44” 3-in-1 Console (XL-2) - Whalen Furniture

Transcription

LOT NUMBER:
DATE PURCHASED:
/
/
44” 3-in-1 Console (XL-2)
This item is designed to be 3-in-1 configuration. Please choose which of the 3 options suits your
needs. DO NOT discard any of the hardware or parts that you will not use on your set option, this
will give you the opportunity to use this TV Console for different configurations in case you decide
to upgrade your TV set in the future.
Option 1
With Swinging Floater
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if you are missing parts, do not return this item to
the Retailer Store. Please call our toll-free customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
8:30 a.m. - 4:30 p.m. PST, Monday - Friday
ONLINE: www.whalenfurniture.com
EMAIL: [email protected]
Video Instruction Guides
Go to http://whalen.showuhow.com to view step-by-step instructional
videos for assembling and installing your product. Enter the following
product number on the ShowUhow homepage.
XL-2
Whalen Furniture Mfg. Inc.
Factory No. 33-10944
Page 1
Model # XL-2
I M P O R T AN T I N F O R M ATI O N
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
MANUFACTURER: Whalen Furniture
CATALOG: 44” 3-in-1 Console (XL-2)
DATE OF MANUFACTURE: July, 2010
MADE IN CHINA
FITS UP TO MOST 50” FLAT PANEL TV’S
MAXIMUM LOAD 135 lb. (61.2 kg)
FITS UP TO MOST 50” FLAT PANEL TV’S
WITHOUT SWIVELING BRACKET
THIS UNIT IS INTENDED FOR USE ONLY WITH THE PRODUCTS
AND MAXIMUM WEIGHTS INDICATED. USE WITH OTHER PRODUCTS OR PRODUCTS
HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY
CAUSING POSSIBLE INJURY. THE BASE OF THE TELEVISION MUST BE PLACED
SQUARELY IN THE CENTER OF THE STAND WITH NO OVERHANGING ON EITHER SIDE.
G E N E R AL I N F O R M ATI O N , TI P S & TR I C K S
1.
2.
3.
4.
5.
6.
7.
Please read the Assembly Instructions prior to assembling this product.
Remove all hardware from box and sort by size.
Check to see that all hardware and parts are present BEFORE assembling.
Ask a friend to assist you with the assembly of this furniture.
To avoid damage, assemble the product on a sturdy, level and protective surface.
Please wait until all steps are completed before tightening bolts.
Make sure all bolts are tightly fastened before the unit is used.
This product is sold with Tip Restraint Hardware kit. You must install the Tipping Restraint
Hardware between the wall and the TV stand to prevent any accidents or damages. When
properly installed, this restraint can provide protection against the unexpected tipping of the
unit due to small tremors, bumps or climbing. The restraint is only a deterrent and is not a
substitute for proper adult supervision. Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
Please call for replacement parts or assistance: 1-866-942-5362
Page 2
Model # XL-2
Parts and Hardware Master List
Please read completely through the instructions and verify that all parts listed are present
before beginning assembly.
A-Top Shelf Frame (1)
D- Long Spine (1)
B- Middle Shelf Frame (1)
C- Bottom Shelf Frame (1)
E- Left “L” Shape Leg (1)
D1- Short Spine (1)
F- Left Front Leg (1)
G- Right “L” Shape Leg (1)
H- Right Front Leg (1)
I- Top Glass Shelf (1)
J- Middle Glass Shelf (1)
K- Bottom Glass Shelf (1)
L- Swiveling Bracket (1)
O- Safety Bar (1)
M- XYZ Mounting Frame (1)
N- Monitor Bracket (2)
P- Decorative Rail (2)
Page 3
Model # XL-2
Parts and Hardware Master List
(1) - Suction Cup
(20+1 extra)
(2) - 3/4” Bolt
(18+1 extra)
(3) - 1 1/4” Bolt
(16+1 extra)
(4) - Hex Nut
(4+1 extra)
(5) -Black Lock Washer (6) - Zinc Lock Washer (7) – Black Flat Washer (8) - Zinc Flat Washer
(14+1 extra)
(14+1 extra)
(18+1 extra)
(14+1 extra)
(9)- Large Flat Washer
(6)
(13) - 1” Bolt
(4+1 extra)
(10) - 2 1/2” Lag Bolt
(6)
Open Wrench
(1)
(11) - Concrete Anchor (12) - Cable Control
(6)
(2)
Allen Wrench
(1)
Tipping Restraint Hardware Kit (1)
(Inside Plastic Bag)
TV Mounting Kit
M4 x 12 Bolt (4)
M6 x12 Bolt (4)
M4 Lock Washer (4)
M4 x 30 Bolt (4)
M6 x 35 Bolt (4)
M5 Lock Washer (4)
M5 X 12 Bolt (4)
M8x16 Bolt (4)
M6 Lock Washer (4)
M5 x 30 Bolt (4)
M8 x40 Bolt (4)
M8 Lock Washer (4)
Large Spacer (4)
Small Spacer (4)
M4/M5 Flat Washer (8)
M6/M8 Flat Washer (4)
Tools required: Allen Wrench (provided) and Open Wrench (provided), Phillips Head
Screwdriver, Mallet, Power Drill, 3/8” & 3/16”Drill Bit, Socket Wrench Adapter with
Socket Set, 1/2” Masonry Bit for brick concrete, Stud Sensor.
Page 4
Ass embl y Instructions for Option #1:
Console with Swinging Floater
Model # XL-2
Note: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled,
go back and fully tighten all bolts. This will make it easier during assembly of unit.
1. Unpack the unit and confirm that you have all the hardware and required parts listed.
2. Align the bottom bracket holes of Left “L” Shape Leg (E) with the sockets on the Left Front
Leg (F). Make sure the upper tube of “L” Shape Leg fits into the cutout of Left Front Leg
properly. Attach in place by inserting two 3/4” Bolts (2) with Black Washers (5 & 7) into the
bracket holes. Tighten the bolts with Allen Wrench provided. See detail #1.
3. Repeat last step to combine the Right “L” Shape Leg (G) with Right Front Leg (H) together.
4. Attach 2 Decorative Rails (P) to the bottom of Long Spine (D) using six 1 1/4” Bolts (3).
Tighten with Allen Wrench provided. See detail #1A.
Required hardware in this step
Description:
(2) – 3/4” Bolt
(3) – 1 1/4” Bolt (5) – Black Lock Washer (7) – Black Flat Washer
Sketch
Qty.
(4 pcs)
(6 pcs)
(4 pcs)
(4 pcs)
Tools required: Allen Wrench
Page 5
Model # XL-2
Assembly Instructions for Console with Swinging Floater
5. Locate the Long Spine (D) on a scratch free surface with 2 round holes facing up as shown
in detail #2.
6. Align the holes on back rail of 3 Shelf Frames (A, B & C) with the sockets on the Long Spine
(D). Insert and screw 1 1/4” Bolts (3) with Zinc Lock Washers & Flat Washers (6 & 8)
through the pre-drilled holes on back rail into the Spine. Make sure the corner plates for
Suction Cup on each Shelf Frame will face up after assembly. See detail #2.
Description:
(3) – 1 1/4” Bolt
(6) – Zinc Lock Washer
(8) – Zinc Flat Washer
(6 pcs)
(6 pcs)
(6 pcs)
Sketch
Qty.
Page 6
Model # XL-2
7. Stand the unit upright.
8. Align and attach Left Leg Assembly to the Top Shelf Frame (A) using two 1” Bolts (13) with
Zinc Washers (6 & 8) through the pre-drilled holes on inner side rail into the top of both Legs.
See detail #3. DO NOT tighten the bolts.
9. Secure Left Leg Assembly to Middle & Bottom Shelf Frame (B & C) using the 1 1/4” Bolts (3)
with Zinc Washers (6 & 8) from inside the shelf frame into the sockets included on the side
of Legs. See detail #3A.
10. Repeat last 2 steps to attach Right Leg Assembly at the other end.
Description: (13)- 1” Bolt
(3) – 1 1/4” Bolt
(6) – Zinc Lock Washer (8) – Zinc Flat Washer
Sketch
Qty.
(4 pcs)
(4 pcs)
(8 pcs)
(8 pcs)
Page 7
Model # XL-2
11. Go back and tighten all bolts with Allen Wrench provided.
12. In case of uneven floor, Floor Levelers are provided at the bottom of both Front Legs (F & H).
Simply tilt the unit back and raise or lower floor leveler by hand to correct tilting as shown in
detail #4.
Hardware provided
Tools required
Pre-attached Floor Leveler
No tool required
Page 8
Model # XL-2
13. Align and attach Swiveling Bracket (L) to the top of Long Spine (D) using six 3/4” Bolts (2)
with Black Washers (5 & 7). Make sure the swivel bolt head is up. See detail #5.
Note: The Spine can provide four height options for your TV set. Refer to your TV size, adjust
the Swiveling Bracket at your desired height to offer optimum viewing.
Description:
(2) - 3/4” Bolt
(5) – Black Lock Washer
(7) – Black Flat Washer
Sketch
Qty.
(6 pcs)
(6 pcs)
(6 pcs)
Page 9
Model # XL-2
14. Hold the flat side of XYZ Mounting Frame (M) onto the Swiveling Bracket (L) ensuring the
hook on the side of Mounting Frame is bottom. Align and attach by threading four 3/4” Bolts
(2) with Black Flat Washers (7) through the metal plate on XYZ Mounting Frame and the
Swiveling Bracket, at the other side of Swiveling Bracket place the other Black Flat Washers
(7) and Black Lock Washers (5), and then secure with Hex Nuts (4). Securely tighten with
Open Wrench and Allen Wrench provided. See detail #6.
Description:
(2) - 3/4” Bolt
(4) - Hex Nut (5) – Black Lock Washer (7) -Black Flat Washer
Sketch
Qty.
(4 pcs)
(4 pcs)
(4 pcs)
(8 pcs)
Tools required: Allen Wrench and Open Wrench
Page 10
Model # XL-2
Mounting Monitor Bracket to a television with a flat back
Note: For televisions with a curved back or recessed back proceed directly to step #18.
15. Determine the correct diameter of the bolt your TV requires by hand threading them into the
threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If
you are unable to find the correct bolt consult a local hardware store.
16. Once you have determined the correct diameter Bolt, follow the appropriate Diagram below,
thread the Short Bolt through the appropriate Lock Washer, Flat Washer, the Monitor Bracket
(N), and into the upper threaded inserts of TV. As shown in detail #7A. Note: Lean the TV up
against a wall or other solid surface when attaching with the Monitor Brackets (N). DO NOT
place the TV face down on the glass this may cause permanent damage.
17. Proceed to insert the long Bolt through the appropriate Lock Washer, the Flat Washer, the
slot of Monitor Bracket (N), a second Flat Washer (M4/M5 Diameter Bolts only), appropriate
Spacer, and into the bottom threaded inserts of TV. As shown in detail #7. Make sure the
Monitor Brackets (N) are centered and level with each other. Tighten the bolts securing the
Monitor Brackets to the TV.
Parts provided
Qty.
Tools required
N – Monitor Bracket
TV Mounting Kit
(2)
Phillips Screwdriver
Page 11
Model # XL-2
Mounting Monitor Bracket to a television with a curved / recess back
18. Determine the correct diameter of the bolt your TV requires by hand threading them into the
threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If
you are unable to find the correct bolt consult a local hardware store.
19. Once you have determined the correct diameter Bolt, follow the appropriate Diagram below,
thread the Bolt through the appropriate Lock Washer, the Large Flat Washer, the Monitor
Bracket (N), a second Large Flat Washer (M4/M5 Diameter Bolts only), appropriate Spacer
and into the threaded inserts of TV. See detail #8.
20. Make sure the Monitor Brackets (N) are vertically centered and level with each other. Tighten
the bolts to secure the Monitor Brackets to the TV.
Page 12
Model # XL-2
MAKE SURE ALL BOLTS ARE TIGHT AND SPINE IS AT A 90 DEGREE ANGLE
PRIOR TO INSTALLATION OF TV.
21. Once the Monitor Brackets (N) are attached onto the back of television, ask for assistance
to lift the television up to the XYZ Mounting Frame (M). Place the hooks on Monitor Brackets
over the Mounting Frame then lower them onto the bars of Mounting Frame. Proceed to
center the television.
22. Insert the Safety Bar (O) into the bottom holes on the side of XYZ Mounting Frame (M) by
sliding it all the way across the frame. Secure the Safety Bar by rotating the bent end into
the slot of hook so that it is facing backward. Make sure it sits over the bottom hook of the
Monitor Brackets. See detail #9.
Parts provided
Qty.
Tools required
O - Safety Bar
(1)
No tool required
Page 13
Model # XL-2
23. Attach 2 Cable Controls (12) onto the backside of Spine (D) with the 3/4” Bolts (2). Tighten
the bolts with Allen Wrench provided. See detail #10.
24. The Cable Controls (12) enable you to shorten, separate and route both single and bundled
cables. Using the Cable Controls you can create a system for routing cables through
channels, between components and to power sources without usual tangled mess or
annoying signal interference. As shown in detail #10A.
Description:
(2) - 3/4” Bolt
(12) – Cable Control
(4 pcs)
(2 pcs)
Sketch
Qty.
Page 14
Model # XL-2
25. Put Suction Cups (1) firmly into the top holes and corner plates on 3 Shelf Frames (A, B & C)
as shown in detail #11.
26. Place Top Glass (I) and Glass Shelves (J & K) in place as shown in detail #11. Make sure
the glass is properly centered and the black side of glass is down. Push each glass all the
way back against the Spine. Also, be sure to press down evenly and firmly each glass onto
the Suction Cups to make sure they securely rest onto the Suction Cups.
Note: Make sure that the Suction Cups go all the way into the pre-drilled holes to prevent the
glass shelf from falling and getting damage. If glass is scratched you can minimize the
damage by using a BLACK marker and filling in scratched area from underneath.
Description
Sketch
(1) – Suction Cup
Qty.
(20 pcs)
Page 15
Model # XL-2
TIPPING RESTRAINT HARDWARE
Note: We have included one Tipping Restraint Hardware bag for this unit.
When properly installed, this restraint can provide protection against the unexpected tipping
of the unit due to small tremors, bumps or climbing. We strongly recommend mounting this
hardware to a wall stud and your unit when installing.
Please carefully read the instructions printed on the plastic bag.
Note: You must install the Tipping Restraint Hardware with the unit in use to prevent
any accidents or damage to the unit.
Tools required: Allen Wrench (provided), Phillips Screwdriver, Mallet, Power Drill, and 3/8” Drill Bit.
Page 16
Model # XL-2
As s e m b l y I n s t r u c t i o n s f o r O p t i o n # 2 - 3 :
C o n s o l e w i t h U n i ve r s a l W a l l M o u n t
27. Align the bottom bracket holes of Left “L” Shape Leg (E) with the sockets on the Left Front
Leg (F). Make sure the upper tube of “L” Shape Leg fits into the cutout of Left Front Leg
properly. Attach in place by inserting two 3/4” Bolts (2) with Black Washers (5 & 7) into the
bracket holes. Tighten the bolts with Allen Wrench provided. See detail #12.
28. Repeat last step to combine the Right “L” Shape Leg (G) with Right Front Leg (H) together.
Description:
(2) - 3/4” Bolt
(5) – Black Lock Washer
(7) – Black Flat Washer
Sketch
Qty.
(4 pcs)
(4 pcs)
(4 pcs)
Page 17
Model # XL-2
Assembly Instructions for Table-top
29. Locate Short Spine (D1) on a scratch free surface with 2 round holes facing up as shown in
detail #13.
30. Align the holes on back rail of 3 Shelf Frames (A, B & C) with the sockets on the Short Spine
(D1). Insert and screw 1 1/4” Bolts (3) with Zinc Lock Washers & Flat Washers (6 & 8)
through the pre-drilled holes on back rail into the Spine. Make sure the corner plates for
Suction Cup on each Shelf Frame will face up after assembly. See detail #13.
Description:
(3) – 1 1/4” Bolt
(6) – Zinc Lock Washer
(8) – Zinc Flat Washer
(6 pcs)
(6 pcs)
(6 pcs)
Sketch
Qty.
Page 18
Model # XL-2
31. Stand the unit upright.
32. Align and attach Left Leg Assembly to the Top Shelf Frame (A) using two 1” Bolts (13) with
Zinc Washers (6 & 8) through the pre-drilled holes on inner side rail into the top of both Legs.
See detail #14. DO NOT tighten the bolts.
33. Secure Left Leg Assembly to Middle & Bottom Shelf Frame (B & C) using the 1 1/4” Bolts (3)
with Zinc Washers (6 & 8) from inside the shelf frame into the sockets included on the side
of Legs. See detail #14A.
34. Repeat last 2 steps to attach Right Leg Assembly at the other end.
Description: (13)- 1” Bolt
(3) – 1 1/4” Bolt
(6) – Zinc Lock Washer (8) – Zinc Flat Washer
Sketch
Qty.
(4 pcs)
(4 pcs)
(8 pcs)
(8 pcs)
Page 19
Model # XL-2
35. Go back and tighten all bolts with Allen Wrench provided.
36. In case of uneven floor, Floor Levelers are provided at the bottom of both Front Legs (F & H).
Simply tilt the unit back and raise or lower floor leveler by hand to correct tilting as shown in
detail #15.
Hardware provided
Tools required
Pre-attached Floor Leveler
No tool required
Page 20
Model # XL-2
37. Attach 2 Cable Controls (12) onto the backside of Spine (D1) with the 3/4” Bolts (2). Tighten
the bolts with Allen Wrench provided. See detail #16.
38. The Cable Controls (12) enable you to shorten, separate and route both single and bundled
cables. Using the Cable Controls you can create a system for routing cables through
channels, between components and to power sources without usual tangled mess or
annoying signal interference. As shown in detail #16.
Description:
(2) - 3/4” Bolt
(12) – Cable Control
Sketch
Qty.
(4 pcs)
(2 pcs)
Page 21
Model # XL-2
39. Put Suction Cups (1) firmly into the top holes and corner plates on 3 Shelf Frames (A, B & C)
as shown in detail #17.
40. Place Top Glass (I) and Glass Shelves (J & K) in place as shown in detail #17. Make sure
the glass is properly centered and the black side of glass is down. Push each glass all the
way back against the Spine. Also, be sure to press down evenly and firmly each glass onto
the Suction Cups to make sure they securely rest onto the Suction Cups.
Note: Make sure that the Suction Cups go all the way into the pre-drilled holes to prevent the
glass shelf from falling and getting damage. If glass is scratched you can minimize the
damage by using a BLACK marker and filling in scratched area from underneath.
Description
Sketch
(1) – Suction Cup
Qty.
(20 pcs)
Page 22
Model # XL-2
41. Position the assembled Table-top in your desired location against the wall. Now follow the
instructions printed on the plastic bag in order to mount the Tipping Restraint Hardware Kit to
the Spine properly. As shown in detail #18.
NOTE: YOU MUST USE THIS TIPPING RESTRAINT TO ATTACH THIS UNIT TO
THE WALL, TO PREVENT ACCIDENTS AND/OR INJURIES.
42. The Table-top is ready for use now if you only want to place the TV on the console top. Be
sure to position your TV in center of console with no overhang on either side.
Page 23
Model # XL-2
The following steps are only for those who wish to mount their
TV directly to the wall. If you have already mounted your TV to
the Swinging Floater or plan to display your TV on the top
surface of the stand, disregard the following steps.
Assembly Instructions for Universal Wall Mount
Installing XYZ Mounting Frame onto WOODEN STUD WALL
43. The XYZ Mounting Frame (M) must be mounted to two Wood Studs at least 12” apart, using
a high quality Stud Finder to locate the two adjacent studs. After you have located the studs,
verify with a nail for added security. See detail #19A.
44. Pre-drill a 2 1/2" deep hole at the desired height in each stud using a 3/16” drill bit, make
sure that the holes are centered in the studs and level with each other. Use the XYZ
Mounting Frame (M) as a template to mark the corresponding location for the bottom holes in
each stud, drill holes 2 1/2" deep with the 3/16” drill bit at the marked location.
45. Orient the Mounting Frame with the “C” plate against the wall, and using four Lag Bolts (10)
with Large Flat Washer (9) through the slots of “C” Plate on Mounting Frame into the holes in
the wall, secure the mounting frame to the wall as shown in detail #19B.
Do not over tighten the Lag Bolts. Tighten Lag Bolts only until the Lag
Bolt Washer is pulled firmly against the “C” Plate of Mounting Frame. If there is a layer of
drywall or other material, this drywall or other material may not exceed 5/8 inch in
thickness. Failure to heed this caution may result property damage and/or personal injury.
Hardware provided
Sketch
Qty.
(9) – Large Flat Washer
(4)
(10) –2 1/2” Lag Bolt
(4)
Tools required
Stud Sensor, Mallet, Power Drill, 3/16” Drill Bit, Socket Set
Page 24
Model # XL-2
Assembly Instruction for installing XYZ Mounting Frame onto BRICK, SOLID
CONCRETE OR CONCRETE BLOCK
46. Use the XYZ Mounting Frame (M) as a template, mark six holes location on the wall, three in
the top row and three in the bottom row of slots. Make sure that the holes are level and there
is at least 6” between any two holes, pre-drill these holes with a 1/2” masonry bit to at least
2 1/2” in depth.
47. Insert a Concrete Anchor (11) into each of these holes; make sure they are completely
seated and flush with the concrete surface, even if there is a layer of drywall or other material
in front of the concrete.
48. Attach the XYZ Mounting Frame (M) to the wall using six Lag Bolts (10) and Large Flat
Washers (9) through the slot of “C” Plate on Mounting Frame into the Concrete Anchors (11)
in the wall as shown in detail #20. Make sure the back hook of Mount Frame is bottom.
Maximum weight 165 lb (74.8 kg)
Concrete Anchors should only be used for masonry mounting.
NEVER use the wall anchors to mount the unit to drywall.
Hardware provided
Sketch
Qty.
(9) – Large Flat Washer
(6)
(10) – Lag Bolt
(6)
(11) –Concrete Anchor
(6)
Tools required: Mallet, Power Drill, 1/2” Masonry Bit for brick concrete, Socket Set
Page 25
Model # XL-2
Assembly Instructions for Universal Wall Mount
49. Once the Monitor Brackets (N) are attached onto the back of television, ask for assistance to
lift the television up to the XYZ Mounting Frame (M). Place the hooks on Monitor Brackets
over the Mounting Frame then lower them onto the bars of Mounting Frame. Proceed to
center the television.
50. Insert the Safety Bar (O) into the bottom holes on the side of XYZ Mounting Frame (M) by
sliding it all the way across the frame. Secure the Safety Bar by rotating the bent end into the
slot of hook so that it is facing wall. Make sure it sits over the bottom hook of the Monitor
Brackets. See detail #21.
51. Place assembled console under your TV set as shown in detail #21A.
Parts provided
Qty.
Tools required
O - Safety Bar
(1)
No tool required
Page 26
Model # XL-2
Care and Maintenance










Use a soft, clean cloth that will not scratch the surface when dusting.
Use of furniture polish is not necessary. Should you choose to use polish, test in an
inconspicuous area first.
Using solvents of any kind on your furniture may damage the finish.
Never use water to clean your furniture as it may cause damage to the finish.
Always use coasters under beverage glasses and flowerpots.
Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently.
Avoid rubbing.
Always use protective pads under hot dishes and plates. Heat can cause chemical changes
that may create spotting within the furniture finish.
Stains or marks from crayons or ink markers will be difficult to remove.
In the event that your furniture is stained or otherwise damaged during use, we recommend
that you call a professional to repair your furniture.
Check bolts/screws periodically and tighten them if necessary.
Further advice about wood furniture care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and
humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep
furniture away from direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Follow these important and
helpful tips that will enhance your furniture as it ages.
We hope you enjoy your purchase for many years.
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we
will repair or replace it for up to one (1) year from date of purchase. Every Whalen
Furniture product is designed to meet your highest expectations. We guarantee that you
will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which
vary from State to State.
Customer Service: 1-866-942-5362
8:30 a.m. - 4:30 p.m. PST, Monday to Friday
www.whalenfurniture.com
Page 27
*XL-2-1-LS
*XL-2-2-TSF
*XL-2-3-MSF
*XL-2-4-BSF
*XL-2-5-LFL
*XL-2-6-LLSL
*XL-2-7-RFL
*XL-2-8-RLSL
*XL-2-9-DR
*XL-2-10-TGS
*XL-2-11-MGS
*XL-2-12-BGS
*XL-2-13-CH
*XL-2-14-3/4B
*XL-2-15-1 1/4B
*XL-2-16-BLW
*XL-2-17-ZLW
*XL-2-18-BFW
Zinc Flat Washer
Large Flat Washer
2 1/2" Lag Bolt
1 3/4" Concrete Anchor
Hex Nut
Open Wrench
Allen Wrench
Suction Cup
Cable Control
Small Spacer
Large Spacer
M4/M5 Flat Washer
M6/M8 Flat Washer
M4 Lock Washer
M5 Lock Washer
M6 Lock Washer
M8 Lock Washer
M4 x 12 Bolt
M4 x 30 Bolt
44" 3-in-1 Console (XL-2)
*XL-2-19-ZFW
*XL-2-20-LFW
*XL-2-21-2 1/2LB
*XL-2-22-1 3/4CA
*XL-2-23-HN
*XL-2-24-OW
*XL-2-25-AW
*XL-2-26-SC
*XL-2-27-CC
*XL-2-28-SS
*XL-2-29-LS
*XL-2-30-M4M5FW
*XL-2-31-M6M8FW
*XL-2-32-M4LW
*XL-2-33-M5LW
*XL-2-34-M6LW
*XL-2-35-M8LW
*XL-2-36-M4x12B
*XL-2-37-M4x30B
*XL-2-38-M5x12B
*XL-2-39-M5x30B
*XL-2-40-M6x12B
*XL-2-41-M6x35B
*XL-2-42-M8x16B
*XL-2-43-M8x40B
*XL-2-44-TRHK
*XL-2-45-FL
*XL-2-46-RPG
*XL-2-47-OPG
*XL-2-48-PEC
*XL-2-49-PC
*XL-2-50-MF
*XL-2-51-MB
*XL-2-52-SB
*XL-2-53-SB
*XL-2-54-SS
*XL-2-55-SEC
*XL-2-56-1B
IF YOU REQUIRED TO ORDER PARTS PLEASE USE THE LIST BELOW
Long Spine
Top Shelf Frame
Middle Shelf Frame
Bottom Shelf Frame
Left Front Leg
Left "L" Shape Leg
Right Front Leg
Right "L" Shape Leg
Decorative Rail
Top Glass Shelf
Middle Glass Shelf
Bottom Glass Shelf
Complete Hardware
3/4” Bolt
1 1/4” Bolt
Black Lock Washer
Zinc Lock Washer
Black Flat Washer
M5 x 12 Bolt
M5 x 30 Bolt
M6 x 12 Bolt
M6 x 35 Bolt
M8 x 16 Bolt
M8 x 40 Bolt
Tipping Restraint Hardware Kit
Floor Leveler
Round Plastic Grommet
Oval Plastic Grommet
Plastic End Cap (20x40)
Plastic Cover
XYZ Mounting Frame
Monitor Bracket
Swiveling Bracket
Safety Bar
Short Spine
Spine End Cap (40x80)
1” Bolt

44” 3-in-1 Console (XL-2) - Whalen Furniture

Transcription

Similar documents

MotoTec Solar Go-kart Assembly Manual

Part # 11201099 82-92 Camaro Front CoolRide kit

Honda XR650L Pannier Racks

Brake Kit Content Sheet

2013 GM 3500 Cutaway 2-Stage Rear Air Suspension

assembly instruction - Numark Customer Service

Assembly Instructions

Rivnut Installation Instructions

3-IN-1 TV Console Model # BBXL54NV

Scott Tailwheel 3200 on PA22/20