Banta CONTROLS

Comments

Transcription

Banta CONTROLS
CONTROLS - THROTTLE & ACCESSORIES Banta
UNIVERSAL ACCESSORIES UNIVERSAL ACCESSORIES
Part#
O.E.M
295-006
Universal
Application
O.E.M
295-196
Sold in multiples of 10
Application
Cable Clip
For 3/4″ tube handles.
Fits 3/16″, 7/32″ & 1/4″ conduit sizes.
No screws required, heat treated spring steel.
3/16″ Conduit (50 foot roll)
Single wound galvanized conduit.
(Use with our 295-055 Inner wire)
295-014
Part#
295-311
Universal
MTD# 726-0178
MTD# 725-0157
Sold in multiples of 10
7/32″ Conduit (50 foot roll)
Single wound galvanized conduit.
(Use with our 295-063 Inner wire)
Cable Clip
For 7/8″ tube handles. Hold all sizes of
conduit or two separate cables.
No screws required, heat treated spring steel.
295-048
295-261
Universal
Deluxe 3/16″ Conduit (50 foot roll)
Vinyl covered and plastic lined
conduit. The ultimate in galvanized
conduit. Black polyethylene outside
wrap with clear polyethylene liner.
Reduces friction - smooth action, provides weather seal corrosion resistance. (Use with our 295-055 Inner wire).
295-055
Universal
B&S# 220796
Sold in multiples of 10
Conduit Clamp
Special metal tab for non-rotation. Holds conduit to engine.
295-279
B&S# 22372
Sold in multiples of 10
Conduit Clamp
Dual or Single cable application. Accommodates any size
conduit. Made of plated steel with one 7/32″ diameter hole.
295-106
Sold in multiples of 10
Inner Wire (100 foot roll)
Copperized inner wire for
our 3/16″ Conduit cable.
Wire diameter: .056″
(Use with our 295-006 and 295-048 Conduit)
Conduit Clamp
Dual cable application. Accepts 3/16″ thru 7/32″ conduit.
Ideal for securing two conduit with one bolt.
295-063
Conduit Clamp
Single cable application.
Accepts 3/16″ thru 7/32″ conduit.
Squeeze type clamp holds conduit securely.
295-249
Universal
Inner Wire (100 foot roll)
Copperized inner wire for our 7/32″
Conduit cable. Wire diameter: .072″
(Use with our 295-014 Conduit)
295-097
425-157
UNIVERSAL
Sold in multiples of 5
290-015
7/32″ Conduit Button
Allows easy assembly of conduit to
control head. (For use with our 295-014 Conduit)
295-295
Throttle Control
48″ length, all steel construction.
Can be mounted on bow
or ″T″ handles. Negative action.
Conduit Length: 43-1/2″,
Inner Wire: 48″, Wire Travel: 1-1/2″
Sold in multiples of 10
Wire Stops
Hex body - wire stops with screws.
Ideal for securing inner wire at the engine end.
295-287
290-288
Sold in multiples of 10
Wire Stops
Swivel wire stops with screws. Ideal for securing control
inner wire to engine governor. Fits 1/4″ diameter holes.
C
Sold in multiples of 50
Cable Ties
Nylon 8″ cable ties with max.
Bundle diameter of 2″.
Ideal for securing controls to mower handles.
Self locking heads with uniform serrations.
Sold in multiples of 5
3/16″ Conduit Button
Allows easy assembly of conduit to control head.
(Use with our 295-006 and 295-048 Conduit)
295-105
Sold in multiples of 10
Throttle Control
71″ length, all steel construction.
Can be mounted on bow
or ″T″ handles. Negative action.
Conduit Length: 66-1/2″,
Inner Wire: 71″, Wire Travel: 1-1/2″
20-01
C
Banta CONTROLS - THROTTLE & ACCESSORIES
UNIVERSAL
Part#
UNIVERSAL
continued
O.E.M
Application
Part#
continued
O.E.M
Application
290-064
290-004
Throttle Control
53″ length, all steel construction
with plastic case and ″T″ handle,
positive action control. For centre
or side mounting with hole for 1/4″ bolt.
Conduit Length: 51″, Inner Wire: 53″,
Wire Travel: 1-1/2″
Throttle Control
74″ length, all steel construction,
no detents. Positive action control
with ″Z″ bend, mounting holes on 2″ centres.
Conduit Length: 72″, Inner Wire: 74″,
Wire Travel: 1-7/8″
290-002
290-296
*OUR MOST POPULAR*
Throttle Control Universal design
- Converts from positive to
negative action
- 1/4″ bolt handle bar mount
- 71″ conduit
- 76″ inner wire
- 1-5/8″ wire travel
- Plastic conduit cuts easily to replace application listed
below.
- Adjust control to full position (+ = longest, - = shortest)
for innerwire measurement
Throttle Control
71″ length, all steel construction
with plastic case and ″T″ handle,
positive action control. For centre
or side mounting with hole for 1/4″ bolt.
Conduit Length: 69″, Inner Wire: 71″,
Wire Travel: 1-1/2″
290-080
Throttle Control
53″ length, all steel construction
with aluminum cover plate.
Positive action control,
can be mounted on panel or
bolted through 1/4″ centre hole.
Conduit Length: 48″, Inner Wire: 53″,
Wire Travel: 1-1/4″
OEM#
290-023
Throttle Control
55″ length, deluxe all steel
construction. Positive action
control, side mount. Comes complete
with wire swivel, adjustable friction steel washer.
Conduit Length: 51-1/2″, Inner Wire: 55″,
Wire Travel: 1-1/4″
290-106
Throttle Control
Used on AYP (Roper/Sears),
MTD, NOMA, MURRAY and
others. 67″ length, all plastic
control with galvanized inner wire.
Can be mounted on bow or ″T″ handle.
Conduit Length: 60″, Inner Wire: 67″,
Wire Travel: 1-3/8″
290-155
Throttle Control
Panel mount control,
right hand version.
Used on Riding mowers, Tractors and self propelled
mowers. 48″ length, all steel control with ″T″ handle.
Conduit Length: 48″, Inner Wire: 60″, Wire Travel: 1-5/8″
290-163
Throttle Control
Panel mount control, left hand
version. Used on Riding mowers,
Tractors and self propelled mowers.
48″ length, all steel control with ″T″ handle.
Conduit Length: 48″, Inner Wire: 60″, Wire Travel: 1-5/8″
C
JOHN DEERE
AM115246
LAWN BOY
684693
MURRAY
42096
42775
42877
42878
42949
NOMA
52061
52769
ROPER / SEARS
107701X
111274X
111903X
111930X
TORO
27-6500
28-4810
28-6170
28-6740
29-9610
29-9612
33-2530
33-2531
33-2532
33-2533
33-2534
33-2535
33-2536
40-5520
40-5521
40-5522
40-5523
40-5524
40-5525
40-5526
53-7831
20-02
Conduit
Length
Action
Innerwire
Extension
53-3/8″
+
2-1/4
52-1/2″
+
1-1/2″
41-1/4″
42-1/2″
41-1/4″
47-1/2″
39″
+
+
+
+
+
2″
2″
2″
2″
2″
46-1/2″
46-1/2’
+
+
1-1/2″
1-1/2″
43″
47″
44″
65-1/8″
+
+
+
+
2-1/4
1-3/4
2″
2-1/8″
42″
54-1/2″
59″
38″
44-1/2″
44-1/2″
38″
42″
59″
49″
54-1/2″
39-1/2″
62″
42″
38″
54-1/2″
62’
45″
49-1/2″
35-1/2’
46-1/2″
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
2″
2″
2″
2″
2″
2-1/8″
1-7/8″
1-7/8″
1-7/8″
1-7/8″
1-7/8″
1-7/8″
1-7/8″
1-7/8″
1-7/8’
1-7/8″
1-7/8’
1-7/8″
1-7/8″
2″
3-7/8″
C
CONTROLS - THROTTLE & ACCESSORIES Banta
UNIVERSAL
Part#
O.E.M
ARIENS
continued
Application
290-006
Throttle / Choke Control
(Universal)
Light duty dash mount control
for throttle, choke and others.
This locking control is easy to install. Installation hole: 9/16”
diameter. Versatile locking control eliminates vibration
problems. Max push load: 10 lbs, Max pull load: 25 lbs.
Conduit length: 92-1/2”, Inner wire diameter: .060”
290-008
Part#
O.E.M
290-112
69080
06908000
290-148
Throttle Control
This heavy duty non
rotational locking
control has a variety
of industrial uses.
By turning ″T″ knob ¼ turn, control locks securely against
spring tension and vibration. Installation hole: 9/16″,
Max push load: 20 lbs, Max pull load: 50 lbs,
Conduit length: 92-1/2″, Inner wire diameter: .080″,
Conduit size: 1/4″
Application
Throttle Control
Found on Ariens, Murray / Noma snowblowers.
Conduit length: 30-1/4″, Inner wire length: 33″, Conduit
size: 3/16″, Inner wire size: .055″, Wire travel: 1-3/4″.
295-410
Choke / Tthrottle Control
(Universal)
Economical dash control for
choke, throttle and others.
This panel mount control is easy to install. Installation hole:
13/32” diameter. Max push load: 10 lbs, Max pull load: 25 lbs.
Conduit length: 95”, Inner wire diameter: .060”,
Conduit Size: 3/16”.
continued
75019
Bolens# 1719268
Troy Bilt# 9212
″T″ Control Knob
Fits most control heads.
Fits our 290-320 and 290-338 throttle and others.
290-328
69032
Throttle Control
Fits Snowblower models:
10954, 10962, 10965,
10969 and 10970.
Negative action ″F″ to ″S″, bracket for side mounting.
Conduit Length: 27-1/8″, Inner wire length: 29″,
Wire travel: 1-3/4″
285-483
06900011
290-105
Throttle Control
Economy Push Pull control for engine speed or choke
control. Fit many types of equipment, including Bobcat.
Positive action control. Conduit length: 60″,
Inner wire length: 63″, Wire travel: 2-3/4″
ARIENS
290-320
69087
Traction control cable
For Ariens snowblowers.
Fits models: 926001 / 002 / 003 / 004 / 005 / 006 / 007 /
008 / 009 / 010 / 011 / 012 / 013 / 014 / 015 / 016 / 017 /
021 / 022 / 023 / 024 / 025 / 026 / 027 / 101 / 102 / 103 /
300 / 301 / 302 / 303 / 304 / 305 / 306 / 307 / 308 / 310 /
311 / 312 / 313 / 314 / 315 / 316 / 500 / 501 / 502 / 504.
Overall Adjustable Length: 38-1/2″ to 39-1/4″,
Coil Length: 4-1/4″ (Adjustable end),
Coil Length: 4-5/8″ (fixed end).
285-484
06900012
Throttle Control
Fits rear engine Riders with
Tecumseh engines. Vinyl wrapped conduit.
Conduit length: 38-7/8″, Inner wire length: 39-7/8″,
Wire travel: 1-1/2″ (Use with our 295-410 ″T″ control knob)
290-338
69127
Throttle Control
Fits 1980 and up 28″, 30″ and
32″ rear engine Riders with
Briggs and Stratton engines.
Vinyl wrapped conduit.
Conduit length: 44-7/8″,
Inner wire length: 46-7/8″,Wire travel: 1-1/2″
(Use with our 295-410 ″T″ control knob)
C
Clutch blower control cable
For Ariens snowblowers.
Fits models: 926001 / 002 / 003 / 004 / 005 / 006 / 007 /008
/ 009 / 010 / 011 / 012 / 013 / 014 / 015 / 016 / 017 / 021 /
022 / 023 / 024 / 025 / 026 / 027 / 101 / 102 / 103 / 300 /
301 / 302 / 303 / 304 / 305 / 306 / 307 / 308 / 310 / 311 /
312 / 313 / 314 / 315 / 316 / 500 / 501 / 502 / 504.
Overall Adjustable Length: 25-1/4 to 26″,
Coil Length: 4-1/4″, Eyelet hole ID: 1/4″.
20-03
C
Banta CONTROLS - THROTTLE & ACCESSORIES
ARIENS
AYP
continued
Part#
O.E.M
285-485
06900018
Application
Chute control cable
For Ariens snowblowers. Fits models: 921001 / 002 / 003 /
004, 921300 and 921301, 926016 / 017 / 021 / 022 / 023 /
302 / 310 / 311 / 312 / 313 / 314 / 315 / 316 / 500 / 501 etc.
Measures: 61-3/8″ Overall Length, Wire Travel: 5-3/8″,
Eyelet hole ID: 1/4″.
285-486
06900019
Chute control cable
For Ariens snowblowers.
Fits models: 921002 / 003 / 004, 301, 926001 / 002 / 003
/ 004 / 005 / 006 / 007 / 008 / 009 / 010 / 011 / 012 / 013
/ 014 / 015 / 016 / 017 / 021 / 022 / 023 / 101/ 102 / 103 /
300 / 301 / 302 / 303 / 304 / 305 etc.
Measures: 54″ Overall Length, Wire Travel: 2″,
Both Ball Ends: 1/4″ diameter.
285-487
AYP
700417
Throttle Control
48″ length, plastic construction.
Can be mounted on bow or ″T″ handles.
Fits 20″ & 22″ side and rear discharge mowers.
Conduit Length: 48″, Inner Wire: 49-1/2″
290-079
851462
Throttle Control
For 20″ walk behind mowers,
1997 and later.
Conduit Length: 63-1/2″,
Overall Length: 68″
285-003
O.E.M
285-701
110675X
Application
Clutch Cable
Fits on Tillers.
46-5/8″ Conduit length X
51-1/2″ Cable length.
285-001
169676
175067
192413
Deck Engagement /
PTO Cable
Fits on many riders built by AYP.
Found on 42″ riders; also replaces AYP# 192413 found
on Sears model YT3000 (model 942-605911), 22 Hp with
42″ cut. Fits LT16542, LT18542, LT18542A, LT18542B,
LTH1342, LTH1342A, LTH1342B, LTH1342C, LTH1742A,
LTH1742B, LTH1742C, LTH1742D, LTH18542A,
LTH18542B, LTH18542C, LTH2042A, LTH2042B,
LTH2042C, YTH130, YTH1842A, YTH1842B, YTH1842C.
Conduit Length: 32″, Cable Length: 45″
285-000
435111
408714
197257
Deck Engagement / PTO Cable
Fits on many riders built by AYP. Found on 38″ & 42″ riders.
Fits CT126, LTH1438, LTH1538, LTH18538, YT16542 and
YT1942. Length: 69″
285-008
169676
175067
Deck Engagement /
PTO Cable
Found on many riders built by
AYP. Fits LT16542, LT18542,
LT18542A, LT18542B,
LTH1342, LTH1342A,
LTH1342B, LTH1342C, LTH1742A, LTH1742B, LTH1742C,
LTH1742D, LTH18542A, LTH18542B, LTH18542C,
LTH2042A, LTH2042B, LTH2042C, YTH130, YTH1842A,
YTH1842B, YTH1842C. Conduit Length: 32”,
Overall Length with Spring: 45-1/2”, Spring Length: 6”.
285-560
428311
130861
Zone Control Cable
For 22″ walk behind push
mower model PP751.
Die cast Z-bend on both ends.
52″ Conduit length X 59-3/16″ Cable length.
C
Part#
06900313
Traction control cable
For Ariens snowblowers.
Fits models: 921001 /
002 / 003 / 004 / 005 / 006 /
007 / 008 / 009 / 300 / 301 / 302 / 303 etc.
Measures: 24-5/8″ Overall Length,
Both Eyelet holes: 5/16″ ID.
290-018
continued
Chute Control Cable
For AYP / Craftsman /
Husqvarna / Sears snowblowers. Models 2009 on.
(Includes a heat resistant conduit cover = 14″ long approximately).
Measures: 45-3/4″ Overall Length, Conduit Length:
31-3/4″, Wire Travel: 11-3/4″.
20-04
C
CONTROLS - THROTTLE & ACCESSORIES Banta
AYP
AYP
continued
Part#
O.E.M
285-562
428274
Application
Chute Control Cable
For AYP / Craftsman /
Husqvarna / Sears snowblowers. Models 2009 on.
Measures: 46-1/2″ Overall Length, Conduit Length:
32-7/8″, Wire Travel Adjustable: 11″ thru 11-3/4″.
285-564
178674 / 198475
420673 / 421164
Chute Control Cable
For AYP / Craftsman / Husqvarna / Sears snowblowers.
Cable only. Measures: 59-1/4″ Overall Length, Conduit
Length: 50-3/4″, Inner Wire Length: 57-1/2″, Wire
Travel: 3″, Eyelet hole ID: 5/16″ with a Cast Z-Bend on the
other.
285-009
133107
Application
Husqvarna# 532 13 31-07
Zone Control Cable
For AYP built walk behind push mowers
(1999 thru 2004). Die cast Z-bend on both ends.
Conduit length: 56” X Cable length: 62”.
285-691
176556
Husqvarna# 532 17 65-56
Zone Control Cable
For AYP built walk behind push mowers built 2006 thru
2010. Fits models: PO500N21R, PR160N21CHC,
PR4N22SHA, PR550N21RH3, WM500N21R
and XT625N21RN3. Die cast Z-bend on both ends.
Conduit length: 46” X Cable length: 52”.
285-692
183281
Husqvarna# 532 18 32-81
183567
Husqvarna# 532 18 35-67
193235
Husqvarna# 532 19 32-35
Zone Control Cable
For AYP built walk behind push mowers (2005 thru 2010).
Fits models: 5521CHV, 5521RS, 52522SH, 6522SL,
65021CHV and 214502X83E, 319611X83E, 219611X83E,
37611, PH65Y21RHP, PR160Y21RPC, PR173Y22RP,
PR600T21RHP, PR600Y21RHPX, PR600Y21RHP,
PR600Y22RHP, PR625Y22RHP, PR625Y22RHPX,
PR7R21A, PR7R21B, PR7R21C, XT600Y21RP,
XT625Y22SHP. Die cast Z-bend on both ends.
Conduit length: 53-1/2” X Cable length: 59-1/2”.
156577 / 156581 / 168552
285-694
407816
Husqvarna#
532 40 78-16
194653
Husqvarna# 532 19 46-53
Control Cable
Drive Control Cable.
Found on AYP / Husqvarna / Sears / Craftsman mowers.
Conduit Length: 55”, Overall Length: 67”.
Heavy “Z” bend on one end, ball on the other.
C
285-690
285-693
Control Cable
Engine Brake Control Cable.
Conduit Length: 54″, Inner Wire Length: 60″,
Wire travel: 6″, Heavy ″Z″ bend on each end.
285-010
O.E.M
Zone Control Cable
For AYP built walk behind push mowers (2005 thru 2010).
Fits model: 212310X83E. Die cast Z-bend on both ends.
Conduit length: 46-1/2” X Cable length: 52-1/2”.
Deck Engagement Cable
Fits AYP, Poulan and Husqvarna riders.
285-004
Part#
145755
184588
Control Cable
For AYP /
Husqvarna equipment.
Overall Length with Spring: 60-3/4″
285-006
continued
Drive Control Cable
For AYP built
self-propelled
walk behind push mowers. Fits models: 96142003700,
96142006900, 96142008400, 96142008401, 96143006105
96143008001, 96143005800 and 961430061.
Die cast Z-bend on one end with a spring on the other.
Conduit length: 59-1/2” X Cable length: 68-1/2”.
20-05
C
Banta CONTROLS - THROTTLE & ACCESSORIES
AYP
BOBCAT
continued
Part#
O.E.M
285-695
189182
Application
Husqvarna#
532 18 91-82
Drive Control Cable
For AYP built self-propelled
walk behind push mowers.
Fits models:
96143000100 & 954223883.
Die cast Z-bend on one end with a spring on the other.
Conduit length: 59” X Cable length: 68-3/4”.
285-005
146323
O.E.M
290-410
118020-07
Application
Throttle Control
Fits medium size walk
behind versa deck with
14 HP Kawasaki engine.
(New Style - Long Handle)
Conduit length: 29″,
Inner Wire Length: 31-1/2″, Wire travel: 1-5/8″
BRIGGS & STRATTON
295-089
Control Cable
For 22″ self propelled
walk behind mowers.
Flexible inner wire with
spring on end,
Z-bend on spring.
Conduit length: 56″
290-035
Part#
290568
691028
Control Head
Fits models 28B702, 28B707,
28D707 and 28M707.
Head assembly only.
Includes: wire swivel and threaded
conduit button for 3/16″ conduit.
170803
(For Briggs and Stratton ″conduit clips″ - see page 20-01)
Throttle Control
For lawn tractors with
twin cylinder engines.
Conduit Length: 32″,
Inner Wire Length: 34″
290-241
285-589
Drive Control Cable
For Murray / Briggs and
Stratton snowblowers.
FR-DR P7 5-13B.
Measures: 31-1/4″ Overall Length,
Cast Z-Bends on both ends.
131922
Husqvarna #
532 13 19-22
Throttle Control
Fits AYP and
Husqvarna equipment.
Conduit Length: 57-1/4″,
Inner Wire Length: 59″
290-635
287-001
Chute control cable
For Murray / Briggs and Stratton snowblowers.
Measures: 69-1/2″ Overall Length, Conduit Length: 62″,
Wire Travel: 5-1/4″, Eyelet hole ID: 5/16″.
287-002
761775
761775MA
851250
Husqvarna# 532 85 16-69
Engine Control Cable
Fits AYP & Husqvarna equipment. ″Z″ bend on each end.
Conduit Length: 53-3/8″, Cable Length: 60-3/8″.
C
761131
761131MA
87025
133049
Drive Cable
Fits AYP equipment.
Threaded end for adjustment
with Z-bend on end.
Conduit Length: 59-3/4″,
Inner Wire Length: 63-1/2″
290-237
1502113MA
Chute control cable
For Murray / Briggs and Stratton snowblowers.
Measures: 63-3/4″ Overall Length, Conduit Length:
57-1/2″, Wire Travel: 3-1/4″, Eyelet hole ID: 5/16″
with a Cast Z-Bend on the other.
20-06
C
CONTROLS - THROTTLE & ACCESSORIES Banta
EXMARK
Part#
O.E.M
290-795
633696
1-633696
HONDA
Application
continued
Part#
O.E.M
260-306
17910-VA3-003
17910-VA3-S01
Application
Code# 1660281
Throttle Control
Fits Lazer Z models; also fits
Metro HP, Turf Tracer, Viking,
Lazer & Turf Ranger.
Conduit length: 54″,
Cable Length: 56-1/4″
Throttle Cable
Fits models HR194, HR214, HR215 and HR216.
For 4 and 5 Hp engines. Conduit length: 53-1/2″,
Overall Length: 57-1/4″. Thread Length: 1-3/32″.
290-799
260-322
603336
1-603336
54530-VA3-J01
54530-VA3-J03
Code# 3451002 / 4909818
Choke Control
Fits models 52″ & 60″ Turf Tracer
hydro drive unit floating decks. (Positive Action).
Conduit length: 54″, Cable Length: 58-3/4″
285-488
Blade Stop Cable
Fits models HR215SXA, HXA, K1SXA, K1HXA, HRC215,
K1SDKA, HRC216HXA, SXA, K1HXA and K1SXA.
Conduit length: 54″, Inner wire length: 65″,
Wire Travel: 9″.
Blade Brake Cable
Fits Exmark self propelled mowers. Found on Exmark
Metro Commercial 21, 21” Heavy Duty Recycler / Rear
Bagger lawnmower, 2007 (Exmark SN 370,000 thru
439999). Conduit Length: 60-5/8”, Inner Wire Length:
66”, Wire Travel: 4-3/8”. Overall Length: 68”. Metal
Z-Bend on one end with a rectangular female on the other.
260-323
54530-VE0-003
Code# 4010583
(See TORO / WHEEL HORSE heading)
Blade Stop Cable
Fits models HRB21SXA, HRB215K1SXA & HRB215K2HXA.
Conduit length: 45″, Inner wire length: 54-3/4″,
Wire Travel: 9-1/4″
HONDA
260-302
54510-VB5-800
Code# 2963627
260-324
54530-VB3-802
54530-VA4-010
Code# 2813327 / 2660645
Transmission Cable
For 21″ walk behinds. Fits models HR21, HRA216 from
1988 thru 1991, HRC 216 from 1992 and newer
with 2 speed transmission and HRC216K1SXA.
Conduit Length: 44-1/2″, Overall Length: 49-1/2″
260-303
54520-VA3-801
260-314
Code# 1618057
Transmission Cable
Fits model HR214 walk behinds. Conduit length: 42-1/8″,
Inner wire: 44-3/4″ Wire Travel: 2-5/8″
260-327
54520-VA3-P03
54520-VA3-PO102
Code# 4059085
Blade Stop Cable
Fits models HR214SXA and HRA214SXA.
Conduit length: 53″, Inner wire length: 68-1/2″
Wire Travel: 10″
54520-VB5-P00
Code# 3430261
Transmission Cable
Fits models HRC216K1HXA and HRC216HXA.
Conduit length: 42-3/4″, Inner wire: 47-5/8″,
Wire Travel: 3-1/2″
260-299
54510-VE2-305
54510-VE2-801
Code# 5317656
Code# 4010567
Transmission Cable
Fits models HR215HXA & HR215K1HXA.
Conduit length: 42-3/4″,
Inner wire: 47-1/2″. Wire Travel: 3-3/4″
C
Clutch Cable
Fits models HRB215SXA
and HRB215K1SXA.
Conduit length: 42-1/8″, Inner wire length: 48-1/2″
20-07
C
Banta CONTROLS - THROTTLE & ACCESSORIES
HONDA
HUSQVARNA
continued
Part#
O.E.M
295-304
16516-891-000
16576-891-000
Application
continued
Part#
O.E.M
285-560
532 42 83-11
Application
(Sold in multiples of 10)
Conduit Clip for HONDA
Fits engine models:GX110, GX120, GX140,
GX160, GX240, GX270, GX340 & GX390
Chute Control Cable
For AYP / Craftsman / Husqvarna / Sears snowblowers.
Models 2009 on. (Includes a heat resistant conduit cover = 14″
long approximately). Measures: 45-3/4″ Overall Length,
Conduit Length: 31-3/4″, Wire Travel: 11-3/4″.
HUSQVARNA
285-000
532 43 51-11
532 40 87-14
532 19 72-57
285-562
532 42 82-74
Deck Engagement / PTO Cable
Fits on many riders built by AYP. Found on 38″
and 42″ riders. Fits CT126, LTH1438, LTH1538,
LTH18538, YT16542 and YT1942. Length: 69″
Chute Control Cable
For AYP / Craftsman / Husqvarna / Sears snowblowers.
Models 2009 on. Measures: 46-1/2″ Overall Length,
Conduit Length: 32-7/8″, Wire Travel Adjustable: 11″
thru 11-3/4″.
285-001
285-564
532 16 96-76
532 17 50-67
Deck Engagement /
PTO Cable
Fits on many riders built by AYP.
Found on 42″ riders; also
replaces AYP# 192413 found on
Sears model YT3000 (model 942-605911), 22 Hp with
42″ cut. Fits LT16542, LT18542, LT18542A, LT18542B,
LTH1342, LTH1342A, LTH1342B, LTH1342C, LTH1742A,
LTH1742B, LTH1742C, LTH1742D, LTH18542A,
LTH18542B, LTH18542C, LTH2042A, LTH2042B,
LTH2042C, YTH130, YTH1842A, YTH1842B, YTH1842C.
Conduit Length: 32″, Cable Length: 45″
285-008
532 16 96-76
532 17 50-67
285-009
JOHN DEERE
AM134542
Throttle & Choke Assembly
Fits on X300 series tractor.
Conduit Length: 33”,
Inner Wire Length: 35.5”,
Wire Travel: 1”,
Inner Wire Diameter: .062” (both choke and throttle)
LAWN BOY
290-205
682685
532 14 57-55
532 18 45-88
Control Cable
For AYP /
Husqvarna equipment.
Overall Length with Spring: 60-3/4″
C
Chute Control Cable
For AYP / Craftsman / Husqvarna / Sears snowblowers.
Cable only. Measures: 59-1/4″ Overall Length,
Conduit Length: 50-3/4″, Inner Wire Length: 57-1/2″,
Wire Travel: 3″, Eyelet hole ID: 5/16″ with a Cast Z-Bend
on the other.
290-051
Deck Engagement /
PTO Cable
Found on many riders.
Fits LT16542, LT18542, LT18542A, LT18542B,
LTH1342, LTH1342A, LTH1342B, LTH1342C, LTH1742A,
LTH1742B, LTH1742C, LTH1742D, LTH18542A,
LTH18542B, LTH18542C, LTH2042A, LTH2042B,
LTH2042C, YTH130, YTH1842A, YTH1842B, YTH1842C.
Conduit Length: 32”, Overall Length with Spring:
45-1/2”, Spring Length: 6”.
532 17 86-74
532 42 06-73
Control Cable
Fits 21″ self propelled steel decks, rear discharge models.
Conduit length: 55-1/4″, Inner wire length: 64-1/4″.
Eyelet ID: 5/16
20-08
C
CONTROLS - THROTTLE & ACCESSORIES Banta
MTD / CUB CADET
Part#
O.E.M
295-166
731-0972
731-0528
MTD / CUB CADET
Application
Throttle Control Lever
For all MTD walk behind mowers. Models 120-176,
120-178B, 120-466B, 120-468B, 120-476B and 120-478B.
295-170
811-0185
Throttle Control Head Assy
Includes: MTD# ‘s
746-0875 and 746-0876.
For use with our 295-545,
547, 552, 555, 558 and 561 throttle cables.
295-168
Part#
O.E.M
295-569
746-0776
Application
Throttle Cable
Fits 1995 thru 1998 MTD riders models 135 and 136
with Briggs engines only. Conduit length: 18-1/2″,
Inner wire length: 21-1/2″. Z-bends on both ends,
Wire Travel: 2-1/4″
295-557
831-0823A
cont.
746-0630
746-0630A
Throttle Cable
Fits walk behind mowers.
Conduit length: 37″,
Inner wire length: 42″. Z-bends on both ends
295-516
746-0841
Throttle Control Head Assembly
295-552
746-0845
Throttle Cable
Fits 1992 and later push & self propelled mowers with
Tecumseh engines.
Fits models: 081, 085, 087, 232-238, 280, 281, 282,
413, 415, 423, 425, 460, 478, 50, 508, 516 & 518.
Conduit length: 45″, Inner wire length: 47-3/8″
Z-bends on both ends. Wire travel: 2-5/8″
295-555
746-0843 / 746-0671A
Throttle Cable
Fits MTD models 370-389, 559, 959, 979, E979
and 999, 1997 thru 2002 push and self propelled units.
Conduit length 60″, Z-bend on end,
Inner wire length: 62-1/2″, Wire travel: 2-1/2″
295-518
Throttle Cable
Fits models 12A-998Q401, 11A-418Q118 and 12A378Q118
Yardman. Conduit length 42″, Z-bend on end,
Inner wire length: 44-1/2″, Wire travel: 2-1/2″
295-545
Throttle Cable
Fits 1992 and newer push & self propelled mowers with
Briggs and Stratton engines. Fits models:
083, 088, 123-238, 246, 328, 338, 414, 416, 418, 424,
426, 428, 446, 448, 456, 458, 460-479, 488, 518, 528.
Conduit length: 55-3/8″, Inner wire length: 57-3/4″
Z-bends on both ends. Wire travel: 2-1/2″
295-558
746-0842
C
746-0632 / 746-0474
Wards# 90144855
Throttle Cable
For walk behind and self propelled walk behind mowers
that require a 53″ green tip.Conduit length: 53-1/2″,
Inner wire length: 56-3/8″. Z-bends on both ends.
Spring length: 8-1/2″, Wire travel: 2-3/4″
295-547
Throttle Cable
Fits 1992 and newer push mowers with
Briggs and Stratton engines. Fits models 030-042,
050-063, 070-088, 092-098, 108-206, 260-265, 280, 281,
282, 440, 442, 450, 452, 460, 479, 500-508 and 570.
Conduit length: 51-1/4″, Inner wire length: 53-5/8″
Z-bends on both ends. Wire Travel: 2-1/2″
746-0847 / 746-1115
746-0672
Wards# 90185780
Throttle Cable
For walk behind and self propelled walk behind mowers
that require a 58″ yellow tip. Conduit length: 58″,
Inner wire length: 60″ Z-bends on both ends.
Spring length: 8-1/2″, Wire travel: 2-1/2″
20-09
C
Banta CONTROLS - THROTTLE & ACCESSORIES
MTD / CUB CADET
Part#
O.E.M
295-561
746-0674
cont.
Application
Wards# 90265520
Throttle Cable
For walk behind and self propelled walk behind mowers
that require a 61″ black tip. Conduit length: 61-3/8″,
Inner wire length: 64-3/8″. Z-bends on both ends.
Spring length: 8-1/2″
295-855
746-0634 / 746-0634A
Wards# 90148877
Throttle Cable
Fits MTD models 600-609, 660-669, 670-679, 690-699,
series tractors with twin cylinder engines. Also fits
series 820-829 and 840-849 tractors. Conduit length: 35″,
Inner wire length: 38″. Z-bends on both ends.
Wire travel: 3″.
290-049
MTD# - - - - - - Murray# 22058
Murray# 42775
Noma# 52087
Throttle Control
Fits MTD and many others.
This is a universal positive
action plastic control head, sliding lever type.
Conduit length: 44″, Inner wire length: 47″
290-106
746-0970
Brake Cable
For MTD 42″ decks.
3/8″ eyelet on each end.
Also used as a ″Deck Lift Cable″
on Cub Cadet Zero turn models
(2005 thru 2006) with 50″ cut decks.
Overall length: 5-3/4″
C
O.E.M
295-804
746-0968
Application
Deck Lift Cable
Fits MTD mowers.
Lanyard cable with swivel pins.
Length: 17″.
285-401
746-0553
Safety control cable
Fits 1991 and newer push
mowers with Briggs engines.
Models 030-042, 030-414,
030-416, 030-418, 030-424,
030-426, 030-428, 030-446, 030-448, 030-456,
030-458, 030-506, 030-508, 030-570 and 030-580.
Conduit Length: 36-7/8″ X Cable Length: 43-1/8″,
Heavy ″Z″ bends on both ends.
285-407
746-0550
Safety control cable
Used on push mower
models 040, 050, 060,
070, 080 and 090. Used on self - propelled models
100, 200, 400 and 700. 1985 to present.
Conduit Length: 40″ X Cable Length: 46-3/8″
Heavy ″Z″ bend on both ends.
285-402
746-1130
Safety control cable
Fits MTD models 22″ deck, series 038, 2003 thru 2007.
Conduit Length: 40″ X Cable Length: 53″,
Heavy ″Z″ bends on both ends, Snap-on handle fit.
285-603
746-0552
746-1086
Throttle Control
Fits lawn tractors with
Briggs and Stratton Intek
engines built from
1999 through 2002.
Conduit Length: 42″ X
Inner wire length: 45″, ″Z″ bend on end.
285-423
Part#
cont.
MTD# - - - - - - -
Throttle Control
Fits MTD and many others.
All plastic controls come
with galvanized inner wire.
Used on MTD, AYP, Air Cap,
Murray & many others.
Wire travel: 1-3/8″.
Conduit length: 60″, Inner wire length: 67″
290-024
MTD / CUB CADET
Safety control cable
Used on push mowers. Push in clips with heavy
″Z″ bend on each end. Replaces blue cable.
Conduit Length: 49-7/8″ X Cable Length: 55-1/2″.
Wire travel: 5″
285-408
746-0555
946-0555
Safety control cable / Engine brake cable.
For MTD model 573, 20″ deck, model 370-379, model 445,
21″ rear discharge. Conduit: 55″, Inner Wire: 61-1/2″
Push in clips with heavy ″Z″ bend on each end.
20-10
C
CONTROLS - THROTTLE & ACCESSORIES Banta
MTD / CUB CADET
Part#
285-611
O.E.M
cont.
Application
746-0551
Safety control cable
Used on MTD mowers.
Fits model 440, E466 & 469 series.
Conduit Length: 43″ X Inner Wire Length: 49-1/2″,
Wire travel: 4-3/4″. Push in clips with heavy
″Z″ bends on each end.
285-409
MTD / CUB CADET
Part#
O.E.M
285-404
746-0405A
746-0946 / 946-0946
Engine Stop Cable
Fits most MTD side discharge mowers 1986 and prior.
Snap fit to handle. Conduit Length: 48-1/4″ X
Cable Length: 60-1/4″, Heavy ″Z″ bend on both ends.
746-0554
Safety control cable
Used on MTD mowers. Fits 1990 thru 1996 walk behind
model series 300, 400 and 500. For 1998 & up model
series 070 & 100. For 1990 & up self propelled model
series 300, 400 & 500. Conduit Length: 40-1/2″ X
Inner Wire Length: 47″, Wire travel: 4-5/8″.
Push in clips with heavy ″Z″ bends on each end.
285-617
746-0737
Safety control cable
Used on MTD mowers. For 1994 thru 1997 walk
behind model series 070, 080, 100, 200, 400 & 500.
Conduit Length: 51″ X Inner Wire Length: 55-1/2″,
Wire travel: 4-5/8″. Push in clips with heavy ″Z″ bends on
each end.
285-400
Deck Engagement Cable
Fits 13**7** model riders built after 2004.
Overall Length including Spring: 55-1/2”.
Conduit Length (from mounting face to mounting face:
38-1/8”), Spring Length: 6”
285-440
746-04618
946-04618
946-04618A
Deck Engagement Cable
For Cub Cadet / MTD / Troy Bilt mowers.
Fits Cub Cadet LTX1040 series 13AT, 13AX, 113WX,
with 42” and 46” decks. Conduit Length: 40-1/2”,
Inner Wire Length: 52-3/4”, Wire Travel: 8”
approximately. Overall Length with Spring: 59-3/4”.
Spring Length: 6”. Metal Z-Bend on one end.
285-410
746-04206 / 746-04206A
946-04206 / 946-04206A
Control Cable
Variable speed drive cable for MTD.
Overall Length: 79-5/8″, Black outer condiut length: 76″.
285-600
746-1113 / 946-1113
Safety control cable
For MTD / Cub Cadet / Troy Bilt equipment.
Conduit Length: 37-3/8″ X Cable Length: 51″,
Wire Travel: 12″; Heavy ″Z″ bends on both ends.
C
746-04173 / 746-04173A
746-04173B / 946-04173
946-04173A / 946-04173B
746-1132
946-1132
Safety control cable
Used on MTD mowers. Fits walk-behind mowers.
Conduit Length: 40-3/4” X Inner Wire Length: 54”,
Wire travel: 12”. Push in clips with heavy “Z” bends on
each end.
285-613
Application
Control Cable
Fits 5.5 Hp rear bagger self-propelled models.
Conduit Length: 46″ X Cable Length: 53-3/4″.
Heavy ″Z″ bend on one end with a spring around the
outer conduit and 90 degree hook on the other end.
285-406
285-612
cont.
946-0898
746-0898A
746-0898
Clutch Drive Cable
Fits 600 model series snow
blowers built 1995 thru 2002
and 700 model series built in 2003.
Overall Length: 43″
20-11
C
Banta CONTROLS - THROTTLE & ACCESSORIES
MTD / CUB CADET
Part#
O.E.M
285-599
746-0897 / 746-0897A
746-0778 / 946-0897
946-0778 / 946-0897A
cont.
Application
MTD / CUB CADET
Part#
O.E.M
285-602
746-0600
Auger Clutch Cable
Fits 400 thru 600 series
MTD snow blowers built
1992 thru 2004.
Overall Length with spring: 44-3/4”.
Clutch Cable
Used on push mowers.
Overall Length: 59″
Conduit Length: 47-1/2 X
Cable Length: 54-1/2″
Wire travel: 6-1/2″,
Spring Length: 4-1/2″
(Note: Threaded rod NOT included,
sold separately - see our part# 285-590).
285-403
285-590
285-405
746-0951
946-0951
746-04227A
746-04396
746-04396A
946-04396
946-04396A
285-588
746-04228A
Speed Selector Control Cable
For MTD snowblowers.
Found on MTD / White models:
31AE6BHE718, 31AE6GLF00,
09, 19, 26, 31AE6GLF795, 31AE6L04766, 31AH6BHE790,
31AS6BEE700, 31AS6BEE731, 31AS6FEF700.
Measures: 24-1/8″ Overall Length, Cast Z-Bend on one
end and a cast barrel end on the other.
C
NOTE: Similar to picture
except with a z-bend on the end where the picture shows a barrel end.
746-04229
Wheel Drive / Clutch Cable
For MTD built snowblowers.
Overall Length including
spring: 45-3/8″,
Overall Spring Length: 2-1/8″.
285-596
Speed Selector Control Cable
For MTD snowblowers. Found on MTD .
Measures: 22-1/8″ Overall Length, Cast Z-Bend on one
end and a cast hammer head end on the other.
746-0910A
Clutch Cable
For snowblowers.
Conduit Length: 35-5/8,
Total Length: 42-1/4″
285-594
Speed Selector Control Cable
For MTD snowblowers. Found on
MTD Pro series model 31AE6BHE718 (2005 and newer).
Measures: 22-1/8″ Overall Length, Cast Z-Bends on one
end and a cast barrel end on the other.
285-584
746-0629
Clutch Cable
Used all self propelled
walk behind mowers
with cog front wheels.
Conduit Length: 37″,
Total Length: 48″
Auger Idler Control Cable
For MTD snowblowers. Found on 800 & 900 series
(large frame) snowblowers; 1998 & newer. Measures:
16-1/4″ Overall Length, Cast Z-Bends on both ends.
285-587
Application
746-0778
Threaded Control Cable End
Used on many MTD,
Murray and Noma /
Canadiana snowblowers.
Measures: 4-3/8″ Overall Length.
(Used on our 285-600 and 285-599 control cables)
285-586
cont.
746-04230
Wheel Drive / Clutch Cable
For MTD built snowblowers.
Fits models: 31AH5ZLH704,
31AM63LF704,
31AH6ZLG704 (2008), 31AE5KLF795, 31AE6GFF795,
31AE5MLH795 (2007), 31AE5KLF796 (2006),
31AE6BHE718 (2005 on). Overall Length including
spring: 48″, Overall Spring Length: 2-1/8″.
285-413
746-0713
Control Cable
For 21″ walk behind mowers.
Conduit Length: 53″,
Total Length: 57″
20-12
C
CONTROLS - THROTTLE & ACCESSORIES Banta
MTD / CUB CADET
Part#
O.E.M
290-840
746-0801
cont.
Application
Throttle Control
Fits MTD models
019, 070, 072, 080,
082, 200, 220,
222, 280 & 282.
Conduit length (including spring): 51-3/4″
Inner wire length: 52″, Z-bend on end,
Wire travel: 1-11/32″
290-038
746-1084
Throttle Control
Fits 600 series lawn tractors
with Briggs and Stratton OHV engines.
Conduit Length: 25″, Overall Length: 27″
290-042
746-1100
Throttle Control
Fits 800 series lawn tractors
with Kohler twin cylinder OHV engines.
Conduit Length: 38″, Overall Length: 40-1/2″
290-025
746-547
746-0390
746-0390A
Throttle control
For MTD built snowblowers.
Found on MTD, Yardman,
Columbia models 250, 280,
281, 450, 510, 511, 520, 580,
761, 766, 821, 840, 961.
Inner Wire Length: 32-1/2″,
Conduit Length: 30″, Wire Travel: 1-1/2″.
290-048
746-04066
Throttle control
For Cub Cadet models: RZT 50,
RZT 54, GT1222 mowers.
Conduit Length: 34-3/8”, Inner Wire Length: 37”,
Wire Travel: 1-5/8”, Inner wire diameter: .062”.
290-683
746-0616
746-0616A
Choke Control
Fits on lawn tractors.
Conduit Length: 18-3/4″,
Overall Length: 26″
Inner wire length: 24-1/4″,
Wire travel: 1-1/2″
290-041
Part#
O.E.M
290-519
746-3021
cont.
Application
Choke Control
Fits models 662-672 & 678.
Conduit Length: 29″,
Inner wire length: 32″,
Wire travel: 1-1/2″, ″Z″ bend on end
290-682
746-0614
746-0614A
Choke Control
Fits on mid-sized rear engine
riders. Conduit Length: 34″,
Overall Length: 41″
Inner wire length: 39-1/4″,
Wire travel: 1-1/2″
290-039
746-1085A
Choke Control
Fits on lawn tractors.
Conduit Length: 37″,
Overall Length: 39″
290-681
746-0613
746-0613A
Choke Control
Fits on lawn tractors.
Conduit Length: 42″,
Overall Length: 49-1/2″
Inner wire length: 48″,
Wire travel: 2-1/4″
290-044
746-04120
Choke control
For Cub Cadet / MTD applications. Fits Cub Cadet models:
i1046, i1050, GT1222, GT1554, SLT1550, SLT1554,
LT1018, LT1022, LT1024, LT1042, LT1045, LT1046,
LT1050 mowers. Overall Conduit Length: 40-1/2” X
Inner Wire Length: 42-1/2”, Wire Travel: 2”, Inner wire
Diameter: .062”.
285-608
746-0694
Lock-out Cable /
Clutch Cable
Fits MTD 800 to 996 series.
1989 & later; also used on
small frame Noma snowblowers
as a clutch cable; models: 523, 825.
Overall Length: 28-3/4″, Cable Length: 23-3/4″
285-591
746-0716
746-1088
Choke Control
Fits on lawn tractors.
Conduit Length: 23″,
Overall Length: 24″
(For more MTD controls see Banta
catalogue pages 20-07 thru 20-09).
C
MTD / CUB CADET
Lock-out Cable /
Auger Clutch Cable
For MTD built snowblowers.
Overall Length: 23-1/4″.
Cast Z-Bend on one end with a
1/4″ diameter threaded end on the other.
20-13
C
Banta CONTROLS - THROTTLE & ACCESSORIES
MTD / CUB CADET
Part#
O.E.M
285-592
746-0952
946-0952
cont.
Application
MURRAY / NOMA
Part#
O.E.M
290-122
21222PA
Lock-out Cable /
Auger Clutch Cable
for MTD built snowblowers.
Fits MTD 800 and 900 series, large frame snowblower.
(1998 and newer). Overall Length: 26-1/2″. Cast Z-Bend
on one end with a 1/4″ diameter threaded end on the other.
Throttle Control
Positive action control.
Plastic covered conduit - black.
Conduit length: 60″,
Inner wire length: 64-1/2″
Conduit size: 3/16″,
Inner wire size: .058″
Wire travel: 1-3/8″
285-593
290-175
746-04086
946-04086
Lock-out Cable /
Auger Clutch Cable
For MTD built snowblowers.
Fits MTD 500 and 600 series snowblower.
Overall Length: 42-3/4″, Coil Spring Length: 2-1/2″.
285-598
746-0896
946-0896
Chute Control Cable
For MTD Snowblowers.
Fits newer models built
since 1993.
Conduit Length: 47″,
Overall Length: 54-1/4″;
Wire Travel: 6-3/4″
MURRAY / NOMA
290-049
22058
52087
Throttle Control
Fits Murray,
Noma and others.
Conduit length: 44″,
Inner wire length: 47″
This is a universal positive action
plastic control head, sliding lever type.
290-106
42096 / 42776
42877 / 42878
42879 / 42949
53415 / 57353
Throttle Control
Fits Murray and many others.
Conduit length: 60″,
Inner wire length: 67″
All plastic control with
galvanized inner wire. Wire travel: 1-3/8″
Used on MTD, AYP, Air Cap, Noma and others.
290-114
21540PA
23332PA
Throttle Control
Positive action control.
Conduit length: 14″,
Inner wire length: 17-5/8″.
Conduit size: 3/16″,
Inner wire size: .058″, Wire travel: 1-3/8″
C
cont.
Application
71180
71157
420005
Throttle Control
Fits most Murray walk
behinds. Converts easily
from positive tonegative action.
Conduit length: 50″,
Inner wire length: 55″
Plastic Conduit size: 3/16″, Wire travel: 1-1/2″
290-961
Murray
Throttle Control
Heavy duty throttle control fits
Murray walk behind mowers.
Plastic conduit converts from
positive to negative action.
Conduit length: 70″,
Inner wire length: 76″
Plastic Conduit size: 3/16″, Wire travel: 1-1/2″
(Note: light duty version us our 290-002 found on page 20-03.)
290-262
52061
52769
Throttle Control
For walk behind steel deck
mowers with Briggs and
Stratton engines.
Conduit length: 48-3/4″,
Inner wire length: 52-3/16″,
Wire travel: 1-1/8″ Conduit size: 3/16″
290-112
50877 / 51223 / 53943
780232 / 780232MA
Throttle Control
Found on Ariens, Murray / Noma snowblowers.
Conduit length: 30-1/4″, Inner wire length: 33″,
Conduit size: 3/16″, Inner wire size: .055″,
Wire travel: 1-3/4″.
295-506
Murray
Mounting Adapter
For use with our Murray
throttle controls # 290-175,
290-961 and 290-002.
20-14
(Sold in multiples of 10)
C
CONTROLS - THROTTLE & ACCESSORIES Banta
MURRAY / NOMA
Part#
O.E.M
290-684
91989
Application
Throttle Control
For panel mounting.
Overall length: 26-1/2″
Conduit length: 21″,
Inner wire length: 23-1/2
Wire travel: 7/8″
290-685
MURRAY / NOMA
cont.
740194 / 7701016
Part#
O.E.M
285-597
4052 / 4052MA
287-001
1579
1579MA
Lockout Cable /
Clutch Cable
Fits on small frame
Noma snowblowers models: 523 and 825.
Overall Length: 28-3/4″, Cable Length: 23-3/4″
285-595
761131
761131MA
Chute control cable
For Murray / Briggs and Stratton snowblowers.
Measures: 69-1/2″ Overall Length, Conduit Length: 62″,
Wire Travel: 5-1/4″, Eyelet hole ID: 5/16″
287-002
761775
761775MA
1580
Clutch Drive Cable
For Murray / Noma
snowblower. Fits Small
Frame snowblower models: 523, 825 etc.
Overall Length: 32-5/8″, Cable Length: 27-5/8″.
285-710
Application
Chute Control Cable
For Murray / Noma snowblowers.
Measures: 59-3/8″ Overall Length, Conduit Length with
both threaded end: 52″, Wire Travel: 5-1/2″
Throttle Control
Fits high wheel trimmer.
Overall Length: 49″,
Conduit Length: 44″
285-608
cont.
1501124
1501124MA
762259MA
1501124MA
762259MA
Chute control cable
For Murray / Briggs and Stratton snowblowers.
Measures: 63-3/4″ Overall Length, Conduit Length:
57-1/2″, Wire Travel: 3-1/4″, Eyelet hole ID: 5/16″ with
a Cast Z-Bend on the other.
285-712
339496
339496MA
Auger Clutch Cable
Found on Murray / Noma snowblowers.
Overall Length: 32-3/4″, Cable Length: 31″.
285-709
1501123
1501123MA
Clutch Cable
Found on Murray / Noma
snowblowers.
Overall Length: 30-1/2″,
Cable Length: 29-1/2″
285-708
1501122
1501122MA
Control Cable
Lower Drive Cable
Found on Murray / Noma
snowblowers.
Overall Length: 12-3/4″,
Cable Length: 12″
C
Chute Control Cable
For Murray / Noma snowblowers.
Measures: 50″ Overall Length,
Conduit Length: 43″, Wire Travel: 6″
290-615
776113
Choke Control
Black plastic conduit with
reinforced wire wrapped end.
Overall Length: 51-3/4″
290-043
175441 X 428
Choke Control
Fits on many lawn & garden tractors.
Conduit length: 42″, Overall Length: 44″
20-15
C
Banta CONTROLS - THROTTLE & ACCESSORIES
MURRAY / NOMA
Part#
O.E.M
285-707
579856
579856MA
MC579856
Application
Traction Cable
Found on Murray / Noma snowblowers.
Overall Length: 6-5/8″, Cable Length: 5-1/8″.
285-629
1101344
Drive Cable
For self - propelled 22″
walk behind mowers.
Conduit Length: 59″,
Cable Length: 61″
285-711
1501452
501452MA
Drive Cable
Found on Murray / Noma snowblowers.
Overall Length: 35-3/4″, Cable Length: 34″.
285-589
1502113MA
Drive Control Cable
For Murray / Briggs and
Stratton snowblowers. FR-DR P7 5-13B.
Measures: 31-1/4″ Overall Length,
Cast Z-Bends on both ends.
285-606
42569
Engine Stop Cable
Plastic covered
conduit with brackets.
Conduit Length: 44-1/2″ X
Cable Length: 52-1/2″,
Wire travel: 7-1/2″,
Heavy ″Z″ bend on each end.
285-605
43749
42363
Engine Stop Cable
Fits push mower models
22651X-8A, 5A, 12A,
15A and 22651A.
Conduit Length: 45-1/2″,
Cable Length: 54-1/2″,
Wire travel: 7-3/8″,
Heavy ″Z″ bend on each end.
285-631
1101366
Engine Stop Cable
Fits 22″ walk-behind mowers
made from 2001 thru 2003
with rear bagger.
Conduit length: 52″,
Inner wire length: 59-1/4″
with a 3/16″ ″Z″ bend on each end.
C
MURRAY / NOMA
cont.
Part#
O.E.M
285-615
43361
cont.
Application
Engine Stop Cable
Fit Murray model TVS90 on left hand side of
20″ and 22″ walk behinds with Tecumseh engines.
Conduit Length: 36-7/8″, Inner wire length: 46″
with 3/16″ ″Z″ bend on each end.
285-697
43828
Engine Stop Cable
Fits 22″ walk-behind mowers
Conduit length: 40″, Inner wire length: 48-1/2″
with 3/16″ ″Z″ bend on one end, 1/4″ ″T″ on other end.
285-630
1101360
Engine Stop Cable
Fits 20″ walk-behind push
mowers with rear bagger
made from 2001 thru 2003.
Conduit length: 42-1/2″, Inner wire length: 48-3/4″
with 3/16″ ″Z″ bend on one end, 1/4″ ″T″ on other end.
285-633
672840
Engine Stop Cable
Fits walk-behind mowers
made from 2000 thru 2003.
Conduit length: 42-1/2″, Inner wire length: 50″
with 3/16″ ″Z″ bend on one end, 1/4″ ″T″ on other end.
285-625
1101093
Engine Stop Cable
Fits 20″ walk-behind mowers
made from 2000 thru 2003.
Conduit length: 44″, Inner wire length: 50″
with 3/16″ ″Z″ bend on one end, 1/4″ ″T″ on other end.
285-626
1101181
Engine Stop Cable
Fits 20″ and 22″ walk-behind
mowers made from 2001 thru 2002.
Conduit length: 45-1/4″, Inner wire length: 52-1/4″
with 3/16″ ″Z″ bend on one end, 1/4″ ″T″ on other end.
285-700
43881
Safety Control Cable
Conduit length: 46”,
Inner wire length: 54-3/4” with 3/16”
Z-bend on one end, 1/4” (T) on other end.
20-16
C
CONTROLS - THROTTLE & ACCESSORIES Banta
MURRAY / NOMA
Part#
O.E.M
285-614
43830
MURRAY / NOMA
cont.
Application
Engine Stop Cable
Fits Murray.
Conduit Length: 49″ X Inner Wire Length: 57-1/2″
with 3/16″ ″Z″ bend on one end, 1/4″ ″T″ on the other.
285-607
Part#
O.E.M
285-437
24072
23216
43827
285-148
Noma#
39299
Lift Cable
Measures: 20″ Long X
1/4″-20 threaded
end on the other.
285-632
285-412
672835
Engine Stop Cable
Fits walk-behind mowers
with Tecumseh engines
made from 2000 thru 2003.
Conduit length: 52-1/4″, Inner wire length: 59-1/4″
with 3/16″ ″Z″ bend on one end, 1/4″ ″T″ on other end.
Noma#
46512
Lift Cable
Fits 36″ and 42″ decks.
Measures: 17-1/2″ Long X
1/4″-20 threaded
end on the other.
285-494
1102094MA
Noma#
55938
53713
Lift Cable
Measures: 23″ Long
X 1/4″-20 threaded end.
Thread Length: 2-3/8″
Engine Stop Cable
For Murray. Conduit length: 43″, Inner wire length:
49-3/8″ with 3/16″ Z-bend on both ends. Wire Travel: 6″
285-634
740193
Control Latching Cable
For walk behind string trimmers.
Conduit length: 55-1/4″,
Inner wire length: 59″
″Z″ bend on end
285-726
21913
Lift Cable
Fits 36″ cut, 2 blade models.
Length: 21-1/8″,
ball one end with a 5/16″-18 threaded
rod on the other. Thread Length: 1-3/8″
285-817
24470
Lift Cable
Fits 38″ and 39″ cut models.
Length: 28-1/2″ with a barrel
one end and a 5/16″-18
threaded end on the other.
Thread Length: 1-3/8″
C
Application
Lift Cable
Fits 42″ cut models.
Length: 29-1/4″ with a barrel
one end and a 5/16″-18
threaded end on the other. Thread Length: 1-3/8″.
Engine Stop Cable
Fits walk-behind mowers.
Conduit length: 49-1/2″, Inner wire length: 57-7/8″
with 3/16″ ″Z″ bend on one end, 1/4″ ″T″ on other end.
285-616
cont.
(While Quantities Last)
SCAG
290-125
48780
Choke Control
Push-pull design
Conduit length: 55″,
Inner wire length: 58″,
Wire travel: 2″,
285-416
48828
Steering Cable
Fits 61″ and 72″ cut riders.
Models ST17KA and 19KH.
5/16″ barrel on each end
Length: 67-5/8″, Thread end: 3/8-24″
Cable diameter: 130″
SNAPPER
290-254
1-8237
Throttle Control
Used on Riders with
Tecumseh engines.
Positive action with
locking detents, side mount.
Conduit length: 13-1/2″, Inner wire length: 16-1/2″
20-17
C
Banta CONTROLS - THROTTLE & ACCESSORIES
SNAPPER
SNAPPER
continued
Part#
O.E.M
290-262
2-3449
1-8186
1-8515
Application
Throttle Control
For V series cast models with
Briggs and Stratton engines.
Wraps around back of engine.
Positive action, side mount.
Conduit length: 48-3/4″, Inner wire length: 52-3/16″,
Conduit size: 3/16″, Wire travel: 1-1/8″
290-411
1-1991
Throttle Control
Used on Riders with 8 Hp
Briggs and Stratton engines.
Front mounting.
For series 1 thru 3 and
26″, 30″ rear engine Riders.
Conduit length: 50″, Inner wire length: 52-1/4″.
290-068
1-8889
1-8353
1-8486
Throttle Control
Used on Riders with
Briggs and Stratton engines.
Negative action control, side mounted.
Conduit length: 12″, Inner wire length: 14-1/2″
285-026
1-5476
Brake Cable
Fits rear engine riders with
28″ & 30″ decks and one
brake/clutch pedal riders.
1/2″ eyelet on one end,
1/4″ barrel on the other end.
3 adjustment spacers, for series 6.
Length: 46-3/4″
285-027
1-5477
Brake Cable
Fits rear engine riders with
33″ & 41″ decks and one
brake / clutch pedal riders.
1/2″ eyelet on one end,
1/4″ barrel on the other end.
3 adjustment spacers, for series 6.
Length: 50″
290-240
1-9254
Throttle Control
For 21″ aluminum and Steel
deck series 7, 20″ series 0 with
Briggs and Robin engines.
Fits 1990 & 1991 V-21
Snapper with 5 Hp Quantum engines.
Heavy gauge steel construction / detents /
choke position / polyethylene covered.
Conduit length: 45″, Inner wire length: 47
C
continued
Part#
O.E.M
290-188
1-8188
Application
Throttle Control
For 21″ commercial walk
behind mowers, 1987 and
earlier. Equipped with
Briggs and Stratton 5 Hp engines.
Heavy duty 7/32″ outer conduit with
.072″ galvanized innerwire. Position action control.
Conduit length: 49″, Inner wire length: 51-1/8,
Wire travel: 1-1/2″
STIGA
285-219
(Dynamark / Noma)
329-496-185-00
Drive Control Cable
Fits Stiga NV walk-behind mowers.
Conduit: 48-1/4″, Length Extension: 8-27/32″
285-220
329-496-187-00
Drive Control Cable
Fits Stiga NV walk-behind mowers.
Conduit: 52-1/4″, Length Extension: 11″
STIHL - See TRIMMER PARTS - OEM
section - 50
TORO / WHEEL HORSE
295-070
70-1061
Throttle Cable
Fits old style 21″ Toro rear baggers.
Conduit: 49-25/32″, Inner Wire: 52-9/32″,
Wire Travel: 2-27/32″
290-056
12-9470
Throttle Control
Two hole mounting for side
or panel applications.
Conduit length: 48″,
Inner wire length: 51-1/2″
290-098
(While Quantities Last)
Toro / Wheel
Throttle Control
Provides direct linear
motion on panel or on 7/8″
diameter handlebar.
Conduit length: 46-1/2″,
Inner wire length: 48″
20-18
C
CONTROLS - THROTTLE & ACCESSORIES Banta
TORO / WHEEL HORSE
Part#
O.E.M
290-130
8105
102119
Application
Throttle Control
Locking push / pull cable
Marked ″T″ for throttle.
Conduit length: 41″,
Inner wire length: 43″,
Wire travel: 2″
290-148
8104
102118
105-1844
Traction Control Cable
Fits Toro 22″ Recycler
self-propelled mowers built
2002 thru 2008 with Personal Pace.
Length: 46-1/2″.
285-961
105-1845
Traction Control Cable
Fits Toro 22″ Recycler
self-propelled mowers built
2002 thru 2009 without Personal Pace.
Length: 67-1/2″.
285-962
106-8300
Traction Control Cable
Fits Toro 21″ Super Recycler
self-propelled mowers built
2003 thru 2005 with Personal Pace.
Length: ______
285-489
O.E.M
285-490
84-9120
Application
285-491
99-6291
Blade Brake Cable.
Fits Commercial 21″ Pro Line mowers.
Conduit Length: 62″, Inner Wire Length: 68-3/8″,
Wire Travel: 8-7/8″
285-488
103-2683
Blade Brake Cable
Fits Toro self propelled mowers. Found on Toro Consumer
22167, 21” Heavy Duty Recycler / Rear Bagger
lawnmower, 2007 (Exmark SN 370,000 thru 439999
(Honda powered and SN 440,000 thru 509,999 Kawasaki
powered) and 2006 (Toro SN 270000001 thru 270999999).
Conduit Length: 60-5/8”, Inner Wire Length: 66”,
Wire Travel: 4-3/8”. Overall Length: 68”. Metal Z-Bend
on one end with a rectangular female on the other.
285-492
70-1080
Drive Cable
Fits Toro self propelled commercial
PRO-LINE mowers. Model: 22621C (1989 and newer).
Conduit Length: 35-1/4″, Inner Wire Length: 45-1/4″,
Wire Travel: 10″.
285-493
74-1791
55-9322
Clutch Cable
Found on Toro snowblowers.
Overall Length: 30-3/4″,
Cable Length: 29-1/4″.
Cast Z-Bends on both ends.
C
Part#
Drive Cable / Traction Control Cable
For Toro Commercial PRO LINE Mowers.
Conduit Length: 31-1/4″ X Inner Wire Length: 37-1/2″,
Wire Travel: 6-1/4″; Heavy ″Rectangular″ eyelets on both
ends.
Throttle Control
This heavy duty
non rotational locking
control has a variety
of industrial uses. By turning T-knob 1/4 turn, control locks
securely against spring tension and vibration. Installation
hole: 9/16”. Max push load: 20 lbs, Max pull load: 50 lbs.
Conduit length: 92-1/2”, Inner wire length: 104”,
Inner wire diameter: .080”, Conduit size: 1/4”
285-960
TORO / WHEEL HORSE
Drive Cable / Traction Control Cable
For Toro Commercial PRO LINE Mowers.
Conduit Length: 34-5/8″ X Inner Wire Length: 43-1/2″,
Wire Travel: 8-7/8″; Heavy ″Rectangular″ eyelets on both
ends.
20-19
C

Similar documents

Illustrated Parts List

Illustrated Parts List Choke cable RZT 50 with Kawasaki engine 61" long Throttle cable LT1018

More information

Banta Snowblower Parts

Banta Snowblower Parts Fits models: 921001 / 002 / 003 / 004, 921300 and 921301, 926016 / 017 / 021 / 022 / 023 / 302 / 310 / 311 / 312 / 313 / 314 / 315 / 316 / 500 / 501 etc. Measures: 61-3/8” Overall Length, Wire Trav...

More information

spindles and parts

spindles and parts Image may not depict the actual size, shape, etc.

More information

Genuine Husqvarna Accessories

Genuine Husqvarna Accessories Scabbards • Impact resistant. Husqvarna logo.

More information

air filters

air filters KENDA SUPER TURF – K500 The best turf and garden tire on the market. It has more rubber on the contact surface, which equates to enhanced puncture resistance and longer tread life. Kenda K500 provi...

More information