SE 607 - Galvin Engineering

Transcription

SE 607 - Galvin Engineering
SE - 607
Installation, Maintenance and Operating Instructions
DESCRIPTION
Floor mounted EMERGENCY DELUGE SHOWER and AERATED EYE/FACE WASH combination
unit. Shower is supplied with a 25mm stay open full flow ball valve, activated by a triangle pull rod.
Eye/Face wash is supplied with a 15mm stay open full flow ball valve,activated by a activation
paddle handle or foot pedal.
SPECIFICATIONS
SHOWER
EYE WASH
SHOWER HEAD - 200mm ABS Cycolac
VALVE
- 25mm Stainless Steel
ACTIVATOR
- 304 Stainless Steel Tube
INSTALLATION
EYE/FACE WASH
VALVE
ACTIVATOR
STANCHION
BASE PLATE
FOOT PEDAL ASSEM
-
Aerated, ABS Cycolac S/S Inserts
12mm Stainless Steel
304 Stainless Steel Paddle Handle
304 Stainless Steel Tube
304 Stainless Steel
304 Stainless Steel Tube
After unpacking carton, ensure all components are present. Mark out the floor and mount the bottom
stanchion section using suitable anchors (10-12mm x 50 Dynabolt). Then assemble top section (use
pipe sealant on all joints). Assemble pull rod and shower head, attach paddle handle and foot pedal.
Once the unit is completely assembled connect water supply to 25mm top inlet nipple. Failure to use
potable water can result in emergency units producing impure or contaminated water causing
possible further injury.Test unit.
NOTE : This unit should be connected to an uninterrupted source of potable water, no less than
25mm (1"), with a minimum flowing pressure of 130KPa and a maximum static pressure of 860 KPa.
OPERATION
OFF
The eye wash is activated by pushing the paddle
handle rearward. The unit will operate until the
paddle handle is manually pulled to the off position.
1733
OFF Position
ON Position
2134
150mm
Base Plate
Details
1650
Ø 12mm
4 places
150mm
1090
25mm
25mm
150
FLOW DATA
EYE-WASH
MAINTENANCE SCHEDULE
FLOW PRESSURE (KPa) : 136
FLOW RATE (LPM) :
36
WEEKLY
- Activate eyewash unit using push handle
- Allow water to flow for 30 seconds to
flush line.
- Ensure water flows evenly from both
outlets.
- Ensure water is clean.
YEARLY
- Ensure unit complies with
AS 4775-2007.
SHOWER
FLOW PRESSURE (KPa) : 34
FLOW RATE (LPM) :
76
69
76
103 138 172
76 76 76
R
SAFETY PRODUCTS
Combination Deluge Shower & Eye/Face Wash
ON
SPEAKMAN
SE 607
The shower is activated by pulling the triangle pull rod. Once the valve is activated the head will
continue to discharge water until the valve is manually closed, this is done by pushing the pull rod to
the off position.
ISO 9002
Lic QEC13179
FREE CALL 1 800 444 022
www.pbasafety.com.au
SE 607 SPARE PARTS LISTING
1
12
Aerator Screen Assembly
8
Part No - G05 0384
2
Aerator Screen Assembly & Cap
Part No - 05 1177 PC
3
6
Shroud Maintenance Kit
Part No - G10 0041
13
4
PULL
SPEAKMAN
-ON
EMERGENC
Y SHOW
ERS
Complete Shroud Assembly
Part No - G10 0042
7
17
Sold individually as
Volume Control Repair Kit
SPEAKMAN
R
Part No - G21 0082 PCP
14
15
No.
DESCRIPTION
PART No.
1
Aerator Sreen Assembly
2
Aerator Screen Assembly & Cap
05 1177 PC
3
Shroud Assembly Repair Kit (1 side)
G10 0041
4
Shroud Body & Aerator Assy. (1 side )
G10 0042
5
12mm Activation Ball Valve & Push Handle SE 910V
6
G05 0384
200mm Cycolac Shower Head
SE 870
7
Combination Frame
SE FRAME
8
25mm Acitvation Ball Valve & Lever
SE 911
9
Foot Pedal Connect Rod
SA 03003
10
Foot Pedal Activator Assembly
SE TREADLE
11
Inline Filter Assembly
G21 0082 PC P
12
Shower Arm 25mm BSP
SC 02001
13
Pull Rod Assembly
G47 0043 026
14
Stainless Steel Bowl
68 0033
15
Strainer Gauze
G21 0080
16
Manifold Assembly
G63 0049 MO
17
Volume Control Repair Kit
RPG05 0816
WARNING : Use only genuine Speakman parts when replacing or repairing
components. When ordering quote correct part numbers listed below.
To order free call 1 800 444 022 or free fax 1 800 444 024
11
10
9
SE 607
5
4
Supply Line Strainer Assembly
11
Combination Deluge Shower & Eye/Face Wash
SAFETY PRODUCTS
ISO 9002
Lic QEC13179
FREE CALL 1 800 444 022
www.pbasafety.com.au