SPRINT 16 Jr. / 16 / 20 / 25 TC

CM
YK
CNC
Turning Centres
SPRINT
16 Jr. / 16 / 20 / 25 TC
CM
YK
CM
YK
CM
YK
CM
YK
PARAMETERS
STANDARD SCOPE
•
•
•
•
•
•
•
•
•
•
•
•
•
CM
YK
•
3 Jaw Hydraulically Operated Chuck
with Power Pack
Hardened and Ground Pre-loaded
Ball Screws for axes
Linear Motion Guideways
Coolant Equipment
AC for Electrical Control Cabinet
Foot Switch for Chuck and Tailstock
Quill
Chip Tray
Boring Bar Holders
Set of Reduction Sleeves
Hydraulically Operated Tailstock Quill
Work Light
Beacon status Lamp
Centralized Programmable Lubrication
Unit
Fully Enclosed Guarding
•
•
•
•
•
•
•
•
•
•
•
•
25 TC
mm
mm
mm
mm
300
130
320
130
400
250
380
225
500
300
575
275
600
480
750
460
mm
250
300
400**
600***
mm
270
325
495
700
MAIN SPINDLE
Spindle nose
Bore through spindle
Max bar capacity
Standard chuck size
Chuck size (Optional)
mm
mm
mm
mm
A2 - 4
38
25*
135
–
A2 - 5
40
28*
165
200
A2 - 6
56
42*
200
250
A2-8
90
65 / 75*
250
305
SPINDLE DRIVE
AC motor rated power
(Continuous 30 min. Rating)
Speed range
Full power range
Kw
rpm
rpm
3.7 / 5.0
150 - 4000
1350 - 4000
5.5 / 7.5
50 - 5000
1050 / 2350
7.5 / 11
30 - 4000
1050 - 2350
11 / 15
35 - 3000
750 - 2000
SLIDES
Z-axis stroke
X-axis stroke
Feed
Rapid traverse (x / z)
Slant angle
mm
mm
mm / min
m / min
deg
270
100
0 - 5000
15 / 15
45
325
125
0 - 5000
30 / 30
45
495
150
0 - 5000
20 / 20
45
710
260
0 - 10000
20 / 20
45
mm
mm
kgf
mm
40
50
175
175
MT2
50
75
300
225
MT4
75
100
450
405
MT4
100
80
540
650
MT5
mm
mm
8
25
16 x 16
8
40
25 x 25
8
40
25 x 25
8
50
25 x 25
mm
mm
+ / - 0.005
+ / - 0.005
+ / - 0.005
+ / - 0.0075
+ / - 0.005
+ / - 0.0075
+ / - 0.005
+ / - 0.0075
mm
mm
+ / - 0.005
+ / - 0.005
+ / - 0.002
+ / - 0.003
+ / - 0.002
+ / - 0.003
+ / - 0.002
+ / - 0.003
kg
mm
mm
kva
2500
4000
2155 x 1110
2730 x 1600
2950 x 2050
2750 x 2725
10
15
3 Phase 415 V, 50 Hz
5000
2775 x 1720
2850 x 2835
20
6500
3500 x 1800
3710 x 3350
25
TURRET
No.of stations
Max boring bar
Tool cross section
Voltage Stabilizer
Ultra Isolation Transformer
Chip Conveyor with Bin
Bar Feeder
Axial Tool Holder
Revolving Centre
Collet Chuck
Steady Rest
Motorized Arm for Tool Offset
Turret Mounted Probe for Work Offset
Coolant through Tool
Siemens 828D
20 TC
CAPACITY
Swing over Bed
Swing over carriage
Distance between centers
Maximum turning diameter
Maximum turning length
with chuck
Maximum turning length
between center
TAIL STOCK
Quill diameter
Quill stroke
Max thrust
Tailstock base travel
Taper in tailstock quill
OPTIONS
SPRINT 16 TC Jr. 16 TC
ACCURACIES
Positioning
X-axis
Z-axis
Repeatibility
X-axis
Z-axis
INSTALLATION DATA
Weight
Foot print (approx.)
Floor Space (approx.)
Total connected load
Power supply
* When hollow chuck with hollow cylinder is used ** Turning Length 625 / 1000 mm available on request.
*** Turning length 1000 mm / 1500 mm / 2000 mm available on request
– Machine with C axis and live tool turret can be offered on request for Sprint 20 TC & 25 TC.
CONTROLLER
Specifications and design are subject to changes without prior notice.
Offices
Machine Tool Group
Again and a…gain
Batliboi Ltd.
Surat Navsari Road, Udhna - 394 220, Surat
Tel : +91 (261) 289 0551, 289 0435
Fax : + 91 (261) 289 0832
E-mail : [email protected]
Website : www.batliboi.com
• Mumbai : +91 91677 78553 • Surat : +91 98795 91665
• Ahmedabad : +91 99789 14811 • Pune : +91 99230 09898
• Kolhapur : 9673793535 • Bangalore : +91 99865 06601
• Chennai : +91 99627 22235 • Trichy : +91 95855 24700
• Hyderabad : +91 97034 45070 • Coimbatore : +91 98430 88216
• Ludhiana : +91 99881 97384 • Kolkata : +91 98301 08444
• Faridabad : +91 98739 38014, 98739 38038, 99990 96042, 99110 48813, 98739 38907
CM
YK
Graphic Communication Concepts / Point-n-Pixel / Urmegh Printers - Feb-2015 - 1 K
Major Specifications of CNC Turning Centres
CM
YK