PANELIZE YOUR DREAMS

Transcription

PANELIZE YOUR DREAMS
Panelize your dreams
T h e
B e t t e r
W a y
t o
B u i l d !
Structural
insulated
panels
(SIPS)
Enercept SIPS are custom
made to reflect your
vision for the energy
efficient home of your
dreams.
Experience Enercept -
the better way to build!
Independent Dealer contact information:
The Builders’ Choice
605-882-2222
www.enercept.com
Why Build With Enercept Structural Insulated Panels (SIPS)?
1. SUPER ENERGY EFFICIENCY - Save 40% or more on heating and cooling costs
2. BUILDER FRIENDLY - Factory-installed connecting posts with rounded edges for easier installation
3. QUICKER CONSTRUCTION CYCLE - Move in earlier with one step framing, sheathing and insulating
4. LESS ON-SITE WASTE - Window and door openings are cut at the factory and framed with headers in place
5. GREEN - Made with oriented strand board (OSB), very little lumber
6. REDUCED MATERIAL THEFT - Panels of little use to would-be thieves
7. HEALTHIER INDOOR AIR QUALITY - Less air infiltration keeps clean air in and allergens/dust out
8. QUIET - Wind and other outside noises are greatly reduced with Enercept SIPs
9. LEED AND ENERGY STAR COMPATIBLE - Earn up to 21.5 LEED® for Home™ points; qualify for the Energy Star rating
10. 2 1/2 TIMES STRONGER THAN STICK-BUILT & CODE CERTIFIED - ICC #ESR-1780/NTA #ENR0120-21
11. ORIGINAL HOLDER OF TWO PATENTS - Insulated connecting posts and factory-installed electrical chases
12. CUSTOMER SERVICE YOU CAN DEPEND ON - From estimate to completion and beyond, Enercept will be here to help
Page 2
f r e q u e n t ly a s k e d q u e s t i o n s
The Builders’ Choice
√
WHAT ARE STRUCTURAL INSULATED PANELS (SIPS)?
SIPs are a high performance building system for all types of construction. The panels consist of a structural foam (insulating) core bonded between two
structural skins. Enercept SIPs typically use expanded polystyrene (EPS) for the insulating core and oriented strand board (OSB) for the exterior and
interior skins. SIPs are manufactured under factory-controlled conditions and can be fabricated to fit nearly any building design. The result is a costeffective structure that is energy efficient and 2 1/2-times stronger than stick-built.
√
HOW DOES THE COST OF A SIPS STRUCTURE COMPARE TO STICK-BUILT?
When factoring in material cost, labor expense, job site waste and the lifetime benefit of energy savings, the Enercept system is the lowest cost building
solution.
√
DO ENERCEPT PANELS CONTAIN UREA-FORMALDEHYDE (UF) OR
CHLOROFLUOROCARBONS (CFC’S)?
No. Enercept SIPs were tested at the University of South Dakota; no traces of UF were detected. The panels do not contain CFCs and do not produce
off-gassing of dangerous chemicals.
√
WHAT IS THE R-VALUE OF ENERCEPT PANELS?
There are three methods of heat transfer: convection, conduction and radiation. R-value is the measure of resistance to heat loss by conduction only.
The most important factor in thermal efficiency is the continuity of the insulation. The Enercept system results in a solid envelope of insulation where
even the connecting posts have a foam core.* The Enercept system has the ability to resist heat transfer by both conduction and convection (air
movement). Based on this information, a conventional stick-built home would require a R-40 wall to compete with a 6-inch Enercept wall (R-24).
√
IS AN ENERCEPT ROOF VENTED?
A ventilated roof is not necessary in most climates – as once thought. Model codes allow both vented (cold roof) and unvented (hot roof) roof
assemblies. Because SIPs roofs are insulated, conductive heat loss is avoided - negating the problems usually associated with an unvented roof. If the
roof must be ventilated, 2x strips can be attached to the roof and then covered with sheathing to form a vented layer over the panels.
√
HOW IS AN ENERCEPT STRUCTURE WIRED?
Enercept was the first company to patent factory-installed electrical chases. Chases are usually marked on the interior sheathing of the panels for easy
identification. Enercept roof panels are typically pre-wired in the factory per customer specifications. Simply drill access holes through the sill and top
plates for access to the electrical chases. A comprehensive electrical guide is available.
√
DO ENERCEPT HOMES HAVE MOISTURE PROBLEMS?
Enercept structures are very airtight compared to other building methods. Generally a moisture barrier, like house wrap, is applied to the exterior of
the structure. Seam tape is provided for all interior panel connections and the use of an air exchanger is recommended. These measures will protect
the home from moisture and will create exceptional indoor air quality.
√
IS THE ENERCEPT SYSTEM CODE APPROVED AND WARRANTED?
The Enercept building system has been accepted for use by HUD and is ICC/ICBO approved. Enercept SIPs have been third-party tested by
independent testing agencies - RADCO and NTA, Inc. Enercept offers a limited lifetime warranty (copies available upon request).
*standard 4’ wide panels
MADE IN THE USA
Looking for a spacious vaulted ceiling?
I-Joist Connection
The Enercept structural roof system offers the choice of an insulated attic space or
vaulted ceilings that will create the impression of more living space with the
option of including a loft area.
SIPs can be made to a maximum of 8-feet wide and 24-feet long. A panel this
large can cover a lot of area quickly. A SIPs roof thickness of 14 -inches will
provide optimal protection from summer heat and winter cold.
A structural I-Joist connector is factory installed at each splice for easier
construction.
For easier assembly, roof panels are pre-wired according to customer
specifications.
“This is our third building, I would not
build with anything else.”
Shade’ Vineyards, Volga, SD
Page 4
E n e r c e p t r o o f pa n e l s
T h e
B e t t e r
W a y
t o
B u i l d !
The Builders’ Choice
“We found the ease and speed of
construction unmatched by any other
method of construction or product.”
A.J.H., Walloon Lake, MI
Enercept Gable Panels
Gable panels are manufactured to the precise pitch of the roof.
All beams, wall-to-wall panel ties and roof screws are included in
the Enercept roof package.
Roof panel thickness will vary, depending on the design load and
R-value needs of the geographic area.
Usable square footage
Fully vaulted ceilings provide usable square footage, as shown
in this bedroom loft area.
Page 5
Enercept wall system:
The Enercept wall system is typically comprised of 5 1/2-inch EPS insulation
laminated between OSB structural skins.
Enercept 4-foot panels are connected at the job site by a tongue-and-groove
method with factory-installed insulated posts (originally patented by Enercept).
All rough openings (windows and doors) are custom built and framed in the
factory.
Electrical chases and knock-out boxes are factory installed using the Enercept
patented system.
Bottom sill plates, top plates and panel sealant are all included with your Enercept
building package.
To make jobsite assembly easier, Enercept includes a laminated
diagram and construction guide with every order.
Page 6
E n e r c e p t wa l l pa n e l s
T h e
B e t t e r
W a y
t o
B u i l d !
The Builders’ Choice
Enercept sips are the
most fully
customized sips on
the market.
Newman house: SIPA honorable
mention award winner for 2012
“Our Enercept home is so air
tight that even after two
months away, there is no dust
on the furniture.”
J. Cillessen, Colorado
↑ patented connecting
post system
← corner adjustment
panel
Page 7
COVER MORE SQUARE FEET IN LESS TIME WITH JUMBO PANELS
Enercept 8-foot wide jumbo
wall and roof panels are custom
made with the same great
features of the Enercept 4-foot
wide panel:

Roof panels are pre-wired.

Wall panels are available
with window and door
openings that are bucked
out.
When installed horizontally, as
an 8-foot high wall, framing,
insulating and sheathing a
24-foot span wall is possible
with just one panel. This
process drastically reduces the
time required to assemble
larger structures.
Jumbo panel with spline connection ↓
Page 8
E n E r c E p t 8 ’ x 2 4 ’ J U M B O pa n E l s
T h e
B e t t e r
W a y
t o
B u i l d !
The Builders’ Choice
Rough openings precision cut with
our fully automated Hundegger Saw
Eight-foot roof panels
8-foot wide wall panel with factory-installed window
openings placed horizontally to cover more linear feet
Enercept 8-foot wide panels have been third party tested for strength by NTA, Inc. When required,
Enercept 8-foot wide panels can be engineered to meet your specific requirements.
ENERCEPT BASEMENT PANELS
Enercept offers two types of below-grade SIPs:

Basement

Foundation
The Enercept basement system creates an insulated environment perfect for additional living
space. A solid core of 7-1/4” EPS insulation
prevents the cold from creeping into the
conditioned space. The result is a warm, dry
basement with the feel of main floor comfort.
The typical basement panel is comprised of
7-1/4” EPS insulation with 1/2” treated plywood
exterior sheathing and 7/16” OSB interior
sheathing. Green treated 2x8 lumber is placed
12” on center. Panels are connected by a
preinstalled 2x8 which fits into the recessed edge
of the adjoining panel. Sealant (supplied by
Enercept) is applied at the time of construction
to the bottom sill plate and between panels.
Vertical electrical chases are factory routed in
each panel. All window openings are precut and
framed by Enercept.
The
prebuilt
nature of
the
Enercept
basement
system
allows for
fast construction and eliminates the need to
fur-out the walls.
Page 10
E n e r c e p t b e l o w- g r a d e pa n e l s
T h e
B e t t e r
W a y
t o
B u i l d !
The Builders’ Choice
FOUNDATION PANELS
The EPS insulation in the Enercept foundation system protects
plumbing from freezing in cold climates.
Accessories for both systems include:
•Treated 2x bottom plate
•Sealant
•Double 2x top plate
•Optional rubber membrane
•Window framing anchors (basements)
Enercept foundation panels contain 5-5/8” or 7-3/8” EPS
insulation laminated between 1/2” treated plywood sheathing.
Green treated 2x lumber is placed 16” on center. Panels are
connected by a preinstalled 2x that fits into the recessed
edge of the adjoining panel.
Typical foundation panel height is 4’ unless otherwise specified.
To achieve the same thermal efficiency as an Enercept foundation
panel, a concrete wall would have to be at least 12’ thick!
Benefits of Green Construction:
☼ Clean
☼ Healthy
☼ Durable
☼ Marketable
☼ Comfortable
☼ Lower Environmental Impact
☼ Lenders may offer special financing incentives for
environmentally-friendly homes
Energy efficient
utility room
Blower Door Test
LEED Platinum home built with Enercept SIPs. This home, owned
by Paul Theis, boasts a HERS Index of only 17 and incorporates an
active solar, radiant heat system. Paul says, “we absolutely love our
Enercept home.”
Photo courtesy of SIPerior Homes (formerly Building Alternatives),
Woodland Park, CO
HERS and Energy Star®
WHAT IS A HOME ENERGY RATING SYSTEM (HERS)?
A HERS Rating is an official analysis of a home’s energy performance. The process involves an analysis of a home’s construction plans and on-site inspections. Included are an assessment of building components, performance testing (Blower
Door & Duct Blaster tests) and energy modeling with accredited software and a HERS Report.
WHAT IS THE HERS INDEX?
The HERS Index is the official number that comes from the rating. The scoring system was established by the Residential
Energy Services Network (RESNET). The scoring system compares the home being tested to a HERS Reference Home
which has a HERS Index of 100 (based on 2006 International Energy Conservation Code). A home with a HERS Index of
85 is 15% more energy efficient and qualifies for the Energy Star Label. Each 1-point decrease in the HERS Index is equal
to a 1% reduction in energy consumption. A Net-Zero energy home will have a HERS Index of zero.
CALL ENERCEPT AT 605-882-2222 FOR MORE INFORMATION, AND ACTUAL HERS
RATINGS OF HOMES BUILT WITH ENERCEPT SIPS.
Page 12
Enercept Sips are green
T h e
B e t t e r
W a y
t o
B u i l d !
The Builders’ Choice
The Enercept “Environmentally Friendly” Building System
Tree conservation - Made with OSB produced from fast growing, underutilized and
less expensive trees grown on tree farms.
Recycling - Scrap foam and wood from our production cycle is ground and recycled.
Less on-site waste - Less stress on area land fills.
Energy savings - Save up to 60% in energy costs compared to conventionally stickbuilt structures of comparable size.
Healthy home environment - Enercept structures are airtight, reducing the
unwanted transmission of outside allergens and dust.
Ideal for Passive House Designs
No CFCs or Urea-Formaldehyde
FOAM FACTS:
The foam of a coffee cup that protects your fingers from the hot liquid inside
is only 1/8” thick.
175°
An ice chest made with 1” foam will hold ice for up to 5 days
85°
Enercept SIP walls and roofs are manufactured with a foam insulating core
that can be up to 14” thick, providing ultimate protection against heat and
cold.
The Closer You Look … The Better We Look!
Page 13
Life of a project
T h e
B e t t e r
W a y
t o
B u i l d !
SIX KEY STEPS TO THE ENERCEPT PROJECT PROCESS
1) GETTING AN ESTIMATE:

Contact your local dealer and regional sales manager (RSM) to discuss the benefits of the Enercept building system

Send your plan to Enercept.

Enercept will review your plan and generate a FREE preliminary estimate.

The estimate will be sent to you via mail or email.
2) DRAFTING DOWN PAYMENT:

Review your estimate. If you have any questions or if revisions are required, please contact your independent dealer or sales manager.

Once you are satisfied the estimate is correct based on your parameters, a drafting down payment of $500 is required to proceed with
the approval drawing process. If engineering is required, the amount of the required drafting down payment is determined on a per
project basis. The drafting down payment can be in the form of a check or credit card (Note: when using the credit card option, a 4%
service fee will be added on charges above $1,000). Your drafting down payment will be credited to the final cost of your project and
reflected on your final invoice.
3) APPROVAL DRAWINGS AND PROPOSAL:

Your project will be assigned to an Enercept drafter who will work with you to generate approval drawings and help guide you through
the panel design process.

A proposal will be generated based on the approval drawings and sent to you for review.
4) VERIFY YOUR DRAWINGS:

You will then verify (check) your drawings and redline them as necessary.

You are encouraged to contact your dealer, RSM or drafter with questions.

Sign, date and return your redlined approval drawings, proposal and builder acknowledgement to Enercept with the required down
payment (typically 1/3 of the total project cost) in the form of a check or wire transfer.

IMPORTANT: No delivery commitments can or will be made until the final approval drawings, proposal and
builder acknowledgement along with the production down payment have been received by Enercept.
5) PRODUCTION AND SHIPMENT:

Upon receipt of the down payment, signed proposal and signed approval drawings, your project will be placed in the production
schedule. Once it’s in the production schedule, Enercept’s project coordinator will contact you and will regularly update you on the
status and projected schedule.

Complete the builder acknowledgment form and return to Enercept. This is required prior to shipment.

An invoice will be generated and sent to you.

The panels will be produced and a shipment date scheduled.
6) FOLLOW UP:

The project coordinator will call you following the delivery of your panels to answer any questions or assist with any concerns.

Warranty registration and customer survey (to evaluate our product and performance) will be sent at a later date.
On line: www.enercept.com Phone: 605-882-2222
Page 14
Fax: 605-882-2753 Email: [email protected]
E n e r c e p t S I P S a r e v e r s at i l e
T h e
B e t t e r
W a y
t o
B u i l d !
The Builders’ Choice
“I have never completed a project which was afforded so
many innovative ideas. It was all possible with Enercept
panels and their helpful staff. When I point out that the
Allegiance Building uses 35% of the energy of most
buildings its size, people are stunned.”
Paul Sorum, Architect, Sorum Design-Build, Fargo, ND
Allegiance Software Building, Fargo, ND
SIPA Building Excellence
Award Winner 2016
Blue Wave on the Bay
Ashland, WI
International Science Station
South Pole
Redlin Art Center, Watertown, SD
SIPA Building Excellence Award
Winner 2014
Brazos Valley Pediatric Dentistry,
College Station, TX
Building better SIPS for MORE THAN 30 years!
Specializing in SIPs for agricultural,
commercial, industrial and residential
applications, Enercept features panel
widths up to 8-feet and lengths up to
24-feet. SIPs are ideal for conventional
SIPs construction, Timber Frames, Log
Homes, or Steel Frame construction.
Enercept SIPs can be custom made for
specific applications or produced as solid
blank panels for on-site fabrication.
Call today for your free estimate!
Enercept, Inc.
Phone: 605-882-2222
3100 9th Avenue SE
Fax: 605-882-2753
Watertown, SD 57201
[email protected]
Proud member of these
fine organizations:
www.enercept.com
©2016