sec 19 spreaders - Maritime Farm Supply ltd.

Transcription

MARITIME FARM SUPPLY LTD.
“Your Connection to All Your Equipment Needs”
“All Applicable Taxes Extra:
www.maritimefarmsupply.com
Poly-Stainless MP+3 Multi-Purpose
Applicator
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
Fertilize, seed or apply granular chemicals with just one applicator. Comes with three sets of Full-Rate metering wheels.
Standard Equipment:
•
•
•
•
•
•
•
•
2.3 cu.ft (140 lb capacity for fertilizer at 60 lb per cu ft density /100 lbs capacity for seed and chemical) polyethylene hopper with stainless steel housing to resist corrosion. Includes u-frame mount with 1/2” pre-drilled
holes and slots for mounting.
Includes four full-rate black metering wheels for small seeds like alfalfa, canola and granular chemicals: four
re metering wheels for small grains such as oats, wheat, rice, barley and fertilizer; four yellow hi-output fertilizer metering wheels. Operator can install from one to four outlets on a single applicator depending upon
field requirements. Note: for chemical and fertilizer applications requiring less that 4 lb./acre, customer will
need to order half-rate metering wheels.
Product is fed under the metering wheel to dispense particles down the tube. Positive shutoff when metering
stops.
Speed compensated rate if ground driven
Non-speed compensated electric drive available
Factory rate charts are based on a drive input to the hopper shaft of 2 or 4 revolutions in 88 feet provided by
Gandy ground drive or a user-made sprocket and chain drive from a parent implement shaft.
Sprocket cluster package, ordered separately, sets the rates and can control several hoppers set up in line
through the use of connector tubes
Requires 1.5” ID tubing with hose clamps to secure tubing to outlet. 7/8” tubing with hose clamps are required when spout adapters are used. Order separately as needed.
Some assembly required.
SPECIFICATIONS: Neutral polyethylene hopper, heat reflective silver lid with strap latches, positive displacement applicator assembly. Includes red
(F) fertilizer, black (C) chemical and yellow (V) hi-output fertilizer metering wheels with open stainless steel housing and see-through weather-guard
shield. U-frame mounting bracket with 1/2” holes and slots included. Internal agitator standard.
EXTRA EQUIPMENT: Rate control sprocket package, drop tubing, hose clamps ordered separately. Purchaser will have to provide chain and drive
sprocket to hopper input shaft from the parent implement’s live shaft to provide 2 or 4 rpm in 88ft ground travel to the Gandy input shaft depending on
chemical rate, or purchase the Gandy ground drive package
OPTIONS: Agitator that secures to internal drive shaft is standard equipment; however, if multiple hoppers are mounted in line, connector tubes will be
needed to connect each hopper’s drive and agitator shafts. Number of in-line hoppers possible will depend on torque created by product being applied.
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
1. CHOOSE AN APPLICATOR PACKAGE
09PDMS
Multi-Purpose polY stainless applicator with four black metering wheels for small seeds & granular
chemicals; four red metering wheels for small grains and fertilizer, four yellow hi-output fertilizer
metering wheels. Includes four spout adapters for use with granular chemical U-frame mounted
bracket with 1/2” pre-drilled holes and slots for mounting and internal agitators. Operators can
configure applicator from one to four outlets. Blank plates included to block off unused outlets.
39 lbs
$886.00
85 lbs
880.00
2. CHOOSE A GROUND OR ELECTRIC DRIVE PACKAGE BELOW
09094903
Speed-compensated ground drive package with 480/400x8, 4-ply tire. Attaches to diamond or flat
tool bar, includes drive sprockets and chain.
09099934
12-volt, 4 amp, 1/64 hp electric motor with on/off switch, drive sprockets, chain and guard. Drives
09004956
12-volt, 25 amp, 1/4 hp heavy-duty electric motor complete with on/off switch, drive sprockets,
chain and guard. Drives up to eight hoppers.
NOVEMBER 2014
PRICES ON U.S. MANUFACTURED GOODS SUBJECT TO CHANGE
WITHOUT NOTICE DUE TO CURRENCY FLUCTUATIONS
342.00
1,250.00
GST # R101743045
Sheet 203
NOTE: PRODUCT NOT IN STOCK IS SUBJECT TO FREIGHT CHARGES
•
Poly-Stainless MP+3 Multi-Purpose
Applicator
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
09099930
Set of 12 sprockets to regulate application rates when electric or ground drive is chosen. Includes
sprockets, stub connector, chain and guard.
6 lbs
210.00
4. SELECT TUBING
M06-1500-010
1-1/2” I.D clear flexible tubing. Order in foot lengths.
M11-0024-000
Hose Clamp, 1” - 2”
M06-0875-000
7/8” I.D. clear flexible tubing. Order in foot lengths. For use with hopper when seeding or applying low
rates of granular chemicals and requires smaller tube for opener placement. Note: this tubing is used
with spout adapter, no. 09094899-9 for granular chemical applications.
M11-0012-010
Hose Clamp, 5/8” - 1 1/4”. For use with 7/8” ID tubing
4.00/ft
2.00
4.00/ft
2.00
5. OPTIONAL CONNECTOR PKG’s WHEN MOUNTING MULTIPLE HOPPERS IN-LINE
09074321
Connector drive tube used to connect metering shaft or drive shaft in line, up to 42” spacing. Note: If
agitators used, separate connector drive tubes will be needed to connect the drive shafts and agitator
shafts.
3 lbs
76.00
09074323
Connector drive tube, used to connect metering shaft or drive shat in line, up to 80” spacing. Note: If
agitators used, separate connector drive tubes will be needed to connect the drive shafts and agitator
shafts.
4 lbs
88.00
7. FIELD INSTALLED OPTIONS AND WEAR PARTS
09099931
Agitator package, 2 piece, option for all 2.3 cubic foot top feed PDA hoppers.
62851-75
Black C full0rate wheel with cavity inserts to be used for granular chemicals and small seed. Order
number required
M10-0001-020
Replacement full-rate black C wheel - does not included cavity inserts. Order number required.
09096918
Electric clutch package to provide shutoff on existing installations.
09099946
Latch package for poly hopper lid (replacement)
42.00
M05-0000-008
Rubber replacement latch only, 4”
20.00
09094899-9
Adapter to insert into metering cup to accept .875” tubing
6.00
C08-0138-030
#6-32 sheet metal screw
1.00
NOVEMBER 2014
32.00
6 oz
18.00
9.00
438.00
GST # R101743045
Sheet 203
3. RATE CONTROL SPROCKET PACKAGE
POLY HOPPER WITH CAM GAUGE
FOR INSECTICIDES & HERBICIDES
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
2.3 cu ft capacity poly hoppers
OPTIONAL Lock’n Load lid available
U-frame bracket included with holes and slots for mounting
2, 3 or 4 openings per hopper
SPECIFICATIONS: 100 lb (46 kg) capacity low density polyethylene hopper (approximate, with clay ag chemical granules at 45 lb
per cu ft), with bolt-on stainless steel hopper bottom and slide; bolt-n mounting for easy removal; precision cam-type rate gauge; fivebladed Flo-Control rotor; sealed bearings. Color, natural, with silver lid and latch straps. Note: this bottom & slide is not interchangeable with the snap-on bottom & slide used with steel hoppers. U-frame mounting bracket with 1/2” holes and slots included.
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
1. SELECT A 100 LB CAP. POLY CAM-GAUGE APPLICATOR PKG WITH RUBBER ROTOR
BAR, HOSES, HOSE CLAMPS, STABILIZERS AND CLAMP STRAPS
09PC02EM-R
100 lb row crop applicator pkg consisting of hopper with two outlets, twin rubber rotor bar, “U”
frame mounting brackets, two 42” flexible tubes, hose clamps, stabilizers and clamp straps.
29 lbs
$741.00
09PC03EM-R
100 lb row crop applicator pkg consisting of hopper with three outlets, twin rubber rotor bar, “U”
31 lbs
767.00
09PC04EM-R
100 lb row crop applicator pkg consisting of hopper with four outlets, twin rubber rotor bar, “U”
33 lbs
796.00
888.00
2. OPTIONAL GROUND OR ELECTRIC DRIVE PACKAGES
09069286-C1
Ground-drive, non-speed compensating with steel wheel. Attaches to diamond or flat tool bar.
Comes with driven sprocket and chan.
69 lbs
09069286R-C1
Ground-drive, non-speed compensating with rubber wheel. Attaches to diamond or flat tool bar.
Comes with driven sprocket and chan.
53 lbs
09099928
12-volt, 1/64 hp motor with mounting, motor, chain, guard. May drive up to 2 hoppers
354.00
09099929
12-volt, 1/32 hp motor with mounting, motor, chain, guard. May drive up to 3 hoppers
507.00
3. OPTIONAL LOCK N’ LOAD COVER
M10-0002-116
Lock N” Load lid in lieu of standard lid. Deduct M10-0001-115 from above package, and add
price to whole goods price.
09LLV
Lock N” Load valve for attachments to Lock N’ Load Lid.
26.00
101.00
4. OPTIONAL CONNECTOR PACKAGES WHEN MOUNTING MULTIPLE HOPPERS IN-LINE
09074321
Connector drive tube for hoppers spaced up to 42” apart
3 lbs
76.00
09074323
3 lbs
88.00
NOVEMBER 2014
GST # R101743045
Sheet 203
•
•
•
•
POLY HOPPER WITH CAM GAUGE
TAB# 19 SPREADERS
US PRODUCT
FOR INSECTICIDES & HERBICIDES
www.gandy.net
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
5. OPTIONAL TUBING AND RO-BANDERS
M06-0875-000
.875 inch ID clear flexible tubing. Order by the foot.
Per Foot
$4.00
2406224-36
.810 inch ID clear tubing - 36” length (available in lengths up to 108”)
M11-0012-010
Mini-hose clamp, 5/8” x 1 1/4” (secures tube to spout)
09105D
5” ro-bander
2 lbs
34.00
09107D
7” ro-bander
2 lbs
32.00
09110D
10” ro-bander
2 lbs
39.00
09114
14” ro-bander (comes with mounting brackets)
2 lbs
73.00
09073673
Attaching bracket for single ro-bander to tool bar
2 lbs
64.00
09073649EMS
Adjustable tol bar mount (12-24”) fits up to a 5” diamond or 7” square tool bar
14 lbs
150.00
12.00
2.00
6. FIELD INSTALLED MOUNTING OPTIONS
NOVEMBER 2014
GST # R101743045
Sheet 203
PART NUMBER
JUMBO PDM ROW APPLICATOR PKG
WITH FULL-RATE CHEMICAL WHEEL
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
Positive Displacement Packages for Pesticides
•
•
•
•
•
•
•
SPECIFICATIONS: Steel hopper, PDM metering bottom, full-rate black ( C) chemical metering wheels, metering cups, full length and half
slide closures. U-frame bracket with 1/2” holes and slots for mounting. Order separately: Rate control sprocket package, drop tubing, hose
clamps.
USER FABRICATED GROUND-DRIVE: Will have to provide chain and drive sprocket to hopper input shaft from the parent implement’s live
shaft to provide 2 or 4 rpm to the Gandy input shaft depending on chemical rate, or purchase the Gandy ground drive package.
OPTIONS: Lock’n Load lid and valves. Agitators that pin to internal drive shafts are available for materials which do not flow well. Order
according to number of outlets. If multiple hoppers are mounted in line, connector tubes will be needed to connect each hopper’s drive.
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
1. SELECT A FULL-RATE JUMBO PDM APPLICATOR (approximately 45 lb capacity)
09M4PDM
Jumbo hopper, 4-outlet PDM bottom, full-rate black ( C) chemical metering wheel in place. Includes slide closures to block off unused outlets
36 lbs
$536.00
2. SELECT A RATE CONTROL SPROCKET
09095917
Set of 12 sprockets to regulate application rates on Gandy PDM systems for ground drive, electric
motor drive or hydraulic motor drive. Includes stub connector, chain and guard.
210.00
You must have a rate control sprocket set in order to adjust application rates for your individual
applicator. If you are mounting multiple hoppers in-line, you only need one (!) rate control sprocket
set. If you are ordering multiple hoppers and they cannot be placed in-line, you will need to order
a rate control sprocket set for each individual applicator.
3. OPTIONAL ELECTRIC OR GROUND DRIVE PACKAGES
09094907
12-volt electric motor drive, complete with switch, drive sprocket, chain and guard. 4 amp 1/64 hp
to drive up to tow hoppers. Other motors will deliver different rpm’s and not follow calibration rate
guides ( Non-speed compensated electric motor drive pkg)
09094903
Ground drive with 480-8 tire. Attaches to diamond or flat tool bar, includes drive sprockets and
chain. (speed-compensated ground drive pkg)
309.00
85 lbs
880.00
11 lbs
169.00
4. OPTIONAL HOPPER EXTENSION
09176744
Hopper extension for Jumbo applicator to add 45 lbs additional capacity
If ordered as original equipment, deduct price of 09173668/40 lid from hopper pkg.
NOVEMBER 2014
-8.00
GST # R101743045
Sheet 203
•
Steel PDM hoppers provide positive displacement metering and rate control by sprocket
cluster
Absolute shutoff when metering stops and, if ground driven, compensates for changes
in field speeds
Feeds material under the metering wheel, down delivery tube
Includes slide closures to block off unused outlets
Factory rate charts based on input to the hopper shaft of 2 or 4 revolutions in 88 feet
either from a Gandy ground drive or a sprocket and chain drive from the parent implement’s live shaft
Electric, not speed compensating and speed-compensated ground drive available
Sprocket cluster package, ordered separately, used to set the rates, can control several
hoppers connected in line
PDM metering available as attachments to convert Gandy hoppers with cam gauge
metering
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
PART NUMBER
DESCRIPTION
LIST PRICE
FRT EXTRA
WGT
By adding the letters LL to the end of the any model row hopper, the hopper will have the lid die
cut to accept a Lock ‘N Load valve. Add amount to the price in price list.
09LLV
Lock ‘ N Load valve for attachment to row applicator
$23.0
101.00
09074321
3 lbs
76.00
09074323
3 lbs
88.00
M06-0875-000
2406224-36
.810 inch ID clear tubing—36” length (available in lengths up to 108 inches)
M11-0012-010
Mini-hose clamp, 5/8” x 1 1/4” (secures tube to spout)
4.00
12.00
2.00
09105D
5” ro-bander
2 lbs
34.00
09107D
7” ro-bander
2 lbs
32.00
09110D
10” ro-bander
2 lbs
39.00
09114
2 lbs
73.00
09073673
2 lbs
64.00
14 lbs
150.00
09073649EMS
Adjustable tool bar mount (14” to 24” fiits up to 5” diamond or 7” square tool bar
9. FIELD INSTALLED OPTIONS
09094901-1
Agitator for 1-outlet PDM applicator
51.00
09094901-2
58.00
09094901-3
57.00
09094901-4
64.00
09MPDM-1
1-outlet PDM replacement bottom, Jumbo, full-rate chemical wheel in place
271.00
09MPDM-2
305.00
09MPDM-3
338.00
09MPDM-4
379.00
09096918
Electric clutch package to provide shutoff on existing PDM installations
438.00
09094906
Conversion pkg to mount existing 1/64 hp 12-volt electric motor to right side of hopper so PDM
metering wheels rotate in underfed direction. Electric motor drive is not speed-compensated.
Package includes chain guard, 36—T sprocket and 48-link #41 chain. Note: if high rates of
certain chemicals are required, you may need to substitute the 32T sprocket in existing 1/64 hp
12V motor pkg #09075589, or order 32T sprocket #09071589-16 separately. Check rate chart
for sprocket used.
NOVEMBER 2014
72.00
GST # R101743045
Sheet 203
LL
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
DESCRIPTION
LIST PRICE
FRT EXTRA
WGT
09096921R
Half-rate red (F) wheel with two spacers for seeds at high rates. Order number required
4 oz
$55.00
M10-0001-022
.230 black metering wheel used for low alfalfa rates. Order two .50” spacers per wheel
3 oz
16.00
62851-40
.50” spacer. Order two spacers per outlet using .230” seed wheel (alfalfa)
6 oz
32.00
09096921
Package of half-rate chemical ( C) metering wheel and two spacers for 1 1/4” outlet
4 lbs
40.00
09072654-3
U-frame lid lock package for attachment to existing Super of Jumbo applicator
4 lbs
47.00
09078765
Hopper lid lock package for attachment to existing Super or Jumbo applicator
8 oz
33.00
09MLL
Jumbo hopper lid and hinge only, opening for one Lock ‘N Load valve
4 lbs
60.00
09178768
Suspender for placement inside hopper to keep granules suspended and create even flow of
materials around rotor bar
2 lbs
29.00
NOVEMBER 2014
GST # R101743045
Sheet 203
PART NUMBER
WITH HALF-RATE CHEMICAL WHEEL
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
Positive Displacement Packages for Pesticides
• Half-rate ( C) chemical wheel installed for low application
rates for pesticides
• Available with up to four outlets
Includes shutoff slides to individually close unused outlets
U-frame mounting bracket included
Jumbo applicator with approximately 45 lbs capacity
SPECIFICATIONS: Steel hopper, PDM metering bottom; package suffix of “T” indicates half rate black ( C) chemical metering wheels and spacers in
place, metering cups, full length and half slide closures. Rate chart included.
EXTRA EQUIPMENT: Purchaser will have to provide chain and drive sprocket to hopper input shaft from the parent implement’s live shaft to provide 2
or 4 rpm to the Gandy input shaft , or purchase the Gandy ground drive package. U-frame is included in Jumbo packages. If existing hopper is
equipped with standard 1 1/4” black ( C) chemical wheels, half rate chemical wheels and spacers can be ordered per outlet as package 09096921.
OPTIONS: Agitators that pin to internal drive shafts are available for materials that do not flow well. Order according to number of outlets. If multiple
hoppers are mounted in line, connector tubes will be needed to connect each hopper’s drive. A stub shaft connector will be needed for connection to
the parent hopper.
PART NUMBER
DESCRIPTION
LIST PRICE
FRT EXTRA
WGT
1. SELECT A HALF-RATE JUMBO PDM INDIVIDUAL APPLICATOR OR PACKAGE
09M4PDM-T
Jumbo hopper, 4-outlet PDM bottom, half-rate black ( C) chemical wheel in place. Includes
slide closures to block off unused outlets.
$668.00
2. SELECT A RATE CONTROL SPROCKET
09095917
Set of 12 sprockets to regulate application rates on Gandy PDM systems for ground drive,
electric motor drive, or hydraulic motor drive; stub connector, chain and guard included.
210.00
You must have a rate control sprocket set in order to adjust application rates for your individual
applicator. If you are mounting multiple hoppers in-line, you only need one (!) rate control
sprocket set. If you are ordering multiple hoppers and they cannot be placed in-line, you will
need to order a rate control sprocket set for each individual applicator.
3. CHOOSE A DRIVE PACKAGE
09094907
12-volt electric motor drive, complete with switch, drive sprockets, chain and guard. 4 amp
1/64 hp to drive up to two hoppers. Other motors will deliver different rpm’s and not follow
calibration rate guides.
09094903
Ground drive package with 480-8 tire. Attaches to diamond or flat tool bar, includes drive
sprockets and chain.
309.00
85 lbs
880.00
13 lbs
169.00
09176744
Hopper extension for Jumbo applicator to add 45 lbs of additional capacity
If ordered as original equipment, deduct price of 09173668/40 lid from hopper package
-8.00
LL
By adding the letters LL to the end of any model row hopper, the hopper will have the lid die
cut to accept a Lock N’ Load valve. Add amount to price in the price list
09LLV
Lock N’ Load valve for attachment to row applicator
NOVEMBER 2014
23.00
101.00
GST # R101743045
Sheet 203
•
•
•
WITH HALF-RATE CHEMICAL WHEEL
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
PART NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
Connector drive tube for hoppers spaced up to 42” apart.
3 lbs
$76.00
09074323
3 lbs
88.00
M06-0875-000
4.00
2406224-36
.810 inch ID clear tubing—36” length (available up to 108”)
M11-0012-010
Mini-hose clamp, 5/8” x 1 1/4”. (secures tube to spout)
09105D
5” ro-bander
2 lbs
34.00
09107D
7” ro-bander
2 lbs
32.00
09110D
10” ro-bander
2 lbs
39.00
09114
14” ro-bander
2 lbs
73.00
09073673
2 lbs
64.00
14 lbs
150.00
12.00
2.00
09073649EMS
Adjustable tool bar mount (14” to 24”) fits up to 5” diamond or 7” square tool bar
09094901-1
Agitator for 1-outlet Jumbo, Super or Junior PDM applicator
51.00
09094901-2
58.00
09094901-3
57.00
09094901-4
64.00
09MPDM-1T
1-outlet PDM replacement bottom, Jumbo hopper, half-rate chemical wheel in place
324.00
09MPDM-2T
379.00
09MPDM-3T
499.00
09MPDM-4T
519.00
09096918
Electric clutch package to provide shutoff on existing PDM installations
438.00
09094906
Conversion package to mount existing 1/64 hp 12-volt electric motor to right side of hopper so
PDM metering wheels rotate in underfed direction. Electric motor drive is not speedcompensating. Package includes chain guard, 36-T sprocket and 49-link, #41 chain. Note: if
high rates of certain chemicals are required, you may need to substitute the 32T sprocket in
existing 1/64 hp 12V motor package #09075589, or order 32T sprocket #09071589-16 separately. Check rate chart for sprocket used.
09096921R
Half-rate red (F) wheel with two spacers for seeds at high rates. Order number required
4 oz
55.00
M10-00001-022
.230 black metering wheel used for low alfalfa rates. Order two .50” spacers per wheel
3 oz
16.00
62851-40
.50” spacers. Order tow spacers per outlet using .230” seed wheel (alfalfa)
6 oz
32.00
09096921
Package of half-rate chemical ( C) metering wheel and tow spacers for 1 1/4” outlet
09072654-3
U-frame replacement for Jumbo applicators
09078765
Hopper lid lock package for attachment to existing Super or Jumbo applicator
09MLL
09178768
72.00
40.00
4 lbs
47.00
8 oz
33.00
Jumbo hopper lid and hinge only, opening for one Lock N’ Load valve
4 lbs
60.00
Suspender for placement inside hipper to keep granules suspended and create even flow of
materials around rotor bar.
2 lbs
29.00
NOVEMBER 2014
GST # R101743045
Sheet 203
09074321
JUMBO INDIVIDUAL CAM-GAUGE
APPLICATORS AND PACKAGES
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
Choice of 2, 3 or 4 openings per hopper
Hopper lid measures 13 1/2 “ x 12 3/4” (Lock n’ Load Lids Available)
Rubber rotor bar
U-frame mounting bracket with 1/2” pre-drilled holes and slots for mounting
Specifications: 45 lbs (20.5 kg) capacity hopper with snap-on stainless steel hopper bottom & slide for easy cleaning; sight window bolt-on mounting
for easy removal cam-type rate gauge; rubber rotor blade and sealed bearings.
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
1. SELECT A 45 LB CAPACITY JUMBO APPLICATOR PKG-COMPLETE WITH RUBBER
ROTOR BAR, HOSES, HOSE CLAMPS, STABILIZERS & CLAMP STRAPS
09M902EM-R
45 lb. row crop applicator package consisting of hopper with twin rubber rotor bar for heavy core
granules & two outlets, “U” frame mounting bracket, two 42” flexible tubes, stabilizers, and clamp
straps.
29 lbs
$490.00
09M903EM-R
straps.
31 lbs
527.00
09M904EM-R
straps.
33 lbs
573.00
2. Optional Drive Packages
09075589
12-Volt, 4 amp, 1/64 hp electric motor drive for use up to (2) hoppers. Complete with switch,
drive sprockets, chain and guard.
11 lbs
282.00
09082843
12-Volt, 6 amp, 1/32 hp electric motor drive for use on up (3) hoppers. Complete with switch,
drive sprockets, chain and guard.
13 lbs
491.00
09093895
Heavy-duty 12-volt, 25 amp, 1/4 hp electric motor drive for use on up to (12) hoppers. Complete
with switch, drive sprockets, chain and guard.
42 lbs
1300.00
09069286R-C1
Ground-drive, rubberl wheel. Attaches to diamond or flat tool bar. Complete with driven sprocket
and chain. Use with hopper mounts 09072649EMS & 09073649EMS. Drives up to 12 hoppers.
69 lbs
888.00
13 lbs
169.00
09176744
Hopper extension for Jumbo applicator to add 45 lbs additional capacity.
If ordered as original equipment, deduct price of 09173668/40 lid from hopper package
09177744-3
Screen for jumbo hopper extension
-8.00
2 lbs
69.00
LL
By adding the letters “LL to the end of any model row hopper, the hopper will have the lid die cut
to accept a Lock n’ Load valve. Add amount to price in price list.
09LLV
Lock n’ Load valve for attachment to row applicator
NOVEMBER 2014
23.00
101.00
GST # R101743045
Sheet 203
Cam Gauge Metering of Herbicides and insecticides
45 lb capacity of granular chemicals at density of 45 lb/cu. ft.
•
•
•
•
•
JUMBO INDIVIDUAL CAM-GAUGE
APPLICATORS & PACKAGES
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
5. OPTIONAL CONNECTOR PKG WHEN MOUNTING MULTIPLE HOPPERS IN-LINE
3 lbs
$76.00
09074323
3 lbs
88.00
Per foot
4.00
M06-875-000
.875 in ID clear flexible tubing. Order by the foot.
M11-0012-010
Mini-hose clamp, 5/8” x 1-1/4”. (secures tube to spout)
09105D
5” ro-bander
2 lbs
34.00
09107D
7” ro-bander
2 lbs
32.00
09110D
10” ro-bander
2 lbs
39.00
09114
2 lbs
73.00
09073673
Attaching bracket for single ro-bander to tool bar.
2 lbs
64.00
14 lbs
150.00
8 oz
33.00
2.00
09073649EMS
Adjustable tool bar mount (14” to 24”) fits up to 5” diamond or 7” square tool bar
09078765
Hopper lid lock package for attachment to existing Jumbo or Super applicator
09MLL
Jumbo hopper lid and hinge only, opening for one Lock n” Load valve
4 lbs
60.00
09178768
Suspender for placement inside hopper to keep granules suspended and create even flow of
materials around rotor bar
2 lbs
29.00
09072654-3
U-frame mounting bracket for Jumbo applicator
4 lbs
47.00
NOVEMBER 2014
GST # R101743045
Sheet 203
09074321
JUNIOR STEEL CAM-GAUGE
APPLICATORS PACKAGES
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
CAM GAUGE METERING OF HERBICIDES AND INSECTICIDES
• 20 lb capacity of granular ag chemicals at density of 45 lb/cu ft
Choice of 1, 2 or 3 openings per hopper
Hopper lid measures 9 x 10 3/4”
Includes rubber rotor bar
SPECIFICATIONS: 20lb (9.9 kg) capacity hopper (approximate, with clay granules), with snap-on stainless steel hopper bottom and slide for easy
cleaning; bolt-n mounting for easy removal; precision cam-type rate gauge; rubber rotor and sealed bearings.
OPTIONS: Extension to double capacity. Lock n’ Load lids, Lock n’ Load valve.
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
1. SELECT A 20 LB CAPACITY JUNIOR APPLICATOR PACKAGE
0901JR-R
20 lb row applicator consisting of hopper with rubber rotor bar and one outlet.
15 lbs
$290.00
0902JR-R
20 lb row applicator consisting of hopper with rubber rotor bar and two outlet.
15 lbs
301.00
0903JR-R
20 lb row applicator consisting of hopper with rubber rotor bar and three outlet.
16 lbs
317.00
2. CHOOSE A DRIVE PACKAGE
09075589
12-volt, 4 amp, 1/64 hp electric motor drive for use on up two hoppers. Complete with switch, drive
sprockets, chain and guard.
11 lbs
282.00
09082843
12-volt, 6 amp, 1/32 hp electric motor for use on up three hoppers. Complete with switch, drive sprockets,
chain and guard.
13 lbs
491.00
09093895
Heavy-duty 12 volt, 25 amp, 1/4 hp electric motor drive for use on up to twelve hoppers. Complete with
switch drive sprockets, chain and guard.
42 lbs
1300.00
09069286R-C1
Ground drive, steel wheel. Attaches to diamond or flat tool bar. Complete with driven sprocket and chain.
Use with hopper mounts #09072649EMS and #09073649EMS. Drives up to 12 hoppers.
69 lbs
888.00
10 lbs
123.00
3. OPTIONAL HOPPER EXTENSION TO INCREASE CAPACITY
09070535
Hopper extension for Junior applicator to add 22 lbs additional capacity.
If ordered as original equipment, deduct price of #09074142/50 lid from hopper package
-8.00
LL
By adding the letters LL to the end of any model row hopper, the hopper will have the lid die cut to accept
a Lock n’ Load valve. Ad amount to price in price list.
09LLV
Lock n’ Load valve for attachment to row applicator.
23.00
101.00
09074321
3 lbs
76.00
09074323
3 lbs
88.00
NOVEMBER 2014
GST # R101743045
Sheet 203
•
•
•
JUNIOR STEEL CAM-GAUGE
APPLICATORS PACKAGES
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
M06-875-000
.875 in ID clear flexible tubing. Order by the foot.
M11-0012-010
Mini-hose clamp, 5/8” x 1-1/4”. (secures tube to spout)
09105D
5” ro-bander
Per Foot
$4.00
2.00
2 lbs
34.00
09107D
7” ro-bander
2 lbs
32.00
09110D
10” ro-bander
2 lbs
39.00
09114
2 lbs
73.00
09073673
Attaching bracket for single ro-bander to tool bar.
2 lbs
64.00
09073649EMS
Adjustable too bar mount (14” to 24”) fits up to a 5” diamond or 7” square tool bar
14 lbs
150.00
09072624-3
U-frame replacement for super or junior applicators.
4 lbs
47.00
NOVEMBER 2014
GST # R101743045
Sheet 203
PART
NUMBER
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
INDIVIDUAL ITEMS FOR APPLICATORS
09074321 ................................. $76.00
09178768 .............................. $ 29.00
CONNECTOR DRIVE TUBE
Use for up to 42” hopper spacing.
SUSPENDER, Jumbo hopper
Weight 2 lbs.
Weight 3 lbs.
09073649EMS .................. $ 146.00
09074323 ................................ $ 88.00
TOOL BAR MOUNTING
Adjustable 14” to 24” high. Fits up to 5” diamond
or 7” square tool bar.
Weight 14 lbs.
CONNECTOR DRIVE TUBE
Use for up to 80” hopper spacing.
Weight 3 lbs.
NOVEMBER 2014
SUSPENDER, Super hopper
GST # R101743045
Sheet 203
DRIVES FOR ROW CROP
CAM GAUDE APPLICATORS
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
DESCRIPTION
WGT
09075589
12-VOLT ELECTRIC MOTOR DRIVE -complete with switch, drive speakers, chain and guard.
4 amp. 1/64 HP. Use on two hoppers. Silver or black color
11 lbs
$282.00
09075589-4SM
12-VOLT SERVICE MOTOR -with mount
5 lbs
229.00
09075589-4
12-VOLT ELECTRIC MOTOR only
4 lbs
198.00
09082843
12-VOLT ELECTRIC MOTOR DRIVE -complete with switch, sprockets, chain and guard.
6 amp, 1/32 HP for use with up to three hoppers. Not for use on PDM or PDA applicators.
13 lbs
491.00
09082842-4
12-VOLT SERVICE MOTOR -only with drive sprocket.
6 lbs
342.00
09093895
HEAVY DUTY ELECTRIC MOTOR DRIVE -Complete with switch and drive parts. May be
used in place of hydraulic. 25 amp, 1/4 HP for up to 12 hoppers
42 lbs
1300.00
L01-0012-007
HEAVY DUTY ELECTRIC MOTOR only.
9 lbs
615.00
09074678
HYDRAULIC MOTOR DRIVE -Complete with Flo-Control valve, drive sprockets, chain and
bracket.
24 lbs
1050.00
09076679-C1
HYDRAULIC C7K MOTOR -With 09076691 Flo-Control.
19 lbs
783.00
09069286R-C1
GROUND DRIVE, RUBBER TIRE– attaches to diamond or flat tool bar. Complete with driven
sprocket and chain. Use with hipper mounts 09072649EMS and 09073649EMS
69 lbs
888.00
NOVEMBER 2014
LIST PRICE
FRT EXTRA
GST # R101743045
Sheet 203
PART
NUMBER
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
09105D ................................... $34.00
5 INCH RO-BANDER
Weight 2 lbs.
09107D .................................. $32.00
7 INCH RO-BANDER
Weight 2 lbs
09W1 .................................... $125.00
DRIVE PACKAGE 5 to 1 ratio. Same as
above with one pair 3/4R insert only. Use
with line shaft (50 - 100 RPM) available f
m planter.
Weight 5 lbs
09110D ................................... $39.00
10 INCH RO-BANDER
Weight 2 lb
09069507P ............................ $93.00
RESILIENT RUBBER ROTOR, 3 inch
for single outlet. Super or Junior applicator.
Use with heavy-core granules.
Includes washers.
Weight 2 lb.
09114 ..................................... $73.00
09076719P ............................. $90.00
TWIN RESILIENT RUBBER ROTOR for
two outlet Super or Junior
applicator. Use with heavy core
granules. Includes washer
Weight 2 lbs.
M10-2539-200 ........................ $53.00
WYE CONNECTOR for use on two outlets
or to combine chemicals from two hoppers
to one tube.
Weight 1 lb
*09069508P ............................. $90.00
RESILIENT RUBBER ROTOR, 8”, for Super
or Junior applicators. Use with heavy core
granules. Includes
washers.
Weight 2 lbs.
09176744 ............................... $169.00
HOPPER EXTENSION FOR Jumbo applicator
Weight 12 lb.
09177744-3
SCREEN ................................ $69.00
for above
Weight 2 lb.
*09076719-C1P ........................ $98.00
TWIN RESILIENT RUBBER ROTOR, for
two outlet Jumbo applicator. Use with heavy
core granules (16 3/4" shaft). Includes washers.
Weight 2 lb.
09070535 .............................. $123.00
HOPPER EXTENSION for Junior applicator.
Weight 10 lbs.
*09070534P .......................... $89.00
RESILIENT RUBBER ROTOR, 10” for
Jumbo applicator. Use with heavy core
granules (16-3/4" shaft).
Includes washers.
Weight 2 lb.
09093896 .............................. $169.00
HOPPER EXTENSION for Super applicator.
Weight 11 lbs
NOVEMBER 2014
ACCESSORIES FOR APPLICATORS
09072624-3 ........................... $26.00
“U” FRAME or Super or Junior
applicators
09072645-3 ........................... $47.00
“U”FRAME for Jumbo applicators
Weight 4 lbs.
14 INCH RO-BANDER complete with
mounting brackets
Weight 2 lb.
GST # R101743045
Sheet 203
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
•
•
•
•
•
•
•
•
1200 gallon tank & frame
Powder coat paint
Top operated tank drain
Drawbar with swivel hitch
Remote sight gauge
Clean water dispenser (4.5 gal)
3” Main & 2” rinse tank quick fill
Inline boom filters
NOVEMBER 2014
GST # R101743045
Sheet 203
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
NOVEMBER 2014
GST # R101743045
Sheet 203
POLY FORAGE PRESERVITIVE
APPLICATOR PACKAGES
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
Cam Gauge Metering of Forage Preservatives
• 2.3 cu ft capacity polyethylene hopper
Approx. 100 lb capacity at 45 lb per cu ft density
Cam gauge metering, 2, 3 or 4 outlets
U-frame mounting bracket with 1/2” holes and slots included
Tubing and hose clamps are optional
Note: Gandy Company does not supply rate charts for these additive or preservative products. Purchaser must consult the manufacturer
for suggested rates and perform a field calibration check.
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
43 lbs
$1,054.00
1. SELECT POLY FORAGE PRESERVATIVE APPLICATOR
09PC04WP12
100 lbs capacity hopper with four-outlets on stainless steel bottom and slide, straight spouts, 8” rubber
rotor, “U” frame mounting bracket and two spout caps. 1/64 hp 12 volts motor assembled in place
2. SELECT DROP TUBE AND SPRING CLIPS
2406224-12
Plastic drop tube, 12 inches
1 lbs
5.00
2406224-108
Plastic drop tube, 9 ft
3 lbs
30.00
E09-06137
Spring clip to fasten tubing to spouts
1 oz
1.00
09099948
Mounting for forage preservative applicator, hitch placement on round balers
145.00
09072661
110-Volt replacement motor drive, complete
795.00
09075589-4
12-volt, 4 amp, 1/64 hp replacement motor only
09099923-2
Bottom and slide with two openings. Spouts angled toward cam gauge.
126.00
09099926-2C1
Bottom and slide with two openings. Straight spouts.
126.00
09099926-2C2
Bottom and slide with two openings. Spouts angles away cam gauge
126.00
4 lbs
198.00
09099926-3
Bottom and slide with three openings. Spouts angles toward cam gauge
133.00
09099926-3C1
Bottom and slide with three openings. Straight spouts
133.00
09099926-3C2
Bottom and slide with three openings. Spouts angles away from cam gauge
133.00
09099926-4
Bottom and slide with four openings. Spouts angles toward cam gauge
145.00
09099926-4C1
Bottom and slide with four openings. Straight spouts
145.00
09099926-4C2
Bottom and slide with four openings. Spouts angles away from cam gauge
145.00
0906375
Cam gauge
09076719PC
Twin rubber rotor replacement pkg for two-outlet hopper. Use with heavy-core granules. Includes
washers & O-rings.
89.00
09069508PC
Rubber 8” rotor bar replacement pkg. Includes washers, O-rings & spacers.
93.00
0908012-6
Replacement straight spout
6.00
09073636-6
Replacement angled spout
7.00
NOVEMBER 2014
6.00
GST # R101743045
Sheet 203
•
•
•
•
JUMBO STEEL FORAGE ADDITIVE
APPLICATOR PACKAGES
www.gandy.net
TAB# 19 SPREADERS
US PRODUCT
Note: Gandy Company does not supply rate charts for these additive or preservative products. Purchaser must consult the manufacturer for suggested rates
and perform a field calibration check. Mounting locations vary on implements and user may be required to fabricate mounting brackets.
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
1. SELECT A 45 LB CAPACITY JUMBO APPLICATOR
09M902WP12
45 lb capacity Jumbo hopper with two-outlet stainless steel bottom and slide, straight spout, an 10”
rubber rotor, “U” frame mounting bracket and two spout caps. 1 6/4 hp 12-volt motor assembled.
41 lbs
$691.00
09M903WP12
45 lb capacity Jumbo hopper with three-outlet stainless steel bottom and slide, straight spout, an 10”
rubber rotor, “U” frame mounting bracket, and two spout caps. 1 6/4 hp 12-volt motor assembled.
42 lbs
698.00
09M904WP12
45 lb capacity Jumbo hopper with four-outlet stainless steel bottom and slide, straight spout, an 10”
rubber rotor, “U” frame mounting bracket, and two spout caps. 1 6/4 hp 12-volt motor assembled.
43 lbs
720.00
10 lbs
169.00
2. OPTIONAL HOPPER EXTENSION TO INCREASE CAPACITY
09176744
Hopper extension for Junior applicator to add 11 cu ft or approx 45 lbs additional capacity
If ordered as original equipment, deduct price of #09173668/40 lid for hopper pkg
-8.00
3. SELECT DROP TUBE AND SPRING CLIPS
2406224-12
Plastic drop tube, 12 inches
5.00
2406224-108
Plastic drop tube, 9 ft
30.00
E09-06137
Spring clip to fasten tubing to spouts
09177744-3
1 oz
1.00
Screen for Jumbo hopper
4 lbs
69.00
M10-0005-011
Rain cover for Jumbo hopper with 12-volt electric motor
2 lbs
57.00
09072661
110-volt replacement motor drive, complete
09075589-4
12-volt, 4 amp, 1/64 hp replacement motor only
09173669-2
Bottom and slide with two openings. Spouts angled toward cam gauge.
99.00
09173669-2C1
Bottom and slide with two opening. Straight spout
99.00
09173669-2C2
Bottom and slide with two opening. Spout angled away from cam gauge
99.00
09173669-3
Bottom and slide with three openings. Spouts angled toward cam gauge
106.00
09173669-3C1
Bottom and slide with three opening. Straight spout
106.00
09173669-3C2
Bottom and slide with three opening. Spout angled away from cam gauge
106.00
09173669-4
Bottom and slide with four openings. Spouts angled toward cam gauge
113.00
09173669-4C1
Bottom and slide with four openings. Straight spouts
113.00
09173669-4C2
Bottom and slide with four openings. Spouts angled away cam gauge
113.00
0906375
Cam gauge
09076719-C1P
Twin rubber rotor replacement package. Includes washers, O-rings and bushings.
09070534P
10-inch rubber rotor replacement package. Includes washers and O-rings.
89.00
0908012-6
Replacement individual straight spout.
6.00
09073636-6
Replacement individual angled spout
7.00
NOVEMBER 2014
795.00
4 lbs
198.00
6.00
2 lbs
98.00
GST # R101743045
Sheet 203
Cam Gauge Metering of Forage Preservatives
• 45 lb capacity
• 1/64 hp 12 volt electric motor drive
• Steel applicators with cam gauge metering
• U-frame mounting bracket with 1/2” holes and slots included
• Optional extensions to double capacity can be ordered for factory
installation at time of order
ADJUSTABLE SLOTTED BOTTOM
HOPPER
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
•
•
•
•
U-frame mounting bracket with 1/2” pre-drilled holes and slots
Special versions suitable for talcum powder application
Adjustable slotted bottom gives application across the hopper’s 14” width
Developed for application of humus or peat-based inoculants in the field or at seed
production facilities
Note: Testing of material is always recommended for materials of uncertain flow characteristics. Rates can be adjusted by cam gauge, but unit is not
recommended for critical or fine rates.
SPECIFICATIONS: 2.3 cu. ft. polyethylene hopper, lid with latches, three internal agitators, slotted bottom adjusted for size with cam gauge to meter
material the width of the hopper. U-frame bracket with 1/2” holes and slots for mounting is included.
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
1. SELECT HUMUS OR PEAT-BASED INOCULANT APPLICATOR BELOW
09099937
Adjustable slotted bottom poly applicator for humus or peat based inoculants. Includes 110 volt motor
75 lbs
$1,746.00
CHOOSE TALC APPLICATOR BELOW:
09008961
Adjustable slotted bottom poly applicator for talc. Includes 12 volt motor
75 lbs
1,293.00
09008962
Adjustable slotted bottom poly applicator for talc. Includes 110 volt motor
75 lbs
1,701.00
2. WEAR PARTS
09099946
Latch package for poly hopper lid (replacement)
M05-0000-008 Rubber replacement latch only, 4”
NOVEMBER 2014
42.00
20.00
GST # R101743045
Sheet 203
Developed for Humus, Peat-Based Inoculants and Talc
• 2.3 cu. ft. capacity poly hopper
10T SERIES SPREADERS
6,8,10,12 FT Tractor Tow Hitch
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
Specifications:
Capacity:
Bottom/Slide:
Overall Height:
Overall Length:
Clearance:
Rims:
Tires:
1.5 cubic feet per ft. of hopper length; approx 100 lbs/ft
Diamond-shaped openings 1-1/2” long, spaced 4” apart
36”
90”
13” above ground; approx 6” with spread plate
15 x 5K 6-bolt rims included; 15 x 10k rims optional for floatation tires
Optional
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
1. CHOOSE A SPREADER
1006T
6-foot Spreader. Approx. hopper capacity, 600 pounds. 9 cu ft. Wheel tread 86” (with wheels “dished in”).
Overall width, 99”. 18 openings
515 lbs
$4,524.00
1008T
8-foot Spreader. Approx. hopper capacity, 800 pounds. 12 cu ft. Wheel tread 110” (with wheels “dished
in”). Overall width, 123”. 24 openings
598 lbs
4,905.00
1010T
10-foot Spreader. Approx. hopper capacity, 1,000 pounds. 15 cu ft. Wheel tread 134” (with wheels “dished
648 lbs
5,366.00
1012T
12-foot Spreader. Approx. hopper capacity, 1,200 pounds. 18 cu ft. Wheel tread 158” (with wheels “dished
753 lbs
5,844.00
2. CONVERT HAND LEVER SHUTOFF TO OPTIONAL HYDRAULIC OR ELECTRIC SHUTOFF
3209743A
0101104
Hydraulic shutoff cylinder and mounting in lieu of hand lever. Factory installed. (user supplies 1/4” hydraulic hoses from tractor to shutoff cylinder and 1/4” NPT fittings)
5 lbs
Electric actuator shutoff and mounting in lieu of hand lever. Factory installed
271.00
831.00
3. LOW SPEED BEARING BEARINGS INCLUDED IN BASE; OPTIONAL HIGH-SPEED BEARING
BELOW
0102105
Heavy-duty hub/axle for road speeds
010207
Deduct std. hub & axle when ordering HD hub and axle
927.00
NET
-643.50
30 lbs
126.00
R01-0015-020 Deduct 2 15 x 5K rims when ordering #R01-0015-030
NET
-82.50
NOVEMBER 2014
GST # R101743045
Sheet 203
4. 15 X 5K 6-BOLT RIMS INCLUDED IN BASE PRICE; OPTIONAL 15 X 10K BELOW
R01-0015-030 Rim only 15 x 10K (for high-floatation tire-No. 11L15) two required
Standard Equipment:
• Hot rolled steel removable hopper bottom and hinged rate-control slide
• Shur-feed rotors; hand-removable stub drive for rotor
• Adjustable spread plate
• Hand lever shutoff standard (optional hydraulic or electric available)
• Weather-tight removable and reversible covers with spill-guards and dual lock-down
latches for each cover
• 15 x 5k 6 rims standard
• Powder angles included
• Low speed bearings standard; high-speed bearings for road speeds optional
• Heavy-duty tractor hitch with extension at rear for trailing non-ground engaging machines
• Operators manual and rate charts included
10T SERIES SPREADERS
6,8,10,12 FT Tractor Tow Hitch
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
R02-0015-010
6.75 x 15, 4 ply rib implement tubeless tire. Uses standard 15 x 5K rims included in base. Order two
tires per spreader
18 lbs
$178.00 ea
R02-0015-020
11L115, 6 ply tubeless tire. Requires R01-0015-030 rim. Order tow tires per spreader.
30 lbs
207.00 ea
0185214
Calibration pan, 4 ft for 8 ft spreader (order 2 per unit)
6 lbs
76.00
01105214
8 lbs
79.00
01125214
11 lbs
82.00
0108013
Clamp on hole closure
0108190
Deflectors, side-dressing or banding
0101103
Electric actuator shutoff
935.00
3209743
Hydraulic cylinder & mounting as an extra when hopper has hand lever in place
441.00
3209742
Hydraulic cylinder only
5 lbs
351.00
Hydraulic cylinder repair kit
5 lbs
48.00
3209742R
0197102
14.00
3 lbs
Manual holder pkg option for units not so equipped
78.00
48.00
0566394-T
Powder angle pkg for 6ft “T” series standard equipment, as an extra
2 lbs
89.00
0586394-T
2.5 lbs
107.00
05106394-T
3 lbs
115.00
05127694-T
3.5 lbs
125.00
1 lbs
20.00
5708210
RETROFIT KITS
Spout holder pkg, centered angle spout only, order one per outlet
Conversion pkg to T-series for discontinued spreaders are listed below. To ensure correct rate chart
usage, please note that: current production Model 10T series has 1-1/2” openings spaced 4” apart 10 series has 2” openings spaced 6” apart - 10A series has 1-1/2” openings spaced 3-3/8” apart - 10S
series has 1-1/2” openings spaced 6” apart
0568011&12PKG
Retrofit 10T bottom, slide & rotor pkg, 6ft for discontinued 1006 & 1006A models
103 lbs
1,043.00
0588011&12PKG
122 lbs
1,207.00
05108011&12PKG Retrofit 10T bottom, slide & rotor pkg, 10ft for discontinued 1010 & 1010A models
142 lbs
1,404.00
164 lbs
1,599.00
NOVEMBER 2014
GST # R101743045
Sheet 203
5. 10T SERIES SHIPS WITHOUT TIRES - OPTIONAL TIRES LISTED BELOW
10TR SERIES SPREADERS
TAB# 19 SPREADERS
US PRODUCT
6,8,10,12ft 3 POINT HITCH, END-WHEEL DRIVE WITH HYDRAULIC
SHUTOFF & STAND
www.gandy.net
Specifications:
Capacity:
Bottom/Slide:
Overall Height:
Overall Length:
Clearance:
Rims:
Tires:
36”
90”
15 x 5K 6-bolt rims included; 15 x 10k rims optional for floatation tires
Rims can be “dished-out” for 5-inch wider wheel spacing
Optional
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
1006TR
6-foot Spreader. Cat ll 3 pt hitch. Hydraulic shut off (hyd hoses not included user supplies 1/4”
hoses and 1/4” NPT fitting) Parking stand. Approximately hopper capacity, 600 pounds 9 cu ft.
Wheel tread 87” (with wheels “dished in”). Overall width 100”. 18 openings
613 lbs
$5,820.00
1008TR
hoses and 1/4” NPT fitting) Parking stand. Approximately hopper capacity, 800 pounds 12 cu ft.
703 lbs
6,108.00
1010TR
hoses and 1/4” NPT fitting) Parking stand. Approximately hopper capacity, 1,000 pounds 15 cu ft.
802 lbs
6,396.00
1012TR
hoses and 1/4” NPT fitting) Parking stand. Approximately hopper capacity, 1,200 pounds 18 cu ft.
903 lbs
6,683.00
R02-0015-010 6.75 x 15, 4 ply rib implement tubeless tire. Uses standard 15 x 5K rims included in base. Order
two tires per spreader
18 lbs
178.00
R02-0015-020 11L115, 6 ply tubeless tire. Requires R01-0015-030 rim. Order tow tires per spreader.
30 lbs
207.00
2. 10TR SERIES SHIPS WITHOUT TIRES—OPTIONAL TIRES LISTED BELOW
NOVEMBER 2014
GST # R101743045
Sheet 203
Standard Equipment:
• Cat ll, 3 pt hitch 10TR series
• Hydraulic shutoff (user supplies 1/4” hyd hoses and 1/4” NPT fitting)
• Parking stand
• End wheel drive turns rotor in each side
• Powder angles and adjustable spread plate
• Weather-tight removable and reversible covers with spill-guards and dual lockdown latches for each cover
• Low speed bearings standard; high-speed bearings for road speeds optional
10TR SERIES SPREADERS
TAB# 19 SPREADERS
US PRODUCT
6,8,10,12ft 3 POINT HITCH, END-WHEEL DRIVE WITH HYDRAULIC
SHUTOFF & STAND
www.gandy.net
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
0185214
6 lbs
$76.00
01105214
8 lbs
79.00
01125214
11 lbs
82.00
0108013
0108190
3209743
Hydraulic cylinder & mounting as an extra when hopper has hand lever in place
3209742
5 lbs
351.00
5 lbs
48.00
3209742R
0197102
14.00
3 lbs
78.00
441.00
48.00
0566394-T
2 lbs
89.00
0586394-T
2.5 lbs
107.00
05106394-T
3 lbs
115.00
05127694-T
3.5 lbs
125.00
1 lbs
20.00
5708210
RETROFIT KITS
0568011&12PKG
103 lbs
1,043.00
0588011&12PKG
122 lbs
1,207.00
142 lbs
1,404.00
164 lbs
1,599.00
NOVEMBER 2014
GST # R101743045
Sheet 203
PART
NUMBER
TAB# 19 SPREADERS
US PRODUCT
10T-PTH SERIES SPREADERS
www.gandy.net
6,8,10,12 ft Spreaders with 3 pt Hitch & Hydraulic Shutoff
Specifications:
Capacity:
Bottom/Slide:
Overall Height:
Overall Length:
Clearance:
36”
90”
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
1006T-PTH
6-foot Spreader. Bottom with 1-1/2” holes spaced 4” apart, powder angles, mounting brackets, parking stand and *hydraulic shutoff. Approximately hopper capacity, 600 pounds 9 cu ft. 18 openings
613 lbs
$4,924.00
1008T-PTH
8-foot Spreader. Bottom with 1-1/2” holes spaced 4” apart, powder angles, mounting brackets, parking stand and *hydraulic shutoff. Approximately hopper capacity, 800 pounds 12 cu ft. 24 openings
703 lbs
5,247.00
1010T-PTH
10-foot Spreader. Bottom with 1-1/2” holes spaced 4” apart, powder angles, mounting brackets, parking stand and *hydraulic shutoff. Approximately hopper capacity, 1,000 pounds 15 cu ft. 30 openings
802 lbs
5,690.00
1012T-PTH
12-foot Spreader. Bottom with 1-1/2” holes spaced 4” apart, powder angles, mounting brackets, parking stand and *hydraulic shutoff. Approximately hopper capacity, 1,200 pounds 18 cu ft. 36 openings
903 lbs
5,977.00
2. CHOOSE A HYDRAULIC OR ELECTRIC DRIVE PACKAGE
57082100
*Hydraulic drive pkg, less hoses, 15 gal flow (*user supplies 1/2” hydraulic hoses from tractor to drive
and 1/2” NPT fittings)
22 lbs
890.00
57094108
Electric drive pkg, 12V, 11-13 amps
54 lbs
1,427.00
NOVEMBER 2014
GST # R101743045
Sheet 203
Standard Equipment:
• 3 pt hitch
• Parking stand
• Powder angles and adjustable spread plate included
• Weather-tight removable and reversible covers with spill-guards and dual
lock-down latches for each cover
• Hydraulic shutoff (user supplies 1/4” hyd hoses and 1/4” NPT fitting)
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
0185214
6 lbs
$76.00
01105214
8 lbs
79.00
01125214
11 lbs
82.00
0108013
0108190
0101103
3209742
5 lbs
351.00
3209742R
5 lbs
48.00
57082105
Hydraulic hose pkg-connects hydraulic shutoff cylinder to hydraulic drive motor
5 lbs
245.00
0197102
14.00
3 lbs
78.00
935.00
48.00
0566394-T
2 lbs
89.00
0586394-T
2.5 lbs
107.00
05106394-T
3 lbs
115.00
05127694-T
3.5 lbs
125.00
1 lbs
20.00
5708210
RETROFIT KITS
0568011&12PKG
103 lbs
1,043.00
0588011&12PKG
122 lbs
1,207.00
142 lbs
1,404.00
164 lbs
1,599.00
NOVEMBER 2014
GST # R101743045
Sheet 203
PART
NUMBER
TAB# 19 SPREADERS
US PRODUCT
10T-TBM SERIES SPREADERS
www.gandy.net
6,8,10,12 ft Spreaders for Implement Mount
Specifications:
Capacity:
Bottom/Slide:
Overall Height:
Overall Length:
Clearance:
36”
90”
PART
NUMBER
DESCRIPTION
WGT
1006T-TBM
6-foot Spreader. Bottom with 1-1/2” holes spaced 4” apart with 18 outlets. Powder angles and mounting brackets. Approximately hopper capacity, 600 pounds 9 cu ft
613 lbs
$3,561.00
1008T-TBM
8-foot Spreader. Bottom with 1-1/2” holes spaced 4” apart with 24 outlets. Powder angles and mounting brackets. Approximately hopper capacity, 800 pounds 12 cu ft.
703 lbs
3,843.00
1010T-TBM
10-foot Spreader. Bottom with 1-1/2” holes spaced 4” apart with 30 outlets. Powder angles and
mounting brackets. Approximately hopper capacity, 1,000 pounds 15 cu ft.
802 lbs
4,134.00
1012T-TBM
12-foot Spreader. Bottom with 1-1/2” holes spaced 4” apart with 36 outlets. Powder angles and
mounting brackets. Approximately hopper capacity, 1,200 pounds 18 cu ft.
903 lbs
4,422.00
LIST PRICE
FRT EXTRA
2. SELECT ONE: HAND LEVER, HYDRAULIC OR ELECTRIC SHUTOFF-FACTORY INSTALLED
3408236
Hand lever shutoff
7 lbs
84.00
3209742
*Hydraulic cylinder shutoff
6+ lbs
351.00
0101103
Electric shutoff
935.00
3. OPTIONAL MOUNTING LEG PACKAGE
57082102
Mounting leg pkg of 2 of 5” x 7” implement tool bar, straight
76 lbs
297.00
57082104
Mounting leg pkg of 2 of 5” x 7” implement tool bar, offset
69 lbs
297.00
5708424
Mounting leg pkg of 21 for center leg of 10ft, or longer span
18 lbs
160.00
NOVEMBER 2014
GST # R101743045
Sheet 203
Standard Equipment:
• Implement mount
• Powder angles and adjustable spread plate included
• Weather-tight removable and reversible covers with spill-guards and dual
lock-down latches for each cover
• Electric or hydraulic drive
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
4. OPTIONAL TOOL BAR
5768330
6 ft tool bar
90 lbs
$300.00
5788660
8 ft tool bar
120 lbs
340.00
57108330
10 ft tool bar
150 lbs
443.00
57128330
12 ft tool bar
180 lbs
493.00
5. CHOOSE A HDRAULIC OR ELECTRIC DRIVE PACKAGE
57082100
*Hydraulic drive pkg., less hoses, 15 gallon flow (user supplies 1/2” hyd hoses from tractor to drive &
1/2” NPT fitting)
22 lbs
890.00
57094108
Electric drive pkg, 12V, 11-13 amps
54 lbs
1,427.00
0185214
6 lbs
76.00
01105214
8 lbs
79.00
01125214
11 lbs
82.00
0108013
0108190
0101103
3209742
5 lbs
351.00
3209742R
5 lbs
48.00
57082105
Hydraulic hose pkg-connects hydraulic shutoff cylinder to hydraulic drive motor
5 lbs
245.00
0197102
14.00
3 lbs
78.00
935.00
48.00
0566394-T
2 lbs
89.00
0586394-T
2.5 lbs
107.00
05106394-T
3 lbs
115.00
05127694-T
3.5 lbs
125.00
1 lbs
20.00
5708210
RETROFIT KITS
0568011&12PKG
103 lbs
1,043.00
0588011&12PKG
122 lbs
1,207.00
142 lbs
1,404.00
164 lbs
1,599.00
NOVEMBER 2014
GST # R101743045
Sheet 203
PART
NUMBER
6500 SERIES SPREADERS
TAB# 19 SPREADERS
US PRODUCT
4,5 & 6 ft Drop Spreader With Tractor Tow Hitch
Spreads Fertilizer, Granular Chemicals, Lime & Seed
www.gandy.net
Standard Equipment:
Precision-mated bottom & slide of cold milled steel
• Adjustable angle spread plate
• Optional jigglers to aid flow of material
• Choice of 16”, 18”, 20” & 26” tires
• Polyester powder-coated baked-n finish, green
•
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
1. CHOOSE A DROP SPREADER
6504T16
4 ft spreader with tractor hitch, hand-lever shutoff and 16” pneumatic tires on steel rim. Approx 260 lbs of
capacity
230 lbs
$1,807.00
6504T18
4 ft spreader with tractor hitch, hand-lever shutoff and 18” high floatation pneumatic tires on steel rim. Approx
260 lbs of capacity
234 lbs
1,938.00
6505T16
capacity
273 lbs
1,873.00
6505T18
325 lbs of capacity
277 lbs
2,002.00
6506T16
capacity
288 lbs
1,938.00
6506T18
390 lbs of capacity
313 lbs
2,068.00
31 lbs
455.00
2. OPTIONAL FACTORY INSTALLED HYDRAULIC OR ELECTRIC SHUT OFF
659711
Hydraulic shut-off attachment in lieu of hand lever (factory installed-hydraulic hoses not included) (user supplies 1/4” hydraulic hoses from tractor to shutoff cylinder & 1/4” NPT fittings)
6522
Electric shutoff attachment, ordered in lieu of hand shutoff ( factory installed)
930.00
6521
Electric actuator shut-off attachment, retrofit
6 lbs
981.00
069242
Tractor hitch bundle with lever shut-off
17 lbs
243.00
0107813
Bolt-on hole closures, one per opening.
0107890
Deflectors for side dressing or bending.
4 oz
77.00
0185214
4-ft. calibration pan
1 lb
76.00
01105214
5-ft. calibration pan.
6 lbs
79.00
01125214
7 lbs
82.00
657
Jiggler package, 4-ft.
8 lbs
140.00
658
8 lbs
159.00
659
9 lbs
178.00
NOVEMBER 2014
17.00
GST # R101743045
Sheet 203
Specifications:
Tires: Choice of 16” pneumatic tires with steel rim, 18” high-flotation pneumatic tires with steel rim, or 20 or 26” diameter semi-pneumatic tires on steel
disc rims.
Capacities: 4-ft., 4 cubic foot (113 dm3) or approx. 260 lbs. (116 kg); 5-ft., 5 cubic foot (142 dm3 ) or approx. 325 lbs. (145 kg); 6-ft, 6 cu ft (170 dm³) or
approx 390 lbs (174 kg)
6504 Wheel Spacing: 16” tires=51”, 18” tires=58-1/2”, 20 & 26” tires=53-1/2”:
6504 Overall Width: 16” tires=59”, 18” tires=66”, 20 & 26” tires=58-1/4”
4,5 & 6 ft Drop Spreader With TractorTow Hitch
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
65A16
65A18
65A20
65A26
6518-4
R01-0015-020
R02-0015-010
654-5
DESCRIPTION
4. REPLACEMENT TIRE PACKAGES, HUB & RIM
16” Wheel Package of two: Steel hub and rims, pneumatic tire
18” Wheel package of two: Steel hub and rims, 1” bore with 18 x 8.5 x 8 4-ply tubeless pneumatic tires (standard on 6-ft. spreader).
20” Wheel package of two: Steel hub and rims with 1-3/4” wide semi-pneumatic tires for higher
clearance.
26” Wheel package of two: Steel hub and rims with 2” wide semi-pneumatic tires for higher
clearance.
Hub to adapt 15 x 15K rim for 6.70 x 15 tire for 6500 Series spreader. 2 required
Rim only, 15 x 5K for 6.70 x 15 tire for greater clearance
Tire only, 6.70 x 15, 4-ply rib tubeless for greater clearance. Order (2) per spreader
5. WEAR PARTS
Bearing, end & center
NOVEMBER 2014
WGT
LIST PRICE
FRT EXTRA
15 lbs
42 lbs
$241.00
447.00
26 lbs
320.00
50 lbs
429.00
6 lbs
19 lbs
18 lbs
213.00
85.00
178.00
2 lbs
60.00
GST # R101743045
Sheet 203
PART
NUMBER
TAB# 19 SPREADERS
US PRODUCT
5 & 6 ft Drop Spreader With 3PT Hitch End Wheel Drive System
www.gandy.net
Specifications:
Tires: Choice of 16” pneumatic tires with steel rim, 18” high-flotation pneumatic tires with steel rim, or 20 or 26” diameter semi-pneumatic tires on steel
disc rims.
Hole Size: 1” openings on all spreaders. 25 openings spaced 2.260” (5.7cm) on 5ft model; 30 openings spaced 2.188” (5.5cm) on 6 ft.
Capacities: 5-ft., 5 cubic foot (142 dm3 ) or approx. 325 lbs. (145 kg); 6-ft, 6 cu ft (170 dm³) or approx 390 lbs (174 kg)
Ground Clearance: 16” tires=6”; 18” tires=7”; 20” tires=8”; 26” tires=11” (for greater ground clearance 6.75 x 15 tires can be ordered)
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
6505TR16
5 ft spreader with tractor hitch, end-wheel drive, 16” pneumatic tires on steel rim.
361 lbs
$2,451.00
6505TR18
5 ft spreader with tractor hitch, end-wheel drive, 18” high floatation pneumatic tires on steel rim.
386 lbs
2,579.00
6506TR16
6 ft spreader with tractor hitch, end-wheel drive, 16” pneumatic tires on steel rim.
381 lbs
2,579.00
6506TR18
6 ft spreader with tractor hitch, end-wheel drive, 18” high floatation pneumatic tires on steel rim.
406 lbs
2,610.00
659711
Hydraulic shut-off attachment in lieu of hand lever (factory installed-hydraulic hoses not included) (user supplies 1/4” hydraulic hoses from tractor to shutoff cylinder & 1/4” NPT fittings)
31 lbs
455.00
6522
Electric actuator shut-off attachment, retrofit.
Hydraulic shutoff attachment
4. REPLACEMENT TIRE PACKAGES, HUB & RIM
2. OPTIONAL FACTORY INSTALLED HYDRAULIC OR ELECTRIC SHUTOFF
0107813
0107890
0185214
01105214
01125214
6521
659711
657
658
659
65A16
65A18
65A20
65A26
6518-4
R01-0015-020
R02-0015-010
654-5
16” Wheel Package of two: Steel hub and rims, pneumatic tire
18” Wheel package of two: Steel hub and rims, 1” bore with 18 x 8.5 x 8 4-ply tubeless pneumatic tires (standard on 6-ft. spreader).
20” Wheel package of two: Steel hub and rims with 1-3/4” wide semi-pneumatic tires for higher
clearance.
26” Wheel package of two: Steel hub and rims with 2” wide semi-pneumatic tires for higher
clearance.
Hub to adapt 15 x 15K rim for 6.70 x 15 tire for 6500 Series spreader. 2 required
Tire only, 6.70 x 15, 4-ply rib tubeless for greater clearance. Order (2) per spreader
5. WEAR PARTS
NOVEMBER 2014
930.00
4 oz
1 lbs
6 lbs
7 lbs
6 lbs
31 lbs
8 lbs
8 lbs
9 lbs
17.00
77.00
76.00
79.00
82.00
981.00
455.00
140.00
159.00
178.00
15 lbs
42 lbs
241.00
447.00
26 lbs
320.00
50 lbs
429.00
6 lbs
19 lbs
18 lbs
213.00
85.00
178.00
2 lbs
60.00
GST # R101743045
Sheet 203
Standard Equipment:
• Parking stand
• Precision-mated bottom & slide of cold milled steel
• Choice of 16”, 18”, 20” & 26” tires
4,5 & 6 ft Drop Spreader With 3PT Hitch
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
Specifications:
Hole Size: 1” openings on all spreaders. 25 openings spaced 2.260” (5.7cm) on 5ft model; 30 openings spaced 2.188” (5.5cm) on 6 ft.
Capacities: 4 ft, 4 cu ft (113 dm³) or approx 260 lbs (116 kg); 5-ft., 5 cubic foot (142 dm3 ) or approx. 325 lbs. (145 kg); 6-ft, 6 cu ft (170 dm³) or
approx 390 lbs (174 kg)
6504 Overall Width: 16” tires=59”, 18” tires=66”, 20 & 26” tires=58 1/4”:
PART
NUMBER
DESCRIPTION
WGT
LIST
PRICE
FRT
EXTRA
65044PTH
4 ft spreader with 3 pt hitch and hand-lever shutoff. Choose a hydraulic or electric drive system in step #3
319 lbs
$1,864.00
605PTH
354 lbs
1,945.00
6506PTH
395 lbs
2,002.00
2. OPTIONAL FACTORY INSTALLED HYDRAULIC OR ELECTRIC SHUTOFF
Hydraulic shut-off attachment in lieu of hand lever (factory installed-hydraulic hoses not included) (user
supplies 1/4” hydraulic hoses from tractor to shutoff cylinder & 1/4” NPT fittings)
31 lbs
455.00
659711
6522
6512
6513
0107813
0107890
6521
0185214
01105214
01125214
657
658
659
654-5
3. SELECT A HYDRAULIC OR ELECTRIC DRIVE SYSTEM
*hydraulic drive package, less hoses for 3 pt hitch. (user supplies 1/4” hydraulic hoses from tractor to
shutoff cylinder and 1/4” NPT fittings.
Electric drive package, 12V for 3 pt hitch
Electric actuator shutoff attachment, retrofit
5. WEAR PARTS
NOVEMBER 2014
930.00
28 lbs
1,035.00
28 lbs
1,179.00
1 lbs
6 lbs
7 lbs
8 lbs
8 lbs
9 lbs
17.00
77.00
981.00
76.00
79.00
82.00
140.00
159.00
178.00
2 lbs
60.00
4 oz
GST # R101743045
Sheet 203
Standard Equipment:
• Precision-mated bottom & slide of cold milled steel
• Parking stand
• Choice of 16”, 18”, 20” & 26” tires
6500 SERIES ASB SPREADERS
4,5 & 6 ft Drop Spreader With Adjustable Slotted Bottom
For Spreading Agricultural Lime & Crumb Rubber
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
Specifications:
Tires: Choice of 16” pneumatic tires or 18” high-flotation pneumatic tires on steel rim.
Slot Size: 3-3/4” x 3/4” slotted openings spaced 1-inch apart and angled at 30-degrees. 12 openings on 4ft model and 19 openings on 6ft model.
Capacities: 4 ft, 4 cu ft (113 dm³) or approx 260 lbs (116 kg); 6-ft, 6 cu ft (170 dm³) or approx 390 lbs (174 kg)
Ground Clearance; 16” tires = 6”, 18” tires = 7”
6504 Wheel Spacing: 16” tires=51”, 18” tires=58-1/2””
6506 Wheel Spacing: 16” tires=75”, 18” tires=87-1/2””
6504 Overall Width: 16” tires=59”, 18” tires=66
6506 Overall Width: 16” tires=83”, 18” tires=90”
PART
NUMBER
6504ASB16H
DESCRIPTION
WGT
4ft spreader, 260 lb approximate capacity with stainless steel adjustable slotted bottom, push-handle and
16” pneumatic tires on steel rims
LIST
PRICE
FRT
EXTRA
230 lbs
$2,274.00
6504ASB18H
4ft spreader, 260 lb approximate capacity with stainless steel adjustable slotted bottom, push-handle and
18” high floatation tires on steel rims
234 lbs
2,405.00
6504ASB16T
4ft spreader, 260 lb approximate capacity with stainless steel adjustable slotted bottom, tow-hitch and
218 lbs
2,385.00
6504ASB18T
18” high floatation tires on steel rims
242 lbs
2,516.00
6506ASB16T
273 lbs
2,634.00
6506ASB18T
18” floatation tires on steel rims
277 lbs
2,776.00
2. REPLACEMENT TIRE PACKAGES, HUB AND RIM
65A16
16” Wheel package of two: steel hub and rims, pneumatic tire
15 lbs
241.00
65A18
18” Wheel package of two: steel hub and rims, 1” bore with 18 x 8.5 x 8 4-ply tubeless high-flotation
pneumatic tires
42 lbs
447.00
Hub to adapt 15 x 5K for 6.70 x 15 tire for greater clearance
6 lbs
213.00
Tire only, 6.70 x 15, 4-ply rib tubeless for greater clearance. Order 2 per spreader.
Bearing, center
Bearing, end
3. JIGGLER OPTIONS
4. RETROFIT KITS FOR EXISTING 4 AND 6-FT SERIES SPREADERS
Adjustable slotted bottom retrofit kit for existing 4-ft variable rate drop spreaders
Adjustable slotted bottom retrofit kit for existing 6-ft variable rate drop spreaders
19 lbs
18 lbs
2 lbs
2 lbs
85.00
178.00
60.00
135.00
8 lbs
9 lbs
140.00
178.00
6518-4
R01-0015-020
R02-0015-010
654-5
6524-8
657
659
6524
6526
NOVEMBER 2014
1,111.00
1,369.00
GST # R101743045
Sheet 203
Standard Equipment:
• Slotted, stainless steel bottom
• Specially designed rotor bar to agitate lime
• Choice of push-handle or tow-hitch on 4ft models
• Tow-hitch on 6ft model
• Choice of 16” or 18” pneumatic tirestires
Turf Tender®
24” Variable Rate Lawn Spreader
Spreads fertilizer, granular chemicals, granular lime, seed &
granular ice melts
www.gandy.net
TAB# 19 SPREADERS
US PRODUCT
Specifications:
24” hopper, 1.2 cu ft (33 dm³) volume, approx. 78 lbs (35 kg) capacity with fertilizer weighting 65 lbs per cu ft. 20 openings, 30-1/2” wide with 12” tires
and 35” wide with 13” tires. Powder coated steel hopper with stainless steel bottom and slide. Rate chart included.
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
24H12
24” drop spreader with push-handle, spread plate and 12” solid rubber tires
43 lbs
$535.00
24H13
24” drop spreader with push-handle, spread plate and 13” pneumatic tires
45 lbs
615.00
12” semi-pneumatic tire, carton of (1)
4 lbs
29.00
2813896
13” pneumatic tire package of (2)
10 lbs
150.00
28248584
Calibration pan, 24” spreader
4 lbs
75.00
2. FIELD INSTALLED OPTIONS & WEAR PARTS
28128657
2807953
Center bearing replacement
7 oz
22.00
090693
End bearing replacement
3 oz
7.00
28248725
Handle assembly, 24” spreader - replacement
5 lbs
113.00
5508214
Hole closure
3 oz
5.00
28247259
Jigglers for 24” spreaders to eliminate bridging. Order (2) per spreader
2 lbs
85.00
28248785
Spread plate assembly, 24” spreader– replacement
4 lbs
70.00
28248713
Tow hitch assembly, 24” spreader conversion pkg
5 lbs
112.00
28247968
Variable-rate bottom and slide for 24” spreader
3 lbs
117.00
NOVEMBER 2014
GST # R101743045
Sheet 203
Standard Equipment:
•
Adjustable stainless steel snap-off bottom and slide with triangular openings spaced 1 1/8” apart
•
Positive shutoff lever closes shutter slide, stopping flow
•
Steel tri-bar rotor gives internal agitation
•
Spread plates on all models
•
Bottom & slide snaps off for quick removal and cleaning
•
Porous, oil-impregnated bearings
•
Rate chart included
Turf Tender®
36” Variable Rate Lawn Spreader
Spreads fertilizer, granular chemicals, granular lime, seed &
granular ice melts
www.gandy.net
TAB# 19 SPREADERS
US PRODUCT
Specifications:
36” hopper, 1.8 cu ft (49 dm³) volume, approx. 120 lbs (53 kg) capacity with fertilizer weighting 65 lbs per cu ft. 30 openings, 30-1/2” wide with 12” tires
and 35” wide with 13” tires. Powder coated steel hopper with stainless steel bottom and slide. Rate chart included.
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
36H12
36” drop spreader with push-handle, spread plate and 12” solid rubber tires
52 lbs
$604.00
36H13
53 lbs
682.00
36T13
36” drop spreader with tractor hitch, spread plate and 13” semi-pneumatic tires
53 lbs
682.00
28128657
12” semi-pneumatic tire, carton of (1)
4 lbs
29.00
2813896
13” pneumatic tire package of (2)
10 lbs
150.00
28368584
Calibration pan, 36”spreader
4 lbs
75.00
2807953
7 oz
22.00
090693
3 oz
7.00
28368725
Handle assembly, 36” spreader
5 lbs
114.00
5508214
Hole closure
3 oz
5.00
28368759
2 lbs
93.00
M10-0005-014
Plastic rain cover with elastic band for 36” spreader
45.00
28368785
Spread plate assembly, 36” spreader -replacement
73.00
28368713
Tow hitch assembly, 36” spreader—replacement
4 lbs
113.00
28368768
3 lbs
145.00
NOVEMBER 2014
GST # R101743045
Sheet 203
Standard Equipment:
•
Adjustable stainless steel snap-off bottom and slide with triangular openings spaced 1 1/8” apart
•
•
•
•
•
•
Rate chart included
Turf Tender®
36” Fixed Rate Lawn Spreader
Spreads granular lime, commercial compost & seed
TAB# 19 SPREADERS
US PRODUCT
www.gandy.net
Specifications:
36” hopper, 1.8 cu ft (49 dm³) volume, approx. 120 lbs (53 kg) capacity. 46” wide . Powder coated steel hopper.
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
36H13FR
36” drop spreader with fixed-rate shutoff, push-handle and 13” pneumatic tires
52 lbs
$595.00
2. CHOOSE A 36” FIXED-RATE SPREADER BOTTOM
28368752-16S
Fixed-rate bottom, 1/4” slot, entire length, 36” spreader
4.25 lbs
52.00
28368752-20S
4.25 lbs
52.00
28368752-28S
4.25 lbs
52.00
28368752-32S
4.25 lbs
52.00
28368752-48S
4.25 lbs
52.00
28368752-64S
Fixed-rate bottom, 1” slot, entire length, 36” spreader
4.25 lbs
52.00
28368752-96S
Fixed-rate bottom, 1-1/2” slot, entire length, 36” spreader
4.25 lbs
52.00
2813896
13” pneumatic tire package of (2) - replacement
10 lbs
150.00
28368584
Calibration pan, 36”spreader
4 lbs
75.00
2807953
7 oz
22.00
090693
3 oz
7.00
28368725
Handle assembly, 36” spreader
5 lbs
114.00
28368713
Tow hitch assembly, 36” spreader—replacement
113.00
5508214
Hole closure
3 oz
5.00
28368759
2 lbs
93.00
28114
M10-0005-014
Lever rate pkg to convert a 24” or 36” fixed-rate spreader to a variable rate spreader (requires
bottom and slice - #28368768)
Plastic rain cover with elastic band for 36” spreader
28368741
Shutoff spread plate and crank attachment for 36” spreader when used with a fixed-rate bottom
6 lbs
145.00
28368768
3 lbs
145.00
NOVEMBER 2014
27.00
45.00
GST # R101743045
Sheet 203
Standard Equipment:
•
Choice of fixed-rate bottoms for spreading materials such as granulated lime & commercial compost
•
•
•
•
42” TURF TENDER SPREADER
42” Variable-Rate Lawn Spreader with
Push Handle or Tractor Hitch
TAB# 19 SPREADERS
US PRODUCT
Spreads fertilizer, granular chemical, granular lime, seed and granular ice melt
www.gandy.net
Specifications:
Capacity:
Openings:
Overall Width:
Overall Height:
Clearance:
PART
NUMBER
3.5cu ft (98 dm³), 225 lbs (102 kg), with fertilizer weighing 65 lbs per cu ft
36 triangular openings spaced 1” apart
center-to-center wheel spacing 45-3/4”; 48-1/2” with semi-pneumatic tire; 53-1/2” with pneumatic tire
30”
approx. 3-3/4” beneath spread plate with 16” tires 8-1/2” to hopper bottom
approx 5-3/4” beneath spread plate with 20” tires 10-1/2” to hopper bottom
approx 7-3/4” beneath spread plate with 26” tires 12-1/2” to hopper bottom
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
42H16
42” Turf Tender with push-handle, spread plate & 16” pneumatic wheels
95 lbs
$1,061.00
42T16
42” Turf Tender with tractor hitch, spread plate & 16” pneumatic wheels
80 lbs
1,061.00
2816896
16” pneumatic wheel pkg of two with adapters-replacement
18 lbs
207.00
28A20716
20” semi-pneumatic wheels of two with adapters-replacement
29 lbs
293.00
422.00
28A26716
26” semi-pneumatic wheels of two with adapters-replacement
50 lbs
28428584
Calibration pan, 42”
6 lbs
73.00
2807953
Center bearing
70 oz
22.00
152.00
28A426919
Cover assembly for 42” Turf Tender
9 lbs
090633-C1
End bearing
5 oz
31.00
42H-A
Handle assembly
15 lbs
169.00
284295109
Handle for use in place of tractor hitch (uses existing holes)
7 lbs
126.00
5508214
Hole closure
3 oz
5.00
28427159-1
Jigglers, left to eliminate bridging (requires left & right)
5 lbs
61.00
28427159-2
Jigglers, right, to eliminate bridging (requires left & right)
5 lbs
61.00
42T-A
Tow hitch assembly
17 lbs
163.00
284295108
Tractor hitch for use in place of handle
7 lbs
126.00
2808942-7
Variable-rate bottom and slide, for 42” spreader
5 lbs
169.00
NOVEMBER 2014
GST # R101743045
Sheet 203
Standard Equipment:
•
Adjustable variable-rate stainless steel bottom and slide with triangular openings
•
Bottom& slide snaps off for quick removal and cleaning
•
Positive shutoff lever closes slide
•
•
•
•
All models disassemble for easy cleaning
TAB# 19 SPREADERS
US PRODUCT
TURF TENDER
www.gandy.net
42” Variable-Rate Lawn Spreader with Optional 3PT Hitch
Spreads fertilizer, granular chemicals, granular lime, seed & granular ice melts
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
2842PTH
42” drop spreader with parking stand and two, 12-volt electric motor drives
203 lbs
$1,798.00
2. CHOOSE A 3PT HITCH OPTIONS (NOT REQUIRED IF YOU WANT TO JUST USE PARKING STANDS)
2892
Cat 0, 3pt hitch (2842PTH only)
35 lbs
159.00
2305880
Cat 1, 3pt hitch (2842PTH only)
53 lbs
285.00
28428584
6 lbs
73.00
2807953
Center bearing
7 oz
22.00
2891-D
Cover (2842PTH only)
9 lbs
134.00
090633-C1
End bearing
5 oz
31.00
5508214
Hole closure
3 oz
5.00
28427159-1
Jigglers, left to eliminate bridging (requires left & right)
5 lbs.
61.00
28427159-2
Jigglers, right, to eliminate bridging (requires left & right)
5 lbs
61.00
2808942-7
Variable-rate bottom and slide, for 42” spreader
5 lbs
169.00
NOVEMBER 2014
GST # R101743045
Sheet 203
Standard Equipment:
•
Adjustable variable-rate stainless steel bottom and slide with triangular openings
•
Bottom& slide snaps off for quick removal and cleaning
•
Hand-lever shutoff
•
•
Two, 12-volt electric motors provide internal agitation
•
•
Disassembles for easy cleaning
Turf Tender®
42” Fixed Rate Lawn Spreader
TAB# 19 SPREADERS
US PRODUCT
Spreads granular lime, commercial compost & seed
www.gandy.net
PART
NUMBER
DESCRIPTION
WGT
LIST PRICE
FRT EXTRA
42H16FR
95 lbs
$1,016.00
42T16FR
42” drop spreader with tow hitch, spread plate and 16” pneumatic tires
95 lbs
1,008.00
28427852-12S
Fixed-rate bottom, 3/16” slot, entire length
2. CHOOSE A 36” FIXED-RATE SPREADER BOTTOM
5.25 lbs
52.00
28428752-16S
5.25 lbs
52.00
28428752-20S
5.25 lbs
52.00
28427852-24S
5.25 lbs
52.00
28427852-28S
Fixed-rate bottom, 7/16” slot, entire length (mulched seeds)
5.25 lbs
52.00
28427852-32S
5.25 lbs
52.00
28427852-40S
5.25 lbs
52.00
28427852-48S
5.25 lbs
52.00
28427852-64S
Fixed-rate bottom, 1” slot, entire length
5.25 lbs
52.00
28427852-96S
Fixed-rate bottom, 1-1/2” slot, entire length
5.25 lbs
52.00
6 lbs
73.00
28428584
2807953
7 oz
22.00
28A426919
Cover assembly for 42” Turf Tender
9 lbs
152.00
284294102
Crank attachment for fixed-rate bottoms, 42H spreaders
7 lbs
60.00
28494101
Crank attachment for fixed-rate bottoms, 42T spreaders
5 oz
73.00
090633-C1
End bearing, 42” spreader
28427225
Handle for use in place of tow hitch with fixed-rat bottom. Note: must have pole on spreader.
5 oz
31.00
10 lbs
167.00
5508214
Hole closure
3 oz
5.00
28427159-1
5 lbs
61.00
28427159-2
5 lbs
61.00
28113
28427013
Lever pkg for rate adjustment of 42” variable rate bottom & slide when used with fixed-rate shutoff models ending in “FR”. (requires variable rate bottom & slide, #2808942-7)
Tractor hitch for used in place of handle with fixed-rate bottom
7 lbs
124.00
2808942-7
Variable-rate bottom and slide, ordered as an option for 42” “FR” spreader
5 lbs
169.00
NOVEMBER 2014
58.00
GST # R101743045
Sheet 203
Standard Equipment:
•
Spread-plate shutoff mechanism
•
•
All models disassemble for easy cleaning
“All Applicable Taxes Extra”
EUROSPAND (O.M.B.) BROADCAST
FERTILIZER & SALT SPREADER
www.eurospand.it
490 & 890 PXT
•
•
•
•
•
•
TAB: #19 SPREADERS
Capacity: 200 lt / 53 gal
Steel hopper with powder coat paint
Spreading width, up to 30 ft
Independent levers for spreading
Adjustable spreading vanes
Optional agitator available
Ercole
•
•
Capacity: 400 lt, 800 lt
Stainless Steel hopper
S273L
Spreading width: from 4 to 12 meters
Opening: Manual or Hydraulic
Linkage: Cat l and ll
•
•
Capacity: 800 lt - 1200 LT
stainless steel hopper (fertilizer version) hot galvanized chassis plus two powder
coatings layers (salt version)
Spreading width 18 meters
Hydraulic control
Note: Fertilizer Tank Capacity is based on fertilizer that has a density of 64 lbs/cubic ft A different density will change what the fertilizer tank can hold.
Model
Number
Description
List
Price
Single Disc Spreader
S273L
3-point hitch steel fertilizer spreader with PTO shaft - 200 lt capacity, approx 440 lbs Spreading disc has
adjustable vanes to allow accurate & uniform spread for all types of fertilizer.
A002.001
G006.005
Agitator for S273L
Deflector to limit the spreading width for S273L
S935.002
Ercole, 3-point - single disc - stainless steel spreader with filtering grid to brake up lumps, with hydraulic
control - 800 lt (approx 1,760 lbs) , 1,000 lt (approx 2,200 lbs & 1,200 lt (approx 2,640 lbs ) ft capacity
A002.019
Agitator for Ercole fertilizer spreader
R002.089
200 lt Stainless Steel extension
$550.00
62.00
220.00
3,380.00
83.00
357.00
Single Disc Salt Spreader
S935.004
Ercole, 3-point - single disc spreader– with 420 rpm reduced gearbox - hot galvanized chassis plus two
powder coating layers, with filtering grid to brake up lumps, with hydraulic control 800 lt (approx 1760 lbs), 1,000 lt (approx 2200 lbs), & 1,200 lt (approx 2640 lbs), capacity.
A002.023
Agitator for Ercole salt spreader
4,708.00
99.00
Pendulum Spreaders
490PXT INOX
Pendulum type 3-point spreader with stainless steel hopper & filtering grid to brake up lumps - a
capacity of 400 lt (approx 880 lbs), spread width 4 to 12 meters
2,495.00
890PXT INOX
Same as above but with a 800 lt approx 1760 lbs) stainless steel tank.
3,686.00
A002.009
Agitator for 490 - 890PXT
G010.044
Hydraulic remote control for 490 – 890PXT
JANUARY 2014
PRICES ON MANUFACTURED GOODS SUBJECT TO CHANGE
84.00
318.00
GST # R101743045
Sheet 203
NOTE: PRODUCT NOT IN STOCK IS SUBJECT TO EXTRA FREIGHT CHARGES
•
•
•
•
•
TAB: #19 SPREADERS
www.eurospand.it
EUROSPAND (O.M.B.) BROADCAST FERTILIZER
SPREADER & SEEDER
•
•
•
David
•
•
•
•
•
David Fruit
Capacity: 600 lt,- 1,000 lt
Powder coat or stainless steel hopper
Spreading width: up to 15 meters
Left & right hydraulic control
Linkage: Cat ll
Jolly
•
•
•
•
•
Capacity: 1600 lt - 3000 lt
Spreading width: 28 to 32 meters
Left and right hydraulic control
Linkage: Cat ll
Note: Fertilizer Tank Capacity is based on fertilizer that has a density of 64 lbs/cubic ft A different density will change what the fertilizer tank can hold.
Model
Number
Description
S926.001
David
Twin disc spreader with 600 - 1000 lt capacity (approx 1,320-2,200 lbs), powder coated paint, Vibro System,
left & right hydraulic control - made for narrow passages between plants in rows - spreading width up to 15
meters
Stainless Steel - Twin disc spreader with 600 - 1000 lt capacity (approx 1,320-2,200 lbs), , powder coated
paint, Vibro System, left & right hydraulic control - made for narrow passages between plants in rowsspreading width up to 15 meters
SPECIAL
ORDER
SPECIAL
ORDER
S926.007
David Fruit
Inox
Twin disc spreader with 600 - 1000 lt capacity (approx 1,320-2,200 lbs), , powder coated paint, Vibro System,
left & right hydraulic control - made for narrow passages between plants in rows - row– localized distribution
from 2 - up to 5 meters - open field distribution up to 12 meters
Stainless Steel - Twin disc spreader with 600 - 1000 lt capacity (approx 1,320-2,200 lbs), , powder coated
paint, Vibro System, left & right hydraulic control - made for narrow passages between plants in rows - localized distribution from 2 - up to 5 meters - open field distribution up to 12 meters
Jolly 28
Twin disc spreader with 1600 lt - 3000 lt capacity (approx 3,520-6,600 lbs), stainless steel grid, Vibro System, left & right hydraulic control, tilting hopper working width up to 28 meters, 540 RPM
SPECIAL
ORDER
Jolly 28 Inox
Stainless Steel - Twin disc spreader with 1600 lt - 3000 lt capacity (approx 3,520-6,600 lbs), , stainless steel
grid, Vibro System, left & right hydraulic control, tilting hopper working width up to 28 meters, 540 RPM.
SPECIAL
ORDER
Jolly32
Twin disc spreader with 1600 lt - 3000 lt capacity (approx 3,520-6,600 lbs), , stainless steel grid, Vibro System, left & right hydraulic control, tilting hopper working width up to 32 meters, 1000 RPM
SPECIAL
ORDER
Jolly 32 Inox
Stainless Steel - Twin disc spreader with 1600 lt - 3000 lt capacity (approx 3,520-6,600 lbs), , stainless steel
grid, Vibro System, left & right hydraulic control, tilting hopper working width up to 32 meters, 1000 RPM.
.
SPECIAL
ORDER
List
Price
Double Disc Spreaders
S926.003
David Inox
S926.006
David Fruit
SPECIAL
ORDER
SPECIAL
ORDER
These Spreaders Are Special Order only Not Regular Stock Items
Please Call for More Information
JANUARY 2014
GST # R101743045
Sheet 203
•
•
Capacity: 600 lt,- 1,000 lt
Spreading width: row-localized distribution from 2 - 5 meters or open filed
distribution up to 12 meters
Left & right hydraulic control
Linkage: Cat ll
TAB: #19 SPREADERS
U. S. PRODUCT
www.curtisindustries.com
•
•
•
Fast-Cast 2000 Series - 1CS1
Features:
•
•
•
Rock salt, Fertilizers and
light duty grade applications
3.0 cu. ft./180 lbs. capacity
4 to 24 ft. spreading width
Features:
•
•
•
Rock salt, Deicers and Free
Flowing Materials
Fast-Cast 550 Series - 1CS6H
Features:
•
•
•
•
•
•
5.5 Honda Vertical Shaft Gas Engine
500 lbs. capacity
Adjustable Material Deflectors
In-Cab Control Panel
Aluminum Hopper
Model
Number
Description
1CS1
1SM2
1SM3
1SV1
1CS9
1CS10
1SC3
1SM4
1WC3
1GC1
1GC1A
1AD1
1CS6H
1CS6E
1WC2
1CS6-SCR
Fertilizers and Fine Material
grade applications
Fast-Cast 550 Series - 1CS6E
Features:
•
•
•
•
•
•
Motor draws less than 20 Amps
500 lbs. capacity
Adjustable Material Deflectors
In-Cab Control Panel
Aluminum Hopper
Weight
List
Price Frt
Extra
Fast-Cast 2000 Tailgate Spreader (requires mount kit)
85 lbs
$1,827.00
Reese Hitch Mount (required for all CS1 installations)
3-Point Hitch Mount (requires 1SM2 Reese hitch mount)
Vibrator Kit (Fast Cast 2000 only)
Fast-Cast 300 Rock Salt Spreader - Reese Mount Included
Fast-Cast 400 Fine material Spreader - Reese Mount Included
Variable Speed Control For Fast Cast 300 & 400
Drop Utility Mount
Weather Cover for Fast Cast 300 & 400
Gate Flow Control kit F/1CS1 & 1CS3
Cable (only) For Gate Flow Control
Adjustable Deflector
Fast Cast 550 1/3 Yard Spreader - Aluminum Hopper w/Honda Engine
Fast Cast 550 1/3 Yard Spreader - Aluminum Hopper w/Electric Engine
Weather Cover for Fast Cast 550
Top Screen Option - Fast Cast 550
15 lbs
30 lbs
20 lbs
75 lbs
75 lbs
5 lbs
20 lbs
5 lbs
5 lbs
5 lbs
4 lbs
380 lbs
350 lbs
1 lbs
75 lbs
198.00
303.00
426.00
1,050.00
1.141.00
296.00
426.00
51.00
310.00
194.00
219.00
5,239.00
5,482.00
115.00
407.00
JANUARY 2014
GST # R101743045
Sheet 203
Features:
TAB: #19 SPREADERS
U. S. PRODUCT
www.fergusonmfgco.com
FERGUSON ONE‑ROW FERTILIZER DISTRIBUTORS
DESCRIPTION
FER 61FW
Fertilizer Distributor, 1‑row rear mount, ground
wheel drive, for Pittsburgh type cultivator frame
CULTIVATOR FRAME NOT INCLUDED.
Weight 165 lbs.
CALL FOR
PRICE
MODEL #
FERGUSON FERTILIZER SIDE DRESSERS
FER 69DW
Fertilizer Distributor, 2‑row, rear mount, ground
Wheel drive, for diamond toolbar,
TOOL BAR NOT INCLUDED.
Weight 205 lbs.
FERGUSON FERTILIZER ATTACHMENTS
FER RG102S
Two Row, one 550 lbs. Hopper, two drops complete
with hydraulic drive and mtg. brackets for
4” X 4”, 4" x 7", flat mounted bars, 36"‑ 48" rows.
Weight 320 lbs.
FER RG104S
Four row, two 550 lbs. Hopper, two drops each,
complete with hydraulic drive and mounting
brackets or 4" x 4", 4" x 7" flat mounted and
7" x 4", 7" x 5" & 7" x 7" vertical mounted
bars, 36" & 42" rows.
Weight 485 lbs.
JANUARY 2014
GST # R101743045
Sheet 203

sec 19 spreaders - Maritime Farm Supply ltd.

Transcription

Similar documents

Softub T-220 - Softub of the Carolinas

K9 SUPERFUEL TM Human Grade Ingredients

Softub T-140 - Softub of the Carolinas

VFX-9/13 Pneumatic Combination Tool for Polypropylene

SHRINKFAST.

SC-2300 spec

Avon Cobra Tires for Honda GL1800

recycling done right - Vancouver

PermaScreen 70 | Tennis Windscreens

Hand Crank Spreader Rate Setting Instructions