TAGARNO AIR

Transcription

TAGARNO AIR
TAGARNO
AIR
You have received the following:
Manual
Camera Arm
Controller
Base
Rod, Washers, Screw
SD Card
2 DVI Cables
USB Cable
Power Supply
Power Cord
Hexagon Tool
1. Assembling TAGARNO AIR
Release button
Screw
1.1. Assemble base and rod with the screw
1.2. Pull the release button and place the camera arm on the rod
1.3. Fasten the two washers with the screw on top of the rod
1.4. The completed TAGARNO AIR
2
3. Connection
DVI cable (PC)
Controller
USB cable
DVI cable (monitor)
Power supply
3.1. Connect PC, USB cable, Controller, monitor and power supply
in that order.
3.2. Place the camera arm in the appropriate height
according to the lens you are using (see table p. 9)
3
4. Combinations
Live image
DVI cable
Live image
DVI cable
PC image
PC image
Or
4.1. TAGARNO AIR can be connected directly to a monitor
DVI and USB cable
4.2. TAGARNO AIR can be connected to a desktop or laptop and
an external monitor
PC image
PC image
DVI and USB
cable
Or
DVI in
USB cable
Power in
Splitter box
DVI cable
DVI out
DVI out
DVI cable
Live image
Live image
PC image
4.4. TAGARNO AIR can be connected to a desktop and
two monitors. One with the PC image and one with live image.
Live image
PC image
4.3.TAGARNO AIR can be connected to multiple monitors only adding
an active signal splitter between TAGARNO AIR and the monitors
4
5. Operation
On / Off
On / Off
5.1. Power on/off
5.2. Light on/off
SD slot
Regulator
On/Off
5.3. Backlight on/off and intensity regulator
5.4. Insert the supplied SD card into the SD slot
5
Operation
Snapshot Function
To take a picture and transfer it to the PC,
push this button on the control box down until you
hear a beep If the measurement software is not running, the
image will be transferred to the SD card
Memory Function (Preset Button)
ou can save three favourite settings by the help of the memory
Y
function
To save a favourite setting, press this button on the control
box until you hear a beep. First, you save under ‘Preset 1’,
second, you save under ‘Preset 2’ , third, you save under
‘Preset 3’
Note! The next time you save a preset, it will replace the
consecutive preset
5.3. Controller for TAGARNO AIR functions
Zoom
White Balance
Push this button on the control box to zoom in
Press the whitebalance button to perform an automatic whitebalance adjustment. There must be a white object
present in the camera’s field of view when the whitebalance is being
adjusted. When the whitebalance has been adjusted, the current
colour reference will be locked in the camera until the unit has been
turned off or a new whitebalance adjustment has been performed.
Push this button on the control box to zoom out
Manual Focus
Turn autofocus off by pushing both zoom buttons (plus and minus)
on the control box at the same time until you hear a beep. You can
now adjust focus manually with the help of the zoom buttons
NB! If the camera’s field of view does not contain a white object, when
the unit is turned on, the whitebalance will be incorrect and it will be
necessary to perform the whitebalance adjustment process described
above.
Push this button on the control box to adjust focus if you
wish to focus on something very close
Push this button on the control box to adjust focus if you
wish to focus on something that is farther away
Multi Function Buttons
To deactivate the automatic iris and gain levels, push the
button in the middle of the control box until you hear a beep
To turn the autofocus on again, simply pushing both zoom buttons
(plus and minus) at the same time until you hear a beep
To increase the iris, push the button that points towards this
icon
Split Screen Function
To return to your favourite settings at a later stage, push the button again. First, you enter ‘Preset 1’, second, ‘Preset 2’, third, ‘Preset 3’
To divide the monitor between what you see under the
camera and what you are working with on the PC, push
this button on the control box
Repeat the short push to change the position of the PC
image on the monitor (top, bottom, right, left)
To reduce the iris, push the button that points towards this icon
To increase the gain, push the button that points towards
this icon
To change the PC image size, use the multi function
buttons (arrows) to adjust up, down, back and forth
To reduce the gain, push the button that points towards this
icon
To view a full PC image on the monitor, push the button
until you hear a beep. Repeat this action to view a full
camera image
To activate the automatic iris and gain levels again, push the button in the middle of the control box until you hear two beeps
6
Operation
Functions in the Setup Menu
1.
To change the lens, from e.g. +10 to +32, enter 'Close-up lens' and
use the arrows to select the appropriate lens
2.
To find the optimal work distance for the chosen lens, enter 'Find
optimal working distance'
3.
To change between automatic or manual monitor detection, choose
'Monitor Detection' and use the multi function buttons to choose
'Auto' or 'Manual'
5.4. On-Screen Display
4.
For manually setting the monitor format, choose 'Monitor Panel
Width' and note the width in mm by using the multi function buttons
Note! This function only applies, when monitor detection is set to
manual
The on-screen display provides you with the relevant information
when you push a button on the control box - for instance if you
change the level of magnification, the white balance, iris, etc. In this
way you always know which function you are activating and which
parameters you are using
5.
To turn the on-screen display on or off, select 'On-screen display
mode' and select ‘on’ or ‘off’
Note! The level of magnification and the focus height depend on the
lens you are using. These figures are calculated on the basis of the
camera zoom level, the type of lens you are using and the size of
the monitor. TAGARNO AIR automatically detects the monitor size,
but you must always note which lens you are using in the set-up
menu to view the correct level of magnification (MAG.)
6.
To update the camera’s framerate, select 'Camera framerate' and
select '50 HZ' or '60 HZ'
Note! The update only takes place after restarting TAGARNO AIR
7.
To take pictures automatically, select 'Auto Snapshot on/off'.
8.
Then select 'Snapshot interval HH:MM:SS'
9.
To see which monitor is connected to TAGARNO AIR,
select 'Monitor Information' and ‘Panel format’ or 'Panel size'
To exit the set-up menu, push the memory function
button
5.5. Set-up Menu
5.6. The Shutter function
To enter the set-up menu, push the white balance and
memory function buttons on the control box at the
same time
You can increase or decrease the camera’s exposure time by using
the arrows.
To navigate in the set-up menu, use the multi function
buttons on the control box
The benefits of the shutter function can be emphasized by combining it with Iris adjustment. When using a small Iris, increase the
exposure time to achieve an optimal image.
7
6. Technical specifications
320 mm/12.6"
460 mm/18.1"
380 mm/14.9"
TAGARNO AIR
Dimensions:
Weight:
Power consumption:
Storage:
Operation:
Work height:
Work depth:
Monitor Format Detect:
Plug connections:
Zoom:
Camera resolution:
Autofocus:
Iris:
H: 460 mm/18.1", D: 360 mm/14.2", W: 320 mm/12.6"
9.5 kg
27W
-20 - +60 C, 5 - 90 % RH
0 - +45 C, 5 - 90 % RH
Min: 27mm/1.06", Max: 225mm/8.85"
150 mm/5.9"
Yes
DVI output (monitor), DVI input (PC), USB 2.0 and Sub-D (control box)
10x optical + 2x digital
HD720p, 1280x720 at 50/60 HZ
Yes
F1.8 to F26
8
Technical specifications
Ø58 mm/2.3"
Ø37/1.46"
58 mm
Lenses
AIR Control Box
Dimensions:
Functions:
H: 4.5 cm/1.8"
W: 12 cm/4.7"
D: 15 cm/5.9"
Zoom with auto focus and manual focus
Snapshot function
Iris and Gain adjustment
Split screen function
Memory function (programming key)
White balance adjustment
Dimensions:
Ø58mm/2.3", Ø37/1.46" (+25 and +32)
Lens
+10
+25
+32
+50
Lens to
object distance
100 mm/3.9"
40 mm/1.6"
31 mm/1.2"
33,5 mm/1.3"
Accessories
HD 22" and 24" widescreen monitor
Lenses +10, +25, +32 +50
MILLI and MICRO measurement software
Circular tilting table
Ring lights
Foot switch
Mounting arm for monitor
Table and wall holder for monitor arm
Keyboard holder
Aluminium case for transportation
Cleaning kit
On a 22" widescreen monitor the degree of magnification ranges
from 5.5 to 500 times depending on the lens that you are using
9
Magnification on
22" monitor
5.5x - 101x
13.6x - 249x
17.7x - 322x
225x - 450x
7. System requirements
Recommended monitor format
Panel format:
Input:
Response time:
Signal format:
16:9
DVI, HDMI or Display Port
2 ms (gtg)
HD720p
PC Hardware
At least one available USB 2.0 port
Graphic card with DVI-D, HDMI or Display Port
Resolution1280x720 60Hz
(required for split screen function)
Supported operative systems
Windows XP (32 and 64 bit)
Windows Vista (32 and 64 bit)
Windows 7 (32 and 64 bit)
PC Software
Microsoft .NET framework 4.0 (or later)
Microsoft Visual C++
10
8. Care and maintenance
Store and use TAGARNO AIR in a dry, clean and ventilated room.
Do not place TAGARNO AIR in direct sunlight, next to a radiator/heater
or somewhere where the apparatus may be subjected to liquids.
All plugs are designed to be used in one way only. Therefore you should
never use force when you connect the apparatus.
Remember to disconnect all elements if you intend to move TAGARNO
AIR.
If you move TAGARNO AIR from a cold to a hot room, you must wait at
least an hour before you turn it on in order to avoid short circuits due to
condensation.
Remove the cables by pulling the plug itself – never by pulling the cable.
If TAGARNO AIR needs repair, never do it yourself. Contact your distributor.
Manufactured by:
TAGARNO AS, Sandøvej 4, DK 8700 Horsens
+45 7625 1111, [email protected], www.tagarno.com
11
9. Cleaning recommendations
It is important to clean your TAGARNO AIR regularly to avoid a build-up
of dust and air-borne contaminants.
Non-optical areas of the instrument
Use a soft cotton cloth dipped in a soap solution to remove dirt and
grease from the non-optical areas of the instrument. A standard soap
solution consists of 200 ml of water and 5-7 drops of dishwasher
detergent.
To remove microorganisms from the surface, wet a soft cotton cloth
with a disinfectant solution and gently wipe the non-optical areas of
the instrument. TAGARNO AIR is compatible with a daily wipe-off with
a disinfectant solution consisting of 96 % ethanol or other solutions
containing alcohol, e.g. IPA products (Isopropyl Alcohol).
Optical components of the instrument: the lenses
Avoid cleaning the lens more than necessary as this involves the risk of
scratching the lens and leaving cleaning streaks. Only clean it when it is
visibly dirty. Also be careful not to touch the lens or to subject it to sharp
and hard objects.
Use an air brush to blow away dust or dirt particles from the lens surface. Gently, and with
minimal pressure, wipe the lens with a lens paper.
If you need to use any liquid to remove crud on the lens, use distilled
water or alcohol (Isopropyl Alcohol, 90 % pure). Put a drop or two of the
liquid on your lens paper and hold it against the lens for a few seconds
to dissolve the crud. Then gently wipe it free. Never apply the liquid
directly to the lens.
After using solvents, clean the lens again with standard distilled water to
ensure that you have removed all the solvents from the lens.
Manufactured by:
TAGARNO AS, Sandøvej 4, DK 8700 Horsens
+45 7625 1111, [email protected], www.tagarno.com
12