Door Closers - ConstructionBuildingComponents.com

Transcription

Door Closers
DOOR CLOSER
Philadelphia Hardware Group, Inc. is presenting the finest ADVANTAGE® surface mounting door closers
for your various application demands. There are
• Multi-size door closer: 9000, 8000, 6000, 6000S (slim cover), 5000, 4400 series.
• Standard size door closer: 4000, 3000, 2000 series.
• Multi-size Delay Action door closer: 8000/DA, 6000/DA, 6000S/DA series.
GENERAL INFORMATION
ANSI A156.4 – American National Standard for Door Controls-Closers
ADVANTAGE® Grade 1 Door Closers are certified by ANSI/BHMA A156.4.
ADVANTAGE® Grade 2 Door Closers are factory tested to meet or exceed ANSI Grade 2 required strength and performance.
UL Listed
All of ADVANTAGE® door closer series are UL listed, and conforms to Standards UL10C and UPC 7-2(1997).
Meet ADA requirements
ADVANTAGE® door closer 9000, 8000, 6000, and 4400 series meet ANSI A117.1 requirements for ADA.
Please note Door Closer with reduced opening force may not provide sufficient power to close a door.
• Doorways shall have a clear opening of 32” minimum. Clear opening of doorways with swinging doors shall be measured from
the face of door and stop with the door open 90°.
• Door closers shall be adjusted so that from the open position of 90° the time required to move the door to an open position of
12° shall be 5 seconds minimum.
• The maximum force for pushing open or pulling open doors other than fire doors shall be as follows:
1. Interior hinged door: 5 lbs.
2. Exterior hinged door: 8.5 lbs.
* 4400 series apply to interior hinged door only.
Handing
All ADVANTAGE® Door closers are non-handed that are suitable for left-opening or right-opening door.
All Weather Hydraulic Fluid used to ensure smooth operation under severe weather conditions.
Finish Stock available Aluminum (BHMA 689) for all model
Duranodic (BHMA 695) for all model
Gold (BHMA 696) for all model
Satin Chrome (BHMA 652) for 8000 series
Aluminum
Duro (Duranodic)
Gold
ACCESSORIES
Drop Plate allows a door closer to be fitted on narrow top rail or narrow top frame door.
Most of the ADVANTAGE® door closers have different kinds of Drop Plates for installation requirements, see following pages in detail.
Hold Open Arm used when door is requiring for a clear opening doorways at 90˚ stop.
* Should not be used on Fire door application.
Parallel Rigid Cush Arm is a heavy duty arm with an auxiliary stop in soffit shoe to stop the door opening at a specific
point. Apply to door where wall or floor stops are not appropriate. Parallel arm mounting application only.
Parallel Rigid Cush and Stop Arm is a heavy duty hold open arm featured with a plunger hold open to engage or
disengage hold open by a handle on the arm. Parallel arm mounting application only.
* Should not be used on Fire door application.
1
DOOR CLOSER
DOOR CLOSER APPLICATION
There are three basic methods of mounting surface door closers to the door and frame including regular arm, parallel arm and top
jamb mounts. All ADVANTAGE® door closers are supplied standard with a tri-pack for mounting any of three types applications.
Parallel Arm Installation
Regular Arm
Installation
Top Jamb
Installation
closer mounts
on hinge
(pull) side of door
closer mounts
on frame face on
opposite to hinge
(pull) side of door
closer mounts on
opposite to hinge (pull) side of door
Left hand door-LH
Right hand reverse-RHR
Right hand door-RH
Left hand reverse-LHR
Left hand door-LH
Right hand door-RH
Left hand door-LH
Right hand door-RH
Use adjustable wrench to rotate spindle 45°
counter-clockwise for right hand door or clockwise
for left hand door. Place main arm on spindle so
that the “R” (Right hand door) or “L” (Left hand door)
lines up with the spindle flat. Secure main arm and
spindle by tightening spindle bolt.
Regular Arm (Pull side)
Top Jamb (Push side)
Parallel Arm (Push side)
Most power-efficient application
The Closer body is mounted on the
hinge side of the door top rail.
The forearm is mounted to the frame
face by a mounting shoe.
Arm projects at approximately a 90°
angle away from the door.
More power-efficient than the
parallel arm application
Applying to a closer with narrow top
rail on a door.
The closer body is mounted to the
frame face above the door, opposite
the door hinge side.
The forearm is then mounted to the
top rail of the door.
Least power-efficient application
The closer body is mounted on the top
rail of the door, opposite the hinge side
of the door.
The forearm is mounted by a
parallel arm bracket to the underside
of the frame.
The arm is parallel to the door, which
makes it less likely to be damaged.
* Top reveal should have enough space
for using this application.
CLOSER ADJUSTMENT
ADVANTAGE® Door closers have hex wrench controlling valves for adjusting Closing speed and latch speed.
Multi-size door closers have a nut for spring power adjustment, and additional valve for Backcheck.
Delay Action control valve available with Delay Action model.
Opening Cycle
2
DOOR CLOSER
Closing speed &
Latching speed are
dual valve control for door
closing speed.
Closing speed is the speed of
door closing from full opening
to approximately 10˚~5˚ of door
closed position.
Latching speed is the speed
from approximately 10˚~5˚ door
opening to door closed position. Slow latch speed provides
less door closing noise.
Backcheck slows down the
door opening at approximately
70˚ in order to prevent damage
to building and door frames.
The backcheck control valve
provides a 20˚ adjustment (70˚
~ 90˚) to set the optimum backcheck start point.
* Multi-size door closers are
standard with Backcheck
function.
Delay Action is the 3rd
control for closing speed adjustment.
It effective from full opening
to approximately 70˚, and
provides a slow closing speed.
The closing time between 180˚
to 70˚ is at least 20seconds,
and easily adjustable up to
1minutes. Closer with Delay
Action provides sufficient
time that allows people or the
elderly to get through the door
before it starts to close.
Multi-size Spring adjustment
Multi-size door closers are able to adjust the spring power to meet the power needs of the door.
Spring power of the closer can be increased by turning the power adjustment nut clockwise, vice versa.
Closer Size (Spring Power)
Re c omm e n d e d Ma x i m u m Do o r S i z e
Closer
Regular & Top Jamb
Parallel Arm
Interior
Exterior Swing-in
(Pull Side)
Exterior Swing-out
(Push Side
Interior Swing-out
(Push side)
Exterior Swing-out
(Push side)
(Lbs.)
1
28”
N/A
N/A
N/A
N/A
33 ~ 66
2
36”
N/A
N/A
30”
N/A
66 ~ 99
3
42”
30”
36”
36”
30”
99 ~ 143
4
48”
36”
42”
42”
36”
143 ~ 187
5
54”
42”
48”
48”
42”
187 ~ 264
6
60”
48”
54”
54”
48”
264 ~ 330
* Multi-size door closers provide the spring power required to fit your door size and application.
3
Door Weight
Size
9000 SERIES
UL
ANSI GRADE 1
ANSI/BHMA A156.4-2000
Series 2000, PT1
Exceeds 1,500,000 cycles with Backcheck
Model
9000
R
LISTED
ANSI GRADE 1
UL10C Positive Pressure
Rated. Conforms to UBC
7-2 (1997). (Uniform
Building Code Standard)
Comply with
ANSI A117.1
25-Year Warranty
Adjustable power size 1-6 with Back Check
Applications
• Heavy Duty Commercial model ideal for high traffic door
such as schools, hospitals, and public institutions
• Same mounting hole pattern as CAL-ROYAL 900
(CTC 11-1/8” x 1-1/8”), ideal for renovations
• Tri-packed for all type applications
Features
• Multi-size spring adjustable power size 1-6
Factory preset size 3
• Meet ADA
• Standard with adjustable Backcheck
Product Specification
Optional Fuctions
Material
•
•
•
•
•
Cover
Valves
Arm &
Brackets
Screws
Finishes
Aluminum alloy body, forged steel arm
Heat treated forged steel piston
Double Heat treated Steel pinion
Full plastic cover – standard
Triple valve control for Closing speed, Latching speed,
and Back-check
Staked valve for power adjustment
Standard arm and parallel bracket included for different
mounting demand
Self-tapping wood screws and machine screws
Aluminum, Duronotic, and Gold
Hold Open Arm (9001)
Parallel Rigid Cush Arm (9002)
Parallel Rigid Cush and Stop Arm (9003)
Extended forearm (9004)
Sex-bolts (Metal door mounting)
* Special order from the factory
• Delay Action
• Metal cover
• Plated Finish: US3, US26, US26D
Technical Dimensions
Series 9000
A. Length of Closer Body
B. Horizontal Mounting Holes
C. Vertical Mounting Holes
D. Height of Closer Body
E. Projection from Door
Size
11-7/8”
11-1/8”
1-1/8”
2”
2-3/8”
End View
Front View
Accessories
9001
Hold-open Arm
Stand for pull side & top jamb
Use with PA bracket for
parallel arm mount
9002
Parallel Rigid
Cush Arm
Auxiliary Stop in
soffit shoe
9003
Parallel Rigid
Cush and Stop Arm
Hand control plunger
stop in soffit shoe
9004
Extended Forearm
For Top Jamb with reveal
greater than 4” and up
to 8”
90C
Standard Full
Plastic Cover
1348
Sex-bolt with screw
For 1-3/4” standard Door Thick
PAB01
Parallel Bracket
for Hold Open Arm mounting
can also use for regular
4
8000 SERIES
ANSI GRADE 1
Series 2000, PT1
Model
8000
8000/DA
UL
R
LISTED
ANSI GRADE 1
7-2 (1997). (Uniform
Comply with
ANSI A117.1
25-Year Warranty
Adjustable power size 1-6 with Delay Action
Applications
• Extra Heavy Duty Commercial model ideal for high traffic door
•
•
Versatile for new constructions, such as schools, hospitals,
and public institutions
Same mounting hole pattern as LCN4041, ideal for renovations
Tri-packed for all type applications
Features
• Multi-size spring adjustable power size 1-6
• Meet ADA
Optional Fuctions
Material
Wide choice of options for different applications
• Hold Open Arm (8001)
• Parallel Rigid Cush Arm (8002)
• Parallel Rigid Cush and Stop Arm (8003)
• Extended forearm (8004)
• Drop Plate (see Accessories)
• Sex-bolts (Metal door mounting)
Cover
Valves
Arm &
Brackets
Screws
Finishes
Heavy Duty Cast Iron body, forged steel arm
and Back-check cushion
Delayed Action valve – Optional (Model: 8000DA)
mounting demand
Aluminum, Duronotic, Gold, and US26D-Satin Chrome
• Metal cover
• Plated Finish: US3, US26
Accessories
Size
Series 8000
11”
5”
1”
2-3/4”
2”
8001
Hold-open Arm
parallel arm mount
PAB01
Parallel Bracket
5
8002
Parallel Rigid
Cush Arm
Auxiliary Stop in
soffit shoe
Front View
End View
8003
Parallel Rigid
Cush and Stop Arm
stop in soffit shoe
8004
Extended Forearm
For Top Jamb with
reveal between
2-5/8” to 4-13/16”
80C
Standard Full Plastic Cover
1348
Sex-bolt with screw
80DP-ST
Size: 12-1/4 x 3-9/16”
Drop Plate – Pull Side
Hinge side mount when top rail is less than 3-3/4”
Plate require 2” minimum top rail
80DP-TJ
Size: 12-1/4 x 3-9/16”
Drop Plate – Top Jamb
Use when frame face is less than 3 1/2”
Use 8004 forearm if top reveal exceeds 2-9/16”
80DP-TG
Size: 12-1/4 x 3-9/16”
with flush ceiling
Top of head frame face in flush ceiling condition
Plate requires 1-3/4” minimum frame face
Use 8004 forearm if top reveal exceeds 2-9/16”
80DP-PA
Size: 12-1/4 x 5”
Drop Plate – Parallel Arm
Use when top rail is less than
5-1/2”, measured from the stop
Plate requires at least 2-1/2” top rail
6000, 6000S SERIES
UL
ANSI GRADE 1
Series 2000, PT1
Model
6000, 6000S
6000/DA, 6000S/DA
R
LISTED
7-2 (1997). (Uniform
ANSI GRADE 1
Comply with
ANSI A117.1
25-Year Warranty
Adjustable power size 1-6 with Back Check and Delay Action
Full Cover
Applications
• Heavy Duty Commercial model ideal for high traffic door
•
•
Versatile for new constructions, such as schools,
hospitals, and public institutions
Same mounting hole pattern as NORTON 8000 CTC 12” x 3/4”,
ideal for renovations
Slim Cover
Features
• New upgraded design from year 2009
•
•
Multi-size spring adjustable power size 1-6,
Meet ADA
Standard with adjustable Backcheck
Optional Fuctions
Material
Cover
Valves
Arm &
Brackets
Screws
Finishes
Full plastic cover – 6000 series
Triple valve control for Closing speed, Latching speed, and
Back-check
Delayed Action valve – Optional (Model: 6000/DA, 6000S/DA)
mounting demand
Wide choice of options for different applications
Hold Open Arm (6001)
Parallel Rigid Cush Arm (6002)
Parallel Rigid Cush and Stop Arm (6003)
Extended forearm (6004)
Drop Plate (see Accessories)
•
•
•
•
•
•
• Metal cover (Full Cover only)
• Plated Finish: US3, US26, US26D
Accessories
Size
Series 6000, 6000S
12-3/4”
B. Horizontal Mounting Holes 12”
3/4”
1-1/4”
2-1/8” End View
6001
Hold-open Arm
parallel arm mount
PAB01
Parallel Bracket
1348
Sex-bolt with screw
6002
Parallel Rigid
Cush Arm
Auxiliary Stop in
soffit shoe
6003
Parallel Rigid
Cush and Stop Arm
stop in soffit shoe
Front View
6004
Extended Forearm
For Top Jamb with reveal
greater than 4” and up
to 8”
60C-F
Standard Full Plastic Cover
60C-S
Standard Slim Plastic Cover
60DP-ST
Size: 13-1/8 x 3-1/4”
Drop Plate – Pull Side , or
Concealed Door Holder
Use for hinge side mount
Upside-down to mount where concealed door
holder prevents normal door closer mounting
Plate require 2-7/16” minimum top rail
60DP-TJ
Size: 13-1/8 x 3-5/8”
Apply to low ceiling clearance between
1-1/2” ~ 1-3/4”
60DP-PAS
Size: 13-1/8 x 3-5/8”
Drop Plate – Parallel Arm
Plate require 2-7/8” minimum top rail
Cross reference: NORTON #3148
60DP-PA
Size: 13-1/8 x 5”
Drop Plate –
Parallel arm mount
Used to mount a closer on a top rail as
narrow as 3” in height
6
5000, 4400 SERIES
UL
ANSI GRADE 1
Series 2000, PT1
Model
5000
4400
R
LISTED
7-2 (1997). (Uniform
ANSI GRADE 1
4400 Series
Comply with
ANSI A117.1
25-Year Warranty
Applications
• Heavy Duty Commercial model, ideal for high traffic door
•
•
Versatile for new constructions, such as schools, hospitals,
and public institutions
Universal mounting hole pattern
Size 4: CTC 9-1/16” x 3/4”
Features
• Multi-size spring adjustable power size 3-6, factory preset size 4
Multi-size spring adjustable power size 1-4, factory preset size 3
• 4400 meets ADA, Barrier Free interior
• Standard with adjustable Backcheck
Optional Fuctions
Material
• Hold Open Arm (4001)
• Drop Plate (see Accessories)
• Sex-bolts (Metal door mounting)
Cover
Valves
Arm &
Brackets
Screws
Finishes
and Back-check
mounting demand
Series 5000, 4400
Size
9-3/4” 9-3/4”
9-1/16” 9-1/16”
3/4”
3/4”
1-3/4” 1-3/4”
2-7/8” 2-7/8” End View
Front View
Accessories
4001
Hold-open Arm
Stand for pull side
and top jamb
Use with PA bracket for parallel arm mount
PAB02
Parallel Bracket
7
40C
Standard Full
Plastic Cover
1348
Sex-bolt with screw
40DP-TJ
Size: 9-3/4” x 2-9/16”
Drop Plate –Top Jamb
low ceiling clearance
For use when ceiling clearance is between
1-3/4” and 2-5/8”
Cross reference: NORTON #1687
40DP-PA
Size: 9-3/4” x 3-1/2”
Drop Plate –Parallel
arm mount
Used to mount a closer on a top rail as narrow as 2-5/8” in height
4000, 3000, 2000 SERIES
UL
GRADE 2
Factory tested to meet
ANSI Grade 2 durability
R
LISTED
Model
4000
3000
2000
7-2 (1997). (Uniform
ANSI GRADE 2
10-Year Warranty
Standard power size 4
Applications
• Medium and Light Duty model
•
Medium Duty 4000
Light Duty
3000, 2000
Universal mounting hole pattern
Size 4: CTC 9-1/16” x 3/4”
Size 3: CTC 8-3/16” x 3/4”
Size 2: CTC 6-5/8” x 3/4”
Optional Fuctions
Material
•
•
•
•
Valves
Arm &
Brackets
Screws
Finishes
and Back-check
mounting demand
Wood screws and machine screws
Hold Open Arm (3001, 4001)
Drop Plate (See Accessories)
Full plastic cover, available for 4000 series
only (40C)
Series 4000, 3000, 2000
9-3/4”
9-1/16”
3/4”
1-3/4”
2-7/8”
Size
8-3/4”
8-3/16”
3/4”
1-3/4”
2-7/8”
7-5/16”
6-5/8”
3/4”
1-3/4”
2-5/8”
End View
Front View
Accessories
4001
Hold-open Arm
For 4000 Series
Pull side and top jamb
3001
Hold-open Arm
For 3000 Series
Pull side and top jamb
PAB02
Parallel Bracket
40C
For 4000 Series
Standard Full
Plastic Cover
1348
Sex-bolt with screw
40DP-TJ For 4000 Series
Size: 9-3/4” x 2-9/16”
Drop Plate –Top Jamb
low ceiling clearance
For use When ceiling clearance is between
1-3/4” and 2-5/8”
40DP-PA For 4000 Series
Size: 9-3/4” x 3-1/2”
Drop Plate –Parallel
arm mount
Used to mount a closer on a top rail as
narrow as 2-5/8” in height
Size: 3-1/2” x 8-3/4”
Drop Plate – Parallel arm mount
Size: 3-1/2” x 7-5/16”
Drop Plate – Parallel arm mount
8
ORDER INFORMATION
Product Availabilities
Series Power Size
Duty
9000
Adjustable No. 1-6
Heavy
8000
Adjustable No. 1-6
Extra Heavy
8000/DA
Adjustable No. 1-6
Extra Heavy
6000
Adjustable No. 1-6
Heavy
6000S
Adjustable No. 1-6
Heavy
6000/DA
Adjustable No. 1-6
Heavy
6000S/DA Adjustable No. 1-6
Heavy
5000
Adjustable No. 3-6
Heavy
4400
Adjustable No. 1-4
Heavy
4000
No. 4
Medium
3000
No. 3
Light
2000
No. 2
Light
Function Availability
Back Delay
Check Action
Hold Open with
Hold Open Arm
Accessories
Parallel Rigid
Cush Arm
Cush &
Stop Arm
Drop
Plate
Sex- Plastic Metal
Bolt Cover Cover
● Standard or optional
● Special order from the factory, allow for longer lead time. Please call for more information
ADVANTAGE® Door Closers Power Size
Adjustable Power with Back-Check (BC)
Product Code
Aluminum
Duro
Gold
9000
No. 1-6 BC
609910
609911
609912
8000
No. 1-6 BC
608810
608811
608812
6000
No. 1-6 BC
606710
606711
606712
6000S (Slim Cover)
No. 1-6 BC
606730
606731
606732
5000
No. 3-6 BC
605110
605111
605112
4400
No. 1-4 BC
604410
604411
604412
Adjustable Power with Back-Check (BC) and Delay Action (DA)
6000/DA
No. 1-6 BC DA
606740
606741
606742
6000S/DA (Slim Cover)
No. 1-6 BC DA
606750
606751
606752
No. 1-6 DA
608840
608841
608842
4000
No. 4
604010
604011
604012
3000
No. 3
603300
603301
603302
2000
No. 2
602200
602201
602202
Adjustable Power with Delay Action (DA)
8000/DA
Fixed Power Size
9
CROSS REFERENCE
ADVANTAGE®
9000
8000
Spring Power Size
1–6
1–6
CTC Hole Pattern 11-1/8” x 1-1/8” 5” x 2-1/4” x 1”
ARROW
CAL-ROYAL
6000S
N900-PBF
● DC6200
RUSSWIN
● DC3200
PR74BC
DESIGN
CR441
● DC8000
5000/4400
4000
3000
2000
1–6
1–6
3 – 6/1 – 4
4
3
2
12” x ¾”
12” x ¾”
9-1/16” x ¾”
9-1/16” x ¾”
8-3/16” x ¾”
6-5/8” x ¾”
936N/DC214
DC204
● DC203
300
740
730
● 720
440-FP
430-P
● 420-P
4604
● 4603
● 4602
● PR80/PR82BF
DC54
DC53
● DC52
PR80 Size 2-5
Size 4
Size 3
Size 2
100
5016N
CORBIN/
CRL
6000
CR801
CR801S
● DC6200
● DC3200
PR90
416
316
116
100
100
● 8916
8616
● 7400
● 7304
● 7303
● 7204
● 7203
● SC60/SC61
SC64
● SC93
SC60 Size 2-5
SC94
HARDWARE
DORMA
● SC70
FALCON
SC81
SC80
DOR-O-MATIC
GENERAL LOCK
C900
C7500
C7300
● C5025/C5014
C5025 Size 2-5
GLOBAL
● TC600
TC4300
TC500
TC400
TC200
TC204
TC2203
● TC302
● TC2202
DOOR CONTROL
HAGER
5100
● 5200
5300
5400
● 5400
● 5400
8050
854
853
● 852
● 754
753
● 752
654
653
● 652
534
533
● 532
● 604
● 603
602
● 5103
● 5102
Size 2-5
INTERNATIONAL
● 9000
44CI
5000
DOOR CLOSER
LCN
● 1260
4040
Size 1-5
NORTON
PDQ
● 7500
8501
7100
5300
1100/3100
1100/3100
1331
1130
1134
8301
1600
Manufacturing
SARGENT
● 1431
● 281
STANLEY
D3550/D3551
D4550/D4551
S.PARKER
900BC
● D1650/D1651
D1650 Size 2-5
● BF900
814BC
TAYMOR
● 800/800BF
1900
800 Size 2-5
TELL
YALE
● 700
900
4400
800
3501
YMDC2501
3301
600
500
50
● 5104
YMDC1101
● The same mounting hole pattern with similar application ● Different mounting hole pattern in the same power size
All brand names & trademarks used are properties of their respective owners
10
DISTRIBUTION BY:
Philadelphia Hardware Group,
Group Inc.
SAN DIEGO DISTRIBUTION CENTER
(Home Office)
6590 Top Gun Street
San Diego, CA 92121
Tel: (858) 642-0450
Fax: (858) 642-0454
Toll Free Tel: 1-800-545-2309
Toll Free Fax: 1-800-828-0988
philihardware.com
CHICAGO DISTRIBUTION CENTER
3687 Darlene Court
Aurora, IL 60504
Tel: (630) 692-0316
Fax: (630) 692-0320
Toll Free Tel: 1-800-406-5138
Copyright ©2010 Philadelphia Hardware Group, Inc. All rights reserved.
SEATTLE DISTRIBUTION CENTER
3705 166th Place N.E.
Arlington, WA 98223
Tel: (360) 659-7680
Fax: (360) 659-7401
Toll Free Tel: 1-800-333-5156
Toll Free Fax: 1-800-596-5156

Door Closers - ConstructionBuildingComponents.com

Transcription

Similar documents

SaeboFlex / SaeboReach Brochure

Zak McKracken – Mayan Maze Map

Color Flyer - World Manufacturing

LifeScapes Highboy Storage Shed

LiftMaster 81LM

Rilo Kiley After Hours

New York Arm Wrestling® and Mulcahy`s Pub Presents the

CFOX pdf - La Marca

Value: $1700• 2 Hours in Length • Safety

FH 2016 Toyota Fortuner