-140) standard, this unique
thermal mapping system(1) enables you to characterize and qualify
temperature behavior within climate-controlled chambers such as
pharmaceutical freezers, refrigerators, and cold rooms. Simply place the
provided sensors inside the chamber and let the software create a 3-D
map for you.
Thermal mapping enables you to determine the regularity and stability
of temperature-controlled enclosures, and determine compliance or
non-compliance, so that you can manage storage zones in accordance
with your requirements concerning maximum permissible error. Among
other things, this enables you to identify temperature zones that are
compatible with your products, and to adjust equipment settings
accordingly.
Most clients prefer to set up Thermal Mapping independently from their
regular Cobalt wireless monitoring solution, though the software may
be used with your existing equipment. A turnkey solution is available,
complete with laptop computer, wireless receiver, all required software,
and configured wireless modules/sensors. Please contact OCEASOFT for
details on available options.
You don’t have time to do it yourself ?
If you don’t have time to deal with thermal mapping yourself,
OCEASOFT will be pleased to take care of it for you. Please contact us
for more information regarding 9- or 15-point mapping services, with or
without calibration, as well as quantity discounts.
Features and options
..OCEAMAP software (supports up to 15
sensors)
..FD X 15-140 (or NF X 15-140) compliant (reports,
targets, deviation, displays, control values, max.
regularity, max. stability, graphs, etc)
..Wireless receiver (ref. COB#1500002)
..ThermoServer (ref. LOG01042010)
..Carrying case
..9 or 15 temperature sensors and wireless
Cobalt digital or analog data-loggers with
optional calibration (Cofrac / ISO/IEC 17025)
References
Product
Thermal Mapping
Options
Please contact us
References
LOG05020000
(1) Software available in French only. Please contact us if you have specific thermal mapping needs.
Qualify
temperature
behavior
in climatecontrolled
chambers
50
Standalone
datalogging
Easy solutions
for tracking
temperature and
humidity.
Standalone datalogging
51
Emerald
The art of monitoring temperature
EMERALD - TEMPERATURE TRACKING WITH A SMARTPHONE
OCEASOFT Emerald brings temperature tracking right to your smartphone.
With its Bluetooth® Smart connectivity and small size, Emerald fits easily
into nearly type of container or enclosure. Set datalogging parameters
and view complete temperature readings and history wirelessly from your
smartphone from anywhere using the free EmeraldView smartphone app.
A simple solution for tracking temperature at a fixed location, Emerald
excels at mobile temperature tracking and data sharing via the Cloud.
Place Emerald inside a crate or package and use the app to check it at
different locations. Each time you read Emerald, the data – complete with
geolocation information from your phone – can be uploaded to the Cloud
and accessed from anywhere in the world.
Features
..Emerald wireless datalogging module with
colored ring, battery, and magnetic mount
..Internal sensor: 0°C to +50°C or -40°C to +85°C
External Pt100 sensor: -200°C to +200°C
..ISO/IEC 17025 (Cofrac) accredited or traceable
calibration available, please contact us
..Robust wireless access even inside trucks,
containers, and packaging
..Control and view Emerald modules with your
smartphone or tablet (iPhone 4S/5, iPad 3/4)
using free EmeraldView app
..Cloud access and viewing with free
EmeraldView PC software
..Long Bluetooth® Smart wireless range
(line-of-sight): up to 50 meters (164 ft.)
Works
with your
smartphone
and the Cloud
52
Emerald temperature module
Specific details
•
For temperature tracking in
mobile and fixed scenarios,
with wireless data download
and Cloud storage.
•
•
•
Temperature ranges: 0°C to +50°C,
-40°C to +85°C, -200°C to +200°C
Dimensions: Ø 5 x ≈2 cm (Ø 2 x ≈0.8 in.)
Protection: IP67 (internal), IP40
(external), replaceable rubber gasket(1)
Long battery life with user-replaceable
Lithium battery
References
(Emerald module + integrated or external temperature sensor)
Sensor type
# Sensors
Internal
External
(2)
Standard module
Range
1
0°C to +50°C
EMD50101110
1
-40°C to +85°C
EMD50102210
1
-200°C to +200°C
Accessories
Set of 5 colored rings
Aluminum grey
EMD00000000
Dark blue
EMD00100000
Green
EMD00200000
Gold
EMD00300000
Red
EMD00400000
Purple
EMD00500000
Black
EMD00600000
Yellow
EMD00800000
Light blue
EMD00900000
Set of 10 rings (all colors)
Lithium battery (5-pack,
includes 5 rubber gaskets)
EMD01000000
0°C to +50°C
-200°C to +200°C
EMD00000100
-40°C to +85°C
EMD00000200
QR code download link stickers for containers (50)
Vouchers for
Cloud access
EMD50203110
References
EMD01300000
5-9
EMD04000000
10-99
EMD04100000
100-199
EMD04200000
200-599
EMD04300000
600-999
EMD04400000
1,000 - 2,499
EMD04500000
2,500 - 9,999
EMD04600000
10,000 - 19,999
EMD04700000
20,000 - 49,000
EMD04800000
over 50,000
EMD04900000
(1) To maintain water-proof qualtities, we recommend replacing the rubber gasket when you
replace the battery. (2) Color rings not changeable on PT100 models.
53
LOGTAG
LogTag is a datalogging solution for measuring temperature and/or
humidity levels in a variety of environments, from laboratories and
food storage facilities to the transport containers for biological samples,
blood, organs, etc. Slightly larger than a credit card, LogTag stores several
thousand readings.
The included LogTag Analyzer software configures the module and
downloads data via a USB cradle. LogTag modules are available with
various sensor options. The internal temperature module also offers an
optional LCD display showing a 30-day summary.
Common features
..Datalogger with internal (LCD optional) or
..Multi-lingual software (EN, FR, IT, SP, DE, etc.)
..OK / Alert indicator LEDs
..Runs on any Windows PC
..Temperature ranges for various application
..IP65 for internal temperature modules, IP61
external sensor (resolution up to 0.1°C)
needs
..Programmable sampling frequency from 30
seconds to several hours
..Complies with EN 12830 cold-chain standard;
CE/CEM certified
and user guide (FR, EN)
for temperature/relative humidity module
and external sensors
..Operating range: -40 / +85°
..ISO/IEC 17025 (Cofrac) accredited calibration(
) available, please contact us
LogTag module options
Specific details
•
Standard LogTag module
with temperature or
temperature/relative
humidity sensor
Standard LogTag module
with temperature sensor and
LCD screen
•
•
•
•
•
•
module
Data collection, analysis, and
transfer kit
•
•
•
•
•
Internal temperature sensor: up to 8,000
readings
or
Dual temperature and relative humidity
sensor: up to 8,000 readings for each
Size: 86 x 54.5 x 8.6 mm; 35 g
Battery life ~2-3 yrs (must be returned
to OCEASOFT for battery replacement)
Internal temperature sensor module: up
to 7,770 readings
Size: 93 x 54.5 x 8.6 mm; 39 g
Battery life ~1 yr (replaceable by user)
Stores up to 8,000 readings (see table
below for available ranges)
Size: 86 x 54.5 x 8.6 mm; 39 g
Battery life ~2-3 yrs (return to
OCEASOFT for battery replacement)
LogTag Analyzer Software
USB cradle for data transfer and
programming
Includes 1 yr technical support
54
References
Options
Sensor
type
# Sensors Range °C
Temp +
humidity
1 internal
Notes
Standard
Temp: -40°C to + 80°C
RH: 0 – 99.9%
LTG01100100
-40 / + 85°C
LTG01010100
-30 / +60°C
1 internal
-80 / +40°C
Temperature
With LCD
-40 / + 99°C
(1.5 m cable)
LTG01010110
Up to 1,000
hours at -80°C
LTG01050100
Bare, non-food
LTG01020100
Steel
LTG01030100
Steel w/ handle
LTG01040100
Steel sensor
Module
operation:
-30 / +70°C
LTG01060120
(50 cm cable)
1 external
-80 à +40°C
LTG01060130
(3 m cable)
LogTag kits
Options
Additional kit
5
LTG01010300
Kit with LogTag
analyzer software
/ USB cradle
LTG02000200
LTG02000100
1
10
100+
LTG01010500
Standard
LTG01010400
Description
Kit with # LogTag module(s), with internal sensor,
1 yr tech support
LTG01010100
Please contact us regarding
quantity discounts.
Accessories
Description
Reference
3V Battery
Standard LogTag
LTG04000100
Wall-mount kit
LogTag with LCD
LTG04000110
LTG05000100
USB cradle(1)
For all LogTag modules
Convenient
creditcard sized
temperature
monitoring
Contact us
Protective casing
(1) Only available on as-needed basis as a replacement part
55
THERMO TRACER
ThermoTracer is a robust standalone datalogger designed to track
temperature conditions during product storage and delivery, notably
in climate-controlled and refrigerated areas, laboratories, blood and
pharmaceutical product handling, and food service facilities.
Several ranges and resolutions are available, supporting temperatures
as high as 125°C. The provided MySQL-based ThermoTracer software
enables you to program your dataloggers, download readings, and view
data graphs and tables
Features
..Datalogger with internal temperature sensor
..Unique serial number for each module
..Integrated battery (up to 5 years or 1 million
..For use with OCEASOFT’s ThermoTracer
readings), non-replaceable
..Temperature ranges and precision for various
application needs (see below)
..Programmable sampling frequency, start/
stop, alarm limits
..Complies with EN12830 cold-chain standard;
CE/CEM certified(1)
software (Windows XP or higher) and USB
connection kit
..Module size: 17 mm Ø; 3.3 g
..IP65 or IP68 (with protective casing)
..Made by Maxim (iButton)
..ISO/IEC 17025 (Cofrac) accredited calibration(1,
2)
Available sensors
Specific details
ThermoTracer 21G
•
•
•
•
•
ThermoTracer 21 (L or T)
•
•
-40°C to +85°C
Memory: 2,048 readings
Programmable reading from 1 to 255
minutes
Resolution 0.5°C
22L: -40° to +85°C
22T: 0°C to +125°C
Memory: 4,096 readings (resolution
0.0625°C); 8,192 (resolution 0.5°C)
Sampling rate from 1 s to 273 hrs
OCEASOFT
is a Maxim
Authorized
Software
Developer
56
References
Holder color
Options
Item
Green
Yellow
Red
Blue
Black
ThermoTracer 21G
TTR010
11010
TTR000
01010
TTR010
11030
TTR010
11040
TTR010
11050
ThermoTracer 22L
TTR010
21010
TTR010
21020
TTR010
21030
TTR010
21040
TTR010
21050
ThermoTracer 22T
TTR010
31010
TTR010
31020
TTR010
31030
TTR010
31040
TTR010
31050
ThermoTracer 22T
TTR000
01010
TTR000
01020
TTR000
01030
TTR000
01040
TTR000
01050
Credit-card
holder
IP68 shell
No holder
TTR010
11060
TTR010
11070
TTR010
11000
TTR010
21060
TTR010
21070
TTR010
21000
TTR010
31070
TTR010
31000
TTR000
01060
Software
License
Item
Description
1
Standalone computer
ThermoTracer software
+ USB interface
Client / server (server
computer with unlimited
client licenses)
2
3-4
5 or
more
LOG04031100
-10%
-20%
-30%
LOG04031110
Accessories (all models)
Description
Reference
IP68 waterproof protection
TTR00001070
USB interface(3)
TTR02501000
Velcro strip (2.5 m)
Male/female
TTR03001000
Male
TTR04001000
Female
TTR04001000
Remote software configuration and setup service
PRE03000002
(1) Certificates provided upon request. (2) Accuracy depends on target temperature. Please see
Calibration section for more details.(3) Only available to replace existing USB interface; requires
software license.
57
58
Services
OCEASOFT has the
expertise you need
to get the most out
of your monitoring
systems
Services
59
Services
Personal attention to help
you optimize your solution
SITE SURVEYS
Depending on the size and layout of your site, project planning may be
a detailed and complex process. In many cases, it is possible to determine
system requirements by studying the layout and target equipment to be
monitored using a floor plan or site map. Other sites may be optimized by
performing a complete site survey before ordering and installing products.
OCEASOFT will perform tests on-site to determine the best placement of
receivers and the optimal number of repeaters for reliable coverage. By
helping you choose the right equipment for your situation, surveys save
you time and money. Survey costs are deducted from the final cost of your
installation.
ooNo real additional cost to clients
ooSpeeds up deployment
ooRight-sizes wireless configuration
ooReduces overall system cost
Site surveys
before
installation
save you time
and money!
Please contact OCEASOFT or your authorized representative for more
information.
INSTALLATION
OCEASOFT data logging solutions are designed to be easy to install. However, depending the configuration,
site complexity and available technical resources, clients may choose to have OCEASOFT qualified technicians or
partners handle the installation process for them. We offer complete installation and set up services for:
ooOCEASOFT wireless and standalone products
ooSoftware and alert systems
ooLocal and wide-area networks using Cobalt supporting
infrastructure
Please contact us directly for a personalized quotation for installation
services, or contact your authorized OCEASOFT distributor.
References
Description
Reference
On-site installation and qualification of all
hardware and software. Rate based on site size
and complexity. Includes travel costs (France).
PRE03000001
Installation via remote Internet connection.
Includes installation report.
PRE03000002
Remote access
and remote set
up services
60
IQ/OQ EQUIPMENT QUALIFICATION
If you work in an environment governed by Good Manufacturing Practices (GMP) regulations, you are most
likely subject to external audits by authorities such as the Food and Drug Administration (FDA), European Food
Safety Authority (EFSA) or other local safety agencies. These audits, as well as your own commitment to a
Quality approach, include your monitoring equipment.
To ensure that your installation complies with requirements and specifications, OCEASOFT has elaborated a
series of Installation Qualification and Operational Qualification documents for its clients. These documents
may be customized for your specific situation, thereby guiding you through rigorous end-to-end Cobalt wireless
monitoring solution testing.
ooTest scenarios based on over 10 years experience in monitoring
ooAdapted to satisfy GMP/GLP requirements
ooIQ/OQ documents for your own use or with expert technical
assistance from OCEASOFT
We highly recommend you perform a complete Installation Qualification
and Operational Qualification procedure to ensure maximum system
reliability. Please contact us directly for a personalized quotation for IQ/OQ
services, or contact your authorized OCEASOFT distributor.
References
Description
Reference
IQ/OQ documents
PRE05000000
IQ/OQ assistance (includes 2 days assistance at
your site, with post-qualification follow-up by
OCEASOFT validation engineers)
PRE05000001
Installation and
Operational
Qualification
guidelines
for complete
system testing
61
MAINTENANCE AND SUPPORT CONTRACTS (COBALT)
The OCEASOFT team has unmatched expertise in assisting customers with
their monitoring, system and maintenance issues. OCEASOFT offers three
maintenance contract options – Basic, Silver, and Gold – to keep your Cobalt
wireless monitoring solutions up and running reliably over the long run.
We have found that the most effective way to serve customers is to connect
remotely to their system and troubleshoot problems directly. In order to benefit
from an OCEASOFT Technical Support Contract, you must allow restricted
remote access to your ThermoServer computer, used exclusively with your
simultaneous supervision and permission.
ooAll maintenance and support services are provided by experienced
and dedicated OCEASOFT technicians or authorized partners.
ooRemote connections for fast and direct service
ooBasic, Silver, and Gold levels to match your specific needs,
budgetary constraints, and installed solution.
Services
Remote
On-site
Basic
Silver
Gold
Hotline (2-hr callback), troubleshooting, problem analysis
X
X
X
E-mail technical support
X
X
X
Module configuration assistance
X
X
X
Downloads/tools/FAQs
X
X
X
Minor ThermoClient software upgrades
X
X
X
Replacement installation media CD-ROM if lost / damaged
X
X
X
Remote installation services
X
X
X
Annual preventive maintenance visit / functional checks
X
X
• Annual sensor calibration w/certificates, and software
configuration
X
X
• Battery change in all wireless modules if necessary
X
X
• Minor ThermoServer software upgrade
X
X
• Technical training on upgrades
X
X
• 25% discount off OCEASOFT training courses
X
X
(1)
Other
• Major ThermoServer software upgrades
X
• Database maintenance, data archive on CD/DVD
X
• Equipment loan if repair required
X
Up to 3 corrective maintenance visits per year
X
Server migration and major software upgrades
X
Warranty extension for duration of contract
X
Technical training
X
Duration (months)
12
36
36
(1) Digital sensors calibrated by standard exchange; analog sensors calibrated at customer site or by
return to OCEASOFT.
62
References
Item
Description
Reference
1 - 20 modules
With remote
access
Basic maintenance and support
Without
remote
Internet
access
PRE21600000
21 - 50 modules PRE21610000
51 - 100 modules PRE21620000
101+ modules
PRE21630000
1 - 20 modules
PRE21640000
21 - 50 modules
PRE21650000
51 - 100 modules PRE21660000
101+ modules
PRE21670000
Silver maintenance and support
PRE20800000
Gold maintenance and support
PRE20810000
Keep your
system running
reliably with
priority service
by qualified
technicians
For all three maintenance contract levels, pricing is based on your installed
monitoring equipment and site size. These contracts are designed to evolve
with site size and complexity. Please contact us for further information
regarding contract details.
REPLACEMENT PARTS
Miscellaneous spare parts and replacements are available for your OCEASOFT
products.
References
Item
Flat ribbon cable to pass sensor though
door/insulation for placement inside
enclosure (included w/new modules)
Batteries
Mounting kit
Description
Reference
3 wires, for single temperature sensor
COB03100000
4 wires, for dual temperature / humidity sensor
COB03200000
5-pack for Cobalt 1
COB03300000
Battery with connector for Cobalt 1
COB03500000
5-pack for Cobalt 2
COB03400000
Complete kit for Cobalt 1
COB06500000
Complete kit for Cobalt 2
COB06600000
Velcro® strip
COB0XXXXXX
63
HOSTED THERMOSERVER SOLUTION: OCEAHOST
Instead of installing and running ThermoServer, the software heart of your
Cobalt wireless monitoring system, on a dedicated server in your offices or
laboratory, you may subscribe to OCEASOFT’s ThermoServer hosting service
and keep your data safely on the cloud.
With this solution, your entire ThermoServer application, including its
MySQL database, is installed on a highly reliable server that is easily
accessible from any authorized location via the Internet. ThermoClient
software consists of one single file that you can easily install or copy on
your computer(s).
Hosting your ThermoServer software with OCEASOFT is an all-inclusive
package simplifies client responsibilities and increases reliability:
ooEliminates need for dedicated server computer, installation and
maintenance at your site
ooServer software upgraded automatically
ooIncludes data maintenance, backup and restore
oo99.9% reliable operation
ooSecure access for your monitoring staff and service technicians
With OCEAHost, you have no hidden or unexpected costs. Progressive
pricing is based on the size of your installed sensor network.
Oceahost solution architecture
References
Description
Oceahost
Reference
PRE09000000
Hosting your
ThermoServer
solution eliminates
on-site hassles
and maintenance
issues.
64
CALIBRATION / METROLOGY
Complete in-house calibration
services
OCEASOFT has an in-house ISO/IEC 17025-accredited laboratory to calibrate
a variety of sensors for different target ranges and applications. The
following calibration options are available, depending on the product type
and your requirements:
ooISO/IEC 17025: Official Cofrac(1) certification by the accredited
OCEASOFT laboratory for customers with specific quality
system requirements.
ooTraceable to Cofrac: OCEASOFT certification using a Cofraccalibrated reference chain
ooTraceable to NIST (2): OCEASOFT certification using a NISTcalibrated reference chain
Our sensors are typically calibrated by the OCEASOFT laboratory
before being shipped to customers. They are accompanied either by
an official Cofrac accredited certificate or an OCEASOFT certificate
(which is downloadable via the ThermoClient software directly). These
certificates contain individual correction parameters for use in OCEASOFT’s
ThermoClient software.
The OCEASOFT laboratory also offers both Cofrac-accredited and traceable
calibration services for non-OCEASOFT products. For this, customers must
provide the complete measurement chain. Please contact us for more
information.
External digital temperature and dual temperature/humidity sensors on
Cobalt 2 and Cobalt 1 modules may be recalibrated by standard exchange.
In this case, OCEASOFT sends you a new sensor and you return your old
sensor after swapping them at your site, which enables you to avoid downtime or traceability interruptions(3). PT100 sensors are generally recalibrated
at your site by a qualified technician. Sensor drift may also be calculated to
establish consistency over time for external temperature sensors.
(1) French National Accreditation
Committee, France. (2) National Institute
of Standards and Technology, federal
technology agency, United States. (3)
Standard exchange is only offered for
external digital sensors, as the entire
measurement chain is contained within
the sensor itself, independently of the
Cobalt module that transmits the signal
transparently. A decontamination certificate
is required.
(4) See related pages for specific product
details.
65
Calibration references(1)
Internal digital temperature modules
Expanded uncertainty(2) (k=2) generally observed after calibration: 0.3 to 0.5°C
Traceable to COFRAC or NIST
Product
Cobalt temperature
+10 /+50°C
Initial
(standard)
Specific
PRE01010503
1 point: 23°C
PRE01012303
1 point from
+10 to 50°C
COFRAC or equiv.
Std. Exchange
Additional
point
Customerdefined points
PRE01011903
PRE01010506
External digital temperature modules
Expanded uncertainty(2) (k=2) generally observed after calibration:
from 0.12 to 0.35°C (traceable); from 0.06 to 0.3°C (Cofrac)
Product
Initial
(standard)
Specific
Standard
Specific
standard
exchange
exchange
Cobalt
temperature
-40 / +80°C
PRE01010103
5 points:
-30, -15, 0,
20, 40°C
PRE
01012103
2-5 points
Cobalt
temperature
-40 / +120°C
PRE01010803
5 points:
+30, 60, 80,
105, 120°C
PRE
01012203
2-5 points
Cobalt
temperature
(contact)
-40 / +80°C
PRE01011703
5 points:
+0, 20, 40, 60,
80 °C
PRE
02010103
COFRAC or equiv.
CustomerAdditional
Std.
defined
point
Exchange
points
PRE
02012103
PRE
02010104
PRE
01011903
PRE
02010803
PRE
01010104
PRE
02012203
PRE
02010804
PRE
02011703
External dual digital temperature / humidity modules
Expanded temperature uncertainty(2) (k=2) generally observed after calibration: 0.3 to 0.5°C (between +5 and
50°C). Expanded temperature uncertainty(2) (k=2) generally observed after calibration: 3 to 4% (between 10
and 90% RH) and 1 to 2% (COFRAC)
Product
Cobalt
temperature
/relative
humidity
Initial
(standard)
Specific
Standard
Specific
standard
exchange
exchange
PRE0
1021903
PRE01020403
1 point 23°C,
50% RH
COFRAC or equiv.
CustomerAdditional
Std.
defined
point (pair)
Exchange
points
PRE
01022703
PRE
01022703
PRE
02022703
Between 10
to 50°C and
10 to 90%
RH
PRE
01020406
PRE
02020406
(1) See related pages for specific product details. (2) Expanded uncertainty without correction.
66
External PT100 analog temperature modules
-200/+50°C: Expanded uncertainty(2) (k=2) generally observed after calibration: 0.1 to 0.3°C
-100/+150°C: Expanded uncertainty(2) (k=2) generally observed after calibration: 0.07 to 0.2°C
+100/+350°C: Expanded uncertainty(2) (k=2) generally observed after calibration: 0.4 to 0.9°C
Traceable to Cofrac or NIST
Product
PT100
-200/+50°C
PT100
-100/+150°C
PT100
100/+350°C
Initial (standard)
Specific
PRE01011503
3 points: -196, -80, 0°C
contact us
PRE01010303
3 points: -80, -40, 0°C
PRE
01012403
(2-5 points)
PRE01011003
3 points: 100, 200,
350°C
PRE
01012503
2-5 points
Cofrac
Additional point
Customer-defined
points
PRE01011504
PRE01011903
PRE01010304
PRE01011006
External dual digital temperature / CO2 modules
Expanded uncertainty(2) (k=2) generally observed after calibration: 0.3 to 0.5°C
Expanded uncertainty(2) (k=2) generally observed after calibration: 0.4 to 0.5°%
Product
Cobalt digital
temp / CO2
Initial
(standard)
Specific
Standard
Specific
standard
exchange
exchange
PRE01030603
37°C,
5 %CO2
Cofrac
Additional
point
(pair)
Customer-defined
points
PRE
01030606
Contact us
Differential pressure
Expanded uncertainty(2) (k=2) generally observed after calibration: 3 - 4 Pa
Traceable to Cofrac
Product
Cobalt diff.
pressure
Initial (standard)
Specific
Additional point
PRE01081103
5 points: 0, 10, 20, 30, 60, 100 Pa
PRE01052703
PRE01051903
67
4-20 mA modules
Expanded temperature uncertainty(2) (k=2) generally observed after calibration: 0.1 to 0.2 mA
Product
Cobalt 4-20 mA
Initial (standard)
Specific
Std.
Exchange
PRE01091203
4, 8, 12, 16, 20 mA
Specific
Std. Exchange
Additional point
Contact us
Cobalt M
Expanded temperature uncertainty(2) (k=2) generally observed after calibration: 0.3 to 0.5°C
Product
Cobalt temperature
-30°C à +50°C
Initial
(standard)
Specific
PRE01011603
3 points: -25,
+5, +25°C
PRE01012803
1 point from
-30°C to +50°C
Standard
exchange
Cofrac
Additional
point
PRE01011903
PRE01010506
Emerald
Incertitude de mesure :
Capteurs internes de température : Incertitude élargie(2) (k=2) généralement observée après étalonnage: entre 0.3°C et 0.5°C
Capteurs externes de température : Incertitude élargie(2)(k=2) généralement observée après étalonnage: entre 0.2°C et 0.5°C
Rattaché ou NIST
Produit
Initial (standard)
Emerald internal
probe
PRE01013103
1 point: +23°C
PRE01013203
1 point: +5°C
Emerald external
probe
PRE01013403
1 point: -80°C
PRE01013503
1 point: -196°C
Spécific
PRE01013303
1 point: -30°C
PRE01013603
Customer 1 defined
point
PRE01013703
Customer 1 defined
point
Cofrac
PRE01013604
PRE01013704
68
LogTag
Expanded temperature uncertainty(2) (k=2) generally observed after calibration:
Internal temperature sensors: 0.3°C to 0.5°C
External temperature sensors: 0.2°C to 0.5°C
Dual temp / RH sensors: 3% to 4% RH
Product
Initial (standard)
Specific
Additional point
PRE01015003
1 point: 5°C
PRE01015103
1 point from -25 to +60°C
PRE01015203
From -25 to +60°C
PRE01015006
PRE01025003
1 pair: 23°C / 50%
RH
PRE01025103
1 pair from 5 to 45°C
and 10 to 90% RH
PRE01025203
Pair(s) from 5 to 45°C
and 10 to 90% RH
PRE01025706
PRE01015403
2 - 5 points from
-40 to +99°C
PRE01015503
From -40 to +99°C
PRE01015304
Internal
temperature
sensor
Internal
temp/RH
sensor
External
PRE01015303
temperature
5 points:
sensor
-30, -15, 0, 20, 40 °C
External
temperature
sensor
(-80°C)
Cofrac
PRE01015603
3 points: -80, -40,
0°C
PRE01015604
ThermoTracer (iButton)
Expanded temperature uncertainty(2) (k=2) generally observed after calibration:
21G: 0.3 to 0.6°C
22L: 0.06 to 0.3°C
22T: 0.06 to 0.5°C
Product
Cofrac
Initial (standard)
Specific
Additional
point
DS1921G
-40/85°C
PRE01017003
-30, -15, 0, 20, 40°C
PRE01017103
2-5 points from -40 to +85°C
PRE01017203
PRE01017004
DS1922L
-40/85°C
PRE01017303
-30, -10, 0, 25, 40°C
PRE01017403
2-5 points from -40 to +85°C
(-10° and +24°C required)
PRE01017503
PRE01017304
DS1922T
0/125 °C
Contact us
PRE01017604
Required: +25,
+60°C
69
Non-OCEASOFT products
Product
Initial
(standard)
3rd-party
temperature
sensor
Specific
Cofrac
Additional
point
PRE01019003
Additional
point
PRE01019004
Drift calculation
Please send us the sensors accompanied by a decontamination certificate as well as the previous OCEASOFT
calibration certificate number.
Product
Initial (standard)
Temperature sensor
PRE14010103
Dual temperature/humidity sensor
PRE14020403
70
Sales
information
Sales information
71
OCEASOFT
Sales & contact information
ABOUT OCEASOFT
OCEASOFT is an international leader in temperature tracking systems
whose products and services help protect valuable biological samples,
vaccines, blood, food and other sensitive items from undesired or
unexpected variations in ambient storage and delivery conditions. Every
day, thousands of people rely on OCEASOFT hardware and software
solutions to monitor their laboratories, clinics, warehouses, transportation
equipment, and more.
OCEASOFT’s mission focuses on enabling customers to rest assured that
the physical parameters that matter most to them are being watched over
constantly. In today’s regulatory context, and with the high cost of lost
time and effort, our challenge is to reliably track key information, create
complete audit trails, and, with the Cobalt Monitoring System, alert you
in time to react in case something goes wrong with your lab equipment or
storage conditions.
ACCREDITATIONS / COMPLIANCE
An important part of providing quality service and products to customers
involves adhering to a variety of national and international regulations,
as well as internal quality and organizational aspects. OCEASOFT has
earned certifications and accreditations from the following major bodies
worldwide:

RoHS
2002/95/EC
Complies
with FDA
21 CFR Part 11
72
WHERE TO BUY
Region
Details
France
You may buy directly from OCEASOFT. Our products are also available
from authorized agents and distributors. Check www.oceasoft.com for
more information.
Europe
Check the list of distributors and agents on our web site
www.oceasoft.com
Asia/Pacific
North America
South America
Please contact us ([email protected])
CONTACTING OCEASOFT
For sales and product information, please feel free to contact us by any of
the following means:
E-mail
Telephone
Fax
Our postal
address
[email protected]
+33 (0)4 99 13 67 30
from 9:00 AM to 12:30 PM and from 2:00 PM to 5:30 PM CET
+33(0)4 67 42 84 13
OCEASOFT SAS
126 rue Emile Baudot
34000 Montpellier, France
73
SHIPPING
OCEASOFT products can be shipped nearly anywhere. We keep a large
quantity of products in stock in order to meet your needs as quickly as
possible. Products that require assembly and calibration may take longer to
deliver.
References
Region
Reference
France (continental)
Europe
Asia/Pacific, North America
PRE08000000
Please contact OCEASOFT or your authorized sales representative for
more information ([email protected])
PRODUCT WARRANTY
OCEASOFT products are covered by a Limited Warranty. Warranty service
for eligible repairs is available at no charge during the warranty period,
excluding shipping costs, starting on the date of invoice. Products under
warranty must be returned to OCEASOFT for repair.
..Cobalt products are covered by the Limited Warranty for a period of
two years
..ThermoTracer and Logtag are covered by the Limited Warranty for one
year.
Please do not hesitate to contact OCEASOFT for more information on
Warranty coverage, out-of-warranty repairs, and replacement parts.
COPYRIGHTS
© 2014 OCEASOFT. All rights reserved. OCEASOFT, the OCEASOFT
logo, Cobalt, Cobalt M, Cobalt T, OCEASOFT Emerald, ThermoServer,
ThermoClient, ThermoTracer, OceaHost, and OceaVoice are the exclusive
property of OCEASOFT. All other brands mentioned are the property of
their respective owners. OCEASOFT has made every effort to provide
accurate information in this catalog, but details are subject to change
without notice. The photographs, images, and drawings in this catalog are
non-contractual.
74
PRODUCT NOTICES
Safety notice
IMPORTANT NOTE: Do not use OCEASOFT products for protection or as part
of automated emergency system or as for any other application that involves
protecting people and/or property. Customers and users of OCEASOFT products
are responsible for making sure that the product is fit for the intended usage.
Do not open the product casing and do not disassemble or modify internal
components in any manner. OCEASOFT products do not contain any internal
components that require user intervention or repair. If the device shows signs
of improper operation, disconnect it immediately from its power source and
contact OCEASOFT technical services.
USB receivers
All OCEASOFT USB products and drivers are tested thoroughly. However,
it is not possible to test and qualify all computers and configurations. Our
experience has shown there are some variations in USB implementations
by computer manufacturers. It is therefore important for users to avoid
unnecessary risk by testing the products and validating processes internally to
ensure stability and reliability of USB communications in their environment.
Disclaimer and limitation of liability
OCEASOFT assumes no responsibility for any loss or claims by third parties
which may arise through the use of the products or services described in this
catalog. This document is non-contractual and subject to change without
notice.
OCEASOFT and its distributors shall not be held responsible either directly
or indirectly for cost, damage, expenses and legal fees, or personal injury
related to the use of OCEASOFT products, even in the case of faulty design or
manufacturing of said products. OCEASOFT products, including accessories and
replacement parts, are provided as-is without any additional warranty, explicit
or implied, with respect to files, their suitability for a particular application,
their quality, their commercialization or any other related aspect.
The seller’s and creator’s liability with respect to the product warranty is strictly
limited the amount paid by the client for said product. Under no circumstances
shall the seller or creator assume responsibility for any damage or prejudice
whatsoever, direct or indirect, specific or consequential, particularly with
respect to any down-time, loss of data, or any other financial loss resulting
from the use or impossibility to use the products, even if OCEASOFT is aware of
the potential occurrence of said prejudice. The product seller and creator advise
each product user to verify the results of using these files, and neither the
seller nor the creator shall be held liable for any damage related to using the
delivered product. OCEASOFT informs all future buyers and user of its products
that without the above limitations, OCEASOFT products would not be able to
exist.
75
GLOSSARY
Alarm
Anomaly condition reported by an end-point when a sensor
exceeds allowed bounds (i.e. temperature too low, CO2 level too
high, etc.) or in case of failure.
Alert
Notification that is sent to a user or group of users when an
alarm is reported by an end-point module.
Client
The software application for solution configuration and
everyday monitoring and reporting tasks.
Datalogging
The process of using an electronic device to record data from a
built-in or external sensor over time.
End-point
Wireless module that logs sensor data on a regular basis and
transmits it to the server.
ISM bands
License-free wireless frequencies for Industrial Medical Scientific
applications around the world.
Network
Computer workstations connected with servers, typically via
TCP/IP. Networks can be “local” (LAN) within a specific area
or building, or “wide area” (WAN), covering geographically
separated locations.
Receiver
Device that collects readings from end-point modules.
Connected to the server computer either directly via a USB port
or networked via TCP/IP.
Repeater
Device that transparently relays the wireless signal from more
distant devices.
SDP
Service Discovery Protocol, wireless technique used to
automatically add new devices to the wireless sensor network.
SEA
Spontaneous Emission of Alarms, a Cobalt feature that notifies
selected individuals or groups when an alarm condition is
detected on an end-point module or receiver.
Sensor
Electronic device that measures physical ambient parameters
such as temperature, humidity, or CO2 level.
Server
Computer configured with one or more receivers to collect
sensor data from end-point modules. The database and alarm
management system both reside on the server.
PTFE
Polytetrafluorethylene: Polymer with remarkable insulation
properties (temperatures up to +380°C) and protection from
humidity.
76
NOTES
77
NOTES
78
NOTES
79
www.oceasoft.com
80
November 2015
OCEASOFT SA
720 rue Louis Lépine
Millénaire
34000 Montpellier
France

our catalog

Transcription

Similar documents

Lead Manager Sell Sheet

Wireless Sensor Troubleshooting Guide

Two forces working with the weather…

iSCOUT PRS80

The idea with modifying stock down pipes is to gut the pre

Untitled

ASSURANCE - Sensaphone

A laboratory exercise introducing students to the Pourbaix for cobalt

THERMOMATIC EC HOME®

PR-32 Pressure Recorder