russ wernimont designs

Transcription

THE DRAG SPECIALTIES
OCTOBER 2014
RUSS WERNIMONT DESIGNS
With a background in race car design and fabrication, Russ Wernimont rolled
onto the motorcycle scene in ‘92 with motorcycle fenders started through
Don Vesco. In this Skinny we are proud to present a couple
of the latest fender offerings from RWD. They add to what is
perhaps the widest selection of high-quality and uniquely
styled fenders you will find in the FatBook. They’ve been there since day
one, and we will continue to bring on more from this leading name.
1401-0470
CUSTOM DRESSER FRONT FENDERS
• One-piece 14-gauge stamped steel construction
1401-0471
• Fenders are individually inspected for straightness and consistency
• Very little body work necessary, easy to paint
• Spacers will be required; see below for specific requirements
• Made in the U.S.A.
NOTE: Length given is the contour length.
NOTE: All measurements are approximate.
PART #
DESCRIPTION
SUG. RETAIL
FOR 94-14 FLHT/FLHR/FLHX/FLTR MODELS
$
429.95
1401-04701 61/2" W for 30" front wheel; 55" long (LS-2 style)
FOR 14 FLHX/FLHXS MODELS
254.95
1401-04712 6" W for 19" front wheel; 42" long (LS-2 style)
FOR 94-14 FLHT/FLHR/FLHX/FLTR MODELS W/ 120/70-21 WHEEL/TIRE
249.95
1401-0469 3 51/2" W for 21" front wheel; 43" long (LS-2 style)
3/4" spacers required for 94-13 models; 3 ⁄ 8" spacers required for 14 models.
5⁄ 8" spacers required for 14 models.
3
11/2" spacers required for 94-13 models; 7⁄ 8" spacers required for 14 models.
1
2
RAYZER 2-INTO-1
EXHAUST SYSTEMS
• Wicked 2-into-1 performance with serpentine headpipes
• Work with stock or extended saddlebags
• 13/4" headpipes flow into a huge 4" (at outlet), radical
turnout megaphone with a contrast machined billet end cap
• Feature flat plane 12mm/18mm oxygen sensor ports
for wideband tuning capabilities
• Full-coverage 21⁄ 8" header heat shields
• 2" fiberglass-wrapped perforated baffle
1800-1664
• Stainless, laser-cut, Python branded muffler bands
• Available in chrome or matte black
PART #
DESCRIPTION
SUG. RETAIL
FOR 07-14 FLT, FLHX, FLTR, FLHR (EXCEPT H-D FL TRIKE MODELS)
$
899.95
1800-1664
Chrome
1800-1665
Matte black
999.95
1800-1665
DISCLAIMER: THE CALIFORNIA AIR RESOURCES BOARD (“CARB”) DOES NOT PERMIT THE USE OF AFTERMARKET EMISSION-RELATED PART(S) THAT ALTER THE PERFORMANCE OF OEM EMISSIONRELATED DEVICES UNLESS CARB HAS ISSUED AN EXECUTIVE ORDER, OTHER THAN ON RACING VEHICLES ON CLOSED COURSES. CHECK YOUR LOCAL LAWS AND MANUFACTURER’S INFORMATION.
dragspecialties.com
OCTOBER 2014
SUSPENSION CONTROLLER KIT
• Kit includes compressor, control panel and all
required plug-and-play wiring
• Provides instant suspension adjustment at
your fingertips
• Ensures safety, comfort and performance
• Completely bolt-on – no welding or drilling needed
PART #
1304-0585
DESCRIPTION
For 14 FLHTCUTG
SUG. RETAIL
$
599.95
STANDARD LENGTH FRONT
STAINLESS STEEL BRAKE LINE KITS
• Features clear-coated
stainless steel or black
vinyl-coated braided lines
with chrome steel fittings
• Meets DOT requirements
1741-3987
1741-3974
CLEAR-COATED STAINLESS STEEL
BLACK VINYL-COATED STAINLESS STEEL
PART #
OEM #
LENGTH
FOR 14 FLHT/FLHR/FLHX W/ ABS (UPPER)
1741-3987
41800011
641/2"
FOR 14 FLHT/FLHR/FLHX W/O ABS
1741-3973
41800174
171/4", 211/2", 281/4"
SUG. RETAIL
$
66.95
93.95
PART #
OEM #
LENGTH
1741-3988
41800011
641/2"
1741-3974
41800174
171/4", 211/2", 281/4"
SUG. RETAIL
$
70.95
100.95
EXTENDED LENGTH FRONT
STAINLESS STEEL BRAKE LINE KITS
• Features clear-coated
stainless steel or black vinylcoated braided extended lines
with chrome steel fittings
• Meets DOT requirements
CLEAR-COATED STAINLESS STEEL
PART #
EXTENDED LENGTH
OVERALL LENGTH
1741-3989
+2"
661/2"
1741-3990
+4"
681/2"
1741-3991
+6"
701/2"
1741-3992
+8"
721/2"
1741-3993
+10"
741/2"
1741-3994
+12"
761/2"
1741-3975
+2"
171/4", 211/2", 301/4"
1741-3977
+4"
171/4", 211/2", 321/4"
1741-3979
+6"
171/4", 211/2", 341/4"
1741-3981
+8"
171/4", 211/2", 361/4"
1741-3983
+10"
171/4", 211/2", 381/4"
1741-3985
+12"
171/4", 211/2", 401/4"
2
1741-3983
1741-3995
BLACK VINYL-COATED STAINLESS STEEL
SUG. RETAIL
$
66.95
66.95
66.95
69.95
69.95
69.95
93.95
93.95
93.95
95.95
97.95
97.95
PART #
EXTENDED LENGTH
OVERALL LENGTH
1741-3995
+2"
661/2"
1741-3996
+4"
681/2"
1741-3997
+6"
701/2"
1741-3998
+8"
721/2"
1741-3999
+10"
741/2"
1741-4000
+12"
761/2"
1741-3976
+2"
171/4", 211/2", 301/4"
1741-3978
+4"
171/4", 211/2", 321/4"
1741-3980
+6"
171/4", 211/2", 341/4"
1741-3982
+8"
171/4", 211/2", 361/4"
1741-3984
+10"
171/4", 211/2", 381/4"
1741-3986
+12"
171/4", 211/2", 401/4"
SUG. RETAIL
$
70.95
70.95
70.95
74.95
74.95
74.95
100.95
100.95
100.95
102.95
102.95
103.95
DRAG SPECIALTIES We could not be more pleased with the success of
our Extended Length OEM-Style Saddlebags. However, we have had a number of requests
for bags without exhaust cutouts. Always ones to listen to you and your customers, we have
come up with a solution we know will please all. Take a look at our new Saddlebag Block-Off
Panels shown below. Saddlebag owners can choose to
block-off one, or both, sides to complement any custom
exhaust selection. In stock and ready to ship today!
SADDLEBAG BLOCK-OFF PANELS
• Designed specifically for Drag
Specialties extended saddlebags,
PART #s 3501-0832 and 3501-0833,
when adding a custom exhaust
system or mufflers
• Precision formed to match the
exhaust cutouts in the saddlebags
PART #
3501-0938
• Manufactured from the same material as the
Drag Specialties saddlebags
3501-0938
3501-0965
• Must be professionally bonded to saddlebags
and requires some bodywork before painting
• Available for right- or left-side applications
• Sold each
DESCRIPTION
Left block-off panel
SUG. RETAIL
$
69.95
PART #
3501-0965
DESCRIPTION
Right block-off panel
SUG. RETAIL
$
69.95
PRECISION TOURBOX
• Direct bolt-on replacement
for the OEM tourbox
• Great for repair jobs or as an
additional accessory to give
your bike a new look
• Manufactured from OEM-grade
materials with precision tooling
• Mounting holes for brackets, latches, hinges,
reinforcing plate, side trim and side are pre-drilled
PRECISION
TOURBOX LID
• Mounting holes for corner lights,
grommets and speaker pods are
clearly marked (drilling is required)
• Direct bolt-on replacement
for the OEM tourbox lid
• Rear portion of the tourbox also has cut-outs
marked for installation of corner lights and housing
(cutting/sawing required)
• Manufactured from OEM-grade materials with precision tooling
• Mounting holes for brackets, latches, hinges and lock are predrilled
• Accepts OEM and aftermarket mounting hardware,
reinforcing plate, liner and accessories
• Smooth finish requires minimal prep before painting
• Includes detailed instructions
• Matching tourbox lid is available separately
PART #
3516-0180
• Mounting holes for tourbox backrest are clearly marked (drilling is required)
NOTE: Will fit 97-05
models if early mounting
plate is used as well as
late-style side lights/trim.
DESCRIPTION
For 06-13 FLHTC/FLHTCU/FLHTK/FLTRU;
replaces OEM #s 53121-09, 53128-09, 53145-09
SUG. RETAIL
$
299.95
SATIN BLACK
PUSHROD TUBE KITS
• Includes detailed instructions
PART #
3516-0179
DESCRIPTION
SUG. RETAIL
For 06-13 FLHTC/FLHTCU/FLHTK/FLTRU;
$
199.95
replaces OEM #s 79042-06, 79170-10
PRIMARY CHAIN
INSPECTION COVERS
• Machined from steel
• Compatible with adjustable pushrods
• Now available with a black
wrinkle or flat black finish
• One kit will do a complete engine
DESCRIPTION
For 99-14 Twin Cam
For 84-99 Evolution Big Twins
For L79-84 Shovelhead
For 66-E79 Shovelhead
For 04-14 XL
• Smooth finish requires minimal prep before painting
1107-0375
• Kits include upper and lower tubes,
clips, cups, springs and washers
PART #
0928-0043
0928-0044
0928-0045
0928-0046
0928-0042
• Accepts OEM and aftermarket mounting hardware, gasket and accessories
SUG. RETAIL
$
87.95
87.95
87.95
87.95
89.95
• Sold each
1107-0376
PART #
DESCRIPTION
SUG. RETAIL
FOR 70-84 FLH, 80-06 FXST/FLST/FXWG, 93-05 FXDWG;
REPL. OEM #60572-78
$
11.95
1107-0375
Wrinkle black
1107-0376
Flat black
11.95
3
OCTOBER 2014
3501-1005
4" EXTENDED SADDLEBAGS
• Constructed of fiberglass with a gel-coat finish
• Available with or without exhaust cutouts
• Accept OEM lids and hardware (sold separately)
• Right and left sides sold separately
3501-1004
3501-1005
3501-1004
FOR 14 FLHT/FLHR/FLHX MODELS
PART #
W/ CUTOUTS
3501-1004
3501-1005
DESCRIPTION
Left side
Right side
SUG. RETAIL
$
399.95
399.95
PART #
W/O CUTOUTS
3501-1006
3501-1007
DESCRIPTION
SUG. RETAIL
Left side
Right side
$
399.95
399.95
Stainless
EXTENDED
CONTROL
CABLE KITS
BRAIDED STAINLESS
STEEL CABLE/LINE KITS
Black
• Complete cable/line installation kits for
13" and 15" Burly Ape hangers
• Complete extended
cable/line kits for
13" and 15" Ape hangers
• Kits include extended brake lines,
clutch cable and all necessary wiring
• Include extended brake line,
clutch line and wiring
• Non-ABS kits include all front brake lines
• ABS kits include upper front line from master to ABS control unit
BLACK VINYL-COATED
PART #
DESCRIPTION
14 FLHX, FLHT/C/U W/O ABS
0610-0814
For 13" Ape hanger bar
0610-0816
14 FLHX, FLHT/C/U W/ABS
0610-0815
0610-0817
SUG. RETAIL
$
PART #
DESCRIPTION
08-13 FLHX/FLHT/C/U W/ABS
0610-0810
For 13" Ape hanger bars
0610-0812
08-13 FLHX/FLHT/C/U W/O ABS
0610-0811
0610-0813
349.95
349.95
13" STILETTO SHOCKS
289.95
289.95
• Main spring coils control the big hits and controls bottoming
SUG. RETAIL
$
419.95
419.95
419.95
419.95
• High performance dampers wrapped in a spring
combination designed to deal with subtle road imperfections
• Result is a plush ride that’s not afraid to play rough
STAINLESS STEEL
PART #
DESCRIPTION
14 FLHX, FLHT/C/U W/O ABS
0610-0818
0610-0820
14 FLHX, FLHT/C/U W/ABS
0610-0819
0610-0821
4
• Sold in pairs
SUG. RETAIL
$
419.90
419.90
319.95
319.95
NOTE: Before purchasing or attempting to install shocks
that are different from the OEM length, confirm that your wheel
travel can be altered without causing clearance issues, such as swingarm/
axle to exhaust contact as well as chain/belt guard or tire contact.
PART #
1310-0971
DESCRIPTION
For 86-14 XL models
SUG. RETAIL
$
299.95
ROLAND SANDS DESIGN continues to develop
exciting new products that combine quality, performance and style. Take a look
at some of his latest offerings to help turn late-model Sporties into custom
Café Racers - much like what you will find Roland himself burning up the
streets with every day. Roland chose Mustang Seats to produce seats worthy
of the RSD name with comfort, style and a perfect
fit designed to match his XL Tail Section. Perfect
choices to go with all other RSD XL products.
0804-0552
CAFE XL
TAIL SECTION
• Fiberglass construction with
stainless steel mounting brackets
• Covered with black gel coat
0804-0553
• Has clearance for stock shocks, wheels and tires
• Requires removal of stock fender, supporting struts and seat
• Requires relocation of taillight and turn signals
• Includes mounting hardware
SOLO SEATS FOR RSD CAFE TAIL SECTION
• Acccept solo seats PART #s 0804-0552 and 0804-0553; sold separately
• Seat baseplate is marine-grade fiberglass
PART #
0520-1355
DESCRIPTION
04-13 XL models
SUG. RETAIL
$
449.95
• Controlled density polyurethane foam construction
• Black distressed vinyl cover
• RSD metal logo
• Direct bolt-on seat for use with RDS Cafe Tail Section (PART #0520-1355)
3501-1003
• Completes the RSD Cafe Sportster package of products
• Ergonomic shape keeps the rider seated comfortably and firmly
PART #
0804-0552
0804-0553
DESCRIPTION
Boss
Plain
SUG. RETAIL
$
249.95
189.95
3501-1000
SWINGARM BAGS
• Full-grain Brazilian leather construction
• Quick-release buckle closure with magnetic reinforcement
• Installs with speedstrap hook-and-loop cable ties
3501-0990
3501-0989
• Mounts on left-hand side of the bike
• Dimensions: 10.5" L × 4.5" W × 11.5" H
SADDLEBAG HINGE COVERS
• Sold each
• CNC-machined from billet aluminum
• Replace the stock faceplates on touring models
equipped with hard bags
NOTE: Not for use with passenger floorboards or passenger footpegs.
PART #
FOR 84-14 FLST/FXST
3501-1000
3501-1001
FOR 86-14 XL
3501-1002
3501-1003
DESCRIPTION
Black w/ chrome buckle
Black w/ matte black buckle
Black w/ chrome buckle
Black w/ matte black buckle
SUG. RETAIL
$
149.95
149.95
149.95
149.95
• Retain all stock hinge functions
• Sold in pairs
PART #
FOR 14 FLHT/FLHR/FLHX
3501-0989
3501-0990
DESCRIPTION
Dimpled black
Dimpled chrome
SUG. RETAIL
$
289.95
289.95
5
OCTOBER 2014
AMP/FRONT SPEAKER KIT
• Includes front speakers and 200-watt, 2-channel amplifier
• Kit comes with everything required to complete installation
• 100% plug-n-play harness included
• Sold each
NOTE: Not compatible with CVO models with
factory amplifiers installed.
PART #
4405-0342
DESCRIPTION
For 98-13 FLHT/FLHX models
SUG. RETAIL
$
399.95
LED TURN SIGNAL INSERTS
LED HEADLIGHT BULB
• Upgrade conventional 1157 bulb-style turn
signals to LED-style
• Brighter and whiter than
halogen bulbs
• Plug-and-play design
• Low/high beam,
25W low/50W high
• Wide viewing angle
• Available in white dual-function design
• BCM-compliant
NOTE: A load equalizer
may be needed.
• Sold in pairs
NOTE: Not DOT certified.
PART #
2060-0428
2060-0429
DESCRIPTION
For bullet/deuce-style turn signals
For flat/FL-style turn signals
SUG. RETAIL
$
69.95
69.95
• 12-24 volts, 1,800 lumens,
6,000° Kelvin color temperature
• Kit includes bulb, fan, driver and
three-prong connector
• Fits most H4 lamps with P43t
flange base and standard three-prong 9003 connector
• Easy installation
NOTE: Will also fit Softail models using Headwinds 53/4" or 7" Bullet or
Rocket headlight housings.
2060-0428
PART #
2060-0430
DESCRIPTION
For 94-13 FLHT/FLHR/FLHX/FLTR
SUG. RETAIL
$
99.95
H13 NIGHT TECH BULB
• Feature advancements in performance,
durability and manufacturing
• 3600 Kelvin for whiter light than standard halogen bulbs
• Maintains DOT/SAE certification
• Bulb stays cool, resulting in longer life
2060-0429
• 65/55W power consumption; 85/75W light output
PART #
2060-0431
6
DESCRIPTION
H13 Night Tech bulb
SUG. RETAIL
$
34.95
LOWBROW CUSTOMS
One of the more recent additions to our Drag
Specialties family, these guys are on-board
with their own unique approach to the latest
trends in riding and riders. For this month’s
Skinny we have chosen a couple of their more
popular new offerings to be sure you are
ready when your
customers come
asking for them.
CUSTOM TOP
MOTOR MOUNTS
0933-0099
• These heavy-duty, custom top
motor mounts from Gasbox feature
a convenient spot to relocate your ignition switch and
the option of a CV carburetor choke mounting slot
0933-0100
PART #
DESCRIPTION
FOR 84-99 FXST/FLST MODELS
0933-0099
W/ ignition switch mount
W/ ignition switch mount and
0933-0100
CV carburetor choke mount
SUG. RETAIL
$
99.95
99.95
BIG TWIN MOTOR STAND
• The heavy-gauge steel construction
and durable black powdercoat
39MM TAPERED
FORK LEGS
• Perfect for cradling your Knucklehead,
Panhead or Shovelhead motor
• Shaved and tapered for the
proper chopper aesthetic
PART #
3801-0258
• Precision CNC lathe-turned
6061 T-6 aluminum
DESCRIPTION
For 36-99 Big Twin motors (except Twin Cam)
• Accept 39mm Narrow
Glide internals
HAIRPIN SPRING MOUNTING KIT
• Legs have no provisions
for mounting brake
calipers or fender
• Kit includes bungs that can be welded on to your
frame at any angle, dependent on how much of
a kick-up your solo seat has in the rear
• Two lengths are available:
stock length which uses
stock fork tubes or 2"
under stock, allowing you
to have the same amount
0403-0111
of travel with slammed front ends
with 2" under tubes (2" under fork tubes sold separately)
• A set of compression washers and the chrome buttonhead
Allens hold the springs in place, while another set of washers
and the chrome nylock nuts attach your springs to your seat
0403-0112
• Available in your choice of gorgeous machined aluminum or black
electroplate finish
FOR 87-07 XL, 87-99 FXD, FXR W/ 39MM FRONT FORK
0502-0485
UNIVERSAL
MOUNTING TABS
SUG. RETAIL
$
474.95
474.95
474.95
474.95
0502-0486
0502-0487
0502-0488
DESCRIPTION
1.5" wide × 1.3125" tall, .3125" × .625" slot
1.5" wide × 1.25" tall, .3125" hole
1.75" wide × 1.15 tall, .625 × .3125 slot
1.5" wide × 1.1875" tall, .3125" hole
SUG. RETAIL
$
44.95
• Same idea as Lowbrow’s finger tab,
but with a different shape
0502-0518
• These tabs are 2" long ×
21/2" wide, flat to the bolt
center is 1.4"
• The supplied 5 ⁄ 16"-18 × 1"
chrome button-head Allen bolt
nestles right in and looks great
PART #
0502-0518
0502-0519
0502-0519
• Constructed from 1/4" steel and available
with your choice of brass or aluminum insert
• Sold each
DESCRIPTION
W/ brass insert
W/ stainless steel insert
• Great for making custom
riserless handlebars
• Tapped for 1/2"-20 fine thread or
1/2"-13 coarse thread bolts
• Sold in 4-packs
PART #
0502-0485
0502-0486
0502-0487
0502-0488
DESCRIPTION
Hairpin spring mounting kit w/ brass washers
SUG. RETAIL
$
18.95
18.95
THREADED HANDLEBAR RISER BUNGS
• Cold-rolled mild steel tabs
• CNC-laser cut
PART #
0820-0070
RUBBER MOUNT
TRIANGULAR TABS
• 3/4" stainless steel custom axle and nut included
PART #
DESCRIPTION
STOCK LENGTH
0403-0111
Machined aluminum finish
0403-0112
Black electroplated Finish
2" UNDER STOCK LENGTH
0403-0113
Machined aluminum finish
0403-0114
Black electroplated Finish
SUG. RETAIL
$
69.95
SUG. RETAIL
$
15.95
15.95
15.95
15.95
• 1" diameter at the base, these
bungs feature a chamfer to allow
for proper weld penetration
PART #
0502-0483
0502-0484
• Feature 304
stainless
steel construction
• Sold in pairs
• Made in
the U.S.A.
DESCRIPTION
W/ 1/2"-20 fine thread
W/ 1/2"-13 coarse thread
0502-0484
SUG. RETAIL
$
14.95
14.95
7
OCTOBER 2014
RUBBER MOUNT FINGER TAB
• Gives you a tough mount with the added
feature of a military-spec rubber grommet
0630-1484
0630-1485
• Constructed from 1 ⁄ 8" thick steel
• The supplied 5 ⁄ 16"-18 × 1" chrome buttonhead Allen bolt nestles right in and looks great
• 31/2" long by 11/4" wide, from the
flat to the bolt center is 2.9"
• Available with brass insert
• Sold each
PART #
0502-0517
DESCRIPTION
Finger tab w/ brass insert
SUG. RETAIL
$
18.95
0630-1486
FISH SCALE GRIPS
• Injection-molded
Krayton rubber
COLE FOSTER
SIGNATURE
SERIES GRIPS
• Available for 1"
diameter handlebars
• Sold in pairs
• Injection-molded Krayton rubber
NOTE: Throttle sleeve sold separately.
0630-1476
• Available in white
PART #
0630-1484
0630-1485
0630-1486
0630-1487
• Sold in pairs
• Come in an embossed Cole Foster tin box
NOTE: Throttle sleeve sold separately.
PART #
0630-1476
0630-1477
DESCRIPTION
For 1" dia. handlebars
For 7 ⁄ 8" dia. handlebars
SUG. RETAIL
$
24.95
24.95
DESCRIPTION
Black
Orange
White
Blue
SUG. RETAIL
$
18.95
18.95
18.95
18.95
0630-1487
ADJUSTABLE FRONT ENGINE BRACKET
• Replace stock front engine bracket with custom slotted
bracket with alignment lines
THROTTLE BODY GLOVE
• Allows the rider to dial in the engine to perfect alignment
• Slides the engine left or right using
the same alignment principals as
FXR or early FLT models
• Slips over the stock throttle
body and hides everything in
a neat, clean design
• Covers the exposed wiring and
connector for the throttle body
servo unit that gets exposed if
you use an aftermarket air cleaner
• Hash marks at 0.05" intervals
1015-0129
• Includes black anodized aluminum bracket, two
3 ⁄ 8 -16 × 21/4 hex bolts and two 3 ⁄ 8 -16 nyloc nuts
PART #
DESCRIPTION
FOR 91-14 DYNA GLIDE
Adjustable front engine bracket;
0933-0105
repl. OEM #s 47226-90A,
47226-93, 47226-99
• Forced Air style fits the Paul Yaffe
Force Air cleaner or H-D Heavy
Breather Air Cleaners
• Relieved style fits most aftermarket
air cleaners with round backing plate
• Includes all necessary
installation hardware
95.95
• Kit moves the floorboards outward 11/4"
• Provides greater comfort by moving the legs away
from the gas tank and engine heat
FOR 08-14 FLHT/FLHX/FLHR/FLTR MODELS
8
$
DRIVER FLOORBOARD
EXTENDER KIT
1015-0132
• Primer or black textured
finish available
PART #
FORCED AIR
1015-0129
1015-0130
RELIEVED
1015-0131
1015-0132
SUG. RETAIL
DESCRIPTION
Black textured
Primer
Black textured
Primer
• Works well with oversized primary covers
SUG. RETAIL
$
97.95
87.95
97.95
87.95
• Kit is easy to install using included hardware
• Billet aluminum with a black finish
• Compatible with fairing lowers
PART #
1621-0629
DESCRIPTION
For 14 HD FL Trike models
SUG. RETAIL
$
77.95
ARLEN NESS The name Arlen Ness has meant the best in
custom accessories for over 40 years. Today, son Cory (shown here) and
grandson Zach have joined efforts to help create and promote the best
motorcycle products available. Through their efforts at rallies, races and
shows along with their prominent advertising campaigns, there is likely no
other manufacturer’s name that is more asked for than “Ness.”
Now have a look at some of their latest
offerings all available right now.
4405-0360
FRONT
SPEAKER GRILLES
3501-0996
3501-0997
ANGLED SADDLEBAGS
3501-0996
• 6061 T-6 billet aluminum
construction with machined cutouts/
highlights for a clean, sculpted look
• Injection-molded ABS bags provide superior strength and rigidity
• Add real style to your inner fairing
• Angled-cut design gives the ultimate custom look and
provides maximum cornering clearance
• Sold in pairs
• Saddlebags are stretched 5" longer than stock to cover
the muffler front to back and give that stretched look
• Bags have cutouts for dual exhaust applications; block-off
plates available separately for single or shorty exhaust applications
3501-0999
• Accept OEM lids and hardware (sold separately)
• Right and left side bags and block-off plates sold separately
PART #
DESCRIPTION
FOR 93-13 FLT/FLHT/FLHR/FLTR/FLHX
3501-0996
Left side saddlebag
3501-0997
Right side saddlebag
3501-0998
Left side saddlebag block-off plate
3501-0999
Right side saddlebag block-off plate
SUG. RETAIL
$
399.95
399.95
39.95
39.95
4405-0364
4405-0365
PART #
DESCRIPTION
FOR 96-13 FLHT/FLHX AND H-D FL TRIKE
4405-0360
Slot Track, chrome
4405-0363
Slot Track, black
4405-0361
Deep Cut, chrome
4405-0364
Deep Cut, black
4405-0362
Beveled, chrome
4405-0365
Beveled, black
SUG. RETAIL
$
199.95
199.95
199.95
199.95
199.95
199.95
10-GAUGE
BILLET HORN KITS
• Forged billet aluminum
construction with a stainless
steel mesh screen
• High-performance 110dB
horn plugs into the factory wiring
BILLET DASH
INSERTS
• Custom/universal horn brackets
include a steel bracket
• Fit nicely into factory
dash covers
2107-0201
• FLT/FLHT/FLHR/FLHX/Dyna/Softail
kits include billet aluminum bracket that mounts in the stock location
• Made from billet aluminum
• Available in chrome
and black anodized
2107-0200
• Available in chrome or anodized black
2202-0180
2202-0200
PART #
DESCRIPTION
FOR 08-14 FLHX
2202-0180
Beveled, black
FOR 08-14 FLHT, FLHTC
2202-0200
Deep cut, chrome
2202-0202
Deep cut, black
FOR 89-07 FLHS, FLTR, FLT, FLHT, FLTC
2202-0201
Deep cut, chrome
2202-0203
Deep cut, black
2202-0203
SUG. RETAIL
$
99.95
129.95
129.95
129.95
129.95
PART #
DESCRIPTION
SUG. RETAIL
FOR 91-14 FLT/FLHT/FLHR/FLHX/DYNA/SOFTAIL (EXCEPT FXSB/SE)
$
199.95
2107-0202
Black
2107-0203
Chrome
199.95
FOR 91-14 XL
2107-0204
Black
199.95
2107-0205
Chrome
199.95
UNIVERSAL
2107-0200
Black
199.95
2107-0201
Chrome
199.95
9
OCTOBER 2014
SOLUTION LICENSE
PLATE BRACKETS
• Cold-forged 6061 T-6 aluminum bracket base
• Heat-treated, black electroplated steel
axle washers (2 provided)
0630-1480
0630-1481
0630-1482
RENEGADE 1" GRIPS
• Injection-molded Krayton
synthetic rubber
0630-1483
2030-0833
• 1/4" thick 6061 T-6 alloy plate secures with four countersunk Allen
screws to provide a customizable location for plate mounting
• Classic surface designs help absorb
shock and dampen vibration
• Polished raw alloy or matte black electroplated finishes available
• Sold in pairs; throttle sleeve not included
PART #
0630-1480
0630-1481
0630-1482
0630-1483
• Two different hat-shaped chromoly spacers:
one with a keyway to fit aftermarket chopper
frames and one flush mounted for stock axle
plates; fit inside the alloy bracket to provide
solid clamping power beneath the rear axle
DESCRIPTION
Black
Cream
Oxblood
Fluorescent green
SUG. RETAIL
$
17.95
17.95
17.95
17.95
PART #
2030-0833
2030-0834
DESCRIPTION
Polished
Matte black
SUG. RETAIL
$
109.95
109.95
1107-0408
DERBY
COVERS
• CNC-machined 6061
T-6 billet aluminum construction
• Available in satin silver anodized, matte
black electroplate or chrome plated finishes
• Mount with existing hardware
2030-0835
2030-0837
SOLUTION LICENSE PLATE
AND TAILLIGHT BRACKETS
• Cold-forged 6061 T-6 aluminum bracket base
• Identical to Biltwell’s Solution Side-Mount License Plate Bracket in terms of
function and construction, but upgraded to accept Biltwell’s Model B-E and
select aftermarket Model A style taillights
• Heat-treated, black electroplated steel axle washers (2 provided)
• Two different hat-shaped chromoly spacers; one with a keyway to fit aftermarket
chopper frames and one flush mounted for stock axle plates, fit inside the alloy
bracket to provide solid clamping power beneath the rear axle
• 1/4" thick 6061 T-6 alloy plate secures with four countersunk Allen screws to
provide a customizable location for plate mounting
• Polished raw alloy or matte black electroplated finishes available
PART #
HORIZONTAL MOUNT
2030-0835
2030-0836
VERTICAL MOUNT
2030-0837
2030-0838
10
DESCRIPTION
Polished
Matte black
Polished
Matte black
SUG. RETAIL
$
129.95
129.95
129.95
129.95
PART #
DESCRIPTION
FOR 99-14 BIG TWIN MODELS
1107-0411
Dished, silver
1107-0412
Dished, black
1107-0413
Dished, chrome
FOR 70-98 BIG TWIN MODELS
1107-0408
Dished, silver
1107-0409
Dished, black
1107-0410
Dished, chrome
FOR 04-14 XL MODELS
1107-0417
Dished, silver
1107-0418
Dished, black
1107-0419
Dished, chrome
1107-0429
Finned, silver
1107-0430
Finned, black
1107-0431
Finned, chrome
FOR 94-03 XL MODELS
1107-0414
Dished, silver
1107-0415
Dished, black
1107-0416
Dished, chrome
1107-0426
Finned, silver
1107-0427
Finned, black
1107-0428
Finned, chrome
1107-0430
SUG. RETAIL
$
99.95
99.95
99.95
99.95
99.95
99.95
99.95
99.95
99.95
99.95
99.95
99.95
99.95
99.95
99.95
99.95
99.95
99.95
CARL BROUHARD CROSS DESIGN SOLO SEAT
WITH DRIVER BACKREST OPTION
• Solar-reflective leather in the seating area and automotive-grade vinyl on the
sides; patented process reduces surface temperature by as much as 25°F for a
cooler seat, higher durability and longer life over conventional leather or vinyl
• Advanced clean look with optional EZ GLIDE II™ backrest capability
• Flexible urethane foam for maximum comfort
• 3 ⁄ 16" ABS thermoformed seat base with carpeted bottom
and rubber bumpers to protect paint
• Lower rider 11/2" from stock seat
• Include two polished stainless steel mounting nuts and
a leather fender bib for a cleaner installation
0822-0133
• Optional backrests feature solar-reflective leather cover and multiple detents
with virtually no metal-to-metal contact for vertical and fore/aft pad adjustment
0822-0157
• EZ Glide II™ small backrest (PART #0822-0133) measures 9" W × 51/4" H and
does not include a pouch; EZ Glide II™ large backrest (PART #0822-0154)
measures 10" W × 71/2" H and includes a pouch on the backside of the pad
• “The Convertible” EZ Glide II large backrest (PART #0822-0157) includes a rain
cover that pulls out of a pouch on the backside of the pad and covers the entire seat
• Optional rear pillion pads (PART #s 0801-0779, 0801-0779) are also available in
matching styles and two sizes
• Backrests and pillion pads sold separately
PART #
0801-0889
• Made in the U.S.A. by Drag Specialties® Seats
DESCRIPTION
Cross, black stitch for 08-14 FLHT, FLHR,
FLTR, FLHX (23" L × 123/4" W × 13/4" H)
SUG. RETAIL
$
379.95
CARL BROUHARD CROSS DESIGN LOW PROFILE
EZ ON SOLO SEAT WITH FORWARD POSITIONING
CARL BROUHARD CROSS DESIGN
LOW-PROFILE EZ ON SOLO FRONT SEAT
• Seat geometry moves rider forward 2” compared to standard Low-Profile Solo;
moves rider forward 1” compared to a stock Street Glide or Road Glide seat
• Solar-reflective leather in the seating area and automotive-grade vinyl on the
sides; patented process reduces surface temperature by as much as 25°F for a
cooler seat, higher durability and longer life over conventional leather or vinyl
• Solar-reflective leather in the seating area and automotive-grade
vinyl on the sides; patented process reduces surface temperature
by as much as 25°F for a cooler seat, higher durability and longer
life over conventional leather or vinyl
• 3 ⁄ 16" ABS thermoformed seat base with carpeted bottom
and rubber bumpers to protect paint
• New EZ Mount system requires no tools for taking seat on and off
• 3 ⁄ 16" ABS thermoformed seat base with carpeted bottom to protect paint
• Seat geometry places rider farther back and up to 11/2" lower than stock seat
• New EZ Mount system requires no tools for taking seat on and off
• Lower position creates better rider position with improved styling
• Lowers rider up to 11/2" lower than stock seat, depending on model
• Lower position creates better rider position with improved styling
• Seat covers the two seat fender studs for
a low, clean look
• Seat covers the two seat fender studs for a low, clean look
• Made in the U.S.A. by Drag Specialties Seats
®
PART #
0801-0888
DESCRIPTION
For 08-14 FLHT, FLHR, FLTR, FLHX
(23" L overall × 131/4" W × 13/4" H)
NOTE: Seats do not
accept pillion pads.
SUG. RETAIL
$
299.95
EZ Mount
System
• Made in the U.S.A. by Drag Specialties® Seats
NOTE: Seats do not accept pillion pads.
PART #
0801-0890
9901-1518
DESCRIPTION
Cross, black stitch for 08-14 FLHT, FLHR,
FLTR, FLHX (23" L overall × 131/4" W × 11/2" H)
SUG. RETAIL
$
299.95
11

russ wernimont designs

Transcription

Similar documents

Cottswood Interiors 8x7.7_00043894

Seven for All Mankind

La Centerra at Cinco Ranch

Retail Leasing Opportunity

PAUL YAFFE`S BAGGER NATION For

Rooms To Go Distribution Center

folleto window light - Multimedia Content Management

$83,300.00

Retail ConnectSM

the products included in the School and Teacher