INSTALLATION INSTRUCTION

INSTALLATION INSTRUCTION
Installation option 1
(without extended arms):
VESA:
100X100 mm
200X100 mm
200X200 mm
Installation option 2
(with extended arms):
Max VESA:
600X400 mm
MODEL
MD2296
Please read this instruction carefully before installation.
Fits for most 42-70 inches Plasma, LCD and LED TVs.
Weight capacity: 45.5 kg (100 LBS).
Thanks for your purchase! We strive to provide products and services of exceptional quality.
We sincerely invite you to write a review with a good rating. If you wouldn't rate any part of your
experience with five star, please contact us immediately by [email protected],
so that we may resolve the issue for you.
(A0)
US WARNING!
Safety Warning: Thank you for choosing Mounting Dream TV mount. For safe application of model
MD2296, and preventing yourself or others from danger or property loss, please read through this
manual before use. If you do not understand these instructions or have any doubt over safety of
installation, please contact qualified contractor or Mounting Dream customer service. Please check
carefully before assembly to ensure no parts missed or damaged. Our customer service representative
will assist you timely in installation to solve the issue of parts shortage or damage. Replacement parts
purchased through authorized distributor will be delivered to your door. Please do not use defective
parts. Incorrect installation may result in product damage or body injury. Do not apply this product to
any purpose not indicated by Mounting Dream. We shall bear no responsibility for any damage or
injury resulted from incorrect installation, incorrect assembly or misuse.
JP
MD2296
RU
PE Y PE
EH E!
:
MD2296,
,
.
-
,
,
,
.
,
,
,
.
-
DE
,
.
HINWEIS!
Sicherheitshinweis:
Benutzerhandbuch bitte vor dem Gebrauch. Wenn Sie diese Anweisungen nicht verstehen, oder einen Zweifel
nicht zu einem anderen Zweck, der nicht durch MOUNTING TRAUM angegeben wird. Wir tragen keine
Missbrauch verursacht werden.
FR AVERTISSEMENT!
dommage des biens, veuillez lire soigneusement ce manuel avant l'usage. Si vous ne pouvez pas comprendre
ES
ADVERTENCIA!
Kongzhongshijie, para garantizar el uso en seguro del modelo MD2296, evitar al usuario y otras personas
contratista calificado o Centro de servicio al cliente, Antes de asemblar, verifique cuidadosamente para
asegurarse de que no encuentre la falta de piezas o piezas defectuosos , nuestros representantes deservicio al
, la asamblea incorrecta o uso incorrecto.
AR
!
:
"
"
MD2296
.
.
.
.
"
".
.
CN
:
Attention:
For parts shortage or damage, please contact us directly by [email protected].
New delivery will be timely sent to replace missed or defective parts.
Installation tools:
2M
Bubble level
Spanner
17-19mm
Stud finder
Hammer
Band tape
2m
Pencil
(3/8")
(7/32")
Screwdriver
Electrodrill
Gifts
HDMI cable
1pc
Velcro cable tie
3pcs
Bubble level
1pc
Part list
B-Left extended arm
2pcs
D-TV bracket
2pcs
Bubble level
MOUNTING TEMPLATE
16"(406mm)
8"(203mm)
A-Wall plate unit
1pc
1
C-Right extended arm
2pcs
E-Mounting template
1pc
Installation hardware
F--Lag bolt
4pcs
I--M6X8 Bolt
2pcs
H--M8 Washer
4pcs
G--Anchor
4pcs
J--M8X14 Bolt
8pcs
L--5mm Allen key
1pc
K--4mm Allen key
1pc
M--M6X12 Bolt
2pcs (pre-assembled)
Hardware for TV installation
a--M4X12 bolt
4pcs
b--M5X12 bolt
4pcs
c--M6X12 bolt
4pcs
d--M8X16 bolt
4pcs
e--M4X30 bolt
4pcs
f--M5X30 bolt
4pcs
g--M6X30 bolt
4pcs
h--M8X40 bolt
4pcs
i--M5/M6 spacer
4pcs
j--M8 spacer
4pcs
k--M5/M4 washer
4pcs
l--M6 washer
4pcs
m--M8 spacer
4pcs
2
Installation instruction
Step 1 Remove the bolts (M) with Allen key (K) to separate wall
plate unit (A) into two pieces.
Wall plate
A Wall plate unit
TV plate
M
Step 2
Step 4
Step 3
G
H
F
(3/8")
UP
Concrete wall
CAUTION
Stick the bubblel level on the
Mounting template (E), put (E)
on your desire position, adjust
it make it level and stick in on
the wall.
Use 3/8" diameter drill bit to drill 4
holes at marked positions to a
depth of 2.5".
Take down the Mounting template,
put 4 anchors (G) into drilled holes,
and tap each anchor flush with the
wall by using a hammer. Then put 4
lag bolts (F) through the washers (H)
into the anchors, and tighten each
bolt by using a spanner to mount the
wall plate securely.
To avoid potential personal injury or property damage:
1. Make sure the logo on the wall plate is upward as the picture shows.
2. The wall must be capable of supporting five times the weight of the TV plus the mount.
3. All anchors/lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate.
Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
Step 2
Step 3
Step 4
16"
(7/32")
Wood stud
3
Use a stud finder to make marks at
the edges of two studs, and mark
centerlines of studs. Then place
Mounting template (E) along the
centerlines, level it and stick it.
Use 7/32" diameter drill bit to
drill 4 holes at marked
positions to a depth of 2.5".
Take down the Mounting template, put
4 lag bolts (F) through the washers (H)
into the drilled holes, and tighten each
bolt by using a spanner to mount the
wall plate securely.
Select the TV hardware diameter and length
Your TV type will help you determine which hardware configuration to use.
Hand thread bolts (a, b, c, d, e, f, g, h) into the threaded inserts on the back
of your TV to determine the correct bolt diameter(M4, M5, M6 or M8) and
length.
CAUTION: Avoid potential personal injuries and property damage! Verify
that there are adequate threads to secure the plate to the monitor. If you
encounter resistance, stop immediately and contact customer service. Use
the combination of shortest bolts and spacers to accommodate your needs.
Using hardware that is too long may damage your TV.
Carefully lay your TV on a
non-abrasive surface, or lay it
with a padding underneath it so
as not to damage the screen.
OK
4
Step 5 Attach TV plate to the back of TV
Installation option 1:
If the VESA dimension is 100 mm x 100 mm(3.94 in x 3.94
in), 200 mm x 100 mm(7.87 in x 3.94 in) or 200 mm x 200
mm(7.87 in x 7.87 in), take the following image as
reference.
200 mm
200 mm 100 mm
100 mm
100 mm
200 mm
Attach TV plate to the back of TV directly:
1 For the TV with flat back, mount the wall plate with bolt/washer
combination of a+k, b+k, c+l, d.
a
k
M4 Diameter Bolt
M5 Diameter Bolt
5
2
For TV with irregular back, mount the wall plate with
bolt/washer/spacer combination of e+k+i, f+k+i, g+l+i, h+j/m.
(Spacers are highly recommended to be added, thus enlarge the
space between TV and brackets for better functionality.)
Attention: Because of the
TV with irregular back
which makes the VESA
holes recessed, you might
need spacers to fill the
gap.
spacers(i,j)
Vertical view
i
i
k
e
f
k
M4 Diameter Bolt
M5 Diameter Bolt
l
g
h
j/m
i
M6 Diameter Bolt
M8 Diameter Bolt
6
Installation option 2:
If the VESA dimension is greater than 200 mmX200 mm(7.87 in x
7.87 in), and less than the max VESA 600 mm
(23.62 in
), take the following image as reference.
Max: 400 mm
00
ax: 6
mm
M
Attatch and fasten the left extended arms (B) to the right
extended arms (C) by using bolts (I) with Allen key (K) (figure 1).
Then attach TV plate to extended arms by using bolts (J) with
Allen key (L) (figure 2) to get figure 3.
L
TV plate
figure 1
7
figure 2
figure 3
Insert the brackets (D) into the figure 3 to get figure 4.
D
D
figure 4
8
After the assembly of figure 4, attach it to the back of TV:
For the TV with flat back: Slide the TV brackets (D) until the bolt
holes align with the TV's VESA holes. Then mount the wall plate
with bolt/washer combination of a+k, b+k, c+l, d.
1
k
a
k
b
M5 Diameter Bolt
M4 Diameter Bolt
Attention: Make sure the
end of TV brackets (D)
with round holes is facing
upward.
Attention: Screw in
bolts a bit, then pull
upward brackets to
reduce the gap between
bolts and bolt holes to
make two brackets
parallel. Then fasten
bolts.
l
c
M6 Diameter Bolt
9
d
M8 Diameter Bolt
2
For the TV with irregular back:
Slide the TV brackets (D) until the bolt holes align with the TV's
VESA holes. Then mount the wall plate with bolt/washer/spacer
combination of e+k+i, f+k+i, g+l+i, h+j/m.
spacers(i,j)
Vertical view
Attention: Because of the
TV with irregular back
which makes the VESA
holes recessed, you might
need spacers to fill the
gap.
i
k
e
f
M4 Diameter Bolt
Attention: Screw in
bolts a bit, then pull
upward brackets to
reduce the gap
between bolts and
bolt holes to make
two brackets
parallel. Then fasten
bolts.
k
i
M5 Diameter Bolt
Attention: Make sure the
end of TV brackets (D)
with round holes is
facing upward.
l
g
i
h
j/m
M6 Diameter Bolt
M8 Diameter Bolt
10
Fasten extended arms with brackets by using bolts (J)
with Allen key (L).
L
11
Step 6 Hang the pre-assembled TV unit on the wall plate.
(Below images only show the TV plate with extended arms)
Attention: Cables are
highly recommended to
plug in before hanging
the TV on the wall plate.
Two people are recommended
to hold and position the TV .
Step 7 Make sure the TV unit is horizontal, you can adjust the TV
plate a little bit (+/-5 degrees) to level the TV, then fasten
TV plate by bolts (M) with Allen key (K).
M
Tip: If TV still not level after adjustment, please loosen bolts a bit,
hold TV to adjust to level, then fasten bolts securely with Allen key.
12
Step 8 Adjust the tilting angle with spring loaded handle:
Hold the TV and adjust it to your desired position, and fasten
the handle and the bolt opposite to the handle.
Handle
Bolt
K
To fasten the handle:
Push
Pull
Step A
Turn handle
clockwise
until stopped
by mount.
Step B
Pull out the
handle.
Step C
Step D
While holding
Push and
handle away
release
from mount,
the handle.
turn it
counterclockwise.
Adjust the swivel angle:
Grab TV and slide it to your desired direction.
13
Step E
Turn handle
clockwise to
further fasten
the mount.
Repeat these
steps until
TV firmly
tightened.
Step 9 Manage TV cables orderly and tie them with velcro cable
ties.
Product dimensions:
650 mm
MAX:600 mm
MIN:100 mm
72 mm
420 mm
MAX:400 mm
MIN:100 mm
396 mm
If you have any questions about the installation, please feel free to contact our after-sales mailbox: [email protected].
For more information, please visit our website: www.mountingdream.com
14