century - Miller Industries

CENTURY
L E G E N D A R Y
®
L E A D E R S H I P
OWNER'S MANUAL
10 SERIES
ALUMINUM & STEEL
CARRIERS
INSTALLATION, OPERATION, MAINTENANCE & PARTS
NOTE: MANUAL including SPECIFICATIONS, subject to change without notice
All ratings specified are based on structural factors only,
not vehicle capacities or capabilities.
CENTURY®
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Phone (423) 238-4171 • FAX (423) 238-5371
FORM NO. 0500803
REV. A
02 / 01
PRICE $25.00
LIMITED WARRANTY
MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as
MILLER, warrants to the original purchaser that each new MILLER Carrier will be
free from defects in material and workmanship for a period of one (1) year from the
date of purchase. The purchaser must promptly notify MILLER in writing of any
failure in material or workmanship. In no event shall such notification be received
by MILLER later than thirteen (13) months from date of delivery.
The obligation under this warranty, statutory or otherwise, is limited to the repair or
replacement at our factory, or at a point designated by us, of such part or parts as
shall appear to us upon inspection to be defective in material or workmanship. New
or remanufactured parts will be used for any replacement.
This warranty does not obligate MILLER to bear the cost of labor or transportation
charges in connection with the replacement or repair of any parts found to be
defective, nor shall it apply to a product upon which repairs or alterations have
been made unless authorized by us.
MILLER shall in no event be liable for any incidental or consequential damages or
contingent arising out of the failure of any parts or products to operate properly. NO
IMPLIED, EXPRESS, OR STATUTORY WARRANTY OTHER THAN STATED
HEREIN IS MADE OR AUTHORIZED TO BE MADE BY OR FOR US, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
MILLER makes no warranty, express or implied, as to finished products
manufactured or supplied by another manufacturer or supplier by MILLER to
purchaser, including, but not limited to, any vehicle to which a MILLER product may
be affixed or accessories or wire rope (cable), and expressly disclaims any implied
warranties of merchantability or fitness for a particular purpose as to such equipment
or products. This language shall in no way affect or diminish the rights of purchaser
to rely on such warranties as are extended by such manufacturers or suppliers.
MILLER, whose policy is one of continuous improvement, reserves the right to
improve its product through changes in design or materials as it may deem desirable
without being obligated to incorporate such changes in products of prior manufacture.
IT IS EXPRESSLY UNDERSTOOD THAT THERE IS NO IMPLIED WARRANTY
THAT MILLER CARRIERS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR
MOVING PERSONS OR OTHER IMPROPER USE. THIS WARRANTY IS NOT
TRANSFERABLE.
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Telephone (423) 238-4171
SERIAL NUMBER
Section VI - PARTS
This Section is provided by the manufacturer for the purpose of ordering
any component part of the 10 Series Car Carrier that may be required
when part replacement is necessary. Be certain to use only original
equipment replacement parts for warranty purposes as well as for keeping
your 10 Series Car Carrier in its original state and optimum operating
capacities.
When ordering replacement or spare parts be sure to provide the following
information to the manufacturer’s Parts Department.
1.
2.
3.
4.
5.
6.
7.
Manual Number & Date of Publication
Manual Page Number
Page Title
Reference Number of Part Desired
Part Number
Part Description
Quantity of Part Desired
Providing this information will help ensure that the correct parts will be
delivered to you in an expedient manner without delay. Should additional
information be required for repair or replacement of certain components,
contact your Wrecker Manufacturer Authorized Representative.
The Manufacturer reserves the right, without notice or obligation, to improve
or modify their products, which may change the specifications, models and
feature availability.
VI-1
Section VI - PARTS (cont'd)
ALUMINUM BED ASSEMBLY
VI-2
Section VI - PARTS (cont'd)
ALUMINUM BED ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
8
14
1
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
1
2
2
2
2
2
4
15
8
6
4
2
3
10
4
2
4
1
1
1
1
1
25
26
1
1
27
1
28
2
0300132
0300134
0300250
0303273
0301669
0301740
0301741
0301742
0302180
0306009
0400044
0400077
0400088
0400177
0400181
0400213
0400392
0400408
0400492
0701172
0702517
0703203
0708913
0710822L
0710822R
0801482
0805215
0801547
0720283
0709850
0709851
0710777
0805175
0805176
0805177
0805178
0805179
0805180
0805181
0805182
LT0118
DESCRIPTION
WIRE TIE
HOSE CLAMP
4 TON WINCH ASSEMBLY (STD)
4 TON PLANETARY WINCH ASSEMBLY (OPT)
CABLE ASSEMBLY
GROMMET, MARKER LIGHT
SEALED LAMP (RED)
SEALED LAMP (AMBER)
BEARING PAD (SPECIFY BODY LENGTH)
BEARING PAD, 60"
DRIVE SCREW
SCREW, 1/4" X 1" SELF DRILLING
SCREW, 1/4"-20 X 5/8" STAINLESS
SCREW, 1/2"-13 X 1-1/4" HEX HD CAP
SCREW, 1/2"-13 X 1-1/2" HEX HD CAP
SCREW, 3/8"-16 X 1-1/2" HEX HD CAP
NUT. 3/8"-16 HEX NYLOK
NUT, 1/2"-13 HEX NYLOK
WASHER, 1/2" FLAT
SPACER, WINCH BRACKET
BEARING PAD STOP BAR
COVER PLATE
ANTI-TILT PLATE
MARKER LIGHT CASTING, LEFT
MARKER LIGHT CASTING, RIGHT
WINCH MOUNTING BRACKET (STD WINCH)
WINCH MOUNTING BRACKET (OPT WINCH)
CAR CARRIER BED (19' ALUMINUM)
HOSE TRAY (19' CARRIER)
HOSE TRAY (19' 6" CARRIER)
HOSE TRAY (20' CARRIER)
HOSE TRAY (21' CARRIER)
CAB PROTECTOR WELDMENT (32" HIGH)
CAB PROTECTOR WELDMENT (34" HIGH)
CAB PROTECTOR WELDMENT (36" HIGH)
CAB PROTECTOR WELDMENT (42" HIGH)
CAB PROTECTOR WELDMENT (45" HIGH)
CAB PROTECTOR WELDMENT (48" HIGH)
CAB PROTECTOR WELDMENT (52" HIGH)
CAB PROTECTOR WELDMENT (54" HIGH)
FRONT MARKER LIGHT (AMBER)
VI-3
Section VI - PARTS (cont'd)
STEEL BED ASSEMBLY
VI-4
Section VI - PARTS (cont'd)
STEEL BED ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
8
2
1
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
1
2
2
2
2
6
2
2
13
8
38
2
4
4
2
38
2
14
4
2
1
1
1
27
28
1
1
29
1
0300132
0300134
0300250
0303273
0301669
0301740
0301741
0301742
0301887
0306007
0306009
0306033
0400077
0400088
0400089
0400177
0400181
0400211
0400213
0400367
0400392
0400408
0400492
0701172
0705332
0708913
0801482
0805215
0801571
0720283
0709850
0709851
0710777
0805175
0805176
0805177
0805178
0805179
0805180
0805181
0805182
DESCRIPTION
WIRE TIE
HOSE CLAMP
4 TON WINCH ASSEMBLY (STD)
4 TON PLANETARY WINCH ASSEMBLY (OPT)
CABLE ASSEMBLY
GROMMET, MARKER LIGHT
SEALED LAMP (RED)
SEALED LAMP (AMBER)
LIGHT ASSEMBLY (RED)
BEARING PAD, 54"
BEARING PAD, 60"
BEARING PAD, 42"
SCREW, 1/4" X 1" SELF DRILLING
SCREW, 1/4"-20 X 5/8" STAINLESS
SCREW, 1/4"-20 X 1" STAINLESS
SCREW, 1/2"-13 X 1-1/4" HEX HD CAP
SCREW, 1/2"-13 X 1-1/2" HEX HD CAP
SCREW, 1/2"-13 X 1-3/4" HEX HD CAP
SCREW, 3/8"-16 X 1-1/2" HEX HD CAP
NUT. 1/4"-20 HEX NYLOK
NUT. 3/8"-16 HEX NYLOK
NUT, 1/2"-13 HEX NYLOK
WASHER, 1/2" FLAT
SPACER, WINCH BRACKET
COVER PLATE
ANTI-TILT PLATE
WINCH MOUNTING BRACKET (STD WINCH)
WINCH MOUNTING BRACKET (OPT WINCH)
CAR CARRIER BED (19' STEEL)
HOSE TRAY (19' CARRIER)
HOSE TRAY (19' 6" CARRIER)
HOSE TRAY (20' CARRIER)
HOSE TRAY (21' CARRIER)
CAB PROTECTOR WELDMENT (32" HIGH)
CAB PROTECTOR WELDMENT (34" HIGH)
CAB PROTECTOR WELDMENT (36" HIGH)
CAB PROTECTOR WELDMENT (42" HIGH)
CAB PROTECTOR WELDMENT (45" HIGH)
CAB PROTECTOR WELDMENT (48" HIGH)
CAB PROTECTOR WELDMENT (52" HIGH)
CAB PROTECTOR WELDMENT (54" HIGH)
VI-5
Section VI - PARTS (cont'd)
RIGHT APPROACH BED ASSEMBLY
VI-6
Section VI - PARTS (cont'd)
RIGHT APPROACH BED ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
27
21
1
2
2
2
4
2
8
2
2
2
11
10
40
4
6
40
10
2
1
5
1
22
1
0300250
0303273
0301669
0301740
0301741
0301742
0306007
0306009
0306051
0306054
0306094
0306108
0400077
0400088
0400089
0400181
0400211
0400367
0400408
0701172
0705332
0720023
0801482
0805215
0720283
0709850
0709851
0710777
4 TON WINCH ASSEMBLY (STD)
4 TON PLANETARY WINCH ASSEMBLY (OPT)
CABLE ASSEMBLY
GROMMET, MARKER LIGHT
SEALED LAMP (RED)
SEALED LAMP (AMBER)
BEARING PAD, 54"
BEARING PAD, 60"
TREE CLIPS
STORAGE TRAY MAT
BEARING PAD, 38-1/2"
BEARING PAD, 49-3/4"
SCREW, 1/4" X 1" SELF DRILLING
SCREW, 1/4"-20 X 5/8" STAINLESS
SCREW, 1/4"-20 X 1" STAINLESS
SCREW, 1/2"-13 X 1-1/2" HEX HD CAP
SCREW, 1/2"-13 X 1-3/4" HEX HD CAP
NUT. 1/4"-20 HEX NYLOK
NUT, 1/2"-13 HEX NYLOK
SPACER, WINCH BRACKET
COVER PLATE
HINGE PIN
WINCH MOUNTING BRACKET (STD WINCH)
WINCH MOUNTING BRACKET (OPT WINCH)
HOSE TRAY (19' CARRIER)
HOSE TRAY (19' 6" CARRIER)
HOSE TRAY (20' CARRIER)
HOSE TRAY (21' CARRIER)
23
1
0805175
0805176
0805177
0805178
0805179
0805180
0805181
0805182
CAB
CAB
CAB
CAB
CAB
CAB
CAB
CAB
24
25
26
1
1
2
0805198
0805324
GP132
CARRIER BED, RIGHT APPROACH (19' STEEL)
CABLE GUIDE ASSEMBLY
FRONT MARKER LIGHT (AMBER)
DESCRIPTION
PROTECTOR
PROTECTOR
PROTECTOR
PROTECTOR
PROTECTOR
PROTECTOR
PROTECTOR
PROTECTOR
VI-7
WELDMENT (32"
WELDMENT (34"
WELDMENT (36"
WELDMENT (42"
WELDMENT (45"
WELDMENT (48"
WELDMENT (52"
WELDMENT (54"
HIGH)
HIGH)
HIGH)
HIGH)
HIGH)
HIGH)
HIGH)
HIGH)
Section VI - PARTS (cont'd)
MOUNTING & TILT FRAME ASSEMBLY
(Continued on page VI-10)
VI-8
Section VI - PARTS (cont'd)
MOUNTING & TILT FRAME ASSEMBLY
(Continued on page VI-11)
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
1
3
18
4
2
1
2
2
2
3
8
10
1
4
4
1
2
2
1
1
1
1
1
12
8
2
2
1
12
9
1
28
20
14
20
0300032
0300113
0300132
0300134
0300188
0300273
0300867
0301223
0301390
0301397
0301601
0301642
0301671
0301740
0301741
0303385
0301932
0302201
0302474
0306041
0306385
0306386
0400021
0400045
0400060
0400061
0400066
0400070
0400121
0400122
0400150
0400181
0400211
0400367
0400392
DESCRIPTION
HOLE PLUG, 1"
GREASE FITTING
CABLE TIE
HOSE CLAMP, INSULATED
HOSE CLAMP, INSULATED
LICENCE PLATE ILLUMINATOR
CONTROL PANEL ILLUMINATOR
MUD FLAP
TAIL LIGHT ASSEMBLY (RED)
GREASE FITTING, 90°
CLAMP
SNAP RING, 1-1/4"
TOW LIGHT SOCKET
GROMMET MOUNTING KIT
SEALED LAMP (RED)
JUNCTION BOX
SAFETY CHAIN W/ HOOKS, 10' LONG
LIGHT, BACK UP (WHITE)
LYNCH PIN
TOOL BOX
BACK-UP ALARM (NOT SHOWN)
BACK-UP ALARM GROMMET (NOT SHOWN)
SCREW, #8-32 X 1/2" PAN HD
SCREW, #10-32 X 1/2" SELF TAPPING
SCREW, 1/4"-20 X 1/2" HEX HD CAP
SCREW, 1/4"-20 X 3/4" HEX HD CAP
SCREW, 1/4"-20 X 3/4" HEX HD CAP
SCREW, 1/4"-20 X 1" HEX HD CAP
SCREW, 3/8"-16 X 3/4" HEX HD CAP
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
SCREW, 3/8"-16 X 2-1/2" HEX HD CAP
SCREW, 1/2"-13 X 1-1/2" HEX HD CAP
SCREW, 1/2"-13 X 1-3/4" HEX HD CAP
NUT, 1/4"-20 HEX NYLOK
NUT, 3/8"-16 HEX NYLOK
VI-9
Section VI - PARTS (cont'd)
MOUNTING & TILT FRAME ASSEMBLY
(Continued from page VI-8)
VI-10
Section VI - PARTS (cont'd)
MOUNTING & TILT FRAME ASSEMBLY
(Continued from page VI-9)
REF.
NO.
NO.
REQ'D
PART
NUMBER
36
37
38
39
40
41
42
43
44
45
46
47
32
2
1
1
1
2
5
1
2
1
1
1
0400408
0400452
0400564
0500425
0500426
0700584
0702434
0704792
0705092
0709867
0705253
0705254
NUT, 1/2"-13 HEX NYLOK
LOCKWASHER, 1/4"
ROLL PIN
DECAL, CONTROL STATION (LEFT SIDE)
DECAL, CONTROL STATION (RIGHT SIDE)
CABLE
SHAFT, CYLINDER
PIVOT PIN
BAR, MUDFLAP
SAFETY PIN
PLATE, LIGHT MOUNTING (LEFT SIDE)
PLATE, LIGHT MOUNTING (RIGHT SIDE)
48
1
1
1
1
0720080
0720081
0720141
0720142
MUD FLAP MOUNTING BRACKET, LONG, RH
MUD FLAP MOUNTING BRACKET, LONG, LH
MUD FLAP MOUNTING BRACKET, SHORT, RH
MUD FLAP MOUNTING BRACKET, SHORT, LH
49
50
51
52
53
54
55
56
57
58
1
1
1
1
1
1
1
2
2
1
0801553
0801557
0801558
0801559
0801565
0801573
0801574
0802663
0802667
0805237
MOUNTING FRAME
CONTROL BOX HOOD, LEFT
CONTROL BOX HOOD, RIGHT
CENTER CONTROL HOUSING
TILT FRAME
TAIL LIGHT HOUSING (LEFT SIDE)
TAIL LIGHT HOUSING (RIGHT SIDE)
L-ARM STORAGE BRACKET
TOOL BOX/OIL TANK MOUNTING BRACKET
RESERVOIR ASSEMBLY
-59
60
61
62
63
-6
6
12
2
1
-0400211
0400408
0400492
0704784
0805054
BEDLOCK KIT
SCREW, 1/2"-13 X 1-3/4" HEX HD CAP
NUT, 1/2"-13 HEX NYLOK
WASHER, 1/2" FLAT
BEDLOCK PLATE
BEDLOCK ASSEMBLY
DESCRIPTION
VI-11
Section VI - PARTS (cont'd)
WHEEL LIFT & SLIDE-IN
TIRE RESTRAINT ASSEMBLY
VI-12
Section VI - PARTS (cont'd)
WHEEL LIFT & SLIDE-IN
TIRE RESTRAINT ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
5
2
1
2
1
1
1
1
2
2
1
2
2
2
3
2
2
2
3
1
2
1
1
1
1
1
1
2
2
1
1
2
1
1
1
1
1
0300113
0301398
0301850
0301956
0302183
0308129
0308130
0308131
0308132
0400148
0400150
0400161
0400221
0400367
0400392
0400393
0400398
0400451
0400480
0403004
0500241
0702131
0703277
0705524
0705238
0720460
0720463
0800583
0800590
0801009
0801012
0801332
0805149
0805245
0805434
0805470
0805471
DESCRIPTION
GREASE FITTING
RATCHET, TIE DOWN (INCL SCREW & NUT)
BEARING PAD
STRAP, RUBBER
BEARING PAD
DETENT BALL
PIPE PLUG
DETENT SPRING
"O" RING
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
SCREW, 3/8"-16 X 2-1/2" HEX HD CAP
BOLT, 3/8"-16 X 2-3/4" CARRIAGE
SCREW, 3/8"-16 X 1" CUP POINT ALLEN HD
NUT, 1/4"-20 HEX NYLOK
NUT, 3/8"-16 HEX NYLOK
NUT, 3/8"-16 HEX JAM
HALF NUT, 3/8"-16 HEX NYLOK
WASHER, 1/4" FLAT
WASHER, 3/8" FLAT
SCREW, 3/8"-16 X 3/4" BUTTON ALLEN HD
DECAL, SAFETY CHAIN WARNING
SHAFT, INNER TUBE CYLINDER
SLIDER, PAD
SHAFT, EXTEND CYLINDER
PIVOT PIN
PIN, CROSSBEAM PIVOT
WASHER, 1" O.D. X 3/8" I.D. FLAT
PIVOT, TIE DOWN
"T" HANDLE
SHAFT, PIN ASSEMBLY, UPPER BOOM
SHAFT, LIFT CYLINDER
TIRE RESTRAINT
OUTER BOOM
INNER BOOM
INNER CROSSTUBE WELDMENT
OUTER CROSSTUBE, RIGHT
OUTER CROSSTUBE, LEFT
VI-13
Section VI - PARTS (cont'd)
HYDRAULICS
(Continued on page VI-16)
VI-14
Section VI - PARTS (cont'd)
HYDRAULICS
(Continued on page VI-17)
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
10
3
1
1
1
6
1
1
1
6
1
2
1
1
1
1
1
1
2
5
1
2
1
2
2
1
2
1
2
0300044
0300055
0300056
0300058
0300065
0300071
0306157
0300133
0308151
0300142
0300165
0300208
0300209
0300288
0300347
0300692
0300789
0300865
0301403
0301424
0301473
0301478
0301484
0301522
0301524
0301640
0301658
0301659
0301660
DESCRIPTION
CONNECTOR 6MJ-8MB
HOSE BARB, 3/4" HOSE-12MP
HOSE BARB, 1" HOSE-16MP
HOSE, SUCTION 1"
SWIVEL, 12MB-12FPX
CLAMP, 1" HOSE
WINCH MOTOR
CLAMP, 3"-4" HOLDING VALVE RETAINER
OIL FILTER ASSEMBLY
ELBOW, 6MJ-4MP90
HOSE ASSEMBLY, 91"
TEE, 6MJ-6MJ-4MP
ELBOW, 6MJ-6MP90
STREET ELBOW, 3/4" 90°
PLUG, 1/2" SQ HD BLACK
STREET ELBOW, 1" 90°
CONNECTOR, 10MB-8MJ
CONNECTOR, 8MJ-8MB
HOSE ASSEMBLY, 80-1/2"
CONNECTOR, 6MJ-4MP
HOSE ASSEMBLY, 18"
HOSE ASSEMBLY, 54"
CYLINDER, WHEEL LIFT TILT
CONNECTOR, 6MJ-6MB
HOSE ASSEMBLY, 14"
VALVE, BED TILT CYLINDER LOCK
HOSE ASSEMBLY, 128"
HOSE ASSEMBLY, 150"
HOSE ASSEMBLY, 21"
VI-15
Section VI - PARTS (cont'd)
HYDRAULICS
(Continued from page VI-14)
VI-16
Section VI - PARTS (cont'd)
HYDRAULICS
(Continued from page VI-15)
REF.
NO.
NO.
REQ'D
PART
NUMBER
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
2
2
2
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
2
2
2
2
2
1
1
1
1
1
0301660
0301663
0301665
0301694
0301731
0301769
0301848
0301868
0301878
0301900
0301970
0302037
0300229
0302178
0302179
0302867
0306051
0306182
0400064
0400196
0400366
0400451
0400452
0703001
0704801
0704802
0801510
0805237
DESCRIPTION
HOSE ASSEMBLY, 21"
HOSE ASSEMBLY, 204"
ELBOW, 6MJ-8MP90
ORIFICE TEE
VALVE, TILT CYLINDER HOLDING
HOSE ASSEMBLY, 52"
ELBOW, 6MJ-6MP45
TEE, 4FP-4FP-4MP
HOSE ASSEMBLY, 137"
HOSE ASSEMBLY, 18"
CYLINDER, BED EXTEND
PTO
ELBOW, 8MJ-8MP90
CYLINDER, WHEEL LIFT EXTEND
CONTROL VALVE, 5 SPOOL
CYLINDER, BED LIFT
PUMP, HIGH PRESSURE HYDRAULIC
SKUFF JACKET
SCREW, 1/4"-20 X 2-1/4" RD HD SLOTTED
SCREW, 1/2"-13 X 1-1/4" SKT HD CAP
NUT, 1/4"-20 HEX
WASHER, 1/4" FLAT
LOCKWASHER, 1/4" HELICAL
BRACKET, W/L HOLDING VALVE MOUNTING
RETURN HOSE, 52"
RETURN HOSE, 192"
DIP STICK WELDMENT
RESERVOIR
VI-17
Section VI - PARTS (cont'd)
CONTROL & CROSSROD ASSEMBLY
VI-18
Section VI - PARTS (cont'd)
CONTROL & CROSSROD ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
6
2
10
2
1
10
4
12
3
4
10
10
15
5
15
10
2
1
2
2
2
2
4
5
1
2
0300341
0300834
0301638
0301720
0302179
0306006
0306122
0400121
0400140
0400243
0400392
0400393
0400465
0400482
0400532
0400543
0705242
0720456
0800795
0800796
0800797
0800798
0800799
0800800
0801274
0801566
DESCRIPTION
KNOB
KNOB, "IN/OUT" (RED, CABLE)
BRACKET, CONTROL HANDLE
KNOB, BALL
5-SPOOL CONTROL VALVE
SPRING, ANTI-RATTLE
END CAP, CONTROL HANDLE ROD
SCREW, 3/8"-16 X 3/4" HEX HD
SCREW, 3/8"-16 X 4" HEX HD
NUT, 3/8", "J" TINNERMAN
NUT, 3/8"-16 NYLOK
NUT, 3/8"-16 JAM
WASHER, 5/16" FLAT
LOCKWASHER, 3/8" HELICAL
CLEVIS PIN, 5/16" X 1"
COTTER PIN, 1/8" X 3/4"
CONTROL HANDLE PIVOT ROD
ANGLE, NO-SHAKE
FRONT INNER CONTROL HANDLE
FRONT OUTER CONTROL HANDLE
REAR INNER CONTROL HANDLE
REAR OUTER CONTROL HANDLE
VALVE SHIFTER
CONTROL ROD LINK
CONTROL ROD LINK, ANTI TILT
CONTROL HANDLE, CENTER
VI-19
Section VI - PARTS (cont'd)
RIGHT APPROACH LOCK MECHANISM
VI-20
Section VI - PARTS (cont'd)
RIGHT APPROACH LOCK MECHANISM
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12*
13*
14
15*
16*
17
18*
19*
20
21
22*
23*
24
25
26
6
1
4
4
4
2
5
4
6
6
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
2
0300113
0300845
0301670
0301586
0400410
0400430
0400492
0400510
0400537
0400549
0400560
0720083
0720084
0720120
0720121
0720122
0720132
0805213
0805214
0805247
0805248
0805249
0805250
0805251
0805252
0805253
DESCRIPTION
GREASE FITTING, 1/4"-28
COMPRESSION SPRING
BRONZE BUSHING
CLEVIS, 1/2"-13 THREADS
NUT, 1/2"-13 HEX JAM
NUT, 3/4"-10 HEX NYLOK
WASHER, 1/2" FLAT
WASHER, 3/4" FLAT
CLEVIS PIN, 1/2" X 1-1/2"
COTTER PIN, 1/8" X 1"
ROLL PIN, 5/32" X 1"
LOCK HOUSING BRACKET (DRIVER SIDE)
LOCK HOUSING BRACKET (PASSENGER SIDE)
LOCK PIN
LOCK PIN HOUSING
LOCK PIN HOUSING GUSSET
POSITION PIN, LOCK / UNLOCK
LOCK PLATE WELDMENT (DRIVER SIDE)
LOCK PLATE WELDMENT (PASSENGER SIDE)
LINKAGE CONTROL ARM (DRIVER SIDE)
LINKAGE CONTROL ARM (PASSENGER SIDE)
PIVOT PIN MOUNTING PLATE (DRIVER SIDE)
PIVOT PIN MOUNTING PLATE (PASS. SIDE)
LOCK PIN LINKAGE (DRIVER SIDE)
LOCK PIN LINKAGE (PASSENGER SIDE)
CENTER LINKAGE
*NOT SHOWN
VI-21
Section VI - PARTS (cont'd)
HYDRAULIC WINCH
VI-22
Section VI - PARTS (cont'd)
HYDRAULIC WINCH
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
1
1
1
1
1
2
1
1
1
1
1
5
1
1
1
1
2
1
1
1
1
1
16
1
2
1
1
1
1
6
6
1
1
4
1
1
2
1
2
1
0300261
0300290
0300381
0300398
0300399
0300447
0300448
0300449
0300450
0300451
0300452
0300453
0300454
0300455
0300456
0300458
0300459
0300460
0300461
0300462
0300463
0300464
0300465
0300466
0300467
0300468
0300471
0300472
0300473
0300474
0300475
0300476
0600477
0300569
0300694
0300695
-----
DESCRIPTION
LEVER
COUPLING
DRUM
YOKE
SCREW
GASKET
KEY
SCREW
KEY
SHAFT
CLUTCH HOUSING
BUSHING
SCREW
SPRING
BALL
SPACER
PLUG
HOUSING
PLUG
REDUCER
DRAG BRAKE
SPRING
SCREW
CAP
BEARING
WORM
SEAL
HUB
GEAR
WASHER
SCREW
GASKET
COVER
SCREW
CAP ADAPTER
SCREW
KEY
SHAFT
KEY
CLUTCH
* When ordering specify which serial number.
VI-23
Section VI - PARTS (cont'd)
WINCH CLUTCH CONTROL
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
1
1
1
1
2
2
1
4
1
1
2
1
1
1
1
0301397
0301532
0301588
0306015
0400116
0400126
0400392
0400410
0400492
0400537
0400546
0400560
0710918
0710919
0805170
0805151
DESCRIPTION
GREASE FITTING, 90°
"T" HANDLE
ADJUSTING YOKE
SPRING COMPRESSION
SCREW, 5/16"-18 X 1/2" SQ HD SET
SCREW, 3/8"-16 X 1" HEX HD CAP
NUT, 3/8"-16 NYLOK
NUT, 1/2"-13 JAM
WASHER, 1/2" FLAT
PIN, 1/2" X 1-1/2" CLEVIS
PIN, 1/8" X 1-1/4" COTTER
PIN, 5/32" X 1" ROLL
MOUNTING ANGLE
SPRING HOLDER
CONTROL ROD
BELL CRANK
VI-24
Section VI - PARTS (cont'd)
CABLE TENSIONER ASSEMBLY
(STANDARD 4-TON WINCH)
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
2
2
2
2
4
2
1
1
0301729
0400126
0400130
0400480
0400392
0400554
0800908
0800909
DESCRIPTION
TENSIONING SPRING
SCREW, 3/8"-16 X 1" HEX HD CAP
SCREW, 3/8"-16 X 3-1/2" HEX HD CAP
WASHER, 3/8" FLAT
NUT, 3/8"-16 HEX NYLOK
ROLL PIN, 3/8" X 1"
TENSIONING PLATE
CABLE TENSIONER BRACKET
VI-25
Section VI - PARTS (cont'd)
CABLE ROLLER ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
-2
2
1
0900892
0400177
0400408
0805037
DESCRIPTION
CABLE ROLLER ASSEMBLY
SCREW, 1/2"-13 X 1-1/4" HEX HD
NUT, 1/2"-13 NYLOK
CABLE ROLLER GUIDE WELDMENT
VI-26
Section VI - PARTS (cont'd)
STANDARD PTO PANEL
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
1
2
2
2
0301675
0400061
0400366
0400452
DESCRIPTION
PANEL (COMPLETE)
SCREW, 1/4"-20 X 3/4"
NUT, 1/4"-20 HEX
LOCKWASHER, 1/4"
VI-27
Section VI - PARTS (cont'd)
HYDRAULIC CYLINDERS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
1
--
0301970
0306388
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
2
--
0302867
0306133
DESCRIPTION
CYLINDER, BED EXTEND (COMPLETE)
SEAL KIT, BED EXTEND CYLINDER
DESCRIPTION
CYLINDER, BED TILT (COMPLETE)
SEAL KIT, BED TILT CYLINDER
VI-28
Section VI - PARTS (cont'd)
HYDRAULIC CYLINDERS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
1
--
0302178
0306134
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
1
--
DESCRIPTION
CYLINDER, WHEEL LIFT EXTEND (COMPLETE)
SEAL KIT, WHEEL LIFT EXTEND CYLINDER
DESCRIPTION
0301484 CYLINDER, WHEEL LIFT LIFT (COMPLETE)
0306135 SEAL KIT, WHEEL LIFT LIFT CYLINDER
VI-29
Section VI - PARTS (cont'd)
LIGHT KIT
REF.
NO.
PART
NUMBER
1
2
3
0301390
0302201
0304127
REF.
NO.
PART
NUMBER
DESCRIPTION
1
2
3
0301740
0301741
0301742
TAIL LIGHT GROMMET
LIGHT, SEALED RED (MARKER)
LIGHT, SEALED AMBER (MARKER)
DESCRIPTION
LIGHT, SEALED RED (STOP & TURN)
LIGHT, SEALED WHITE (BACK-UP)
TAIL LIGHT GROMMET
VI-30
Section VI - PARTS (cont'd)
LIGHT KIT
REF.
NO.
PART
NUMBER
DESCRIPTION
1
GP132
LIGHT, AMBER MARKER, RECTANGULAR (COMPLETE)
REF.
NO.
PART
NUMBER
DESCRIPTION
1
0306126
LIGHT ASSEMBLY (COMPLETE)
VI-31
Section VI - PARTS (cont'd)
LIGHT KIT
REF.
NO.
PART
NUMBER
DESCRIPTION
1
LT0118
LIGHT, AMBER MARKER, RECTANGULAR (COMPLETE)
REF.
NO.
PART
NUMBER
DESCRIPTION
1
2
3
4
5
6
7
8
0301505
0304146
0304148
0304149
0304150
0304151
0304152
0304153
WORK LIGHT (COMPLETE)
HOUSING, WORK LIGHT
MOUNTING BRACKET
MOUNTING SCREW
LOCKWASHER
PIVOT SCREW
BULB, WORK LIGHT
NUT
VI-32
Section VI - PARTS (cont'd)
LIGHT KIT
REF.
NO.
PART
NUMBER
1
2
3
4
5
6
7
8
174008003
0304146
0304148
0304149
0304150
0304151
0304152
0304153
DESCRIPTION
RECTANGULAR WORK LIGHT (COMPLETE)
HOUSING, WORK LIGHT
MOUNTING BRACKET
MOUNTING SCREW
LOCKWASHER
PIVOT SCREW
BULB, WORK LIGHT
NUT
VI-33
Section VI - PARTS (cont'd)
OPTIONAL OUTER CROSSTUBE &
3-WAY PIVOT TIRE RESTRAINT ASSEMBLY
VI-34
Section VI - PARTS (cont'd)
OPTIONAL OUTER CROSSTUBE &
3-WAY PIVOT TIRE RESTRAINT ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
--
1
0904152
--
1
0904153
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
4
2
2
2
2
2
1
1
2
2
2
2
2
2
2
2
2
2
2
1
1
2
2
2
2
1
1
1
1
2
2
0300113
0301399
0301956
0302640
0302641
0302648
0303918
0400044
0400161
0400349
0400367
0400398
0400451
0400480
0400483
0400560
0707505
0712933
0712934
0712928
0712929
0714415
0800583
0306564
0802187
0802675
0802676
0803648
0803649
0902382
HD0107
DESCRIPTION
OUTER CROSSTUBE & PIVOT, LEFT
(COMPLETE)
OUTER CROSSTUBE & PIVOT, RIGHT
(COMPLETE)
GREASE FITTING
STRAP, TIE DOWN W/ RATCHET (OPT.)
STRAP, 9" RUBBER
PLUG, DRY-OUT HOLE
SPRING, PLUNGER PIN
"T" HANDLE
CABLE ASSEMBLY
DRIVE SCREW, #10 X 1/2"
BOLT, 3/8"-16 X 2-3/4" CARRIAGE (OPT.)
SCREW, 3/8"-16 X 3/4" FL HD SKT
NUT, 1/4"-20 HEX NYLOK
NUT, 3/8"-16 NYLOK HALF (OPT.)
WASHER, 1/4" FLAT
WASHER, 3/8" FLAT (OPT.)
LOCKWASHER, 3/8" COUNTERSUNK
PIN, ROLL 5/32" X 1"
PIN, PLUNGER
PIN ALIGNMENT
CABLE PROTECTOR
END PLATE WELDMENT, L.H.
END PLATE WELDMENT, R.H.
PIN
PIVOT TIE DOWN (OPT.)
TEE HANDLE
SHAFT, PIVOT
OUTER CROSSTUBE, L.H.
OUTER CROSSTUBE, R.H.
TIRE RESTRAINT, SCOOP, LEFT
TIRE RESTRAINT, SCOOP, RIGHT
1" NYLON POLY-COAT STRAP (OPT.)
SPRING PIN, 3/16" X 2"
VI-35
Section VI - PARTS (cont'd)
OPTIONAL LIGHTING ACCESSORIES
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
2
2
1
1
8
1
8
1
2
8
2
2
0300095
0300897
0301359
0301601
0400043
0400061
0400356
0400367
0400392
0400520
0709872
0801777
DESCRIPTION
SPOT LIGHT W/GASKET
GROMMET, RUBBER
WRECKER SPECIAL LIGHT
WIRE CLIP
SCREW, #10-24 X 1" MACHINE
SCREW, 1/4"-20 X 3/4" HEX HD CAP
NUT, #10-24 HEX NYLOK
NUT, 1/4"-20 HEX NYLOK
NUT, 3/8"-16 HEX NYLOK
LOCK WASHER, #10
RUBBER CUSHION
"T" BOLT ADAPTER
VI-36
Section VI - PARTS (cont'd)
OPTIONAL EQUIPMENT
INDEPENDENT TOWBAR ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
-1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
-3
2
5
2
1
2
1
1
1
2
1
1
1
1
1
-0300113
0301381
0301642
0301723
0301798
0302368
0400436
0500241
0702418
0702434
0800777
0800784
0800898
0805030
0805150
DESCRIPTION
INDEPENDENT TOW BAR ASSEMBLY (COMP.)
GREASE FITTING
SNAP RING, 3/4"
SNAP RING, 1-1/4"
GUARD, TOW BAR BUMPER
CYLINDER, TOW BAR EXTEND
CYLINDER, TOW BAR
NUT
DECAL, SAFETY CHAIN WARNING
SHAFT, EXTEND CYLINDER
PIN, CYLINDER
TUBE, TOW BAR INNER
PIN, TOW BAR PIVOT
CROSSTUBE, TOW BAR
SHAFT, TOW BAR PIVOT, PIN WITH KEEPER
TUBE, TOW BAR OUTER
VI-37
Section VI - PARTS (cont'd)
OPTIONAL EQUIPMENT
FIXED TOWBAR ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
-1
2
3
4
5
6
7
8
9
10
11
12
13
14
-2
1
2
1
2
1
1
1
1
1
1
1
1
1
-0300110
0300113
0301381
0301642
0301723
0301798
0400436
0500241
0700058
0702418
0800777
0800784
0800924
0801403
DESCRIPTION
FIXED TOW BAR ASSEMBLY (COMPLETE)
SNAP RING, 1"
GREASE FITTING
SNAP RING, 3/4"
SNAP RING, 1-1/4"
GUARD, TOW BAR BUMPER
CYLINDER, TOW BAR EXTEND
NUT
DECAL, SAFETY CHAIN WARNING
SHAFT, TOW BAR PIVOT
SHAFT, EXTEND CYLINDER
TUBE, TOW BAR INNER
PIN, TOW BAR PIVOT
CROSSTUBE, TOW BAR
TUBE, TOW BAR OUTER
VI-38
Section VI - PARTS (cont'd)
OPTIONAL EQUIPMENT
TOWBAR CYLINDER
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
1
--
0301798
0306136
DESCRIPTION
CYLINDER, TOWBAR (COMPLETE)
SEAL KIT, TOWBAR CYLINDER
VI-39
Section VI - PARTS (cont'd)
OPTIONAL EQUIPMENT
TOWING SLING
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
2
8
8
8
2
2
1
1
2
0300176
0400105
0400156
0400392
0701919
0701920
0800608
0800609
0800873
DESCRIPTION
"J" HOOK ASSEMBLY
SCREW, 5/16"-18 X 1-1/4" SELF-TAPPING
CARRIAGE BOLT, 3/8"-16 X 1-1/4"
NUT, 3/8"-16 HEX NYLOK
TOW SLING BELT
GRIP PLATE
CHAIN KEEPER, LEFT
CHAIN KEEPER, RIGHT
BELT RETAINER
VI-40
Section VI - PARTS (cont'd)
OPTIONAL DASHBOARD PANEL
VI-41
NOTES
NOTES
CENTURY®
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive • Ooltewah, Tennessee 37363 • (423) 238-4171
www.millerind.com