Rock-ola Rocket - Miele Sales and Service

Rock-ola
Rocket
Disclaimer & Important Safety Information
TouchTunes and the TouchTunes logo are trademarks of TouchTunes Music Corporation. All other
brand and product names are trademarks or registered trademarks of their respective corporations. The mention
of any product does not constitute an endorsement by TouchTunes Music Corporation.This manual is furnished
under a lease agreement and may only be copied or used within accordance with the terms of such lease
agreement. The content of this manual is furnished for informational use only, is subject to change without
notice, and should not be construed as a commitment by TouchTunes Music Corporation. TouchTunes Music
Corporation assumes no responsibility or liability for any errors or inaccuracies that may appear in this
document.Except as permitted by such lease agreement, no part of this publication may be reproduced, stored in
any retrieval system, or transmitted, in any form or by any means, electronic, mechanical, recording, or
otherwise, without prior written consent of TouchTunes Music Corporation.Changes are periodically made to
the information herein; these changes will be incorporated into new editions of this publication. TouchTunes
may make improvements and/or changes in the products and/or software programs described in this publication
at any time.If you have comments on this manual or the products it describes, address them to:
TouchTunes Music Corporation
Attention: Publications
3 Commerce Place, 4th Floor
Montreal, Quebec, Canada H3E 1H7
Telephone: 1-888-338-JUKE
Support hotline: 1-888-711-JUKE
Fax: (847) 419-3304
TouchTunes may use or distribute whatever information you supply in any way it believes appropriate
without incurring any obligations to you.Copyright © 2007 TouchTunes Music Corporation. All rights reserved,
including those to reproduce this publication or parts thereof in any form without permission in writing from
TouchTunes Music Corporation.
TouchTunes Music Corporation is not responsible for any damage resulting from the improper
installation or connection of this conversion kit or any other external equipment to your jukebox. TouchTunes is
not responsible for any damage caused during shipment (except the shipment to the original purchaser) or any
damage caused by:
•
•
•
•
Impacts, fluids, fire, flood, wind, earthquake, lightning or similar disaster.
Unauthorized modifications, attachments or peripherals, improper use, environment, installation or
electrical supply.
Improper maintenance.
Any other misuse, abuse, or mishandling.
TouchTunes does not recommend installing any conversion kit on location.
Do not block any ventilation opening. Install in accordance with the manufacturer’s instructions— To
ensure reliable operation of the product and to protect it from overheating, put the product in a position and
location that will not interfere with its proper ventilation.
Do not let objects or liquids enter the product— as they may touch dangerous voltage points or short-out
parts that could result in a fire or electric shock.
WARNING: This symbol alerts you to the presence of “dangerous voltage” within the product enclosure
that may be of sufficient magnitude to constitute a risk of electrical shock. Do not remove the cover or back.
There are no user-serviceable parts inside. Servicing must be performed by qualified personnel only.
Welcome
Congratulations on your purchase of a TouchTunes Conversion Kit, an affordable and winning solution
for bringing you the patron-pleasing power of digital downloaded music!
Behind the scenes, you update the jukebox’s music content on line via TouchTunes’ web-based
Operator Dashboard from your office, home, or anywhere—or any computer equipped with an internet
connection—alleviating the time and expense that would otherwise be involved in making a service call to the
location.
About This Guide
This guide is intended for Operators of TouchTunes digital jukeboxes and their technicians,TouchTunes
technical support and field service personnel. It explains how to convert your jukebox into a TouchTunes
Digital Jukebox using the TouchTunes Conversion Kit.
Unpacking and Checking Conversion Kit Components
Before you install the conversion kit, you must ensure that you have received all hardware components
and that both hardware components and the items in the parts kit are in good condition. Operators have a 14
days period to report to TouchTunes any missing or damaged parts. After this 14 day periord any missing or
damaged parts will become the responsabilty of the operator. This poicy is noted on the shipping box that your
TochTunes Kit was delivered in.
Contacting Touch Tunes
Contacting TouchTunes Directly from the Operator Dashboard
You can use the Contacts page in the TouchTunes Dashboard to email many departments at
TouchTunes, including Technical Support. Using the Contacts page is the easiest way to contact TouchTunes
and also allows TouchTunes to respond to your question, problem or request very quickly. To access the
Contacts page, choose TouchTunesContacts and then follow the appropriate email link for the department you
want to contact.
Contacting TouchTunes by Phone
You can also get assistance by calling the TouchTunes Technical Support department toll-free at 1-888711-5853. If you are outside of the toll-free area, you can still contact the TouchTunes Technical Support
department by dialling 1-847-419-3300 and pressing 1 when prompted.
Note: Long-distance telephone charges may apply if you are calling from outside of the toll-free area.
Important Prerequisite
Your TouchTunes Conversion Kit has been designed and provided as an economical solution for
converting your previous jukebox into a full-fledged TouchTunes digital jukebox by integrating with many of
your currently installed components. As such, the successful installation of your conversion kit requires that
your current hardware be in good working condition.
Before proceeding with installation of this kit, it is imperative that you verify that all currently installed
electronic components are fully functional. You must also inspect the cabinet or enclosure to ensure that it has
not sustained damage that would inhibit or prevent the installation of any equipment provided with the kit—
either internally installed functional components, or externally applied aesthetic enhancements.
Note: Installing a TouchTunes Conversion Kit does not fix a broken jukebox!
Estimated Time to Complete the Installation
The degree of complexity and time to complete the conversion may vary slightly from model to model,
and may depend upon the installer’s experience and comfort level with working with electronic equipment and
power tools. TouchTunes’ installation team has determined that a typical installation can usually be completed
in 2 1/2 hours.
Workflow
The procedures described here, based on the experience of TouchTunes’ expert installation personnel,
represent a logical sequence of events and best practices for accomplishing your conversion within the least
time and with minimal difficulty. In general, the basic procedures are:
1. Removal of old components:
Removal creates space for the installation of the new equipment and allows for a clean, compact, and
clutter-free installation with easy access to all components. This section also describes the necessary
components to leave in the jukebox.
2. Installation of new components:
This procedure involves installation of all TouchTunes components in the jukebox enclosure, conversion
of the current amplifier, and modification of the door (as required).
3. Testing and activation of the converted jukebox:
This procedure allows you to verify the success of your installation.
NOTE: These procedures are described in detail in the following subsections.
Power supply
TouchTunes JCB layout
connection
J1
Connection
from squid
cable
Hard drive
This is the control panel of your JCB
Ethernet
Connection
The Power supply and JCB are mounted to a mounting board for ease of installation. The mounting board is
perforated so it can be separated to ease installations by mounting the power supply away from the JCB, due to
space constrictions in some kit models. (See Figure 1.0)
Figure 1.0
ID Box
ox (Make sure you connect ID Box before reinstallation)
Here are the connections on the squid cable
Squid cable line
Connected to
J1
J2
To JCB Input /Output
Light show circuit boards (also a 12 volt DC source) red = +12vdc / black
= ground
Connection to Coin A
Acceptor adapter harness/ Imonex-300364
300364-009
Connection to #1 Bill Acceptor
Connection to The ID Box
To LCD monitor power 12 volts DC
To External C
Counter
DB9 serial connection for touch screen
To #2 Bill A
Acceptor
To Switched 12 volts DC
J3
J4
J5
J6
J7
J8
J9
J10
Part No.
300310-001
300377-001
300270-001
Description
Rock-ola Rocket
Computer Assembly
JCB Power Supply
JCB Computer
ID Box Assembly
Quantity
1
1
1
Cable Pak
300362-120
300364-009
300299-050
300163-120
300142-036
C8
300180-072
Squid Main Harness
Imonex Harness
ID Box to RF Harness
VGA Cable
Cat 5 Cable
Cable Tie
AC Line Cord
1
1
1
1
1
6
1
Monitor
302273-001
400214-001
Monitor 19” LCD
Monitor Bezel
1
1
Graphic
650-011
Monitor Surround Graphic
1
Components
410-03S
FAN-3
KIT SPECIFIC
302-003
300268-001
100248-006
700039-001
102-017
300019-001
600024-001
PS-1
Stainless Button Cover
Fan Assembly
Instructions :Rocket
Non AC Switch Box
Antenna
External Counter
Digital Amp DA415
Digital Amp Mount
Cat5 Cable
Remote Control
Power strip /w AC plug
1
1
1
1
1
1
1
1
1
1
1
Monitor Hardware
F4
A7
C4
7/16” Truss Head Screws
Nylon Spacers
Metric m8 Screw
8
8
8
Hardware
A9
Wire Clamps
3
Kit Specific
400331-001
600101-001
Bill Acceptor: ICT 880
Credit Card Kit
410-012S
Stainless Button Cover w/ Credit
Card Slot
Only if Ordered
Only if Ordered
Only if ordered with
Credit Card Kit
Will ship instead of
part # 410-03S
Disassembly
WARNING: To prevent risk of electrical shock, do not attempt any of the procedures
described here without first disconnecting all electrical power to the jukebox.
NOTE:Keep any hardware, wiring, etc.. you remove during disassembly, as it may be reused to install certain
components of the Conversion Kit.
The following components will be used in conjunction with your TouchTunes Conversion Kit and will remain
in the jukebox after conversion.
•
•
•
•
•
•
Any Lights and Wiring
“Rock-ola Power Supply”
Speaker Crossover
Cable that connected the Speaker Crossover to the Rock-ola Amplifier
Coin Mechanism and Bracket
Speakers and SpeakerWiring
Please remove the following parts:
•
•
•
•
•
•
CD Changer
Title Page Unit
Amplifier and wooden ring around Amplifier
Keyboard and Buttons and Display
Bill Acceptor
Title Page Glass
Cleaning
It is very important to clean your jukebox. Proper airflow is crucial to the maintenance of your TouchTunes
Digital jukebox. Cleaning the inside of the cabinet, especially with alcohol, is important for proper adhesion of
certain hardware; as well as easy location and identification of new and old wires. Take time now to organize
and dress all remaining wires, using the cabinet’s existing wire loops. The kit will be easiest to clean before
installing any TouchTunes components. However, certain steps will allow you to reach different areas of the
cabinet and door, so be sure to clean as you go.
Assembly
ID Box and Antenna Assembly
Before attaching any components to your jukebox, test fit them to ensure that the appropriate connections can
then be made and other jukebox components (new and old) will allow proper clearance. When installing a JCB
squid cable, it is essential that you pre-fit the harness.
•
•
Remove the ID box from the mounting board.
Connect the ID box to the antenna extension cable.
ID Box and Antenna Assembly (conti.)
•
Connect the J5 from the Squid cable to the other side of the ID box. (See Figure 1.1)
1.
Figure 1.1
J5 from
Squid Cable
•
•
Antenna Cable
(300299-50)
50)
Reinstall the ID box.
Mount the RF module (antenna see picture 1.
1.2).
Figure 1.2
Antenna
RF module
•
•
Fasten the antenna to either the inside or outside rear of the cabinet. (Connecting
Connecting to the outside rear will
provide the best possible reception for the RF Remote.)
Connect the antenna using the extension cable from the ID box.
Converting the Main Enclosure
•
•
•
•
To reach the proper TouchTunes components, the speaker crossover must be moved from its original
location to a higher one.. (See Blue Arrow in Figure 1.3 on next page)
Using the provided amplifier mount as a template, mark the hole needed to make room for the
t DA415
Digital Amplifier.
• Butt the corner of the mount to the corner of the existing hole to make use of a common corner.
• Trace the
he inside edge to provide a guide to cut by.
• Using a jigsaw cut thee area you traced
traced.
With the hole cut, tack the amp mount in place with tape or a partially fastened screw.
Place the DA415 Digital Amplifier over the mount and, using six factory cabinet screws,
scr
fasten the
amplifier to the mount and cabinet wall at once. (See Red Arrow in Figure 1.3 on next page)
Converting the Main Enclosure (conti.)
•
•
•
Mount the provided power strip vertically next to the DA415 Digital Amplifier (See Green Arrow in
Figure 1.3)
Connect the power strip’s power cord to the “Service Outlet” port of the “Rock-ola Syber Sonic Power
Supply”.
Using the existing screws from the disassembly screw through the mounting board and mount theJCB
Computer Assembly to the back wall in line with the Amp Mounting Board. When mounting the JCB
computer into your cabinet you must allow 4” on the top for connections and 6” of clearance on the
bottom to allow room for the hard drive to be installed. (See Yellow Arrow Figure 1.3)
Figure 1.3
•
•
•
Connect the AC Power cord to the Amplifier and then to the power strip.
Plug AC line cord from the JCB Power supply to the power strip.
Mount the external counter to a convenient location and connect to J7 of the squid cable
Fan Assembly
•
•
•
•
•
•
•
•
•
•
Find a place to mount the fan where the fan cord will reach the power strip.
Locate the metal fan grill that was included in your kit.
Hold the metal fan grill against the back of the cabinet, trace the outer circle and mark the 4 screw hole
locations.
Using a jigsaw or hole-saw cut the 4” hole that you just traced and drill out the 4 marked holes.
Attach the fan guard with holes to the front of the fan using the 2 provided screws.
Hold the fan grill on the back side of the cabinet and start your 4 screw.
Place the fan on the inside of the cabinet over the 4” hole and continue screwing the fan tight to the
cabinet.
Attach the foam filter and other guard to the front of fan.
Locate your fan cord and attach the terminal ends.
Plug the fan cord into the fan and then into the power strip.
Monitor/Graphic Assembly
•
•
Install the new monitor surround graphic.
Reinstall the retainer brackets on the lid there are 3, the one on the bottom and the two sides. (See Figure
1.4 for bracket placement.)
Figure 1.4
Monitor/Graphic Assembly (conti.)
•
Attach the U-shaped bracket to the top and bottom of the monitor. (See Red Arrows in Figure 1.5)
Figure 1.5
• Set the monitor into the bezel and attach it by installing 8 screws around the perimeter of the bezel.
(See Yellow arrows in Figure 1.6)
Figure 1.6
•
Using the 8 nylon crush spacers and the 8 truss head screws provided mount the monitor bezel assembly
to the new monitor surround making sure the video, serial and power connections on the back portion of
the monitor are facing downward.
Stainless Button Cover
•
Carefully line up and install the stainless button cover over the spot where we removed the front keyboard.
NOTE: There is an optional Credit card kit and a stainless steel front with a credit card slot available at
www.TouchTunesKits.com
Wiring
DA415 Amplifier
•
Locate thecable that was connecting the Rock-ola amplifier. This cable has four leads: white, green,
red, and black. (See Figure 2.0)
Figure 2.0
•
•
•
Start by cutting off the white plug end on this wire.
Strip about an eighth of an inch of insulator from each lead.
Connect the leads to one of the Buchanan plugs provided with the DA415 Digital Amplifier. To
connect the leads to the Buchanan plug, unscrew the lug in each channel, insert the bare lead, and
retighten the lug. (See Figure 2.1.)
Figure 2.1
Left Channel
Right Channel
1+2
1 2
-4
+3
3 4
+- + -
Digital Amp
DA415 Amplifier (conti.)
•
Plug the Buchanan plug into the DA415 amplifier at the Zone A. (See Figure 2.2)
a. The second buchannon plug can be used to connect external speakers.
Figure 2.2
•
Install the 2 provided Cat 5 cables, 1 from Zone 1 of the JCB Computer to the A port on the amp and 1
from the Zone 2 of the JCB Computer to the B port of the amp.
Coin Acceptor
•
•
•
Connect the end of coin acceptor cable J3 to the end of the extension cable. The extention cable will
have two black leads. These are the ground wires and can be connected to the coin switches common
lug.
The white wire is your quarter lead and should be connected to the normally open lug of the coin mech
switch.
In this application the green wire is not used and should be terminated.
Bill Acceptor
If you didn’t order a bill acceptor with your kit be sure you are using a 24v MDB bill acceptor. The original bill
acceptor had a smaller bezel, thus the new bill acceptor won’t fit in the original hole.
•
•
•
Install the new bill acceptor by using longer mounting screws on the top mounting points.
Then butt the nose of the bezel to the sheet metal front and secure the fasteners. No cutting should be
required, and possibly only a few minor alterations.
Connect J4 of the squid cable to the bill acceptor.
Monitor:
•
•
•
•
Connect VGA cable to the monitor and from the monitor to the JCB computer.
Connect the the DB9 Serial cable J8 of the JCB harness to the monitor serial connection.
Plug the J6 Cable of the JCB harness to the 12V DC monitor-power outlet.
Route the cables up wards along the side of the monitor and secure them to the top of the lid and down
into the cabinet leaving some slack where the lid opens.
Switch Box:(See Figure 2.3)
•
•
•
Mount the switch box at a location where leads will reach pins 10-12 on the light show output plug on
the upper part of the Rock-ola power supply.
Connect the Blue and Yellow wires from the switch box to the plug on the Rock-ola power supply at
pins10-12.This will switch the lights on and off with the jukebox via the remote control. (See Figure 2.2
on next page) NOTE: Wire colors in picture are different than instructions as extra wire was used as an
extension to reach the plug.
Connect the white plug from the switch box to the J10connection of the squid cable harness
Figure 2.3
Testing and Activating Your New TouchTunes Jukebox
NOTE: To perform the steps in this procedure, you need a hard drive prepared with TouchTunes software, if
you haven’t already contacted TuneTunes to order this please do so. Hard drive is not shipped with conversion
kit and is under a serparate order form. To contact Touchtunes, see Contacting TouchTunes on page 3.
Power Up Your Jukebox
1.
2.
3.
4.
Plug in the main power.
Turn on the power strip.
Turn on power supply and JCB LED power indicators will illuminate.
Press the POWER button and the 12 Volt switched LED will illuminate.
Congratulations You have successfully assembled your TouchTunes Conversion kit!